This unifies the PWM module interface for LM4 and STM32. Now PWM
channels are defined in board.h/board.c. Instead of calling functions
named pwm_set_fan_duty(x), one can now use pwm_set_duty(PWM_CH_FAN, x),
which prevents additional functions added when we have a new PWM
channel.
BUG=chrome-os-partner:18343
TEST=Limit input current on Spring.
TEST=Check power LED in S0/S3/S5 on Snow.
TEST=Check keyboard backlight functionality on Link.
TEST=Check fan speed control/detecting on Link.
BRANCH=None
Change-Id: Ibac4d79f72e65c94776d503558a7592f7db859dc
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/64450
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Problems with existing thermal control loop:
* Not multi-board friendly. thermal.c only supports Link and needs
refactoring. Temp thresholds and fan speeds are hard-coded.
* Only the PECI temp is used to determine the fan speed. Other temp sensors
are ignored.
* Has confusing data structures. Values in the CPU temp thresholds array mix
ACPI thresholds with fan step values.
With this change, the thermal task monitors all temp sensors in order to
perform two completely independent functions:
Function one: Determine if the host needs to be throttled by or informed of
any thermal events.
For thermal events, each temp sensor will have three threshold levels.
TEMP_HOST_WARN
* When any sensor goes above this level, host_throttle_cpu(1) will be called
to ask the CPU to slow itself down.
* When all sensors drop below this level, host_throttle_cpu(0) will be called.
* Exactly AT this level, nothing happens (this provides hysteresis).
TEMP_HOST_HIGH
* When any sensor goes above this level, chipset_throttle_cpu(1) will be
called to slow the CPU down whether it wants to or not.
* When all sensors drop below this level, chipset_throttle_cpu(0) will be
called.
* Exactly AT this level, nothing happens (this provides hysteresis).
TEMP_HOST_SHUTDOWN
* When any sensor is above this level, chipset_force_shutdown() will be
called to halt the CPU.
* Nothing turns the CPU back on again - the user just has to wait for things
to cool off. Pressing the power button too soon will just trigger shutdown
again as soon as the EC can read the host temp.
Function two: Determine the amount of fan cooling needed
For fan cooling, each temp sensor will have two levels.
TEMP_FAN_OFF
* At or below this temperature, no active cooling is needed.
TEMP_FAN_MAX
* At or above this temperature, active cooling should be running at maximum.
The highest level of all temp sensors will be used to request the amount of
active cooling needed. The function pwm_fan_percent_to_rpm() is invoked to
convert the amount of cooling to the target fan RPM.
The default pwm_fan_percent_to_rpm() function converts smoothly between the
configured CONFIG_PWM_FAN_RPM_MIN and CONFIG_PWM_FAN_RPM_MAX for percentages
between 1 and 100. 0% means "off".
The default function probably provide the smoothest and quietest behavior,
but individual boards can provide their own pwm_fan_percent_to_rpm() to
implement whatever curves, hysteresis, feedback, or other hackery they wish.
BUG=chrome-os-partner:20805
BRANCH=none
TEST=manual
Compile-time test with
make BOARD=falco runtests
On the EC console, the existing fan commands should work correctly:
faninfo - display the fan state
fanduty NUM - force the fan PWM to the specified percentage (0-100)
fanset RPM - force the fan to the specified RPM
fanset NUM% - force the fan to the specified percentage (0-100) between
its configured minimum and maximum speeds from board.h
(CONFIG_PWM_FAN_RPM_MIN and CONFIG_PWM_FAN_RPM_MAX)
fanauto - let the EC control the fan automatically
You can test the default pwm_fan_percent_to_rpm() with
fanset 1%
faninfo
The fan should be turning at CONFIG_PWM_FAN_RPM_MIN. Let the EC control it
automatically again with
fanauto
Also on the EC console, the thermal settings can be examined or changed:
> temps
PECI : 327 K = 54 C
ECInternal : 320 K = 47 C
G781Internal : 319 K = 46 C
G781External : 318 K = 45 C
>
> thermalget
sensor warn high shutdown fan_off fan_max name
0 373 387 383 333 363 PECI
1 0 0 0 0 0 ECInternal
2 0 0 0 0 0 G781Internal
3 0 0 0 0 0 G781External
>
> help thermalset
Usage: thermalset sensor warn [high [shutdown [fan_off [fan_max]]]]
set thermal parameters (-1 to skip)
>
> thermalset 2 -1 -1 999
sensor warn high shutdown fan_off fan_max name
0 373 387 383 333 363 PECI
1 0 0 0 0 0 ECInternal
2 0 0 999 0 0 G781Internal
3 0 0 0 0 0 G781External
>
From the host, ectool can be used to get and set these parameters with
nearly identical commands:
ectool thermalget
ectool thermalset 2 -1 -1 999
Change-Id: Idb27977278f766826045fb7d41929953ec6b1cca
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66688
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The BOOTCFG register configures a couple of important things: whether to
allow jumping into the builtin ROM bootloader at reset, and whether or not
to allow JTAG access for programing and debugging.
