For samus, on PD connection or on resume to S0, if we are a sink,
and the other side supports PR_SWAP, then attempt a power swap.
This adds callback functions into board policy file to check
and issue power or data swaps if required by the product.
BUG=chrome-os-partner:31195
BRANCH=samus
TEST=connect samus to zinger and make sure zinger always ends up
as SRC-UFP.
connect samus to samus with both in S0 and see that
they swap power roles once and not data roles.
connect one samus in S0 to one samus in S5 and see that the one
in S5 is sink. then when you boot the one in S5 it switches to a
source.
connect samus to samus with both in S0. do chgoverride 1 on one
side to start charging from the other samus. then on the same
side, turn off the machine (S5) and resume (S0), and see that it
is still charging from the other samus (ie has not switched roles
to source).
Change-Id: Ifab2465fccef77448ac4771a3c2de1c867cbbec4
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/238302
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Previously, handle_vdm_requests could dispatch another VDM message
via send_validate_message prior to main task returning to vdm state machine
(pd_vdm_send_state_machine). While it hasn't been problematic to-date it would
make honoring VDM specific timers or PDO priority difficult.
CL changes behavior so that if VDM being handled requires another VDM to be sent
its copied to the one entry queue (queue_vdm) where it will be
serviced upon VDM state machine entry later.
With this simplification, CL expands interlocks between PDO & VDO.
VDOs are only sent when source/sink is in the ready state & no
incoming packet is on the CC line. PDOs aren't sent when the VDM
state machine is busy.
CL also simplifies VDM console output to come only from request handler which
could save a few bytes.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:30645
TEST=manual,
1. dingdong/hoho still enter mode.
2. Can still update fw.
Change-Id: I2fe8643a6975205b2d0f510f4f1baf2d74c1e190
Reviewed-on: https://chromium-review.googlesource.com/235680
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
This addition allows the AP to query whether the PD device is currently
running from RO or RW FW.
BUG=chrome-os-partner:34599
TEST=Manual on Samus. Run 'ectool --name cros_pd infopddev 0' and verify
that correct RO/RW status of Zinger is printed. Verify that the output
matches the index printed by "pd 1 hash" on samus_pd console.
BRANCH=Samus
Change-Id: I4266cae931f5c7855ca0531717c4a18b138b2d62
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/236771
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Remove common code across all PD policy layers to select the requested
voltage and build a Request Data Object (RDO).
BUG=none
BRANCH=samus
TEST=Load onto samus and connect zinger. Make sure we request the right
voltage (first 5V, then after initial contract is made, 20V). Make
sure input current limit is set appropriately by checking limit on EC
console using charger command.
Change-Id: Ic6bda5e23b2d7b7d710ffdf085e7fbc1b0c3add9
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/233673
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Ensure that the PD source changes the output voltage after
tSnkTransition delay after having sent the ACCEPT message
(rather than before).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:33684
TEST=connect Zinger to a PD power sink and monitor VBUS and CC while
doing a 20V to 5V transition.
Change-Id: If86f59eec67630491f4e8dc13a52015ac2de918a
Reviewed-on: https://chromium-review.googlesource.com/230805
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Allow policy layer to request a PR or DR swap upon formation of
a power contract. Zinger always asks for a data swap so it can
be a UFP, and Samus asks for a data swap only if it is a UFP to
become a DFP.
BUG=chrome-os-partner:33754, chrome-os-partner:31195
BRANCH=samus
TEST=load onto samus and zinger and make sure they swap roles
upon connect with no collisions
Change-Id: I275c9669549c26f25c58f80845daad8edab11313
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/229327
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add support for DR_swap, data role swap command.
BUG=chrome-os-partner:33686, chrome-os-partner:28343
BRANCH=samus
TEST=test with samus and zinger. use "pd 1 swap data" command
and verify data role swaps by using twinkie and "pd 1 state".
