Separate macros for defining delays to turn on and off VBUS on the
Raiden ports.
Tune the delays for Samus to provide extra headroom based off of
measured worst case times.
BUG=chrome-os-partner:34525
BRANCH=samus
TEST=load onto samus. connect two samus' and use twinkie to analyze
time between request and PS_RDY on connect and then on a power swap.
Change-Id: I65cec911e34c22a4aad136423362a3a65bc2ab2a
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/241761
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Do not request a voltage that is within the deadband where we
aren't sure if the boost or the boost bypass is on.
BUG=chrome-os-partner:34938
BRANCH=samus
TEST=test on samus with zinger. change the deadband to [10V, 20V]
and see that we only negotiate to 5V. change the deadband to
[13V, 20V] and see that we negotiate to 12V. change the deadband
to [10V, 13V] and see that we negotiate to 20V.
Change-Id: Id761aef35eeadfa2ab7d2ca31a48d4324625ab32
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/241528
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
For samus, on PD connection or on resume to S0, if we are a sink,
and the other side supports PR_SWAP, then attempt a power swap.
This adds callback functions into board policy file to check
and issue power or data swaps if required by the product.
BUG=chrome-os-partner:31195
BRANCH=samus
TEST=connect samus to zinger and make sure zinger always ends up
as SRC-UFP.
connect samus to samus with both in S0 and see that
they swap power roles once and not data roles.
connect one samus in S0 to one samus in S5 and see that the one
in S5 is sink. then when you boot the one in S5 it switches to a
source.
connect samus to samus with both in S0. do chgoverride 1 on one
side to start charging from the other samus. then on the same
side, turn off the machine (S5) and resume (S0), and see that it
is still charging from the other samus (ie has not switched roles
to source).
Change-Id: Ifab2465fccef77448ac4771a3c2de1c867cbbec4
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/238302
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Remove common code across all PD policy layers to select the requested
voltage and build a Request Data Object (RDO).
BUG=none
BRANCH=samus
TEST=Load onto samus and connect zinger. Make sure we request the right
voltage (first 5V, then after initial contract is made, 20V). Make
sure input current limit is set appropriately by checking limit on EC
console using charger command.
Change-Id: Ic6bda5e23b2d7b7d710ffdf085e7fbc1b0c3add9
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/233673
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Ensure that the PD source changes the output voltage after
tSnkTransition delay after having sent the ACCEPT message
(rather than before).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:33684
TEST=connect Zinger to a PD power sink and monitor VBUS and CC while
doing a 20V to 5V transition.
Change-Id: If86f59eec67630491f4e8dc13a52015ac2de918a
Reviewed-on: https://chromium-review.googlesource.com/230805
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Allow policy layer to request a PR or DR swap upon formation of
a power contract. Zinger always asks for a data swap so it can
be a UFP, and Samus asks for a data swap only if it is a UFP to
become a DFP.
BUG=chrome-os-partner:33754, chrome-os-partner:31195
BRANCH=samus
TEST=load onto samus and zinger and make sure they swap roles
upon connect with no collisions
Change-Id: I275c9669549c26f25c58f80845daad8edab11313
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/229327
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add support for DR_swap, data role swap command.
BUG=chrome-os-partner:33686, chrome-os-partner:28343
BRANCH=samus
TEST=test with samus and zinger. use "pd 1 swap data" command
and verify data role swaps by using twinkie and "pd 1 state".
Change-Id: I410309199cdeecb26847a6bf217523fdfe688cba
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/229192
For request message, add the operational and max current for each
board. If the requested power is less than the operational power
required, then set mismatch bit.
BUG=none
BRANCH=samus
TEST=make buildall. load onto samus, plug in zinger and see
that request 20V, operational current 3000mA and max
current of 3000mA.
Change-Id: I4df45d88b7e060f66ff5b806f6fe30803f1afcf7
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/227393
Reviewed-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add support for PR_SWAP command as per PD specification.
