In RSA, we often need to actually compute (a*b)+c+d: provide some
assembly optimized functions for that.
With -O3, 3072-bit exponent, lower verification time from 104 ms to
88 ms on STM32F072 @48Mhz.
BRANCH=poppy
BUG=b:35647963
BUG=b:77608104
TEST=On staff, flash, verification successful
TEST=make test-rsa, make test-rsa3
TEST=make BOARD=hammer test-utils test-rsa3, test on board
Change-Id: I80e8a7258d091e4f6adea11797729ac657dfd85d
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1071411
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
We multiply 2 32-bit numbers (and not 64-bit numbers), and then add
another 32-bit number, which makes it possible to optimize the
assembly and save a few instructions.
With -O3, 3072-bit exponent, lower verification time from 122 ms to
104 ms on STM32F072 @48Mhz.
Optimized mac function from Dmitry Grinberg <dmitrygr@google.com>.
BRANCH=poppy
BUG=b:35647963
BUG=b:77608104
TEST=On staff, flash, verification successful
TEST=make test-rsa, make test-rsa3
TEST=Flash test-utils and test-rsa to hammer => pass
Change-Id: I584c54c631a3f59f691849a279b308e8d4b4b22d
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/449024
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Some tests cannot be built on some boards (not enough SRAM,
unusual configuration, etc.). Instead of the long list of
exceptions in test/build.mk that we currently use, allow
each board (or chip) build.mk to set test-list-y, and
only use the default list if it is unset.
BRANCH=poppy
BUG=b:80167548
TEST=make buildalltests -j
Change-Id: I803c691f419451aad4396529302a4805cbe3f9b5
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1074572
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
memchr does not take into account end of string, so the test
`memchr("123", '4', 8)` actually does a buffer overflow. On some
boards, a '4' might be found in the 4 bytes that follow "123", and
the test might fail.
Fix another potential overflow as well.
BRANCH=none
BUG=none
TEST=Flash test-utils to hammer, test passes
Change-Id: I53755c0855bbd5b180801e4198341de1cec7b425
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1071409
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
There are still more ifdef than can be added: this just takes out
the low hanging fruits.
BRANCH=poppy
BUG=b:35647963
TEST=make buildall -j, see that we gain from 0 to 64 bytes on many
boards.
Change-Id: Ibe85b8bfa5d5c22c160e4a6656104256067beee9
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1070948
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In rare cases, it is useful to be able to build tests for all boards:
buildall only builds the main image, but -paladin builders also builds
test cases for each board.
Also remove/fix tests for boards that currently fail.
BRANCH=none
BUG=b:35647963
TEST=make buildalltests -j, wait a long time, tests pass.
Change-Id: Id6d978705a40a2045731cb08ad2ca5d62cc12ebb
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1072218
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In order to be able to recover from the AP and Cr50 getting out of
sync, this logging functionality gives Cr50 a way to track the
state changes of the merkle tree so that the AP can be updated to
the current state as long as it has a recent enough copy.
This involves packing the important information so it can be stored
efficiently on flash, and adding the necessary messages for the
replay.
CQ-DEPEND=CL:895395,CL:929430
BRANCH=none
BUG=chromium:809729, chromium:809745
TEST=cd ~/src/platform/ec && V=1 make run-weaver_ng -j
Change-Id: I40f98de2c8e9706cccb5b922215699f2132fa121
Signed-off-by: Allen Webb <allenwebb@google.com>
Reviewed-on: https://chromium-review.googlesource.com/963773
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
This adds some of the ground work for hardware backed brute force
resistance on Cr50. The feature is called Pinweaver. It will
initially be used to enable PIN authentication on CrOS devices
without reducing the security of the platform. A Merkle tree is
used to validate encrypted metadata used to track login attempts.
The metadata tracks counts of failed attempts, a timestamp of the
last failed attempt, the secrets, and any associated parameters.
Instead of storing the metadata on Cr50 an AES-CTR is used with an
HMAC to encrypt the data so it can be stored off-chip and loaded
when needed.
The Merkle tree is used to track the current state of all the
metadata to prevent replay attacks of previously exported copies.
It is a tree of hashes whose root hash is stored on Cr50, and whose
leaves are the HMACs of the encrypted metadata.
