Early hardware bringup often is complicated by exceptions happening in
the code all over the place. Using interrupt based console output to
trace startup progress is inefficient - a lot of text gets buffered
and never shows up on the console.
The new config option enables the mode where the console output is
supposed to be happening in polling mode, the character transmit
function not exiting until the entire character is transmitted.
BRANCH=none
BUG=chrome-os-partner:43791
TEST=with the new config enabled (and the appropriate changes to
chip/g/uart.c) was able to debug bringup on the new version.
Change-Id: I85fd2f3990ac1d31097d58bd6a7fa658b2b5146e
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/291852
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
The motion sense task was checking to see that every single motion
sensor was ready (active, initialized, and reading), before performing
the lid angle calculations. This amount of checking is unnecessary.
This commit reduces the condition to only check if the sensors required
for lid angle calculation are ready.
BUG=chrome-os-partner:36132
BRANCH=None
TEST=Build and flash on samus. Verify that the lid still works.
TEST=make -j buildall tests
Change-Id: Ibaa5cc8358cdcc6023a50aed247fce2e599fef58
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/291301
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Move common USB charger code out of board directory including
setting VBUS supplier when VBUS changes, and initializing BC1.2
supplier types on init.
This also enables re-enabling of Pericom BC1.2 detection interrupts
when VBUS is changed on all boards that use USB_CHG task.
BUG=chrome-os-partner:42292
BRANCH=none
TEST=make -j buildall. Tested on glados and samus by plugging in
a few different chargers and making sure we charge.
Change-Id: Ib102fbf7a6aace998e6fcb6d35f3c97e5f03f5c2
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/290453
Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Rong Chang <rongchang@chromium.org>
Fix buffer overrun bug when retrieving a PD message. Bug was
introduced in CL:289005
BUG=chrome-os-partner:43482
BRANCH=none
TEST=tested on samus. plug and unplug zinger on both ports and
make sure PD MCU never crashes.
Change-Id: I9d2dec0cab07f389fd935d616ab7443da412d4bd
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/290417
Reviewed-by: Shawn N <shawnn@chromium.org>
Don't enable try.src when battery is not present or <1% because
try.src will temporarily cut off power to system.
BUG=chrome-os-partner:43413
BRANCH=samus
TEST=tested on samus using "battfake" ec command. when battery
<1%, verified that try.src is disabled and when battery >=1% and
the AP is on (dual-role toggling is on), then try.src is enabled.
verified boot without battery succeeds on samus and glados.
Change-Id: I64816bb7c9669bfeca61687bcd9a48da32e67945
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/289854
Reviewed-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add RX message buffer to the TCPC (currently two deep). If
the buffer is full and message is received, don't send goodCRC.
BUG=chrome-os-partner:43482
BRANCH=none
TEST=tested on glados. saw that with back to back PD
packets, we send goodCRC to both packets and process them in
order, taking about 7ms per packet. also tested buffer size
of 1 and verified that with back to back PD packets, we don't
send goodCRC to second packet.
Change-Id: I7f44b3c3a186ae61be8ca03017deec6e6b6c6f9f
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/289005
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This patch implements FIFO mode state machine transitions as described
in Table 22 of the PC Client Platform document.
The 'go' command is still not being handled, as processing needs to
run on a task, not on interrupt context. FIFO block integrity is
somewhat verified by comparing the actual block size to the length
value in the block body.
BRANCH=None
BUG=chrome-os-partner:43025
TEST=not much. Observed trunksd happily initializing the session and
sending the Startup command. The target reports:
fifo_reg_write: received fifo command 0x0144
Change-Id: I76d8b0fc3a52db2cc487c781fe92799df0ee259e
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/288365
Reviewed-by: Utkarsh Sanghi <usanghi@chromium.org>
When LPC mode is used, there is an assumption that the first
2 sensors are accelerometers, and the optional 3rd is a gyro.
Put the code that fill lpc_data with #ifdef.
Prevent lpc space corruption if more than 3 sensors are present.
