base-files: boot: add sync after uci-defaults

A scenario was seen where UCI config was not flushed to disk before
an AP power-cycle after uci-defaults was completed.  Since these
scripts are deleted after being ran once, there is no way to recover
without a factory reset.

Adding this sync operation proved to help avoid this situation from
happening

Signed-off-by: Paul White <paul@shasta.cloud>

feeds/ipq807x_v5.4/ipq50xx/base-files/lib/upgrade/platform.sh

@@ -107,12 +107,25 @@ platform_do_upgrade() {
 
 	board=$(board_name)
 	case $board in
-	glinet,b3000|\
 	edgecore,oap101|\
 	edgecore,oap101-6e|\
 	edgecore,oap101e|\
 	edgecore,oap101e-6e|\
 	edgecore,eap104)
+		if [ "$(find_mtd_chardev rootfs)" ]; then
+			CI_UBIPART="rootfs"
+		else
+			if grep -q rootfs1 /proc/cmdline; then
+				CI_UBIPART="rootfs2"
+				CI_FWSETENV="active 2"
+			else
+				CI_UBIPART="rootfs1"
+				CI_FWSETENV="active 1"
+			fi
+		fi
+		nand_upgrade_tar "$1"
+		;;
+	glinet,b3000)
 		CI_UBIPART="rootfs1"
 		[ "$(find_mtd_chardev rootfs)" ] && CI_UBIPART="rootfs"
 		nand_upgrade_tar "$1"

feeds/mediatek-sdk/mediatek/mt7981/base-files/etc/hotplug.d/iface/99-mtk-sr-scene-cond

@@ -34,13 +34,11 @@ case "$board" in
 
         if [ -f "$phy0_file" ]; then
             check_phy0=$(cat $phy0_file)
-            echo "check_phy0 = $check_phy0"
             [ "$check_phy0" == 0 ] && echo 1 > $phy0_file
         fi
 
         if [ -f "$phy1_file" ]; then
             check_phy1=$(cat $phy1_file)
-            echo "check_phy1 = $check_phy1"
             [ "$check_phy1" == 0 ] && echo 1 > $phy1_file
         fi
 

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap7110c-341x.dts

@@ -31,6 +31,20 @@
 		stdout-path = "serial0";
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+	};
+
 	soc@0 {
 		mdio:mdio@90000 {
 			pinctrl-0 = <&mdio1_pins>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap750e-h.dts

@@ -190,6 +190,14 @@
 		/delete-node/ wcnss@4a900000;
 		/delete-node/ q6_caldb_region@4ce00000;
 
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
 		q6_mem_regions: q6_mem_regions@4A900000  {
 		        no-map;
 		        reg = <0x0 0x4A900000 0x0 0x5100000>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap750e-s.dts

@@ -190,6 +190,14 @@
 		/delete-node/ wcnss@4a900000;
 		/delete-node/ q6_caldb_region@4ce00000;
 
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
 		q6_mem_regions: q6_mem_regions@4A900000  {
 		        no-map;
 		        reg = <0x0 0x4A900000 0x0 0x5100000>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap750w-311a.dts

@@ -190,6 +190,14 @@
 		/delete-node/ wcnss@4a900000;
 		/delete-node/ q6_caldb_region@4ce00000;
 
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
 		q6_mem_regions: q6_mem_regions@4A900000  {
 		        no-map;
 		        reg = <0x0 0x4A900000 0x0 0x5100000>;

feeds/tip/certificates/files/usr/bin/mount_certs

@@ -45,7 +45,8 @@ sonicfi,rap7*)
 		fi
 	fi
 	;;
-udaya,a5-id2)
+udaya,a5-id2|\
+yuncore,ax820)
 	mtd=$(find_mtd_index certificates)
 	if [ "$(head -c 4 /dev/mtd$mtd)" == "hsqs" ]; then
 		mount -t squashfs /dev/mtdblock$mtd /mnt
@@ -65,7 +66,7 @@ sonicfi,rap6*)
 		cp /mnt/* /certificates
 		umount /mnt
 	fi
-	part=$(tar_part_lookup "0:BOOTCONFIG" "0:BOOTCONFIG1")
+	part=$(tar_part_lookup "devinfo" "certificates")
 	if [ -n "$part" ]; then
 		mtd=$(find_mtd_index $part)
 		[ -n "$mtd" ] && tar xf /dev/mtdblock$mtd -C /certificates

