ipq807x: Support for Indio WiFi6 AP -indoor and outdoor models based on IPQ6000

Fixes: WIFI-10802
Signed-off-by: Sohail Ahmad <sohail.ahmad@wifi-soft.com>

feeds/ipq807x/ipq807x/base-files/etc/board.d/02_network

@@ -31,6 +31,9 @@ qcom_setup_interfaces()
 	cig,wf194c|\
 	cig,wf194c4|\
 	edgecore,eap106|\
+	indio,um-310ax-v1|\
+	indio,um-510axp-v1|\
+	indio,um-510axm-v1|\
 	qcom,ipq5018-mp03.3|\
 	yuncore,ax840|\
 	motorola,q14|\
@@ -99,6 +102,9 @@ qcom_setup_macs()
 		ucidef_set_network_device_mac eth1 $lan_mac
 		ucidef_set_label_macaddr $wan_mac
 		;;
+	indio,um-310ax-v1|\
+	indio,um-510axp-v1|\
+	indio,um-510axm-v1|\
 	yuncore,ax840)
 		wan_mac=$(cat /sys/class/net/eth1/address)
 		lan_mac=$(macaddr_add "$wan_mac" 1)

feeds/ipq807x/ipq807x/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -86,6 +86,9 @@ case "$FIRMWARE" in
 	cig,wf196|\
 	edgecore,eap102 |\
 	edgecore,eap106 |\
+	indio,um-310ax-v1|\
+	indio,um-510axp-v1|\
+	indio,um-510axm-v1|\
 	qcom,ipq807x-hk01|\
 	qcom,ipq807x-hk14|\
 	tplink,ex227|\
@@ -173,6 +176,9 @@ ath11k-macs)
 	yuncore,ax840|\
 	edgecore,eap102|\
 	edgecore,eap106|\
+	indio,um-310ax-v1|\
+	indio,um-510axp-v1|\
+	indio,um-510axm-v1|\
 	cig,wf188n)
 		ath11k_generate_macs
 		;;

feeds/ipq807x/ipq807x/base-files/lib/upgrade/platform.sh

@@ -76,6 +76,9 @@ platform_check_image() {
 	cybertan,eww622-a1|\
 	glinet,ax1800|\
 	glinet,axt1800|\
+	indio,um-310ax-v1|\
+	indio,um-510axp-v1|\
+	indio,um-510axm-v1|\
 	wallys,dr6018|\
 	wallys,dr6018-v4|\
 	edgecore,eap101|\
@@ -120,6 +123,9 @@ platform_do_upgrade() {
 	cybertan,eww622-a1|\
 	glinet,ax1800|\
 	glinet,axt1800|\
+	indio,um-310ax-v1|\
+	indio,um-510axp-v1|\
+	indio,um-510axm-v1|\
 	qcom,ipq6018-cp01|\
 	qcom,ipq807x-hk01|\
 	qcom,ipq807x-hk14|\

feeds/ipq807x/ipq807x/files/arch/arm/boot/dts/qcom-ipq6018-indio-um-310ax-v1.dts

@@ -0,0 +1,18 @@
+/*
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "../../../arm64/boot/dts/qcom/qcom-ipq6018-indio-um-310ax-v1.dts"
+#include "qcom-ipq6018.dtsi"

feeds/ipq807x/ipq807x/files/arch/arm/boot/dts/qcom-ipq6018-indio-um-510axm-v1.dts

@@ -0,0 +1,18 @@
+/*
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "../../../arm64/boot/dts/qcom/qcom-ipq6018-indio-um-510axm-v1.dts"
+#include "qcom-ipq6018.dtsi"

feeds/ipq807x/ipq807x/files/arch/arm/boot/dts/qcom-ipq6018-indio-um-510axp-v1.dts

@@ -0,0 +1,18 @@
+/*
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "../../../arm64/boot/dts/qcom/qcom-ipq6018-indio-um-510axp-v1.dts"
+#include "qcom-ipq6018.dtsi"

