The ISL923x init function would initialize the charger's input current
to the board's defined default. For some boards like meowth and
zoombini, the default input current was set quite low, 128mA. When
sysjumping, all HOOK_INITs are called again and therefore the input
current limit would be reset even thought it would have been set
correctly prior to jumping. Setting the current limit so low, without a
battery, would cause a power failure and the PMIC would drop its power
OK signal and go into emergency shutdown.
This commit simply adds a check to whether the EC jumped to this image.
If it has, the charger input current limit is left unchanged. It will
be updated to the correct value by charge manager later on after
determine the attached charge supplier.
BUG=b:72129338
BRANCH=None
TEST=Flash meowth; Boot to S0 without a battery; Verify that PMIC_DPWROK
remains high.
TEST=Repeat above test for zoombini.
Change-Id: I7e5bbbbf3ec604c876cc4fa0163f8bb7feff4cc9
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/896960
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
If the sn5s330 PPC is being used to detect VBUS presence
(CONFIG_USB_PD_VBUS_DETECT_PPC), then enable interrupts and call
usb_charger_vbus_change when VBUS_GOOD changes.
BUG=b:72007153,b:72007492
BRANCH=none
TEST=Connect 3A and 1A USB-A chargers to each of Grunt's USB-C ports,
check that BC1.2 detection is working:
With 1A:
> chgsup
port=0/1, type=7, cur=500mA, vtg=5000mV, lsm=1
With 3A:
> chgsup
port=0/1, type=7, cur=2400mA, vtg=5000mV, lsm=1
TEST=Boot Grunt to OS, then connect USB2 mouse or USB3 flash drive to each
of Grunt's USB-C ports. Devices do not work due to b:71772180, but gpioget
shows EC is setting USB_C0/1_BC12_VBUS_ON_L correctly.
Change-Id: Iffc352105a321997adb364b9fbb8bafef248c224
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/887938
Reviewed-by: Jett Rink <jettrink@chromium.org>
Boards with a PPC will use the PPC to discharge the VBUS line instead
of the TCPC or GPIO discharge path.
BRANCH=none
BUG=b:72179253
TEST=Fall time after device removal on grunt within spec now
Change-Id: I822923a1cedb32a20efc3610cce4437ade3387f0
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/886563
Reviewed-by: Edward Hill <ecgh@chromium.org>
In the system, RT946x is always powered by the battery.
So even in battery cutoff mode, the reg values on RT946X are not reset.
We don't want RT946x to supply VBUS when DUT boots, which could mess up
PD state. So we need to disable VBUS output when RT946x initializes.
BUG=b:72228350
BRANCH=none
TEST=Confirm OPA_MODE (bit0 in reg 0x01) is clear after RT946x
finishes initialization
Change-Id: I32795b3bea64860b164c14b06aa1cd2551ebd8a0
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/890028
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
rt946x_block_read() is not implemented right.
It not only makes rt946x_init_irq() fail but also put
RT946x i2c module in an erroneous state temporarily.
BUG=b:72228350
BRANCH=none
TEST=manually on scarlet rev3:
1)Insert Plugable USB-C hub w/o AC
2)Run cutoff command on ec console
3)Hold Pwr button for a few seconds to wake up DUT
4)Repeat 2 - 3 for 10 times without seeing PD loops
Change-Id: I9304617f924e44288483afca5ab1b2923eb68ff0
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/890027
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
This chip controls the keyboard backlight. The backlight level is set
through PWM, but the chip needs to be enabled and configured before PWM
settings are recognized. This will be initially used for grunt and
zoombini.
BUG=b:69379749
BRANCH=none
TEST=In EC console for grunt: kblight 100; kblight 0
Change-Id: I5576d709687d8f61b5757485baa239ffd6b41a74
Signed-off-by: Benjamin Gordon <bmgordon@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/879082
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
VSYS_PRIORITY in the register VIN_CTRL_SET is set during bd9995x
initialization to ensure VSYS remains up and stable during deeply
discharged battery conditions. However, outside of this case, this bit
should remain cleared.
If set, there the input current limit is disabled between the time
that the boost converter is enabled (USB_SUS = 0) and charging is
enabled (CHG_EN = 1). This can lead to too much current being drawn
which results in the connecting port shutting off VBUS due to its
overcurrent protection. This has been observed when attempting to
charge one DUT from another chromebook port, or with a Type C only
charger.