feeds/tip/certificates/files/usr/bin/store_certs

@@ -21,7 +21,8 @@ sonicfi,rap7110c-341x)
 	mmc_dev=$(echo $(find_mmc_part $part) | sed 's/^.\{5\}//')
 	dd if=/tmp/certs.tar of=/dev/$mmc_dev
 	;;
-udaya,a5-id2)
+udaya,a5-id2|\
+yuncore,ax820)
 	cd /certificates
 	tar cf /tmp/certs.tar .
 	part=$(tar_part_lookup "insta1" "insta2")
@@ -32,7 +33,7 @@ sonicfi,rap6*)
 	if [ "$(fw_printenv -n store_certs_disabled)" != "1" ]; then
 		cd /certificates
 		tar cf /tmp/certs.tar .
-		part=$(tar_part_lookup "0:BOOTCONFIG" "0:BOOTCONFIG1")
+		part=$(tar_part_lookup "devinfo" "certificates")
 		mtd=$(find_mtd_index $part)
 		block_size=$(cat /sys/class/mtd/mtd$mtd/size)
 		dd if=/tmp/certs.tar of=/tmp/certs_pad.tar bs=$block_size conv=sync

feeds/tip/cloud_discovery/files/etc/init.d/cloud_discover

@@ -22,6 +22,19 @@ start_service() {
 	[ "$valid" == "true" ] || 
 		/usr/share/ucentral/ucentral.uc /etc/ucentral/ucentral.cfg.0000000001 > /dev/null
 
+	est_client check
+	[ $? -eq 1 ] && {
+		logger ERROR
+		logger ERROR
+		logger ERROR
+		logger The certificate used has a CN that does not match the serial of the device
+		echo The certificate used has a CN that does not match the serial of the device
+		logger ERROR
+		logger ERROR
+		logger ERROR
+		return
+	}
+
 	procd_open_instance
 	procd_set_param command "$PROG"
 	procd_set_param respawn

feeds/tip/cloud_discovery/files/usr/bin/est_client

@@ -4,6 +4,7 @@
 
 import { ulog_open, ulog, ULOG_SYSLOG, ULOG_STDIO, LOG_DAEMON, LOG_INFO } from 'log';
 import * as fs from 'fs';
+import * as libuci from 'uci';
 
 let store_operational_pem = false;
 let store_operational_ca = false;
@@ -139,6 +140,9 @@ function load_operational_ca() {
 }
 
 function fwtool() {
+	if (!fs.stat('/etc/ucentral/cert.pem'))
+		return 0;
+
 	let pipe = fs.popen(`openssl x509 -in /etc/ucentral/cert.pem -noout -issuer`);
 	let issuer = pipe.read("all");
 	pipe.close();
@@ -163,6 +167,20 @@ function fwtool() {
 	return 0;
 }
 
+function check_cert() {
+	if (!fs.stat('/etc/ucentral/cert.pem'))
+		return 0;
+	let pipe = fs.popen("openssl x509 -in /etc/ucentral/cert.pem  -noout -subject -nameopt multiline | grep commonName | awk '{ print $3 }'");
+	let cn = pipe.read("all");
+	pipe.close();
+	if (!cn)
+		return 0;
+	cn = lc(trim(cn));
+	let uci = libuci.cursor();
+	let serial = uci.get('ucentral', 'config', 'serial');
+	return cn != serial;
+}
+
 switch(ARGV[0]) {
 case 'enroll':
 	let ret = simpleenroll();
@@ -184,4 +202,7 @@ case 'reenroll':
 
 case 'fwtool':
 	exit(fwtool());
+
+case 'check':
+	exit(check_cert());
 }

feeds/ucentral/rtty/files/rtty.init

@@ -51,7 +51,7 @@ start_rtty() {
 	procd_set_param command $BIN -h $host -I "$id" -a
 	[ -n "$port" ] && procd_append_param command -p "$port"
 	[ -n "$description" ] && procd_append_param command -d "$description"
-	[ "$ssl" = "1" ] && procd_append_param command -s -c /etc/ucentral/opertional.pem -k /etc/ucentral/key.pem
+	[ "$ssl" = "1" ] && procd_append_param command -s -c /etc/ucentral/operational.pem -k /etc/ucentral/key.pem
 	[ -n "$token" ] && procd_append_param command -t "$token"
 	[ "$verbose" = "1" ] && procd_append_param command -v
 	[ "$timeout" -eq "0" ] || procd_append_param command -e $timeout

feeds/ucentral/ucentral-schema/Makefile

@@ -4,10 +4,9 @@ PKG_NAME:=ucentral-schema
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-schema.git
-PKG_MIRROR_HASH:=45575f1f345368d109f74dc5ae3c8648dadbebef37e2d8eadc95b4fca2fbf43f
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_DATE:=2025-07-30
+PKG_SOURCE_DATE:=2025-08-04
-PKG_SOURCE_VERSION:=30c73745c104d56f58d4f457956fe7ebac6e0f86
+PKG_SOURCE_VERSION:=1c6b3095cb9e398fcbfcb2bf995365066eb76b21
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