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq6018-indio-um-310ax-v1.dts

@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qcom-ipq6018.dtsi"
+#include "qcom-ipq6018-rpm-regulator.dtsi"
+#include "qcom-ipq6018-cpr-regulator.dtsi"
+#include "qcom-ipq6018-cp-cpu.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Indio UM-310AX V1";
+	compatible = "indio,um-310ax-v1", "qcom,ipq6018-cp03", "qcom,ipq6018";
+
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	interrupt-parent = <&intc>;
+
+	aliases {
+		/* Aliases as required by u-boot to patch MAC addresses */
+		ethernet0 = "/soc/dp2";
+		ethernet1 = "/soc/dp1";
+
+		serial0 = &blsp1_uart3;
+		serial1 = &blsp1_uart2;
+
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	};
+
+/* TZAPP is enabled only in default memory profile */
+#if !defined(__IPQ_MEM_PROFILE_256_MB__) && !defined(__IPQ_MEM_PROFILE_512_MB__)
+	reserved-memory {
+		tzapp:tzapp@49B00000 {	/* TZAPPS */
+			no-map;
+			reg = <0x0 0x49B00000 0x0 0x00600000>;
+		};
+	};
+#endif
+};
+
+&tlmm {
+	uart_pins: uart_pins {
+		mux {
+			pins = "gpio44", "gpio45";
+			function = "blsp2_uart";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	spi_0_pins: spi_0_pins {
+		mux {
+			pins = "gpio38", "gpio39", "gpio40", "gpio41";
+			function = "blsp0_spi";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	qpic_pins: qpic_pins {
+		data_0 {
+			pins = "gpio15";
+			function = "qpic_pad0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_1 {
+			pins = "gpio12";
+			function = "qpic_pad1";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_2 {
+			pins = "gpio13";
+			function = "qpic_pad2";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_3 {
+			pins = "gpio14";
+			function = "qpic_pad3";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_4 {
+			pins = "gpio5";
+			function = "qpic_pad4";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_5 {
+			pins = "gpio6";
+			function = "qpic_pad5";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_6 {
+			pins = "gpio7";
+			function = "qpic_pad6";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_7 {
+			pins = "gpio8";
+			function = "qpic_pad7";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		qpic_pad {
+			pins = "gpio1",  "gpio3",  "gpio4",
+			       "gpio10", "gpio11", "gpio17";
+			function = "qpic_pad";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	button_pins: button_pins {
+		rst_button {
+			pins = "gpio19";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio64";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio65";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_2 {
+			pins = "gpio75";
+			function = "gpio";
+			bias-pull-up;
+		};
+	};
+
+	modem_power_pins {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+
+	leds_pins: leds_pins {
+		led_blue {
+			pins = "gpio35";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		led_green {
+			pins = "gpio37";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		led_red {
+			pins = "gpio32";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&soc {
+	mdio: mdio@90000 {
+		status = "ok";
+
+		pinctrl-0 = <&mdio_pins>;
+		pinctrl-names = "default";
+		phy-reset-gpio = <&tlmm 75 0>;
+
+		ethernet-phy@0 {
+			reg = <0x03>;
+		};
+
+		ethernet-phy@1 {
+			reg = <0x04>;
+		};
+	};
+
+	ess-switch@3a000000 {
+		switch_cpu_bmp =   <0x01>; /* cpu port bitmap */
+		switch_lan_bmp =   <0x10>; /* lan port bitmap */
+		switch_wan_bmp =   <0x20>; /* wan port bitmap */
+		switch_inner_bmp = <0x80>; /*inner port bitmap*/
+		switch_mac_mode =  <0x00>; /* mac mode for uniphy instance0*/
+		switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
+		switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
+
+		qcom,port_phyinfo {
+			port@3 {
+				port_id = <0x04>;
+				phy_address = <0x03>;
+			};
+
+			port@4 {
+				port_id = <0x05>;
+				phy_address = <0x04>;
+			};
+		};
+	};
+
+	dp1 {
+		device_type = "network";
+		compatible = "qcom,nss-dp";
+		qcom,id = <0x04>;
+		reg = <0x3a001600 0x200>;
+		qcom,mactype = <0x00>;
+		local-mac-address = [00 00 00 00 00 00];
+		qcom,link-poll = <0x01>;
+		qcom,phy-mdio-addr = <0x03>;
+		phy-mode = "sgmii";
+	};
+
+	dp2 {
+		device_type = "network";
+		compatible = "qcom,nss-dp";
+		qcom,id = <0x05>;
+		reg = <0x3a001800 0x200>;
+		qcom,mactype = <0x00>;
+		local-mac-address = [00 00 00 00 00 00];
+		qcom,link-poll = <0x01>;
+		qcom,phy-mdio-addr = <0x04>;
+		phy-mode = "sgmii";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 19 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led_system: system {
+			label = "green:system";
+			gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "blue:wlan2g";
+			gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g {
+			label = "red:wlan5g";
+			gpio = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	pinctrl-0 = <&uart_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&spi_0 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-select = <0>;
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		compatible = "n25q128a11";
+		linux,modalias = "m25p80", "n25q128a11";
+		spi-max-frequency = <50000000>;
+		use-default-sizes;
+	};
+};
+
+&qpic_bam {
+	status = "ok";
+};
+
+&nand {
+	pinctrl-0 = <&qpic_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&nss_crypto {
+	status = "ok";
+};
+
+&cpu0_opp_table {
+	compatible = "operating-points-v2";
+	opp-shared;
+
+	opp03 {
+		opp-hz = /bits/ 64 <1200000000>;
+		opp-microvolt = <3>;
+		clock-latency-ns = <200000>;
+	};
+
+	/delete-node/ opp04;
+	/delete-node/ opp05;
+	/delete-node/ opp06;
+};
+
+/* TZAPP is enabled in default memory profile only */
+#if !defined(__IPQ_MEM_PROFILE_256_MB__) && !defined(__IPQ_MEM_PROFILE_512_MB__)
+&qseecom {
+	mem-start = <0x49B00000>;
+	mem-size = <0x600000>;
+	status = "ok";
+};
+#endif
+
+&ssphy_0 {
+	status = "ok";
+};
+
+&qusb_phy_0 {
+	status = "ok";
+};
+
+&qusb_phy_1 {
+	status = "ok";
+};
+
+&usb2 {
+	status = "ok";
+};
+
+&usb3 {
+	status = "ok";
+};

