mirror of
https://github.com/Telecominfraproject/OpenCellular.git
synced 2025-12-27 18:25:05 +00:00
8a3b998868
Using the lid angle, detect if we are in tablet mode or not.
We are in tablet mode when the lid angle is large enough:
tablet_mode:
1 | +-----<----+----------
| \/ /\
| | |
0 |------------------------>----+
+------------------+----------+----------+ lid angle
0 240 300 360
BRANCH=kevin
BUG=chrome-os-partner:55702,b:27849483
TEST=Check on Kevin event are sent on tablet mode transition.
Change-Id: Id9935ce4dd717e2c20fa6c9520defb504a1760d9
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/383073
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
2423 lines
72 KiB
C
2423 lines
72 KiB
C
/* Copyright 2016 The Chromium OS Authors. All rights reserved.
|
|
* Use of this source code is governed by a BSD-style license that can be
|
|
* found in the LICENSE file.
|
|
*/
|
|
|
|
/*
|
|
* config.h - Top-level configuration Chrome EC
|
|
*
|
|
* All configuration settings (CONFIG_*) are defined in this file or in a
|
|
* sub-configuration file (config_chip.h, board.h, etc.) included by this file.
|
|
*
|
|
* Note that this file is included by assembly (.S) files. Any C-isms such as
|
|
* struct definitions or enums in a sub-configuration file MUST be guarded with
|
|
* #ifndef __ASSEMBLER__ to prevent those C-isms from being evaluated by the
|
|
* assembler.
|
|
*/
|
|
|
|
#ifndef __CROS_EC_CONFIG_H
|
|
#define __CROS_EC_CONFIG_H
|
|
|
|
/*
|
|
* All config options are listed alphabetically and described here.
|
|
*
|
|
* If you add a new config option somewhere in the code, you must add a
|
|
* default value here and describe what it does.
|
|
*
|
|
* To get a list current list, run this command:
|
|
* git grep " CONFIG_" | grep -o "CONFIG_[A-Za-z0-9_]\+" | sort | uniq
|
|
*
|
|
* Some options are #defined here to enable them by default. Chips or boards
|
|
* may override this by #undef'ing them in config_chip.h or board.h,
|
|
* respectively.
|
|
*
|
|
* TODO(crosbug.com/p/23758): Describe all of these. Also describe the
|
|
* HAS_TASK_* macro and how/when it should be used vs. a config define. And
|
|
* BOARD_*, CHIP_*, and CHIP_FAMILY_*.
|
|
*/
|
|
|
|
/* Enable accelerometer interrupts. */
|
|
#undef CONFIG_ACCEL_INTERRUPTS
|
|
/* Add support for sensor FIFO:
|
|
* define the size of the global fifo, must be a power of 2. */
|
|
#undef CONFIG_ACCEL_FIFO
|
|
/* The amount of free entries that trigger an interrupt to the AP. */
|
|
#undef CONFIG_ACCEL_FIFO_THRES
|
|
|
|
/*
|
|
* Sensors in this mask are in forced mode: they needed to be polled
|
|
* at their data rate frequency.
|
|
*/
|
|
#undef CONFIG_ACCEL_FORCE_MODE_MASK
|
|
|
|
/* Specify type of accelerometers attached. */
|
|
#undef CONFIG_ACCEL_BMA255
|
|
#undef CONFIG_ACCEL_KXCJ9
|
|
#undef CONFIG_ACCEL_KX022
|
|
#undef CONFIG_ACCELGYRO_LSM6DS0
|
|
#undef CONFIG_ACCELGYRO_BMI160
|
|
|
|
/* Specify barometer attached */
|
|
#undef CONFIG_BARO_BMP280
|
|
|
|
/*
|
|
* Use the old standard reference frame for accelerometers. The old
|
|
* reference frame is:
|
|
* Z-axis: perpendicular to keyboard, pointing up, such that if the device
|
|
* is sitting flat on a table, the accel reads +G.
|
|
* X-axis: in the plane of the keyboard, pointing from the front lip to the
|
|
* hinge, such that if the device is oriented with the front lip touching
|
|
* the table and the hinge directly above, the accel reads +G.
|
|
* Y-axis: in the plane of the keyboard, pointing to the right, such that
|
|
* if the device is on it's left side, the accel reads +G.
|
|
*
|
|
* Also, in the old reference frame, the lid accel matches the base accel
|
|
* readings when lid is closed.
|
|
*/
|
|
#undef CONFIG_ACCEL_STD_REF_FRAME_OLD
|
|
|
|
/*
|
|
* Define the event to raise when BMI160 interrupt.
|
|
* Must be within TASK_EVENT_MOTION_INTERRUPT_MASK.
|
|
*/
|
|
#undef CONFIG_ACCELGYRO_BMI160_INT_EVENT
|
|
|
|
/* Specify type of Gyrometers attached. */
|
|
#undef CONFIG_GYRO_L3GD20H
|
|
|
|
/* Compile chip support for analog-to-digital convertor */
|
|
#undef CONFIG_ADC
|
|
|
|
/*
|
|
* ADC sample time selection. The value is chip-dependent.
|
|
* TODO: Replace this with CONFIG_ADC_PROFILE entries.
|
|
*/
|
|
#undef CONFIG_ADC_SAMPLE_TIME
|
|
|
|
/* Include the ADC analog watchdog feature in the ADC code */
|
|
#define CONFIG_ADC_WATCHDOG
|
|
|
|
/*
|
|
* Chip-dependent ADC configuration - select one.
|
|
* SINGLE - Sample all inputs once when requested.
|
|
* FAST_CONTINUOUS - Sample all inputs continuously using DMA, with minimal
|
|
* sample time.
|
|
*/
|
|
#define CONFIG_ADC_PROFILE_SINGLE
|
|
#undef CONFIG_ADC_PROFILE_FAST_CONTINUOUS
|
|
|
|
/*
|
|
* Some ALS modules may be connected to the EC. We need the command, and
|
|
* specific drivers for each module.
|
|
*/
|
|
#undef CONFIG_ALS
|
|
#undef CONFIG_ALS_ISL29035
|
|
#undef CONFIG_ALS_OPT3001
|
|
/* Define the exact model ID present on the board: SI1141 = 41, SI1142 = 42, */
|
|
#undef CONFIG_ALS_SI114X
|
|
/* Check if the device revision is supported */
|
|
#undef CONFIG_ALS_SI114X_CHECK_REVISION
|
|
/*
|
|
* Define the event to raise when BMI160 interrupt.
|
|
* Must be within TASK_EVENT_MOTION_INTERRUPT_MASK.
|
|
*/
|
|
#undef CONFIG_ALS_SI114X_INT_EVENT
|
|
|
|
/* Define which ALS sensor is used for dimming the lightbar when dark */
|
|
#undef CONFIG_ALS_LIGHTBAR_DIMMING
|
|
|
|
/* Support AP hang detection host command and state machine */
|
|
#undef CONFIG_AP_HANG_DETECT
|
|
|
|
/* Support AP Warm reset Interrupt. */
|
|
#undef CONFIG_AP_WARM_RESET_INTERRUPT
|
|
|
|
/* Allow proprietary communication protocols' extensions. */
|
|
#undef CONFIG_EXTENSION_COMMAND
|
|
/*
|
|
* Support controlling the display backlight based on the state of the lid
|
|
* switch. The EC will disable the backlight when the lid is closed.
|
|
*/
|
|
#undef CONFIG_BACKLIGHT_LID
|
|
|
|
/*
|
|
* If defined, EC will enable the backlight signal only if this GPIO is
|
|
* asserted AND the lid is open. This supports passing the backlight-enable
|
|
* signal from the AP through EC.
|
|
*/
|
|
#undef CONFIG_BACKLIGHT_REQ_GPIO
|
|
|
|
/*****************************************************************************/
|
|
/* Battery config */
|
|
|
|
/* Support a simple battery. */
|
|
#undef CONFIG_BATTERY
|
|
|
|
/*
|
|
* Compile battery-specific code.
|
|
*
|
|
* Note that some boards have their own unique battery constants / functions.
|
|
* In this case, those are provided in board/(boardname)/battery.c, and none of
|
|
* these are defined.
|
|
*/
|
|
#undef CONFIG_BATTERY_BQ20Z453
|
|
#undef CONFIG_BATTERY_BQ27541
|
|
#undef CONFIG_BATTERY_BQ27621
|
|
#undef CONFIG_BATTERY_RYU
|
|
#undef CONFIG_BATTERY_SAMUS
|
|
|
|
/* Compile mock battery support; used by tests. */
|
|
#undef CONFIG_BATTERY_MOCK
|
|
|
|
/*
|
|
* Charger should call battery_override_params() to limit/correct the voltage
|
|
* and current requested by the battery pack before acting on the request.
|
|
*
|
|
* This is valid with CONFIG_CHARGER_V1 only.
|
|
*/
|
|
#undef CONFIG_BATTERY_OVERRIDE_PARAMS
|
|
|
|
/* Maximum time to wake a non-responsive battery, in second */
|
|
#define CONFIG_BATTERY_PRECHARGE_TIMEOUT 30
|
|
|
|
/*
|
|
* If defined, the charger will check for battery presence before attempting
|
|
* to communicate with it. This avoids the 30 second delay when booting
|
|
* without a battery present. Do not use with CONFIG_BATTERY_PRESENT_GPIO.
|
|
*
|
|
* Replace the default battery_is_present() function with a board-specific
|
|
* implementation in board.c
|
|
*/
|
|
#undef CONFIG_BATTERY_PRESENT_CUSTOM
|
|
|
|
/*
|
|
* If defined, GPIO which is driven low when battery is present.
|
|
* Charger will check for battery presence before attempting to communicate
|
|
* with it. This avoids the 30 second delay when booting without a battery
|
|
* present. Do not use with CONFIG_BATTERY_PRESENT_CUSTOM.
|
|
*/
|
|
#undef CONFIG_BATTERY_PRESENT_GPIO
|
|
|
|
/*
|
|
* Compile smart battery support
|
|
*
|
|
* For batteries which support this specification:
|
|
* http://sbs-forum.org/specs/sbdat110.pdf)
|
|
*/
|
|
#undef CONFIG_BATTERY_SMART
|
|
|
|
/*
|
|
* Critical battery shutdown timeout (seconds)
|
|
*
|
|
* If the battery is at extremely low charge (and discharging) or extremely
|
|
* high temperature, the EC will shut itself down. This defines the timeout
|
|
* period in seconds between the critical condition being detected and the
|
|
* EC shutting itself down. Note that if the critical condition is corrected
|
|
* before the timeout expiration, the EC will not shut itself down.
|
|
*
|
|
*/
|
|
#define CONFIG_BATTERY_CRITICAL_SHUTDOWN_TIMEOUT 30
|
|
|
|
/* Perform a battery cut-off when we reach the battery critical level */
|
|
#undef CONFIG_BATTERY_CRITICAL_SHUTDOWN_CUT_OFF
|
|
|
|
/*
|
|
* Support battery cut-off as host command and console command.
|
|
*
|
|
* Once defined, you have to implement a board_cut_off_battery() function
|
|
* in board/???/battery.c file.
|
|
*/
|
|
#undef CONFIG_BATTERY_CUT_OFF
|
|
|
|
/*
|
|
* The default delay is 1 second. Define this if a board prefers
|
|
* different delay.
|
|
*/
|
|
#undef CONFIG_BATTERY_CUTOFF_DELAY_US
|
|
|
|
/*
|
|
* The board-specific battery.c implements get and set functions to read and
|
|
* write arbirary vendor-specific parameters stored in the battery.
|
|
* See include/battery.h for prototypes.
|
|
*/
|
|
#undef CONFIG_BATTERY_VENDOR_PARAM
|
|
|
|
/*
|
|
* TODO(crosbug.com/p/29467): allows charging of a dead battery that
|
|
* requests nil for current and voltage. Remove this workaround when
|
|
* possible.
|
|
*/
|
|
#undef CONFIG_BATTERY_REQUESTS_NIL_WHEN_DEAD
|
|
|
|
/*
|
|
* Check for battery in disconnect state (similar to cut-off state). If this
|
|
* battery is found to be in disconnect state, take it out of this state by
|
|
* force-applying a charge current.
|
|
*/
|
|
#undef CONFIG_BATTERY_REVIVE_DISCONNECT
|
|
|
|
/* Include support for Bluetooth LE */
|
|
#undef CONFIG_BLUETOOTH_LE
|
|
|
|
/* Include support for testing the radio for Bluetooth LE */
|
|
#undef CONFIG_BLUETOOTH_LE_RADIO_TEST
|
|
|
|
/* Include support for the HCI and link layers for Bluetooth LE */
|
|
#undef CONFIG_BLUETOOTH_LE_STACK
|
|
|
|
/* Include debugging support for the Bluetooth link layer */
|
|
#undef CONFIG_BLUETOOTH_LL_DEBUG
|
|
|
|
/* Include debugging support for Bluetooth HCI */
|
|
#undef CONFIG_BLUETOOTH_HCI_DEBUG
|
|
|
|
/* Boot header storage offset. */
|
|
#undef CONFIG_BOOT_HEADER_STORAGE_OFF
|
|
|
|
/* Size of boot header in storage. */
|
|
#undef CONFIG_BOOT_HEADER_STORAGE_SIZE
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* EC has GPIOs to allow board to reset RTC */
|
|
#undef CONFIG_BOARD_HAS_RTC_RESET
|
|
|
|
/*
|
|
* Call board_config_post_gpio_init() after GPIOs are initialized. See
|
|
* include/board_config.h for more information.
