1) Properly report I2C errors on TMP006 as error, not device-not-powered.
2) Treat clock timeout and bus-busy I2C status as error (previously ignored).
3) If clock timeout or bus-busy, reset I2C master for that bus to clear the
error.
These should help with systems where the thermal I2C bus gets into a
weird state on suspend/resume.
BUG=chrome-os-partner:16262
BRANCH=link
TEST=boot system; 'battery' and 'temps' should give good info
Then run snanda's suspend_stress_test for a while and repeat.
Change-Id: I534be8236a4d6de82575fe6d33a68502ce0a3a95
Original-Change-Id: Iec5d6bbd357d2e5eb3dc3d361c829f353e996ab6
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/38444
Reviewed-on: https://gerrit.chromium.org/gerrit/38659
Reviewed-by: Yung-Chieh Lo <yjlou@chromium.org>
Add an interface to allow the CPU to cap the maximum battery charging
current.
The maximum is removed every time the machine goes to S3 or S5.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=link
BUG=chrome-os-partner:16041
TEST=on Link, plug AC to charge the battery,
then run "ectool chargecurrentlimit 1200" and see
the charging current in "power-supply-info" decreasing to 1.2 A.
Change-Id: I10900e1c264d2db67809638ec0dcb836d721fa75
Reviewed-on: https://gerrit.chromium.org/gerrit/37532
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Reviewed-by: Rong Chang <rongchang@chromium.org>
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
When the system is in S5, it will go to hibernate mode after 1 hour
instead of 24 hours.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=link
BUG=none
TEST=on Link DVT3 with servo connected, turn off the machine and
see the EC going to hibernate after 1 hour (according to EC UART traces)
start the machine and see it boot properly.
Change-Id: I1da87b3e09b90817ce5609f3f74b5969235fb90a
Reviewed-on: https://gerrit.chromium.org/gerrit/37526
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Add i8042 output port commands (0xf0-0xff), I8042_ENABLE_A20 and
I8042_DISABLE_A20.
BUG=chrome-os-partner:13119,
BRANCH=None
TEST=Tested on W7 installer. No KB error shown on EC console.
Change-Id: I9ad1fd7baa10683ef18ccf13faf09dc0cefcca0a
Signed-off-by: Louis Yung-Chieh Lo <yjlou@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/34994
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
They're not x86-specific, so move to the chipset interface.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=x86reset warm, then x86reset cold. Should reboot OS in each case.
Change-Id: Ib571ab916bab16179198a0d054320e59afbae124
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36785
This reduces memory / code size, and gets rid of ifdefs in temp_sensor.c.
BUG=chrome-os-partner:15714
BRANCH=none
TEST=boot system and run 'ectool temps all' every few seconds
- ectool temps all
The numbers should update over time.
Change-Id: Idaac7e6e4cbc1d6689f5d3b607c623a5cc536a4f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36940
The time out value passed to task_wait_event() is signed 32-bit and
thus waiting for 24 hours will cause overflow. Limit max wait time.
BUG=chrome-os-partner:15797
BRANCH=link
TEST=Disconnect AC, shut down system, and close lid. From ec console,
do 'hibdelay 8000' and then wait 2.5 hours. EC should have
hibernated. (8000 is more than twice the max time for
task_wait_event())
Change-Id: I5fa505554182e8bad6399c12a382ff71bb123d8f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/37095
Reviewed-by: Vic Yang <victoryang@chromium.org>
Support the keyscan test functionality on stm32.
Note: This is enabled by default so that it continues to build. But it
is unlikely that we will want this in a shipping image. I suggest we add
the facility for a dev build.
Secondly, the stack has to be larger due to a printf (which admittedly I
could just remove). Should we make the stack size conditional on the
CONFIG? Seems a bit ugly, on the other hand we don't want to waste IRAM.
BUG=chrome-os-partner:12179
BRANCH=none
TEST=manual for now:
On snow:
./ectool keyscan 20000 key_sequence.txt
See that the test passes.
Change-Id: Ic441ca0bde1be9589a924374605e2f146d16f423
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/35118
PWM and temp sensor monitoring want to happen every second,
vs. several times a second for watchdog and LPC.
