ipq807x: add initial support for MUXI AP3220L

Hardware:
* SoC: Qcom IPQ5018
* RAM: 512MB
* Flash: 4MB Nor + 128MB Nand
* Ethernet: 2x GbE
* WLAN: 2x2 2.4GHz 574Mbps(builtin) + 2x2 5GHz 2400Mbps(qcn6122)
* BT: BT5.1(builtin) / nrf52840(option)
* LEDS: 1x power, 1x 2G, 1x 5G
* Buttons: 1x reset
* USB: 1x 2.0(Type-A)
* Power: DC 12V/2A, PoE 48V/0.6A
* UART: 1x RJ45

Flash instruction under U-Boot:
tftpboot 0x44000000 openwrt-ipq807x-muxi_ap3220l-squashfs-nand-factory.bin
imxtract 0x44000000 ubi
flash rootfs
reset

Signed-off-by: angliu-muxi <ang.liu@muxi-connect.com>

feeds/ipq807x/ipq807x/base-files/etc/board.d/01_leds

@@ -50,6 +50,10 @@ glinet,ax1800|\
 glinet,axt1800)
 	ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0" "tx rx link"
 	;;
+muxi,ap3220l)
+        ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wifi2" "phy0tpt"
+        ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wifi5" "phy1tpt"
+	;;
 esac
 
 board_config_flush

feeds/ipq807x/ipq807x/base-files/etc/board.d/02_network

@@ -55,7 +55,8 @@ qcom_setup_interfaces()
 	liteon,wpx8324|\
 	wallys,dr6018|\
 	cig,wf188n|\
-	cig,wf196)
+	cig,wf196|\
+	muxi,ap3220l)
 		ucidef_set_interface_lan "eth1"
 		ucidef_set_interface_wan "eth0"
 		;;
@@ -123,6 +124,14 @@ qcom_setup_macs()
 		wan_mac=$(cat /sys/class/net/eth1/address)
 		lan_mac=$(macaddr_add "$wan_mac" 1)
 		;;
+	muxi,ap3220l)
+		wan_mac=$(mtd_get_mac_binary 0:Product_Info 0x5b)
+		lan_mac=$(macaddr_add "$wan_mac" 1)
+		ucidef_set_network_device_mac eth0 $wan_mac
+		ucidef_set_network_device_mac eth1 $lan_mac
+		ip link set eth0 address $wan_mac
+		ip link set eth1 address $lan_mac
+		;;
 	*)
 		wan_mac=$(cat /sys/class/net/eth0/address)
 		lan_mac=$(macaddr_add "$wan_mac" 1)

feeds/ipq807x/ipq807x/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -128,6 +128,7 @@ ath11k/IPQ5018/hw1.0/caldata.bin)
 	edgecore,eap104|\
 	liteon,wpx8324|\
 	motorola,q14|\
+	muxi,ap3220l|\
 	qcom,ipq5018-mp03.1)
                 caldata_extract "0:ART" 0x1000 0x20000  
 		;;
@@ -147,6 +148,9 @@ ath11k/qcn6122/hw1.0/caldata_2.bin)
 	liteon,wpx8324)
                 caldata_extract "0:ART" 0x4c000 0x20000  
 		;;
+	muxi,ap3220l)
+		caldata_extract "0:ART" 0x26800 0x20000
+		;;
 	esac
 	;;
 ath11k/QCN9074/hw1.0/caldata_1.bin)

feeds/ipq807x/ipq807x/base-files/lib/upgrade/platform.sh

@@ -90,12 +90,14 @@ platform_check_image() {
 	hfcl,ion4x|\
 	hfcl,ion4x_2|\
 	hfcl,ion4xe|\
+	muxi,ap3220l|\
 	plasmacloud,pax1800-v1|\
 	plasmacloud,pax1800-v2|\
 	tplink,ex227|\
 	tplink,ex447|\
 	yuncore,ax840|\
 	motorola,q14|\
+	muxi,ap3220l|\
 	qcom,ipq6018-cp01|\
 	qcom,ipq807x-hk01|\
 	qcom,ipq807x-hk14|\

feeds/ipq807x/ipq807x/files/arch/arm/boot/dts/qcom-ipq5018-muxi-ap3220l.dts

@@ -0,0 +1,23 @@
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "../../../arm64/boot/dts/qcom/qcom-ipq5018-muxi-ap3220l.dts"
+
+/ {
+	pmuv8: pmu {
+		compatible = "arm,cortex-a7-pmu";
+	};
+};