BUG=chrome-os-partner:28343
BRANCH=samus
TEST=test by connecting two samus' and running 'pd 1 swap power'
from console. verified that both sides switch power roles by
observing console output. also tested against third party
devices.
Change-Id: I0e8738b544de9f9a4348250630e67d0fefb4486d
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/225559
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Integrate charge_manager and include several API changes designed
for reporting voltage.
1. Make pd_choose_voltage set the chosen voltage for use by caller.
2. Add voltage parameter to pd_set_input_current.
3. Add pd_get_role to grab the sync / source state of a port.
4. Add charge manager PD + type C port initialization to the pd
state machine.
BUG=chrome-os-partner:32003
TEST=Manual on samus. Insert Apple charger, verify charge limit is
selected appropriately. Insert PD charger, verify that charge port
switches to PD port. Remove + reinsert chargers, verify that port /
limit is selected appropriately. Remove battery, insert power source, verify
that our power source port never becomes disabled.
BRANCH=samus
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Idf3198c71d2ddf1e401e766fc82a4b7a02aed068
Reviewed-on: https://chromium-review.googlesource.com/223758
Reviewed-by: Alec Berg <alecaberg@chromium.org>
All non-interactive console prints should use their tasks channel
parameter to make it easy for developers to inhibit console output.
This CL corrects printf's in the various usb_pd_policy files that
belong to the USB PD task to use cprintf(CC_USBPD, ...) instead of the
macro reserved for interactive console commands ccprintf.
BRANCH=none
BUG=none
TEST=manual, set 'chan 1' and see none of the previous chatter
relating to USB PD. set 'chan 0x08000000' and see it return.
Output from DFP side for SVDM discovery now looks:
SVDM/4 [1] ff008041 340018d1 00000000 11000008
[1119.966911 DONE]
SVDM/2 [2] ff008042 ff010000
[1119.970135 DONE]
SVDM/2 [3] ff018043 00100081
[1119.973437 DONE]
SVDM/1 [4] ff018184
Change-Id: I47e5f4ec2d4a6a25f171177ead5ebc99409f80b6
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/224191
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
So far, we always use channel 1 of the Tx timer and the configuration
code is hard coded. We need to support other channels for new Ryu
boards. Let's make this a configurable bit.
BRANCH=samus
BUG=chrome-os-partner:32660
TEST=make buildall
TEST=Plug in Zinger to Ryu and see 20V come up.
Change-Id: Id08d4eb0d6a5721d8a03672484d0892a0714383b
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/223836
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Some platforms may need to take different actions depending on which
port is requesting a limit. Add a new port parameter to the
pd_set_input_current_limit API to accomodate this.
BUG=chrome-os-partner:32003
TEST=Manual on samus_pd. Verify zinger charges battery.
BRANCH=samus
Change-Id: I1578252c751b3a80b4da6ca68e2a958934283cbf
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/222621
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Change default to request 20V.
BUG=none
BRANCH=none
TEST=Load onto a firefly. Plug in a zinger, make sure 20V LED
lights up. Press other buttons to make sure we can change the
requested voltage to 5V and 12V.
Change-Id: I3a3e63a6d0e4f01b9fe7c730468da75ad6783f41
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/211872
Reviewed-by: Vic Yang <victoryang@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Set input current limit based on the max current from the
PD negotiation. For samus, this information is passed to
the EC as a host command. For ryu, the max current is set
directly following a negotiation.
CONFIG_CHARGER_INPUT_CURRENT is now just the default limit,
but after a successful PD negotiation, the limit can be
raised.
Note, for now the input current limit for samus is set to
2/3 of the value negotiated for. This is due to hardware
problems measuring input current on p2b boards.