This is still considerably simpler than having tick functions declare
an interval at which they want to be called, which would require a
RAM-based array of pending tick functions and alarm times. If you
need that level of complexity, you still need a task.
BUG=chrome-os-partner:15714
BRANCH=none
TEST=temporarily add HOOK_TICK and HOOK_SECOND hooks and see that on
LM4, HOOK_TICK is called 4x a second and HOOK_SECOND is called every
second.
Change-Id: I5c09842fd356d3254021486949b2799142068b4f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36938
Commit-Ready: Simon Glass <sjg@chromium.org>
Since it handles not just power button, but also lid switch, AC
detect, and other switches.
No functional changes; just renaming.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=boot system, power on/off with power button
Change-Id: I51628a52293f7207715f5f6bf368a08fe6c3dbce
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36821
And change some direct uart_printf()/uart_puts() output to console
output methods instead. Disable unused comxtest debug command. No
other functional changes.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=boot system; should still see debug output with reset flags
Change-Id: I57fe6bb781a1ba7884afa6d090b74a92f45a53cc
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36835
Adds a new HOOK_TICK event which is called every 250ms (LM4) or 500ms
(STM32). This will be used to consolidate a number of tasks which do
small amounts of work infrequently, and previously needed their own
task functions.
This CL adds the tick task; subsequent CLs will consolidate watchdog
and other tasks into tick hooks.
BUG=chrome-os-partner:15714
BRANCH=none
TEST=taskinfo shows TICK task as lowest priority
Change-Id: I9068ee99d56a5bf5c12afd86ad51998c013f4954
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36908
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't use/need it right now, so reduce code size.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=help; should not see scratchpad in list
Change-Id: I7918882eee02d8c440c58a3ac6cba80acc3d2ac1
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36803
Reviewed-by: Simon Glass <sjg@chromium.org>
We'd defined them in a number of different files. This moves
definitions to timer.h, and uses them everywhere we have large delays
(since 10*SECOND is less typo-prone than 10000000).
Also add msleep() and sleep() inline functions. No need for mdelay()
or delay(), since any delays that long should use sleep funcs instead
of spin-waiting.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=boot system; taskinfo displays similar numbers to before
Change-Id: I2a92a9f10f46b6b7b6571759b1f8ab4ecfbf8259
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36726
Since POWERSTATE is confusing whether it refers to battery power or
system power.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=taskinfo; see CHARGER task
Change-Id: I5a237b1329cace4ce48ae39d8954c08a9912ed4b
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36707
This removes the duplicate uart_emergency_printf() vs. panic_printf()
/ uart_emergency_puts() vs. panic_puts() implementation and saves
~0.5kb of code size.
The other significant change is that uart_flush_output() is now smart
enough to determine if it's in an interrupt; if so, it will spin-flush
the output buffer instead of waiting on the uart interrupt. This
removes the need for a separate panic_flush().
BUG=chrome-os-partner:15579
BRANCH=none
TEST=crash unaligned; should print well-formatted crash dump
Change-Id: Ifae756203dd1881806be563308077c1d68302e1f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36695
Code cleanup; no functional changes.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=boot system to OS; should still boot
Change-Id: Icbb628e60792cbecd073a526cd6f879d9e4b20ab
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36692
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Just code cleanup; no functional changes
BUG=chrome-os-partner:15579
BRANCH=none
TEST=build link and snow
Change-Id: Ib62f805777994b39cd9f47a721f52529bb9399c5
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36573
Reviewed-by: Simon Glass <sjg@chromium.org>
No functional changes.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=plug in USB mouse; is powered when system is on
Change-Id: Icbad3035f384191daa2b6dfae61d78f18ece1d76
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36613
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This copies the parts of sha256.c that we need from vboot_reference,
and removes the explicit dependency on vboot_reference. That
dependency was a good idea when we were doing full verified boot in
the EC, but is now overkill and makes it harder for others to reuse
the EC code. This also lets us call EC functions directly instead of
needing vboot_stub.cc; that reduces code size by ~100 bytes.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=vboot_hash ro, then compare with result of sha256sum build/link/ec.RO.flat
Change-Id: I0f236174291df3e7f3c75e960fe9ab32af305a61
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36589
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
No functional changes. (it might look like
SYSTEM_HIB_MINIMUM_DURATION is a change, but it's not used at present)
BUG=chrome-os-partner:15579
BRANCH=none
TEST=version; chip info should print successfully
Change-Id: Idd7f60a29528e9f6af4f91cd5a556e7336acee9f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36599
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
No functional changes; just clean up comments and remove dead code
BUG=chrome-os-partner:15579
BRANCH=none
TEST=code compiles
Change-Id: Id006ae18f2b26cea1720196f696f937811b6ba5b
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36448
Reviewed-by: Simon Glass <sjg@chromium.org>
Previously, the battery charging algorithm would give the battery
current even when it was requesting 0 mA.