The default is "no" and "yes". But the BOOTCFG register can be locked so
that it can't be changed again, which means that if the wrong values are put
into it, the system is pretty much bricked.
On Link, we wrote a BOOTCFG value that allowed a GPIO to be used as a bypass
to optionally trigger the ROM bootloader, but on Slippy and its derivatives
that GPIO is not pulled up. If you program the Link values into BOOTCFG on a
Slippy, the system is stuck in the ROM bootloader more or less forever.
This change disables that GPIO, keeps JTAG enabled, and locks those settings
for all LM4 chips (it's a chip config now, not a board config). We've never
actually used the GPIO to invoke the ROM bootloader, but we have managed to
brick a number of systems just by having it enabled, so we're going to lock
it into a safe configuration now.
BUG=chrome-os-partner:19247
BRANCH=falco,peppy
TEST=manual
Reflash, boot, power cycle (actually unplug the EC from AC and battery) a
few times. It should continue to work.
Change-Id: Iaf1a81d6814104421a56425490e3d5164ea9b617
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66538
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
BUG=chrome-os-partner:21847
BRANCH=peppy
TEST=Manual. Check state of GPIO_P5000_FAN_EN with lid open
and lid closed. Can also check with meter via TP109.
Change-Id: I8a64c14d53dd84a5d586c0abb04ccb71de0e78b3
Signed-off-by: Dave Parker <dparker@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65674
Firmware development for this board is happening on the
firmware-wolf-4389.24.B branch.
BUG=chrome-os-partner:21815
BRANCH=None
TEST=Run util/make_all.sh. Verify all is made.
Change-Id: I4b58a982a87562231453f3f201024b809c6a24fb
Signed-off-by: Dave Parker <dparker@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65514
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This just replaces all the "X - 273", "Y + 273" stuff with a macro.
BUG=none
BRANCH=falco,peppy
TEST=manual
Run the EC console command "temps". It should print human-readable things.
Change-Id: Icc4284c89fdbc0cd3b206a0faacf121973652a63
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65005
Reviewed-by: Randall Spangler <rspangler@chromium.org>
GPIO alternate functions used to be configured throughout the code,
which made it hard to tell which ones you needed to configure yourself
in board.c. It also sometimes (chip/lm4/i2c.c) led to GPIOs being
configured as alternate functions even if they weren't used on a given
board.
With this change, every board has a table in board.c which lists ALL
GPIOs which have alternate functions. This is now the only place
where alternate functions are configured. Each module then calls
gpio_init_module() to set up its GPIOs.
This also fixes a bug where gpio_set_flags() ignored most of the flags
passed to it (only direction and level were actually used).
On stm32f, gpio_set_alternate() does not exist, and pins are
configured via direct register writes from board.c. Rather than
attempt to change that in the same CL, I've stubbed out
gpio_set_alternate() for stm32f, and will fix the register writes in a
follow-up CL.
BUG=chrome-os-partner:21618
BRANCH=peppy (fixes I2C1 being initialized even though those pins are used
for other things)
TEST=boot link, falco, pit, spring
Change-Id: I40f47025d8f767e0723c6b40c80413af9ba8deba
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/64400
No functional changes; just moving file
BUG=chrome-os-partner:21612
BRANCH=none
TEST=onewire red / onewire green / onewire yellow all set the adapter LED
(tested on link, since I don't have a bolt, but the EC chip and adapter
are identical)
Change-Id: I005abf871caafa39e82e88875b515c842a12d591
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/64376
Reviewed-by: Vic Yang <victoryang@chromium.org>
There's no need for it to directly access the GPIO registers. That
was only necessary at the beginning of link, when gpio_set_flags()
didn't exist.
