meowth: zoombini: Annotate ifdefs.

This commit just adds comments to the ifdefs introduced for
BOARD_ZOOMBINI.

BUG=None
BRANCH=None
TEST=make -j buildall

Change-Id: I036d18bc5b1fb4ebbf0943e630e4931c03b60aa5
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/772909
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>

board/zoombini/board.c

@@ -57,7 +57,7 @@ const enum gpio_signal hibernate_wake_pins[] = {
 };
 const int hibernate_wake_pins_used =  ARRAY_SIZE(hibernate_wake_pins);
 
-/* TODO(aaboagye): Add the additional Mewoth temps sensors */
+/* TODO(aaboagye): Add the additional Meowth temps sensors */
 const struct adc_t adc_channels[] = {
 	[ADC_TEMP_SENSOR_SOC] = {
 		"SOC", NPCX_ADC_CH0, ADC_MAX_VOLT, ADC_READ_MAX+1, 0
@@ -94,7 +94,7 @@ const struct power_signal_info power_signal_list[] = {
 	{GPIO_PMIC_DPWROK,    POWER_SIGNAL_ACTIVE_HIGH, "PMIC_DPWROK"},
 #ifdef BOARD_ZOOMBINI
 	{GPIO_PP5000_PGOOD,   POWER_SIGNAL_ACTIVE_HIGH, "PP5000_A_PGOOD"},
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 };
 BUILD_ASSERT(ARRAY_SIZE(power_signal_list) == POWER_SIGNAL_COUNT);
 
@@ -132,9 +132,7 @@ const unsigned int sn5s330_cnt = ARRAY_SIZE(sn5s330_chips);
 const int usb_port_enable[CONFIG_USB_PORT_POWER_SMART_PORT_COUNT] = {
 	GPIO_USB_A_5V_EN,
 };
-#endif
 
-#ifdef BOARD_ZOOMBINI
 /* Keyboard scan setting */
 struct keyboard_scan_config keyscan_config = {
 	/* Extra delay when KSO2 is tied to Cr50. */
@@ -149,7 +147,7 @@ struct keyboard_scan_config keyscan_config = {
 		0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca  /* full set */
 	},
 };
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 
 const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_COUNT] = {
 	{
@@ -173,7 +171,7 @@ const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_COUNT] = {
 		.drv = &tcpci_tcpm_drv,
 		.pol = TCPC_ALERT_ACTIVE_LOW,
 	},
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 };
 
 /* The port_addr members are PD port numbers, not I2C port numbers. */
@@ -196,7 +194,7 @@ struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_COUNT] = {
 		.driver = &tcpci_tcpm_usb_mux_driver,
 		.hpd_update = &ps8xxx_tcpc_update_hpd_status,
 	},
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 };
 
 static void board_chipset_startup(void)
@@ -204,7 +202,7 @@ static void board_chipset_startup(void)
 #ifdef BOARD_ZOOMBINI
 	/* Enable trackpad. */
 	gpio_set_level(GPIO_EN_PP3300_TRACKPAD, 1);
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 	/* TODO(aaboagye): Remove Trackpad function in P1 - moved to AP */
 }
 DECLARE_HOOK(HOOK_CHIPSET_STARTUP, board_chipset_startup, HOOK_PRIO_DEFAULT);
@@ -214,7 +212,7 @@ static void board_chipset_shutdown(void)
 #ifdef BOARD_ZOOMBINI
 	/* Disable trackpad. */
 	gpio_set_level(GPIO_EN_PP3300_TRACKPAD, 0);
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 	/* TODO(aaboagye): Remove Trackpad function in P1 - moved to AP */
 }
 DECLARE_HOOK(HOOK_CHIPSET_SHUTDOWN, board_chipset_shutdown, HOOK_PRIO_DEFAULT);
@@ -224,16 +222,14 @@ static void board_init(void)
 #ifdef BOARD_ZOOMBINI
 	struct charge_port_info chg;
 	int i;
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 
 	/* Enable TCPC interrupts. */
 	gpio_enable_interrupt(GPIO_USB_C0_PD_INT_L);
 	gpio_enable_interrupt(GPIO_USB_C1_PD_INT_L);
 #ifdef BOARD_ZOOMBINI
 	gpio_enable_interrupt(GPIO_USB_C2_PD_INT_L);
-#endif
 
-#ifdef BOARD_ZOOMBINI
 	/* Initialize VBUS suppliers. */
 	for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++) {
 		if (tcpm_get_vbus_level(i)) {
@@ -245,7 +241,7 @@ static void board_init(void)
 		}
 		charge_manager_update_charge(CHARGE_SUPPLIER_VBUS, i, &chg);
 	}
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 }
 DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);
 