BRANCH=smaug
TEST=Compile. Smaug works
BUG=None
Change-Id: I12c9b823efb57d7b190a1813228f6f02fa0bebcb
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/290073
We need to call irq_handler and load_fifo even if the
first sensor is disable. Nothing is done on otherwise.
Move code to recalculate sample rate to the right place.
BRANCH=smaug
TEST=Check data is collected when accel is disabled.
BUG=chrome-os-partner:39900
Change-Id: Ia6025a670abaf2e71ccbe784bce24e08becf399e
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/289838
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Allow more than one SPI master.
Add CONFIG variables to address the system SPI flash.
To have SPI master ports, spi_ports array must be defined.
BRANCH=smaug
TEST=compile
BUG=chrome-os-partner:42304
Change-Id: Id43869f648965c1582b7be1c7fb3a38f175fda95
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/288512
Commit-Queue: David James <davidjames@chromium.org>
Modify host_command_pd.c to loop over sending of PD status
host command and processing the response as long as the
alert GPIO is active.
This fixes a potential bug that if the alert line is held
low for more than one PD status host command, then we would
not process the return status.
Also, fix a bug in which we could call alert() for a
non-existent port.
BUG=none
BRANCH=strago
TEST=verified on samus and glados. connected charger and verified
that we negotiate a contract and set appropriate input currnet limit.
Change-Id: I3b2db87b51f55fc2b20a4695bd466ff8bb09ea55
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/288819
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Trybot-Ready: David James <davidjames@chromium.org>
For multi-byte ACPI memmap reads, we previously had a mutex to ensure
data continuity. A better approach is to use a read cache. Since the
kernel will enable burst mode before reading a multi-byte memmap
variable and disable it afterward, we can populate the cache on the
first read after enabling burst. This solution removes deadlock bugs, is
contained entirely in acpi.c, and saves a deferred function.
BUG=chromium:514283
TEST=Manual on Glados. Add prints in acpi_read, verify that multi-byte
reads come from cache and non-burst reads continue to function as
before.
BRANCH=Cyan
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I74e4927bf2b433e31a9ff65d72820fa087c51722
Reviewed-on: https://chromium-review.googlesource.com/288871
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
active state is global, remove it from motion_sensor structure.
Reinit sensors when entering RW, fix regression introduced by CL:284616.
Improve EC polling rate calculation by excluding suspended sensors.
Wake up sensor thread in case the motion task was in deep sleep.
Do not send sense interrupt while suspened. Will revisit once wakeup
sensors are implemented.
BRANCH=smaug
TEST=Check when in RW the sensors are exposed.
Check EC rate are correct in different power state.
Check when jumping from RO to RW and back, after setting the
frequencies parameters via sysfs properly, AndroSensor acquires
the data properly.
BUG=chrome-os-partner:43132,chrome-os-partner:40741
Change-Id: Ie70732b135a432d64935eead4200ddc0e1a7c0b4
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/288201
Reviewed-by: Alec Berg <alecaberg@chromium.org>
After I2C unwedge, *all* I2C ports will be re-initialized in
i2c_raw_mode() by gpio_config_module(MODULE_I2C, 1);
This means *all* I2C pins will be programmed as GPIO then enable I2C
alternate function.
If I2C Unwedge happened while there is an active I2C transacation on
another port, the active I2C transaction will be corrupted, since the
pins will be temporary programmed as GPIO Output High.
BUG=chrome-os-partner:40519
TEST=Warm-reboot test on Cyan EVT and no discharging while AC is on.
BRANCH=none
Change-Id: I3be1d5c60bf4ab385bc077202406ec7abd8b2add
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/287493
Reviewed-by: Shawn N <shawnn@chromium.org>
Commit-Queue: Denny Iriawan <denny.iriawan@intel.com>
This patch adds a module which runs on top of the SPS driver and
implements the TCG SPI TPM protocol.
Basic register read and write functions are implemented as well as
rudimentary TPM state machine (claiming/releasing locality).
An enhancement is made to the SPS driver to ensure that when the CS is
deasserted the transmit FIFO is reset too, on the off chance of the CS
going away mid transaction for whatever reason.
