pwr_avg provides an average voltage, current, and power over the last
1 minute. It's up to the battery drivers to implement this
functionality.
This change allows us to have better power tracking while minimizing
the power impact on the EC, because
- the pwr_avg command only needs to be called once every minute, and is
short, thus less expensive to parse on ECs without a UART buffer
- the work done to keep the avg is partially done by the batteries
already and it's just a question of retrieving it.
undefined on wheatley since no power debugging planned on that board.
usage:
> pwr_avg
mv = 7153
ma = -605
mw = -4327
BUG=chromium:752320
BRANCH=None
TEST=make buildall -j
Change-Id: Id1a3479d277aedf90dfa965afb4ee9136654b1cf
Signed-off-by: Ruben Rodriguez Buchillon <coconutruben@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/823884
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Without this, the battery will discharge if we disallow battery
charging (e.g. calling charge_request with either voltage == 0 or
current == 0, either by policy, or when the battery is full).
Also update config.h to set the option whenever isl923x is used.
BRANCH=none
BUG=b:66575472
BUG=b:35585464
TEST=make buildall -j
Change-Id: Id5515d5ea82a393a3693a3da44cbdc2778296a95
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/856538
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
On ISL923x, PSYS output is always enabled when the AP is on
(provided CONFIG_CHARGER_PSYS is enabled).
We add support for charger_get_system_power function, reading PSYS
value, when CONFIG_CHARGER_PSYS_READ is defined. This will be used
by the charging algorithm on lux.
We also rename CONFIG_CMD_CHARGER_PSYS to CONFIG_CHARGER_PSYS_READ
as CONFIG_CHARGER_PSYS_READ provides both "psys" console command
and the new function. We also cleanup unneeded undefs in board
files.
Note that this does not implement the function on bd9995x, but this
could be done without too much effort.
BRANCH=none
BUG=b:71520677
TEST=On lux, without AC connected, check that "psys" output roughly
matches the output current from the battery.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Change-Id: Ie1ce8e0ac103daacc5a08b8ccae604d1d83551b8
Reviewed-on: https://chromium-review.googlesource.com/848487
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
CONTROL1 bits can be modified from multiple tasks:
- charger_enable_otg_power (charger or pd task)
- charger_discharge_on_ac (host command or console)
- charger_enable/disable_psys (chipset task)
- print_amon_bmon (console)
Since we use I2C read, modify, then I2C write access pattern,
there is a small chance of races between these accesses:
let's protect them with a mutex.
Also, the current code sometimes uses charger_get_option/set_option
instead of manipulating CONTROL0 directly: fix those to regain
a bit of the extra code size caused by the mutex.
BRANCH=none
BUG=b:67029560
TEST=Flash lux, battery charges, amon works fine.
TEST=Flash elm, battery charges.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Change-Id: If375d9922db53dd582582bfa44d6218fe0b416ec
Reviewed-on: https://chromium-review.googlesource.com/848486
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
This function sets up and enables "OTG" mode on the charger chip
(i.e. use the charger to provide power from the battery).
It also records the output current in curr.output_current, to
make sure that the charger loop is aware that current is provided
externally.
We also add a CONFIG_CHARGER_OTG to remove these functions on
boards that do not require it.
BRANCH=none
BUG=b:65697962
TEST=On wand, when discharging, battery status is updated every
5 seconds (and not every 60 seconds).
Change-Id: Ibf93933436f3eb24552a8e1eb9d97522fca2ce79
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/842743
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Old oak boards that still use these functions have long been
deprecated, let's make the unneeded functions static.
BRANCH=none
BUG=b:35573263
TEST=make buildall -j => makes newsizes: up to 64 bytes saved on
a few boards.
Change-Id: I8f2503ce324e34b87b3bbfa3c509079357880c9e
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/848574
Reviewed-by: Shawn N <shawnn@chromium.org>
This adds the driver for the SB-TSI temp sensor.
This is a sensor on the AMD AP SOC (Stoney Ridege FT2) that acts like an
8-pin temp sensor with an I2C interface.
