mirror of
https://github.com/Telecominfraproject/wlan-ap.git
synced 2025-10-29 09:32:34 +00:00
ipq5018: add support for indio um-335ax
**Specifications:**
SOC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
Flash: SPI NOR 8MB (Winbond W25Q64DW) + NAND 128MB (Winbond W25N01GWZEIG)
Memory: 512MB DDR3L
Standard: 802.11ax/ac/b/g/n
2.4G Frequency: 2.4GHz - 2.484GHz
2.4G Wi-Fi standard: 802.11b/g/n/ax
5G Chipset: QCN9074
5G Frequency: 5.150GHz~5.850GHz
5G Wi-Fi Standard: 802.11 a/n/ac/ax
Buttons: 1 * Reset button, press 10 seconds to revert to default setting
2.4G Antenna: 2*2.4GHz/5.8GHz dual band antenna: 4dBi
5G Antenna: 2*5.8G antenna: 4dBi
Data Rate: 2.4GHz: 574Mbps, 5GHz:4800Mbps
Power: PoE 802.3at，DC2.0 12V/2A
Max Power Consumption: < 22W
LED Light: WAN, LAN, tricolor LED(sys-red, 2.4G-green, 5.8G-blue)
**BACKUP YOUR STOCK FIRMWARE:**
- Put openwrt-*-initramfs-kernel.bin to your TFTP server and rename it to initramfs.bin
- Enable serial console and enter to u-boot cli and exec these commands:
```
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
```
- Once boot completed and you get the openwrt shell execute below commands:
```
device=um335ax
mkdir -p /tmp/fw_backup; cd /tmp/fw_backup
rootfs=$(cat /proc/mtd | grep \"rootfs\" | cut -d: -f1)
rootfs_1=$(cat /proc/mtd | grep \"rootfs_1\" | cut -d: -f1)
dd if=/dev/${rootfs} of=rootfs_${rootfs} bs=1M
dd if=/dev/${rootfs_1} of=rootfs_1_${rootfs_1} bs=1M
cp /sys/firmware/fdt fdt.dtb
md5sum * > md5sum
tar -cvzf /tmp/${device}.tar.gz .
sum=$(md5sum /tmp/${device}.tar.gz | cut -d' ' -f1)
mv /tmp/${device}.tar.gz /tmp/${device}_${sum}.tar.gz
echo "stock fw backup saved to: /tmp/${device}_${sum}.tar.gz"
```
- Upload/save your backup to a safe place.
**STOCK FIRMWARE RECOVERY:**
- Boot initramfs image
- Upload your backed-up stock fw tarball to the device
using scp or download it from the device using wget.
- Enter device ssh cli or tty and exec:
```
cd /tmp && wget <your_web_server_ip>/${stock_fw_backup}.tar.gz`
tar -xpzf ${stock_fw_backup}.tar.gz
rootfs=$(cat /proc/mtd | grep \"rootfs\" | cut -d: -f1)
rootfs_1=$(cat /proc/mtd | grep \"rootfs_1\" | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f /tmp/rootfs_${rootfs}
ubiformat /dev/${rootfs_1} -y -f /tmp/rootfs_1_${rootfs_1}
reboot
```
**INSTALLATION:**
1. initramfs method
- Put openwrt-*-initramfs-kernel.bin to your TFTP server and rename it to initramfs.bin
- Enable serial console and enter to u-boot cli and exec these commands:
```
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
```
- Once boot completed and you get the openwrt shell execute below commands:
```
cd /tmp && wget <your_web_server_ip>/factory.ubi`
export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1)
export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f factory.ubi
ubiformat /dev/${rootfs_1} -y -f factory.ubi
reboot
```
2. u-boot nand-factory.bin image method
- Put openwrt-*-squashfs-nand-factory.bin to your TFTP server and enter u-boot cli and exec these commands:
```
tftpboot <your_tftp_server_ip>:factory.bin
#After downloading is finished:
imxtract 0x44000000 ubi
flash rootfs
flash rootfs_1
reset
```
Signed-off-by: Shubham Vishwakarma <shubhamvis98@fossfrog.in>
This commit is contained in:
Shubham Vishwakarma
committed by
John Crispin
John Crispin
parent
92d67c15dd
commit
6ed93db422
@@ -48,6 +48,7 @@ ALLWIFIBOARDS:= \
|
||||