|
|
*/
|
|
#undef CONFIG_BOARD_POST_GPIO_INIT
|
|
|
|
/*
|
|
* Call board_config_pre_init() before any inits are called. See
|
|
* include/board_config.h for more information.
|
|
*/
|
|
#undef CONFIG_BOARD_PRE_INIT
|
|
|
|
/* EC has GPIOs attached to board version stuffing resistors */
|
|
#undef CONFIG_BOARD_VERSION
|
|
/* The decoding of the GPIOs defining board version is defined in board code */
|
|
#undef CONFIG_BOARD_SPECIFIC_VERSION
|
|
|
|
/* Permanent LM4 boot configuration */
|
|
#undef CONFIG_BOOTCFG_VALUE
|
|
|
|
/*****************************************************************************/
|
|
/* Modify the default behavior to make system bringup easier. */
|
|
#undef CONFIG_BRINGUP
|
|
|
|
/*
|
|
* Enable debug prints / asserts that may helpful for debugging board bring-up,
|
|
* but probably shouldn't be enabled for production for performance reasons.
|
|
*/
|
|
#undef CONFIG_DEBUG_BRINGUP
|
|
|
|
/*****************************************************************************/
|
|
|
|
/*
|
|
* Number of extra buttons not on the keyboard scan matrix. Doesn't include
|
|
* the power button, which has its own handler.
|
|
*/
|
|
#undef CONFIG_BUTTON_COUNT
|
|
|
|
/*
|
|
* Enable case close debug (CCD) mode in the EC.
|
|
*/
|
|
#undef CONFIG_CASE_CLOSED_DEBUG
|
|
/* The case close debug (CCD) feature is provided by an external chip. */
|
|
#undef CONFIG_CASE_CLOSED_DEBUG_EXTERNAL
|
|
|
|
/*
|
|
* Capsense chip has buttons, too.
|
|
*/
|
|
#undef CONFIG_CAPSENSE
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Compile charge manager */
|
|
#undef CONFIG_CHARGE_MANAGER
|
|
|
|
/* Allow charge manager to default to charging from dual-role partners */
|
|
#undef CONFIG_CHARGE_MANAGER_DRP_CHARGING
|
|
|
|
/* Handle the external power limit host command in charge manager */
|
|
#undef CONFIG_CHARGE_MANAGER_EXTERNAL_POWER_LIMIT
|
|
|
|
/* Compile input current ramping support */
|
|
#undef CONFIG_CHARGE_RAMP
|
|
|
|
/* The hardware has some input current ramping/back-off mechanism */
|
|
#undef CONFIG_CHARGE_RAMP_HW
|
|
|
|
/*****************************************************************************/
|
|
/* Charger config */
|
|
|
|
/* Compile common charge state code. You must pick an implementation. */
|
|
#undef CONFIG_CHARGER
|
|
#undef CONFIG_CHARGER_V1
|
|
#undef CONFIG_CHARGER_V2
|
|
|
|
/* Compile charger-specific code for these chargers (pick at most one) */
|
|
#undef CONFIG_CHARGER_BD99955
|
|
#undef CONFIG_CHARGER_BQ24707A
|
|
#undef CONFIG_CHARGER_BQ24715
|
|
#undef CONFIG_CHARGER_BQ24725
|
|
#undef CONFIG_CHARGER_BQ24735
|
|
#undef CONFIG_CHARGER_BQ24738
|
|
#undef CONFIG_CHARGER_BQ24770
|
|
#undef CONFIG_CHARGER_BQ24773
|
|
#undef CONFIG_CHARGER_BQ25890
|
|
#undef CONFIG_CHARGER_BQ25892
|
|
#undef CONFIG_CHARGER_BQ25895
|
|
#undef CONFIG_CHARGER_ISL9237
|
|
#undef CONFIG_CHARGER_TPS65090 /* Note: does not use CONFIG_CHARGER */
|
|
|
|
/*
|
|
* BD99955 PD port to charger port mapping.
|
|
* By default VBUS is selected as primary port.
|
|
* Define only if the VCC is the primary port.
|
|
*/
|
|
#undef CONFIG_BD99955_PRIMARY_CHARGE_PORT_VCC
|
|
|
|
/*
|
|
* If the battery temperature sense pin is connected to charger,
|
|
* get the battery temperature from the charger.
|
|
*/
|
|
#undef CONFIG_CHARGER_BATTERY_TSENSE
|
|
|
|
/*
|
|
* BQ2589x IR Compensation settings.
|
|
* Should be the combination of BQ2589X_IR_TREG_xxxC, BQ2589X_IR_VCLAMP_yyyMV
|
|
* and BQ2589X_IR_BAT_COMP_zzzMOHM.
|
|
*/
|
|
#undef CONFIG_CHARGER_BQ2589X_IR_COMP
|
|
/*
|
|
* BQ2589x 5V boost current limit and voltage.
|
|
* Should be the combination of BQ2589X_BOOSTV_MV(voltage) and
|
|
* BQ2589X_BOOST_LIM_xxxMA.
|
|
*/
|
|
#undef CONFIG_CHARGER_BQ2589X_BOOST
|
|
|
|
/*
|
|
* Board specific charging current limit, in mA. If defined, the charge state
|
|
* machine will not allow the battery to request more current than this.
|
|
*/
|
|
#undef CONFIG_CHARGER_CURRENT_LIMIT
|
|
|
|
/* Enable/disable system power monitor PSYS function */
|
|
#undef CONFIG_CHARGER_PSYS
|
|
|
|
/*
|
|
* Board specific charging current termination limit, in mA. If defined and
|
|
* charger supports setting termination current it should be set during charger
|
|
* init.
|
|
*
|
|
* TODO(tbroch): Only valid for bq2589x currently. Configure defaults for other
|
|
* charger ICs that support termination currents.
|
|
*/
|
|
#undef CONFIG_CHARGER_TERM_CURRENT_LIMIT
|
|
|
|
/*
|
|
* Board supports discharge mode. In this mode, the battery will discharge
|
|
* even if AC is present. Used for testing.
|
|
*/
|
|
#undef CONFIG_CHARGER_DISCHARGE_ON_AC
|
|
|
|
/* Board has a custom discharge mode. */
|
|
#undef CONFIG_CHARGER_DISCHARGE_ON_AC_CUSTOM
|
|
|
|
/*
|
|
* Board specific flag used to disable external ILIM pin used to determine input
|
|
* current limit. When defined, the input current limit is decided only by
|
|
* the software register value.
|
|
*/
|
|
#undef CONFIG_CHARGER_ILIM_PIN_DISABLED
|
|
|
|
/*
|
|
* Default input current for the board, in mA.
|
|
*
|
|
* This value should depend on external power adapter, designed charging
|
|
* voltage, and the maximum power of the running system. For type-C chargers,
|
|
* this should be set to 512 mA in order to not brown-out low-current USB
|
|
* charge ports.
|
|
*/
|
|
#undef CONFIG_CHARGER_INPUT_CURRENT
|
|
|
|
/*
|
|
* Board specific maximum input current limit, in mA.
|
|
*/
|
|
#undef CONFIG_CHARGER_MAX_INPUT_CURRENT
|
|
|
|
/* Minimum battery percentage for power on */
|
|
#undef CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON
|
|
|
|
/* Narrow VDC power path */
|
|
#undef CONFIG_CHARGER_NARROW_VDC
|
|
|
|
/*
|
|
* Low energy thresholds - when battery level is below BAT_PCT and an external
|
|
* charger provides less than CHG_MW of power, inform the AP of the situation
|
|
* through the LIMIT_POWER host event.
|
|
*/
|
|
#undef CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT
|
|
#undef CONFIG_CHARGER_LIMIT_POWER_THRESH_CHG_MW
|
|
|
|
/*
|
|
* Equivalent of CONFIG_BATTERY_OVERRIDE_PARAMS for use with
|
|
* CONFIG_CHARGER_V2
|
|
*/
|
|
#undef CONFIG_CHARGER_PROFILE_OVERRIDE
|
|
|
|
/* Value of the charge sense resistor, in mOhms */
|
|
#undef CONFIG_CHARGER_SENSE_RESISTOR
|
|
|
|
/* Value of the input current sense resistor, in mOhms */
|
|
#undef CONFIG_CHARGER_SENSE_RESISTOR_AC
|
|
|
|
/*
|
|
* Maximum time to charge the battery, in hours.
|
|
*
|
|
* If this timeout is reached, the charger will enter force-idle state.
|
|
* If not defined, charger will provide current until the battery asks it to
|
|
* stop.
|
|
*/
|
|
#undef CONFIG_CHARGER_TIMEOUT_HOURS
|
|
|
|
/*
|
|
* Board has an GPIO pin to enable or disable charging.
|
|
*
|
|
* This GPIO should be named GPIO_CHARGER_EN, if active high. Or
|
|
* GPIO_CHARGER_EN_L if active low.
|
|
*/
|
|
#undef CONFIG_CHARGER_EN_GPIO
|
|
|
|
/* Charger enable GPIO is active low */
|
|
#undef CONFIG_CHARGER_EN_ACTIVE_LOW
|
|
|
|
/* Enable trickle charging */
|
|
#undef CONFIG_TRICKLE_CHARGING
|
|
|
|
/*****************************************************************************/
|
|
/* Chipset config */
|
|
|
|
/* AP chipset support; pick at most one */
|
|
#undef CONFIG_CHIPSET_APOLLOLAKE/* Intel Apollolake (x86) */
|
|
#undef CONFIG_CHIPSET_BAYTRAIL /* Intel Bay Trail (x86) */
|
|
#undef CONFIG_CHIPSET_BRASWELL /* Intel Braswell (x86) */
|
|
#undef CONFIG_CHIPSET_ECDRIVEN /* Dummy power module */
|
|
#undef CONFIG_CHIPSET_GAIA /* Gaia and Ares (ARM) */
|
|
#undef CONFIG_CHIPSET_HASWELL /* Intel Haswell (x86) */
|
|
#undef CONFIG_CHIPSET_MEDIATEK /* MediaTek MT81xx */
|
|
#undef CONFIG_CHIPSET_RK3399 /* Rockchip rk3399 */
|
|
/* TODO: Rename below config to CONFIG_CHIPSET_RK32XX */
|
|
#undef CONFIG_CHIPSET_ROCKCHIP /* Rockchip rk32xx */
|
|
#undef CONFIG_CHIPSET_SKYLAKE /* Intel Skylake (x86) */
|
|
#undef CONFIG_CHIPSET_TEGRA /* nVidia Tegra 5 */
|
|
|
|
/* Support chipset throttling */
|
|
#undef CONFIG_CHIPSET_CAN_THROTTLE
|
|
|
|
/* Enable additional chipset debugging */
|
|
#undef CONFIG_CHIPSET_DEBUG
|
|
|
|
/* Enable chipset reset hook, requires a deferrable function */
|
|
#undef CONFIG_CHIPSET_RESET_HOOK
|
|
|
|
/* Support power rail control */
|
|
#define CONFIG_CHIPSET_HAS_PP1350
|
|
#define CONFIG_CHIPSET_HAS_PP5000
|
|
|
|
/*****************************************************************************/
|
|
/*
|
|
* Chip config for clock circuitry
|
|
* define = crystal / undef = oscillator
|
|
*/
|
|
#undef CONFIG_CLOCK_CRYSTAL
|
|
|
|
/* Indicate if a clock source is connected to stm32f4's "HSE" specific input */
|
|
#undef CONFIG_STM32_CLOCK_HSE_HZ
|
|
|
|
/*****************************************************************************/
|
|
/* PMIC config */
|
|
|
|
/* Support firmware long press power-off timer */
|
|
#undef CONFIG_PMIC_FW_LONG_PRESS_TIMER
|
|
|
|
/* Support PMIC power control */
|
|
#undef CONFIG_PMIC
|
|
|
|
/*****************************************************************************/
|
|
/*
|
|
* Optional console commands
|
|
*
|
|
* Defining these options will enable the corresponding command on the EC
|
|
* console.
