mirror of
https://github.com/Telecominfraproject/wlan-ap.git
synced 2025-10-31 02:17:58 +00:00
WIFI-14524 WF189/W/H Add 189H support
Signed-off-by: Ken <xshi@actiontec.com>
This commit is contained in:
Ken
@@ -53,6 +53,11 @@ $(call Package/ath12k-wifi-default)
|
||||
TITLE:=board-2.bin for RAP750W_311a
|
||||
endef
|
||||
|
||||
define Package/ath12k-wifi-cig-wf189h
|
||||
$(call Package/ath12k-wifi-default)
|
||||
TITLE:=board-2.bin for WF189H
|
||||
endef
|
||||
|
||||
define Package/ath12k-wifi-cig-wf189w
|
||||
$(call Package/ath12k-wifi-default)
|
||||
TITLE:=board-2.bin for WF189W
|
||||
@@ -96,8 +101,18 @@ define Package/ath12k-wifi-cig-wf189w/install
|
||||
$(INSTALL_DATA) ./ipq5332_qcn6432.regdb $(1)/lib/firmware/ath12k/QCN6432/hw1.0/regdb.bin
|
||||
endef
|
||||
|
||||
|
||||
define Package/ath12k-wifi-cig-wf189h/install
|
||||
$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
|
||||
$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN6432/hw1.0/
|
||||
$(INSTALL_DATA) ./board-2.bin.189h.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
|
||||
$(INSTALL_DATA) ./board-2.bin.189h.QCN6432 $(1)/lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin
|
||||
$(INSTALL_DATA) ./ipq5332_qcn6432.regdb $(1)/lib/firmware/ath12k/QCN6432/hw1.0/regdb.bin
|
||||
endef
|
||||
|
||||
$(eval $(call BuildPackage,ath12k-wifi-cig-wf189))
|
||||
$(eval $(call BuildPackage,ath12k-wifi-edgecore-eap105))
|
||||
$(eval $(call BuildPackage,ath12k-wifi-sonicfi-rap7110c-341x))
|
||||
$(eval $(call BuildPackage,ath12k-wifi-sonicfi-rap750w-311a))
|
||||
$(eval $(call BuildPackage,ath12k-wifi-cig-wf189w))
|
||||
$(eval $(call BuildPackage,ath12k-wifi-cig-wf189h))
|
||||
|
||||
BIN
feeds/qca-wifi-7/ath12k-wifi/board-2.bin.189h.IPQ5332
Normal file
BIN
feeds/qca-wifi-7/ath12k-wifi/board-2.bin.189h.IPQ5332
Normal file
Binary file not shown.
BIN
feeds/qca-wifi-7/ath12k-wifi/board-2.bin.189h.QCN6432
Normal file
BIN
feeds/qca-wifi-7/ath12k-wifi/board-2.bin.189h.QCN6432
Normal file
Binary file not shown.
@@ -14,9 +14,6 @@ sercomm,ap72tip)
|
||||
sonicfi,rap7110c-341x)
|
||||
ucidef_set_led_default "power" "POWER" "pwm:blue" "on"
|
||||
;;
|
||||
cig,wf189w)
|
||||
ucidef_set_led_default "power" "POWER" "pwm:blue" "on"
|
||||
;;
|
||||
esac
|
||||
|
||||
board_config_flush
|
||||
|
||||
@@ -22,7 +22,12 @@ ipq53xx_setup_interfaces()
|
||||
ucidef_set_interfaces_lan_wan "" "eth0"
|
||||
;;
|
||||
cig,wf189w)
|
||||
ucidef_add_switch "switch1" "5u@eth0" "3:lan" "2:lan" "1:lan" "0u@eth1" "4:wan"
|
||||
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
||||
ucidef_add_switch "switch1" "0u@eth1" "3:lan" "2:lan" "1:lan"
|
||||
;;
|
||||
cig,wf189h)
|
||||
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
||||
ucidef_add_switch "switch1" "0u@eth1" "3:lan" "2:lan"
|
||||
;;
|
||||
esac
|
||||
}
|
||||
@@ -32,6 +37,7 @@ qcom_setup_macs()
|
||||
local board="$1"
|
||||
case $board in
|
||||
cig,wf189w|\
|
||||
cig,wf189h|\
|
||||
cig,wf189)
|
||||
mtd=$(find_mtd_chardev "0:APPSBLENV")
|
||||
[ -z "$mtd" ] && return;
|
||||
|
||||
@@ -28,6 +28,7 @@ case "$FIRMWARE" in
|
||||
ath12k/IPQ5332/hw1.0/caldata.bin)
|
||||
case "$board" in
|
||||
cig,wf189w|\
|
||||
cig,wf189h|\
|
||||
cig,wf189|\
|
||||
edgecore,eap105|\
|
||||
sercomm,ap72tip)
|
||||
@@ -62,6 +63,7 @@ ath12k/QCN6432/hw1.0/caldata_1.bin)
|
||||
;;
|
||||
ath12k/QCN6432/hw1.0/cal-ahb-soc@0:wifi1@c0000000.bin)
|
||||
case "$board" in
|
||||
cig,wf189h|\
|
||||
cig,wf189w)
|
||||
caldata_extract "0:ART" 0x26800 0x20000
|
||||
;;
|
||||
@@ -69,6 +71,7 @@ ath12k/QCN6432/hw1.0/cal-ahb-soc@0:wifi1@c0000000.bin)
|
||||
;;
|
||||
ath12k/QCN6432/hw1.0/cal-ahb-soc@0:wifi2@c0000000.bin)
|
||||
case "$board" in
|
||||
cig,wf189h|\
|
||||
cig,wf189w)
|
||||
caldata_extract "0:ART" 0x58800 0x20000
|
||||
;;
|
||||
|
||||
@@ -87,6 +87,7 @@ platform_do_upgrade() {
|
||||
board=$(board_name)
|
||||
case $board in
|
||||
cig,wf189w|\
|
||||
cig,wf189h|\