indio-um-510axp-v1 \
|
||||
indio-um-510axm-v1 \
|
||||
indio-um-325ax-v2 \
|
||||
indio-um-335ax \
|
||||
indio-um-525axp \
|
||||
muxi-ap3220l \
|
||||
plasmacloud-pax1800 \
|
||||
@@ -444,6 +445,7 @@ $(eval $(call generate-ath11k-wifi-package,indio-um-310ax-v1,Indio UM-310AX V1))
|
||||
$(eval $(call generate-ath11k-wifi-package,indio-um-510axp-v1,Indio UM-510AXP V1))
|
||||
$(eval $(call generate-ath11k-wifi-package,indio-um-510axm-v1,Indio UM-510AXM V1))
|
||||
$(eval $(call generate-ath11k-wifi-package,indio-um-325ax-v2,Indio UM-325AX V2))
|
||||
$(eval $(call generate-ath11k-wifi-package,indio-um-335ax,Indio UM-335AX))
|
||||
$(eval $(call generate-ath11k-wifi-package,indio-um-525axp,Indio UM-525AXP))
|
||||
$(eval $(call generate-ath11k-wifi-package,sonicfi-rap630c-311g,Sonicfi RAP630C 311G))
|
||||
$(eval $(call generate-ath11k-wifi-package,sonicfi-rap630w-311g,Sonicfi RAP630W 311G))
|
||||
|
||||
BIN
feeds/ipq807x_v5.4/ath11k-wifi/board-indio-um-335ax.bin.IPQ5018
Normal file
BIN
feeds/ipq807x_v5.4/ath11k-wifi/board-indio-um-335ax.bin.IPQ5018
Normal file
Binary file not shown.
BIN
feeds/ipq807x_v5.4/ath11k-wifi/board-indio-um-335ax.bin.QCN9074
Normal file
BIN
feeds/ipq807x_v5.4/ath11k-wifi/board-indio-um-335ax.bin.QCN9074
Normal file
Binary file not shown.
@@ -17,11 +17,11 @@ edgecore,eap104)
|
||||
ucidef_set_led_default "power" "POWER" "green:power" "on"
|
||||
;;
|
||||
indio,um-325ax-v2|\
|
||||
indio,um-335ax|\
|
||||
indio,um-525axp)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wifi2" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wifi5" "phy1tpt"
|
||||
ucidef_set_led_netdev "wan" "wan" "yellow:uplink" "eth0"
|
||||
ucidef_set_led_default "power" "POWER" "green:power" "on"
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "led_2g" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "led_5g" "phy1tpt"
|
||||
ucidef_set_led_default "power" "POWER" "led_sys" "on"
|
||||
;;
|
||||
cig,wf186h|\
|
||||
cig,wf186w)
|
||||
|
||||
@@ -49,6 +49,7 @@ qcom_setup_interfaces()
|
||||
"6u@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
|
||||
;;
|
||||
indio,um-325ax-v2|\
|
||||
indio,um-335ax|\
|
||||
indio,um-525axp)
|
||||
ucidef_set_interface_wan "eth1"
|
||||
ucidef_set_interface_lan "eth0"
|
||||
|
||||
@@ -143,6 +143,7 @@ ath11k/IPQ5018/hw1.0/caldata.bin)
|
||||
hfcl,ion4x_w|\
|
||||
hfcl,ion4xi_w|\
|
||||
indio,um-325ax-v2|\
|
||||
indio,um-335ax|\
|
||||
indio,um-525axp|\
|
||||
optimcloud,d60|\
|
||||
optimcloud,d60-5g|\
|
||||
@@ -205,6 +206,7 @@ ath11k/qcn6122/hw1.0/caldata_2.bin)
|
||||
;;
|
||||
ath11k/QCN9074/hw1.0/caldata_1.bin)
|
||||
case "$board" in
|
||||
indio,um-335ax|\
|
||||
optimcloud,d60|\
|
||||
optimcloud,d60-5g|\
|
||||
optimcloud,d50|\
|
||||
|
||||
@@ -82,6 +82,7 @@ platform_check_image() {
|
||||
hfcl,ion4x_w|\
|
||||
hfcl,ion4xi_w|\
|
||||
indio,um-325ax-v2|\
|
||||
indio,um-335ax|\
|
||||
indio,um-525axp|\
|
||||
optimcloud,d60|\
|
||||
optimcloud,d60-5g|\
|
||||
@@ -110,6 +111,7 @@ platform_do_upgrade() {
|
||||
board=$(board_name)
|
||||
case $board in
|
||||
indio,um-325ax-v2|\
|
||||
indio,um-335ax|\
|
||||
indio,um-525axp|\
|
||||
edgecore,oap101|\
|
||||
edgecore,oap101-6e|\
|
||||
|
||||
@@ -0,0 +1,731 @@
|
||||
/dts-v1/;
|
||||
/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
|
||||
* Copyright (c) 2025, Shubham Vishwakarma <shubhamvis98@fossfrog.in>.
