For oak, set a different list of task (no als, no accel) for compiling
revision 4 or less. Fix GPIO include issue.
BUG=chrome-os-partner:59423,chrome-os-partner:59084
TEST=compile for oak with board 4 and 5, tested on Reef.
BRANCH=kevin,reef
Change-Id: I09051a69cbad6d477a7b3bf9907f4c5c144b5136
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/424220
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Use LARGER_TASK_STACK_SIZE to increase stack size to 640 bytes.
Check HOSTCMD stack usage with "taskinfo" command while running
the suspend/resume stress test.
8 R HOSTCMD 00000001 21.133553 496/640
It exceeds 488 bytes of TASK_STACK_SIZE.
BUG=chrome-os-partner:51773
BRANCH=none
TEST=enter "suspend_stress_test -i spi32766.0" in AP to do
suspend test. System won't do cold reboot which is cause by
"Stack overflow in HOSTCMD task!".
Change-Id: Ic5edebc6b77637ca2c648798398e3f24bc87ca27
Signed-off-by: YH Huang <yh.huang@mediatek.com>
Reviewed-on: https://chromium-review.googlesource.com/336593
Reviewed-by: Rong Chang <rongchang@chromium.org>
The default target hardware is rev5. This is a maintainess change for
old and deprecated HW.
BRANCH=none
BUG=chrome-os-partner:49114
BUG=chrome-os-partner:50720
TEST=manual
for N=1,5 do
make BOARD=oak clean && make BOARD=oak EXTRA_CFLAGS="-DBOARD_REV=$N" -j
Signed-off-by: Rong chang <rongchang@chromium.org>
Change-Id: Ibb4ebf9fab429964ace7c3e548598f0fb08e7dea
Reviewed-on: https://chromium-review.googlesource.com/330065
Commit-Ready: Rong Chang <rongchang@chromium.org>
Tested-by: Rong Chang <rongchang@chromium.org>
Reviewed-by: Wei-Ning Huang <wnhuang@chromium.org>
refer to commit d341615383,
adds the base accelerometer as well as the gyroscope to the list of
motion sensors on the board, connect with SPI bus. They are currently
wrapped behind an ifdef for HAS_TASK_MOTIONSENSE and OAK_REV5.
BUG=chrome-os-partner:50312
BRANCH=none
TEST=Build Oak EC with driver enabled and verify that we can calcuate
a valid lid angle.
TEST=Verify that signs of accelerometer conform to those shown in the
Chrome/Android/HTML5 doc/spec. See description in accelerometer_types.h
TEST=Verify that signs of gyroscope conform to those shown in the
"Sysfs interface to EC accelerometers" document.
TEST=make buildall tests
Change-Id: I4d900bc6bd7329db6ea53660fae86e5e2bbe9028
Signed-off-by: Ben Lok <ben.lok@mediatek.com>
Reviewed-on: https://chromium-review.googlesource.com/319295
Commit-Ready: Rong Chang <rongchang@chromium.org>
Tested-by: Rong Chang <rongchang@chromium.org>
Reviewed-by: Rong Chang <rongchang@chromium.org>
refer to commit 574c806571,
adds the lid accelerometer to the list of motion sensors on the rev5.
Since commit bc404c94b4,
math_util.c is no longer to include "math.h" header file.
BUG=chrome-os-partner:50312
BRANCH=none
TEST=Build Oak EC with driver enabled and verify that valid
accelerometer data is read, and that range, resolution, and odr can all
be modified.
TEST=Verified that signs of accelerometer data conform to those shown in
the doc.
TEST=make buildall tests
Change-Id: I8df1b2331a1fbea82015b97985541e2ebc393d10
Signed-off-by: Ben Lok <ben.lok@mediatek.com>
Reviewed-on: https://chromium-review.googlesource.com/319332
Commit-Ready: Rong Chang <rongchang@chromium.org>
Reviewed-by: Rong Chang <rongchang@chromium.org>
Stack of PDCMD task may be overflow during plug/unplug stree test
with Apple's AV Multiport Adapter. Enlarge the stack size to avoid
system reboot.
BUG=chrome-os-partner:47728
BRANCH=none
TEST=Manual
1.Connect DUT to sink monitor via HDMI dongle.
2.Unplug HDMI USB from DUT side.
3.Plug HDMI USB cable to DUT USB socket.
4.Repeat (Plug and unplug) USB from DUT for 10 times.
Change-Id: Ib6a1fbd0a552b2c6d4656c12554e1306c21adb8a
Signed-off-by: Ben Lok <ben.lok@mediatek.com>
Reviewed-on: https://chromium-review.googlesource.com/315020
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Before oak rev4, BC 1.2 status change was polled on VBUS change. The
designed is changed to use a single interrupt pin for both ports.
BRANCH=none
BUG=chrome-os-partner:42610
TEST=manual
make EXTRA_CFLAGS=-DBOARD_REV=3 BOARD=oak -j
emerge-oak chromeos-ec
load on oak rev3 and check BC 1.2 charging current
Change-Id: I9e6cdbb83468b5e4086cc86caadf7f2e3cbe6e48
Signed-off-by: Rong Chang <rongchang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/294442
Console command 'batter' reaches STM32F0's TASK_STACK_SIZE(488). Oak
needs a larger stack in development stage.
BRANCH=none
BUG=none
TEST=manual
load on oak and type 'battery' in console.
Change-Id: Iab3d0bd23837932acb873ecdeb194af74f10f29c
Signed-off-by: Rong Chang <rongchang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/277979
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Previously we supported using a single pi3usb9281 chip, or using two
chips on the same i2c bus behind a mux. Now that we need to support a
third configuration of multiple chips on different busses, it makes
sense to be able to configure the configuration freely at the board
level.
BUG=chrome-os-partner:40920
TEST=Manual on samus_pd. Plug USB charger, verify detection is correct
on both charge ports.
BRANCH=None
Change-Id: I120dcb1c3ceb6f013b92407effcd8cb66e7ffcce
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/276511
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Port CL:275072 to oak. Oak rev1 and rev1.5 type-C VBUS input controls
are connected to PD phy instead of EC. This change wakes both USB PD
task to handle power status change. This issue will be fixed in next
hardware revision, or enable TCPC power status alert.
BRANCH=none
BUG=chrome-os-partner:41167
BUG=chrome-os-partner:41226
TEST=manual
plug type-C charger into port 1
Change-Id: Ifea19276d0eb74f3e4cac509abece362e6e8af17
Signed-off-by: Rong Chang <rongchang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/275851
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add TCPM on EC side and TCPC on PD side to allow PD
communication. Enable PD communication on port 0.
BUG=none
BRANCH=none
TEST=load on oak. plug in hoho on port 0, and make sure
we successfully negotiate a PD contract. (note: you have
to manually enable 5V VBUS right now)
Change-Id: I0ce7c016545bc56c5e10f66b49b73722187f12dc
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/271829
Reviewed-by: Rong Chang <rongchang@chromium.org>
Reviewed-by: Sheng-liang Song <ssl@chromium.org>
Commit-Queue: Sheng-liang Song <ssl@chromium.org>
Add initial support for Oak rev1 board. This is just the
EC and includes battery charging but does not include
USB PD.
BUG=none
BRANCH=none
TEST=load on oak board and get console
Signed-off-by: Rong Chang <rongchang@chromium.org>
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Change-Id: I626f3921025fbc39ba22b04eeb6dd1084cd70777
Reviewed-on: https://chromium-review.googlesource.com/261678