|
|
*/
|
|
|
|
#undef CONFIG_CMD_ACCELS
|
|
#undef CONFIG_CMD_ACCEL_INFO
|
|
#undef CONFIG_CMD_ALS
|
|
#define CONFIG_CMD_APTHROTTLE
|
|
#undef CONFIG_CMD_BATDEBUG
|
|
#define CONFIG_CMD_BATTFAKE
|
|
#undef CONFIG_CMD_BUTTON
|
|
#define CONFIG_CMD_CHARGER
|
|
#undef CONFIG_CMD_CHARGER_ADC_AMON_BMON
|
|
#undef CONFIG_CMD_CHARGER_PSYS
|
|
#define CONFIG_CMD_CHARGE_SUPPLIER_INFO
|
|
#undef CONFIG_CMD_CHGRAMP
|
|
#undef CONFIG_CMD_CLOCKGATES
|
|
#undef CONFIG_CMD_COMXTEST
|
|
#define CONFIG_CMD_CRASH
|
|
#undef CONFIG_CMD_ECTEMP
|
|
#define CONFIG_CMD_FASTCHARGE
|
|
#undef CONFIG_CMD_FLASH
|
|
#undef CONFIG_CMD_FORCETIME
|
|
#undef CONFIG_CMD_GSV
|
|
#undef CONFIG_CMD_GPIO_EXTENDED
|
|
#define CONFIG_CMD_HASH
|
|
#define CONFIG_CMD_HCDEBUG
|
|
#undef CONFIG_CMD_HOSTCMD
|
|
#undef CONFIG_CMD_I2C_PROTECT
|
|
#define CONFIG_CMD_I2C_SCAN
|
|
#define CONFIG_CMD_I2C_XFER
|
|
#undef CONFIG_CMD_I2CWEDGE
|
|
#define CONFIG_CMD_IDLE_STATS
|
|
#define CONFIG_CMD_KEYBOARD
|
|
#undef CONFIG_CMD_ILIM
|
|
#define CONFIG_CMD_INA
|
|
#define CONFIG_CMD_REGULATOR
|
|
#undef CONFIG_CMD_RTC
|
|
#undef CONFIG_CMD_JUMPTAGS
|
|
#undef CONFIG_CMD_LID_ANGLE
|
|
#undef CONFIG_CMD_MCDP
|
|
#define CONFIG_CMD_MD
|
|
#define CONFIG_CMD_MEM
|
|
#define CONFIG_CMD_PD
|
|
#undef CONFIG_CMD_PD_CONTROL
|
|
#undef CONFIG_CMD_PD_DEV_DUMP_INFO
|
|
#undef CONFIG_CMD_PD_FLASH
|
|
#undef CONFIG_CMD_PLL
|
|
#undef CONFIG_CMD_PMU
|
|
#define CONFIG_CMD_POWER_AP
|
|
#define CONFIG_CMD_POWERINDEBUG
|
|
#undef CONFIG_CMD_POWERLED
|
|
#undef CONFIG_CMD_RTC_ALARM
|
|
#undef CONFIG_CMD_SCRATCHPAD
|
|
#define CONFIG_CMD_SHMEM
|
|
#undef CONFIG_CMD_SLEEP
|
|
#undef CONFIG_CMD_SPI_FLASH
|
|
#undef CONFIG_CMD_SPI_NOR
|
|
#undef CONFIG_CMD_SPI_XFER
|
|
#undef CONFIG_CMD_STACKOVERFLOW
|
|
#undef CONFIG_CMD_TASKREADY
|
|
#define CONFIG_CMD_TEMP_SENSOR
|
|
#define CONFIG_CMD_TIMERINFO
|
|
#define CONFIG_CMD_TYPEC
|
|
#undef CONFIG_CMD_USART_INFO
|
|
#undef CONFIG_CMD_USB_PD_PE
|
|
#define CONFIG_CMD_USBMUX
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Provide common core code to output panic information without interrupts. */
|
|
#define CONFIG_COMMON_PANIC_OUTPUT
|
|
|
|
/*
|
|
* Store a panic log and halt the system for a software-related reasons, such as
|
|
* stack overflow or assertion failure.
|
|
*/
|
|
#undef CONFIG_SOFTWARE_PANIC
|
|
|
|
/*
|
|
* Provide the default GPIO abstraction layer.
|
|
* You want this unless you are doing a really tiny firmware.
|
|
*/
|
|
#define CONFIG_COMMON_GPIO
|
|
|
|
/*
|
|
* Provides smaller GPIO names to reduce flash size. Instead of the 'name'
|
|
* field in GPIO macro it will concat 'port' and 'pin' to reduce flash size.
|
|
*/
|
|
#undef CONFIG_COMMON_GPIO_SHORTNAMES
|
|
|
|
/*
|
|
* Provide common runtime layer code (tasks, hooks ...)
|
|
* You want this unless you are doing a really tiny firmware.
|
|
*/
|
|
#define CONFIG_COMMON_RUNTIME
|
|
|
|
/* Provide common core code to handle the operating system timers. */
|
|
#define CONFIG_COMMON_TIMER
|
|
|
|
/*****************************************************************************/
|
|
|
|
/*
|
|
* Provide additional help on console commands, such as the supported
|
|
* options/usage.
|
|
*
|
|
* Boards may #undef this to reduce image size.
|
|
*/
|
|
#define CONFIG_CONSOLE_CMDHELP
|
|
|
|
/*
|
|
* Add a .flags field to the console commands data structure, to distinguish
|
|
* some commands from others. The available flags bits are defined in
|
|
* include/console.h
|
|
*/
|
|
#undef CONFIG_CONSOLE_COMMAND_FLAGS
|
|
|
|
/*
|
|
* One use of the .flags field is to make some console commands restricted, so
|
|
* that they can be disabled or enabled at run time.
|
|
*/
|
|
#undef CONFIG_RESTRICTED_CONSOLE_COMMANDS
|
|
|
|
/* The default .flags field value is zero, unless overridden with this. */
|
|
#undef CONFIG_CONSOLE_COMMAND_FLAGS_DEFAULT
|
|
|
|
/*
|
|
* Number of entries in console history buffer.
|
|
*
|
|
* Boards may #undef this to reduce memory usage.
|
|
*/
|
|
#define CONFIG_CONSOLE_HISTORY 8
|
|
|
|
/* Max length of a single line of input */
|
|
#define CONFIG_CONSOLE_INPUT_LINE_SIZE 80
|
|
|
|
/*
|
|
* Enable the experimental console.
|
|
*
|
|
* NOTE: If you enable this experimental console, you will need to run the
|
|
* EC-3PO interactive console in the util directory! Otherwise, you won't be
|
|
* able to enter any commands.
|
|
*/
|
|
#undef CONFIG_EXPERIMENTAL_CONSOLE
|
|
|
|
/* Include CRC-8 utility function */
|
|
#undef CONFIG_CRC8
|
|
|
|
/*
|
|
* When enabled, do not build RO image from the same set of files as the RW
|
|
* image. Instead define a separate set of object files in the respective
|
|
* build.mk files by adding the objects to the custom-ro_objs-y variable.
|
|
*/
|
|
#undef CONFIG_CUSTOMIZED_RO
|
|
|
|
/*
|
|
* When enabled, build in support for software & hardware crypto;
|
|
* only supported on CR50.
|
|
*/
|
|
#undef CONFIG_DCRYPTO
|
|
|
|
/*****************************************************************************/
|
|
/*
|
|
* Debugging config
|
|
*
|
|
* Note that these options are enabled by default, because they're really
|
|
* handy for debugging systems during bringup and even at factory time.
|
|
*
|
|
* A board may undefine any or all of these to reduce image size and RAM usage,
|
|
* at the cost of debuggability.
|
|
*/
|
|
|
|
/*
|
|
* ASSERT() macros are checked at runtime. See CONFIG_DEBUG_ASSERT_REBOOTS
|
|
* to see what happens if one fails.
|
|
*
|
|
* Boards may #undef this to reduce image size.
|
|
*/
|
|
#define CONFIG_DEBUG_ASSERT
|
|
|
|
/*
|
|
* Prints a message and reboots if an ASSERT() macro fails at runtime. When
|
|
* enabled, an ASSERT() which fails will produce a message of the form:
|
|
*
|
|
* ASSERTION FAILURE '<expr>' in function() at file:line
|
|
*
|
|
* If this is not defined, failing ASSERT() will trigger a BKPT instruction
|
|
* instead.
|
|
*
|
|
* Ignored if CONFIG_DEBUG_ASSERT is not defined.
|
|
*
|
|
* Boards may #undef this to reduce image size.
|
|
*/
|
|
#define CONFIG_DEBUG_ASSERT_REBOOTS
|
|
|
|
/*
|
|
* On assertion failure, prints only the file name and the line number.
|
|
*
|
|
* Ignored if CONFIG_DEBUG_ASSERT_REBOOTS is not defined.
|
|
*
|
|
* Boards may define this to reduce image size.
|
|
*/
|
|
#undef CONFIG_DEBUG_ASSERT_BRIEF
|
|
|
|
/*
|
|
* Disable the write buffer used for default memory map accesses.
|
|
* This turns "Imprecise data bus errors" into "Precise" errors
|
|
* in exception traces at the cost of some performance.
|
|
* This may help identify the offending instruction causing an
|
|
* exception. Supported on cortex-m.
|
|
*/
|
|
#undef CONFIG_DEBUG_DISABLE_WRITE_BUFFER
|
|
|
|
/*
|
|
* Print additional information when exceptions are triggered, such as the
|
|
* fault address, here shown as bfar. This shows the reason for the fault
|
|
* and may help to determine the cause.
|
|
*
|
|
* === EXCEPTION: 03 ====== xPSR: 01000000 ===========
|
|
* r0 :0000000b r1 :00000047 r2 :60000000 r3 :200013dd
|
|
* r4 :00000000 r5 :080053f4 r6 :200013d0 r7 :00000002
|
|
* r8 :00000000 r9 :200013de r10:00000000 r11:00000000
|
|
* r12:00000000 sp :200009a0 lr :08002b85 pc :08003a8a
|
|
* Precise data bus error, Forced hard fault, Vector catch, bfar = 60000000
|
|
* mmfs = 00008200, shcsr = 00000000, hfsr = 40000000, dfsr = 00000008
|
|
*
|
|
* If this is not defined, only a register dump will be printed.
|
|
*
|
|
* Boards may #undef this to reduce image size.
|
|
*/
|
|
#define CONFIG_DEBUG_EXCEPTIONS
|
|
|
|
/* Support Synchronous UART debug printf. */
|
|
#undef CONFIG_DEBUG_PRINTF
|
|
|
|
/* Check for stack overflows on every context switch */
|
|
#define CONFIG_DEBUG_STACK_OVERFLOW
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Monitor the states of other devices */
|
|
#undef CONFIG_DEVICE_STATE
|
|
|
|
/* Support DMA transfers inside the EC */
|
|
#undef CONFIG_DMA
|
|
|
|
/* Use the common interrupt handlers for DMA IRQs */
|
|
#define CONFIG_DMA_DEFAULT_HANDLERS
|
|
|
|
/* Compile extra debugging and tests for the DMA module */
|
|
#undef CONFIG_DMA_HELP
|
|
|
|
/* Support EC to Internal bus bridge. */
|
|
#undef CONFIG_EC2I
|
|
|
|
/* Support EC chip internal data EEPROM */
|
|
#undef CONFIG_EEPROM
|
|
|
|
/* Include code for handling external power */
|
|
#define CONFIG_EXTPOWER
|
|
|
|
/* Support detecting external power presence via a GPIO */
|
|
#undef CONFIG_EXTPOWER_GPIO
|
|
|
|
/* Default debounce time for external power signal */
|
|
#define CONFIG_EXTPOWER_DEBOUNCE_MS 30
|
|
|
|
/*****************************************************************************/
|
|
/* Number of cooling fans. Undef if none. */
|
|
#undef CONFIG_FANS
|
|
|
|
/* Support fan control while in low-power idle */
|
|
#undef CONFIG_FAN_DSLEEP
|
|
|
|
/*
|
|
* Replace the default fan_percent_to_rpm() function with a board-specific
|
|
* implementation in board.c
|
|
*/
|
|
#undef CONFIG_FAN_RPM_CUSTOM
|
|
|
|
/*
|
|
* We normally check and update the fans once per second (HOOK_SECOND). If this
|
|
* is #defined to a postive integer N, we will only update the fans every N
|
|
* seconds instead.
|
|
*/
|
|
#undef CONFIG_FAN_UPDATE_PERIOD
|
|
|
|
/* Send event when mode change, host read acpi memory and select DPTF table */
|
|
#undef CONFIG_DPTF_DEVICE_ORIENTATION
|
|
|
|
/*****************************************************************************/
|
|
/* Flash configuration */
|
|
|
|
/* Support programming on-chip flash */
|
|
#define CONFIG_FLASH
|
|
|
|
#undef CONFIG_FLASH_BANK_SIZE
|
|
#undef CONFIG_FLASH_ERASED_VALUE32
|
|
#undef CONFIG_FLASH_ERASE_SIZE
|
|
#undef CONFIG_FLASH_ROW_SIZE
|
|
|
|
/* Base address of program memory */
|
|
#undef CONFIG_PROGRAM_MEMORY_BASE
|
|
|
|
/*
|
|
* EC code can reside on internal or external storage. Only one of these
|
|
* CONFIGs should be defined.
|
|
*/
|
|
#undef CONFIG_EXTERNAL_STORAGE
|
|
#undef CONFIG_INTERNAL_STORAGE
|
|
|
|
/*
|
|
* Flash is directly mapped into the EC's address space. If this is not
|
|
* defined, the flash driver must implement flash_physical_read().
|
|
*/
|
|
#define CONFIG_MAPPED_STORAGE
|
|
|
|
/*
|
|
* Base address of memory-mapped flash storage, for platforms which define
|
|
* CONFIG_MAPPED_STORAGE.
|
|
*/
|
|
#undef CONFIG_MAPPED_STORAGE_BASE
|
|
|
|
#undef CONFIG_FLASH_PROTECT_NEXT_BOOT
|
|
|
|
/*
|
|
* Store persistent write protect for the flash inside the flash data itself.
|
|
* This allows ECs with internal flash to emulate something closer to a SPI
|
|
* flash write protect register. If this is not defined, write protect state
|
|
* is maintained solely by the physical flash driver.
|
|
*/
|
|
#define CONFIG_FLASH_PSTATE
|
|
|
|
/*
|
|
* Store the pstate data in its own dedicated bank of flash. This allows
|
|
* disabling the protect-RO-at-boot flag without rewriting the RO firmware,
|
|
* but costs a bank of flash.
