When (USB-)resuming from deep-sleep, ensure that we avoid switching back
and forth the selected USB PHY at boot, in order to avoid having a
short disconnection at resume.
To achieve this, allow the board configuration to select the PHY it is
really using with the CONFIG_USB_SELECT_PHY_DEFAULT configuration
variable, still keep the default USB_SEL_PHY1 as before.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:38160821
TEST=manual: build 'proto2' firmware with CONFIG_LOW_POWER_IDLE defined,
with the chip connected to the host on PHY A, make the host issue a USB
Suspend then resume and see no disconnection.
Change-Id: I7abd5e338e5c688c2dd486293f520049cdfd273b
Reviewed-on: https://chromium-review.googlesource.com/501947
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Marius Schilder <mschilder@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
This patch adds a dedicated charge port. The number of such ports
is specified by CONFIG_DEDICATED_CHARGE_PORT_COUNT. It works as a
sink only. The total number of charge ports is represented by
CHARGE_PORT_COUNT.
BUG=chromium:721383
BRANCH=none
TEST=make buildall. Boot Fizz off of barrel jack.
Change-Id: Ibbb11f3e1c66e35b5abe190e49161eeaa2009994
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/501468
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This CL implements two methods for hibernating on npcx7 ec. One is using
PSL (Power Switch Logic) circuit to cut off ec's VCC power rail. The
other is turning off the power of all ram blocks except the last code
ram block. In order to make sure hibernate utilities are located in the
last code ram block and work properly, we introduce a new section called
'after_init' in ec.lds.S.
We also moved the hibernate utilities, workarounds for sysjump and so on
which are related to chip family into system-npcx5/7.c. It should be
easier to maintain.
It also includes:
1. Add CONFIG_HIBERNATE_PSL to select which method is used on npcx7 for
hibernating.
2. Add new flag GPIO_HIB_WAKE_HIGH to configure the active priority of
wake-up inputs during hibernating.
3. Add DEVICE_ID for npcx796f.
BRANCH=none
BUG=none
TEST=No build errors for all boards using npcx5 series.
Build poppy board and upload FW to platform. No issues found. Make
sure AC_PRESENT and POWER_BUTTON_L can wake up system from
hibernate. Passed hibernate tests no matter CONFIG_HIBERNATE_PSL is
enabled or not on npcx796f evb.
Change-Id: I4e045ebce4120b6fabaa582ed2ec31b5335dfdc3
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/493006
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This patch declares recovery_buttons array, where each board
lists recovery buttons. Pressing those while the board reboots
makes the system enter recovery mode.
BUG=none
BRANCH=none
TEST=buildall
Change-Id: I1f204156efbd6d2a507d67ba90f75ce857b03559
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/486944
On some boards, the boot key combinations do not make a lot of
sense, so we can just not process them and save a little bit
of code space.
BRANCH=none
BUG=b:37422577
TEST=Flash hammer
TEST=make newsizes shows we save 156 bytes in hammer RW.
Change-Id: Ic96d7ed1dbee10f44f8b08568ab70b2f20961842
Reviewed-on: https://chromium-review.googlesource.com/495968
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
On some boards, the special alt-volup-r/h combinations do not make
a lot of sense, so we can just not process them and save a little
bit of code space.
BRANCH=none
BUG=b:37422577
TEST=Flash hammer, alt-volup-r/h does not do anything special
TEST=make newsizes shows we save 124 bytes in hammer RW.
Change-Id: I92770fd6b8ff90780162a6b1de428a550bb44e9b
Reviewed-on: https://chromium-review.googlesource.com/495967
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The cros_ec_debugfs creates the `console_log` debugfs entry if EC
supports EC_CMD_CONSOLE_READ version 1. On device where i2c command
latency is critical, periodic console_read is impacting the timing of
commands.
BRANCH=none
BUG=b:37584134
TEST=on rose with CONFIG_CONSOLE_ENABLE_READ_V1 undefined, the kernel
should not create cros_tp/console_log.