In this implementation the slave is guaranteed to stall the master for
a few bytes in both receive and transmit transactions, which is
further aggravated by the fact that RX FIFO threshold is set to 8
(this is the minimum number of bytes the master has to send to wake up
the slave). This could be fine tuned later, for instance made a
parameter of the receive callback registration function.
BRANCH=none
BUG=chrome-os-partner:43025
TEST=trunksd initialization (with minor changes to accommodate new
VID/DID and some status bits, to be published) succeeds with the
cr50 connected to the USB/SPI cable.
Change-Id: I28d37c3b57dde9adf59e81426efe4f58880cf0b0
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/285252
As new features come along the console channel space limited at 32
becomes very tight. But not all features are present all the time.
Let's make some of the channels compile time configurable. This makes
for uglier code but allows to support more channels.
BRANCH=none
BUG=none
TEST=make buildall -j
Change-Id: Id21560d4aa05c0e5245872c50ae19340cda8fd3e
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/286610
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
SPI slave and master interfaces require very different code to
support, they should have separate configuration options.
Host command code printouts should use their own console channel.
Using SPS to designate SPI Slave interface is not universally
acceptable, a bug has been opened to discuss the alternatives and
clean up the code.
BRANCH=none
BUG=chromium:512613
TEST=make buildall -j
Change-Id: I6683286a221c4689ecc247fdfe8ebca529f3f458
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/286469
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Move TCPC initialized bit from alert register into error status
register. This is not part of the TCPCI spec, but the existing
code creates a bug that if TCPM reboots without TCPC also rebooting,
then we will never get the initialized alert from TCPC since
it has already happened, so the TCPM will loop indefinitely
waiting for TCPC to be ready. This fixes the bug by moving the
bit to a status register, which is more appropriate.
BUG=none
BRANCH=none
TEST=load on glados, reboot and make sure TCPM see's that the
TCPC is initialized.
Change-Id: I8e96b59031e01a4faec8f519727df1fa95f498bc
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/288342
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add a X-macro CONFIG_LID_SWITCH_GPIO_LIST to be able to optionally
specify more than one GPIO to check to find out whether the lid is open.
By default, use GPIO_LID_OPEN as before.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=smaug
BUG=chrome-os-partner:42110
TEST=on Smaug EVT2, define CONFIG_LID_SWITCH_GPIO_LIST as
LID_GPIO(GPIO_LID_OPEN) LID_GPIO(GPIO_BASE_PRES_L) and play with magnets
and the genuine lid, check we get the right "lid open" / "lid close"
messages on the console.
Change-Id: I9e7c67bb39f36f254d31d5861d535d69db754faa
Reviewed-on: https://chromium-review.googlesource.com/287852
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
It's sometimes desirable to boot without a battery, but we may brown out
if we don't have sufficient current. Inhibit AP power-on, even if the system
is unprotected, until our charger and current limit are initialized.
BUG=chrome-os-partner:41258
TEST=Manual on reworked glados with subsequent commit. Remove battery and
attach Zinger. Verify EC powers on and AP doesn't boot. Run `powerbtn`,
verify that AP boots. Remove all power and attach battery, verify that EC
powers on and AP boots.
BRANCH=None
Change-Id: Ifc3d16f8288a035854e9fd05812ce6de33170d6a
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/280563
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Add matrices to align sensors vectors with the device reference.
Move rotation in read routines, to allow fifo to contains processed
information.
BRANCH=smaug
TEST=Worsk on smaug
BUG=chrome-os-partner:39900
Change-Id: I009e7f24ef6ee0574ed664aeb5fd649fcd7039fd
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/286659
Reviewed-by: Alec Berg <alecaberg@chromium.org>
math library can be set independentely.
It is implied when motion sensor drivers are compiled in.
BRANCH=smaug
TEST=Build strago board specific tests, host test and ran
ryu image.
BUG=chromium:512329
Change-Id: I743ea7b44e4a3783602c11f3928cb3fa4b105ec4
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/287371
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Make the PD port state string more friendly with console limited to
64-byte wide string (eg current USB console).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=on Smaug, open the USB-console to the EC and type "pd 0 state" and
see the current type-C port state string.