Change-Id: I410309199cdeecb26847a6bf217523fdfe688cba
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/229192
Remove redundant 5V source PDOs in source cap packet. We only
need one 5V advertisement with the maximum current that we can
provide.
BUG=none
BRANCH=samus
TEST=make buildall
Change-Id: I94a01813787eb92fafbf600dcbbc8a2f0aa69e2b
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/227392
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Add support for PR_SWAP command as per PD specification.
BUG=chrome-os-partner:28343
BRANCH=samus
TEST=test by connecting two samus' and running 'pd 1 swap power'
from console. verified that both sides switch power roles by
observing console output. also tested against third party
devices.
Change-Id: I0e8738b544de9f9a4348250630e67d0fefb4486d
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/225559
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Update source and sink capacity tables for all PD boards. As
per spec, the first entry in both tables must be a fixed power
supply PDO. Added dual-role capable bit to fixed PDOs and added
new state variable to keep track of that information for each
port. This will be used to make decisions in charge manager and
to pass up via host commands.
BUG=chrome-os-partner:28869
BRANCH=samus
TEST=make buildall. use "pd 1 status" to check
if part partner is dual-role capable and check zinger is not,
C to A receptable adapter is not, and another samus is.
Change-Id: I49f034a372bc145cd524577c17ca210eec4c1013
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/227170
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Previously the version string was special cased in the USB stack
because the build system prevented the inclusion of ec_version.h in
any file other than common/version.c. This lead to common/version.c
being the only place that the USB version string could be computed
and thus the special case of filling in the version string descriptor
at run time. This made the USB stack more complex, and lead to the
common/version.c file including usb.h, which is actually STM32
specific.
Now, the portion of ec_version.h that is deterministic is only
updated when something in the tree actually changes (by way of a
conditional in the makefile), and ec_version.h no longer has to
depend on all object files (other than the special version.o).
This allows anyone to include ec_version.h as needed. In particular,
each board that wants to define a USB version string can directly
include ec_version.h and do so.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
touch files and verify rebuilds happen correctly
Change-Id: Ic84d0b9da90f82ebb4630fb550ec841071e25a49
Reviewed-on: https://chromium-review.googlesource.com/227211
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Added return parameter to enter mode functions. For DP mode on
samus and fruitpie, only send enter mode if device is a DP
sink (DFP_U).
BUG=none
BRANCH=samus
TEST=make buildall. tested a simpler version of this with a
third-party DFP_D capable device and verified we don't send
enter mode.
Change-Id: I5caf008b7b3711232aeb1a1012cde2022584109b
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/225288
Reviewed-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Once alternate mode is entered the DFP will make an initial status
request to the UFP. Future status changes on the UFP are then sent to
the DFP via the attention command. This VDM consists of the VDM
header plus another VDO containing mode specific information.
CL adds ability of DFP to consume the attention VDMs status message
and in the case of DisplayPort SID toggle the necessary HPD gpio
accordingly.
BRANCH=samus
BUG=chrome-os-partner:30645
TEST=manual, for DFP w/ HPD over CC see HPD toggle correctly without
manually driving it providing cable connected when AMA is inserted.
Change-Id: Ifef60b5d0170cbcc1b518e3b13e84bac99a17e32
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/224769
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
A USB type-C to DisplayPort dongle can support either DPv1.3 or
USB Gen 2 signaling.
Our dongles need to advertise that they support DPv1.3 and only this.
Our DFP needs to request DPv1.3 signaling.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:30645
TEST=Plug a type-C to DP dongle from another vendor to Samus and see a
display output.
Change-Id: Ie0ac16b675e86f635220a954a2c03442777cc527
Reviewed-on: https://chromium-review.googlesource.com/225250
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Integrate charge_manager and include several API changes designed
for reporting voltage.
1. Make pd_choose_voltage set the chosen voltage for use by caller.
2. Add voltage parameter to pd_set_input_current.
3. Add pd_get_role to grab the sync / source state of a port.
4. Add charge manager PD + type C port initialization to the pd
state machine.