Change-Id: I40d0b959ef36f2f410155fa30e01c8169032a3e9
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://chromium-review.googlesource.com/494546
Commit-Ready: Wei-Ning Huang <wnhuang@chromium.org>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
This CL added the support for the quasi-bidirectional buffer which has
an open-drain output and a low-impedance pull-up resistance on KSO pins.
The low-impedance pull-up is active when ec changes the output data
buffers from 0 to 1, thereby reducing the low-to-high transition time.
Add CONFIG_KEYBOARD_KSO_HIGH_DRIVE to enable/disable this feature for
npcx7 series ec.
BRANCH=none
BUG=none
TEST=No build errors for all boards using npcx5 series.
Build poppy board and upload FW to platform. No issues found.
Change-Id: I138f0e433394816e1e5c58b5053580f202c1ac48
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/497189
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Create an app to extract relevant information
from the EC code base that's used to create Vendor
Information Files (VIFs) needed for USB Type-C
compliance testing.
BUG=chromium:701852
BRANCH=none
TEST=make -j buildall
Compared generated VIFs to expected values
Change-Id: I600ca78b9fb5d2de78aa65a58264c6f79b36ea17
Reviewed-on: https://chromium-review.googlesource.com/455280
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
According to the new MCU secure update model, EC should wait for host if
reset source is reset-pin.
BRANCH=none
BUG=b:37584134
TEST=on rose, toggle reset pin from host. EC should stay in RO, showing
[0.426089 Hard pin-reset detected, disable RW jump]
in console.
Change-Id: Ie1908cb0744773e2e3ca8b3d8c627b8a9ef4567f
Reviewed-on: https://chromium-review.googlesource.com/485199
Commit-Ready: Wei-Ning Huang <wnhuang@chromium.org>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
1. PD vender suggests to use chip default address setting (0x16).
2. Clean up board_print_tcpc_fw version function and related define.
BRANCH=None
BUG=None
TEST=Plug in type-c device and check behavior
Change-Id: I44b7156c914b8de67630696e4534147cc3b7f2c3
Reviewed-on: https://chromium-review.googlesource.com/469449
Commit-Ready: Lin Cloud <cloud_lin@compal.com>
Tested-by: Lin Cloud <cloud_lin@compal.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
(Optionally) split rwsig verification into a separate task. This
allows us to initialize other components (e.g. USB) while the
verification is in progress, speeding up the boot process to active
USB in RO case.
After CONFIG_RWSIG_JUMP_TIMEOUT, the EC will jump to the RW section
if no action is taken by the AP (such as a forced request to jump
to RW, or starting an update).
Note: This comes with a ~36ms boot time regression, as other code
gets to run before verification starts.
BRANCH=none
BUG=b:35587171
TEST=Flash, board boots to RW after 1s
TEST=Change jump timeout to 5s, add 5s delay in check_signature,
add console command to manually abort/continue rwsig verification.
'rwsig continue' works => Board jumps to RW after check_signature
is completed (or immediately while waiting for timeout)
'rwsig abort' works => Board does not jump to RW.
Change-Id: Ica5732b9298bb4d3b743cae2ba78df259db915ef
Reviewed-on: https://chromium-review.googlesource.com/468709
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Follow-up to CL:456520, addressing a few more comments.
BRANCH=none
BUG=b:35775099
TEST=sysrq available in EC console
TEST=sysrq h => help message in AP console
TEST=sysrq b => AP reboots
Change-Id: I692afa7c911882f00d92b8e6d83889c52821e171
Reviewed-on: https://chromium-review.googlesource.com/468506
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Implement actual rollback protection. First, we add a new field
in the version structure, which is an incrementing integer
(we'll start by shipping images with version 0, and gradually
increase the number as required). This allows us to release
new versions of the EC without necessarily bumping the rollback
protection.
For the rollback protection block itself, it contains 2 sub-blocks
of equal size (normally, 2k), that are individually erasable.