BUG=chrome-os-partner:28532, chrome-os-partner:24461
BRANCH=none
TEST=tested on a samus. Verified input current limit using
"charger" console command from EC. Input current limit
after a reboot is 512. When zinger is plugged in, it jumps
to the appropriate value (currently 1280mA), and when
the negotiation is changed using the "pd 0 dev 5" command
on the PD console, the input current limit is adjusted to
match (2000mA).
Change-Id: Iab9186a0f9814655e3240217a9baf4a38f15f84d
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/211023
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Remove code for preventing PD negotiation until the battery
is at some minimum SOC. This was originally necessary because
transitioning voltages would cause the source voltage to go
briefly to 0V, which would kill power to the system unless
the battery was at some minimum level of charge. But, that
isn't true anymore. It is safe to transition up or down in
voltage and the source voltage should never drop to 0V.
BUG=chrome-os-partner:29499
BRANCH=none
TEST=make -j buildall. No need to do any more testing because
this code has been disabled for a while.
Change-Id: I8a3dca117f01f0f9c7d04b5d489e4a8588a89be6
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/211021
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Previously if you were working on a single board you had to add BOARD=
to all of your make command lines. Now if you are in a board directory
you can just use "make", or "make clean", or any other top level make
command.
This commit also adds support for a top level "make flash" command that
can be used from the board directories as well. This command uses
openocd and requires that the board provides an openocd-flash.cfg file.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=none
TEST=(from a few board directories) make clean; make -j
(from the discovery-stm32f072 directory) make flash
Change-Id: Ie09a74881371169a2c3cd9cd9922f39f4873f1a6
Reviewed-on: https://chromium-review.googlesource.com/209669
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Adds dual USB-PD port support for samus. Both ports are in dual-role
and can perform either role.
Both ports work fine when only one of the ports is in use. But,
still having problems with PD errors on the lower priority port (port
0). If you have a charger plugged into port 0, and a type-C USB dongle
plugged into port 1, then port 1 has higher priority, and in the
SRC_DISCONNECTED state, every 1.5 seconds when it sends source cap
packet, we occasionally drop pings on port 0, which results in a
lot of start/stop charging.
BUG=chrome-os-partner:28585
BRANCH=none
TEST=Tested on samus to make sure both ports work when I
plug in a charger and a type-C USB dongle with a pull-down on the CC
line. Tested on plankton and zinger to make sure PD works as expected.
Change-Id: Ie7bde3e258f5cd23a0b82b626c0993a45b0df074
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/200750
Reviewed-by: Vic Yang <victoryang@chromium.org>
Tested-by: Vic Yang <victoryang@chromium.org>
This is a straightforward conversion of existing tables
into X-Macro style definitions for the GPIO alternate
functions. This change in itself, is not particularly
powerful, but having all GPIO settings in a single file
makes a board easier to understand.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=none
TEST=make buildall -j
Followed by manual testing of interrupt on change and UART
functionality on STM32F0 based discovery board.
Change-Id: Ib7f1f014f4bd289d7c0ac3100470ba2dc71ca579
Reviewed-on: https://chromium-review.googlesource.com/207987
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Use the interrupt as faster detection when VBUS is going off, so we are
not missing when the source is cutting its output due to a fault.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=Connect Firefly to Zinger, trigger a short OCP with the electronic
load, once Zinger has recovered from the fault, see Firefly
re-negotiating voltage.
Change-Id: I4d273a0007d1e79884e0acbf75509ab9c8578893
Reviewed-on: https://chromium-review.googlesource.com/207031
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Enable the VBUS detection to be able to re-negociate a PD contract when
we are losing power.
The VBUS_WAKE GPIO is broken on the current hardware (not triggered when
VBUS is 5V), so we fall back on using the ADC on VBUS_SENSE.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=With a Firefly connected to a Zinger,"fault" the power supply to
get it to turn off its output. See Firefly detecting the cut-off and
re-negotiating voltage.