BUG=b:69379715
BRANCH=None
TEST=Build
Change-Id: Iaafe6c7beb3e02e4e341617e8f117c03c0a882a2
Signed-off-by: Alec Thilenius <athilenius@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/833346
Commit-Ready: Alec Thilenius <athilenius@google.com>
Tested-by: Alec Thilenius <athilenius@google.com>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Added I2C sensors ADT7481 and TMP411 with config
items and build rules.
BRANCH=none
BUG=
TEST=Define CONFIG_TEMP_SENSOR_ADT7481 or _TMP411
and build board.
Change-Id: I4d1eb55ee56ad3f42787538bb839193e683d0a60
Signed-off-by: Scott Worley <scott.worley@microchip.corp-partner.google.com>
The boards need to have 5V masked off from the power good tree.
Additionially, Meowth needs to have the COMP_C fault masked from the
fault mask because its enable is connected and not grounded like on
Zoombini.
BUG=b:69935563
BRANCH=None
TEST=flash zoombini; Verify that we can boot to S0.
Change-Id: Ia51004a131e7c31d0e5ee59d87ab13455b822779
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/807632
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
rt946x_closest_reg_via_tbl() is buggy and doesn't
return the right reg value because of misuse of ARRAY_SIZE().
We should fix it.
Meanwhile, since rt946x_closest_reg_via_tbl() is only called in
rt946x_set_boost_current(), let's just delete rt946x_closest_reg_via_tbl()
and move its code to rt946x_set_boost_current().
BUG=b:70524967
BRANCH=none
TEST=Confirm reg 0x0a is set correctly
Change-Id: Ie9c90ebf63596a52f864ff5809488731edc41fff
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/830895
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
We add 2 hashes that each map to a list of allowed commands
(command list is secret, and provided by Elan).
UPDATE_EXTRA_CMD_TOUCHPAD_DEBUG on the USB interface have the
following format for the parameter:
- param[0]: must be 0xff
- param[1]: offset of the I2C command in data
- param[2]: command length
- param[3-4]: read-back length (MSB first) over I2C, can be 0
- param[5-49]: data, is verified using SHA-256 hash.
The I2C command pointed at by param[1-2] is then sent over
I2C, and the data is read back into a shared buffer of size
param[3-4].
The data can be fetched over USB by a single byte USB update
touchpad debug command (indicating an offset in 64-bytes unit),
fetching data from the shared buffer in blocks of 64 bytes.
BRANCH=none
BUG=b:63993891
TEST=Elan can run debugging commands using their proprietary tool.
Change-Id: Idb19bcb940b7f030c3b3aeaf39d6b725fcb9ef34
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/763576
Reviewed-by: Chun-ta Lin <itspeter@chromium.org>
The PPC needs to update its Vbus source current limits whenever our
policy changes on the PD ports. This commit simply adds and API to do
so.
BUG=None
BRANCH=None
TEST=With some extra code to enable 3A out, flash zoombini; Plug in a PD
device to a port, verify that it gets 5V @ 3A. Plug in a second device,
verify that we re-send new source caps of 5V @ 1.5A.
TEST=Repeat above for meowth.
Change-Id: Ifa4bc8b7df87f7730f2bcded842906d43171394b
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/818335
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Right now, the only events that are unmasked by default are overcurrent
conditions on PP1. This commit adds a simple interrupt handler and
introduces a board specific callback when the overcurrent status changes
on a port. This way, a board can take whatever action it desires with
the notification.
BUG=b:69139844
BRANCH=None
TEST=Flash zoombini with SN5S330 stuffed. Verify that board boots okay.
TEST=With some extra code to setup the interrupt handler, attempt to
exceed the current limit set, verify that interrupt handler is called.
Reduce the current pulled to under the current limit, verify that the
condition is no longer present.
CQ-DEPEND=CL:797937
Change-Id: Id3321c5703f9608da895be0ed5841f2fb76e734e
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/797936
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
We've been using the basic configuration (EZ config) to
initialize max17055.