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
|
||||
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
|
||||
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
|
||||
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
|
||||
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
|
||||
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
|
||||
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
|
||||
*/
|
||||
|
||||
#include "ipq5018.dtsi"
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
#address-cells = <0x2>;
|
||||
#size-cells = <0x2>;
|
||||
model = "Indio UM-335AX";
|
||||
compatible = "indio,um-335ax", "qcom,ipq5018-ap-mp03.1", "qcom,ipq5018-mp03.1", "qcom,ipq5018";
|
||||
interrupt-parent = <&intc>;
|
||||
|
||||
aliases {
|
||||
sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
|
||||
serial0 = &blsp1_uart1;
|
||||
serial1 = &blsp1_uart2;
|
||||
ethernet0 = "/soc/dp1";
|
||||
ethernet1 = "/soc/dp2";
|
||||
led-boot = &led_red;
|
||||
led-failsafe = &led_red;
|
||||
led-running = &led_red;
|
||||
led-upgrade = &led_red;
|
||||
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
|
||||
bootargs-append = " swiotlb=1 coherent_pool=2M";
|
||||
stdout-path = "serial0";
|
||||
};
|
||||
|
||||
gpio-watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
|
||||
hw_algo = "toggle";
|
||||
hw_margin_ms = <5000>;
|
||||
always-running;
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
q6_mem_regions: q6_mem_regions@4B000000 {
|
||||
no-map;
|
||||
reg = <0x0 0x4B000000 0x0 0x1800000>;
|
||||
};
|
||||
|
||||
q6_ipq5018_data: q6_ipq5018_data@4C400000 {
|
||||
no-map;
|
||||
reg = <0x0 0x4C400000 0x0 0xE00000>;
|
||||
};
|
||||
|
||||
m3_dump: m3_dump@4C800000 {
|
||||
no-map;
|
||||
reg = <0x0 0x4C800000 0x0 0x100000>;
|
||||
};
|
||||
|
||||
q6_etr_region: q6_etr_dump@4C900000 {
|
||||
no-map;
|
||||
reg = <0x0 0x4C900000 0x0 0x100000>;
|
||||
};
|
||||
|
||||
q6_caldb_region: q6_caldb_region@4CA00000 {
|
||||
no-map;
|
||||
reg = <0x0 0x4CA00000 0x0 0x200000>;
|
||||
};
|
||||
|
||||
qcn9000_pcie0: qcn9000_pcie0@4cc00000 {
|
||||
no-map;
|
||||
reg = <0x0 0x4CC00000 0x0 0x2600000>;
|
||||
};
|
||||
|
||||
#if defined(__CNSS2__)
|
||||
mhi_region1: dma_pool1@4F200000 {
|
||||
compatible = "shared-dma-pool";
|
||||
no-map;
|
||||
reg = <0x0 0x4F200000 0x0 0x900000>;
|
||||
};
|
||||
#endif
|
||||
};
|
||||
|
||||
soc {
|
||||
serial@78af000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
blsp1_uart2: serial@78b0000 {
|
||||
pinctrl-0 = <&blsp1_uart_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
qpic_bam: dma@7984000{
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
nand: qpic-nand@79b0000 {
|
||||
pinctrl-0 = <&qspi_nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
spi_0: spi@78b5000 { /* BLSP1 QUP0 */
|
||||
pinctrl-0 = <&blsp0_spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-select = <0>;
|
||||
status = "ok";
|
||||
|
||||
m25p80@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
compatible = "n25q128a11";
|
||||
linux,modalias = "m25p80", "n25q128a11";
|
||||
spi-max-frequency = <50000000>;
|
||||
use-default-sizes;
|
||||
};
|