BRANCH=none
BUG=chromium:809730, chromium:809741, chromium:809743, chromium:809747
TEST=cd ~/src/platform/ec && V=1 make run-pinweaver -j
Change-Id: Id10bb49d8ebc5a487dd90c6093bc0f51dadbd124
Signed-off-by: Allen Webb <allenwebb@google.com>
Reviewed-on: https://chromium-review.googlesource.com/895395
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Use RMA public key definition generated based on the binary blob
containing the key and key ID.
Key generation is controlled by the make file in common/, but actual
key blob comes from the board directory.
The structure holding the key and key ID is being modified to allow
initialization using a flat array.
No more need in defining CONFIG_RMA_AUTH_SERVER_PUBLIC_KEY and
CONFIG_RMA_AUTH_SERVER_KEY_ID.
BRANCH=cr50, cr50-mp
BUG=b:73296144, b:74100307
TEST='make buildall' still succeeds.
test RMA server generated authentication codes are accepted when
unlocking RMA.
Change-Id: I8ade94de6eb69b3e49bc5b948dbac20e59962acf
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/990783
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Majority of the chipsets do not have a dedicated GPIO to trigger
AP cold reset. Current code either ignores cold reset or does a warm
reset instead or have a work around to put AP in S5 and then bring
back to S0. In order to avoid the confusion, removed the cold reset
logic and only apreset is used hence forth.
BUG=b:72426192
BRANCH=none
TEST=make buildall -j
Manually tested on GLKRVP, apreset EC command can reset AP.
Change-Id: Ie32d34f2f327ff1b61b32a4d874250dce024cf35
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/991052
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
set_resolution is only used for few sensors and is not exposed to the AP.
Remove definition when sensors have a fixed resolution.
BUG=none
BRANCH=master
TEST=compile, kevin has enough space for perform_calib.
Change-Id: I8482387e135356467edaee44da3a0e47cf1db524
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/961222
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
This patch splits struct fan_t into two parts: base configuration
and RPM configuration. RPMs are expected to be different from
model to model while a base configuration is most likely shared.
BUG=b:73720175
BRANCH=none
TEST=make buildall
Change-Id: Iff17573f110e07e88d097dd848cf91ee98b83176
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/949382
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Nearly every board had a buttons array defined in which its contents had
the standard volume buttons. This commit creates a single common
buttons array that can contain the standard volume buttons and recovery
buttons. If a board has volume up and down buttons, they can simply
define CONFIG_VOLUME_BUTTONS and it will populate the buttons array with
the standard definition. The buttons are active low and have a 30 ms
debounce period. Similiarly, if a board has a dedicated recovery
button, defining CONFIG_DEDICATED_RECOVERY_BUTTON will also populate the
buttons array with a recovery button.
BUG=chromium:783371
BRANCH=None
TEST=make -j buildall.
TEST=Flash a device with CONFIG_VOLUME_BUTTONS, verify pressing volume
buttons still work.
Change-Id: Ie5d63670ca4c6b146ec8ffb64d40ea9ce437b913
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/773794
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The llama is a South American relative of the camel, though the llama
does not have a hump. These sturdy creatures are domestic animals used
by the peoples of the Andes Mountains.
BUG=None
TEST=`make buildall -j`
BRANCH=None
Change-Id: I55dbd8d5b0b14c41e27c4ef473833563f38878c3
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/761298
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Charge port / current selection often needs to be significantly altered
when a battery cannot provide sufficient charge, so have charge_manager
initially enter safe mode. After a battery with sufficient capacity has
been identified, charge manager will leave safe mode, and port / current
selection will return to standard rules.
BUG=chromium:777596
BRANCH=None
TEST=Pass charge_manager unit tests. On kevin, remove battery, attach
Apple PD charger, verify safe mode is not exited and device does not
brown out. Hot-plug battery and verify safe mode is exited. Next,
remove battery, attach to Samus, verify safe mode is not exited and
device doesn't brown out. Hot-plug battery, verify that safe mode is
exited and no active charge port, due to dual-role exclusion.
Change-Id: I7784865750087a037aad8dbbac058b22c77ba6d4
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/733954
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Most boards had an identical implementation for this function,
previously known as board_is_consuming_full_charge(). To reduce copy
paste, let's just move it to common code. Boards that charge ramp
without a battery will have to define their own implementation, but
there probably won't be any boards like that in the near future.