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-muxi-ap3220l.dts

@@ -0,0 +1,891 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "qcom-ipq5018.dtsi"
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "MUXI AP3220L";
+	compatible = "muxi,ap3220l", "qcom,ipq5018-mp03.5-c1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+	#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	#endif
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*                   256 MB Profile
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |           8MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x40800000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D100000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D300000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4E400000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4F300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4F400000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x4500000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x1400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xD00000>;
+		};
+
+		m3_dump: m3_dump@4D100000 {
+			no-map;
+			reg = <0x0 0x4D100000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E200000 {
+			no-map;
+			reg = <0x0 0x4E200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E300000 {
+			no-map;
+			reg = <0x0 0x4E300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E400000 {
+			no-map;
+			reg = <0x0 0x4E400000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4F300000 {
+			no-map;
+			reg = <0x0 0x4F300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F400000 {
+			no-map;
+			reg = <0x0 0x4F400000 0x0 0x100000>;
+		};
+	#else
+	/*                 512MB/1GB Profiles
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x41000000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          14MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  Caldb   |  0x4D400000  |           2MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D600000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E600000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E700000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  Caldb   |  0x4E800000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4ED00000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4FD00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4FE00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  Caldb   |  0x4FF00000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x5400000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 01400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xE00000>;
+		};
+
+		m3_dump: m3_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0x100000>;
+		};
+
+		q6_caldb_region: q6_caldb_region@4D400000 {
+			no-map;
+			reg = <0x0 0x4D400000 0x0 0x200000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D600000 {
+			no-map;
+			reg = <0x0 0x4D600000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E600000 {
+			no-map;
+			reg = <0x0 0x4E600000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E700000 {
+			no-map;
+			reg = <0x0 0x4E700000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_1: q6_qcn6122_caldb_1@4E800000 {
+			no-map;
+			reg = <0x0 0x4E800000 0x0 0x500000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E900000 {
+			no-map;
+			reg = <0x0 0x4ED00000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4FD00000 {
+			no-map;
+			reg = <0x0 0x4FD00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4FE00000 {
+			no-map;
+			reg = <0x0 0x4FE00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_2: q6_qcn6122_caldb_2@4FF00000 {
+			no-map;
+			reg = <0x0 0x4FF00000 0x0 0x500000>;
+		};
+
+	#endif
+	};
+
+	soc {
+
+		blsp1_uart1: serial@78af000 {
+			pinctrl-0 = <&blsp0_uart_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins &phy_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+
+			ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x2>;
+			ess-switch@0x39c00000 {
+				compatible = "qcom,ess-switch-ipq50xx";
+				device_id = <0>;
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+					};
+					port@1 {
+						port_id = <2>;
+						forced-speed = <1000>;
+						forced-duplex = <1>;
+					};
+				};
+				/*
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+				*/
+			};
+			ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x27>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <1>;
+					};
+					port@2 {
+						port_id = <3>;
+						phy_address = <2>;
+					};
+					port@3 {
+						port_id = <4>;
+						phy_address = <3>;
+					};
+				};
+			};
+		};
+
+		ess-uniphy@98000 {
+			status = "disabled";
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <3>;
+			mdio-bus = <&mdio1>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		qcom,test@0 {
+			status = "ok";
+		};
+
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+};
+
+&tlmm {
+	//pinctrl-0 = <&phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio23", "gpio25";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+				pins = "gpio9";
+				function = "qspi_clk";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_cs {
+				pins = "gpio8";
+				function = "qspi_cs";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_0 {
+				pins = "gpio7";
+				function = "qspi0";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_1 {
+				pins = "gpio6";