|
|
*
|
|
* If this is not defined, the pstate data is stored inside the RO firmware
|
|
* image itself. This is more space-efficient, but the only way to clear the
|
|
* flag once it's set is to rewrite the RO firmware (after removing the WP
|
|
* screw, of course).
|
|
*/
|
|
#define CONFIG_FLASH_PSTATE_BANK
|
|
|
|
/* Total size of writable flash */
|
|
#undef CONFIG_FLASH_SIZE
|
|
|
|
/* Minimum flash write size (in bytes) */
|
|
#undef CONFIG_FLASH_WRITE_SIZE
|
|
/* Most efficient flash write size (in bytes) */
|
|
#undef CONFIG_FLASH_WRITE_IDEAL_SIZE
|
|
|
|
/* Protected region of storage belonging to EC */
|
|
#undef CONFIG_EC_PROTECTED_STORAGE_OFF
|
|
#undef CONFIG_EC_PROTECTED_STORAGE_SIZE
|
|
|
|
/* Writable region of storage belonging to EC */
|
|
#undef CONFIG_EC_WRITABLE_STORAGE_OFF
|
|
#undef CONFIG_EC_WRITABLE_STORAGE_SIZE
|
|
|
|
/*****************************************************************************/
|
|
/* NvMem Configuration */
|
|
/* Enable NV Memory module within flash */
|
|
#undef CONFIG_FLASH_NVMEM
|
|
/* Offset to start of NvMem area from base of flash */
|
|
#undef CONFIG_FLASH_NVMEM_OFFSET_A
|
|
#undef CONFIG_FLASH_NVMEM_OFFSET_B
|
|
/* Address of start of Nvmem area */
|
|
#undef CONFIG_FLASH_NVMEM_BASE_A
|
|
#undef CONFIG_FLASH_NVMEM_BASE_B
|
|
/* Size in bytes of NvMem area */
|
|
#undef CONFIG_FLASH_NVMEM_SIZE
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Include a flashmap in the compiled firmware image */
|
|
#define CONFIG_FMAP
|
|
|
|
/* Allow EC serial console input to wake up the EC from STOP mode */
|
|
#undef CONFIG_FORCE_CONSOLE_RESUME
|
|
|
|
/* Enable support for floating point unit */
|
|
#undef CONFIG_FPU
|
|
|
|
/*****************************************************************************/
|
|
/* Firmware region configuration */
|
|
|
|
#undef CONFIG_FW_PSTATE_OFF
|
|
#undef CONFIG_FW_PSTATE_SIZE
|
|
|
|
/*
|
|
* Reuse the space that was occupied in RAM by the little firmware (LFW) loader
|
|
* with the section ".bss.slow" instead.
|
|
*/
|
|
#undef CONFIG_REPLACE_LOADER_WITH_BSS_SLOW
|
|
|
|
/*
|
|
* Read-only / read-write image configuration.
|
|
* Images may reside on storage (ex. external or internal SPI) at a different
|
|
* offset than when copied to program memory. Hence, two sets of offsets,
|
|
* for STORAGE and for MEMORY.
|
|
*/
|
|
#undef CONFIG_RO_MEM_OFF
|
|
/* Offset relative to CONFIG_EC_PROTECTED_STORAGE_OFF */
|
|
#undef CONFIG_RO_STORAGE_OFF
|
|
#undef CONFIG_RO_SIZE
|
|
|
|
#undef CONFIG_RW_MEM_OFF
|
|
/* Some targets include two RW sections in the image. */
|
|
#undef CONFIG_RW_B
|
|
/* This is the offset of the second RW section into the flash. */
|
|
#undef CONFIG_RW_B_MEM_OFF
|
|
|
|
/* Offset relative to CONFIG_EC_WRITABLE_STORAGE_OFF */
|
|
#undef CONFIG_RW_STORAGE_OFF
|
|
#undef CONFIG_RW_SIZE
|
|
|
|
/*
|
|
* NPCX-specific bootheader geometry.
|
|
* TODO(crosbug.com/p/23796): Factor these CONFIGs out.
|
|
*/
|
|
#undef CONFIG_RO_HDR_MEM_OFF
|
|
#undef CONFIG_RO_HDR_SIZE
|
|
|
|
/*
|
|
* Write protect region offset / size. This region normally encompasses the
|
|
* RO image, but may also contain additional images or data.
|
|
*/
|
|
#undef CONFIG_WP_STORAGE_OFF
|
|
#undef CONFIG_WP_STORAGE_SIZE
|
|
|
|
/*
|
|
* Board Image ec.bin contains a RO firmware. If not defined, the image will
|
|
* only contain the RW firmware. The RO firmware comes from another board.
|
|
*/
|
|
#define CONFIG_FW_INCLUDE_RO
|
|
|
|
/* If defined, another image (RW) exists with more features */
|
|
#undef CONFIG_FW_LIMITED_IMAGE
|
|
|
|
/*
|
|
* If defined, we can use system_get_fw_reset_vector function to decide
|
|
* reset vector of RO/RW firmware for sysjump.
|
|
*/
|
|
#undef CONFIG_FW_RESET_VECTOR
|
|
|
|
/*****************************************************************************/
|
|
/* Motion sensor based gesture recognition information */
|
|
/* These all require HAS_TASK_MOTIONSENSE to work */
|
|
|
|
/* Do we want to detect gestures? */
|
|
#undef CONFIG_GESTURE_DETECTION
|
|
|
|
/* Mask of all sensors used for gesture dectections */
|
|
#undef CONFIG_GESTURE_DETECTION_MASK
|
|
|
|
/* some gesture recognition done in software */
|
|
#undef CONFIG_GESTURE_SW_DETECTION
|
|
|
|
/* enable gesture host interface */
|
|
#undef CONFIG_GESTURE_HOST_DETECTION
|
|
/* Sensor sampling interval for gesture recognition */
|
|
#undef CONFIG_GESTURE_SAMPLING_INTERVAL_MS
|
|
|
|
/* Which sensor to look for battery tap recognition */
|
|
#undef CONFIG_GESTURE_SENSOR_BATTERY_TAP
|
|
|
|
/*
|
|
* Double tap detection parameters
|
|
* Double tap works by looking for two isolated Z-axis accelerometer impulses
|
|
* preceded and followed by relatively calm periods of accelerometer motion.
|
|
*
|
|
* Define an outer and inner window. The inner window specifies how
|
|
* long the tap impulse is expected to last. The outer window specifies the
|
|
* period before the initial tap impluse and after the final tap impulse for
|
|
* which to check for relatively calm periods. In between the two impulses
|
|
* there is a minimum and maximum interstice time allowed.
|
|
*
|
|
* Define an acceleration threshold to dectect a tap, in mg.
|
|
*/
|
|
#undef CONFIG_GESTURE_TAP_OUTER_WINDOW_T
|
|
#undef CONFIG_GESTURE_TAP_INNER_WINDOW_T
|
|
#undef CONFIG_GESTURE_TAP_MIN_INTERSTICE_T
|
|
#undef CONFIG_GESTURE_TAP_MAX_INTERSTICE_T
|
|
#undef CONFIG_GESTURE_TAP_THRES_MG
|
|
|
|
/* Event generated when battery tap is detected */
|
|
#undef CONFIG_GESTURE_TAP_EVENT
|
|
|
|
/* Which sensor to look for significant motion activity */
|
|
#undef CONFIG_GESTURE_SIGMO
|
|
|
|
/*
|
|
* Significant motion parameters
|
|
* Sigmo state machine looks for movement, waits skip milli-seconds,
|
|
* and check for movement again with proof milli-seconds.
|
|
*/
|
|
#undef CONFIG_GESTURE_SIGMO_PROOF_MS
|
|
#undef CONFIG_GESTURE_SIGMO_SKIP_MS
|
|
#undef CONFIG_GESTURE_SIGMO_THRES_MG
|
|
/* Event generated when significant motion is detected. */
|
|
|
|
#undef CONFIG_GESTURE_SIGMO_EVENT
|
|
|
|
|
|
/* Do we want to detect the lid angle? */
|
|
#undef CONFIG_LID_ANGLE
|
|
|
|
/*
|
|
* Add code for preventing 0 and 360 degree transition. Needed when
|
|
* Device supports tablet mode.
|
|
*/
|
|
#undef CONFIG_LID_ANGLE_INVALID_CHECK
|
|
|
|
/*
|
|
* Use lid angle to detect tablet mode.
|
|
*/
|
|
#undef CONFIG_LID_ANGLE_TABLET_MODE
|
|
|
|
/* Which sensor is located on the base? */
|
|
#undef CONFIG_LID_ANGLE_SENSOR_BASE
|
|
/* Which sensor is located on the lid? */
|
|
#undef CONFIG_LID_ANGLE_SENSOR_LID
|
|
/*
|
|
* Allows using the lid angle measurement to determine if peripheral devices
|
|
* should be enabled or disabled, like key scanning, trackpad interrupt.
|
|
*/
|
|
#undef CONFIG_LID_ANGLE_UPDATE
|
|
|
|
/******************************************************************************/
|
|
/* Host to RAM (H2RAM) Memory Mapping */
|
|
|
|
/* H2RAM Base memory address */
|
|
#undef CONFIG_H2RAM_BASE
|
|
|
|
/* H2RAM Size */
|
|
#undef CONFIG_H2RAM_SIZE
|
|
|
|
/* H2RAM Host LPC I/O base memory address */
|
|
#undef CONFIG_H2RAM_HOST_LPC_IO_BASE
|
|
|
|
/*
|
|
* Define the minimal amount of time (in ms) betwen running motion sense task
|
|
* loop.
|
|
*/
|
|
#define CONFIG_MOTION_MIN_SENSE_WAIT_TIME 3
|
|
|
|
/*****************************************************************************/
|
|
/*
|
|
* Support the host asking the EC about the status of the most recent host
|
|
* command.
|
|
*
|
|
* When the AP is attached to the EC via a serialized bus such as I2C or SPI,
|
|
* it needs a way to minimize the length of time an EC command will tie up the
|
|
* bus (and the kernel driver on the AP). If this config is defined, the EC
|
|
* may return an in-progress result code for slow commands such as flash
|
|
* erase/write instead of stalling until the command finishes processing, and
|
|
* the AP may then inquire the status of the current command and/or the result
|
|
* of the previous command.
|
|
*/
|
|
#undef CONFIG_HOST_COMMAND_STATUS
|
|
|
|
/* Default hcdebug mode, e.g. HCDEBUG_OFF or HCDEBUG_NORMAL */
|
|
#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_NORMAL
|
|
|
|
/* If we have host command task, assume we also are using host events. */
|
|
#ifdef HAS_TASK_HOSTCMD
|
|
#define CONFIG_HOSTCMD_EVENTS
|
|
#else
|
|
#undef CONFIG_HOSTCMD_EVENTS
|
|
#endif
|
|
|
|
/*
|
|
* For ECs where the host command interface is I2C, slave
|
|
* address which the EC will respond to.
|
|
*/
|
|
#undef CONFIG_HOSTCMD_I2C_SLAVE_ADDR
|
|
|
|
/*
|
|
* Accept EC host commands over the SPI slave (SPS) interface.
|
|
*/
|
|
#undef CONFIG_HOSTCMD_SPS
|
|
|
|
/*
|
|
* Host command rate limiting assures EC will have time to process lower
|
|
* priority tasks even if the AP is hammering the EC with host commands.
|
|
* If there is less than CONFIG_HOSTCMD_RATE_LIMITING_MIN_REST between
|
|
* host commands for CONFIG_HOSTCMD_RATE_LIMITING_PERIOD, then a
|
|
* recess period of CONFIG_HOSTCMD_RATE_LIMITING_RECESS will be
|
|
* enforced.
|
|
*/
|
|
#define CONFIG_HOSTCMD_RATE_LIMITING_PERIOD (500 * MSEC)
|
|
#define CONFIG_HOSTCMD_RATE_LIMITING_MIN_REST (3 * MSEC)
|
|
#define CONFIG_HOSTCMD_RATE_LIMITING_RECESS (20 * MSEC)
|
|
|
|
/* PD MCU supports host commands */
|
|
#undef CONFIG_HOSTCMD_PD
|
|
|
|
/*
|
|
* Use if PD MCU controls charging (selecting charging port and input
|
|
* current limit).
|
|
*/
|
|
#undef CONFIG_HOSTCMD_PD_CHG_CTRL
|
|
|
|
/* Panic when status of PD MCU reflects that it has crashed */
|
|
#undef CONFIG_HOSTCMD_PD_PANIC
|
|
|
|
/* Board supports RTC host commands*/
|
|
#undef CONFIG_HOSTCMD_RTC
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Enable debugging and profiling statistics for hook functions */
|
|
#undef CONFIG_HOOK_DEBUG
|
|
|
|
/*****************************************************************************/
|
|
/* CRC configuration */
|
|
|
|
/* Enable the hardware accelerator for CRC computation */
|
|
#undef CONFIG_HW_CRC
|
|
|
|
/* Enable the software routine for CRC computation */
|
|
#undef CONFIG_SW_CRC
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Enable system hibernate */
|
|
#define CONFIG_HIBERNATE
|
|
|
|
/* Default delay after shutting down before hibernating */
|
|
#define CONFIG_HIBERNATE_DELAY_SEC 3600
|
|
|
|
/*
|
|
* Use to define going in to hibernate early if low on battery.
|
|
* CONFIG_HIBERNATE_BATT_PCT specifies the low battery threshold
|
|
* for going into hibernate early, and CONFIG_HIBERNATE_BATT_SEC defines
|
|
* the minimum amount of time to stay in G3 before checking for low
|
|
* battery hibernate.