patches/0096-base-files-boot-add-sync-after-uci-defaults.patch

@@ -0,0 +1,33 @@
+From 309a419087da906a2f3b0f39763f021e9729dd85 Mon Sep 17 00:00:00 2001
+From: Paul White <paul@shasta.cloud>
+Date: Mon, 4 Aug 2025 04:14:23 +0000
+Subject: [PATCH] base-files: boot: add sync after uci-defaults
+
+A scenario was seen where UCI config was not flushed to disk before
+an AP power-cycle after uci-defaults was completed.  Since these
+scripts are deleted after being ran once, there is no way to recover
+without a factory reset.
+
+Adding this sync operation proved to help avoid this situation from
+happening
+
+Signed-off-by: Paul White <paul@shasta.cloud>
+---
+ package/base-files/files/etc/init.d/boot | 1 +
+ 1 file changed, 1 insertion(+)
+
+diff --git a/package/base-files/files/etc/init.d/boot b/package/base-files/files/etc/init.d/boot
+index 15756669a9..c8a803e32c 100755
+--- a/package/base-files/files/etc/init.d/boot
++++ b/package/base-files/files/etc/init.d/boot
+@@ -15,6 +15,7 @@ uci_apply_defaults() {
+ 		( . "./$(basename $file)" ) && rm -f "$file"
+ 	done
+ 	uci commit
++	sync
+ }
+ 
+ boot() {
+-- 
+2.43.0
+

patches/0097-yuncore_ax820-add-insta1-2-partitions.patch

@@ -0,0 +1,36 @@
+From 3ceb72aaffa13375c049d161702e9d9f55da38c8 Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Mon, 4 Aug 2025 08:34:50 +0200
+Subject: [PATCH] yuncore_ax820: add insta1/2 partitions
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ target/linux/ramips/dts/mt7621_yuncore_ax820.dts | 12 +++++++++++-
+ 1 file changed, 11 insertions(+), 1 deletion(-)
+
+diff --git a/target/linux/ramips/dts/mt7621_yuncore_ax820.dts b/target/linux/ramips/dts/mt7621_yuncore_ax820.dts
+index b2f55b9be0..cc1b59340b 100644
+--- a/target/linux/ramips/dts/mt7621_yuncore_ax820.dts
++++ b/target/linux/ramips/dts/mt7621_yuncore_ax820.dts
+@@ -120,7 +120,17 @@
+ 			partition@90000 {
+ 				compatible = "denx,uimage";
+ 				label = "firmware";
+-				reg = <0x90000 0xf60000>;
++				reg = <0x90000 0xf40000>;
++			};
++
++			partition@fd0000 {
++				label = "insta1";
++				reg = <0xfd0000 0x10000>;
++			};
++
++			partition@fe0000 {
++				label = "insta2";
++				reg = <0xfe0000 0x10000>;
+ 			};
+ 
+ 			partition@ff0000 {
+-- 
+2.34.1
+

patches/0099-wireless-regdb-fix-channel-14-in-JP.patch

@@ -0,0 +1,39 @@
+From d0a0f0304f292a40f2fcdd20b320089627b0f05f Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Thu, 7 Aug 2025 14:50:51 +0200
+Subject: [PATCH] wireless-regdb: fix channel 14 in JP
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ .../patches/200-jp-no-channel-14.patch        | 19 +++++++++++++++++++
+ 1 file changed, 19 insertions(+)
+ create mode 100644 package/firmware/wireless-regdb/patches/200-jp-no-channel-14.patch
+
+diff --git a/package/firmware/wireless-regdb/patches/200-jp-no-channel-14.patch b/package/firmware/wireless-regdb/patches/200-jp-no-channel-14.patch
+new file mode 100644
+index 0000000000..ea1411cfdd
+--- /dev/null
++++ b/package/firmware/wireless-regdb/patches/200-jp-no-channel-14.patch
+@@ -0,0 +1,19 @@
++--- a/db.txt
+++++ b/db.txt
++@@ -16,8 +16,6 @@ country 00:
++ 	(2402 - 2472 @ 40), (20)
++ 	# Channel 12 - 13.
++ 	(2457 - 2482 @ 20), (20), NO-IR, AUTO-BW
++-	# Channel 14. Only JP enables this and for 802.11b only
++-	(2474 - 2494 @ 20), (20), NO-IR, NO-OFDM
++ 	# Channel 36 - 48
++ 	(5170 - 5250 @ 80), (20), AUTO-BW
++ 	# Channel 52 - 64
++@@ -945,7 +943,6 @@ country JO: DFS-JP
++ # https://www.soumu.go.jp/main_content/000833682.pdf
++ country JP: DFS-JP
++ 	(2402 - 2482 @ 40), (20)
++-	(2474 - 2494 @ 20), (20), NO-OFDM
++ 	(4910 - 4990 @ 40), (23)
++ 	(5170 - 5250 @ 80), (20), AUTO-BW
++ 	(5250 - 5330 @ 80), (20), DFS, AUTO-BW
+-- 
+2.34.1
+