BUG=None
BRANCH=None
TEST=make -j buildall
Change-Id: Ic99a378ac26dfd35d7d718bf9376eacfa8609166
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/748919
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Implement the following required features in the USB PD Rev. 3.0
specification.
Not_supported control message: Inform a port partner that a
particular message is not supported.
Battery capabilities extended message: Report battery design
capacity and last full charge capacity.
Battery status data message: Report battery state of charge
Collision avoidance: New scheme to avoid collisions caused when both
source and sink want to send messages.
Cable communication: Only the VCONN source can communicate with the
cable plug. This is NOT implemented because although the drivers have
the capability of communicating with a cable plug, the PD stack doesn't
currently need to talk to a cable plug. This is okay since the current
PD design doesn't source or sink more than 3 amps and all Type-C cables
are required to be 3 amp capable.
BUG=b:64411727
BRANCH=None
TEST=`make -j buildall`
Passed relevant PD Rev 2.0 compliance tests
Successful PD negotiation with PD Rev 2.0 and 3.0 chargers
Tested with low power none PD charger.
Modified a Kevin to operate as a PD 3.0 charger and sent
all required messages and verified the return messages.
Also tested collision avoidance by verifying that a sink only
transmits when the source indicates it's okay.
Used Twinkie to verify that PD was operating as v3.0.
Signed-off-by: Sam Hurst <shurst@chromium.org>
Change-Id: Ifd77e92ec4e9106236f9221393d2bfb97263d979
Reviewed-on: https://chromium-review.googlesource.com/603003
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
suzy-qable advertises 1.5A, but its actual capability depends on the
host USB port it is attached to. Since suzy-qable is ubiquitous and
other DTS sources may behave in the same way, ramp the input current
limit in order to find a reasonable maximum.
BUG=chromium:770296
BRANCH=None
TEST=Attach suzy-qable to kevin and reef, verify that neither OCs and EC
console via cr50 is available on reef. Also verify donette chargers
kevin at 3A and does not ramp.
Change-Id: Idd0683ede3a44111a01da6b4faab52f388ee82fd
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/693295
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
TCPM will retry sending of source caps on failure and retrying in TCPC
will cause us to violate PD_T_SEND_SOURCE_CAP.
BUG=None
TEST=Attach servo_v4 to twinkie, verify source caps are sent in ~100ms
intervals and not in bursts of four.
BRANCH=servo_v4
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I3264e5578afbde7b9d2c003b6744974329a253d4
Reviewed-on: https://chromium-review.googlesource.com/719729
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The decision on whether to ramp (and how high) depends on the quirks of
charger identification, so move the decision out of board, into the
drivers that implement usb_charger.
Also, rename CONFIG_CHARGE_RAMP to CONFIG_CHARGE_RAMP_SW, to better
contrast with the existing CONFIG_CHARGE_RAMP_HW.
BUG=None
TEST=Manual on kevin, verify ramp occurs when port plugged into Z840
workstation.
BRANCH=None
Change-Id: I5b395274133837a18a4f4ac34b59b623287be175
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/702681
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
A couple of bugs have crept in with the latest series of patches:
- the board ID value endianness does not have to be changed
- the test RMA server public key value is wrong
BRANCH=cr50
BUG=b:67007905
TEST=the generated challenge is now accepted by the server, and the
generated auth code matches between the server and the Cr50.
Change-Id: I18f413ab0bcc14d9cc50b115ac3784fdfcd5851c
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/700798
Reviewed-by: Michael Tang <ntang@chromium.org>
Enable necessary flags for the Cr50 to start supporting RMA
authentication. This also requires that the RMA server public key
definition is split between the actual and test. Even though they are
the same at this time, the actual public key would be defined in the
new future and it would be different from the test key.
BRANCH=cr50
BUG=b:65253310
TEST=make buildall -j passes. More tests were conducted on the full
patchset.
Change-Id: I5a3f9d8c71374d78192e3f0a2752391b842da962
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/691554
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The new vendor command operates in two modes: when received with a
zero size payload, it triggers the Cr50 to generate a new RMA
authentication challenge and the expected authentication code value.
When receive with the payload, it compares the received payload with
the pre-calculate authentication code, and returns to the host the
comparison result (passed/not passed).