|
|
*/
|
|
#undef CONFIG_HIBERNATE_BATT_PCT
|
|
#undef CONFIG_HIBERNATE_BATT_SEC
|
|
|
|
/* For ECs with multiple wakeup pins, define enabled wakeup pins */
|
|
#undef CONFIG_HIBERNATE_WAKEUP_PINS
|
|
|
|
/* Use a hardware specific udelay(). */
|
|
#undef CONFIG_HW_SPECIFIC_UDELAY
|
|
|
|
/*****************************************************************************/
|
|
/* I2C configuration */
|
|
|
|
#undef CONFIG_I2C
|
|
#undef CONFIG_I2C_DEBUG
|
|
#undef CONFIG_I2C_DEBUG_PASSTHRU
|
|
#undef CONFIG_I2C_PASSTHROUGH
|
|
#undef CONFIG_I2C_PASSTHRU_RESTRICTED
|
|
#undef CONFIG_I2C_VIRTUAL_BATTERY
|
|
|
|
/* EC uses an I2C master interface */
|
|
#undef CONFIG_I2C_MASTER
|
|
|
|
/* EC uses an I2C slave interface */
|
|
#undef CONFIG_I2C_SLAVE
|
|
|
|
/* Defines I2C operation retry count when slave nack'd(EC_ERROR_BUSY) */
|
|
#define CONFIG_I2C_NACK_RETRY_COUNT 0
|
|
/*
|
|
* I2C SCL gating.
|
|
*
|
|
* If CONFIG_I2C_SCL_GATE_ADDR/PORT is defined, whenever the defined address
|
|
* is addressed, CONFIG_I2C_SCL_GATE_GPIO is set to high. When the I2C
|
|
* transaction is done, the pin is set back to low.
|
|
*/
|
|
#undef CONFIG_I2C_SCL_GATE_PORT
|
|
#undef CONFIG_I2C_SCL_GATE_ADDR
|
|
#undef CONFIG_I2C_SCL_GATE_GPIO
|
|
|
|
/*
|
|
* I2C multi-port controller.
|
|
*
|
|
* If CONFIG_I2C_MULTI_PORT_CONTROLLER is defined, a single on-chip I2C
|
|
* controller may have multiple I2C ports attached. Therefore, I2c operations
|
|
* must lock the controller (not just the port) to prevent hardware access
|
|
* conflicts.
|
|
*/
|
|
#undef CONFIG_I2C_MULTI_PORT_CONTROLLER
|
|
|
|
/*****************************************************************************/
|
|
/* Current/Power monitor */
|
|
|
|
/*
|
|
* Compile driver for INA219 or INA231. These two flags may not be both
|
|
* defined.
|
|
*/
|
|
#undef CONFIG_INA219
|
|
#undef CONFIG_INA231
|
|
|
|
/*****************************************************************************/
|
|
/* Inductive charging */
|
|
|
|
/* Enable inductive charging support */
|
|
#undef CONFIG_INDUCTIVE_CHARGING
|
|
|
|
/******************************************************************************/
|
|
|
|
/* Support NXP PCA9534 I/O expander. */
|
|
#undef CONFIG_IO_EXPANDER_PCA9534
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Number of IRQs supported on the EC chip */
|
|
#undef CONFIG_IRQ_COUNT
|
|
|
|
/*
|
|
* This is the block size of the ILM on the it839x chip.
|
|
* The ILM for static code cache, CPU fetch instruction from
|
|
* ILM(ILM -> CPU)instead of flash(flash -> IMMU -> CPU) if enabled.
|
|
*/
|
|
#undef CONFIG_IT83XX_ILM_BLOCK_SIZE
|
|
|
|
/* To define it, if I2C channel C and PECI used at the same time. */
|
|
#undef CONFIG_IT83XX_SMCLK2_ON_GPC7
|
|
|
|
/*****************************************************************************/
|
|
/* Keyboard config */
|
|
|
|
/*
|
|
* The Silego reset chip sits in between the EC and the physical keyboard on
|
|
* column 2. To save power in low-power modes, some Silego variants require
|
|
* the signal to be inverted so that the open-drain output from the EC isn't
|
|
* costing power due to the pull-up resistor in the Silego.
|
|
*/
|
|
#undef CONFIG_KEYBOARD_COL2_INVERTED
|
|
|
|
/*
|
|
* Config KSO to start from a different KSO pin. This is to allow some chips
|
|
* to use alternate functions on KSO pins.
|
|
*/
|
|
#define CONFIG_KEYBOARD_KSO_BASE 0
|
|
|
|
/*
|
|
* For certain board configurations, KSI2 will be stuck asserted for all
|
|
* scan columns if the power button is held. We must be aware of this case
|
|
* in order to correctly handle recovery mode key combinations.
|
|
*/
|
|
#undef CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2
|
|
|
|
/* Enable extra debugging output from keyboard modules */
|
|
#undef CONFIG_KEYBOARD_DEBUG
|
|
|
|
/* The board uses a negative edge-triggered GPIO for keyboard interrupts. */
|
|
#undef CONFIG_KEYBOARD_IRQ_GPIO
|
|
|
|
/* Compile code for 8042 keyboard protocol */
|
|
#undef CONFIG_KEYBOARD_PROTOCOL_8042
|
|
|
|
/* Compile code for MKBP keyboard protocol */
|
|
#undef CONFIG_KEYBOARD_PROTOCOL_MKBP
|
|
|
|
/* Support keyboard factory test scanning */
|
|
#undef CONFIG_KEYBOARD_FACTORY_TEST
|
|
|
|
/*
|
|
* Keyboard config (struct keyboard_scan_config) is in board.c. If this is
|
|
* not defined, default values from common/keyboard_scan.c will be used.
|
|
*/
|
|
#undef CONFIG_KEYBOARD_BOARD_CONFIG
|
|
|
|
/*
|
|
* Minimum CPU clocks between scans. This ensures that keyboard scanning
|
|
* doesn't starve the other EC tasks of CPU when running at a decreased system
|
|
* clock.
|
|
*/
|
|
#undef CONFIG_KEYBOARD_POST_SCAN_CLOCKS
|
|
|
|
/*
|
|
* Call board-supplied keyboard_suppress_noise() function when the debounced
|
|
* keyboard state changes. Some boards use this to send a signal to the audio
|
|
* codec to suppress typing noise picked up by the microphone.
|
|
*/
|
|
#undef CONFIG_KEYBOARD_SUPPRESS_NOISE
|
|
|
|
/*
|
|
* Enable keyboard testing functionality. This enables a message which receives
|
|
* a list of keyscan events from the AP and processes them. This will cause
|
|
* keypresses to appear on the AP through the same mechanism as a normal
|
|
* keyboard press.
|
|
*
|
|
* This can be used to spoof keyboard events, so is not normally defined,
|
|
* except during internal testing.
|
|
*/
|
|
#undef CONFIG_KEYBOARD_TEST
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Support common LED interface */
|
|
#undef CONFIG_LED_COMMON
|
|
|
|
/* Standard LED behavior according to spec given that we have a red-green
|
|
* bicolor led for charging and one power led
|
|
*/
|
|
#undef CONFIG_LED_POLICY_STD
|
|
|
|
/*
|
|
* LEDs for LED_POLICY STD may be inverted. In this case they are active low
|
|
* and the GPIO names will be GPIO_LED..._L.
|
|
*/
|
|
#undef CONFIG_LED_BAT_ACTIVE_LOW
|
|
#undef CONFIG_LED_POWER_ACTIVE_LOW
|
|
|
|
/* Support for LED driver chip(s) */
|
|
#undef CONFIG_LED_DRIVER_DS2413 /* Maxim DS2413, on one-wire interface */
|
|
#undef CONFIG_LED_DRIVER_LP5562 /* LP5562, on I2C interface */
|
|
|
|
/* Offset in flash where little firmware will live. */
|
|
#undef CONFIG_LFW_OFFSET
|
|
|
|
/*
|
|
* Compile lid switch support.
|
|
*
|
|
* This is enabled by default because all boards other than reference boards
|
|
* are for laptops with lid switchs. Reference boards #undef it.
|
|
*/
|
|
#define CONFIG_LID_SWITCH
|
|
|
|
/*
|
|
* GPIOs to use to detect that the lid is opened.
|
|
*
|
|
* This is a X-macro composed of a list of LID_OPEN(GPIO_xxx) elements defining
|
|
* all the GPIOs to check to find whether the lid is currently opened.
|
|
* If not defined, it is using GPIO_LID_OPEN.
|
|
*/
|
|
#undef CONFIG_LID_SWITCH_GPIO_LIST
|
|
|
|
/*
|
|
* Support for turning the lightbar power rails on briefly when the AP is off.
|
|
* Enabling this requires implementing the board-specific lb_power() function
|
|
* to do it (see lb_common.h).
|
|
*/
|
|
#undef CONFIG_LIGHTBAR_POWER_RAILS
|
|
|
|
/*
|
|
* For tap sequence, show the last segment in dim to give a better idea of
|
|
* battery percentage.
|
|
*/
|
|
#undef CONFIG_LIGHTBAR_TAP_DIM_LAST_SEGMENT
|
|
|
|
/* Program memory offset for little firmware loader. */
|
|
#undef CONFIG_LOADER_MEM_OFF
|
|
|
|
/* Size of little firmware loader. */
|
|
#undef CONFIG_LOADER_SIZE
|
|
|
|
/* Little firmware loader storage offset. */
|
|
#undef CONFIG_LOADER_STORAGE_OFF
|
|
|
|
/*
|
|
* Low power idle options. These are disabled by default and all boards that
|
|
* want to use low power idle must define it. When using the LFIOSC, the low
|
|
* frequency clock will be used to conserve even more power when possible.
|
|
*
|
|
* GPIOs which need to trigger interrupts in low power idle must specify the
|
|
* GPIO_INT_DSLEEP flag in gpio_list[].
|
|
*
|
|
* Note that for some processors (e.g. LM4), an active JTAG connection will
|
|
* prevent the EC from using low-power idle.
|
|
*/
|
|
#undef CONFIG_LOW_POWER_IDLE
|
|
#undef CONFIG_LOW_POWER_USE_LFIOSC
|
|
|
|
/*
|
|
* Enable deep sleep during S0 (ignores SLEEP_MASK_AP_RUN).
|
|
*/
|
|
#undef CONFIG_LOW_POWER_S0
|
|
|
|
/* Support LPC interface */
|
|
#undef CONFIG_LPC
|
|
|
|
/* Base address of low power RAM. */
|
|
#undef CONFIG_LPRAM_BASE
|
|
|
|
/* Size of low power RAM. */
|
|
#undef CONFIG_LPRAM_SIZE
|
|
|
|
/* Use Link-Time Optimizations to try to reduce the firmware code size */
|
|
#undef CONFIG_LTO
|
|
|
|
/* Need for a math library */
|
|
#undef CONFIG_MATH_UTIL
|
|
|
|
/* Include code to do online compass calibration */
|
|
#undef CONFIG_MAG_CALIBRATE
|
|
|
|
/* Presence of a Bosh Sensortec BMM150 magnetometer behind a BMI160. */
|
|
#undef CONFIG_MAG_BMI160_BMM150
|
|
|
|
/* Microchip EC SRAM start address */
|
|
#undef CONFIG_MEC_SRAM_BASE_START
|
|
|
|
/* Microchip EC SRAM end address */
|
|
#undef CONFIG_MEC_SRAM_BASE_END
|
|
|
|
/* Microchip EC SRAM size */
|
|
#undef CONFIG_MEC_SRAM_SIZE
|
|
|
|
/*
|
|
* Define Megachips DisplayPort to HDMI protocol converter/level shifter serial
|
|
* interface.
|
|
*/
|
|
#undef CONFIG_MCDP28X0
|
|
|
|
/* Define clock input to MFT module. */
|
|
#undef CONFIG_MFT_INPUT_LFCLK
|
|
|
|
/* Support MKBP event */
|
|
#undef CONFIG_MKBP_EVENT
|
|
|
|
/* MKBP events are sent using host event */
|
|
#undef CONFIG_MKBP_USE_HOST_EVENT
|
|
|
|
/*
|
|
* With this option, we can define the MKBP wakeup events in this mask (as a
|
|
* white list) in board level, those events allow to interrupt AP during S3.
|
|
*/
|
|
#undef CONFIG_MKBP_WAKEUP_MASK
|
|
|
|
/* Support memory protection unit (MPU) */
|
|
#undef CONFIG_MPU
|
|
|
|
/* Support one-wire interface */
|
|
#undef CONFIG_ONEWIRE
|
|
|
|
/* Support PECI interface to x86 processor */
|
|
#undef CONFIG_PECI
|
|
|
|
/*
|
|
* Maximum operating temperature in degrees Celcius used on some x86
|
|
* processors. CPU chip temperature is reported relative to this value and
|
|
* is never reported greater than this value. Processor asserts PROCHOT#
|
|
* and starts throttling frequency and voltage at this temp. Operation may
|
|
* become unreliable if temperature exceeds this limit.
|
|
*/
|
|
#undef CONFIG_PECI_TJMAX
|
|
|
|
/*****************************************************************************/
|
|
/* PMU config */
|
|
|
|
/*
|
|
* Enable hard-resetting the PMU from the EC. The implementation is rather
|
|
* hacky; it simply shorts out the 3.3V rail to force the PMIC to panic. We
|
|
* need this unfortunate hack because it's the only way to reset the I2C engine
|
|
* inside the PMU.
