ipq60xx: Support EMPLUS WAP386V2 model

Device specifications:
======================

SoC: Qualcomm IPQ6018
RAM: 1 x 1G DDR4 RAM
Flash: NAND 128MB
Radio: 2T2R@2.4GHz, 2T2R@5GHz
Ethernet: 1 x 1GbE PHY
Reset Button: 1
Power Source: AC, Standard PoE 802.3af/at
LED Indicator: 4 x Single-color LED indicator (GPIO Control)

Signed-off-by: Jesse Wu <Jesse.Wu@emplustech.com>

feeds/ipq807x_v5.4/ath11k-wifi/Makefile

@@ -41,6 +41,7 @@ ALLWIFIBOARDS:= \
 	edgecore-oap102 \
 	edgecore-oap103 \
 	edgecore-eap104 \
+	emplus-wap386v2 \
 	liteon-wpx8324 \
 	indio-um-310ax-v1 \
 	indio-um-510axp-v1 \
@@ -404,6 +405,7 @@ $(eval $(call generate-ath11k-wifi-package,edgecore-eap102,Edgecore EAP102))
 $(eval $(call generate-ath11k-wifi-package,edgecore-oap102,Edgecore OAP102))
 $(eval $(call generate-ath11k-wifi-package,edgecore-oap103,Edgecore OAP103))
 $(eval $(call generate-ath11k-wifi-package,edgecore-eap104,Edgecore EAP104))
+$(eval $(call generate-ath11k-wifi-package,emplus-wap386v2,Emplus WAP386 V2))
 $(eval $(call generate-ath11k-wifi-package,liteon-wpx8324,Liteon WPX8324))
 $(eval $(call generate-ath11k-wifi-package,indio-um-310ax-v1,Indio UM-310AX V1))
 $(eval $(call generate-ath11k-wifi-package,indio-um-510axp-v1,Indio UM-510AXP V1))

feeds/ipq807x_v5.4/ipq60xx/base-files/etc/board.d/01_leds

@@ -26,6 +26,12 @@ edgecore,eap101)
 	ucidef_set_led_netdev "poe" "poe" "green:wan" "eth0"
         ucidef_set_led_default "power" "POWER" "green:led_pwr" "on"
 	;;
+emplus,wap386v2)
+	ucidef_set_led_default "power" "POWER" "red:power" "on"
+	ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0" "tx rx link"
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "blue:wifi2" "phy1tpt"
+	ucidef_set_led_wlan "wlan5g" "WLAN5G" "blue:wifi5" "phy0tpt"
+	;;
 hfcl,ion4xi|\
 hfcl,ion4x|\
 hfcl,ion4x_2|\

feeds/ipq807x_v5.4/ipq60xx/base-files/etc/board.d/02_network

@@ -34,10 +34,10 @@ qcom_setup_interfaces()
 		ucidef_set_interface_lan "eth1"
 		ucidef_set_interface_wan "eth0"
 		;;
-       cig,wf660a)
+	cig,wf660a|\
+	emplus,wap386v2)
 		ucidef_set_interface_wan "eth0"		
 		;;
-
 	yuncore,fap650)
 		ucidef_set_interface_lan "eth3 eth2 eth1 eth0"
 		ucidef_set_interface_wan "eth4"
@@ -76,6 +76,9 @@ qcom_setup_macs()
 		ucidef_set_network_device_mac eth0 $wan_mac
 		ip link set eth0 address $wan_mac
 		;;
+	emplus,wap386v2)
+		wan_mac=$(cat /sys/class/net/eth0/address)
+		;;
 	yuncore,ax840)
 		wan_mac=$(cat /sys/class/net/eth1/address)
 		lan_mac=$(macaddr_add "$wan_mac" 1)

feeds/ipq807x_v5.4/ipq60xx/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -76,6 +76,7 @@ case "$FIRMWARE" in
 	cig,wf188n|\
 	cig,wf660a|\
 	edgecore,eap101|\
+	emplus,wap386v2|\
 	hfcl,ion4xi|\
 	hfcl,ion4x|\
 	hfcl,ion4x_2|\
@@ -109,7 +110,8 @@ ath11k-macs)
 	edgecore,eap101)
 		ath11k_generate_macs_eap101
 		;;
-	cig,wf188n)
+	cig,wf188n|\
+	emplus,wap386v2)
 		ath11k_generate_macs
 		;;
 	cig,wf660a)

feeds/ipq807x_v5.4/ipq60xx/base-files/lib/upgrade/platform.sh

@@ -122,6 +122,7 @@ platform_check_image() {
 	wallys,dr6018|\
 	wallys,dr6018-v4|\
 	edgecore,eap101|\
+	emplus,wap386v2|\
 	hfcl,ion4xi|\
 	hfcl,ion4x|\
 	hfcl,ion4x_2|\
@@ -145,7 +146,8 @@ platform_do_upgrade() {
 	cig,wf660a)
 		spi_nor_emmc_do_upgrade_bootconfig $1
 		;;
-	cig,wf188n)
+	cig,wf188n|\
+	emplus,wap386v2)
 		[ -f /proc/boot_info/rootfs/upgradepartition ] && {
 			CI_UBIPART="$(cat /proc/boot_info/rootfs/upgradepartition)"
 			CI_BOOTCFG=1

feeds/ipq807x_v5.4/ipq60xx/files/arch/arm64/boot/dts/qcom/qcom-ipq6018-emplus-wap386v2.dts