The rollback code looks at both, and takes the most restrictive one
to determine the desired rollback minimum version. The blocks
are also allowed to be erased (full of 1's), in which case the
rollback minimum version is assumed to be 0.
We also add an FMAP entry, in case we later decide to allow the
signer to increment the rollback version.
Also note that, like any version_data struct change, this change
breaks compatibility between old and new RO/RW.
Follow-up code will take care of auto-updating the rollback block
as required, and properly manage block protection.
BRANCH=none
BUG=b:35586219
TEST=Flash hammer
rollbackinfo => 1 version 0 block, 1 empty block, RW verifies
correctly.
rollbackupdate 0; rollbackinfo => No change
rollbackupdate 1; reboot => RO refuses to jump to RW
rollbackupdate 2, 3, 4; rollbackinfo => Writes alternate
between the 2 blocks.
rollbackupdate 2 => Refuses to downgrade version
Change-Id: Ia969afb481a93deb912b9153bdd95ace01ad8fa7
Reviewed-on: https://chromium-review.googlesource.com/452815
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
On keyboard-less design, we will implement a special debug mode,
based on button sequences, to transmit sysrq events to the AP.
This implements the new MKBP event to send sysrq, and a console
command to test it. Later CL will implement debug mode itself.
BRANCH=none
BUG=b:35775099
TEST=sysrq available in EC console
TEST=sysrq h => help message in AP console
TEST=sysrq b => AP reboots
Change-Id: I71d3f77497baf8cc7fac65cd040ce20513b507bc
Reviewed-on: https://chromium-review.googlesource.com/456520
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Allow the board to override the hardcoded 97% value for reporting to
the host (and controlling LED behavior) when the battery is "near full".
When enabling "discharge on ac" with a full battery the battery stops
taking a charge until it reaches ~94% SOC (the actual value is not set
but rather comes from a smart battery status bit) but the user will see
the device as discharging between 97% and 94%.
The host side view can be worked around with a powerd preference.
The LED behavior is all inside the EC, so you end up with the LED showing
discharging when it should not.
If we allow the board to override this to 94% then the LED and host
behavior is consistent.
BUG=b:36024657
BRANCH=none
TEST=make -j buildall
Change-Id: Ie5ab8e41b87101e201073276bf441e25be7daca4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://chromium-review.googlesource.com/450949
Reviewed-by: Scott Collyer <scollyer@chromium.org>
pdcontrol suspend command will be used to prevent tcpm from putting
the chip into sleep while firmware update is taking place. Currently
the command suspends or resumes port 0. This patch makes the command
apply to ports individually.
pd enable console command now takes a port number:
pd <port> enable/disable.
This patch also replaces CONFIG_USB_PD_COMM_ENABLED with _DISABLED.
When it's defined, PD communication is disabled at startup.
Plankton undefines CONFIG_USB_PD_COMM_ENABLED enable, intending to
disable PD communication at startup. Therefore, this patch defines
CONFIG_USB_PD_COMM_DISABLED in its board.h.
BUG=b:35586859
BRANCH=none
TEST=From AP console:
localhost # /tmp/ectool pdcontrol suspend 1
[600.188013 TCPC p1 suspended!]
> pd 1 state
Port C1 CC1, Dis - Role: SNK-UFP State: SUSPENDED, Flags: 0x0020
localhost # /tmp/ectool pdcontrol resume 1
[678.516613 TCPC p1 resumed!]
> pd 1 state
Port C1 CC1, Ena - Role: SNK-UFP State: DRP_AUTO_TOGGLE, Flags: 0x0020
From ec console:
> pd 1 disable
Port C1 disable
> pd 1 state
Port C1 CC1, Dis - Role: SNK-UFP State: DRP_AUTO_TOGGLE, Flags: 0x0020
> pd 1 enable
Port C1 enabled
> pd 1 state
Port C1 CC1, Ena - Role: SNK-UFP State: DRP_AUTO_TOGGLE, Flags: 0x0020
Change-Id: Ia0cc4904ac52adc4b89de20918968c8df78b9c80
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/447968
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Using -O3 optimization level rather than -Os results in a large speed-up
for a minor code size increase for the RSA code with our current GCC
toolchain.