|
||||
cig,wf189)
|
||||
if [ -f /proc/boot_info/bootconfig0/rootfs/upgradepartition ]; then
|
||||
CI_UBIPART="$(cat /proc/boot_info/bootconfig0/rootfs/upgradepartition)"
|
||||
|
||||
@@ -23,6 +23,10 @@
|
||||
serial1 = &blsp1_uart1;
|
||||
ethernet0 = "/soc/dp1";
|
||||
ethernet1 = "/soc/dp2";
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
};
|
||||
|
||||
chosen {
|
||||
@@ -178,12 +182,25 @@
|
||||
pinctrl-0 = <&gpio_leds_default>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led-0 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tx";
|
||||
default-state = "off";
|
||||
led_power_blue: led@26 {
|
||||
label = "status:blue";
|
||||
gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
|
||||
max-brightness = <160>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
|
||||
led_power_green:led@30 {
|
||||
label = "status:green";
|
||||
gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
|
||||
max-brightness = <160>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
|
||||
led_power_red:led@45 {
|
||||
label = "status:red";
|
||||
gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>;
|
||||
max-brightness = <160>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
};
|
||||
|
||||
@@ -481,6 +498,24 @@
|
||||
bias-pull-up;
|
||||
output-low;
|
||||
};
|
||||
|
||||
led_pins: led_pins {
|
||||
mux_1 {
|
||||
pins = "gpio26";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
};
|
||||
mux_2 {
|
||||
pins = "gpio30";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
};
|
||||
mux_3 {
|
||||
pins = "gpio45";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&license_manager {
|
||||
|
||||
777
feeds/qca-wifi-7/ipq53xx/dts/ipq5332-cig-wf189h.dts
Normal file
777
feeds/qca-wifi-7/ipq53xx/dts/ipq5332-cig-wf189h.dts
Normal file
@@ -0,0 +1,777 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
|
||||
/*
|
||||
* IPQ5332 RDP446 board device tree source
|
||||
*
|
||||
* Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
|
||||
* Copyright (c) 2022-2024 Qualcomm Innovation Center, Inc. All rights reserved.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq5332.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include "ipq5332-default-memory.dtsi"
|
||||
|
||||
/ {
|
||||
model = "CIG WF189H";
|
||||
compatible = "cig,wf189h", "qcom,ipq5332-ap-mi04.1", "qcom,ipq5332-rdp446", "qcom,ipq5332";
|
||||
|
||||
/* 1G Layout for IPQ5332 + QCN6432 + QCN6432
|
||||
* +==========+==============+========================+
|
||||
* | | | |
|
||||
* | Region | Start Offset | Size |
|
||||
* | | | |
|
||||
* +---------+--------------+-------------------------+
|
||||
* | Q6 | | |
|
||||
* | code/ | 0x4A900000 | 25MB |
|
||||
* | data | | |
|
||||
* +---------+--------------+-------------------------+
|
||||
* | IPQ5332 | | |
|
||||
* | data | 0x4C200000 | 21MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* | IPQ5332 | | |
|
||||
* | M3 Dump | 0x4D700000 | 1MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* | IPQ5332 | | |
|
||||
* | QDSS | 0x4D800000 | 1MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* | IPQ5332 | | |
|
||||
* | CALDB | 0x4D900000 | 5MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* |QCN6432_1| | |
|
||||
* | data | 0x4DE00000 | 21MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* |QCN6432_1| | |
|
||||
* | M3 Dump | 0x4F300000 | 1MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* |QCN6432_1| | |
|
||||
* | QDSS | 0x4E400000 | 1MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* |QCN6432_1| | |
|
||||
* | CALDB | 0x4F500000 | 5MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* |QCN6432_2| | |
|
||||
* | data | 0x4FA00000 | 21MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* |QCN6432_2| | |
|
||||
* | M3 Dump | 0x50F00000 | 1MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* |QCN6432_2| | |
|
||||
* | QDSS | 0x51000000 | 1MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* |QCN6432_2| | |