BUG=chrome-os-partner:32003
TEST=Manual on samus. Insert Apple charger, verify charge limit is
selected appropriately. Insert PD charger, verify that charge port
switches to PD port. Remove + reinsert chargers, verify that port /
limit is selected appropriately. Remove battery, insert power source, verify
that our power source port never becomes disabled.
BRANCH=samus
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Idf3198c71d2ddf1e401e766fc82a4b7a02aed068
Reviewed-on: https://chromium-review.googlesource.com/223758
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Per revisements to the DisplayPort Alternate mode specification there
are two additional SVDMs for DPout support: status & configure.
This CL adds those SVDMs and calls them (status then config) after
finding a device that supports DP Alternate mode.
Future CLs will use these SVDMs to complete providing HPD over CC
support.
BRANCH=none
BUG=chrome-os-partner:31192,chrome-os-partner:31193
TEST=manual, plug hoho/dingdong into samus and see:
1. Additional DP status [16] & DP configure [17]
2. Drives DPout properly
Change-Id: I52b373085ddc330e4afb1d1883d2621bc2e4ee95
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/223260
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
All non-interactive console prints should use their tasks channel
parameter to make it easy for developers to inhibit console output.
This CL corrects printf's in the various usb_pd_policy files that
belong to the USB PD task to use cprintf(CC_USBPD, ...) instead of the
macro reserved for interactive console commands ccprintf.
BRANCH=none
BUG=none
TEST=manual, set 'chan 1' and see none of the previous chatter
relating to USB PD. set 'chan 0x08000000' and see it return.
Output from DFP side for SVDM discovery now looks:
SVDM/4 [1] ff008041 340018d1 00000000 11000008
[1119.966911 DONE]
SVDM/2 [2] ff008042 ff010000
[1119.970135 DONE]
SVDM/2 [3] ff018043 00100081
[1119.973437 DONE]
SVDM/1 [4] ff018184
Change-Id: I47e5f4ec2d4a6a25f171177ead5ebc99409f80b6
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/224191
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
So far, we always use channel 1 of the Tx timer and the configuration
code is hard coded. We need to support other channels for new Ryu
boards. Let's make this a configurable bit.
BRANCH=samus
BUG=chrome-os-partner:32660
TEST=make buildall
TEST=Plug in Zinger to Ryu and see 20V come up.
Change-Id: Id08d4eb0d6a5721d8a03672484d0892a0714383b
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/223836
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Original implementation was complicated by belief that we'd want PD
MCU to manage entry of multiple alternate modes. This simply won't be
practical given the upper level system policies that would need to
weigh in on these decisions as well as the seemingly endless additions
to the alternate mode ecosystem.
Longer term we'll need to pass the generic alternate mode discovery
VDO info to the kernel/userland to implement remainder of policy.
However, for short term lets implement single mode entry instead.
BRANCH=none
BUG=chrome-os-partner:30645
TEST=manual, mode entry is successful on both ports.
Change-Id: Ia24f5ee4d59c13c62d68b30f8587b5e5fbdb2fa0
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/223980
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add support for enabling Vconn on Raiden ports by defining
CONFIG_USBC_VCONN. This is enabled by default for ryu, samus,
and fruitpie.
BUG=chrome-os-partner:30445
BRANCH=samus
TEST=Load onto samus. Make sure we can still charge from zinger.
Plug in type-A to type-C adapter with pulldown and see that samus
becomes power source. Do a gpioget and verify that only one VCONN
GPIO is enabled (low), and the VCONN that is enabled is opposite of
the polarity queried by pd 1 state. Try both ports, both polarities
and make sure the correct VCONN gpio is enabled.
Change-Id: Icea4c18b9c813cf7e8e21fd4f455bbd5fb4dbc91
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/222850
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Remove the meaningless version string in iSerialNumber, which was incorrect
since this string should be unique to a device if it exists.