BUG=chrome-os-partner:21612
BRANCH=none
TEST=onewire red / onewire green / onewire yellow all set the adapter LED
(tested on link, since I don't have a bolt, but the EC chip and adapter
are identical)
Change-Id: I2386962ff039bb2251be38eaadcaeae8ffd1ea7b
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/64375
Reviewed-by: Vic Yang <victoryang@chromium.org>
Remove support for allowing host command handlers to set the response
pointer. This is just one more thing that can break (and did, on SPI
protocol V2). No commands other than the trivial read-memory-map
command in host_command.c and flash read made use of this capability,
and the savings in performance was negligible.
BUG=chrome-os-partner:21576
BRANCH=none
TEST=boot pit; still boots
Change-Id: I0a9bcf57dbea7155318fc389d7b47d3742a1a00a
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/64236
We've been declaring a bunch of statically-sized arrays:
extern struct foo_t foo[FOO_COUNT];
And then initializing them like so:
struct foo_t foo[FOO_COUNT] = {
/* blah */
};
That only catches cases where we initialize with too many entries. It
doesn't catch cases where we haven't initialized enough. This change tests
for both cases like so:
extern struct foo_t foo[];
struct foo_t foo[] = {
/* blah */
};
BUILD_ASSERT(ARRAY_SIZE(foo) == FOO_COUNT);
The affected arrays are:
adc_channels[ADC_CH_COUNT]
gpio_list[GPIO_COUNT]
temp_sensors[TEMP_SENSOR_COUNT]
x86_signal_list[X86_SIGNAL_COUNT]
i2c_ports[I2C_PORTS_USED]
BUG=chrome-os-partner:18343
BRANCH=falco,peppy
TEST=build all platforms
All platforms should still build, all tests should still pass.
Change-Id: Ibb16dc3201f32df7cdc875648e89ba4ffb09f733
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63833
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Rename onewire_led to led_driver_ds2413, since we may have other LED
drivers hanging off a one-wire bus in the future.
No functional changes, just renaming config options.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: I1d70b1c5778da94bda4ebef3b57f7c39bfba2322
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63273
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
CONFIG_FMAP is now defined by default, because all platforms other
than the host unit tests use it.
No functional changes, just renaming config options and removing dead code.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: Ie6496310c822491068e2fa6976933486f26badb0
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63271
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
To create a token by concatenating already-defined macros and new
text, it's necessary to use multiple levels of macro. We'd already
done that in several places in the code such as STM32_CAT; this now
standardizes it into a single place.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=Build all platforms; examine ec.RO.map to see that irq_*_handler and prio_* symbols
evaluated the same as before. (Other macro evaluations would simply fail to compile
if they were incorrect, since the concatenated tokens wouldn't fully expand.)
Change-Id: Ic9bf11d27881a84507fe7b6096dab6217c6c6dc7
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63231
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The preliminary bolt support allows the board to boot
with all the necessary peripherals working except for the
following things:
- Not all board temp sensors are added.
- WLAN is not powered on because of inrush issues.
- USB power chargers are fixed to normal mode for now.
BUG=chrome-os-partner:20372
BRANCH=None
TEST=Built and booted
Change-Id: Iea7a39e812bb396e5731f212630b7fe97c164bf2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62210
Reviewed-by: Randall Spangler <rspangler@chromium.org>
No functional changes, just renaming config options.
Remove README, now that all options described in it have been moved to
config.h, and the remaining information is out of date. (Yes, we
should have a README which describes the organization of the EC
repository, but that's a matter for another CL; this one's about
cleaning up config options.)
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: Iafefbe94369f1217c698f11d358bc0ecac2bdfde
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63145
Reviewed-by: Vic Yang <victoryang@chromium.org>
All of these were defined on all but a few platforms, and those
explicitly #undef them. So define them as enabled by default in
config.h so the board.h files are cleaner.
No functional changes; just rearranging/renaming config constants.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms; FEATURES=test emerge-falco chromeos-ec
Change-Id: I1201a1472ae29641e9e219c2a0347691ca64cd28
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63102
Reviewed-by: Vic Yang <victoryang@chromium.org>
These are now described in config.h. The various BQ chargers now also
use a consistent naming for their sense resistor options.
No functional changes, just renaming, and removal of obsolete
never-defined configs.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: Ie274546fe45f5ffc6fd0f26096c4622805baf8a0
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62540
This adds two new fields: the ideal write size for best EC flashing
performance (e.g., page mode instead of word mode), and a flags field
with a flag to indicate whether the EC erases its bits to 0 or 1.
The EC still supports the old version 0 command, since u-boot and
flashrom expect that to work.