|
|
*/
|
|
#undef CONFIG_PMU_HARD_RESET
|
|
|
|
/* Support TPS65090 PMU */
|
|
#undef CONFIG_PMU_TPS65090
|
|
|
|
/* Suport TPS65090 PMU charging LED. */
|
|
#undef CONFIG_PMU_TPS65090_CHARGING_LED
|
|
|
|
/*
|
|
* Support PMU powerinfo host and console commands. Note that the
|
|
* implementation is currently specific to the Pit board, so don't blindly
|
|
* enable this for another board without fixing that first.
|
|
*/
|
|
#undef CONFIG_PMU_POWERINFO
|
|
|
|
/*
|
|
* Enable this config to make console UART self sufficient (no other
|
|
* initialization required before uart_init(), no interrupts, uart_tx_char()
|
|
* does not exit until character finished transmitting).
|
|
*
|
|
* This is useful during early hardware bringup, each platform needs to
|
|
* implement its own code to support this.
|
|
*/
|
|
#undef CONFIG_POLLING_UART
|
|
|
|
/* Compile common code to support power button debouncing */
|
|
#undef CONFIG_POWER_BUTTON
|
|
|
|
/* Force the active state of the power button : 0(default if unset) or 1 */
|
|
#undef CONFIG_POWER_BUTTON_ACTIVE_STATE
|
|
|
|
/* Allow the power button to send events while the lid is closed */
|
|
#undef CONFIG_POWER_BUTTON_IGNORE_LID
|
|
|
|
/* Support sending the power button signal to x86 chipsets */
|
|
#undef CONFIG_POWER_BUTTON_X86
|
|
|
|
/* Compile common code for AP power state machine */
|
|
#undef CONFIG_POWER_COMMON
|
|
|
|
/* Disable the power-on transition when the lid is opened */
|
|
#undef CONFIG_POWER_IGNORE_LID_OPEN
|
|
|
|
/* Support stopping in S5 on shutdown */
|
|
#undef CONFIG_POWER_SHUTDOWN_PAUSE_IN_S5
|
|
|
|
/*
|
|
* Detect power signal interrupt storms, defined as more than
|
|
* CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD occurences of a single
|
|
* power signal interrupt within one second.
|
|
*/
|
|
#undef CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD
|
|
|
|
/* Use part of the EC's data EEPROM to hold persistent storage for the AP. */
|
|
#undef CONFIG_PSTORE
|
|
|
|
/* Support S0ix */
|
|
#undef CONFIG_POWER_S0IX
|
|
|
|
/*
|
|
* Allow the host to self-report its sleep state, in case there is some delay
|
|
* between the host beginning to enter the sleep state and power signals
|
|
* actually reflecting the new state.
|
|
*/
|
|
#undef CONFIG_POWER_TRACK_HOST_SLEEP_STATE
|
|
/*****************************************************************************/
|
|
/* Support PWM control */
|
|
#undef CONFIG_PWM
|
|
|
|
/* Define clock input to PWM module. */
|
|
#undef CONFIG_PWM_INPUT_LFCLK
|
|
|
|
/*****************************************************************************/
|
|
/* Support PWM output to display backlight */
|
|
#undef CONFIG_PWM_DISPLIGHT
|
|
|
|
/* Support PWM output to keyboard backlight */
|
|
#undef CONFIG_PWM_KBLIGHT
|
|
|
|
/* Base address of RAM for the chip */
|
|
#undef CONFIG_RAM_BASE
|
|
|
|
/* Size of RAM available on the chip, in bytes */
|
|
#undef CONFIG_RAM_SIZE
|
|
|
|
/* Enable rbox peripheral */
|
|
#undef CONFIG_RBOX
|
|
|
|
/* Enable RDD peripheral */
|
|
#undef CONFIG_RDD
|
|
|
|
/* Support IR357x Link voltage regulator debugging / reprogramming */
|
|
#undef CONFIG_REGULATOR_IR357X
|
|
|
|
/* Support verifying 2048-bit RSA signature */
|
|
#undef CONFIG_RSA
|
|
|
|
/* Define the RSA key size. */
|
|
#undef CONFIG_RSA_KEY_SIZE
|
|
|
|
/*
|
|
* Verify the RW firmware using the RSA signature.
|
|
* (for accessories without software sync)
|
|
*/
|
|
#undef CONFIG_RWSIG
|
|
/*
|
|
* By default the pubkey and sig are put at the end of the first and second
|
|
* half of the total flash, and take up the minimum space possible. You can
|
|
* override those defaults with these.
|
|
*/
|
|
#undef CONFIG_RO_PUBKEY_ADDR
|
|
#undef CONFIG_RO_PUBKEY_SIZE
|
|
#undef CONFIG_RW_SIG_ADDR
|
|
#undef CONFIG_RW_SIG_SIZE
|
|
|
|
/****************************************************************************/
|
|
/* Shared objects library. */
|
|
|
|
/* Support shared objects library between RO and RW. */
|
|
#undef CONFIG_SHAREDLIB
|
|
|
|
/* Size of shared objects library. */
|
|
#undef CONFIG_SHAREDLIB_SIZE
|
|
|
|
/* Program memory offset of shared objects library. */
|
|
#undef CONFIG_SHAREDLIB_MEM_OFF
|
|
|
|
/* Storage offset of sharedobjects library. */
|
|
#undef CONFIG_SHAREDLIB_STORAGE_OFF
|
|
|
|
/*
|
|
* If defined, the hash module will save its last computed hash when jumping
|
|
* between EC images.
|
|
*/
|
|
#undef CONFIG_SAVE_VBOOT_HASH
|
|
|
|
/* Enable smart battery firmware update driver */
|
|
#undef CONFIG_SB_FIRMWARE_UPDATE
|
|
|
|
/* Allow the board to use a GPIO for the SCI# signal. */
|
|
#undef CONFIG_SCI_GPIO
|
|
|
|
/* Support computing SHA-1 hash */
|
|
#undef CONFIG_SHA1
|
|
|
|
/* Support computing of other hash sizes (without the VBOOT code) */
|
|
#undef CONFIG_SHA256
|
|
|
|
/* Emulate the CLZ (Count Leading Zeros) in software for CPU lacking support */
|
|
#undef CONFIG_SOFTWARE_CLZ
|
|
|
|
/* Support smbus interface */
|
|
#undef CONFIG_SMBUS
|
|
|
|
/* Support SPI interfaces */
|
|
#undef CONFIG_SPI
|
|
|
|
/* Support deprecated SPI protocol version 2. */
|
|
#undef CONFIG_SPI_PROTOCOL_V2
|
|
|
|
/*
|
|
* Support SPI Slave interfaces. The first board supporting this is cr50 and
|
|
* in its parlance SPI_SLAVE is called SPS. This convention might be
|
|
* reconsidered later, and the use of "SPI" in different config options needs
|
|
* to be cleand up. (crbug.com/512613).
|
|
*/
|
|
#undef CONFIG_SPS
|
|
|
|
/* Define the SPI port to use to access SPI accelerometer */
|
|
#undef CONFIG_SPI_ACCEL_PORT
|
|
|
|
/* Support SPI flash */
|
|
#undef CONFIG_SPI_FLASH
|
|
|
|
/* Define the SPI port to use to access the flash */
|
|
#undef CONFIG_SPI_FLASH_PORT
|
|
|
|
/* Support W25Q40 SPI flash */
|
|
#undef CONFIG_SPI_FLASH_W25Q40
|
|
|
|
/* Support W25Q64 SPI flash */
|
|
#undef CONFIG_SPI_FLASH_W25Q64
|
|
|
|
/* Support W25X40 SPI flash */
|
|
#undef CONFIG_SPI_FLASH_W25X40
|
|
|
|
/* Support GD25Q40 SPI flash */
|
|
#undef CONFIG_SPI_FLASH_GD25LQ40
|
|
|
|
/* Support GD25Q41B SPI flash */
|
|
#undef CONFIG_SPI_FLASH_GD25Q41B
|
|
|
|
/* SPI flash part supports SR2 register */
|
|
#undef CONFIG_SPI_FLASH_HAS_SR2
|
|
|
|
/* Support JEDEC SFDP based Serial NOR flash */
|
|
#undef CONFIG_SPI_NOR
|
|
|
|
/* Enable SPI_NOR debugging providing additional console output while
|
|
* initializing Serial NOR Flash devices including SFDP discovery. */
|
|
#undef CONFIG_SPI_NOR_DEBUG
|
|
|
|
/* Maximum Serial NOR flash command size, in Bytes */
|
|
#undef CONFIG_SPI_NOR_MAX_MESSAGE_SIZE
|
|
|
|
/* Maximum Serial NOR flash read size, in Bytes */
|
|
#undef CONFIG_SPI_NOR_MAX_READ_SIZE
|
|
|
|
/* Maximum Serial NOR flash write size, in Bytes. Note this must be a power of
|
|
* two. */
|
|
#undef CONFIG_SPI_NOR_MAX_WRITE_SIZE
|
|
|
|
/* SPI master feature */
|
|
#undef CONFIG_SPI_MASTER
|
|
|
|
/* SPI master configure gpios on init */
|
|
#undef CONFIG_SPI_MASTER_CONFIGURE_GPIOS
|
|
|
|
/* Support SPI masters without GPIO-specified Chip Selects, instead rely on the
|
|
* SPI master port's hardwired CS pin. */
|
|
#undef CONFIG_SPI_MASTER_NO_CS_GPIOS
|
|
|
|
/* Support testing SPI slave controller driver. */
|
|
#undef CONFIG_SPS_TEST
|
|
|
|
/* Default stack size to use for tasks, in bytes */
|
|
#undef CONFIG_STACK_SIZE
|
|
|
|
/* Use 32-bit timer for clock source on stm32. */
|
|
#undef CONFIG_STM_HWTIMER32
|
|
|
|
/* Compile charger detect for STM32 */
|
|
#undef CONFIG_STM32_CHARGER_DETECT
|
|
|
|
/* Fake hibernate mode */
|
|
#undef CONFIG_STM32L_FAKE_HIBERNATE
|
|
|
|
/*
|
|
* Compile common code to handle simple switch inputs such as the recovery
|
|
* button input from the servo debug interface.
|
|
*/
|
|
#undef CONFIG_SWITCH
|
|
|
|
/* Support dedicated recovery signal from servo board */
|
|
#undef CONFIG_SWITCH_DEDICATED_RECOVERY
|
|
|
|
/*
|
|
* System should remain unlocked even if write protect is enabled.
|
|
*
|
|
* NOTE: This should ONLY be defined during bringup, and should never be
|
|
* defined on a shipping / released platform.
|
|
*/
|
|
#undef CONFIG_SYSTEM_UNLOCKED
|
|
|
|
/*****************************************************************************/
|
|
/* Task config */
|
|
|
|
/*
|
|
* List of enabled tasks in ascending priority order. This is normally
|
|
* defined in each board's ec.tasklist file.
|
|
*
|
|
* For each task, use the macro TASK_ALWAYS(n, r, d, s) for base tasks and
|
|
* TASK_NOTEST(n, r, d, s) for tasks that can be excluded in test binaries,
|
|
* where :
|
|
* 'n' is the name of the task
|
|
* 'r' is the main routine of the task
|
|
* 'd' is an opaque parameter passed to the routine at startup
|
|
* 's' is the stack size in bytes; must be a multiple of 8
|
|
*/
|
|
#undef CONFIG_TASK_LIST
|
|
|
|
/*
|
|
* List of test tasks. Same format as CONFIG_TASK_LIST, but used to define
|
|
* additional tasks for a unit test. Normally defined in
|
|
* test/{testname}.tasklist.
|
|
*/
|
|
#undef CONFIG_TEST_TASK_LIST
|
|
|
|
/*
|
|
* List of tasks used by CTS
|
|
*
|
|
* cts.tasklist contains tasks run only for CTS. These tasks are added to the
|
|
* tasks registered in ec.tasklist with higher priority.
|
|
*
|
|
* If a CTS suite does not define its own cts.tasklist, the common list is used
|
|
* (i.e. cts/cts.tasklist).
|
|
*/
|
|
#undef CONFIG_CTS_TASK_LIST
|
|
|
|
/*
|
|
* Enable task profiling.
|
|
*
|
|
* Boards may #undef this to reduce image size and RAM usage.
|
|
*/
|
|
#define CONFIG_TASK_PROFILING
|
|
|
|
/*****************************************************************************/
|
|
/* Temperature sensor config */
|
|
|
|
/* Compile common code for temperature sensor support */
|
|
#undef CONFIG_TEMP_SENSOR
|
|
|
|
/* Support particular temperature sensor chips */
|
|
#undef CONFIG_TEMP_SENSOR_BD99992GW /* BD99992GW PMIC, on I2C bus */
|
|
#undef CONFIG_TEMP_SENSOR_EC_ADC /* Thermistors on EC's own ADC */
|
|
#undef CONFIG_TEMP_SENSOR_G781 /* G781 sensor, on I2C bus */
|
|
#undef CONFIG_TEMP_SENSOR_G782 /* G782 sensor, on I2C bus */
|
|
#undef CONFIG_TEMP_SENSOR_TMP006 /* TI TMP006 sensor, on I2C bus */
|
|
#undef CONFIG_TEMP_SENSOR_TMP432 /* TI TMP432 sensor, on I2C bus */
|
|
|
|
#undef CONFIG_THERMISTOR_NCP15WB /* NCP15WB thermistor */
|
|
|
|
/*
|
|
* If defined, active-high GPIO which indicates temperature sensor chips are
|
|
* powered. If not defined, temperature sensors are assumed to be always
|
|
* powered.
