Added check for collision just before transmitting on CC line.
To check for collision, RX monitoring is left on all the time
(except when in the act of receiving or transmitting, or in
between receiving and sending a goodCRC), and a
simple check for RX transmission started is used to see if the
CC line is idle or not.
RX monitoring is also changed to only trigger on 3 edges within
20us, as per the PD spec.
When a collision is detected by seeing that CC is not idle, the
transmitting packet is dropped.
BUG=chrome-os-partner:30135
BRANCH=samus
TEST=load onto samus and zinger. make sure we negotiate and make
sure custom VDMs succeed. enabled pings and made sure we stay
alive with pings for a few min.
Also added code to pd_rx_handler to toggle a test point on EVT
board to verify the timing of when we get RX interrupts:
Change-Id: I22d172163319437d3d901e019eda79d4d592f6b8
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/226118
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
For request message, add the operational and max current for each
board. If the requested power is less than the operational power
required, then set mismatch bit.
BUG=none
BRANCH=samus
TEST=make buildall. load onto samus, plug in zinger and see
that request 20V, operational current 3000mA and max
current of 3000mA.
Change-Id: I4df45d88b7e060f66ff5b806f6fe30803f1afcf7
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/227393
Reviewed-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Remove redundant 5V source PDOs in source cap packet. We only
need one 5V advertisement with the maximum current that we can
provide.
BUG=none
BRANCH=samus
TEST=make buildall
Change-Id: I94a01813787eb92fafbf600dcbbc8a2f0aa69e2b
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/227392
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Add support for PR_SWAP command as per PD specification.
BUG=chrome-os-partner:28343
BRANCH=samus
TEST=test by connecting two samus' and running 'pd 1 swap power'
from console. verified that both sides switch power roles by
observing console output. also tested against third party
devices.
Change-Id: I0e8738b544de9f9a4348250630e67d0fefb4486d
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/225559
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This is mostly the same as previous commits, but with increased delay.
Previously, we have short delays (e.g. 3ms) which is too short and may
cause instability.
Now that we have slowed down the time when running unit tests and
increased the delay, this shouldn't cause problems anymore.
BUG=chrome-os-partner:31200
TEST=Repeatedly run multiple unit tests in parallel.
BRANCH=Samus
Change-Id: Ib55e3adc5fd27a8e233996b4799dab3cefd62318
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/220734
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add back the test but only enable USB PD tasks for usb_pd test. This
should ensure that we do not break existing tests.
BUG=chrome-os-partner:31200,chromium:402335
TEST=make buildall
BRANCH=None
Change-Id: I4daa41a96a1067362b2c40a2a09fce733843bdff
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/211923
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Initial commit of usb_pd unit test. The test cases are very simple.
We'll add more test cases in similar format.
BUG=chrome-os-partner:31200
TEST=Pass usb_pd test
BRANCH=None
Change-Id: I9e3de5b2c032ee1d3670cde6d8227ce0378ae8a0
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/211643
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