||||
};
|
||||
|
||||
mdio0: mdio@88000 {
|
||||
status = "ok";
|
||||
|
||||
ethernet-phy@0 {
|
||||
reg = <7>;
|
||||
};
|
||||
};
|
||||
|
||||
mdio1: mdio@90000 {
|
||||
status = "ok";
|
||||
pinctrl-0 = <&mdio1_pins>;
|
||||
pinctrl-names = "default";
|
||||
phy-reset-gpio = <&tlmm 39 0>;
|
||||
|
||||
ethernet-phy@0 {
|
||||
reg = <28>;
|
||||
};
|
||||
};
|
||||
|
||||
ess-instance {
|
||||
num_devices = <0x1>;
|
||||
ess-switch@0x39c00000 {
|
||||
switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
|
||||
cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
|
||||
qcom,port_phyinfo {
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
phy_address = <7>;
|
||||
mdiobus = <&mdio0>;
|
||||
};
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
phy_address = <0x1c>;
|
||||
mdiobus = <&mdio1>;
|
||||
port_mac_sel = "QGMAC_PORT";
|
||||
};
|
||||
};
|
||||
led_source@0 {
|
||||
source = <0>;
|
||||
mode = "normal";
|
||||
speed = "all";
|
||||
blink_en = "enable";
|
||||
active = "high";
|
||||
};
|
||||
};
|
||||
ess-switch1@1 {
|
||||
compatible = "qcom,ess-switch-qca83xx";
|
||||
device_id = <1>;
|
||||
switch_access_mode = "mdio";
|
||||
mdio-bus = <&mdio1>;
|
||||
reset_gpio = <0x28>;
|
||||
switch_cpu_bmp = <0x40>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x1e>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x0>; /* wan port bitmap */
|
||||
qca,ar8327-initvals = <
|
||||
0x00004 0x7600000 /* PAD0_MODE */
|
||||
0x00008 0x1000000 /* PAD5_MODE */
|
||||
0x0000c 0x80 /* PAD6_MODE */
|
||||
0x00010 0x2613a0 /* PORT6 FORCE MODE*/
|
||||
0x000e4 0xaa545 /* MAC_POWER_SEL */
|
||||
0x000e0 0xc74164de /* SGMII_CTRL */
|
||||
0x0007c 0x4e /* PORT0_STATUS */
|
||||
0x00094 0x4e /* PORT6_STATUS */
|
||||
>;
|
||||
qcom,port_phyinfo {
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
phy_address = <28>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
dp1 {
|
||||
device_type = "network";
|
||||
compatible = "qcom,nss-dp";
|
||||
clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
|
||||
clock-names = "nss-snoc-gmac-axi-clk";
|
||||
qcom,id = <1>;
|
||||
reg = <0x39C00000 0x10000>;
|
||||
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
|
||||
qcom,mactype = <2>;
|
||||
qcom,link-poll = <1>;
|
||||
qcom,phy-mdio-addr = <7>;
|
||||
mdio-bus = <&mdio0>;
|
||||
local-mac-address = [000000000000];
|
||||
phy-mode = "sgmii";
|
||||
};
|
||||
|
||||
dp2 {
|
||||
device_type = "network";
|
||||
compatible = "qcom,nss-dp";
|
||||
clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
|
||||
clock-names = "nss-snoc-gmac-axi-clk";
|
||||
qcom,id = <2>;
|
||||
reg = <0x39D00000 0x10000>;
|
||||
interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
|
||||
qcom,mactype = <2>;
|
||||
qcom,link-poll = <1>;
|
||||
qcom,phy-mdio-addr = <28>;
|
||||
mdio-bus = <&mdio1>;
|
||||
local-mac-address = [000000000000];
|
||||
phy-mode = "sgmii";
|
||||
};
|
||||
|
||||
qcom,test@0 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
nss-macsec1 {
|
||||
compatible = "qcom,nss-macsec";
|
||||
phy_addr = <0x1c>;
|
||||
mdiobus = <&mdio1>;
|
||||
};
|
||||
|
||||
lpass: lpass@0xA000000{