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq6018-indio-um-510axm-v1.dts

@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qcom-ipq6018.dtsi"
+#include "qcom-ipq6018-rpm-regulator.dtsi"
+#include "qcom-ipq6018-cpr-regulator.dtsi"
+#include "qcom-ipq6018-cp-cpu.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Indio UM-510AXM V1";
+	compatible = "indio,um-510axm-v1", "qcom,ipq6018-cp03", "qcom,ipq6018";
+
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	interrupt-parent = <&intc>;
+
+	aliases {
+		/* Aliases as required by u-boot to patch MAC addresses */
+		ethernet0 = "/soc/dp2";
+		ethernet1 = "/soc/dp1";
+
+		serial0 = &blsp1_uart3;
+		serial1 = &blsp1_uart2;
+
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	};
+
+/* TZAPP is enabled only in default memory profile */
+#if !defined(__IPQ_MEM_PROFILE_256_MB__) && !defined(__IPQ_MEM_PROFILE_512_MB__)
+	reserved-memory {
+		tzapp:tzapp@49B00000 {	/* TZAPPS */
+			no-map;
+			reg = <0x0 0x49B00000 0x0 0x00600000>;
+		};
+	};
+#endif
+};
+
+&tlmm {
+	uart_pins: uart_pins {
+		mux {
+			pins = "gpio44", "gpio45";
+			function = "blsp2_uart";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	spi_0_pins: spi_0_pins {
+		mux {
+			pins = "gpio38", "gpio39", "gpio40", "gpio41";
+			function = "blsp0_spi";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	qpic_pins: qpic_pins {
+		data_0 {
+			pins = "gpio15";
+			function = "qpic_pad0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_1 {
+			pins = "gpio12";
+			function = "qpic_pad1";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_2 {
+			pins = "gpio13";
+			function = "qpic_pad2";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_3 {
+			pins = "gpio14";
+			function = "qpic_pad3";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_4 {
+			pins = "gpio5";
+			function = "qpic_pad4";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_5 {
+			pins = "gpio6";
+			function = "qpic_pad5";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_6 {
+			pins = "gpio7";
+			function = "qpic_pad6";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_7 {
+			pins = "gpio8";
+			function = "qpic_pad7";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		qpic_pad {
+			pins = "gpio1",  "gpio3",  "gpio4",
+			       "gpio10", "gpio11", "gpio17";
+			function = "qpic_pad";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	button_pins: button_pins {
+		rst_button {
+			pins = "gpio19";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio64";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio65";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_2 {
+			pins = "gpio75";
+			function = "gpio";
+			bias-pull-up;
+		};
+	};
+
+	modem_power_pins {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+
+	leds_pins: leds_pins {
+		led_blue {
+			pins = "gpio35";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		led_green {
+			pins = "gpio37";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		led_red {