This CL adds a check in the bd99965x driver implementation of
charger_get_voltage() that compares the current battery voltage to
its minimum voltage. If it's higher, then it's not a deeply discharged
battery and VSYS_PRIORITY can be cleared.
BUG=chromium:69143827,71814128
BRANCH=coral,eve
TEST=Tested with 2 Coral DUTs. Verified that VSYS_PRIORITY gets
cleared when the charger state machine gets the charger
parameters. Also verified that I can repeatedly initated charging from
one Coral device to another. Without this fix, this would fail most of
the of the time. Also tested Eve with deeply discharged battery to
make sure the startup conditon still works.
Change-Id: I5230560fa98e5bf16921eb4f2c70802eb962e7f3
Signed-off-by: Scott Collyer <scollyer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/875178
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
After 3 tries, the touchpad is reset by power-cycling it.
BRANCH=none
BUG=b:71688150
TEST=Short SDA/SCL lines, press on touchpad, see that touchpad tasks
retries transaction, and then resets the touchpad power.
TEST=Do ESD discharge, and see that touchpad always recovers.
Change-Id: If0b5eb936d4d2feb3d34a7ec8748869a1b915c34
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/872131
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
After VBUS is up, there is a delay of ~500ms for rt946x to determine
'VBUS is ready'.
But we need charger_task to detect AC presence and then set a proper
sleep time immediately.
When using fusb302 to detect VBUS, I almost don't see any delay.
BUG=b:71520398
BRANCH=none
TEST=Confirm BATTERY LED turns on immediately when AC is
plugged in a Scarlet in G3.
Change-Id: If1d6d40081b5822eeb9e012115f8deef172def37
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/869420
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
pwr_avg provides an average voltage, current, and power over the last
1 minute. It's up to the battery drivers to implement this
functionality.
This change allows us to have better power tracking while minimizing
the power impact on the EC, because
- the pwr_avg command only needs to be called once every minute, and is
short, thus less expensive to parse on ECs without a UART buffer
- the work done to keep the avg is partially done by the batteries
already and it's just a question of retrieving it.
undefined on wheatley since no power debugging planned on that board.
usage:
> pwr_avg
mv = 7153
ma = -605
mw = -4327
BUG=chromium:752320
BRANCH=None
TEST=make buildall -j
Change-Id: Id1a3479d277aedf90dfa965afb4ee9136654b1cf
Signed-off-by: Ruben Rodriguez Buchillon <coconutruben@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/823884
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Without this, the battery will discharge if we disallow battery
charging (e.g. calling charge_request with either voltage == 0 or
current == 0, either by policy, or when the battery is full).
Also update config.h to set the option whenever isl923x is used.
BRANCH=none
BUG=b:66575472
BUG=b:35585464
TEST=make buildall -j
Change-Id: Id5515d5ea82a393a3693a3da44cbdc2778296a95
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/856538
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
On ISL923x, PSYS output is always enabled when the AP is on
(provided CONFIG_CHARGER_PSYS is enabled).
We add support for charger_get_system_power function, reading PSYS
value, when CONFIG_CHARGER_PSYS_READ is defined. This will be used
by the charging algorithm on lux.
We also rename CONFIG_CMD_CHARGER_PSYS to CONFIG_CHARGER_PSYS_READ
as CONFIG_CHARGER_PSYS_READ provides both "psys" console command
and the new function. We also cleanup unneeded undefs in board
files.
Note that this does not implement the function on bd9995x, but this
could be done without too much effort.
BRANCH=none
BUG=b:71520677
TEST=On lux, without AC connected, check that "psys" output roughly
matches the output current from the battery.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Change-Id: Ie1ce8e0ac103daacc5a08b8ccae604d1d83551b8
Reviewed-on: https://chromium-review.googlesource.com/848487
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
CONTROL1 bits can be modified from multiple tasks:
- charger_enable_otg_power (charger or pd task)
- charger_discharge_on_ac (host command or console)
- charger_enable/disable_psys (chipset task)
- print_amon_bmon (console)
Since we use I2C read, modify, then I2C write access pattern,
there is a small chance of races between these accesses:
let's protect them with a mutex.