A care is taken not to accept payload until at least there is a valid
calculated auth code present (to avoid reporting a match on a payload
of all zeros).
Test config needed to be modified to allow compiling of the ccprintf
wrapper.
BRANCH=cr50
BUG=b:37952913
TEST=with the rest of the patches applied observed expected behavior
of generating challenge/response and verifying the auth code.
Change-Id: I30638b0ceef68830565f222dd1f4af17cfc8d7ef
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/690992
Different devices could have different sized unique device IDs. Let's
just use the IDs as is if they are no larger than the
rma_challenge:device_id field, or the first 8 bytes of the HMAC_sha256
value of the unique device ID, where the unique device ID is used both
as the key and the payload.
The server expects the board ID field in big endian format, let's swap
it before calculating the RMA auth challenge.
The test's server side implementation needs to be also adjusted.
BRANCH=cr50
BUG=b:37952913
TEST=make buildall -j passes. With the rest of the patches applied RMA
authentication process generates sensible values.
Change-Id: Ia1fbf9161e01de30a2da8214258008f6e5f7d915
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/690991
Reviewed-by: Michael Tang <ntang@chromium.org>
To implement rtc driver for some ec chips, we
need to convert between calandar date and seconds
(since epoch time, 01-01-1970 00:00:00).
Sicne these functions are HW-independent, let's add
common/rtc.c, include/rtc.h, and unit test for this.
BUG=b:63908519
BRANCH=none
TEST=make buildall test -j
Change-Id: Icb1e768d2b3674d5225b83e09475e984eb104d06
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/666985
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
The TPM test directory has bitrotted and does not compile any more,
leave alone pass tests. This patch updates the tests to match changed
EC codebase:
test/tpm_test/Makefile - look for include files in more directories
test/tpm_test/bn_test.c - add implementation of always_memset() which
for the EC tree now comes from a different tree and provide a plug
for watchdog_reload() which is no used by dcrypto code (which in
fact is not a good idea, but an issue for another day).
test/tpm_test/hash_test.py - update to match new format of return messages
test/tpm_test/upgrade_test.py - update to match the new format of
return messages and limit the test to installing just 2K worth of
data
BRANCH=cr50
BUG=none
TEST=./test/tpmtest/tpmtest.py now passes
Change-Id: Ibcd7fcfba06cd83023e35a2ac4f37ec896492ad4
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/665322
Reviewed-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
The modified CRC8 implementation didn't detect some errors. For
example, using the modified CRC8: CC5QQLALU and DC5QQLALU calculates
to the same value.
BUG=b:37952913
BRANCH=none
TEST=make buildall
Used online CRC-5-USB calculator to test several values against
this implementation.
Signed-off-by: Sam Hurst <shurst@chromium.org>
Change-Id: I5a17941e25691872a25b41525f65f36e2ed1d4fa
Reviewed-on: https://chromium-review.googlesource.com/660812
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Michael Tang <ntang@chromium.org>
Chromebox ECs performs EFS: verifying firmware before the AP boots.
This patch updates host commands which are required for the EFS.
The change includes:
* Update EC_CMD_FLASH_REGION_INFO to accept EC_FLASH_REGION_UPDATE
* Update EC_CMD_VBOOT_HASH to accept EC_VBOOT_HASH_OFFSET_UPDATE
When EC_FLASHS_REGION_UPDATE is specified, EC_CMD_FLASH_REGION_INFO
returns the slot which currently is not hosting a running RW copy.
When EC_VBOOT_HASH_OFFSET_UPDATE is specified, EC_CMD_VBOOT_HASH
computs the hash of the update slot. This hash covers the entire
region, including the signature at the end.
This patch undefines CONFIG_CMD_USBMUX and CONFIG_CMD_TYPEC
for gru to create space.
BUG=b:65028930
BRANCH=none
CQ-DEPEND=CL:648071
TEST=On Fizz, verify:
1. RW_B is old and updated by soft sync. RW_B is activated and
executed after reboot. System continues to boot to OS.
2. RW_A is old and updated by soft sync. RW_A is activated and
executed after reboot. System continues to boot to OS.
Change-Id: I9ece907b764d07ce94054ba27996e048c665a80a
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/648448
SYSTEM_IMAGE_RW_B hasn't been globally treated as a RW copy.