Change-Id: I6903fd0f0b7371aef978f696370a6e3a200c7fa5
Reviewed-on: https://chromium-review.googlesource.com/286785
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
This commit adds the 8042 scancodes to the shared objects library saving
504 bytes from the RW image. To enable the space savings, define
CONFIG_SHAREDLIB in the target's board.h file.
BUG=none
BRANCH=none
TEST=make -j buildall tests
TEST=Built samus EC image and verified keyboard still worked in RO and
RW.
TEST=Built samus EC image with CONFIG_SHAREDLIB enabled and verified
that the keyboard still worked in RO and RW.
TEST=Enabled CONFIG_SHAREDLIB for glados and cyan and watched build
fail.
CQ-DEPEND=CL:275344
Change-Id: I1241506c6b34d63e270677d4e8d0531a8a4236c9
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/276212
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Commit-Queue: Aseda Aboagye <aaboagye@chromium.org>
This commit introduces the build infrastructure changes needed for
creating a shared RO library. (libsharedobjs). The end goal is for the
library to contain various objects that can be shared with both the RO
and RW EC images.
Now, there are 3 make goals: ro, rw, and libsharedobjs.
In order for changes that are only specific to a single image (ie: RW
only) to be applied correctly, the object files are now built separately
for the RO, RW, shared objects library targets.
NOTE: Certain EC targets are incompatible with this model due to the
fact that only one image is present within flash at a time.
BRANCH=none
BUG=None
TEST=make -j buildall tests
TEST=make -j BOARD=cr50 xrefs
TEST=make BOARD=samus dis
TEST=Built samus EC image and compared that the final EC image was
identical to the upstream version (except for the git SHAs & version
strings).
CQ-DEPEND=CL:285934
Change-Id: I8e67f089710be9c6d7017718109262394bdad2f5
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/274079
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Commit-Queue: Aseda Aboagye <aaboagye@chromium.org>
* Fixes cyan/board.h to use correct SPI part
* Adds new flash protection regions in spi_flash_reg.c
* Sets SRP register in flash_physical_protect_at_boot()
* Fixes a bug in COMPARE_BIT macro
* Makes spi_flash_set_status() fail only when both HW pin is asserted
AND SRP(s) are set
* Makes sure set_flash_set_status() completes before returning
BUG=chrome-os-partner:40908
BRANCH=master
TEST=on Cyan:
With WP pin de-asserted:
flashrom -p ec --wp-enable
flashrom -p ec --wp-status, make sure it is enabled
flashrom -p ec --wp-disable
flashrom -p ec --status, make sure it is disabled
flashrom -p ec --wp-enable
Assert WP pin (either with screwdriver or dut-control)
flashrom -p ec --wp-disable
make sure it failed
Change-Id: I338cc906b73e723fdbb37f7c2fd0c4da358b6c8e
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/276671
Reviewed-by: Shawn N <shawnn@chromium.org>
Tested-by: Divya Jyothi <divya.jyothi@intel.com>
Commit-Queue: Divya Jyothi <divya.jyothi@intel.com>
To ease driver loading in the kernel, add a bit in the feature field
to indicate the EC has an internal software FIFO for sensor events.
BRANCH=smaug
BUG=chrome-os-partner:39900
TEST=compile, kernel modules load as expected on Smaug.
Change-Id: I1ae0b9ebb587bb4939745e8a0e16d73d95ba31d7
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/285774
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Previously all access to the queue was done by adding or removing units
with no access to the underlying byte array, or ability to notify the
queue that the byte array had been updated. This prevented direct DMA
transfers to and from the underlying byte array.
This change adds a new struct, a queue_chunk, that represents a
contiguous region of the queues byte array. Regions of valid units as
well as free space can be requested. And there are now update functions
to signal to the queue that new units were added or existing units were
read from these chunks. A chunk can be queried and used to initialize
a DMA transfer, as interrupts or polling indicates that the DMA is
working the queue indicies can be updated and the policy activated as
needed.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Change-Id: I7e37d937c56153122f0a3c73ba8064b656106e3a
Reviewed-on: https://chromium-review.googlesource.com/285556
Trybot-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Even a decent type-C device SHALL respond SNK_CAP query message when we are in
SRC_READY state, but in the case its mal implementation shouldn't get us being
trapped in an infinite loop of SRC_READY / SRC_GET_SNK_CAP states.