+			pins = "gpio32";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&soc {
+	mdio: mdio@90000 {
+		status = "ok";
+
+		pinctrl-0 = <&mdio_pins>;
+		pinctrl-names = "default";
+		phy-reset-gpio = <&tlmm 75 0>;
+
+		ethernet-phy@0 {
+			reg = <0x03>;
+		};
+
+		ethernet-phy@1 {
+			reg = <0x04>;
+		};
+	};
+
+	ess-switch@3a000000 {
+		switch_cpu_bmp =   <0x01>; /* cpu port bitmap */
+		switch_lan_bmp =   <0x10>; /* lan port bitmap */
+		switch_wan_bmp =   <0x20>; /* wan port bitmap */
+		switch_inner_bmp = <0x80>; /*inner port bitmap*/
+		switch_mac_mode =  <0x00>; /* mac mode for uniphy instance0*/
+		switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
+		switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
+
+		qcom,port_phyinfo {
+			port@3 {
+				port_id = <0x04>;
+				phy_address = <0x03>;
+			};
+
+			port@4 {
+				port_id = <0x05>;
+				phy_address = <0x04>;
+			};
+		};
+	};
+
+	dp1 {
+		device_type = "network";
+		compatible = "qcom,nss-dp";
+		qcom,id = <0x04>;
+		reg = <0x3a001600 0x200>;
+		qcom,mactype = <0x00>;
+		local-mac-address = [00 00 00 00 00 00];
+		qcom,link-poll = <0x01>;
+		qcom,phy-mdio-addr = <0x03>;
+		phy-mode = "sgmii";
+	};
+
+	dp2 {
+		device_type = "network";
+		compatible = "qcom,nss-dp";
+		qcom,id = <0x05>;
+		reg = <0x3a001800 0x200>;
+		qcom,mactype = <0x00>;
+		local-mac-address = [00 00 00 00 00 00];
+		qcom,link-poll = <0x01>;
+		qcom,phy-mdio-addr = <0x04>;
+		phy-mode = "sgmii";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 19 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led_system: system {
+			label = "green:system";
+			gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "blue:wlan2g";
+			gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g {
+			label = "red:wlan5g";
+			gpio = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	pinctrl-0 = <&uart_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&spi_0 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-select = <0>;
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		compatible = "n25q128a11";
+		linux,modalias = "m25p80", "n25q128a11";
+		spi-max-frequency = <50000000>;
+		use-default-sizes;
+	};
+};
+
+&qpic_bam {
+	status = "ok";
+};
+
+&nand {
+	pinctrl-0 = <&qpic_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&nss_crypto {
+	status = "ok";
+};
+
+&cpu0_opp_table {
+	compatible = "operating-points-v2";
+	opp-shared;
+
+	opp03 {
+		opp-hz = /bits/ 64 <1200000000>;
+		opp-microvolt = <3>;
+		clock-latency-ns = <200000>;
+	};
+
+	/delete-node/ opp04;
+	/delete-node/ opp05;
+	/delete-node/ opp06;
+};
+
+/* TZAPP is enabled in default memory profile only */
+#if !defined(__IPQ_MEM_PROFILE_256_MB__) && !defined(__IPQ_MEM_PROFILE_512_MB__)
+&qseecom {
+	mem-start = <0x49B00000>;
+	mem-size = <0x600000>;
+	status = "ok";
+};
+#endif
+
+&ssphy_0 {
+	status = "ok";
+};
+
+&qusb_phy_0 {
+	status = "ok";
+};
+
+&qusb_phy_1 {
+	status = "ok";
+};
+
+&usb2 {
+	status = "ok";
+};
+
+&usb3 {
+	status = "ok";
+};