|
||||
* | CALDB | 0x51100000 | 5MB |
|
||||
* +---------+--------------+-------------------------+
|
||||
* | | | |
|
||||
* | MLO | 0x51600000 | 12MB |
|
||||
* +==================================================+
|
||||
* | |
|
||||
* | |
|
||||
* | |
|
||||
* | Rest of memory for Linux |
|
||||
* | |
|
||||
* | |
|
||||
* | |
|
||||
* +==================================================+
|
||||
*/
|
||||
|
||||
reserved-memory {
|
||||
|
||||
/delete-node/ m3_dump@4cc00000;
|
||||
/delete-node/ q6_etr_dump@1;
|
||||
/delete-node/ mlo_global_mem_0@0x4db00000;
|
||||
/delete-node/ wcnss@4a900000;
|
||||
/delete-node/ q6_caldb_region@4ce00000;
|
||||
|
||||
q6_mem_regions: q6_mem_regions@4A900000 {
|
||||
reg = <0x0 0x4a900000 0x0 0x6D00000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_code_data: q6_code_data@4A900000 {
|
||||
reg = <0x0 0x4a900000 0x0 0x1900000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_ipq5332_data: q6_ipq5332_data@4C200000 {
|
||||
reg = <0x0 0x4C200000 0x0 0x1500000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
m3_dump: m3_dump@4D700000 {
|
||||
reg = <0x0 0x4D700000 0x0 0x100000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_etr_region: q6_etr_dump@4D800000 {
|
||||
reg = <0x0 0x4D800000 0x0 0x100000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_ipq5332_caldb: q6_ipq5332_caldb@4D900000 {
|
||||
reg = <0x0 0x4D900000 0x0 0x500000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_qcn6432_data_1: q6_qcn6432_data_1@4DE00000 {
|
||||
reg = <0x0 0x4DE00000 0x0 0x1500000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
m3_dump_qcn6432_1: m3_dump_qcn6432_1@4F300000 {
|
||||
reg = <0x0 0x4F300000 0x0 0x100000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_qcn6432_etr_1: q6_qcn6432_etr_1@4F400000 {
|
||||
reg = <0x0 0x4F400000 0x0 0x100000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_qcn6432_caldb_1: q6_qcn6432_caldb_1@4F500000 {
|
||||
reg = <0x0 0x4F500000 0x0 0x500000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_qcn6432_data_2: q6_qcn6432_data_2@4FA00000 {
|
||||
reg = <0x0 0x4FA00000 0x0 0x1500000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
m3_dump_qcn6432_2: m3_dump_qcn6432_2@50F00000 {
|
||||
reg = <0x0 0x50F00000 0x0 0x100000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_qcn6432_etr_2: q6_qcn6432_etr_2@51000000 {
|
||||
reg = <0x0 0x51000000 0x0 0x100000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
q6_qcn6432_caldb_2: q6_qcn6432_caldb_2@51100000 {
|
||||
reg = <0x0 0x51100000 0x0 0x500000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
mlo_global_mem0: mlo_global_mem_0@51600000 {
|
||||
reg = <0x0 0x51600000 0x0 0xC00000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart0;
|
||||
serial1 = &blsp1_uart1;
|
||||
ethernet0 = "/soc/dp1";
|
||||
ethernet1 = "/soc/dp2";
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0";
|
||||
};
|
||||
|
||||
soc@0 {
|
||||
mdio:mdio@90000 {
|
||||
pinctrl-0 = <&mdio1_pins &mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
/*gpio51 for manhattan reset*/
|
||||
phy-reset-gpio = <&tlmm 22 GPIO_ACTIVE_LOW>;
|
||||
phyaddr_fixup = <0xC90F018>;
|
||||
uniphyaddr_fixup = <0xC90F014>;
|
||||
mdio_clk_fixup; /* MDIO clock sequence fix up flag */
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <1>;
|
||||
fixup;
|
||||
};
|
||||
phy1: ethernet-phy@1 {
|
||||
reg = <2>;
|
||||
fixup;
|
||||
};
|
||||
phy2: ethernet-phy@2 {
|
||||
reg = <3>;
|
||||
fixup;
|
||||
};
|
||||
phy3: ethernet-phy@3 {
|
||||
reg = <4>;
|
||||
fixup;
|
||||
};
|
||||
|
||||
switch0@10 {
|
||||
compatible = "qca,qca8386";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x10>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "cpu";
|
||||
ethernet = <&gmac2>;
|
||||
dsa-tag-protocol = "qca_4b";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan1";
|
||||
phy-handle = <&phy0>;
|
||||
phy-mode = "usxgmii";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan2";