Introduce a counter to give up sending of SNK_CAP and just print a ERR
indication log when the partner device ignores SNK_CAP query.
BUG=none
BRANCH=samus
TEST=make buildall
manual testing against the failing USB-C device
Change-Id: I4c4251b2264230d7dd30bd2b9fc2b56027ff0d5a
Signed-off-by: Bernard Shyu <bernard_shyu@bizlinktech.com>
Reviewed-on: https://chromium-review.googlesource.com/284035
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Alec Berg <alecaberg@chromium.org>
- Compass was not set properly if default config is set to
disable it (frequency == 0). We were trying to set it up
while stuck in debug mode.
- BMI150 FIFO collects sensor info even when suspended.
Ask FIFO to ommit suspended sensors.
- FIx compliation issue on nucleo-f411 board, where
MKBP is not enabled.
- Fix location of __packed arguement.
BRANCH=smaug
BUG=none
TEST=Check the compass is back with accelinfo,
FIFO is not filled with garbage with fiforead.
Check by echoing in in_accel_z_calibbias that the format
of MOTIONSENSE_CMD_SENSOR_OFFSET has not changed.
Change-Id: I7ebec12a14a74b8385b9f9532562a1fd0213f4d7
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/284929
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Add code for set/getting calibration data on bmi160
Add code to perform FOC (Fast Online Calibration) on bmi160.
Add delay after getting out of suspend to be sure sensor is
available.
BRANCH=smaug
TEST=Check sensors are properly calibrated on Smaug:
Perform calibration:
echo 1 > /sys/bus/iio/devices/iio:device1/calibrate
Read calibration values:
cat /sys/bus/iio/devices/iio:device1/*_calibbias
Check the values are translated properly.
Write calibration values and check it affects the
sensor output.
BUG=chromium:506101,chrome-os-partner:39900
Change-Id: Ib9aad9bbd90b4249625641d68febf94b69aa4987
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/283165
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Store at which frequency each sensor should be sampled.
This frequency is different from the sensor frequency:
- sensor frequency: frequency at which the sensor produce information.
- sensor sampling frequency: frequency at the which the EC gater
information.
If 2 sensors must be sampled at very different frequency,
we don't want to oversample the slow one, and filling the
software FIFO unnecessarily.
BRANCH=smaug
TEST=Unit test. Check that frequency is correct when sensor
frequencies change from IIO driver.
BUG=chrome-os-partner:39900
Change-Id: I4272963413f53d4ca004e26639dc7a2affd317eb
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/284616
Reviewed-by: Alec Berg <alecaberg@chromium.org>
port80 task polling prevents the EC from entering low power states and
isn't useful when the AP isn't running. Therefore, when
CONFIG_PORT80_TASK_EN is enabled, only enable the port80 task when
entering S0, and disable it when leaving S0.
BUG=chrome-os-partner:42104
TEST=Manual on Glados. Boot AP, verify that 'port80' log starts with "10
20...". Shutdown AP, verify with 'taskinfo' that PORT80 task stops
consuming cycles. Boot AP again, verify that 'port80' log starts with
new "10 20...".
BRANCH=None
Change-Id: Id41dbdaa4597456d042b7a3921c1ec439af759f4
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/285550
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
When FIFO overfills, keep track of the number of lost vectors per
vector types. This way, when we calculate timestamps in user space,
we can evaluate the number of empty slots to skip per vector type.
This is important when different types are samples at very different
frequencies.
BRANCH=smaug
TEST=Check that when we drop events, the timestamp are better than
without.
BUG=chrome-os-partner:39900
Change-Id: Ib9cb994ada38373e5a49dd4ba2123ca7534a169e
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/284615
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Remove duplicate board_discharge_on_ac() functions and create
CONFIG_CHARGER_DISCHARGE_ON_AC_CUSTOM for boards that have a
unique implementation of board_discharge_on_ac().