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pcm: pcm@0xA3C0000{
|
||||
pinctrl-0 = <&audio_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pcm_lb: pcm_lb@0 {
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
thermal-zones {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
blsp0_uart_pins: uart_pins {
|
||||
blsp0_uart_rx_tx {
|
||||
pins = "gpio20", "gpio21";
|
||||
function = "blsp0_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
blsp1_uart_pins: blsp1_uart_pins {
|
||||
blsp1_uart_rx_tx {
|
||||
pins = "gpio22", "gpio24", "gpio23", "gpio25";
|
||||
function = "blsp1_uart2";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
blsp0_spi_pins: blsp0_spi_pins {
|
||||
mux {
|
||||
pins = "gpio10", "gpio11", "gpio12", "gpio13";
|
||||
function = "blsp0_spi";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
qspi_nand_pins: qspi_nand_pins {
|
||||
qspi_clock {
|
||||
pins = "gpio9";
|
||||
function = "qspi_clk";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
qspi_cs {
|
||||
pins = "gpio8";
|
||||
function = "qspi_cs";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
qspi_data_0 {
|
||||
pins = "gpio7";
|
||||
function = "qspi0";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
qspi_data_1 {
|
||||
pins = "gpio6";
|
||||
function = "qspi1";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
qspi_data_2 {
|
||||
pins = "gpio5";
|
||||
function = "qspi2";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
qspi_data_3 {
|
||||
pins = "gpio4";
|
||||
function = "qspi3";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
mdio1_pins: mdio_pinmux {
|
||||
mux_0 {
|
||||
pins = "gpio36";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_1 {
|
||||
pins = "gpio37";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
phy_led_pins: phy_led_pins {
|
||||
gephy_led_pin {
|
||||
pins = "gpio46";
|
||||
function = "led0";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
i2c_pins: i2c_pins {
|
||||
i2c_scl {
|
||||
pins = "gpio25";
|
||||
function = "blsp2_i2c1";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
i2c_sda {
|
||||
pins = "gpio26";
|
||||
function = "blsp2_i2c1";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
button_pins: button_pins {
|
||||
reset_button {
|
||||
pins = "gpio38";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
audio_pins: audio_pinmux {
|
||||
};
|
||||
|
||||
leds_pins: leds_pins {
|
||||
led_blue: led_5g {
|
||||
label = "led_5g";
|
||||
pins = "gpio34";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
led_green: led_2g {
|
||||
label = "led_2g";
|
||||
pins = "gpio33";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
led_red: led_sys {
|
||||
label = "led_sys";
|
||||
pins = "gpio26";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
led_onekey {
|
||||
pins = "gpio28";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&soc {
|
||||
gpio_keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
button@1 {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
linux,input-type = <1>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&leds_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led@33 {
|