BUG=chrome-os-partner:15573
BRANCH=link
TEST=charge battery and leave AC plugged in
Battery will eventually drop to 99% charged. At that point, it should
request 0mA, not 84mA or 85mA. (When it drops farther, it will really
start requesting charge.)
Change-Id: I464a7c8e857c928dbb9f9595f9c947d565b5f5c6
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36526
Reviewed-by: Rong Chang <rongchang@chromium.org>
BUG=chrome-os-partner:15579
BRANCH=none
TEST=discharge and charge battery; should still work
Change-Id: I97033e5f5ff4289831f9a4400d18730ece3bd99a
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36365
Tidy code. No functional changes.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=discharge battery, then plug AC in and make sure it charges
Change-Id: I4cff018940ecb665be96655d6722f74dd6674f6d
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36359
This fixes build breaks in 'make tests'.
BUG=none
BRANCH=none
TEST=make tests (note that this still fails due to other problems;
will fix those in a followup CL)
Change-Id: I5b5ce52ed6e44ade6051e0a091a6699c0454d61a
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36353
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove unused code paths. Simplify interfaces. Clarify comments.
Split the protocol constants into their own header file (since they're
used only by keyboard.c, not i8042.c, which is really keyboard
buffering... and will be renamed so in a followup CL.)
This cleanup reduces binary size by about 200 bytes.
BUG=chrome-os-partner:15579
BRANCH=none
TEST=type on the keyboard; it should still work.
Change-Id: I6acbab5fe5604b4b0c516ba3622e6f41820985d1
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36271
Previously, all hook functions returned EC_SUCCESS, which was
meaningless because nothing ever looked at the return value. Changing
the return value to void saves ~100 bytes of code size and an equal
amount of source code size.
BUG=none
BRANCH=none
TEST=code still builds; link still boots
Change-Id: I2a636339894e5a804831244967a9c9d134df7d13
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/36372
Previously they reported on the system channel, not the hostcmd channel.
BUG=none
BRANCH=none (affects all platforms, but only affects use of 'chan' ec console command)
TEST=manual
- chan 0x40
- x86reset
- should see HC debug output.
Change-Id: Ie9873db015c94a0198a94ebafad87d51b0f73620
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/35953
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes the timing for the S3 low-power indicator adjustable without
reflashing.
BUG=chrome-os-partner:8039
BRANCH=Link
TEST=manual
Boot, log in, run this to put the lightbar into demo mode:
ectool lightbar demo 1
ectool lightbar seq s3s0
The lightbar should act as though the system is asleep.
Then press the left arrow a couple of times and the down-arrow four or five
times. You should see the red light pulse every 5 seconds or so.
Now run
ectool lightbar params > /tmp/w
Edit /tmp/w to change the timing lines to this:
100 # .s3_ramp_up
100 # .s3_ramp_down
Then run
ectool lightbar params /tmp/w
After a cycle or two, you should see the lightbar flash instead of pulse.
Change-Id: If815ff2fb9a158c0e1f4dbb6a269ad07e122d84c
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/35839
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The charging voltage and current are not necessary zero. Remove the
conditions.
BUG=chrome-os-partner:14094
TEST=Remove the battery with AC connected. LED turns red after 30
seconds.
Plug in AC with battery disconnected. LED turns red after 30 seconds.
