Default setting is at 48MHz.
For PLL frequency at 24MHz:
1. USB module can't work, it requires 48MHz to work.
2. SSPI clock frequency is divide by two.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. uart, i2c, timer, and pd modules are function normally
at different PLL frequency settings.
2. use 'flashrom' utility to flash EC binary with different
PLL settings.
Change-Id: Iabce4726baff493a6136136af18732b58df45d7f
Reviewed-on: https://chromium-review.googlesource.com/347551
Commit-Ready: Dino Li <Dino.Li@ite.com.tw>
Tested-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
We have a limitation for EC interrupt vector registers.
System may read incorrect interrupt number in ISR so we need to add
a workaround to prevent it.
The following is a example that got incorrect interrupt number:
1. REG IVCTx = 0x10. (no interrupt pending)
2. EC INT6 interrupt occurs (IVCTx = 0x16) and jump to ISR.
3. Read interrupt vector register to determine interrupt number.
4. Higher priority interrupt of same interrupt group occurs
(for example: INT134, IVCTx = 0x96) while the system is reading the
interrupt vector register for EC INT6, we may end up with an incorrect
interrupt number between 0x16 and 0x96.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. EC interrupts work normally: WUI (GPIO interrupt), timer, uart,
LPC, I2C, and PECI.
2. Console command 'taskinfo'.
Change-Id: I54e61f417ad506eb3b4cd5d0652f64eed9a28a17
Reviewed-on: https://chromium-review.googlesource.com/322097
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
1. Implement deep doze mode for CONFIG_LOW_POWER_IDLE.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=test the following items in deep doze mode.
1. WUI interrupts wake-up OK. (For example, power button, lid,
uart rx, keyboard ksi, and so on)
2. LPC access interrupt wake-up OK.
3. Enabled Hook debug, no warning message received (48hrs).
Change-Id: I8702a112632cb6c1c0fa75d682badf272130a7d4
Reviewed-on: https://chromium-review.googlesource.com/307060
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
[chip config]
1. No hardware specific udelay().
2. Enable watchdog.
[watchdog]
3. Watchdog period is "CONFIG_WATCHDOG_PERIOD_MS" of config.h.
4. Watchdog auxiliary timer period is "CONFIG_AUX_TIMER_PERIOD_MS".
[task and irq]
5. Write 1 to clear interrupt pending status, no |.
6. A global variable for store interrupt number of software interrupt.
[uart]
7. Always reset UART module before config it.
[hwtimer]
8. Use more external timers for HW timer module.
[task]
9. Fix task profiling.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=[watchdog]
1. console "waitms 1100", only pre-watchdog warning message.
2. console "waitms 1600", warning message and watchdog reset.
[hwtimer]
3. console commands "gettime", "timerinfo", and "forcetime".
4. enable hook debug and there is no delayed by more than 10%
warning message over 48 hours.
5. There is no watchdog reset too.
[task]
6. console 'taskinfo'
Task Ready Name Events Time (s) StkUsed
0 R << idle >> 00000000 32.927724 308/512
1 HOOKS 00000000 0.034267 372/768
2 R CONSOLE 00000000 0.116763 468/768
3 HOSTCMD 00000000 0.000641 372/512
4 KEYPROTO 00000000 0.000042 212/512
5 KEYSCAN 00000000 0.000908 356/512
IRQ counts by type:
38 2932
155 1
158 261
160 67
Service calls: 87
Total exceptions: 3348
Task switches: 167
Task switching started: 0.001999 s
Time in tasks: 33.282819 s
Time in exceptions: 0.164717 s
Change-Id: I234085cec231cd855d2a5e639ea1b0966c61d796
Reviewed-on: https://chromium-review.googlesource.com/296939
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
1. Host access to the PNPCFG registers is disabled.
2. UART2 for host if necessary.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. host can't access the PNPCFG registers.
2. out I/O port 0x2f8 '0x30, 0x31, 0x32, 0x33, and 0x34'
will have console message '01234'.
Change-Id: If07bdc129105f5248661d929e6858d4063c452ee
Reviewed-on: https://chromium-review.googlesource.com/300266
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Initial support for the ITE IT8380 chip with the following peripherals :
- 8250-like UART module.
- HW timer (with a 128-us tick period).
- GPIO with pins initialization and edge interrupt support.
other functions are stubbed.
- Clock : basic fixed frequency setup only.
It also add the dev board configuration as a test vehicle.
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:23575
TEST=make BOARD=it8380dev
on IT8380 dev board, use the EC serial console, use gettime from
console.
Change-Id: Id4bf37d1beb21d1a4bee404c9a0bc500025fe787
Reviewed-on: https://chromium-review.googlesource.com/175481
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Alec Berg <alecaberg@chromium.org>
Tested-by: Alec Berg <alecaberg@chromium.org>