Also, the current code sometimes uses charger_get_option/set_option
instead of manipulating CONTROL0 directly: fix those to regain
a bit of the extra code size caused by the mutex.
BRANCH=none
BUG=b:67029560
TEST=Flash lux, battery charges, amon works fine.
TEST=Flash elm, battery charges.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Change-Id: If375d9922db53dd582582bfa44d6218fe0b416ec
Reviewed-on: https://chromium-review.googlesource.com/848486
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
This function sets up and enables "OTG" mode on the charger chip
(i.e. use the charger to provide power from the battery).
It also records the output current in curr.output_current, to
make sure that the charger loop is aware that current is provided
externally.
We also add a CONFIG_CHARGER_OTG to remove these functions on
boards that do not require it.
BRANCH=none
BUG=b:65697962
TEST=On wand, when discharging, battery status is updated every
5 seconds (and not every 60 seconds).
Change-Id: Ibf93933436f3eb24552a8e1eb9d97522fca2ce79
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/842743
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Old oak boards that still use these functions have long been
deprecated, let's make the unneeded functions static.
BRANCH=none
BUG=b:35573263
TEST=make buildall -j => makes newsizes: up to 64 bytes saved on
a few boards.
Change-Id: I8f2503ce324e34b87b3bbfa3c509079357880c9e
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/848574
Reviewed-by: Shawn N <shawnn@chromium.org>
This adds the driver for the SB-TSI temp sensor.
This is a sensor on the AMD AP SOC (Stoney Ridege FT2) that acts like an
8-pin temp sensor with an I2C interface.
BUG=b:69379715
BRANCH=None
TEST=Build
Change-Id: Iaafe6c7beb3e02e4e341617e8f117c03c0a882a2
Signed-off-by: Alec Thilenius <athilenius@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/833346
Commit-Ready: Alec Thilenius <athilenius@google.com>
Tested-by: Alec Thilenius <athilenius@google.com>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Added I2C sensors ADT7481 and TMP411 with config
items and build rules.
BRANCH=none
BUG=
TEST=Define CONFIG_TEMP_SENSOR_ADT7481 or _TMP411
and build board.
Change-Id: I4d1eb55ee56ad3f42787538bb839193e683d0a60
Signed-off-by: Scott Worley <scott.worley@microchip.corp-partner.google.com>
The boards need to have 5V masked off from the power good tree.
Additionially, Meowth needs to have the COMP_C fault masked from the
fault mask because its enable is connected and not grounded like on
Zoombini.
BUG=b:69935563
BRANCH=None
TEST=flash zoombini; Verify that we can boot to S0.
Change-Id: Ia51004a131e7c31d0e5ee59d87ab13455b822779
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/807632
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
rt946x_closest_reg_via_tbl() is buggy and doesn't
return the right reg value because of misuse of ARRAY_SIZE().
We should fix it.
Meanwhile, since rt946x_closest_reg_via_tbl() is only called in
rt946x_set_boost_current(), let's just delete rt946x_closest_reg_via_tbl()
and move its code to rt946x_set_boost_current().
BUG=b:70524967
BRANCH=none
TEST=Confirm reg 0x0a is set correctly
Change-Id: Ie9c90ebf63596a52f864ff5809488731edc41fff
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/830895
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
We add 2 hashes that each map to a list of allowed commands
(command list is secret, and provided by Elan).
UPDATE_EXTRA_CMD_TOUCHPAD_DEBUG on the USB interface have the
following format for the parameter:
- param[0]: must be 0xff
- param[1]: offset of the I2C command in data
- param[2]: command length
- param[3-4]: read-back length (MSB first) over I2C, can be 0
- param[5-49]: data, is verified using SHA-256 hash.
The I2C command pointed at by param[1-2] is then sent over
I2C, and the data is read back into a shared buffer of size
param[3-4].
The data can be fetched over USB by a single byte USB update
touchpad debug command (indicating an offset in 64-bytes unit),
fetching data from the shared buffer in blocks of 64 bytes.
BRANCH=none
BUG=b:63993891
TEST=Elan can run debugging commands using their proprietary tool.
Change-Id: Idb19bcb940b7f030c3b3aeaf39d6b725fcb9ef34
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/763576
Reviewed-by: Chun-ta Lin <itspeter@chromium.org>
The PPC needs to update its Vbus source current limits whenever our
policy changes on the PD ports. This commit simply adds and API to do
so.