||||
label = "led_5g";
|
||||
gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "led_5g";
|
||||
default-state = "off";
|
||||
};
|
||||
led@34 {
|
||||
label = "led_2g";
|
||||
gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "led_2g";
|
||||
default-state = "off";
|
||||
};
|
||||
led@26 {
|
||||
label = "led_sys";
|
||||
gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "led_sys";
|
||||
default-state = "on";
|
||||
};
|
||||
led@28 {
|
||||
label = "led_onekey";
|
||||
gpios = <&tlmm 28 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "led_onekey";
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&q6v5_wcss {
|
||||
compatible = "qcom,ipq5018-q6-mpd";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
firmware = "IPQ5018/q6_fw.mdt";
|
||||
reg = <0x0cd00000 0x4040>,
|
||||
<0x1938000 0x8>,
|
||||
<0x193d204 0x4>;
|
||||
reg-names = "qdsp6",
|
||||
"tcsr-msip",
|
||||
"tcsr-q6";
|
||||
resets = <&gcc GCC_WCSSAON_RESET>,
|
||||
<&gcc GCC_WCSS_Q6_BCR>;
|
||||
|
||||
reset-names = "wcss_aon_reset",
|
||||
"wcss_q6_reset";
|
||||
|
||||
clocks = <&gcc GCC_Q6_AXIS_CLK>,
|
||||
<&gcc GCC_WCSS_ECAHB_CLK>,
|
||||
<&gcc GCC_Q6_AXIM_CLK>,
|
||||
<&gcc GCC_Q6_AXIM2_CLK>,
|
||||
<&gcc GCC_Q6_AHB_CLK>,
|
||||
<&gcc GCC_Q6_AHB_S_CLK>,
|
||||
<&gcc GCC_WCSS_AXI_S_CLK>;
|
||||
clock-names = "gcc_q6_axis_clk",
|
||||
"gcc_wcss_ecahb_clk",
|
||||
"gcc_q6_axim_clk",
|
||||
"gcc_q6_axim2_clk",
|
||||
"gcc_q6_ahb_clk",
|
||||
"gcc_q6_ahb_s_clk",
|
||||
"gcc_wcss_axi_s_clk";
|
||||
|
||||
memory-region = <&q6_mem_regions>, <&q6_etr_region>,
|
||||
<&q6_caldb_region>;
|
||||
|
||||
qcom,rproc = <&q6v5_wcss>;
|
||||
qcom,bootargs_smem = <507>;
|
||||
boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>,
|
||||
<0x2 0x4 0x2 0x12 0x0 0x0>;
|
||||
status = "ok";
|
||||
q6_wcss_pd1: remoteproc_pd1@4ab000 {
|
||||
compatible = "qcom,ipq5018-wcss-ahb-mpd";
|
||||
reg = <0x4ab000 0x20>;
|
||||
reg-names = "rmb";
|
||||
firmware = "IPQ5018/q6_fw.mdt";
|
||||
m3_firmware = "IPQ5018/m3_fw.mdt";
|
||||
interrupts-extended = <&wcss_smp2p_in 8 0>,
|
||||
<&wcss_smp2p_in 9 0>,
|
||||
<&wcss_smp2p_in 12 0>,
|
||||
<&wcss_smp2p_in 11 0>;
|
||||
interrupt-names = "fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
resets = <&gcc GCC_WCSSAON_RESET>,
|
||||
<&gcc GCC_WCSS_BCR>,
|
||||
<&gcc GCC_CE_BCR>;
|
||||
reset-names = "wcss_aon_reset",
|
||||
"wcss_reset",
|
||||
"ce_reset";
|
||||
|
||||
clocks = <&gcc GCC_WCSS_AHB_S_CLK>,
|
||||
<&gcc GCC_WCSS_ACMT_CLK>,
|
||||
<&gcc GCC_WCSS_AXI_M_CLK>;
|
||||
clock-names = "gcc_wcss_ahb_s_clk",
|
||||
"gcc_wcss_acmt_clk",
|
||||
"gcc_wcss_axi_m_clk";
|
||||
|
||||
qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
|
||||
|
||||
qcom,smem-states = <&wcss_smp2p_out 8>,
|
||||
<&wcss_smp2p_out 9>,
|
||||
<&wcss_smp2p_out 10>;
|
||||
qcom,smem-state-names = "shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
memory-region = <&q6_ipq5018_data>, <&m3_dump>,
|
||||
<&q6_etr_region>, <&q6_caldb_region>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c_0 {
|
||||
pinctrl-0 = <&i2c_pins>;
|
||||
pinctrl-names = "default";
|
||||
// status = "disabled";
|
||||
};
|