|
|
*/
|
|
#undef CONFIG_TEMP_SENSOR_POWER_GPIO
|
|
|
|
/* Compile common code for throttling the CPU based on the temp sensors */
|
|
#undef CONFIG_THROTTLE_AP
|
|
/*
|
|
* If defined, dptf is enabled to manage thermals.
|
|
*
|
|
* NOTE: This doesn't mean that thermal control is completely taken care by
|
|
* DPTF. We have some hybrid solutions where the EC still manages the fans.
|
|
*/
|
|
#undef CONFIG_DPTF
|
|
|
|
/*****************************************************************************/
|
|
/* TPM-like configuration */
|
|
|
|
/* Speak the TPM SPI Hardware Protocol on the SPI slave interface */
|
|
#undef CONFIG_TPM_SPS
|
|
/* Speak to the TPM 2.0 hardware protocol on the I2C slave interface */
|
|
#undef CONFIG_TPM_I2CS
|
|
|
|
/*****************************************************************************/
|
|
/* USART stream config */
|
|
#undef CONFIG_STREAM_USART
|
|
|
|
/*
|
|
* Each USART stream can be individually enabled and accessible using the
|
|
* stream interface provided in the usart_config struct.
|
|
*/
|
|
#undef CONFIG_STREAM_USART1
|
|
#undef CONFIG_STREAM_USART2
|
|
#undef CONFIG_STREAM_USART3
|
|
#undef CONFIG_STREAM_USART4
|
|
|
|
/*****************************************************************************/
|
|
/* USB stream config */
|
|
#undef CONFIG_STREAM_USB
|
|
|
|
/*****************************************************************************/
|
|
/* UART config */
|
|
|
|
/* Baud rate for UARTs */
|
|
#define CONFIG_UART_BAUD_RATE 115200
|
|
|
|
/* UART index (number) for EC console */
|
|
#undef CONFIG_UART_CONSOLE
|
|
|
|
/* UART index (number) for host UART, if present */
|
|
#undef CONFIG_UART_HOST
|
|
|
|
/* Use uart_input_filter() to filter UART input. See prototype in uart.h */
|
|
#undef CONFIG_UART_INPUT_FILTER
|
|
|
|
/*
|
|
* UART receive buffer size in bytes. Must be a power of 2 for macros in
|
|
* common/uart_buffering.c to work properly. Must be larger than
|
|
* CONFIG_CONSOLE_INPUT_LINE_SIZE to copy and paste scripts.
|
|
*/
|
|
#define CONFIG_UART_RX_BUF_SIZE 128
|
|
|
|
/* Use DMA for UART input */
|
|
#undef CONFIG_UART_RX_DMA
|
|
|
|
/*
|
|
* On some platforms, UART receive DMA can't trigger an interrupt when a single
|
|
* character is received. Those platforms poll for characters every HOOK_TICK.
|
|
* When a character is received, make this many additional checks between then
|
|
* and the next HOOK_TICK, to increase responsiveness of the console to input.
|
|
*/
|
|
#define CONFIG_UART_RX_DMA_RECHECKS 5
|
|
|
|
/*
|
|
* UART transmit buffer size in bytes. Must be a power of 2 for macros in
|
|
* common/uart_buffering.c to work properly.
|
|
*/
|
|
#define CONFIG_UART_TX_BUF_SIZE 512
|
|
|
|
/* Use DMA for UART output */
|
|
#undef CONFIG_UART_TX_DMA
|
|
|
|
/* The DMA channel for UART. If not defined, default to UART1. */
|
|
#undef CONFIG_UART_TX_DMA_CH
|
|
#undef CONFIG_UART_RX_DMA_CH
|
|
|
|
/* The DMA peripheral request signal for UART TX. STM32 only. */
|
|
#undef CONFIG_UART_TX_DMA_PH
|
|
|
|
/* The DMA channel mapping config for stm32f4. */
|
|
#undef CONFIG_UART_TX_REQ_CH
|
|
#undef CONFIG_UART_RX_REQ_CH
|
|
|
|
|
|
/*****************************************************************************/
|
|
/* USB PD config */
|
|
|
|
/* Include all USB Power Delivery modules */
|
|
#undef CONFIG_USB_POWER_DELIVERY
|
|
|
|
/* Support for USB PD alternate mode */
|
|
#undef CONFIG_USB_PD_ALT_MODE
|
|
|
|
/* Support for USB PD alternate mode of Downward Facing Port */
|
|
#undef CONFIG_USB_PD_ALT_MODE_DFP
|
|
|
|
/* Check if max voltage request is allowed before each request */
|
|
#undef CONFIG_USB_PD_CHECK_MAX_REQUEST_ALLOWED
|
|
|
|
/* Default state of PD communication enabled flag */
|
|
#define CONFIG_USB_PD_COMM_ENABLED
|
|
|
|
/*
|
|
* Do not enable PD communication in RO as a security measure.
|
|
* We don't want to allow communication to outside world until
|
|
* we jump to RW. This can by overridden with the removal of
|
|
* the write protect screw to allow for easier testing.
|
|
*/
|
|
#undef CONFIG_USB_PD_COMM_LOCKED
|
|
|
|
/* Respond to custom vendor-defined messages over PD */
|
|
#undef CONFIG_USB_PD_CUSTOM_VDM
|
|
|
|
/* Default USB data role when a USB PD debug accessory is seen */
|
|
#define CONFIG_USB_PD_DEBUG_DR PD_ROLE_DFP
|
|
|
|
/*
|
|
* Define if this board has a GPIO-controlled 5v discharge circuit that can be
|
|
* used to discharge VBUS when power swapping out of source role.
|
|
*/
|
|
#undef CONFIG_USB_PD_DISCHARGE_GPIO
|
|
|
|
/* Define if this board can act as a dual-role PD port (source and sink) */
|
|
#undef CONFIG_USB_PD_DUAL_ROLE
|
|
|
|
/*
|
|
* Define if VBUS source GPIOs (GPIO_USB_C*_5V_EN) are active-low (and named
|
|
* (..._L) rather than default active-high.
|
|
*/
|
|
#undef CONFIG_USB_PD_5V_EN_ACTIVE_LOW
|
|
|
|
/* Dynamic USB PD source capability */
|
|
#undef CONFIG_USB_PD_DYNAMIC_SRC_CAP
|
|
|
|
/* Support USB PD flash. */
|
|
#undef CONFIG_USB_PD_FLASH
|
|
|
|
/* Check whether PD is the sole power source before flash erase operation */
|
|
#undef CONFIG_USB_PD_FLASH_ERASE_CHECK
|
|
|
|
/* Major and Minor ChromeOS specific PD device Hardware IDs. */
|
|
#undef CONFIG_USB_PD_HW_DEV_ID_BOARD_MAJOR
|
|
#undef CONFIG_USB_PD_HW_DEV_ID_BOARD_MINOR
|
|
|
|
/* HW & SW version for alternate mode discover identity response (4bits each) */
|
|
#undef CONFIG_USB_PD_IDENTITY_HW_VERS
|
|
#undef CONFIG_USB_PD_IDENTITY_SW_VERS
|
|
|
|
/* USB PD MCU slave address for host commands */
|
|
#define CONFIG_USB_PD_I2C_SLAVE_ADDR 0x3c
|
|
|
|
/* Define if using internal comparator for PD receive */
|
|
#undef CONFIG_USB_PD_INTERNAL_COMP
|
|
|
|
/* Record main PD events in a circular buffer */
|
|
#undef CONFIG_USB_PD_LOGGING
|
|
|
|
/* The size in bytes of the FIFO used for PD events logging */
|
|
#undef CONFIG_USB_PD_LOG_SIZE
|
|
|
|
/* Save power by waking up on VBUS rather than polling CC */
|
|
#define CONFIG_USB_PD_LOW_POWER
|
|
|
|
/* Allow chip to go into low power idle even when a PD device is attached */
|
|
#undef CONFIG_USB_PD_LOW_POWER_IDLE_WHEN_CONNECTED
|
|
|
|
/* Number of USB PD ports */
|
|
#undef CONFIG_USB_PD_PORT_COUNT
|
|
|
|
/* Workaround TCPC that takes longer time to update CC status */
|
|
#undef CONFIG_USB_PD_QUIRK_SLOW_CC_STATUS
|
|
|
|
/* Simple DFP, such as power adapter, will not send discovery VDM on connect */
|
|
#undef CONFIG_USB_PD_SIMPLE_DFP
|
|
|
|
/* Use comparator module for PD RX interrupt */
|
|
#define CONFIG_USB_PD_RX_COMP_IRQ
|
|
|
|
/* Use TCPC module (type-C port controller) */
|
|
#undef CONFIG_USB_PD_TCPC
|
|
|
|
/*
|
|
* Track VBUS level in TCPC module. This will only be needed if we're acting
|
|
* as an external TCPC.
|
|
*/
|
|
#undef CONFIG_USB_PD_TCPC_TRACK_VBUS
|
|
|
|
/*
|
|
* Choose one of the following TCPMs (type-C port manager) to manage TCPC. The
|
|
* TCPM stub is used to make direct function calls to TCPC when TCPC is on
|
|
* the same MCU. The TCPCI TCPM uses the standard TCPCI i2c interface to TCPC.
|
|
*/
|
|
#undef CONFIG_USB_PD_TCPM_STUB
|
|
#undef CONFIG_USB_PD_TCPM_TCPCI
|
|
#undef CONFIG_USB_PD_TCPM_FUSB302
|
|
#undef CONFIG_USB_PD_TCPM_ITE83XX
|
|
#undef CONFIG_USB_PD_TCPM_ANX74XX
|
|
#undef CONFIG_USB_PD_TCPM_ANX7688
|
|
#undef CONFIG_USB_PD_TCPM_PS8751
|
|
|
|
/*
|
|
* Use this option if the TCPC port controller supports the optional register
|
|
* 18h CONFIG_STANDARD_OUTPUT to steer the high-speed muxes.
|
|
*/
|
|
#undef CONFIG_USB_PD_TCPM_MUX
|
|
|
|
/*
|
|
* The TCPM must know whether VBUS is present in order to make proper state
|
|
* transitions. In addition, charge_manager must know about VBUS presence in
|
|
* order to make charging decisions. VBUS state can be determined by various
|
|
* methods:
|
|
* - Some TCPCs can detect and report the presence of VBUS.
|
|
* - In some configurations, charger ICs can report the presence of VBUS.
|
|
* - On some boards, dedicated VBUS interrupt pins are available.
|
|
*
|
|
* Exactly one of these should be defined for all boards that run the PD
|
|
* state machine.
|
|
*/
|
|
#undef CONFIG_USB_PD_VBUS_DETECT_TCPC
|
|
#undef CONFIG_USB_PD_VBUS_DETECT_CHARGER
|
|
#undef CONFIG_USB_PD_VBUS_DETECT_GPIO
|
|
#undef CONFIG_USB_PD_VBUS_DETECT_NONE
|
|
|
|
|
|
/* Define the type-c port controller I2C base address. */
|
|
#define CONFIG_TCPC_I2C_BASE_ADDR 0x9c
|
|
|
|
/* Use this option to enable Try.SRC mode for Dual Role devices */
|
|
#undef CONFIG_USB_PD_TRY_SRC
|
|
|
|
/* Set the default minimum battery percentage for Try.Src to be enabled */
|
|
#define CONFIG_USB_PD_TRY_SRC_MIN_BATT_SOC 1
|
|
|
|
/* Alternative configuration keeping only the TX part of PHY */
|
|
#undef CONFIG_USB_PD_TX_PHY_ONLY
|
|
|
|
/* Use DAC as reference for comparator at 850mV. */
|
|
#undef CONFIG_PD_USE_DAC_AS_REF
|
|
|
|
/* USB Product ID. */
|
|
#undef CONFIG_USB_PID
|
|
|
|
/* Support for USB type-c superspeed mux */
|
|
#undef CONFIG_USBC_SS_MUX
|
|
|
|
/*
|
|
* Only configure USB type-c superspeed mux when DFP (for chipsets that
|
|
* don't support being a UFP)
|
|
*/
|
|
#undef CONFIG_USBC_SS_MUX_DFP_ONLY
|
|
|
|
/* Sniffer header version
|
|
* Version 1: [timestamp:2B, sequence number:2B]
|
|
* Version 2: [timestamp:2B, sequence number:2B,
|
|
* Vbus value: 2B, vbus timestamp offset: 2B]
|
|
*/
|
|
#undef CONFIG_USBC_SNIFFER_HEADER_V1
|
|
#undef CONFIG_USBC_SNIFFER_HEADER_V2
|
|
|
|
/* Support v1.1 type-C connection state machine */
|
|
#undef CONFIG_USBC_BACKWARDS_COMPATIBLE_DFP
|
|
|
|
/* Support for USB type-c vconn. Not needed for captive cables. */
|
|
#undef CONFIG_USBC_VCONN
|
|
|
|
/* Support VCONN swap */
|
|
#undef CONFIG_USBC_VCONN_SWAP
|
|
|
|
/* USB Binary device Object Store support */
|
|
#undef CONFIG_USB_BOS
|
|
|
|
/* USB Device version of product */
|
|
#undef CONFIG_USB_BCD_DEV
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Compile chip support for the USB device controller */
|
|
#undef CONFIG_USB
|
|
|
|
/* Support USB blob handler. */
|
|
#undef CONFIG_USB_BLOB
|
|
|
|
/* Common USB / BC1.2 charger detection routines */
|
|
#undef CONFIG_USB_CHARGER
|
|
|
|
/* Enable USB serial console module. */
|
|
#undef CONFIG_USB_CONSOLE
|
|
|
|
/* Support USB HID interface. */
|
|
#undef CONFIG_USB_HID
|
|
|
|
/* USB device buffers and descriptors */
|
|
#undef CONFIG_USB_RAM_ACCESS_SIZE
|
|
#undef CONFIG_USB_RAM_ACCESS_TYPE
|
|
#undef CONFIG_USB_RAM_BASE
|
|
#undef CONFIG_USB_RAM_SIZE
|
|
|
|
/* Disable automatic connection of USB peripheral */
|
|
#undef CONFIG_USB_INHIBIT_CONNECT
|
|
|
|
/* Disable automatic initialization of USB peripheral */
|
|
#undef CONFIG_USB_INHIBIT_INIT
|
|
|
|
/* Support control of multiple PHY */
|
|
#undef CONFIG_USB_SELECT_PHY
|
|
|
|
/* Support simple control of power to the device's USB ports */
|
|
#undef CONFIG_USB_PORT_POWER_DUMB
|
|
|
|
/*
|
|
* Support supplying USB power in S3, if the host leaves the port enabled when
|
|
* entering S3.