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq6018-indio-um-510axp-v1.dts

@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qcom-ipq6018.dtsi"
+#include "qcom-ipq6018-rpm-regulator.dtsi"
+#include "qcom-ipq6018-cpr-regulator.dtsi"
+#include "qcom-ipq6018-cp-cpu.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Indio UM-510AXP V1";
+	compatible = "indio,um-510axp-v1", "qcom,ipq6018-cp03", "qcom,ipq6018";
+
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	interrupt-parent = <&intc>;
+
+	aliases {
+		/* Aliases as required by u-boot to patch MAC addresses */
+		ethernet0 = "/soc/dp2";
+		ethernet1 = "/soc/dp1";
+
+		serial0 = &blsp1_uart3;
+		serial1 = &blsp1_uart2;
+
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	};
+
+/* TZAPP is enabled only in default memory profile */
+#if !defined(__IPQ_MEM_PROFILE_256_MB__) && !defined(__IPQ_MEM_PROFILE_512_MB__)
+	reserved-memory {
+		tzapp:tzapp@49B00000 {	/* TZAPPS */
+			no-map;
+			reg = <0x0 0x49B00000 0x0 0x00600000>;
+		};
+	};
+#endif
+};
+
+&tlmm {
+	uart_pins: uart_pins {
+		mux {
+			pins = "gpio44", "gpio45";
+			function = "blsp2_uart";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	spi_0_pins: spi_0_pins {
+		mux {
+			pins = "gpio38", "gpio39", "gpio40", "gpio41";
+			function = "blsp0_spi";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	qpic_pins: qpic_pins {
+		data_0 {
+			pins = "gpio15";
+			function = "qpic_pad0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_1 {
+			pins = "gpio12";
+			function = "qpic_pad1";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_2 {
+			pins = "gpio13";
+			function = "qpic_pad2";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_3 {
+			pins = "gpio14";
+			function = "qpic_pad3";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_4 {
+			pins = "gpio5";
+			function = "qpic_pad4";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_5 {
+			pins = "gpio6";
+			function = "qpic_pad5";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_6 {
+			pins = "gpio7";
+			function = "qpic_pad6";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		data_7 {
+			pins = "gpio8";
+			function = "qpic_pad7";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		qpic_pad {
+			pins = "gpio1",  "gpio3",  "gpio4",
+			       "gpio10", "gpio11", "gpio17";
+			function = "qpic_pad";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	button_pins: button_pins {
+		rst_button {
+			pins = "gpio19";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio64";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio65";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_2 {
+			pins = "gpio75";
+			function = "gpio";
+			bias-pull-up;
+		};
+	};
+
+	modem_power_pins {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			output-high;
+		};
+	};
+
+	leds_pins: leds_pins {
+		led_blue {
+			pins = "gpio35";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		led_green {
+			pins = "gpio37";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		led_red {
+			pins = "gpio32";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&soc {
