Add the Silicon Image sensors, add it to the motion_sense module
to be used with the FIFO.
BRANCH=smaug
TEST=Check light and proxy on Smaug:
Check Light value in Lux are reasonable.
Check Proxy is detecting object, but value are in opposite of distance.
BUG=chrome-os-partner:32829
Change-Id: I11419a0f0613f0fae9323f99deedf5a1e6c6e29c
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/291335
Reviewed-by: Sheng-liang Song <ssl@chromium.org>
Add support for ADC / thermistor reads on the BD99992GW PMIC.
BUG=chrome-os-partner:42156
TEST=Manual on Glados with subsequent commit. Boot to S0, run "temps".
Verify that temperatures start around 28C and begin to increase after
system is powered-on for a long duration.
BRANCH=None
Change-Id: Ic15f41046130317a0e0c3bce4a923ba624328c0d
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/289935
Reviewed-by: Alec Berg <alecaberg@chromium.org>
BUG=none
BRANCH=none
TEST=Added OPT3001 config to test the sensor in Kunimitsu.
Able to read the als data from "als" console command.
Varied the light intensity and the als reading are changing.
Driver fits into the existing ALS framework.
Change-Id: Idb2e6f9f50b6d0d6c8f64c11336efd3f2c76d498
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/286782
Reviewed-by: Shawn N <shawnn@chromium.org>
Initial support for Parade PS8740 Type-C redriving switch.
BUG=chrome-os-partner:41696
TEST=Manual on Glados in subsequent commit. Verify set() and get()
functions set and return consistent values. Verify that USB SS device
functions when muxes are set to dock or USB.
BRANCH=None
Change-Id: Iedbe53cc76f30ecd969c2ca99a7377ed3b193729
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/282280
Reviewed-by: Alec Berg <alecaberg@chromium.org>
In preparation for adding support for additional USB-C mux chips, add a
new high-level USB-C mux interface usb_mux.c. usb_mux functions are now
called from pd code instead of board-level functions. usb_mux calls down
into a mux chip-specific driver (currently pi3usb30532) or
board-specific drivers which toggle GPIOs (for legacy boards).
BUG=chrome-os-partner:41696
TEST=Manual on Glados in subsequent commit. Verify set() and get()
functions set and return consistent values. Verify that USB SS device
functions when muxes are set to dock or USB. Also, verify that DP
dongle and USB SS device are functional on both PD ports on samus_pd.
BRANCH=None
Change-Id: Ib6477f489310f3be1430585ea09fea26f57e3752
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/281435
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Create driver/tcpm/ folder to hold TCPM drivers. Currently the
two drivers are a stub driver which is used when TCPM and TCPC
are on the same MCU and can make direct calls between the two
and the TCPCI driver which implements the standard TCPCI protocol.
BUG=chrome-os-partner:41842
BRANCH=none
TEST=make -j buildall
Change-Id: Ie4d9b36eb33155254f8b87b83861f98a7a80693a
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/281630
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Now that we've removed boards from ToT, also delete board-specific
code used only by the removed boards.
There are still more things to remove (unused charging chips, LED
drivers, COMx support). More CLs coming.
BUG=chromium:493866
BRANCH=none
TEST=make buildall -j
Change-Id: Ie6bdeaf96e61cadd77e3f6336c73b9b54ff4eabb
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/276524
Reviewed-by: Alec Berg <alecaberg@chromium.org>
ISL9237 is a buck-boost narrow output voltage DC charger. This change
provides interfaces to satisfy external dependencies for
charge_state_v2.
ISL9237's charging voltage control is different from smart battery
chargers. And there's no SBC compatible charging mode and status. So
this CL modified charger_set_voltage() behavior by controlling VSYS
voltage.
BRANCH=none
BUG=none
TEST=ran on reworked glados
Signed-off-by: Rong Chang <rongchang@chromium.org>
Change-Id: Ibbbf805bbbe1ee06f87a41cde3e39acbf2e105b4
Reviewed-on: https://chromium-review.googlesource.com/272882
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Trybot-Ready: Aaron Durbin <adurbin@chromium.org>
Tested-by: Aaron Durbin <adurbin@chromium.org>
Add initial support for Oak rev1 board. This is just the
EC and includes battery charging but does not include
USB PD.
BUG=none
BRANCH=none
TEST=load on oak board and get console
Signed-off-by: Rong Chang <rongchang@chromium.org>
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Change-Id: I626f3921025fbc39ba22b04eeb6dd1084cd70777
Reviewed-on: https://chromium-review.googlesource.com/261678
Basic initialization of BMI160.
Fit into the existing accel/gyro framework.
BUG=chrome-os-partner:36018
BRANCH=none
TEST=Ability to read samples with accelinfo.
Change-Id: I5c86d4c3964eb6f876dd4042e5019195ffcca4ed
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/270454
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
define CONFIG_CMD_BATDEBUG to enable console commands.
If the battery is larger than 6Ah or smaller than 150mAh, scale the parameters
transparently to the user using macros.
BUG=chrome-os-partner:34477
BRANCH=none
TEST=Custom console commands for the fuel gauge
I also used a Logic16 from Saleae and the fuel gauge on hadoken.
Signed-off-by: Myles Watson <mylesgw@chromium.org>
Change-Id: I959d51c3188336e4ad0983528ad7e53a2955a764
Reviewed-on: https://chromium-review.googlesource.com/234285
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Myles Watson <mylesgw@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Myles Watson <mylesgw@chromium.org>
Add initial serial driver for mdcp2850 dp->hdmi converter. Driver
implements 'get information' (cmd:0x40) to provide rudimentary method
to test mcdp for functionality and assert GPIO if successful.