BUG=chrome-os-partner:20973
BRANCH=(all haswell); this will speed up flashing and software sync
TEST=ectool flashinfo
1. old EC, new ectool -> only reports version 0 info
2. new EC, old ectool -> only reports version 0 info
3. new EC, new ectool -> reports new fields
Change-Id: I484327fe22a58d2b69d7f6ac767b2d3e81b3e0b7
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62378
Reviewed-by: David Hendricks <dhendrix@chromium.org>
There's nothing LM4-specific about the switch module; it's just
checking GPIOs and updating a memory-mapped register.
No code changes; just moving a file.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=verify switch.c is compiled for link and falco, but not pit or spring
Change-Id: I186f3aac1405c7ba8d94b47bb2586c2ad191daba
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61930
Power button logic is common across all platforms and is not
LM4-specific, so move it to its own module. Switch.c will eventually
be moving to common/ and will common across all platforms (not just
x86), and splitting out the x86 power button logic is needed before
that too.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=manual
1) power on system with both lid and power button.
2) power+refresh -> reboots
3) power+refresh+esc -> recovery mode
4) power+refresh+downarrow -> reboots, AP stays off
5) toggling recovery GPIO via servo should generate SW debug output
showing bit 0x10 toggling
Change-Id: I07714e2c035dceece66f90407983397d2697e7d5
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61780
The configure_kblight_gpios() funciton was specific to
the link board. Therefore, move the function to be defined
within the board-specific file.
BUG=chrome-os-partner:20372
BRANCH=None
TEST=Built. Tested similar change on bolt.
Change-Id: Ib5847130450024c50d6526d2c1a64d67ab501637
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62209
This file will soon contain the exhaustive list of all CONFIG defines
and their descriptions.
Chip-level configs are renamed to config_chip.h to avoid naming
conflicts.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: I9e94146f5b4c016894bd3ae3d371c4b9f3f69afe
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62122
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Both of these are included via common.h, which is in turn included by
most other header files. Directly including board.h or config.h is
redundant and discouraged.
No code changes, just removing #includes.
This is in preparation for making a top-level config.h file, but that
change will be easier to review if it doesn't touch as many files.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: I204bcebe5607c6e6808821eb071cfc31d2a93a7c
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62121
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Chipset control of wireless power uses the new API instead of overriding
the wireless power itself.
Refactor board-specific support for it to just a few config #defines
instead of board-specific functions. This makes some assumptions
about the polarity of the enable signals. Not making those
assumptions would require defining an array of structs or some other
heavier-weight board-specific info. Since the assumptions hold for
all current boards, let's make them now because this is a step in the
right direction, and reserve doing something more general until we
actually have a use case for it (so we build in just the flexibility
we need).
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms; see that link wifi turns on at boot and off at
shutdown (verify via 'gpioget' from EC console)
Change-Id: Ic036e76158198d2d5e3dd244c3c7b9b1e8d62982
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61608
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This code is not LM4-specific, it's x86-specific. So it doesn't
belong in chip/lm4. Put it in its own module rather than leaving it
in switch.c, since some x86 systems may need the power button state
machine but not the backlight-enable passthru.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=Quickly run a magnet over the lid switch; the backlight goes off and then
back on.
Change-Id: I72f7139b73f91539dcfbe6b5cb6d56587ab66fde
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61595
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This moves most of the code into a common module, leaving only the
board-specific GPIOs (now listed in a struct in board.c) and the
chipset-specific state machine with multiple copies.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=boot link; verify suspend and resume work; shut back down and see
it go to G3 after 10 sec.
Change-Id: Iafa8ba55a4870bb0119ff4161a1a9054fcc7955f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60949
The AC adapter detection isn't measuring the expected values, most likely
because we're not providing enough current for the ADC circuitry to sample.
This tells the ADC to take 64 samples for every reading and average them
together. That seems to fix it.
BUG=chrome-os-partner:19594
BRANCH=none
TEST=manual
To test, use a scope to probe the voltage pin 6 of the AC adapter connector.
Compare that with the measured result from the ADC, by using the EC
console's "adc" command.
Before this change:
Adapter Probed(mV) ADC(mV) error
45W 469 415 11.5%
65W 600 530 11.6%
90W 794 701 11.7%
After this change:
Adapter Probed(mV) ADC(mV) error
45W 469 452 3.6%
65W 600 590 1.6%
90W 794 773 2.6%
Close enough.
Change-Id: I5ab5526934a5a2711969a90a26631d54c7863da7
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61346
Reviewed-by: Randall Spangler <rspangler@chromium.org>
It previously relied on the switch module to enable/disable the
keyboard backlight when the lid changed position. It can do that itself now.