It doesn't require battery profile, but the accuracy of fuel gauge
is not the best.
With a full battery profile in place, we should extend our driver
to import the battery profile for advanced config.
It should boost the accuracy.
BUG=b:69634899
CQ-DEPEND=CL:812481
BRANCH=none
TEST=manually test on Scarlet rev2, 'battery' command shows reasonable
reading no matter is_ez_config is set as 0 or not.
Change-Id: Iaea2d3e20f5de4207a86d4fff5f1561aaba4d362
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/813038
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The SN5S330 has support for detecting when Vbus is present on a port.
This commit simply adds an API to query the PPC.
BUG=None
BRANCH=None
TEST=`make -j buildall`.
TEST=Flash a board with the SN5S330, with some extra code, verify that
Vbus can be detected with this API.
Change-Id: I45bf7ff24bcdc447efe12932f51f8094108e29d5
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/791502
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The default sourcing current limit can be set by the following config
option:
CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT
However, the way that this macro was being used was incorrect for the
SN5S330 driver. Since, enum values are not known at compile time, the
check needs to happen during runtime. This commit makes this change.
BUG=None
BRANCH=None
TEST=Enable CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT on a board that uses
the SN5S330, verify that there are no build errors.
Change-Id: I04a1fa1e2e42c2f4ba49f1769857a8796b2f0a6f
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/791501
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
This commit introduces a driver framework for power path controllers.
It provides some common PPC APIs as well as allowing a board to use
multiple different PPCs drivers/parts. This should make it easier to
add PPC drivers in the future.
BUG=None
BRANCH=None
TEST=`make -j buildall`
TEST=Flash zoombini; verify PPC works as expected.
TEST=Flash meowth; verify PPC works as expected.
Change-Id: Icfb99f384610590b431456cfd28d4aff18442cb2
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/807630
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
It will be useful to determine if a FET is enabled or not. For example,
to determine if we are sourcing power to a downstream device. This
commit simply adds an API to check if a FET is enabled or not.
BUG=None
BRANCH=None
TEST=`make -j buildall`
Change-Id: I1f8198342cf225ce9a10d218607bcfbe6aef618c
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/791498
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
When the SN5S330 is powered initially, there will be certain events set
that will assert its interrupt line. As part of the initialization for
this part, we should clear all the pending interrupts and setup the
masks for the events that we care about.
This commit clears all interrupts at init time and masks all interrupts
except for overcurrent condition for PP1.
BUG=b:69139844
BRANCH=None
TEST=Flash zoombini; With nothing plugged in, verify that the interrupt
line is deasserted at boot.
TEST=Repeat the above test with a charger plugged in.
Change-Id: I7acc030184b76d6c38a729cb64658f71e376c819
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/783510
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
If VBUS toggles between 'present' and 'not-present', and fusb302 is the
arbiter of VBUS presence, wake the PD task so that it can take the
necessary protocol actions (eg. transition out of HARD_RESET_RECOVER).
BUG=b:69482362
BRANCH=None
TEST=On scarlet, issue EC reset with CableCreation source dock plugged,
verify we don't end up in hard reset loop.
Change-Id: I88d6102a6b5f4bd5151bae117c70f0a3ac0c09e7
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/804660
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
1. The original driver of OPT3001
a. didn't support to process the command of offset.
b. implemented command of range to setter/getter of Range Number Field
of chip.
But reffering to cros_ec_light_prox.c from linux kernel side, these two
commands are actually leveraged for in_illuminance_calib[bias|scale]
and these calibration factors should be applied into raw lux value read
from the chip.
2. Move ALS in Poppy / Soraka boards from ALS_TASK to MOTIONSENSE_TASK.
3. Mofify parameters of ALS in Reef board in order to adapt changes
here.
BUG=b:69236269
BRANCH=none
TEST=Manually test on the DUT.
