mirror of
https://github.com/Telecominfraproject/wlan-ap.git
synced 2025-10-29 01:22:25 +00:00
f39339564a
1. porting MorseMicro HaLow driver to support HaLow on EAP112 2. Only support FCC regulation because of hardware limitation 3. Add /etc/init.d/halow-gpio-reset to initialize HaLow chip in early stage 4. Add /etc/uci-defaults/aaa-fix-phy0-to-morse to correct the default uci for HaLow radio. Signed-off-by: Ian Chen <ian77_chen@accton.com>
74 lines
2.4 KiB
Diff
74 lines
2.4 KiB
Diff
--- a/spi.c 2025-01-10 18:08:57.753837165 +0800
|
|
+++ b/spi.c 2025-01-13 14:17:01.746850459 +0800
|
|
@@ -1057,7 +1057,7 @@ static irqreturn_t morse_spi_irq_handler
|
|
struct morse *mors = spi_get_drvdata(mspi->spi);
|
|
|
|
MORSE_WARN_ON(FEATURE_ID_SPI, !mors);
|
|
- if (irq == gpio_to_irq(mors->cfg->mm_spi_irq_gpio)) {
|
|
+
|
|
/*
|
|
* If we are using edge interrupts, we need to continuously service the IRQ until
|
|
* either the chip has cleared all its IRQ bits, or the pin goes high again.
|
|
@@ -1067,8 +1067,7 @@ static irqreturn_t morse_spi_irq_handler
|
|
} while (spi_use_edge_irq && ret && !gpio_get_value(mors->cfg->mm_spi_irq_gpio));
|
|
|
|
return IRQ_HANDLED;
|
|
- }
|
|
- return IRQ_NONE;
|
|
+
|
|
}
|
|
|
|
static void morse_spi_enable_irq(struct morse_spi *mspi)
|
|
@@ -1311,10 +1310,15 @@ static int morse_spi_probe(struct spi_de
|
|
ret = morse_spi_cmd(mspi, SD_IO_MORSE_INIT, 0x00000000);
|
|
if (!ret)
|
|
break;
|
|
- pr_info("%s: SD_IO_RESET\n", __func__);
|
|
+ MORSE_DBG(mors, "%s: SD_IO_RESET\n", __func__);
|
|
morse_spi_cmd(mspi, SD_IO_RESET, 0x00000000);
|
|
}
|
|
|
|
+ if (ret) {
|
|
+ MORSE_SPI_ERR(mors, "failed initialise SPI: %d\n", ret);
|
|
+ goto err_cfg;
|
|
+ }
|
|
+
|
|
ret = morse_chip_cfg_detect_and_init(mors, mors_chip_series);
|
|
if (ret) {
|
|
MORSE_SPI_ERR(mors, "morse_chip_cfg_detect_and_init failed: %d\n", ret);
|
|
@@ -1327,7 +1331,11 @@ static int morse_spi_probe(struct spi_de
|
|
mors->cfg->mm_ps_gpios_supported = true;
|
|
ret = morse_spi_reg32_read(mors, MORSE_REG_CHIP_ID(mors), &mors->chip_id);
|
|
|
|
- if (!ret) {
|
|
+ if (ret) {
|
|
+ MORSE_SPI_ERR(mors, "failed to read chip id: %d\n", ret);
|
|
+ goto err_cfg;
|
|
+ }
|
|
+
|
|
/* Find out if the chip id matches our records */
|
|
if (!morse_hw_is_valid_chip_id(mors->chip_id, mors->cfg->valid_chip_ids)) {
|
|
MORSE_SPI_ERR(mors, "%s Morse chip (ChipId=0x%x) not supported\n",
|
|
@@ -1357,9 +1365,6 @@ static int morse_spi_probe(struct spi_de
|
|
mspi->inter_block_delay_bytes);
|
|
}
|
|
}
|
|
- } else {
|
|
- goto err_cfg;
|
|
- }
|
|
|
|
MORSE_SPI_INFO(mors, "Morse Micro SPI device found, chip ID=0x%04x\n", mors->chip_id);
|
|
MORSE_SPI_INFO(mors, "Board serial: %s\n", mors->board_serial);
|
|
@@ -1442,6 +1447,11 @@ static int morse_spi_probe(struct spi_de
|
|
#ifdef CONFIG_MORSE_ENABLE_TEST_MODES
|
|
if (test_mode == MORSE_CONFIG_TEST_MODE_BUS)
|
|
ret = morse_bus_test(mors, "SPI");
|
|
+
|
|
+ if (test_mode == MORSE_CONFIG_TEST_MODE_BUS_PROFILE) {
|
|
+ morse_bus_throughput_profiler(mors);
|
|
+ morse_spi_disable_irq(mspi);
|
|
+ }
|
|
#endif
|
|
|
|
return ret;
|