BUG=None
BRANCH=None
TEST=With some extra code to enable 3A out, flash zoombini; Plug in a PD
device to a port, verify that it gets 5V @ 3A. Plug in a second device,
verify that we re-send new source caps of 5V @ 1.5A.
TEST=Repeat above for meowth.
Change-Id: Ifa4bc8b7df87f7730f2bcded842906d43171394b
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/818335
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Right now, the only events that are unmasked by default are overcurrent
conditions on PP1. This commit adds a simple interrupt handler and
introduces a board specific callback when the overcurrent status changes
on a port. This way, a board can take whatever action it desires with
the notification.
BUG=b:69139844
BRANCH=None
TEST=Flash zoombini with SN5S330 stuffed. Verify that board boots okay.
TEST=With some extra code to setup the interrupt handler, attempt to
exceed the current limit set, verify that interrupt handler is called.
Reduce the current pulled to under the current limit, verify that the
condition is no longer present.
CQ-DEPEND=CL:797937
Change-Id: Id3321c5703f9608da895be0ed5841f2fb76e734e
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/797936
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
We've been using the basic configuration (EZ config) to
initialize max17055.
It doesn't require battery profile, but the accuracy of fuel gauge
is not the best.
With a full battery profile in place, we should extend our driver
to import the battery profile for advanced config.
It should boost the accuracy.
BUG=b:69634899
CQ-DEPEND=CL:812481
BRANCH=none
TEST=manually test on Scarlet rev2, 'battery' command shows reasonable
reading no matter is_ez_config is set as 0 or not.
Change-Id: Iaea2d3e20f5de4207a86d4fff5f1561aaba4d362
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/813038
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The SN5S330 has support for detecting when Vbus is present on a port.
This commit simply adds an API to query the PPC.
BUG=None
BRANCH=None
TEST=`make -j buildall`.
TEST=Flash a board with the SN5S330, with some extra code, verify that
Vbus can be detected with this API.
Change-Id: I45bf7ff24bcdc447efe12932f51f8094108e29d5
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/791502
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The default sourcing current limit can be set by the following config
option:
CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT
However, the way that this macro was being used was incorrect for the
SN5S330 driver. Since, enum values are not known at compile time, the
check needs to happen during runtime. This commit makes this change.
BUG=None
BRANCH=None
TEST=Enable CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT on a board that uses
the SN5S330, verify that there are no build errors.
Change-Id: I04a1fa1e2e42c2f4ba49f1769857a8796b2f0a6f
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/791501
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
This commit introduces a driver framework for power path controllers.
It provides some common PPC APIs as well as allowing a board to use
multiple different PPCs drivers/parts. This should make it easier to
add PPC drivers in the future.
BUG=None
BRANCH=None
TEST=`make -j buildall`
TEST=Flash zoombini; verify PPC works as expected.
TEST=Flash meowth; verify PPC works as expected.
Change-Id: Icfb99f384610590b431456cfd28d4aff18442cb2
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/807630
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
It will be useful to determine if a FET is enabled or not. For example,
to determine if we are sourcing power to a downstream device. This
commit simply adds an API to check if a FET is enabled or not.
BUG=None
BRANCH=None
TEST=`make -j buildall`
Change-Id: I1f8198342cf225ce9a10d218607bcfbe6aef618c
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/791498
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
When the SN5S330 is powered initially, there will be certain events set
that will assert its interrupt line. As part of the initialization for
this part, we should clear all the pending interrupts and setup the
masks for the events that we care about.
This commit clears all interrupts at init time and masks all interrupts
except for overcurrent condition for PP1.
BUG=b:69139844
BRANCH=None
TEST=Flash zoombini; With nothing plugged in, verify that the interrupt
line is deasserted at boot.
TEST=Repeat the above test with a charger plugged in.
Change-Id: I7acc030184b76d6c38a729cb64658f71e376c819
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/783510
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
If VBUS toggles between 'present' and 'not-present', and fusb302 is the
arbiter of VBUS presence, wake the PD task so that it can take the
necessary protocol actions (eg. transition out of HARD_RESET_RECOVER).