Change-Id: Ic3b593feb3e4bc6da0bada6b5d614975f0cf2280
Signed-off-by: Marco Chen <marcochen@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/774341
Reviewed-by: Shawn N <shawnn@chromium.org>
Change the names to generic touchpad_* functions, instead of
vendor-specific names. Makes it a little easier to add drivers
for other touchpads.
Also fix console_channel.inc to add the channel whenever any
touchpad is used.
BRANCH=none
BUG=b:68934906
TEST=make buildall -j
Change-Id: I6d268db5ebd53db272fb2ee7bbf06bbe80845734
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/778750
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
At the end of the sensor initialization, all _init sensor routines set
the range to the default value from board.c file.
Put all the code in a single place, move it from sensor_common.c to
motion_sense.c.
BUG=none
BRANCH=none
TEST=compile
Change-Id: If89cf27c6438e0f215c193d68a480e027110174c
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/767610
Reviewed-by: Shawn N <shawnn@chromium.org>
On Nasher, sending TCPC_TX_BIST_MODE_2 to register 0x50 on the
PS8751 TCPC does not generate BIST Carrier Mode 2.
BUG=b:68337231
BRANCH=None
TEST=`make -j buildall`
Generated an eye diagram for Nasher on the GRL USB-PD test station
Signed-off-by: Sam Hurst <shurst@chromium.org>
Change-Id: Ia6e5df54a183c989a68d12be3a46896e3daea738
Reviewed-on: https://chromium-review.googlesource.com/741090
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
We support touchpad-specific debugging feature over the USB update
protocol. This will be used to fetch raw data from the sensor,
without requiring to remove the write-protect screw.
BRANCH=none
BUG=b:63993891
TEST=./usb_updater2 -g 00 -d 18d1:502b
Change-Id: I46dfd97aaa17b73a5893fe1e8c62327a302f829b
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/763574
Reviewed-by: Chun-ta Lin <itspeter@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The ISL9238 has a functionality where it will reload the adapter current
limit from a strap which is read from the PROG pin. This is problematic
when we decide to set the current limit prior to AC actually being
inserted. This commit disables this functionality from the charger.
It seems however that the charger will read the PROG pin and reload the
ILIM at least once before respecting the bits.
BUG=b:67120928, b:66017697
BRANCH=None
TEST=Plug and unplug and then plug again AC. Verify that the default
current limit is not set by the charger automatically.
Change-Id: Ia8e8742843f6ceb286635b31e0fe5c070a2b6dfe
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/759693
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Shamile Khan <shamile.khan@intel.corp-partner.google.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
The ISL9237/8 can both be powered by VSYS or AC, therefore, it's not
needed to reinitialize the charger after AC is present.
This commit moves the contents of charger_post_init() into a new init
function that will be run once at HOOK_INIT time.
BUG=b:67964166
BRANCH=None
TEST=make -j buildall
Change-Id: I637b1209f86f686013fee0783914fa1596076fa6
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/759692
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The ISL9238 has functionality for a input voltage regulation loop. By
default, the regulation reference voltage is set to 4096mV, however we
can be kinder to chargers by raising this regulation reference. In
testing, there appears to be insignificant change in current pulled at
the higher limit.
BUG=b:67964166
BRANCH=None
TEST=Flash a board with a ISL9238, verify that 0x4b reads as 0x0d00.
TEST=make -j buildall
Change-Id: I920c4b922106fca3001f2759cad0479a368f735b
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/745527
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
When sysjump to another image, if USB switch state and HW switch control
are not sychronized, the switch can be left in open state. This CL
resets USB switch on init to close USB.
BRANCH=oak
BUG=b:36234142
TEST=manual
plug BC1.2 charger, sysjump to another EC image and unplug the chager.
check pi3usb9281 control register(02h) bit2 == 1.