BRANCH=link
Change-Id: I754383b05af6de0ceeb706612f1cb534254e47e3
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/35807
Reviewed-by: Rong Chang <rongchang@chromium.org>
Tested-by: Rong Chang <rongchang@chromium.org>
This is hopefully the finally final tweak to the lightbar behavior. It does
this:
* When booting or awakening from sleep, Google colors pulse briefly.
* When the chromebook is fully on, lightbar is dim blue. Every 3-5 seconds,
a pulse of brighter blue sweeps across.
* On battery, the lightbar is not quite as bright, and the sweep goes in the
other direction and is slightly slower. If the battery charge drops below
10%, the lightbar changes from blue to red (but only on battery, not AC).
* When going to sleep (close lid while logged in), lightbar fades to black,
then pulses Google colors, then off.
* While asleep, lightbar does nothing, UNLESS on battery and battery charge
is under 10%. Then it pulses red every 5-8 seconds.
* When shutting off, it just goes black with no special effects.
Other than the slight dimming on battery power, there is no ambient light or
dynamic brightness control.
BUG=chrome-os-partner:8039
BRANCH=Link
TEST=manual
Turn it on, watch the blinky lights. Log in, close the lid, open the lid.
Connect/disconnect AC. The lights should change as described above. Ta Da.
Change-Id: Id174a452639decc4b5eefb9e21b28cf3643529f5
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/35742
Reviewed-by: Randall Spangler <rspangler@chromium.org>
I introduced a glitch in the parameterization CL. This fixes it, and makes
the choice between the gentle throbbing and occasional pulse something that
can be selected as a parameter. Default is the new pulsey style.
BUG=chrome-os-partner:8039
BRANCH=Link
TEST=manual
Using the ectool that's part of this change, run these commands to flip
between suspend and active displays:
ectool lightbar seq s3s0
ectool lightbar seq s0s3
Change the "new_s0" value (0/1) and reload the params with
ectool lightbar params | tee /tmp/w
vi /tmp/w
ectool lightbar params /tmp/w
In each case you'll see some pretty patterns. Pass/Fail is an artistic
decision. No QA required.
Change-Id: I8de0b1b3cc77f65879befe95e110bbbce18846d9
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/35620
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Previously, any command which set the fan duty manually would leave
the PWM RPM controller disabled. Setting the fan back to auto mode
via 'ectool autofanctrl' or 'autofan' or 'ectool pwmsetfanrpm'
wouldn't turn the controller back on. Now it does.
BUG=chrome-os-partner:14307
BRANCH=link
TEST=manual
- Reboot in recovery mode and wait for INSERT screen
- From EC console
fanduty 100 -> fan turns on all the way
faninfo -> mode is duty
fanset 6000 -> fan turns down to a lower level
faninfo -> mode is rpm
fanduty 0 -> fan turns off all the way
faninfo -> mode is duty
(wait a min or so for the system to heat up)
autofan -> fan turns on
faninfo -> mode is rpm
- Reboot normally
- From root shell
ectool fanduty 100 -> fan turns on all the way
ectool pwmsetfanrpm 6000 -> fan turns down to a lower level
Change-Id: I3b07e8b49500f5f8a42f20909d2869cf63987d6d
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/35335
Reviewed-by: Sameer Nanda <snanda@chromium.org>
The remote temperature sensors for case temps are now not used until
they're calibrated by the host. But the EC still tries to control the
fan based on case temps. At best this has no effect because the
sensors haven't been enabled by host calibration. At worst, the host
calibrates them, but doesn't set up the temerature thresholds to
match, so the EC spins up the fan briefly during boot before the host
takes over (annoying), or potentially asserts prochot, shuts the
system down, or triggers a bunch of SMIs (really annoying). It's
safer just to leave these thresholds disabled by default; if the host
wants the EC to use them, it can easily set them at the same time it
sets the remote sensor calibration data.
Also, adjust overheated thresholds up based on snanda's recommendations.
BUG=chrome-os-partner:9193
BRANCH=link
TEST=thermalconf 2 --> should print 0 K for all levels
Change-Id: I5bd1ea65eaefc4d39238b22363176d32663434a0
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/35449
Reviewed-by: Sameer Nanda <snanda@chromium.org>