+				function = "qspi1";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_2 {
+				pins = "gpio5";
+				function = "qspi2";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_3 {
+				pins = "gpio4";
+				function = "qspi3";
+				drive-strength = <8>;
+				bias-disable;
+			};
+	};
+
+	phy_pins: phy_pins {
+		phy_intr {
+			pins = "gpio29";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+			bias-disable;
+		};
+		phy_reset {
+			pins = "gpio39";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			output-low;
+		};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			//pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button {
+			pins = "gpio32";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	led_pins: led_pins {
+		led_pwr {
+			pins = "gpio26";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_2g {
+			pins = "gpio31";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_5g {
+			pins = "gpio33";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+};
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "reset_button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+			led_power: led_pwr {
+				label = "green:led_pwr";
+				gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+				default-state = "on";
+				linux,default-trigger = "led_pwr";
+			};
+
+			led_2g {
+				label = "green:wifi2";
+				gpio = <&tlmm 33 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+
+			led_5g {
+				label = "green:wifi5";
+				gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+	};
+};
+
+&usb3 {
+	status = "ok";
+	device-power-gpio = <&tlmm 30 1>;
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	status = "disabled";
+	perst-gpio = <&tlmm 18 1>;
+};
+
+&pcie_x2 {
+	status = "disabled";
+	perst-gpio = <&tlmm 15 1>;
+};
+
+&dwc_0 {
+	/delete-property/ #phy-cells;
+	/delete-property/ phys;
+	/delete-property/ phy-names;
+};
+
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&pcie_x1phy {
+	status = "disabled";
+};
+
+&pcie_x2phy {
+	status = "disabled";
+};
+
+&pcie_x1_rp {
+        status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+        status = "disabled";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+
+	};
+};
+
+&qfprom {
+	status = "ok";
+};
+
+&tsens {
+	status = "ok";
+};
+
+&qcom_q6v5_wcss {
+	qcom,multipd_arch;
+	memory-region = <&q6_mem_regions>;
+	qcom,share_bootargs;
+	qcom,bootargs_smem = <507>;
+	boot-args = <0x2 0x4 0x2 0xF 0x0 0x0>;
+
+	/* IPQ5018 */
+	q6v5_wcss_userpd1 {
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+			<&wcss_smp2p_in 9 0>,
+			<&wcss_smp2p_in 12 0>,
+			<&wcss_smp2p_in 11 0>;
+		interrupt-names ="fatal",
+			"ready",
+			"spawn_ack",
+			"stop-ack";
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+			<&wcss_smp2p_out 9>,
+			<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+			"stop",
+			"spawn";
+		qca,asid = <1>;
+		qca,auto-restart;
+		qca,int_radio;
+		#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>;
+		#else
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>, <&q6_caldb_region>;
+		#endif
+	};
+
+	/* QCN6122 6G */
+	q6v5_wcss_userpd2 {
+		m3_firmware = "qcn6122/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 16 0>,
+			<&wcss_smp2p_in 17 0>,
+			<&wcss_smp2p_in 20 0>,
+			<&wcss_smp2p_in 19 0>;
+		interrupt-names ="fatal",
+			"ready",
+			"spawn_ack",
+			"stop-ack";
+		qcom,smem-states = <&wcss_smp2p_out 16>,
+			<&wcss_smp2p_out 17>,
+			<&wcss_smp2p_out 18>;
+		qcom,smem-state-names = "shutdown",
+			"stop",
+			"spawn";
+		qca,asid = <2>;
+		qca,auto-restart;
+		#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>;
+		#else
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>, <&q6_qcn6122_caldb_1>;
+		#endif
+	};
+
+	/* QCN6122 5G */
+	q6v5_wcss_userpd3 {
+		m3_firmware = "qcn6122/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 24 0>,
+			<&wcss_smp2p_in 25 0>,
+			<&wcss_smp2p_in 28 0>,
+			<&wcss_smp2p_in 27 0>;
+		interrupt-names ="fatal",
+			"ready",
+			"spawn_ack",
+			"stop-ack";
+		qcom,smem-states = <&wcss_smp2p_out 24>,
+			<&wcss_smp2p_out 25>,
+			<&wcss_smp2p_out 26>;
+		qcom,smem-state-names = "shutdown",
+			"stop",
+			"spawn";
+		qca,asid = <3>;
+		qca,auto-restart;
+		#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>;
+		#else
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>, <&q6_qcn6122_caldb_2>;
+		#endif
+	};
+};
+
+&qgic_msi_0 {
+	status = "ok";
+};
+
+&qgic_msi_1 {
+	status = "ok";
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x24>;
+	qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
+#ifdef __CNSS2__
+	qcom,caldb-addr = <0x4D400000 0x4D400000 0 0 0>;
+#else
+	qcom,caldb-addr = <0x4D400000>;
+	m3-dump-addr = <0x4D200000>;
+#endif
+	qcom,caldb-size = <0x200000>;
+	status = "ok";
+};
+
+&wifi1 {
+	/* QCN6122 6G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x60>;
+	qcom,bdf-addr = <0x4D600000 0x4D600000 0x4D300000 0x0 0x0>;
+#ifdef __CNSS2__
+	qcom,caldb-addr = <0x4E800000 0x4E800000 0 0 0>;
+#else
+	qcom,caldb-addr = <0x4E800000>;
+	m3-dump-addr = <0x4E600000>;
+#endif
+	qcom,caldb-size = <0x500000>;
+	status = "disabled";
+};
+
+&wifi2 {
+	/* QCN6122 5G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x60>;
+	qcom,bdf-addr = <0x4ED00000 0x4ED00000 0x4E400000 0x0 0x0>;
+#ifdef __CNSS2__
+	qcom,caldb-addr = <0x4FF00000 0x4FF00000 0 0 0>;
+#else
+	qcom,caldb-addr = <0x4FF00000>;
+	m3-dump-addr = <0x4FD00000>;
+#endif
+	qcom,caldb-size = <0x500000>;
+	status = "ok";
+};