Add the CONFIG_RSA_OPTIMIZED option to do it on platforms which are not
too size-constrained.
On cortex-M4 based STM32L432, I'm measuring a 37 to 40% speed increase
(depending on CPU frequency) for a 200 bytes code size delta.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=manual: benchmark RSA2048 with F4 exponent on STM32L432:
-Os -O3
@16Mhz 185163 us --> 111942 us
@80Mhz 39286 us --> 24582 us
Change-Id: I8c2e4b757f037f4f645fb73ba0faaaa471b24896
Reviewed-on: https://chromium-review.googlesource.com/445218
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
When battery is fully charged, Reef starts discharging to protect
battery and starts charging again when charge level goes down
around 95%. To prevent the battery LED from showing blue with the
charger plugged in, this patch adds a new state for discharge +
nearly full. Reef shows a color indicating battery is full if
an external charger is present.
BUG=b:35775017
BRANCH=none
TEST=Fully charge Electro. Plug in OEM charger. LED lights blue.
Change-Id: I4c7c62f2c51c1d39188d1b271331984e89d5d7a3
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/448961
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
USB uses a special mode the trigger remote wake-up during host
suspend, by setting the K-state on the data differential pair,
and setting a bit in the USB config descriptor attributes field.
Let's enable that so that hammer can wake up host from S3.
BRANCH=none
BUG=chrome-os-partner:62325
TEST=Connect hammer to chell, put chell in S3. Press a key (or use
("kb 3 3 1; kb 3 3 0" in console), or touch trackpad =>
host wakes.
Change-Id: Ib7b1e9047e01869f07ddd771c9c9bc640eef10d6
Reviewed-on: https://chromium-review.googlesource.com/446240
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This follows the basics of what is decribed in
RM0091 Reference Manual 30.5.5 Suspend/Resume events .
We call enable/disable_sleep at suspend/resume, to make
sure the EC stays awake when USB is connected and active.
We also call clock_enable/disable_module, which is stubbed on
stm32f0, but can be used on other devices in the family.
This also fixes interrupt handling in usb_interrupt, by only
clearing interrupt bits that were handled instead of resetting
them all, which is racy, and can potentially lead to issues
if reset comes soon after a resume event.
BRANCH=none
BUG=chrome-os-partner:62325
TEST=build and flash hammer, connect to chell, suspend/resume,
and see that hammer prints USB suspend and USB resume lines.
Change-Id: Ie9d02fd4a114add3ebc98dc9393680bc9a64a522
Reviewed-on: https://chromium-review.googlesource.com/446239
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
ROLLBACK region will be used to store rollback information, and
can be protected independently of RW (it can only be protected when
RO is protected, though).
This is only supported on stm32f0 currently.
BRANCH=none
BUG=chrome-os-partner:61671
TEST=on hammer (stm32f072)
flashinfo => RO+RW not protected
flashwp true; reboot => only RO protected
flashwp all; reboot => RO+RW+RB protected
flashwp noall; reboot => only RO protected
flashwp rw; reboot => only RO+RW protected
flashwp rb; reboot => RO+RW+RB protected
flashwp norb; reboot => RO+RW protected
flashwp all; reboot => RO+RW+RB protected
flashwp norw; reboot => RO+RB protected
TEST=on reef, rb/norb commands not available
Change-Id: I45ffc66d91cf3699ecff025e5114c59a73dc8274
Reviewed-on: https://chromium-review.googlesource.com/430519
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The idea of this flag is to be able to protect/unprotect only the
RW portion of the flash. In the (usual) case where ALL=RO+RW, with
no other region, this makes no difference compared to the existing
EC_FLASH_PROTECT_ALL_* flag, and this flag may not be supported.