Change-Id: Iaadfaf51064ed1508271e974b9caf88b96bbe008
Signed-off-by: Rong Chang <rongchang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/502835
Reviewed-by: Shawn N <shawnn@chromium.org>
In order for BC1.2 detection to succeed, USB data switches must be
open. Previously we performed BC1.2 detection whenever VBUS transitioned
up to 5V, including on power swap. In fact, there is no need to do BC1.2
detection on a PD-capable port, since we will always charge using the
USB-C or PD negotiated ILIM. Skip BC1.2 detection on power swap (and
more generally when a partner port is known to speak PD) by manually
triggering BC1.2 detection. In addition, manage USB switch state
differently, so that "auto mode" is only enabled during BC1.2 detection.
BUG=chromium:780905
BRANCH=gru
TEST=Attach USB-PD phone capable of role swap. Verify USB 2.0 device is
enumerated on plug, and not re-enumerated through a series of
"pd # swap power" commands on the EC console. Also verify BC1.2 charging
and PD charging are still functional on kevin.
Change-Id: I1d7d4dee3bc8d2e7885e7adb49ded84b4f515ad5
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/755878
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The bd9995x driver was written to allow any PD port # to be VBUS or VCC,
but the mapping is broken in a few places. Since all boards use VBUS =
port 0, remove the conversion entirely.
BUG=chromium:781849
BRANCH=kevin
TEST=Verify PD and BC1.2 charging still works on kevin.
Change-Id: I3687866835d1684342d9f746d91b3a6079ab5cc4
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/755000
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
We didn't set BATT_FLAG_WANT_CHARGE in battery_get_params(), so
battery command always shows 'charging not allowed'.
Let's set the flag in the same condition as it is set in
battery/smart.c.
BUG=b:68027469
BRANCH=none
TEST='battery' on EC console shows 'Charging: Allowed'
Change-Id: Ifbdb6aee2572c8fc5f67103ca940738fb221ce5d
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/749025
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Add support the ITE IT5205 Type-C USB alternate mode mux.
BRANCH=none
BUG=none
TEST=1. Successfully verify chip ID.
2. Verify set_mux() and get_mux() functions set and return
consistent values.
3. The mux control register setting as expected after set_mux().
Change-Id: I9ff066dc9e74683df1371b70290e2aeaa86cb96b
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-on: https://chromium-review.googlesource.com/741211
Reviewed-by: Shawn N <shawnn@chromium.org>
The compass uses oversampling to produce accurate values.
MAX_ODR is functions of the repetitions setting.
80Hz is too high, calculate the frequency based on preset setting.
Currently, we use 'SPECIAL' that was calculated for Ryu.
BUG=b:68394559
BRANCH=eve,reef,poppy
TEST=Check with ectool motionsense info 3 the frequency is around 30Hz.
Before:
Min Frequency: 781 mHz
Max Frequency: 80000 mHz
After:
Min Frequency: 781 mHz
Max Frequency: 29579 mHz
Check with AIDA64 the compass is not stuck and return changing values.
Fixup of CL/570482
Change-Id: Idcfed1418f59e755e5647d018351c6a7397ffe1b
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/742146
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
This commit adds a basic driver for the TI SN5S330. This driver just
sets up the IC and provides an API to turn on or off the PP2 FET.
BUG=b:67663166, b:67663124
BRANCH=None
TEST=Enable code for zoombini; Flash a board which has the SN5S330
stuffed; Verify that we're able to perform PD negotiation and negotiate
all the way up to 20V.
TEST=Boot only on AC. sysjump to RW, verify that board does not
brownout.
Change-Id: I9c147ee8465eed878843cf902db301d62e8f627e
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/722104
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The GPIO that turns on Vbus for the BQ24392 is active low. This commit
changes the driver to make it clear that the enable is active low.
Additionally, the 5V rail is turned on prior to performing detection and
will be turned off if the AP is off.
For zoombini, since the chipset task can also control the 5V rail,
CONFIG_POWER_PP5000_CONTROL is enabled to do so in a task-safe way.
BUG=b:65992382, b:65991615
BRANCH=None
TEST=Verify that Vbus is turned on and the BQ24392 can output high on
charge detect pin.
Change-Id: Ib96ef9736ccc7fa285a3642ec6f3824a1df8f931
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/676762
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