@@ -320,7 +316,7 @@ int board_set_active_charge_port(int port)
 	gpio_set_level(GPIO_USB_C1_CHARGE_EN_L, port != 1);
 	gpio_set_level(GPIO_USB_C2_CHARGE_EN_L, port != 2);
 
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 	/*
 	 * TODO(aaboagye): Remove manual charge enabling on P1 -
 	 *  switched to sn5s330
@@ -366,7 +362,7 @@ uint16_t tcpc_get_alert_status(void)
 #ifdef BOARD_ZOOMBINI
 	if (!gpio_get_level(GPIO_USB_C2_PD_INT_L))
 		status |= PD_STATUS_TCPC_ALERT_2;
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 
 	return status;
 }

board/zoombini/board.h

@@ -38,7 +38,7 @@
 
 #ifdef BOARD_ZOOMBINI
 #define CONFIG_BC12_DETECT_BQ24392
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 #define CONFIG_CHARGER
 #define CONFIG_CHARGER_V2
 #define CONFIG_CHARGE_MANAGER
@@ -50,7 +50,7 @@
 #ifdef BOARD_ZOOMBINI
 #define CONFIG_CHARGE_RAMP_HW
 #define CONFIG_USB_CHARGER
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 
 #define CONFIG_CHIPSET_CANNONLAKE
 #define CONFIG_CHIPSET_RESET_HOOK
@@ -71,7 +71,7 @@
 #define CONFIG_KEYBOARD_PROTOCOL_8042
 #define CONFIG_PWM_KBLIGHT
 #define CONFIG_SWITCH
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 
 #define CONFIG_USB_POWER_DELIVERY
 #define CONFIG_USB_PD_ALT_MODE
@@ -80,7 +80,7 @@
 #define CONFIG_USB_PD_PORT_COUNT 3
 #else
 #define CONFIG_USB_PD_PORT_COUNT 2
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 #define CONFIG_USB_PD_DUAL_ROLE
 #define CONFIG_USB_PD_LOGGING
 /* TODO(aaboagye): What about CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT? */
@@ -100,7 +100,7 @@
 #define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1
 #define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY
 #define GPIO_USB1_ILIM_SEL GPIO_USB_A_HIGH_POWER_EN
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 
 /* Define typical operating power and max power. */
 #define PD_MAX_VOLTAGE_MV 20000
@@ -148,7 +148,7 @@
 #define GPIO_TCPC0_SDA GPIO_I2C5_SDA
 #define GPIO_TCPC1_SCL GPIO_I2C1_SCL
 #define GPIO_TCPC1_SDA GPIO_I2C1_SDA
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 
 #define PMIC_I2C_ADDR TPS650X30_I2C_ADDR1
 
@@ -157,7 +157,7 @@
 #else
 #define PP5000_PGOOD_POWER_SIGNAL_MASK \
 POWER_SIGNAL_MASK(PP5000_PGOOD)
-#endif
+#endif /* defined(BOARD_MEOWTH) */
 
 #ifndef __ASSEMBLER__
 
@@ -188,7 +188,7 @@ enum power_signal {
 	X86_PMIC_DPWROK,
 #ifdef BOARD_ZOOMBINI
 	PP5000_PGOOD,
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 	POWER_SIGNAL_COUNT
 };
 

board/zoombini/ec.tasklist

@@ -48,4 +48,4 @@
 	TASK_ALWAYS(POWERBTN, power_button_task, NULL, LARGER_TASK_STACK_SIZE) \
 	TASK_ALWAYS(PD_C0, pd_task, NULL, LARGER_TASK_STACK_SIZE) \
 	TASK_ALWAYS(PD_C1, pd_task, NULL, LARGER_TASK_STACK_SIZE)
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */

board/zoombini/gpio.inc

@@ -217,4 +217,4 @@ ALTERNATE(PIN_MASK(F, 0x02), 1, MODULE_ADC, 0) /* ADC8 */
 ALTERNATE(PIN_MASK(0, 0x03), 1, MODULE_PMU, 0) /* GPIO00, GPIO01 */
 ALTERNATE(PIN_MASK(D, 0x04), 1, MODULE_PMU, 0) /* GPIOD2 */
 
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */

board/zoombini/usb_pd_policy.c

@@ -124,7 +124,7 @@ void pd_power_supply_reset(int port)
 	};
 #else
 	/*TODO(aaboagye): Implement sn5s330 PPC for both Zoombini and Meowth */
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 
 	/* Notify host of power info change. */
 	pd_send_host_event(PD_EVENT_POWER_CHANGE);
@@ -166,7 +166,7 @@ int pd_set_power_supply_ready(int port)
 	};
 #else
 	/*TODO(aaboagye): Implement sn5s330 PPC for both Zoombini and Meowth */
-#endif
+#endif /* defined(BOARD_ZOOMBINI) */
 
 	/* Notify host of power info change. */
 	pd_send_host_event(PD_EVENT_POWER_CHANGE);