||||
|
||||
&usb3 {
|
||||
status = "ok";
|
||||
device-power-gpio = <&tlmm 24 1>;
|
||||
};
|
||||
|
||||
&dwc_0 {
|
||||
/delete-property/ #phy-cells;
|
||||
/delete-property/ phys;
|
||||
/delete-property/ phy-names;
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&ssuniphy_0 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&hs_m31phy_0 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&eud {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&pcie_x1 {
|
||||
perst-gpio = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pcie_x2 {
|
||||
status = "ok";
|
||||
perst-gpio = <&tlmm 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&wcss {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&pcie_x2phy {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&pcie_x1_rp {
|
||||
status = "disabled";
|
||||
|
||||
mhi_0: qcom,mhi@0 {
|
||||
reg = <0 0 0 0 0 >;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie_x2_rp {
|
||||
status = "ok";
|
||||
|
||||
mhi_1: qcom,mhi@1 {
|
||||
reg = <0 0 0 0 0 >;
|
||||
qrtr_instance_id = <0x20>;
|
||||
qti,disable-rddm-prealloc;
|
||||
qti,rddm-seg-len = <0x1000>;
|
||||
#address-cells = <0x2>;
|
||||
#size-cells = <0x2>;
|
||||
#if defined(__CNSS2__)
|
||||
memory-region = <0>,<&mhi_region1>;
|
||||
#else
|
||||
base-addr = <0x4CB00000>;
|
||||
m3-dump-addr = <0x4DF00000>;
|
||||
etr-addr = <0x4E000000>;
|
||||
qcom,caldb-addr = <0x4E100000>;
|
||||
pageable-addr = <0x4E900000>;
|
||||
qcom,tgt-mem-mode = <0x1>;
|
||||
#endif
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
/* IPQ5018 */
|
||||
qcom,multipd_arch;
|
||||
qcom,rproc = <&q6_wcss_pd1>;
|
||||
qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
|
||||
qcom,tgt-mem-mode = <1>;
|
||||
qcom,board_id = <0x24>;
|
||||
#ifdef __CNSS2__
|
||||
qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
|
||||
qcom,caldb-addr = <0x4D400000 0x4D400000 0 0 0>;
|
||||
qcom,caldb-size = <0x200000>;
|
||||
mem-region = <&q6_ipq5018_data>;
|
||||
#else
|
||||
memory-region = <&q6_ipq5018_data>;
|
||||
#endif
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&wifi3 {
|
||||
/* QCN9000 5G */
|
||||
board_id = <0xa0>;
|
||||
hremote_node = <&qcn9000_pcie0>;
|
||||
#ifdef __IPQ_MEM_PROFILE_256_MB__
|
||||
/* QCN9000 tgt-mem-mode=2 layout - 17MB
|
||||
* +=========+==============+=========+
|
||||
* | Region | Start Offset | Size |
|
||||
* +---------+--------------+---------+
|
||||
* | HREMOTE | 0x4C900000 | 11MB |
|
||||
* +---------+--------------+---------+
|
||||
* | M3 Dump | 0x4D400000 | 1MB |
|
||||
* +---------+--------------+---------+
|
||||
* | ETR | 0x4D500000 | 1MB |
|
||||
* +---------+--------------+---------+
|
||||
* | Pageable| 0x4D600000 | 4MB |
|
||||
* +==================================+
|
||||
*/
|
||||
base-addr = <0x4C900000>;
|
||||
m3-dump-addr = <0x4D400000>;
|
||||
etr-addr = <0x4D500000>;
|
||||
caldb-addr = <0>;
|
||||
pageable-addr = <0x4D600000>;
|
||||
caldb-size = <0>;
|
||||
hremote-size = <0xB00000>;
|
||||
tgt-mem-mode = <0x2>;
|
||||
pageable-size = <0x400000>;
|
||||
#elif __IPQ_MEM_PROFILE_512_MB__
|
||||
/* QCN9000 tgt-mem-mode=1 layout - 26MB
|
||||