BUG=b:69482362
BRANCH=None
TEST=On scarlet, issue EC reset with CableCreation source dock plugged,
verify we don't end up in hard reset loop.
Change-Id: I88d6102a6b5f4bd5151bae117c70f0a3ac0c09e7
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/804660
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
1. The original driver of OPT3001
a. didn't support to process the command of offset.
b. implemented command of range to setter/getter of Range Number Field
of chip.
But reffering to cros_ec_light_prox.c from linux kernel side, these two
commands are actually leveraged for in_illuminance_calib[bias|scale]
and these calibration factors should be applied into raw lux value read
from the chip.
2. Move ALS in Poppy / Soraka boards from ALS_TASK to MOTIONSENSE_TASK.
3. Mofify parameters of ALS in Reef board in order to adapt changes
here.
BUG=b:69236269
BRANCH=none
TEST=Manually test on the DUT.
Change-Id: Ic3b593feb3e4bc6da0bada6b5d614975f0cf2280
Signed-off-by: Marco Chen <marcochen@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/774341
Reviewed-by: Shawn N <shawnn@chromium.org>
Change the names to generic touchpad_* functions, instead of
vendor-specific names. Makes it a little easier to add drivers
for other touchpads.
Also fix console_channel.inc to add the channel whenever any
touchpad is used.
BRANCH=none
BUG=b:68934906
TEST=make buildall -j
Change-Id: I6d268db5ebd53db272fb2ee7bbf06bbe80845734
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/778750
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
At the end of the sensor initialization, all _init sensor routines set
the range to the default value from board.c file.
Put all the code in a single place, move it from sensor_common.c to
motion_sense.c.
BUG=none
BRANCH=none
TEST=compile
Change-Id: If89cf27c6438e0f215c193d68a480e027110174c
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/767610
Reviewed-by: Shawn N <shawnn@chromium.org>
On Nasher, sending TCPC_TX_BIST_MODE_2 to register 0x50 on the
PS8751 TCPC does not generate BIST Carrier Mode 2.
BUG=b:68337231
BRANCH=None
TEST=`make -j buildall`
Generated an eye diagram for Nasher on the GRL USB-PD test station
Signed-off-by: Sam Hurst <shurst@chromium.org>
Change-Id: Ia6e5df54a183c989a68d12be3a46896e3daea738
Reviewed-on: https://chromium-review.googlesource.com/741090
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
We support touchpad-specific debugging feature over the USB update
protocol. This will be used to fetch raw data from the sensor,
without requiring to remove the write-protect screw.
BRANCH=none
BUG=b:63993891
TEST=./usb_updater2 -g 00 -d 18d1:502b
Change-Id: I46dfd97aaa17b73a5893fe1e8c62327a302f829b
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/763574
Reviewed-by: Chun-ta Lin <itspeter@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The ISL9238 has a functionality where it will reload the adapter current
limit from a strap which is read from the PROG pin. This is problematic
when we decide to set the current limit prior to AC actually being
inserted. This commit disables this functionality from the charger.
It seems however that the charger will read the PROG pin and reload the
ILIM at least once before respecting the bits.
BUG=b:67120928, b:66017697
BRANCH=None
TEST=Plug and unplug and then plug again AC. Verify that the default
current limit is not set by the charger automatically.
Change-Id: Ia8e8742843f6ceb286635b31e0fe5c070a2b6dfe
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/759693
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Shamile Khan <shamile.khan@intel.corp-partner.google.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
The ISL9237/8 can both be powered by VSYS or AC, therefore, it's not
needed to reinitialize the charger after AC is present.
This commit moves the contents of charger_post_init() into a new init
function that will be run once at HOOK_INIT time.
BUG=b:67964166
BRANCH=None
TEST=make -j buildall
Change-Id: I637b1209f86f686013fee0783914fa1596076fa6
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/759692
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The ISL9238 has functionality for a input voltage regulation loop. By
default, the regulation reference voltage is set to 4096mV, however we
can be kinder to chargers by raising this regulation reference. In
testing, there appears to be insignificant change in current pulled at
the higher limit.
BUG=b:67964166
BRANCH=None
TEST=Flash a board with a ISL9238, verify that 0x4b reads as 0x0d00.
TEST=make -j buildall
Change-Id: I920c4b922106fca3001f2759cad0479a368f735b
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/745527
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