Export the firmware version string as the configuration string, so it's
traceable to a given firmware build/sources.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=none
TEST=make buildall
from a workstation, do "sudo lsusb -v" and see the full version string
exported as the configuration name.
Change-Id: I557df2936421e2926ac0fc0003888370cec3e201
Reviewed-on: https://chromium-review.googlesource.com/222877
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Change effects:
1. samus_pd: Acts as initiator of SVDM discovery once its reaches source
ready and upon identifying UFP with display port
alternate mode enters that mode.
2. hoho: Acts as responder for SVDM discovery providing its identity,
svids and svid capabilities which are display port only. If
asked to enter display port alternate mode it does.
3. fruitpie: Acts a initiator with mock display port mode.
BRANCH=none
BUG=chrome-os-partner:30645
TEST=manual,
Plug hoho into samus_pd
- see dpout
- from console
> typec 0
Port C0: CC1 451 mV CC2 111 mV (polarity:CC1)
Superspeed DP1
Change-Id: I1a76767353a69baeceffa3e79c37dcea77b8337d
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/221354
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Some platforms may need to take different actions depending on which
port is requesting a limit. Add a new port parameter to the
pd_set_input_current_limit API to accomodate this.
BUG=chrome-os-partner:32003
TEST=Manual on samus_pd. Verify zinger charges battery.
BRANCH=samus
Change-Id: I1578252c751b3a80b4da6ca68e2a958934283cbf
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/222621
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Add support for enabling USB type-C Vconn by defining CONFIG_USBC_VCONN.
Enable Vconn support for samus, ryu, and fruitpie.
BUG=chrome-os-partner:30445
BRANCH=samus
TEST=make buildall
Change-Id: Ibe247286c96fd5a8fa12c88a4e3a5fea02997134
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/222284
Reviewed-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add a minor revision to the PD device hardware ID field in the info
custom VDM and set increment this minor ID from 0 to 1 for zinger.
This differentiates zingers for the auto-update payload, so we can
update only those with a specific major and minor ID version.
BUG=none
BRANCH=samus
TEST=load onto samus and zinger. when connect zinger, see on PD
console: Dev:0x0401 SW:2289 RW:0, which shows the appropriate
device ID.
Change-Id: I482ee2d850332b608cdd81537f68d4dc509bfc1a
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/221320
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Changed sending of info VDM from the UFP side in SNK_DISCONNECTED
to the DFP side in SRC_READY to match the PD spec. Only the DFP
is supposed to send VDMs, and by default the power source is the
DFP. This affects simple DFPs such as power adapters, they must
initiate the info VDM once a power contract has been negotiated.
BUG=none
BRANCH=samus
TEST=load onto samus_pd and zinger and make sure that when you
attached zinger to samus, samus receives info VDM and prints out
something like:
VDM/7 [11] 18d1000b
Dev:1 SW:2280 RW:0
Change-Id: I16ceac31939fdc1c74be7323e628dd8706e1283b
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/221174
Reviewed-by: Todd Broch <tbroch@chromium.org>
OSPEEDR cfg for PB15 was inadvertently set to '01' for PB15 (should be
'00'). Not sure it causes any harm but shouldn't be set according to
comment which is speeding up output pins on SPI interface PB12-14
only.
BRANCH=none
BUG=none
TEST=manual, compiles, boots, talks PD w/ samus_pd.
Change-Id: Ibc2ec1c427a2c3c92ffdf424b668752b1c0b0032
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/217963
Reviewed-by: Vic Yang <victoryang@chromium.org>
PD accessories that are RW update-able will broadcast their rw_hash
SHA1 digest upon connection to the PD MCU which will store it.
For update purposes, the host needs that accessories device id and
rw_hash to determine its proper firmware update payload.
This CL creates a host command that requests the type-C accessory info
attached to a particular port. It also implements an ectool command
to expose the host command.