* +=========+==============+=========+
|
||||
* | Region | Start Offset | Size |
|
||||
* +---------+--------------+---------+
|
||||
* | HREMOTE | 0x4CB00000 | 12MB |
|
||||
* +---------+--------------+---------+
|
||||
* | M3 Dump | 0x4D700000 | 1MB |
|
||||
* +---------+--------------+---------+
|
||||
* | ETR | 0x4D800000 | 1MB |
|
||||
* +---------+--------------+---------+
|
||||
* | Caldb | 0x4D900000 | 8MB |
|
||||
* +---------+--------------+---------+
|
||||
* | Pageable| 0x4E100000 | 4MB |
|
||||
* +==================================+
|
||||
*/
|
||||
base-addr = <0x4CB00000>;
|
||||
m3-dump-addr = <0x4D700000>;
|
||||
etr-addr = <0x4D800000>;
|
||||
caldb-addr = <0x4D900000>;
|
||||
pageable-addr = <0x4E100000>;
|
||||
caldb-size = <0x800000>;
|
||||
hremote-size = <0xC00000>;
|
||||
tgt-mem-mode = <0x1>;
|
||||
pageable-size = <0x400000>;
|
||||
#else
|
||||
/* QCN9000 tgt-mem-mode=0 layout - 53MB
|
||||
* +=========+==============+=========+
|
||||
* | Region | Start Offset | Size |
|
||||
* +---------+--------------+---------+
|
||||
* | HREMOTE | 0x4CB00000 | 35MB |
|
||||
* +---------+--------------+---------+
|
||||
* | M3 Dump | 0x4EE00000 | 1MB |
|
||||
* +---------+--------------+---------+
|
||||
* | ETR | 0x4EF00000 | 1MB |
|
||||
* +---------+--------------+---------+
|
||||
* | Caldb | 0x4F000000 | 8MB |
|
||||
* +---------+--------------+---------+
|
||||
* | Pageable| 0x4F800000 | 8MB |
|
||||
* +==================================+
|
||||
*/
|
||||
base-addr = <0x4CB00000>;
|
||||
m3-dump-addr = <0x4EE00000>;
|
||||
etr-addr = <0x4EF00000>;
|
||||
caldb-addr = <0x4F000000>;
|
||||
pageable-addr = <0x4F800000>;
|
||||
hremote-size = <0x2300000>;
|
||||
caldb-size = <0x800000>;
|
||||
tgt-mem-mode = <0x0>;
|
||||
pageable-size = <0x800000>;
|
||||
#endif
|
||||
status = "ok";
|
||||
};
|
||||
@@ -102,6 +102,15 @@ define Device/indio_um-325ax-v2
|
||||
endef
|
||||
TARGET_DEVICES += indio_um-325ax-v2
|
||||
|
||||
define Device/indio_um-335ax
|
||||
DEVICE_TITLE := Indio UM-335ax
|
||||
DEVICE_DTS := qcom-ipq5018-indio-um-335ax
|
||||
SUPPORTED_DEVICES := indio,um-335ax
|
||||
DEVICE_PACKAGES := ath11k-wifi-indio-um-335ax ath11k-firmware-qcn9000 ath11k-firmware-ipq50xx-spruce
|
||||
DEVICE_DTS_CONFIG := config@mp03.1
|
||||
endef
|
||||
TARGET_DEVICES += indio_um-335ax
|
||||
|
||||
define Device/indio_um-525axp
|
||||
DEVICE_TITLE := Indio UM-525axp
|
||||
DEVICE_DTS := qcom-ipq5018-indio-um-525axp
|
||||
|
||||
18
profiles/indio_um-335ax.yml
Normal file
18
profiles/indio_um-335ax.yml
Normal file
@@ -0,0 +1,18 @@
|
||||
---
|
||||
profile: indio_um-335ax
|
||||
target: ipq50xx
|
||||
subtarget: generic
|
||||
description: Build image for the Indio um-335ax
|
||||
image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-indio_um-335ax-squashfs-sysupgrade.tar
|
||||
feeds:
|
||||
- name: ipq807x
|
||||
path: ../../feeds/ipq807x_v5.4
|
||||
include:
|
||||
- ucentral-ap
|
||||
packages:
|
||||
- ipq50xx
|
||||
diffconfig: |
|
||||
CONFIG_KERNEL_IPQ_MEM_PROFILE=512
|
||||
CONFIG_BUSYBOX_CUSTOM=y
|
||||
CONFIG_BUSYBOX_CONFIG_STTY=y
|
||||
|
||||
Reference in New Issue
Block a user