+	mdio: mdio@90000 {
+		status = "ok";
+
+		pinctrl-0 = <&mdio_pins>;
+		pinctrl-names = "default";
+		phy-reset-gpio = <&tlmm 75 0>;
+
+		ethernet-phy@0 {
+			reg = <0x03>;
+		};
+
+		ethernet-phy@1 {
+			reg = <0x04>;
+		};
+	};
+
+	ess-switch@3a000000 {
+		switch_cpu_bmp =   <0x01>; /* cpu port bitmap */
+		switch_lan_bmp =   <0x10>; /* lan port bitmap */
+		switch_wan_bmp =   <0x20>; /* wan port bitmap */
+		switch_inner_bmp = <0x80>; /*inner port bitmap*/
+		switch_mac_mode =  <0x00>; /* mac mode for uniphy instance0*/
+		switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
+		switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
+
+		qcom,port_phyinfo {
+			port@3 {
+				port_id = <0x04>;
+				phy_address = <0x03>;
+			};
+
+			port@4 {
+				port_id = <0x05>;
+				phy_address = <0x04>;
+			};
+		};
+	};
+
+	dp1 {
+		device_type = "network";
+		compatible = "qcom,nss-dp";
+		qcom,id = <0x04>;
+		reg = <0x3a001600 0x200>;
+		qcom,mactype = <0x00>;
+		local-mac-address = [00 00 00 00 00 00];
+		qcom,link-poll = <0x01>;
+		qcom,phy-mdio-addr = <0x03>;
+		phy-mode = "sgmii";
+	};
+
+	dp2 {
+		device_type = "network";
+		compatible = "qcom,nss-dp";
+		qcom,id = <0x05>;
+		reg = <0x3a001800 0x200>;
+		qcom,mactype = <0x00>;
+		local-mac-address = [00 00 00 00 00 00];
+		qcom,link-poll = <0x01>;
+		qcom,phy-mdio-addr = <0x04>;
+		phy-mode = "sgmii";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 19 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led_system: system {
+			label = "green:system";
+			gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "blue:wlan2g";
+			gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g {
+			label = "red:wlan5g";
+			gpio = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	pinctrl-0 = <&uart_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&spi_0 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-select = <0>;
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		compatible = "n25q128a11";
+		linux,modalias = "m25p80", "n25q128a11";
+		spi-max-frequency = <50000000>;
+		use-default-sizes;
+	};
+};
+
+&qpic_bam {
+	status = "ok";
+};
+
+&nand {
+	pinctrl-0 = <&qpic_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&nss_crypto {
+	status = "ok";
+};
+
+&cpu0_opp_table {
+	compatible = "operating-points-v2";
+	opp-shared;
+
+	opp03 {
+		opp-hz = /bits/ 64 <1200000000>;
+		opp-microvolt = <3>;
+		clock-latency-ns = <200000>;
+	};
+
+	/delete-node/ opp04;
+	/delete-node/ opp05;
+	/delete-node/ opp06;
+};
+
+/* TZAPP is enabled in default memory profile only */
+#if !defined(__IPQ_MEM_PROFILE_256_MB__) && !defined(__IPQ_MEM_PROFILE_512_MB__)
+&qseecom {
+	mem-start = <0x49B00000>;
+	mem-size = <0x600000>;
+	status = "ok";
+};
+#endif
+
+&ssphy_0 {
+	status = "ok";
+};
+
+&qusb_phy_0 {
+	status = "ok";
+};
+
+&qusb_phy_1 {
+	status = "ok";
+};
+
+&usb2 {
+	status = "ok";
+};
+
+&usb3 {
+	status = "ok";
+};

feeds/ipq807x/ipq807x/image/ipq60xx.mk

@@ -38,6 +38,33 @@ define Device/edgecore_eap101
 endef
 TARGET_DEVICES += edgecore_eap101
 
