ipq95xx: Update phy driver for EAP105 LAN port

Fixes: WIFI-14171
Signed-off-by: Tanya Singh <tanya_singh@accton.com>

feeds/ipq95xx/ipq53xx/base-files/etc/init.d/rtk_eth_fix

@@ -0,0 +1,86 @@
+#!/bin/sh /etc/rc.common
+# Copyright (C) 2007 OpenWrt.org
+
+START=94
+USE_PROCD=1
+
+. /lib/functions.sh
+
+eap105_eth_fix() {
+	#ethernet reset
+	echo 481 > /sys/class/gpio/export
+	echo "out" > /sys/class/gpio/gpio481/direction
+	echo 0 > /sys/class/gpio/gpio481/value
+	echo 1 > /sys/class/gpio/gpio481/value
+
+	#eth1 Fix RE Fail
+	sleep 1
+	ssdk_sh debug phy set 0x2 0x1f 0x0A43
+	ssdk_sh debug phy set 0x2 0x19 0x0862
+	ssdk_sh debug phy set 0x2 0x1f 0x0000
+	ssdk_sh debug phy set 0x2 0x0 0x9200
+
+	#eth1 10/100M detect led flash setup
+	ssdk_sh debug phy set 0x2 0x1f 0x0d04
+	ssdk_sh debug phy set 0x2 0x10 0x6E51
+
+	#eth0 5G detect led flash setup
+	ssdk_sh debug phy set 0x1 0xd 0x1f
+	ssdk_sh debug phy set 0x1 0xe 0xd032
+	ssdk_sh debug phy set 0x1 0xd 0x401f
+	ssdk_sh debug phy set 0x1 0xe 0x1e7
+
+	ssdk_sh debug phy set 0x1 0xd 0x1f
+	ssdk_sh debug phy set 0x1 0xe 0xd040
+	ssdk_sh debug phy set 0x1 0xd 0x401f
+	ssdk_sh debug phy set 0x1 0xe 0x393f
+
+	#eth0 Fix USXGMII
+	ssdk_sh debug phy set 0x1 0x601E7588 0x05D8
+	ssdk_sh debug phy set 0x1 0x601E7589 0x2100
+	ssdk_sh debug phy set 0x1 0x601E7587 0x0003
+
+	count=0
+	while [ 1 ]
+	do
+		date
+		if [ $(($(echo $(echo $(ssdk_sh debug phy get 0x1 0x601E7587) | cut -d':' -f2) | cut -d' ' -f1) & 1)) -eq 0 ]; then
+			echo > /tmp/Pre-emphasis-PASS
+			break
+		fi
+		count=$(($count+1))
+		if [ $count -eq 10 ]; then
+			echo > /tmp/Pre-emphasis-FAIL
+			break
+		fi
+		sleep 1
+	done
+
+	ssdk_sh debug phy set 0x1 0x601E7588 0x05D7
+	ssdk_sh debug phy set 0x1 0x601E7589 0x2180
+	ssdk_sh debug phy set 0x1 0x601E7587 0x0003
+
+	count=0
+	while [ 1 ]
+	do
+		date
+		if [ $(($(echo $(echo $(ssdk_sh debug phy get 0x1 0x601E7587) | cut -d':' -f2) | cut -d' ' -f1) & 1)) -eq 0 ]; then
+			echo > /tmp/Amp-PASS
+			break
+		fi
+		count=$(($count+1))
+		if [ $count -eq 10 ]; then
+			echo > /tmp/Amp-FAIL
+			break
+		fi
+		sleep 1
+	done
+}
+
+start_service() {
+	case "$(board_name)" in
+	"edgecore,eap105")
+		eap105_eth_fix
+		;;
+	esac
+}

feeds/ipq95xx/ipq53xx/files/arch/arm64/boot/dts/qcom/ipq5332-edgecore-eap105.dts

@@ -434,7 +434,7 @@
 	memory-region = <&q6_region>;
 	qcom,wsi = <&wsi>;
 #endif
-	qcom,board_id = <0x16>;
+	qcom,board_id = <0x12>;
 	status = "ok";
 };
 

feeds/ipq95xx/ipq53xx/files/drivers/net/phy/rtk/phy_rtl8251b_patch.c

@@ -2019,14 +2019,14 @@ int32 rtl8251b_phy_init(struct phy_device *phydev)
 {
     BOOL status = FAILURE;
     UINT16 i = 0;   /* SW_SDK: use UINT16 instead of UINT8, for MMD_REG array may over 255 entries */
-    UINT16 phydata = 0;
+    UINT16 phydata = 0, rev_num = 0, mod_num = 0;
     const UINT16 patchver = 0x0014, patchaddr = 0x8023;
 
     status = Rtl8251b_wait_for_bit(phydev, MMD_VEND2, 0xA420, 0x3, 1, 100);
     if (status != SUCCESS) {
         goto exit;
     }
-#if 0
+#if 1
     status = MmdPhyRead(phydev, MMD_PMAPMD, 0x03, &phydata);
     if (status != SUCCESS)
         goto exit;
@@ -2038,7 +2038,10 @@ int32 rtl8251b_phy_init(struct phy_device *phydev)
         osal_printf("rtl8251b and go init flow...\n");
     }
     else{
-        osal_printf("Not rtl8251b and skip init flow...id = %x \n",phydata);
+        if (phydata == 0xc868)
+            osal_printf("Realtek chip is RTL8251B-VB-CG\n");
+        else
+            osal_printf("Not rtl8251b and skip init flow...id = %x \n",phydata);
         goto exit;
     }
 #endif

profiles/edgecore_eap105.yml

@@ -9,6 +9,7 @@ feeds:
     path: ../../feeds/ipq95xx
 packages:
   - ipq53xx
+  - qca-ssdk-shell
 include:
   - ucentral-ap
 diffconfig: |