|
||||
phy-handle = <&phy1>;
|
||||
phy-mode = "usxgmii";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan3";
|
||||
phy-handle = <&phy2>;
|
||||
phy-mode = "usxgmii";
|
||||
};
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
label = "lan4";
|
||||
phy-handle = <&phy3>;
|
||||
phy-mode = "usxgmii";
|
||||
};
|
||||
|
||||
port@5 {
|
||||
reg = <5>;
|
||||
forced-speed = <2500>;
|
||||
forced-duplex = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
pwmleds {
|
||||
compatible = "pwm-leds";
|
||||
|
||||
led_power_red: red {
|
||||
label = "pwm:red";
|
||||
pwms = <&pwm 3 1250000>;
|
||||
max-brightness = <160>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
|
||||
led_power_green: green {
|
||||
label = "pwm:green";
|
||||
pwms = <&pwm 2 1250000>;
|
||||
max-brightness = <160>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
|
||||
led_power_blue: blue {
|
||||
label = "pwm:blue";
|
||||
pwms = <&pwm 1 1250000>;
|
||||
max-brightness = <160>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
};
|
||||
|
||||
gpio_keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
button@1 {
|
||||
label = "rst";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
|
||||
linux,input-type = <1>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
ess-instance {
|
||||
num_devices = <0x2>;
|
||||
|
||||
ess-switch@3a000000 {
|
||||
pinctrl-names = "default";
|
||||
switch_cpu_bmp = <0x1>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x2>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x4>; /* wan port bitmap */
|
||||
switch_mac_mode = <0xc>; /* mac mode for uniphy instance0*/
|
||||
switch_mac_mode1 = <0xf>; /* mac mode for uniphy instance1*/
|
||||
switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
forced-speed = <2500>;
|
||||
forced-duplex = <1>;
|
||||
};
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
phy_address = <4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ess-switch1@1 {
|
||||
compatible = "qcom,ess-switch-qca8386";
|
||||
device_id = <1>;
|
||||
switch_access_mode = "mdio";
|
||||
mdio-bus = <&mdio>;
|
||||
switch_mac_mode = <0xc>; /* mac mode for uniphy instance0 */
|
||||
switch_mac_mode1 = <0xc>; /* mac mode1 for uniphy instance1 */
|
||||
switch_cpu_bmp = <0x1>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x0e>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x0>; /* wan port bitmap */
|
||||
// link-polling-required = <0>;
|
||||
fdb_sync = "interrupt";
|
||||
link-intr-gpio = <&tlmm 24 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@0 {
|
||||
port_id = <0>;
|
||||
forced-speed = <2500>;
|
||||
forced-duplex = <1>;
|
||||
};
|
||||
port@1 {
|
||||
port_id = <1>;
|
||||
phy_address = <1>;
|
||||
};
|
||||
port@2 {
|
||||
port_id = <2>;
|
||||
phy_address = <2>;
|
||||
};
|
||||
port@3 {
|
||||
port_id = <3>;
|
||||
phy_address = <3>;
|
||||
};
|
||||
};
|
||||
|
||||
led_source@2 {
|
||||
source = <2>;
|
||||
mode = "normal";
|
||||
speed = "all";
|
||||
blink_en = "enable";
|
||||
active = "high";
|
||||
};
|
||||
led_source@5 {
|
||||
source = <5>;
|
||||
mode = "normal";
|
||||
speed = "all";
|
||||
blink_en = "enable";
|
||||
active = "high";
|
||||
};
|
||||
led_source@8 {
|
||||
source = <8>;
|
||||
mode = "normal";
|
||||
speed = "all";
|
||||
blink_en = "enable";
|
||||
active = "high";
|
||||
};
|
||||
led_source@11 {
|
||||
source = <11>;
|
||||
mode = "normal";
|
||||
speed = "all";
|
||||
blink_en = "enable";
|
||||
active = "high";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
dp1 {
|
||||
device_type = "network";
|
||||
compatible = "qcom,nss-dp";
|
||||
qcom,id = <2>;
|
||||
reg = <0x3a504000 0x4000>;
|
||||
qcom,mactype = <1>;
|
||||
local-mac-address = [000000000000];
|
||||
qcom,mht-dev = <1>;
|
||||
qcom,is_switch_connected = <1>;
|
||||
qcom,ppe-offload-disabled = <1>;
|
||||
phy-mode = "sgmii";
|
||||
};
|
||||
|
||||
gmac2:dp2 {
|