This is necessary for futher work, where a ROLLBACK region is added,
so that RW/ROLLBACK can be protected/unprotected individually.
Only support for stm32f0 is added, as this is the target for hammer.
BRANCH=none
BUG=chrome-os-partner:61671
TEST=build and flash hammer (stm32f072)
flashinfo => RO+RW not protected
flashwp true; reboot => only RO protected
flashwp all; reboot => RO+RW protected
flashwp noall; reboot => only RO protected
flashwp rw/norw not available
TEST=enable CONFIG_FLASH_PROTECT_RW
build and flash hammer (stm32f072)
flashinfo => RO+RW not protected
flashwp true; reboot => only RO protected
flashwp all; reboot => RO+RW protected
flashwp noall; reboot => only RO protected
flashwp rw; reboot => RO+RW protected
flashwp norw; reboot => only RO protected
TEST=build and flash reef (npcx)
flashinfo => RO+RW not protected
flashwp true => RO protected
flashwp all; flashinfo => all_now displayed
reboot => RO protected
flashwp rw/norw not available
Change-Id: Ica6f499cf2e8a9345b08ef52c915655a983ffe3c
Reviewed-on: https://chromium-review.googlesource.com/442265
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Keep only the most compact version of the curve25519 code
and remove the remaining unused code for easier compilation.
Do the minimal changes to make it compile in the EC code base,
there should be no real functional changes.
Re-use the wording from BoringSSL include/openssl/curve25519.h for the
header.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:62991
TEST=run x25519 on host (ie 'make run-x25519')
and the STM32L4 target:
make BOARD=eve_fp PROJECT=x25519 TEST_BUILD=y
./util/flash_ec --board=eve_fp --image=build/eve_fp/x25519.bin
execute 'runtest' in the console.
Change-Id: I13dbe453eff39b461effb1b3ffa549afc1749fef
Reviewed-on: https://chromium-review.googlesource.com/444187
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Adam Langley <agl@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Eve P1 is missing the ALS_INT_L signal and so needs to poll the
Si114x. This CL adds a new config option CONFIG_ALS_SI114X_POLLING
that when defined uses a deferred callback to trigger the motion
sensor event that reads sensor registers. The deferred callback uses a
8 msec delay which is ~2x longer than the time required by the sensor
to complete the measurement.
BUG=chrome-os-partner:61470
BRANCH=none
TEST=On Eve verify that light sensor measurments are present with the
'accelinfo on 1000' command.
Change-Id: I212bebf2ceacbac87ccb0734cc4990dbc349b028
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/440377
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
usbpd1 futility image type is deprecated and should not be used for
new designs. This adds proper support for rwsig image type.
Key and signatures are added at linker stage step (futility cannot
directly create such signed images). Thanks to VB21 header, rwsig.c
can now tell how many bytes of the RW image need to be
cryptographically verified, and ensure that the rest is blank (0xff).
BRANCH=none
BUG=chromium:690773
TEST=make BOARD=hammer; flash, RW image is verified correctly.
TEST=make runtests -j
TEST=For the rest of the tests:
Change config option to CONFIG_RWSIG_TYPE_RWSIG
TEST=make BOARD=hammer; flash, hammer still verifies correctly.
TEST=cp build/hammer/ec.RW.bin build/hammer/ec.RW.bin.orig;
futility sign --type rwsig --prikey build/hammer/key.vbprik2 \
build/hammer/ec.RW.bin
diff build/hammer/ec.RW.bin build/hammer/ec.RW.bin.orig
=> Same file
TEST=Add CONFIG_CMD_FLASH, flashwrite 0x1e000, reboot, EC does
not verify anymore.
TEST=dump_fmap build/hammer/ec.bin shows KEY_RO and SIG_RW at
correct locations.
Change-Id: I50ec828284c2d1eca67fa8cbddaf6f3b06606c82
Reviewed-on: https://chromium-review.googlesource.com/441546
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Make FIFO a stack variable to save static memory,
Remove auto_inc argument, always set
Remove constant for rate 0.