BRANCH=none
BUG=chrome-os-partner:31361
TEST=manual,
# connect zinger to port 1 on samus
ectool --dev=1 --interface=lpc infopddev 1
Port:0 Device:1 Hash: 0x7f4d7a13 0xf07b65b9 0x41181e10 0xb99b3d5f 0x9dee1206
ectool --dev=1 --interface=lpc infopddev 0
Port:0 has no valid device
Also do the same on port 0 with similar results.
Change-Id: Id63c7edad77a43d43c14d8cd6bd96e08d0d9b501
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/216814
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Every time a type-C source is plugged in, send a special VDM to
read device info. Device info will contain RW Hash (sha1), a
unique hardware descriptor (USB_PD_HARDWARE_DEVICE_ID), a
software version number just for debugging (USB_PD_DBG_SW_VERSION),
and a flag for if the device is in RW. This feature is off by
default and can be turned on by defining
CONFIG_USB_PD_READ_INFO_ON_CONNECT, currently defined for samus
and ryu only.
Renamed the read RW_HASH VDM to READ_INFO since it now returns
more than just the hash.
When device info is received, we store the RW hash. In the future
we will use this to check if device needs an update.
BUG=chrome-os-partner:31361
BRANCH=none
TEST=load onto a samus and a zinger. test when you attach zinger
we send a VDM, and we get device info printed to console. also
use "pd 0 hash" to query last hash received.
Change-Id: I0ca57651cf8506ea738b080a6cf8e7b020ef8724
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/213832
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Set input current limit based on the max current from the
PD negotiation. For samus, this information is passed to
the EC as a host command. For ryu, the max current is set
directly following a negotiation.
CONFIG_CHARGER_INPUT_CURRENT is now just the default limit,
but after a successful PD negotiation, the limit can be
raised.
Note, for now the input current limit for samus is set to
2/3 of the value negotiated for. This is due to hardware
problems measuring input current on p2b boards.
BUG=chrome-os-partner:28532, chrome-os-partner:24461
BRANCH=none
TEST=tested on a samus. Verified input current limit using
"charger" console command from EC. Input current limit
after a reboot is 512. When zinger is plugged in, it jumps
to the appropriate value (currently 1280mA), and when
the negotiation is changed using the "pd 0 dev 5" command
on the PD console, the input current limit is adjusted to
match (2000mA).
Change-Id: Iab9186a0f9814655e3240217a9baf4a38f15f84d
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/211023
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Remove code for preventing PD negotiation until the battery
is at some minimum SOC. This was originally necessary because
transitioning voltages would cause the source voltage to go
briefly to 0V, which would kill power to the system unless
the battery was at some minimum level of charge. But, that
isn't true anymore. It is safe to transition up or down in
voltage and the source voltage should never drop to 0V.
BUG=chrome-os-partner:29499
BRANCH=none
TEST=make -j buildall. No need to do any more testing because
this code has been disabled for a while.
Change-Id: I8a3dca117f01f0f9c7d04b5d489e4a8588a89be6
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/211021
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add console commands to send the Vendor-Defined Messages used to flash a
USB-PD target.
Also add a simple test script to flash Zinger through its CC line. To
run the script, the board must have CONFIG_USB_PD_CUSTOM_VDM defined.
By default fruitpie has this config option enabled.
BRANCH=none
BUG=chrome-os-partner:28330
TEST=With a fruitpie connected to a zinger run
./util/flash_pd.py ./build/zinger/ec.RW.flat
and see Zinger booting on RW.
Change-Id: I06f8f545e28b93b2e646e668d81b594eb7976a2d
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/203375
Reviewed-by: Todd Broch <tbroch@chromium.org>
Previously if you were working on a single board you had to add BOARD=
to all of your make command lines. Now if you are in a board directory
you can just use "make", or "make clean", or any other top level make
command.