Future CLs may expose more serial functionality if necessary.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:34122
TEST=manual, when compiles with #define MCDP_DEBUG see successful
serial communication and result from get info.
buf:[00]0x04 [01]0x40 [02]0x00 [03]0xbc
...
buf:[00]0x0f [01]0x40 [02]0x00 [03]0x0e
[04]0x00 [05]0x01 [06]0x01 [07]0x00
[08]0x00 [09]0x00 [10]0x00 [11]0x00
[12]0x00 [13]0x00
family:000e chipid:0001 irom:1.0.0 fw:0.0.0
Change-Id: I35f9d9b0437633d1bd6a6c9fa14413bedb12f5c2
Reviewed-on: https://chromium-review.googlesource.com/235930
Trybot-Ready: Todd Broch <tbroch@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
The register format of INA231 and INA219 are very much alike. In our
use case, we only need to use different coversion coefficient.
BRANCH=None
BUG=chrome-os-partner:32764
TEST='ina 0' on Plankton V2.
TEST=Build twinkie.
Change-Id: I9c8e21e30ed844566793dcc1221f865400c3d90d
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/223370
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Previously our accel / gyro drivers assumed that we had exactly two of
each identical part in the system. Some systems may have different
configurations, so allow this to be specified at the board-level.
Note that our motion_sense algorithm currently assumes that we have one
accelerometer in the lid and one in the base -- we'll need to fix that
in another CL.
BUG=chrome-os-partner:27320
TEST=Compile-only. Tested in future Samus commit.
BRANCH=None.
Change-Id: I1fae1f6c578fedebe78b473a5d66a5794ccaae00
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/212321
Reviewed-by: Alec Berg <alecaberg@chromium.org>
This is a complete rewrite of the charge_state task used by x86 platforms.
Rather than having a bunch of state-specific functions, each with their own
error handling and special cases, this is organized like so:
Forever:
1. Read everything we can from the battery and charger.
2. Figure out what we'd like to do (including error handling).
3. Allow for customization to override that.
4. Do it.
Things I need to file bugs for are marked with "TODO(wfrichar)". I'll file
the bugs after this CL goes in, so that they'll have something relevant to
refer to.
BUG=chrome-os-partner:20881
BRANCH=ToT
TEST=manual
make buildall -j
Try it on Samus, watch it charge from nearly empty to full, both with and
without fastcharge enabled.
Also undefine CONFIG_BATTERY_PRESENT_CUSTOM, plug and unplug the battery to
be sure the trickle charging logic is correct when it can't tell if the
battery is present.
Change-Id: I3935cd3b87f322eb52178f8a675a886c16b75d58
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/191767
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Add support TI BQ24773 1S/2S/3S NVDC battery charger.
This is not a "Smart Battery" compliant charger IC, it should and cannot
use the sbc_ helpers.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=on FruitPie, run "charger" command on the EC console,
add the charger task and see the battery charging.
Change-Id: I6f470184f0ce424a05007e493d802dcdb2156477
Reviewed-on: https://chromium-review.googlesource.com/191212
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Added accelerometer driver for kxcj9 accelerometers. Currently
the accelerometers aren't being used by anything, but there are
console commands, accelwrite and accelread, to perform transactions.
BUG=none
BRANCH=rambi
TEST=Used EC console commands to test that accelerometers respond
and data looks reasonable.
Original-Change-Id: I6ddcf04ec278adeacb148c19b10c3c296b467954
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/184693
Reviewed-by: Randall Spangler <rspangler@chromium.org>
(cherry picked from commit 5e1d2052b034b2400b98b2126243e01397a2ce56)
Conflicts:
board/clapper/board.c
board/clapper/board.h
board/glimmer/board.c
board/glimmer/board.h
Change-Id: If8744ddc3273fc08e29830adfd068dc302dd120a
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/187432
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This allows local and remote temp values to be added
to a board's list of temp sensors. It also adds a
'tmp432' EC console command to query temps
and set alert thresholds. Fractional degrees are not
supported. DPTF support is not addressed.
BUG=chrome-os-partner:23985
BRANCH=none
TEST=Add tmp432 support to a board with the sensor
then run the 'tmp432' and 'temps' EC console commands.
Signed-off-by: Dave Parker <dparker@chromium.org>
Change-Id: Ifee47cf4d4cf5eedef9ef2bfa2149f183f1d7a7b
Reviewed-on: https://chromium-review.googlesource.com/178688
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Dave Parker <dparker@chromium.org>
Tested-by: Dave Parker <dparker@chromium.org>
This adds the driver and a console command to read an Intersil ISL29305
light sensor connected to the EC.
BUG=chrome-os-partner:23380
BRANCH=samus
TEST=manual
Run the "als" command from the EC console, while pointing the sensor in
various directions. It should give higher numbers when facing a light
source. If you get "Error 1", it means the ALS isn't powered.
Change-Id: I855ed64dab7fc60e29126ab3e97669be24dc6a64
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176056
The common/ subdir was getting cluttered. Move drivers for external
components to a new driver/ tree, and move what used to be called
chipset_*.c to a new power/ directory.
This does not move/rename header files or CONFIG options. That will
be done in subsequent steps, since moving and modifying .c files in
the same CL is harder to review.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards; pass unit tests
Change-Id: I67a3003dc8564783a320335cf0e9620a21982d5e
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/173601
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Tested-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Vic Yang <victoryang@chromium.org>