||||
device_type = "network";
|
||||
compatible = "qcom,nss-dp";
|
||||
qcom,id = <1>;
|
||||
reg = <0x3a500000 0x4000>;
|
||||
qcom,mactype = <1>;
|
||||
local-mac-address = [000000000000];
|
||||
phy-mode = "sgmii";
|
||||
qcom,mht-dev = <1>;
|
||||
qcom,is_switch_connected = <1>;
|
||||
qcom,ppe-offload-disabled = <1>;
|
||||
};
|
||||
|
||||
/* EDMA host driver configuration for the board */
|
||||
edma@3ab00000 {
|
||||
qcom,txdesc-ring-start = <4>; /* Tx desc ring start ID */
|
||||
qcom,txdesc-rings = <12>; /* Total number of Tx desc rings to be provisioned */
|
||||
qcom,mht-txdesc-rings = <8>; /* Extra Tx desc rings to be provisioned for MHT SW ports */
|
||||
qcom,txcmpl-ring-start = <4>; /* Tx complete ring start ID */
|
||||
qcom,txcmpl-rings = <12>; /* Total number of Tx complete rings to be provisioned */
|
||||
qcom,mht-txcmpl-rings = <8>; /* Extra Tx complete rings to be provisioned for mht sw ports. */
|
||||
qcom,rxfill-ring-start = <4>; /* Rx fill ring start ID */
|
||||
qcom,rxfill-rings = <4>; /* Total number of Rx fill rings to be provisioned */
|
||||
qcom,rxdesc-ring-start = <12>; /* Rx desc ring start ID */
|
||||
qcom,rxdesc-rings = <4>; /* Total number of Rx desc rings to be provisioned */
|
||||
qcom,rx-page-mode = <0>; /* Rx fill ring page mode */
|
||||
qcom,tx-map-priority-level = <1>; /* Tx priority level per port */
|
||||
qcom,rx-map-priority-level = <1>; /* Rx priority level per core */
|
||||
qcom,ppeds-num = <2>; /* Number of PPEDS nodes */
|
||||
/* PPE-DS node format: <Rx-fill Tx-cmpl Rx Tx Queue-base Queue-count> */
|
||||
qcom,ppeds-map = <1 1 1 1 32 8>, /* PPEDS Node#0 ring and queue map */
|
||||
<2 2 2 2 40 8>; /* PPEDS Node#1 ring and queue map */
|
||||
qcom,txdesc-map = <8 9 10 11>, /* Port0 per-core Tx ring map */
|
||||
<12 13 14 15>, /* MHT-Port1 per-core Tx ring map */
|
||||
<4 5 6 7>, /* MHT-Port2 per-core Tx ring map/packets from vp*/
|
||||
<16 17 18 19>, /* MHT-Port3 per-core Tx ring map */
|
||||
<20 21 22 23>; /* MHT-Port4 per-core Tx ring map */
|
||||
qcom,txdesc-fc-grp-map = <1 2 3 4 5>; /* Per GMAC flow control group map */
|
||||
qcom,rxfill-map = <4 5 6 7>; /* Per-core Rx fill ring map */
|
||||
qcom,rxdesc-map = <12 13 14 15>; /* Per-core Rx desc ring map */
|
||||
qcom,rx-queue-start = <0>; /* Rx queue start */
|
||||
qcom,rx-ring-queue-map = <0 8 16 24>, /* Priority 0 queues per-core Rx ring map */
|
||||
<1 9 17 25>, /* Priority 1 queues per-core Rx ring map */
|
||||
<2 10 18 26>, /* Priority 2 queues per-core Rx ring map */
|
||||
<3 11 19 27>, /* Priority 3 queues per-core Rx ring map */
|
||||
<4 12 20 28>, /* Priority 4 queues per-core Rx ring map */
|
||||
<5 13 21 29>, /* Priority 5 queues per-core Rx ring map */
|
||||
<6 14 22 30>, /* Priority 6 queues per-core Rx ring map */
|
||||
<7 15 23 31>; /* Priority 7 queues per-core Rx ring map */
|
||||
interrupts = <0 163 4>, /* Tx complete ring id #4 IRQ info */
|
||||
<0 164 4>, /* Tx complete ring id #5 IRQ info */
|
||||
<0 165 4>, /* Tx complete ring id #6 IRQ info */
|
||||
<0 166 4>, /* Tx complete ring id #7 IRQ info */
|
||||
<0 167 4>, /* Tx complete ring id #8 IRQ info */
|
||||
<0 168 4>, /* Tx complete ring id #9 IRQ info */
|
||||
<0 169 4>, /* Tx complete ring id #10 IRQ info */
|
||||
<0 170 4>, /* Tx complete ring id #11 IRQ info */
|
||||
<0 171 4>, /* Tx complete ring id #12 IRQ info */
|
||||
<0 172 4>, /* Tx complete ring id #13 IRQ info */
|
||||
<0 173 4>, /* Tx complete ring id #14 IRQ info */
|
||||
<0 174 4>, /* Tx complete ring id #15 IRQ info */
|
||||
<0 139 4>, /* Rx desc ring id #12 IRQ info */
|
||||
<0 140 4>, /* Rx desc ring id #13 IRQ info */
|
||||
<0 141 4>, /* Rx desc ring id #14 IRQ info */
|
||||
<0 142 4>, /* Rx desc ring id #15 IRQ info */
|
||||
<0 191 4>, /* Misc error IRQ info */
|
||||
<0 160 4>, /* PPEDS Node #1(TxComp ring id #1) TxComplete IRQ info */
|
||||
<0 128 4>, /* PPEDS Node #1(Rx Desc ring id #1) Rx Desc IRQ info */