BUG=chrome-os-partner:42294
BRANCH=none
TEST=make -j buildall.
load on samus and test 'ectool chargecontrol discharge' forces
discharging on AC, and 'ectool chargecontrol normal' resumes normal
charging.
Change-Id: I2b7c04b9278d07748d6d41798ceab1a7e90684e4
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/284911
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This commit changes the way in which tasks are started. Instead of
having all tasks marked as ready to run upon initialization, only the
hooks task is marked as ready to run. HOOK_INITs are now run at the
beginning of the hooks task. After the HOOK_INITs, the hooks task calls
back to enable the rest of the tasks, reschedules, and proceeds as
usual. This also allows the removal of checks for task_start_called().
BUG=chrome-os-partner:27226
BRANCH=None
TEST=Built and flash EC image for samus and verified that EC boot was
successful as well as AP boot. Additionally, verified that charging,
keyboard, tap-for-battery were all still functional.
TEST=make -j buildall tests
Change-Id: Iea53670222c803c2985e9c86c96974386888a4fe
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/283657
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Remove board function callback on charge override timeout, since
the implementation should be common to all boards: send host event.
This function is called when a power swap fails during an issued
charge override and notifies the host so that it is aware that the
power swap did not succeed.
BUG=none
BRANCH=smaug
TEST=make -j buildall
Change-Id: Ia2a078a17aef6b302fd2b9fd21a5a92c628fd7db
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/284923
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Remove duplicate definitions of USB charger min current across
boards and make one set of defines for standard USB charger voltage
and minimum USB charger current.
BUG=none
BRANCH=smaug
TEST=make -j buildall
Change-Id: Ib842fafb317417c8de9a67d314fdde4c1e47ad9d
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/284956
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add FIFO support, where bmi160 hardware FIFO is copied in local fifo.
Add rudimentary support for single/double tap and lift detection.
BUG=chrome-os-partner:39900
BRANCH=smaug
TEST=Check on F411 that FIFO data is retrieved and correct.
Check on Smaug as well, with proper kernel the collect the FIFO:
- check that increasing sampling_frequency we are collecting
the FIFO less often
- check no frames are lost.
- check tap/lift interrupts are working
- if latency is less than 100ms, check we are collecting much faster.
Change-Id: Ic2317c27fad0ef31dacd6e18cd5f71ccd2cec807
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/274227
Move calibration in the EC to returns raw value with offset already
applied, as recommended by iio interface.
BRANCH=smaug
TEST=On Samus, with kernel change CL:283103
Check raw value are returned properly.
BUG=chromium:506101
Change-Id: I3dcb4f2fcfff35639e3bfdcc6c1468bdb5e53c45
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/283161
Reviewed-by: Alec Berg <alecaberg@chromium.org>
1. Added new config option CONFIG_USB_PD_TRY_SRC
2. Added pd_try_source_enable global flag with console command
3. Added bit to pd.flags to indicate Try.SRC states are active
BUG=chrome-os-partner:39724
TEST=Manual samus to samus with the Try.SRC enabled on both and just
one samus. Tested Samus to Honeybuns and Samus to Zinger connections.
BRANCH=TOT
Change-Id: Ifa5d5d82e443f376e546aaf852ff24d92ef04d72
Signed-off-by: Scott Collyer <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/282052
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Tested-by: Alec Berg <alecaberg@chromium.org>
1. Add flash control module for emulation board.
2. Fix system jump for Andes core.
3. Change the physical size of the flash on the chip to 256KB.
note:
1. Only IT839x series supports flash write protect by registers.
2. Static DMA method of flash code only for IT839x series and IT838x Dx.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. console command flashwp and flashinfo
1-a. flashwp enable
1-b. WP asserted and reboot
1-c. flashinfo RO protected now
1-d. WP deasserted and reboot
1-e. No protected
1-f. flashwp disable
1-g. WP asserted and reboot
1-h. No protected
2. console sysjump and sysinfo
2-a. sysjump rw
2-b. jumping to image RW
2-c. sysinfo, Copy : RW, Jumped : yes
2-d. sysjump ro
2-e. jumping to image RO
2-f. sysinfo, Copy : RO, Jumped : yes
3. RO/RW firmware image test
3-a. sysjump rw
3-b. use console command "eflash" to erase RO region,
erase OK and system still work.