Force board to declare sensor private data.
Avoid name collision in stm_mems_common
Include stm_mems_common.h in accel_lis2dh.h, caller only need to
include accel_lis2dh.h.
BUG=none
BRANCH=none
TEST=Compile with discovery_stmems board.
Change-Id: Id52b54dd4ec3cf217247c5511ad5a506067ad293
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/441144
Tested-by: mario tesi <mario.tesi@st.com>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: mario tesi <mario.tesi@st.com>
This removes CONFIG_USB_PD_TCPC_FW_VERSION.
board_print_tcpc_fw_version is removed since it's no longer called.
PD chip info is printed in usb_pd_protocol.c.
BUG=none
BRANCH=none
TEST=buildall. Boot Electro, verify chip info is printed.
Change-Id: I2ff860c2a1b17ceea124644ba8feb356b9cca2eb
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/434911
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Shorten certain long prints and reduce the precision of timestamp prints
when CONFIG_CONSOLE_VERBOSE is undef'd.
BUG=chromium:688743
BRANCH=gru
TEST=On kevin, cold reset the EC, boot to OS, and verify cros_ec.log
contains all data since sysjump and is < 2K bytes (~1500 bytes).
Change-Id: Ia9390867788d0ab3087f827b0296107b4e9d4bca
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/438932
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Current fast charge assumes only one battery voltage threshold range for
charger profile override. However we have multiple battery voltage
threshold ranges for few batteries hence added a code which can consider
multiple battery threshold ranges and choose respective charge profile.
BUG=chrome-os-partner:62653
BRANCH=none
TEST=Manually tested on Electro. Manipulate smp_cos4870 & sonycorp
battery voltage & temperature ranges and observed correct charge
profile is selected.
Change-Id: Icddc047e608cc8f63cd0c19be716e0f7908ca715
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/438804
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds a host command to get PD chip info.
For PS8751, tcpci_get_chip_info will fail if the chip is in
low power mode. It can be woken up by reading a random register
first then wait for 10ms.
This code doesn't have the wake-up read to avoid 10ms delay.
Instead, we call this function immediately after the chip is
initialized because it'll gurantee the chip is awake.
Once it's called, the chip info will be stored in cache, which
can be accessed by tcpc_get_chip_info without worrying about
chip states.
localhost ~ # ectool pdchipinfo 0
vendor_id: 0xaaaa
product_id: 0x3429
device_id: 0xad
fw_version: 0x15
localhost ~ # ectool pdchipinfo 1
vendor_id: 0x1da0
product_id: 0x8751
device_id: 0x1
fw_version: 0x37
BUG=chrome-os-partner:62383
BRANCH=none
TEST=ectool pdchipinfo 0/1. make buildall
Change-Id: I3f1667d00ce1826936d90882ada1df6ed6b0ea37
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/433166
Add driver for acc sensor ST lis2dh/lis2dh12
Support interrupt management for FIFO watermark
Starting to share common code with other devices
like lsm6dsm/lsm6dsl (acc/gyro) or new lis2mdl (mag)
TODO: Add all embedded functions support (click,
tap and so on)
BUG=none
BRANCH=master
TEST=Tested on discovery BOARD with sensor connected on
EC i2c master bus. Added motion sense task on discovery
board task list, added gpio info in board configuration
file and tested with motion sense console commands. Data
for acc seems ok: can successfully change ODR and
full scale range. Also FIFO and interrupt tested
Device tested is lis2dh (lis2dh12 simply differs for low
pin count but share the same registers)
Change-Id: I16abeac3f139a604094b38d8d8b857a62c93a242
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Reviewed-on: https://chromium-review.googlesource.com/412700
Commit-Ready: mario tesi <mario.tesi@st.com>
Tested-by: mario tesi <mario.tesi@st.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
If CONFIG_SPI_NOR_SMART_ERASE is defined will read the sector/block
to be erased first and only initiate the erase operation if not
already in an erased state. The read operation (performed in
CONFIG_SPI_NOR_MAX_READ_SIZE chunks) is aborted early if a
non "0xff" byte is encountered.