BUG=chrome-os-partner:20743
BRANCH=none
TEST=Boot link in a dark room where the keyboard backlight is on. Briefly run
a magnet over the lid switch and see the keyboard backlight blink off and
then back on.
Change-Id: Iadf02b780a4990db25b6f0b3e1e0692f49c5488d
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61194
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
These constants are scattered around the various interface
implementations and should be in one place. This will also clean up
the u-boot side when ec_commands.h is copied there.
BUG=chrome-os-partner:20257
BRANCH=none
TEST=build link, spring, pit; test 'ectool hello'
Change-Id: Ib1425db00ec8220538d8c5c65107ac9548009516
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60810
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
As different boards can use the same EC but use different
pins for the same functionality it is required to properly
abstract out the bank and pin used for the one wire interface.
Provide this ability.
BUG=chrome-os-partner:20372
BRANCH=None
TEST=built for failure and success on link
Change-Id: Ie20f2319d9cd6f5ec63b4178ecebc45a90a51042
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60798
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This is necessary to support larger packet sizes for host protocol
ver.3. The host previously didn't have any way to know how big a
packet the EC could accept / respond with (except on LPC, where the
size is determined by the I/O window).
BUG=chrome-os-partner:20257
BRANCH=none
TEST='ectool protoinfo' returns good info; on link,
Protocol info:
protocol versions: 2 3
max request: 256 bytes
max response: 256 bytes
flags: 0x00000000
and on pit,
Protocol info:
protocol versions: 2 3
max request: 544 bytes
max response: 544 bytes
flags: 0x00000001
Change-Id: Ic1e3831d9b4a96ffbf365c0d09b6023472de39a9
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60703
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
When TOT link moved to 128KB images, I missed two references to 80KB.
Fix those, so TOT now builds 128KB images for all lm4-based platforms.
BUG=chromium:252584
BRANCH=none (link branch will stay at 80KB images)
TEST=sysjump rw doesn't crash
Change-Id: I5f25cf97ec706374d03ce8ecff6572c1c84242b5
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60153
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The maximum packet length for LPC is limited by the I/O space window
size. But that's not the case for SPI or LPC. Rename LPC constant
before adding a SPI constant.
BUG=chrome-os-partner:20257
BRANCH=none
TEST=build link
Change-Id: I088327a11eff18d401c773db953700a36f9c1bb4
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59959
This will fix EC flash commands on pit, once the host side (u-boot and
cros_ec driver) are upgraded to match.
This change is backwards-compatible the EC still supports the existing
version 2 protocols for talking to existing AP/kernel/ectool.
Once the AP-side supports version 3 for SPI (and existing systems are
upgraded), we will remove older SPI support since we haven't shipped a
product which uses SPI.
BUG=chrome-os-partner:20257
BRANCH=none
TEST=disable cros_ec driver support in ectool; 'ectool hello' works on link
And with an old ectool which predates this CL, 'ectool hello' also works.
On pit, from u-boot prompt, 'crosec test' and 'crosec version' work, and
keyboard works.
Change-Id: I01f193e316e9aa442fe50d632dc8a4681723e282
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58908
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit-Queue: Doug Anderson <dianders@chromium.org>
Read the value of the WP GPIO correctly.
BUG=chrome-os-partner:20091
BRANCH=none
TEST=manual
On the EC console, run
gpioget WP_L
Short the WP pin, run it again. You should see it change.
Change-Id: Id85c1d69c88ea3df4e529e844aa2455643f1a41b
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58948
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The flags are specific to the LPC interface and not used by the host
command module, so shouldn't be present at that level.
BUG=chrome-os-partner:20185
BRANCH=none
TEST='ectool hello' still works
Change-Id: I6b2c3208fc398ea40d9e7cc7bf5ec206b3e317d8
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58631
Reviewed-by: Vic Yang <victoryang@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
GPIO_HI_Z was a bit misleading (it's high impedance by default, but it's
actually an output not an input), but when we added GPIO_HI_Z_OPEN to mean
"open-drain output, pulled low by default", it got too confusing.
This renames those macros to:
#define GPIO_ODR_HIGH (GPIO_OUTPUT | GPIO_OPEN_DRAIN | GPIO_HIGH)
#define GPIO_ODR_LOW (GPIO_OUTPUT | GPIO_OPEN_DRAIN | GPIO_LOW)
BUG=chrome-os-partner:18788
BRANCH=none
TEST=none
No functional change, just renaming some macros. If it compiles, it should
be unchanged in behavior.
