Add self-altered DTS file for DR-6018v4 by robimarko found on OpenWRT forum
Add DR6018v4 image target to makefile
Include DR6018v4 network specifics to board daemon script
Ensure DR6018v4 calibration data for firmware hotplug
Allow upgrade path scripting for DR6018v4
Signed-off-by: okoklets <mike@vale.net.au>
Aruba boards now ship with multiple DTS and image-configurations per
image. Newer apboot revs expect a configuration for their hardware to be
present.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.
Fixes: e497c975d3 ("ramips: mt76x8: add support for Yuncore M300")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.
Fixes: 64dae1052b ("ramips: mt76x8: add support for Yuncore CPE200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
This alias was present in 6.1. Add back to restore a fully working console after
sbi0 (earlycon) gets disabled during the boot process.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
configure 2.5G PHY LEDs to:
2500/1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
which is similar to other 1G PHY LEDs, which are:
1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
Fixes: 6cc14bf66a ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the logic required to install OpenWrt on a
Cisco/Viptela vEdge 1000 while nicely integrating with the already
present bootloader and making it possible to roll back to stock OS.
The vEdge 1000 has a built-in SSD with a ext2 partition from which
the stock u-boot boots the Linux kernel from.
In order for Linux not to be confused about which partition the root
file system is on, there are some tricks needed to ensure the partition
is identifiable at boot time. For this we use blkid as part of the
scripts, and sfdisk as part of the manual installation process
documented on the wiki. Thus, those packages have been added as a
platform dependency. Finally, the u-boot environment is updated which
requires the use of uboot-envtools.
Tested on a Cisco vEdge 1000.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Link: https://github.com/openwrt/openwrt/pull/16140
Signed-off-by: Robert Marko <robimarko@gmail.com>
Yuncore CPE200 is an outdoor unit with IEEE 802.11ac radio.
Hardware:
- SoC: MediaTek MT7628DAN (MIPS 580MHz)
- Flash: 8 MiB Spansion S25FL064K
- RAM: 64 MiB (built-into SoC)
- WLAN: 5 GHz (MT7613AE)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- Buttons: 1 Reset button, 2 buttons for display UI (unsupported)
- LEDs: 4x Green (Power, LAN, WAN, WiFi)
- Display: 4 digit 7-segment display driven by an additional
microcontroller (unsupported)
- Serial console: unpopulated header, 57600 8n1 (RX only)
- Power: 12 VDC, 1 A
Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.0.100/ and upload sysupgrade.bin file.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MediaTek SDK uses eth2 as additional LAN port and eth1 as WAN.
Do the same also in OpenWrt to keep settings aligned with the SDK.
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