|
||||
<0 152 4>, /* PPEDS Node #1(RxFill Desc ring id #1) Rx Fill IRQ info */
|
||||
<0 161 4>, /* PPEDS Node #2(TxComp ring id #2) TxComplete IRQ info */
|
||||
<0 129 4>, /* PPEDS Node #2(Rx Desc ring id #2) Rx Desc IRQ info */
|
||||
<0 153 4>, /* PPEDS Node #2(RxFill Desc ring id #2) Rx Fill IRQ info */
|
||||
<0 175 4>, /* MHT port Tx complete ring id #16 IRQ info */
|
||||
<0 176 4>, /* MHT port Tx complete ring id #17 IRQ info */
|
||||
<0 177 4>, /* MHT port Tx complete ring id #18 IRQ info */
|
||||
<0 178 4>, /* MHT port Tx complete ring id #19 IRQ info */
|
||||
<0 179 4>, /* MHT port Tx complete ring id #20 IRQ info */
|
||||
<0 180 4>, /* MHT port Tx complete ring id #21 IRQ info */
|
||||
<0 181 4>, /* MHT port Tx complete ring id #22 IRQ info */
|
||||
<0 182 4>; /* MHT port Tx complete ring id #23 IRQ info */
|
||||
};
|
||||
|
||||
wsi: wsi {
|
||||
id = <0>;
|
||||
num_chip = <3>;
|
||||
status = "okay";
|
||||
chip_info = <0 2 1 2>,
|
||||
<1 2 2 0>,
|
||||
<2 2 0 1>;
|
||||
};
|
||||
|
||||
q6v5_wcss: remoteproc@d100000 {
|
||||
boot-args = <0x1 0x4 0x3 0x1 0x2f 0x2>,
|
||||
<0x1 0x4 0x4 0x2 0x2c 0x2>;
|
||||
memory-region = <&q6_mem_regions>,
|
||||
<&mlo_global_mem0>;
|
||||
|
||||
/delete-node/ remoteproc_pd1;
|
||||
/delete-node/ remoteproc_pd2;
|
||||
/delete-node/ remoteproc_pd3;
|
||||
|
||||
q6_wcss_pd4: remoteproc_pd4 {
|
||||
compatible = "qcom,ipq5332-mpd-upd-text";
|
||||
firmware = "IPQ5332/q6_fw4.mdt";
|
||||
|
||||
q6_wcss_pd1: remoteproc_pd1 {
|
||||
compatible = "qcom,ipq5332-wcss-ahb-mpd";
|
||||
firmware = "IPQ5332/q6_fw1.mdt";
|
||||
m3_firmware = "IPQ5332/iu_fw.mdt";
|
||||
interrupts-extended = <&wcss_smp2p_in 8 0>,
|
||||
<&wcss_smp2p_in 9 0>,
|
||||
<&wcss_smp2p_in 12 0>,
|
||||
<&wcss_smp2p_in 11 0>;
|
||||
interrupt-names = "fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states = <&wcss_smp2p_out 8>,
|
||||
<&wcss_smp2p_out 9>,
|
||||
<&wcss_smp2p_out 10>;
|
||||
qcom,smem-state-names = "shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
};
|
||||
|
||||
q6_wcss_pd2: remoteproc_pd2 {
|
||||
compatible = "qcom,ipq5332-wcss-pcie-mpd";
|
||||
firmware = "IPQ5332/q6_fw2.mdt";
|
||||
m3_firmware = "qcn6432/iu_fw.mdt";
|
||||
interrupts-extended = <&wcss_smp2p_in 16 0>,
|
||||
<&wcss_smp2p_in 17 0>,
|
||||
<&wcss_smp2p_in 20 0>,
|
||||
<&wcss_smp2p_in 19 0>;
|
||||
interrupt-names = "fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states = <&wcss_smp2p_out 16>,
|
||||
<&wcss_smp2p_out 17>,
|
||||
<&wcss_smp2p_out 18>;
|
||||
qcom,smem-state-names = "shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
q6_wcss_pd3: remoteproc_pd3 {
|
||||
compatible = "qcom,ipq5332-wcss-pcie-mpd";
|
||||
firmware = "IPQ5332/q6_fw3.mdt";
|
||||
interrupts-extended = <&wcss_smp2p_in 24 0>,
|
||||
<&wcss_smp2p_in 25 0>,
|
||||
<&wcss_smp2p_in 28 0>,
|
||||
<&wcss_smp2p_in 27 0>;
|
||||
interrupt-names = "fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states = <&wcss_smp2p_out 24>,
|
||||
<&wcss_smp2p_out 25>,
|
||||
<&wcss_smp2p_out 26>;
|
||||
qcom,smem-state-names = "shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
status = "ok";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart0 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_1_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sleep_clk {
|
||||
clock-frequency = <32000>;
|
||||
};
|
||||
|
||||
&xo {
|
||||
clock-frequency = <24000000>;
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
pinctrl-0 = <&qspi_default_state>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
nandcs@0 {
|
||||
reg = <0>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
nand-ecc-strength = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-bus-width = <8>;
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
qspi_default_state: qspi-default-state {
|
||||
qspi_clock {
|
||||
pins = "gpio13";
|
||||
function = "qspi_clk";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