Change-Id: Ia5f0734cbd8f20d84ce170cea191410bb72a87c3
Reviewed-on: https://chromium-review.googlesource.com/206944
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
The default VBUS voltage is 5V, let's switch on the matching LED rather
no LED when no voltage has been selected.
This allows to know that the board is powered.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=power up Firefly and see the 5V LED ON (if the cable is plug) or
blinking (if the cable is unplug).
Change-Id: I8f6525bc6f901daf21af9b20eede2a9b1e8dbfdf
Reviewed-on: https://chromium-review.googlesource.com/206940
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Fix the beginning and end of BMC PD communication:
- Initial transmission within 1us of taking control of CC line
- CC line released between 1us and 23us after last edge
- If final bit is a 0, then add two 1 bits to the end
- No garbage after the final bit
BUG=chrome-os-partner:30132
BRANCH=none
TEST=tested with a fruitpie, samus, and zinger.
verified timing on scope.
Change-Id: Ie45695eb367a7554cf5d5b76b6fbdf1e3fc85d29
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/206453
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Previously each board.h and board.c contained an enum and an array
for gpio definitons that had to be manually kept in sync, with no
compiler assistance other than that their lengths matched.
This change adds a single gpio.inc file that declares all gpio's
that a board uses and is used as an X-macro include file to
generate both the gpio_signal enum and the gpio_list array.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=none
TEST=make buildall -j
Change-Id: If9c9feca968619a59ff9f20701359bcb9374e4da
Reviewed-on: https://chromium-review.googlesource.com/205354
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Use a EC to PD host command to notify the PD MCU when a battery
is present and charged enough that it is ok to negotiate for a
higher power. The PD MCU will not negotiate until the host command
is received, which allows the system to be powered without a
battery or with a dead battery with 5V.
BUG=chrome-os-partner:28611
BRANCH=none
TEST=Tested on a samus:
1) Tested the normal case of battery charged and plugged in. When
charger is plugged in, the device immediately starts negotiating
for 20V and starts charging.
2) Tested with no battery. Plug in a charger, samus boots and stays
alive. VBUS measured at 5V. When a battery is plugged in, device
negotiates for 20V and starts charging.
3) Tested dead battery by taking a battery with no charge, and
plugging in zinger. Everything boots, but PD does not negotiate
for power. Then when battery reaches 1%, PD negotiates and zinger
switches to 20V without causing a reboot.
Change-Id: Iaa451403674e86cddbd3fe80e9503584910be576
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/201958
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Detect loss of VBUS when acting as PD sink and go to the disconnected
state. This allows us to renegotiate power when power supply drops
and switches to 5V.
BUG=none
BRANCH=none
TEST=On a samus, tested by running for a couple of hours, and verifying
that occasionally when zinger drops from 20V to 5V, we detect it and
go to the disconnected state. Note, this only happens a couple times
every hour.
Change-Id: I237d267824ff564662c9c02e525ce2613ed229e6
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/200365
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Our code base contains a lot of debug messages in this pattern:
CPRINTF("[%T xxx]\n") or ccprintf("[%T xxx]\n")
The strings are taking up spaces in the EC binaries, so let's refactor
this by adding cprints() and ccprints().
cprints() is just like cprintf(), except that it adds the brackets
and the timestamp. ccprints() is equivalent to cprints(CC_CONSOLE, ...)
This saves us hundreds of bytes in EC binaries.
BUG=chromium:374575
TEST=Build and check flash size
BRANCH=None
Change-Id: Ifafe8dc1b80e698b28ed42b70518c7917b49ee51
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/200490
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Detect over-current and over-voltage and trigger a fault.
The over-current threshold is 10% over 3A (3.3A).
Only currently implement the slow protection,
the fast interrupt-based one will be done later.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:28331
TEST=with Zinger connected to an electronic load, adjust the current to
3.35A and see the output voltage cut.
Change-Id: I0e848192392fd73f0839d4bcb806528b2a6b9122
Reviewed-on: https://chromium-review.googlesource.com/197947
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