This commit also adds support for a top level "make flash" command that
can be used from the board directories as well. This command uses
openocd and requires that the board provides an openocd-flash.cfg file.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=none
TEST=(from a few board directories) make clean; make -j
(from the discovery-stm32f072 directory) make flash
Change-Id: Ie09a74881371169a2c3cd9cd9922f39f4873f1a6
Reviewed-on: https://chromium-review.googlesource.com/209669
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
We have three copies of 'typec' commands in three different boards. The
commands current mix hardware-specific logic and console command logic
together. Adding a board_get_usb_mux() interface to separate the logic
and deduplicate the console command logic.
BUG=None
TEST=make buildall
TEST=Test 'typec' command and verify GPIO settings.
BRANCH=None
Change-Id: Ie1825f49d32609c732db384679cb917f2f1a4082
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/209955
Reviewed-by: Alec Berg <alecaberg@chromium.org>
We used the incorrect src_caps index when choosing PD voltage. Let's fix
it to ask for all available power until we are able to ask only for what
we need.
BUG=None
TEST=make buildall
BRANCH=None
Change-Id: I068264246c2586b8192220eff47838da438899b0
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/207802
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Adds dual USB-PD port support for samus. Both ports are in dual-role
and can perform either role.
Both ports work fine when only one of the ports is in use. But,
still having problems with PD errors on the lower priority port (port
0). If you have a charger plugged into port 0, and a type-C USB dongle
plugged into port 1, then port 1 has higher priority, and in the
SRC_DISCONNECTED state, every 1.5 seconds when it sends source cap
packet, we occasionally drop pings on port 0, which results in a
lot of start/stop charging.
BUG=chrome-os-partner:28585
BRANCH=none
TEST=Tested on samus to make sure both ports work when I
plug in a charger and a type-C USB dongle with a pull-down on the CC
line. Tested on plankton and zinger to make sure PD works as expected.
Change-Id: Ie7bde3e258f5cd23a0b82b626c0993a45b0df074
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/200750
Reviewed-by: Vic Yang <victoryang@chromium.org>
Tested-by: Vic Yang <victoryang@chromium.org>
This is a straightforward conversion of existing tables
into X-Macro style definitions for the GPIO alternate
functions. This change in itself, is not particularly
powerful, but having all GPIO settings in a single file
makes a board easier to understand.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=none
TEST=make buildall -j
Followed by manual testing of interrupt on change and UART
functionality on STM32F0 based discovery board.
Change-Id: Ib7f1f014f4bd289d7c0ac3100470ba2dc71ca579
Reviewed-on: https://chromium-review.googlesource.com/207987
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
The HW signals to control the type-C ports muxing have changed between
Fruitpie and Samus, update the code to match the HW.
Also add the docking mux option and update the board muxing code to
prepare for the automatic mode detection :
- the polarity will be determined by the PD code.
- the port muxing will be enable/disable by the common alternate mode PD
code.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=make buildall
Change-Id: I0706626270c73d2a5e3f85b86e65a7c4fc21f9ec
Reviewed-on: https://chromium-review.googlesource.com/206685
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
this fixes the previous patch to correctly restore the GPIO
BRANCH=none
BUG=none
TEST=verify that GPIO state after restore matches default
Change-Id: I42f73d21399f5e9429dfb50aacb6aba59ba33315
Signed-off-by: Dominic Chen <ddchen@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/206905
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Fix the beginning and end of BMC PD communication:
- Initial transmission within 1us of taking control of CC line
- CC line released between 1us and 23us after last edge
- If final bit is a 0, then add two 1 bits to the end
- No garbage after the final bit
BUG=chrome-os-partner:30132
BRANCH=none
TEST=tested with a fruitpie, samus, and zinger.
verified timing on scope.
Change-Id: Ie45695eb367a7554cf5d5b76b6fbdf1e3fc85d29
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/206453
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
remap DMA at startup, add function to switch mux and set gpio for usb debug
BRANCH=none
BUG=none
TEST=verify that gpio/mux set correctly for debug
Change-Id: I2ca39025c0cba3b5d04946ec4685a81c4de2d49f
Signed-off-by: Dominic Chen <ddchen@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/203493
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