Reduced erase time of a mostly erased EEPROM from 44s to 20s (16MB
Winbond part) / 1m22s to 40s (32MB Macronix part) @24MHz.
BUG=None
BRANCH=None
TEST=Built all targets. Successfully flashed various EEPROM images.
Change-Id: I369b1fcf72140663b8dbce5a469ebad27f7571ec
Signed-off-by: Nadim Taha <ntaha@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/437988
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
All boards have been transitioned to charge_state_v2.c
So charge_state_v1.c, HOOK_CHARGE_STATE_CHANGE, and
CONFIG_CHARGER_TIMEOUT_HOURS can be removed
BUG=chrome-os-partner:36272
TEST=make -j buildall
BRANCH=none
Change-Id: I3f20c5198ea75185f9894deb792575a1be31432a
Reviewed-on: https://chromium-review.googlesource.com/435467
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
During shutdown sequence sensor rails can be powered down asynchronously
to the EC hence EC cannot interlock the sensor states with the power down
states. To avoid this issue, defer switching the sensors rate with a
configurable delay if in S3. By the time deferred function is serviced,
if the chipset is in S5 we can back out from switching the sensor rate.
BUG=chrome-os-partner:61489
BRANCH=none
TEST=Manually tested on Electro. Put the device in S5 and observed
no I2C errors printed on EC the console.
Change-Id: I40b75ebbf0d05fafffdfd535962423c3960fafbf
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/433338
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Modified src attach state to enable vbus when debug accessory is
detected.
- servo_v4 has two pd ports, but each port requires a different default
power role. Port 0 can only ever be a SNK, but port 1 which acts is
intended to be a DTS port should default to a SRC so it can be be a
source debug accessory. It may also act as a sink debug accessory, but
is not intended to toggle automatically but will swap roles if
necessary via pd role swap messaging.
- Add hook for ccd enable/disable for DTS mode
BUG=chrome-os-partner:61878
BRANCH=servo
TEST=Manual Verfied that can still build servo_v4 project. All changes
in this CL are contingent on config option CONFIG_USB_PD_DTS being enabled.
Change-Id: Iab968b6fbdfc8f2d155c4f8618921b32f313b9ec
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/428308
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In Sink mode, on the receipt of a GotoMin message,
reduce the current consumption to some minimum level.
BUG=chrome-os-partner:33688
TEST=Manual testing
Used a Kevin, with test routine, to test GotoMin feature
on another Kevin unit.
Test routine:
if (!strcasecmp(argv[2], "gm")) {
ccprintf("send goto min\n");
send_control(port, PD_CTRL_GOTO_MIN);
send_control(port, PD_CTRL_PS_RDY);
}
Kevin with GotoMin feature:
# ectool usbpdpower 0
Port 0: SNK DRP PD 4277mV / 3000mA, max 5000mV / 3000mA / 15000mW
Port 1: Disconnected
After Test routine is executed:
# ectool usbpdpower 0
Port 0: SNK DRP PD 4906mV / 500mA, max 5000mV / 500mA / 2500mW
Port 1: Disconnected
BRANCH=none
Change-Id: Iaac6e19706ceb10ccaff4d602d63fc086c808c8f
Reviewed-on: https://chromium-review.googlesource.com/425728
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add a config option that can be used by chipset to provide PMIC reset
using LDO_EN. This is required for ensuring that the AP is power
cycled properly. Implement the special pmic reset for skylake
chipsets.
BUG=chrome-os-partner:61883
BRANCH=None
TEST=Verified that reboot on EC console resets the AP and does not get
stuck in G3 on poppy.
Change-Id: I5f680fede5cb4effa86243f51edfdea09db4d975
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/431192
Reviewed-by: Duncan Laurie <dlaurie@google.com>