+define Device/indio_um-310ax-v1
+  DEVICE_TITLE := Indio UM-310AX V1
+  DEVICE_DTS := qcom-ipq6018-indio-um-310ax-v1
+  DEVICE_DTS_CONFIG := config@cp03-c1
+  SUPPORTED_DEVICES := indio,um-310ax-v1
+  DEVICE_PACKAGES := ath11k-wifi-indio-um-310ax-v1 uboot-env
+endef
+TARGET_DEVICES += indio_um-310ax-v1
+
+define Device/indio_um-510axp-v1
+  DEVICE_TITLE := Indio UM-510AXP V1
+  DEVICE_DTS := qcom-ipq6018-indio-um-510axp-v1
+  DEVICE_DTS_CONFIG := config@cp03-c1
+  SUPPORTED_DEVICES := indio,um-510axp-v1
+  DEVICE_PACKAGES := ath11k-wifi-indio-um-510axp-v1 uboot-env
+endef
+TARGET_DEVICES += indio_um-510axp-v1
+
+define Device/indio_um-510axm-v1
+  DEVICE_TITLE := Indio UM-510AXM V1
+  DEVICE_DTS := qcom-ipq6018-indio-um-510axm-v1
+  DEVICE_DTS_CONFIG := config@cp03-c1
+  SUPPORTED_DEVICES := indio,um-510axm-v1
+  DEVICE_PACKAGES := ath11k-wifi-indio-um-510axm-v1 uboot-env
+endef
+TARGET_DEVICES += indio_um-510axm-v1
+
 define Device/wallys_dr6018
   DEVICE_TITLE := Wallys DR6018
   DEVICE_DTS := qcom-ipq6018-wallys-dr6018

feeds/wifi-ax/ath11k-wifi/Makefile

@@ -36,6 +36,9 @@ ALLWIFIBOARDS:= \
 	sercomm-wallaby \
 	edgecore-eap102 \
 	edgecore-eap104 \
+	indio-um-310ax-v1 \
+	indio-um-510axp-v1 \
+	indio-um-510axm-v1 \
 	plasmacloud-pax1800 \
 	wallys-dr6018 \
 	wallys-dr6018-v4 \
@@ -240,6 +243,9 @@ $(eval $(call generate-ath11k-wifi-package,wallys-dr6018-v4,Wallys DR6018 V4))
 $(eval $(call generate-ath11k-wifi-package,edgecore-eap101,EdgeCore EAP101))
 $(eval $(call generate-ath11k-wifi-package,edgecore-eap102,Edgecore EAP102))
 $(eval $(call generate-ath11k-wifi-package,edgecore-eap104,Edgecore EAP104))
+$(eval $(call generate-ath11k-wifi-package,indio-um-310ax-v1,Indio UM-310AX V1))
+$(eval $(call generate-ath11k-wifi-package,indio-um-510axp-v1,Indio UM-510AXP V1))
+$(eval $(call generate-ath11k-wifi-package,indio-um-510axm-v1,Indio UM-510AXM V1))
 $(eval $(call generate-ath11k-wifi-package,tplink-ex227,TP-Link EX227))
 $(eval $(call generate-ath11k-wifi-package,tplink-ex447,TP-Link EX447))
 $(eval $(call generate-ath11k-wifi-package,yuncore-ax840,YunCore AX840))

profiles/indio_um-310ax-v1.yml

@@ -0,0 +1,12 @@
+---
+profile: indio_um-310ax-v1 
+target: ipq807x
+subtarget: ipq60xx
+description: Build image for the Indio UM-310AX V1 
+image: bin/targets/ipq807x/ipq60xx/openwrt-ipq807x-indio-um-310ax-v1-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x
+include:
+  - wifi-ax
+  - ucentral-ap

profiles/indio_um-510axm-v1.yml

@@ -0,0 +1,12 @@
+---
+profile: indio_um-510axm-v1 
+target: ipq807x
+subtarget: ipq60xx
+description: Build image for the Indio UM-510AXM V1 
+image: bin/targets/ipq807x/ipq60xx/openwrt-ipq807x-indio-um-510axm-v1-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x
+include:
+  - wifi-ax
+  - ucentral-ap

profiles/indio_um-510axp-v1.yml

@@ -0,0 +1,12 @@
+---
+profile: indio_um-510axp-v1 
+target: ipq807x
+subtarget: ipq60xx
+description: Build image for the Indio UM-510AXP V1 
+image: bin/targets/ipq807x/ipq60xx/openwrt-ipq807x-indio-um-510axp-v1-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x
+include:
+  - wifi-ax
+  - ucentral-ap