|
|
*/
|
|
#undef CONFIG_USB_PORT_POWER_IN_S3
|
|
|
|
/*
|
|
* Support smart power control to the device's USB ports, using
|
|
* dedicated power control chips. This potentially enables automatic
|
|
* negotiation of supplying more power to peripherals.
|
|
*/
|
|
#undef CONFIG_USB_PORT_POWER_SMART
|
|
|
|
/*
|
|
* Override the default charging mode for USB smart power control.
|
|
* Value is selected from usb_charge_mode in include/usb_charge.h
|
|
*/
|
|
#undef CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE
|
|
|
|
/*
|
|
* Smart USB power control can use a full set of control signals to the USB
|
|
* port power chip, or a reduced set. If this is defined, use the reduced set.
|
|
*/
|
|
#undef CONFIG_USB_PORT_POWER_SMART_SIMPLE
|
|
|
|
/* Number of smart USB power ports. */
|
|
#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 2
|
|
|
|
/*
|
|
* Smart USB power control current limit pins may be inverted. In this case
|
|
* they are active low and the GPIO names will be GPIO_USBn_ILIM_SEL_L.
|
|
*/
|
|
#undef CONFIG_USB_PORT_POWER_SMART_INVERTED
|
|
|
|
/* Support programmable USB device iSerial field. */
|
|
#undef CONFIG_USB_SERIALNO
|
|
|
|
/* Support reporting of configuration bMaxPower in mA */
|
|
#define CONFIG_USB_MAXPOWER_MA 500
|
|
|
|
/* Support reporting as self powered in USB configuration. */
|
|
#undef CONFIG_USB_SELF_POWERED
|
|
|
|
/* Default pull-up value on the USB-C ports when they are used as source. */
|
|
#define CONFIG_USB_PD_PULLUP TYPEC_RP_1A5
|
|
/*
|
|
* Override the pull-up value when only zero or one port is actively sourcing
|
|
* current and we can advertise more current than what is defined by
|
|
* `CONFIG_USB_PD_PULLUP`.
|
|
* Should be defined with one of the tcpc_rp_value.
|
|
*/
|
|
#undef CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT
|
|
|
|
|
|
/******************************************************************************/
|
|
/* stm32f4 dwc usb configs. */
|
|
|
|
/* Set USB speed to FS rather than HS */
|
|
#undef CONFIG_USB_DWC_FS
|
|
|
|
/******************************************************************************/
|
|
/* USB port switch */
|
|
|
|
/* Support the Pericom PI3USB9281 I2C USB switch */
|
|
#undef CONFIG_USB_SWITCH_PI3USB9281
|
|
|
|
/* Number of Pericom PI3USB9281 chips present in system */
|
|
#undef CONFIG_USB_SWITCH_PI3USB9281_CHIP_COUNT
|
|
|
|
/* Support the Pericom PI3USB30532 USB3.0/DP1.2 Matrix Switch */
|
|
#undef CONFIG_USB_MUX_PI3USB30532
|
|
|
|
/* Support the Parade PS8740 Type-C Redriving Switch */
|
|
#undef CONFIG_USB_MUX_PS8740
|
|
|
|
/* 'Virtual' USB mux under host (not EC) control */
|
|
#undef CONFIG_USB_MUX_VIRTUAL
|
|
|
|
/*****************************************************************************/
|
|
/* USB GPIO config */
|
|
#undef CONFIG_USB_GPIO
|
|
|
|
/*****************************************************************************/
|
|
/* USB SPI config */
|
|
#undef CONFIG_USB_SPI
|
|
|
|
/*****************************************************************************/
|
|
/* USB I2C config */
|
|
#undef CONFIG_USB_I2C
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Support computing hash of code for verified boot */
|
|
#undef CONFIG_VBOOT_HASH
|
|
|
|
/* Support for secure temporary storage for verified boot */
|
|
#undef CONFIG_VSTORE
|
|
|
|
/* Number of supported slots for secure temporary storage */
|
|
#undef CONFIG_VSTORE_SLOT_COUNT
|
|
|
|
/*****************************************************************************/
|
|
/* Watchdog config */
|
|
|
|
/*
|
|
* Compile watchdog timer support. The watchdog timer will reboot the system
|
|
* if the hook task (which is the lowest-priority task on the system) gets
|
|
* starved for CPU time and isn't able to fire its HOOK_TICK event.
|
|
*/
|
|
#define CONFIG_WATCHDOG
|
|
|
|
/*
|
|
* Try to detect a watchdog that is about to fire, and print a trace. This is
|
|
* required on chips such as STM32 where the watchdog timer simply reboots the
|
|
* system without any early warning.
|
|
*/
|
|
#undef CONFIG_WATCHDOG_HELP
|
|
|
|
/* Watchdog period in ms; see also AUX_TIMER_PERIOD_MS */
|
|
#define CONFIG_WATCHDOG_PERIOD_MS 1600
|
|
|
|
/*
|
|
* Fire auxiliary timer 500ms before watchdog timer expires. This leaves
|
|
* some time for debug trace to be printed.
|
|
*/
|
|
#define CONFIG_AUX_TIMER_PERIOD_MS (CONFIG_WATCHDOG_PERIOD_MS - 500)
|
|
|
|
/*****************************************************************************/
|
|
|
|
/*
|
|
* Support controlling power to WiFi, WWAN (3G/LTE), and/or bluetooth modules.
|
|
*/
|
|
#undef CONFIG_WIRELESS
|
|
|
|
/*
|
|
* Support for WiFi devices that must remain powered in suspend. Set to the
|
|
* combination of EC_WIRELESS_SWITCH flags (from ec_commands.h) which should
|
|
* be set in suspend.
|
|
*/
|
|
#undef CONFIG_WIRELESS_SUSPEND
|
|
|
|
/* WiFi power control signal is active-low. */
|
|
#undef CONFIG_WLAN_POWER_ACTIVE_LOW
|
|
|
|
/*
|
|
* Write protect signal is active-high. If this is defined, there must be a
|
|
* GPIO named GPIO_WP; if not defined, there must be a GPIO names GPIO_WP_L.
|
|
*/
|
|
#undef CONFIG_WP_ACTIVE_HIGH
|
|
|
|
/*
|
|
* The write protect signal is always asserted,
|
|
* independantly of the GPIO existence or current value.
|
|
*/
|
|
#undef CONFIG_WP_ALWAYS
|
|
|
|
/*
|
|
* If needed to allocate some free space in the base of the RO or RW section
|
|
* of the image, define these to be equal the required size of the free space.
|
|
*/
|
|
#undef CONFIG_RO_HEAD_ROOM
|
|
#undef CONFIG_RW_HEAD_ROOM
|
|
|
|
/* Firmware upgrade options. */
|
|
/* Firmware updates using other than HC channel(s). */
|
|
#undef CONFIG_NON_HC_FW_UPDATE
|
|
#undef CONFIG_USB_FW_UPDATE
|
|
/* A different config for the same update. TODO(vbendeb): dedup these */
|
|
#undef CONFIG_USB_UPDATE
|
|
|
|
/*****************************************************************************/
|
|
/*
|
|
* Include board and core configs, since those hold the CONFIG_ constants for a
|
|
* given configuration. This guarantees they get included everywhere, and
|
|
* fixes a fairly common bug where we gate out code with #ifndef
|
|
* CONFIG_SOMETHING and but forget to include both of these.
|
|
*
|
|
* Board is included after chip, so that chip defaults can be overridden on a
|
|
* per-board basis as needed.
|
|
*/
|
|
#ifdef __CROS_EC_CONFIG_CHIP_H
|
|
#error Include config.h instead of config_chip.h!
|
|
#endif
|
|
#ifdef __BOARD_H
|
|
#error Include config.h instead of board.h!
|
|
#endif
|
|
|
|
#include "config_chip.h"
|
|
#include "board.h"
|
|
|
|
/******************************************************************************/
|
|
/*
|
|
* Disable the built-in console history if using the experimental console.
|
|
*
|
|
* The experimental console keeps its own session-persistent history which
|
|
* survives EC reboot. It also requires CRC8 for command integrity.
|
|
*/
|
|
#ifdef CONFIG_EXPERIMENTAL_CONSOLE
|
|
#undef CONFIG_CONSOLE_HISTORY
|
|
#define CONFIG_CRC8
|
|
#endif /* defined(CONFIG_EXPERIMENTAL_CONSOLE) */
|
|
|
|
/******************************************************************************/
|
|
/*
|
|
* Throttle AP must have temperature sensor enabled to get the readings for
|
|
* thermal throttling.
|
|
*/
|
|
#if defined(CONFIG_THROTTLE_AP) && !defined(CONFIG_TEMP_SENSOR)
|
|
#define CONFIG_TEMP_SENSOR
|
|
#endif
|
|
|
|
/******************************************************************************/
|
|
/*
|
|
* DPTF must have temperature sensor enabled to get the readings for
|
|
* generating DPTF thresholds events.
|
|
*/
|
|
#if defined(CONFIG_DPTF) && !defined(CONFIG_TEMP_SENSOR)
|
|
#define CONFIG_TEMP_SENSOR
|
|
#endif
|
|
|
|
|
|
/******************************************************************************/
|
|
/* The Matrix Keyboard Protocol depends on MKBP events. */
|
|
#ifdef CONFIG_KEYBOARD_PROTOCOL_MKBP
|
|
#define CONFIG_MKBP_EVENT
|
|
#endif
|
|
|
|
/*****************************************************************************/
|
|
/*
|
|
* Handle task-dependent configs.
|
|
*
|
|
* This prevent sub-modules from being compiled when the task and parent module
|
|
* are not present.
|
|
*/
|
|
|
|
#ifndef HAS_TASK_CHIPSET
|
|
#undef CONFIG_CHIPSET_APOLLOLAKE
|
|
#undef CONFIG_CHIPSET_BAYTRAIL
|
|
#undef CONFIG_CHIPSET_BRASWELL
|
|
#undef CONFIG_CHIPSET_GAIA
|
|
#undef CONFIG_CHIPSET_HASWELL
|
|
#undef CONFIG_CHIPSET_MEDIATEK
|
|
#undef CONFIG_CHIPSET_RK3399
|
|
#undef CONFIG_CHIPSET_ROCKCHIP
|
|
#undef CONFIG_CHIPSET_SKYLAKE
|
|
#undef CONFIG_CHIPSET_TEGRA
|
|
#undef CONFIG_POWER_COMMON
|
|
#undef CONFIG_POWER_TRACK_HOST_SLEEP_STATE
|
|
#endif
|
|
|
|
#ifndef HAS_TASK_KEYPROTO
|
|
#undef CONFIG_KEYBOARD_PROTOCOL_8042
|
|
/*
|
|
* Note that we don't undef CONFIG_KEYBOARD_PROTOCOL_MKBP, because it doesn't
|
|
* have its own task.
|
|
*/
|
|
#endif
|
|
|
|
#ifndef HAS_TASK_KEYSCAN
|
|
#undef CONFIG_KEYBOARD_PROTOCOL_8042
|
|
#undef CONFIG_KEYBOARD_PROTOCOL_MKBP
|
|
#endif
|
|
|
|
#ifndef HAS_TASK_PDCMD
|
|
#undef CONFIG_HOSTCMD_PD
|
|
#endif
|
|
|
|
/*****************************************************************************/
|
|
/*
|
|
* Apply test config overrides last, since tests need to override some of the
|
|
* config flags in non-standard ways to mock only parts of the system.
|
|
*/
|
|
#include "test_config.h"
|
|
|
|
/*
|
|
* Sanity checks to make sure some of the configs above make sense.
|
|
*/
|
|
|
|
#if (CONFIG_AUX_TIMER_PERIOD_MS) < ((HOOK_TICK_INTERVAL_MS) * 2)
|
|
#error "CONFIG_AUX_TIMER_PERIOD_MS must be at least 2x HOOK_TICK_INTERVAL_MS"
|
|
#endif
|
|
|
|
#endif /* __CROS_EC_CONFIG_H */
|