qspi_cs {
|
||||
pins = "gpio12";
|
||||
function = "qspi_cs";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
qspi_data {
|
||||
pins = "gpio8", "gpio9", "gpio10", "gpio11";
|
||||
function = "qspi_data";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
pwm_pins: pwm_pinmux {
|
||||
/* PWM LED GREEN */
|
||||
mux_1 {
|
||||
pins = "gpio30";
|
||||
function = "pwm1";
|
||||
drive-strength = <8>;
|
||||
};
|
||||
/* PWM LED BLUE */
|
||||
mux_2 {
|
||||
pins = "gpio31";
|
||||
function = "pwm1";
|
||||
drive-strength = <8>;
|
||||
};
|
||||
/* PWM LED RED */
|
||||
mux_3 {
|
||||
pins = "gpio29";
|
||||
function = "pwm1";
|
||||
drive-strength = <8>;
|
||||
};
|
||||
};
|
||||
|
||||
serial_1_pins: serial1-pinmux {
|
||||
pins = "gpio33", "gpio34", "gpio35", "gpio36";
|
||||
function = "blsp1_uart2";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
|
||||
button_pins: button-state {
|
||||
pins = "gpio21";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
spi_0_data_clk_pins: spi-0-data-clk-state {
|
||||
pins = "gpio14", "gpio15", "gpio16";
|
||||
function = "blsp0_spi";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
spi_0_cs_pins: spi-0-cs-state {
|
||||
pins = "gpio17";
|
||||
function = "blsp0_spi";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio1_pins: mdio1-state {
|
||||
mux_0 {
|
||||
pins = "gpio27";
|
||||
function = "mdc1";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
mux_1 {
|
||||
pins = "gpio28";
|
||||
function = "mdio1";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&license_manager {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-0 = <&pwm_pins>;
|
||||
used-pwm-indices = <1>, <1>, <0>, <1>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hs_m31phy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
qcom,multipd_arch;
|
||||
qcom,rproc = <&q6_wcss_pd1>;
|
||||
qcom,rproc_rpd = <&q6v5_wcss>;
|
||||
qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
|
||||
qcom,tgt-mem-mode = <0>;
|
||||
qcom,bdf-addr = <0x4C200000 0x4C200000 0x4C200000 0x0 0x0 0x0>;
|
||||
qcom,caldb-addr = <0x4D900000 0x4D900000 0x4D900000 0x0 0x0 0x0>;
|
||||
qcom,caldb-size = <0x500000>;
|
||||
qcom,board_id = <0x41>;
|
||||
mem-region = <&q6_ipq5332_data>;
|
||||
memory-region = <&q6_ipq5332_data>;
|
||||
qcom,wsi = <&wsi>;
|
||||
qcom,wsi_index = <0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
qcom,multipd_arch;
|
||||
qcom,rproc = <&q6_wcss_pd2>;
|
||||
qcom,rproc_rpd = <&q6v5_wcss>;
|
||||
qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
|
||||
qcom,tgt-mem-mode = <0>;
|
||||
qcom,bdf-addr = <0x4DE00000 0x4DE00000 0x4DE00000 0x0 0x0 0x0>;
|
||||
qcom,caldb-addr = <0x4F500000 0x4F500000 0x4F500000 0x0 0x0 0x0>;
|
||||
qcom,umac-irq-reset-addr = <0x20000884>;
|
||||
qcom,caldb-size = <0x500000>;
|
||||
qcom,board_id = <0x061>;
|
||||
mem-region = <&q6_qcn6432_data_1>;
|
||||
memory-region = <&q6_qcn6432_data_1>;
|
||||
qcom,wsi = <&wsi>;
|
||||
qcom,wsi_index = <1>;
|
||||
status = "okay";
|
||||
interrupts = <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>;
|
||||
interrupt-names = "umac_reset";
|
||||
};
|
||||
|
||||
&wifi2 {
|
||||
qcom,multipd_arch;
|
||||
qcom,rproc = <&q6_wcss_pd3>;
|
||||
qcom,rproc_rpd = <&q6v5_wcss>;
|
||||
qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
|
||||
qcom,tgt-mem-mode = <0>;
|
||||
qcom,bdf-addr = <0x4FA00000 0x4FA00000 0x4FA00000 0x0 0x0 0x0>;
|
||||
qcom,caldb-addr = <0x51100000 0x51100000 0x51100000 0x0 0x0 0x0>;
|
||||
qcom,umac-irq-reset-addr = <0x18000884>;
|
||||
qcom,caldb-size = <0x500000>;
|
||||
qcom,board_id = <0x0b1>;
|
||||
mem-region = <&q6_qcn6432_data_2>;
|
||||
memory-region = <&q6_qcn6432_data_2>;
|
||||
qcom,wsi = <&wsi>;
|
||||
qcom,wsi_index = <2>;
|
||||
status = "okay";
|
||||
interrupts = <GIC_SPI 410 IRQ_TYPE_EDGE_RISING>;
|
||||
interrupt-names = "umac_reset";
|
||||
};
|
||||
@@ -166,10 +166,10 @@
|