feeds/ipq807x/ipq807x/image/ipq50xx.mk

@@ -27,6 +27,15 @@ define Device/liteon_wpx8324
 endef
 TARGET_DEVICES += liteon_wpx8324
 
+define Device/muxi_ap3220l
+  DEVICE_TITLE := MUXI AP3220L
+  DEVICE_DTS := qcom-ipq5018-muxi-ap3220l
+  SUPPORTED_DEVICES := muxi,ap3220l
+  DEVICE_PACKAGES := ath11k-wifi-muxi-ap3220l ath11k-firmware-ipq50xx-spruce ath11k-firmware-qcn6122
+  DEVICE_DTS_CONFIG := config@mp03.5-c1
+endef
+TARGET_DEVICES += muxi_ap3220l
+
 define Device/motorola_q14
   DEVICE_TITLE := Motorola Q14
   DEVICE_DTS := qcom-ipq5018-q14

feeds/wifi-ax/ath11k-wifi/Makefile

@@ -40,6 +40,7 @@ ALLWIFIBOARDS:= \
 	indio-um-310ax-v1 \
 	indio-um-510axp-v1 \
 	indio-um-510axm-v1 \
+	muxi-ap3220l \
 	plasmacloud-pax1800 \
 	wallys-dr6018 \
 	wallys-dr6018-v4 \
@@ -252,6 +253,7 @@ $(eval $(call generate-ath11k-wifi-package,tplink-ex227,TP-Link EX227))
 $(eval $(call generate-ath11k-wifi-package,tplink-ex447,TP-Link EX447))
 $(eval $(call generate-ath11k-wifi-package,yuncore-ax840,YunCore AX840))
 $(eval $(call generate-ath11k-wifi-package,meshpp-s618,Mesh++ S618))
+$(eval $(call generate-ath11k-wifi-package,muxi-ap3220l,MUXI AP3220L))
 
 $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
 $(eval $(call BuildPackage,ath11k-wifi-qcom-ipq5018))