This change makes EC treat it also as a RW copy.
BUG=none
BRANCH=none
TEST=make buildall
Change-Id: Iae5a9090cdf30f980014daca44cdf8f2a65ea1f2
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/656337
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This patch moves the code which can be shared with other data
verification schemes (e.g. RWSIG) under common/vboot. It also
adds unit tests for it.
BUG=b:38462249
BRANCH=none
TEST=make run-vboot. Verify verification succeeds on Fizz.
Change-Id: Icab4d96dd2c154a12b01c41ebe9b46286b4b590e
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/563463
Reviewed-by: Randall Spangler <rspangler@chromium.org>
RMA auth uses X25519 to generate a relatively small challenge and
response.
Currently, nothing calls the rma_auth code. We'll need console and
TPM vendor commands to do so.
BUG=b:37952913
BRANCH=none
TEST=make buildall
Change-Id: Iec7f2d0e3dc8243f79b009ead16bb3ba9f1bef9d
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/544184
Base32 encoding is used to turn the RMA reset binary
challenge/response into less-typo-prone text, at 5 bits per character.
BUG=b:37952913
BRANCH=none
TEST=make runtests
Change-Id: I474750a20204ba353cea1e91982aa03e8071c0c2
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/544177
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Check that added entropy is at least somewhat acceptable.
BRANCH=none
BUG=b:38486828
TEST=make BOARD=hammer -j tests
./util/flash_ec --board=hammer --image=build/hammer/test-entropy.bin
EC console: runtest, get around 4000/1000 (=4) bits of entropy, value
matches (roughly) the value obtained using the awk script.
TEST=make run-entropy
Change-Id: I88d0e9ec0e38ab3ec70d3e8163b8ac1556df978d
Reviewed-on: https://chromium-review.googlesource.com/523482
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This function will be used to generate some entropy using the
Clock Recovery System.
BRANCH=none
BUG=b:38486828
TEST=make BOARD=hammer -j tests
./util/flash_ec --board=hammer --image=build/hammer/test-entropy.bin
EC console: runtest
TEST=Test fails when no USB connection is active
TEST=Test passes when USB connection is active
TEST=Pasting the values into:
tr ';' '\n' | awk 'BEGIN { e = 0; tot=16384.0 }
{ p = $1/tot; if (p > 0) { e -= p*log(p)/log(2) } }
END { print e }'
shows an entropy > 4 bits per sample.
Change-Id: I2363c7bce42c72c33ef0bf3f099d709ee9c13d13
Reviewed-on: https://chromium-review.googlesource.com/518608
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
utils test is a little too large for hammer's small RO, so we split
it in 2 test: utils and utils_str. Instead of one test that requires
about 8kb extra flash, we have 2 tests that take respectively
3.4kb (utils_str) and 4.6kb (utils) of extra flash.
BRANCH=none
BUG=chromium:726113
TEST=make BOARD=hammer tests -j
util/flash_ec --board=hammer --image=build/hammer/test-utils.bin
runtest => pass
Repeat with test-utils_str.bin
TEST=Before this change:
make runtests -j
./util/run_host_test utils | grep Running | sort > old
Apply this change:
make runtests -j
(./util/run_host_test utils; ./util/run_host_test utils_str) \
| grep Running | sort > new
diff old new => No difference (except timing)
Change-Id: I917d572e671d6ce0a8799508761f55de7bd83133
Reviewed-on: https://chromium-review.googlesource.com/514604
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
When the charge ramp task starts, it starts up in the DISCONNECTED
state. From this state, it's possible to set the input current limit to
0 mA. However, upon task start, we shouldn't take any action until we
have valid values from a new charge supplier or a supplier leaving.
This commit changes the charge ramp task to not touch the input current
limit until the charge ramp state changes or the desired input current
changes at least once.
BUG=b:36468002
BRANCH=gru,master
TEST=Flash kevin EC RW or build AP FW that contains the fix that will by
sync'd by EC SW sync. Make sure WP is asserted to prevent PD
communications in RO. Unplug battery. Plug in AC, verify that system
can boot up to UI on AC alone.
TEST=make -j buildall
Change-Id: I351917bce7902c49d1bb842a0cc83dd161d75b6f
Reviewed-on: https://chromium-review.googlesource.com/461382
Commit-Queue: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/463927
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