Change-Id: Ic84d7be8531f2b240a8eca4f6cfe5291ebd2d5ef
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58596
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Currently, we need to have #ifdefs everywhere watchdog_reload() is
called. With this fix we don't.
Also don't bother including unused hardware timer watchdog code if the
watchdog isn't defined.
No change when CONFIG_WATCHDOG is defined (which it is for all normal builds).
BUG=chrome-os-partner:20056
BRANCH=none
TEST=build all platforms with CONFIG_WATCHDOG commented out in config.h
Change-Id: Id3ce33af1a497eda127a4892e13651d9d2534d92
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58094
Reviewed-by: Simon Glass <sjg@chromium.org>
The IOUT pin of the smart battery charger can be used to monitor the AC
adapter current (default) or the battery charging current.
BUG=none
BRANCH=none
TEST=manual
Discharge the battery a bit, and connect to the EC console. With the AC
power plugged in, the "battery" command should show charging status,
including current.
The "adc" command will display the A-D converters, including the current
measurement. For example:
> battery
Temp: 0x0b88 = 295.2 K (22.1 C)
Manuf: SMP-COS20
Device: OC2
Chem: LION
Serial: 0x0005
V: 0x4130 = 16688 mV
V-desired: 0x41a0 = 16800 mV
V-design: 0x39d0 = 14800 mV
I: 0x008e = 142 mA(CHG)
I-desired: 0x0080 = 128 mA
Mode: 0x6001
Charge: 98 %
Abs: 94 %
Remaining: 1871 mAh
Cap-full: 1923 mAh
Design: 2000 mAh
Time-full: 0h:23
Empty: 0h:0
>
> adc
ADC channel "ECTemp" = 317
ADC channel "ChargerCurrent" = 455
>
That current is significantly higher than the "I:" reported by the "battery"
command. But look at the charger options:
> sbc 0x12
0x7904 (30980)
>
Bit 5 controls the IOUT Selection. When clear, it monitors the current from
the AC adapter. Set bit 5 to monitor the current provided to the battery:
> sbc 0x12 0x7924
> adc
ADC channel "ECTemp" = 318
ADC channel "ChargerCurrent" = 128
>
That matches what the smart battery sees.
Change-Id: I2fe351304421dfb22d83ef13d416aa44c9f56e8a
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57940
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The ADC pins were being misconfigured for quite a while now. Let's fix 'em.
BUG=none
BRANCH=link
TEST=none
The effect was that the adc values that measure GPIO pins were less
accurate. Since no one noticed, there's probably not much that can
be done to test it.
Change-Id: I9def4eb95c89f72e5df0721e6153c8caa3ef8e2a
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57939
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reading from a nonexistant/nonresponsive smart battery fails (as it should).
But then it leaves the i2c clock line low, so that subsequent i2cscan
commands fail too.
This change just sends a STOP to clear the bus when an i2c error occurs.
BUG=chromium:247037
BRANCH=none
TEST=none
Change-Id: I599bed7149ed3dd3748f1a939c2ea8fdf65e3d72
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57808
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The WAKE# pin was being driven low when the power button was
pressed and no other events were occuring. This causes a PCIE
wake event to be observed on the host. This is incorrect. Therefore
only assert the WAKE# pin when any other event but the power button
has occured.
The implementation introduces a board-specific callback,
board_process_wake_events(), which handles the specific logic
for the wake events.
BUG=chrome-os-partner:19810
BRANCH=None
TEST=Manual. Both power button wakeup and lid events were tested. The
presence of PCIE Wake no longer exists for S5->S0 transitions.
Change-Id: If1311ccc36629b04d2d9e021c3e103e379836a3a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56970
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The firmware defines had two almost-identical sets. Coalesce into one
consistent set.
Link had 256 KB flash, but only allowed 2 80KB images. Future
LM4-based platforms (slippy/peppy/falco/etc) will now use the entire
flash, with RO=124KB, pstate=4KB, RW=128KB. This matches what the
STM32 platforms do, where pstate is contiguous with the RO firmware.
No functional change to STM32-based platforms.
BUG=chrome-os-partner:19176
BRANCH=none
TEST=build all platforms and dump_fmap ec.bin.
- stm32-based platforms should report RO=61440@0, RW=65536@0x10000
- link should report RO=81920@0, RW=81920@0x14000
- slippy should report RO=129024@0, RW=131072@0x20000
Change-Id: I20b1d95c16250d9a5d228ead06eef03d96548823
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56655