3-c. reflash firmware
3-d. sysjump rw, sysjump ro
3-e. use console command "eflash" to erase RW region,
erase OK and system still work.
Change-Id: I7666a095e73026a02fb812e5143bc5172ab713e8
Reviewed-on: https://chromium-review.googlesource.com/271390
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
"RO" is a workaround for GP base instructions.
And now we have added "-mno-gp-direct" option in the NDS32 toolchain.
So the compiler would not generate GP base instructions directly,
and we can remove this "RO".
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=chrome-os-partner:24378
TEST=console "version" and "gpioget"
Change-Id: I23cb6374fb8eb57081d713bf5c70b80a87dd2fb5
Signed-off-by: Dino Li <dino.li@ite.com.tw>
Reviewed-on: https://chromium-review.googlesource.com/281862
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
DP Alternate mode specification defines two bytes in the DP
capabilities payload with respect to pin configs. One that governs
the DFP and the other the UFP. The one that the DP source needs to
examine depends upon whether the UFP is a receptacle or a plug.
Previously we just examined the DFP pin config which was correct for
all UFP plugs but not UFP receptacles. This change fixes that by
examining bit <6> of capability message to determe plug vs receptacle
and in case of receptacle choosing the UFP ping config instead.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BRANCH=samus
BUG=chromium:505652
TEST=manual, hoho & apple (UFP_D plugs) still work.
While I don't have a test for UFP_D receptacle partner device reports
following for its DP caps which should now decode correctly.
<31:24> 00 Reserved/SBZ
<23:16> 1C UFP pin config == C, D, E
<15:08> 00 DFP pin config zero
<07:00> C5 <6> == 1 == receptacle
Change-Id: Ib9e3a808828ff6b8c062baf0fc3c23b3da33c2c3
Reviewed-on: https://chromium-review.googlesource.com/282621
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
If flash is being written, any pending hash calculation is likely to
be invalid.
BRANCH=None
BUG=chrome-os-partner:38103
TEST=on Cyan, run hundreds of flashrom cycles to make sure there are no
read, erase or write errors
Change-Id: I915f8db7998c56fc12e7d85173232882fb7ed80d
Signed-off-by: Divya Jyothi <divya.jyothi@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/282211
Reviewed-by: Shawn N <shawnn@chromium.org>
Commit-Queue: Bernie Thompson <bhthompson@chromium.org>
Tested-by: Bernie Thompson <bhthompson@chromium.org>
When the USB2.0 port is used in device mode, having the D+/D- lines
connected just before resetting the PI3USB9281 (for the 2nd detection
used a BC1.2 debouncing) triggers a misdetection where DCP chargers are
seen as Apple 2.4A chargers.
To avoid this, disconnect the D+/D- lines and let them relax before
triggering the PI3USB9281 reset.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=smaug
BUG=chrome-os-partner:42048
TEST=connect and disconnect a DCP charger to the Smaug type-C port
with the AP running, see it constantly detected as DCP and no Pericom
interrupt storm.
Change-Id: I8f6043439c2c6b52f2689b4947baffe51f62eba8
Reviewed-on: https://chromium-review.googlesource.com/282594
Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Take profit of the hardware input current ramping/back-off integrated
in the BQ2589x charger by setting the current limits higher for BC1.2
USB modes and letting the hardware adjust to the actual charger
limitation depending on the VBUS voltage droop.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=smaug
BUG=chrome-os-partner:42045
TEST=Connect a Nexus 9 DCP charger to Smaug and see the input current
adjusted to 1650mA without brown-out, read back the value properly from
the AP:
$ ectool usbpdpower
Port 0: SNK Charger DCP 4958mV / 1650mA, max 5000mV / 1650mA / 8250mW
Change-Id: I348e5ee4980a5652f72f279ab4e3a7126583b093
Reviewed-on: https://chromium-review.googlesource.com/282584
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