||||
serial1 = &blsp1_uart1;
|
||||
ethernet0 = "/soc/dp1";
|
||||
ethernet1 = "/soc/dp2";
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
};
|
||||
|
||||
chosen {
|
||||
@@ -261,21 +261,21 @@
|
||||
pwmleds {
|
||||
compatible = "pwm-leds";
|
||||
|
||||
red {
|
||||
led_power_red: red {
|
||||
label = "pwm:red";
|
||||
pwms = <&pwm 3 1250000>;
|
||||
max-brightness = <160>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
|
||||
green {
|
||||
led_power_green: green {
|
||||
label = "pwm:green";
|
||||
pwms = <&pwm 2 1250000>;
|
||||
max-brightness = <160>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
|
||||
led_power: blue {
|
||||
led_power_blue: blue {
|
||||
label = "pwm:blue";
|
||||
pwms = <&pwm 1 1250000>;
|
||||
max-brightness = <160>;
|
||||
@@ -307,7 +307,7 @@
|
||||
switch_lan_bmp = <0x2>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x4>; /* wan port bitmap */
|
||||
switch_mac_mode = <0xc>; /* mac mode for uniphy instance0*/
|
||||
switch_mac_mode1 = <0xc>; /* mac mode for uniphy instance1*/
|
||||
switch_mac_mode1 = <0xf>; /* mac mode for uniphy instance1*/
|
||||
switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
|
||||
|
||||
qcom,port_phyinfo {
|
||||
@@ -318,8 +318,7 @@
|
||||
};
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
forced-speed = <2500>;
|
||||
forced-duplex = <1>;
|
||||
phy_address = <4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
@@ -331,9 +330,9 @@
|
||||
mdio-bus = <&mdio>;
|
||||
switch_mac_mode = <0xc>; /* mac mode for uniphy instance0 */
|
||||
switch_mac_mode1 = <0xc>; /* mac mode1 for uniphy instance1 */
|
||||
switch_cpu_bmp = <0x21>; /* cpu port bitmap */
|
||||
switch_cpu_bmp = <0x1>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x0e>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x10>; /* wan port bitmap */
|
||||
switch_wan_bmp = <0x0>; /* wan port bitmap */
|
||||
// link-polling-required = <0>;
|
||||
fdb_sync = "interrupt";
|
||||
link-intr-gpio = <&tlmm 24 GPIO_ACTIVE_HIGH>;
|
||||
@@ -356,15 +355,6 @@
|
||||
port_id = <3>;
|
||||
phy_address = <3>;
|
||||
};
|
||||
port@4 {
|
||||
port_id = <4>;
|
||||
phy_address = <4>;
|
||||
};
|
||||
port@5 {
|
||||
port_id = <5>;
|
||||
forced-speed = <2500>;
|
||||
forced-duplex = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
led_source@2 {
|
||||
|
||||
@@ -77,3 +77,17 @@ define Device/cig_wf189w
|
||||
DEVICE_PACKAGES := ath12k-wifi-cig-wf189w ath12k-firmware-ipq5332-peb-peb
|
||||
endef
|
||||
TARGET_DEVICES += cig_wf189w
|
||||
|
||||
|
||||
define Device/cig_wf189h
|
||||
DEVICE_TITLE := CIG WF189H
|
||||
DEVICE_DTS := ipq5332-cig-wf189h
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_DTS_CONFIG := config@mi04.1
|
||||
IMAGES := sysupgrade.tar nand-factory.bin nand-factory.ubi
|
||||
IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
|
||||
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
|
||||
IMAGE/nand-factory.ubi := append-ubi
|
||||
DEVICE_PACKAGES := ath12k-wifi-cig-wf189h ath12k-firmware-ipq5332-peb-peb
|
||||
endef
|
||||
TARGET_DEVICES += cig_wf189h
|
||||
|
||||
@@ -79,6 +79,8 @@ hfcl,ion4xe)
|
||||
;;
|
||||
cig,wf186w|\
|
||||
cig,wf189|\
|
||||
cig,wf189w|\
|
||||
cig,wf189h|\
|
||||
cig,wf186h|\
|
||||
yuncore,ax840|\
|
||||
yuncore,fap655)
|
||||
|
||||
@@ -12,3 +12,4 @@ include:
|
||||
packages:
|
||||
- ipq53xx
|
||||
- ftm
|
||||
- qca-ssdk-shell
|
||||
|
||||
14
profiles/cig_wf189h.yml
Normal file
14
profiles/cig_wf189h.yml
Normal file
@@ -0,0 +1,14 @@
|
||||
---
|
||||
profile: cig_wf189h
|
||||
target: ipq53xx
|
||||
subtarget: generic
|
||||
description: Build image for the CIG WF189h
|
||||
image: bin/targets/ipq53xx/generic/openwrt-ipq53xx-cig_wf189h-squashfs-sysupgrade.tar
|
||||
feeds:
|
||||
- name: qca
|
||||
path: ../../feeds/qca-wifi-7
|
||||
include:
|
||||
- ucentral-ap
|
||||
packages:
|
||||
- ipq53xx
|
||||
- qca-ssdk-shell
|
||||
Reference in New Issue
Block a user