A scenario was seen where UCI config was not flushed to disk before
an AP power-cycle after uci-defaults was completed. Since these
scripts are deleted after being ran once, there is no way to recover
without a factory reset.
Adding this sync operation proved to help avoid this situation from
happening
Signed-off-by: Paul White <paul@shasta.cloud>
This patch enhances WPA3 encryption support in netifd by introducing GCMP-256
cipher handling for wireless interfaces operating on the 6 GHz band with HE/EHT
modes.
Fixes: WIFI-14594
Signed-off-by: Marek Kwaczynski <marek@shasta.cloud>
1. For EAP112 LTE module (Quectel EM60 series), when username and password is configured, it is required to update the context with the QICSGP AT command.
2. Use a handler function to check if the AT command is stuck and retry.
Fixes: WIFI-14545
Signed-off-by: Sebastian Huang <sebastian_huang@accton.com>
1. porting MorseMicro HaLow driver to support HaLow on EAP112
2. Only support FCC regulation because of hardware limitation
3. Add /etc/init.d/halow-gpio-reset to initialize HaLow chip in early stage
4. Add /etc/uci-defaults/aaa-fix-phy0-to-morse to correct the default uci for HaLow radio.
Signed-off-by: Ian Chen <ian77_chen@accton.com>
Specifications:
SoC: MediaTek MT7981BA
RF Chipset: MT7976DA @2.4GHz 2T2R
MT7976DA @5ghz 2T2R
RAM: 512MB DDR4 RAM
Flash: SPI-NAND 256 MiB
Ethernet: 2 x 1GbE PHY
Reset Button
Power Source: DC IN 12v, Standard PoE 802.3af/at
LED Indicator: 1 x single color LED (GPIO Control)
Fixes: WIFI-14312
Signed-off-by: steven.lin <steven.lin@senao.com>
Specifications:
SoC: MediaTek MT7986A
RF Chipset: MT7976G @2.4GHz 4T4R
MT7976A @5ghz 4T4R
RAM: 1GB DDR4 RAM (2x 512MB)
Flash: SPI-NAND 256 MiB
Ethernet: 1x 2.5GbE PHY
Reset Button
Power Source: DC IN 12v, Standard PoE 802.3af/at
LED Indicator: 4 x single color LED (GPIO Control)
Fixes: WIFI-13983
Signed-off-by: Steven Lin <steven.lin@senao.com>
ubootenv_size is computed dynamically similar to ipq807x.
This resolves the issue where fw_setenv fails with the following error.
MTD erase error on /dev/mtd13: Invalid argument
Error: can't write fw_env to flash
Signed-off-by: Venkat Chimata <venkata@shasta.cloud>
This commit is an improvement over previous
commit 3598a243b3 which added a
fix for traffic disruption when vlan id of the lan port is
changed on devices with internal switches such as fap655,
CIG_WF186w,EAP-104.
This commit reconfigures the vlans for the mpsk clients on the
switch using the ucentral-event subsystem by tracking the
netifd_add events.
Fixes: WIFI-13797
Signed-off-by: joydeepbenison <joydeep.ghosh@benisontech.com>
Fixes WIFI-13428 : traffic disruption for FAP655,CIG_WF186w,EAP-104 for MPSK Clients when vlan id
of the lan port is modified . This Commit configures the dynamic vlans
on the switch of fap655 again after reset.
Signed-off-by: joydeepbenison <joydeep.ghosh@benisontech.com>