@@ -0,0 +1,356 @@
+/*
+ * Copyright (c) 2019-2021, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+#include "ipq6018-cpr-regulator.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Emplus WAP386 v2";
+	compatible = "emplus,wap386v2", "qcom,ipq6018-cp03", "qcom,ipq6018";
+
+	aliases {
+		/*
+		 * Aliases as required by u-boot
+		 * to patch MAC addresses
+		 */
+		ethernet0 = "/soc/dp1";
+
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	};
+
+	/*
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  |         139MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | TZ App |  0x49B00000  |           6MB           |
+	 * +--------+--------------+-------------------------+
+	 *
+	 * From the available 145 MB for Linux in the first 256 MB,
+	 * we are reserving 6 MB for TZAPP.
+	 *
+	 * Refer arch/arm64/boot/dts/qcom/qcom-ipq6018-memory.dtsi
+	 * for memory layout.
+	 */
+
+/* TZAPP is enabled only in default memory profile */
+#if !defined(__IPQ_MEM_PROFILE_256_MB__) && !defined(__IPQ_MEM_PROFILE_512_MB__)
+	reserved-memory {
+		tzapp:tzapp@49B00000 {	/* TZAPPS */
+			no-map;
+			reg = <0x0 0x49B00000 0x0 0x00600000>;
+		};
+	};
+#endif
+};
+
+&tlmm {
+	gpio-reserved-ranges = <20 1>;
+
+	uart_pins: uart_pins {
+		mux {
+			pins = "gpio44", "gpio45";
+			function = "blsp2_uart";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	spi_0_pins: spi_0_pins {
+		mux {
+			pins = "gpio38", "gpio39", "gpio40", "gpio41";
+			function = "blsp0_spi";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button {
+			pins = "gpio9";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio64";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		mux_1 {
+			pins = "gpio65";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		mux_2 {
+			pins = "gpio75";
+			function = "gpio";
+			bias-pull-up;
+		};
+	};
+
+	leds_pins: leds_pins {
+		led_5g {
+			pins = "gpio31";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_2g {
+			pins = "gpio30";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+};
+
+&soc {
+	mdio@90000 {
+		pinctrl-0 = <&mdio_pins>;
+		pinctrl-names = "default";
+		phy-reset-gpio = <&tlmm 75 0>;
+		status = "ok";
+		phy0: ethernet-phy@0 {
+			reg = <3>;
+		};
+		phy1: ethernet-phy@1 {
+			reg = <4>;
+		};
+	};
+
+	ess-switch@3a000000 {
+		switch_cpu_bmp = <0x1>;  /* cpu port bitmap */
+		switch_lan_bmp = <0x08>; /* lan port bitmap */
+		switch_wan_bmp = <0x10>; /* wan port bitmap */
+		switch_inner_bmp = <0xc0>; /*inner port bitmap*/
+		switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/
+		switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
+		switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
+		qcom,port_phyinfo {
+			port@0 {
+				port_id = <2>;
+				phy_address = <3>;
+			};
+			port@1 {
+				port_id = <3>;
+				phy_address = <4>;
+			};
+		};
+	};
+
+	dp1 {
+		device_type = "network";
+		compatible = "qcom,nss-dp";
+		qcom,id = <3>;
+		reg = <0x3a001400 0x200>;
+		qcom,mactype = <0>;
+		local-mac-address = [000000000000];
+		qcom,link-poll = <1>;
+		qcom,phy-mdio-addr = <4>;
+		phy-mode = "sgmii";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button@9 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led_power: led@28 {
+			label = "red:power";
+			gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "wap386v2:red:power";
+			default-state = "on";
+		};
+		led@29 {
+			label = "blue:wan";
+			gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "wap386v2:blue:eth";
+			default-state = "on";
+		};
+		led@30 {
+			label = "blue:wifi2";
+			gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "wap386v2:blue:2g";
+			default-state = "on";
+		};
+		led@31 {
+			label = "blue:wifi5";
+			gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "wap386v2:blue:5g";
+			default-state = "on";
+		};
+	};
+};
+
+&blsp1_uart3 {
+	pinctrl-0 = <&uart_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&spi_0 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-select = <0>;
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		compatible = "n25q128a11";
+		linux,modalias = "m25p80", "n25q128a11";
+		spi-max-frequency = <50000000>;
+		use-default-sizes;
+	};
+};
+
+&wifi0 {
+	qcom,board_id = <0x30>;
+};
+
+&pcie_phy {
+	status = "ok";
+};
+
+&pcie0 {
+#if defined(__CNSS2__)
+	status = "ok";
+#endif
+};
+
+&qpic_bam {
+	status = "ok";
+};
+
+&qpic_nand {
+	status = "ok";
+
+	nand@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+	};
+};
+
+&ssphy_0 {
+	status = "ok";
+};
+
+&nss_crypto {
+	status = "ok";
+};
+
+&CPU0 {
+	operating-points = <
+		/* kHz   uV (fixed) */
+		864000   1100000
+		1056000  1100000
+		1320000  1100000
+		1440000  1100000
+		1608000  1100000
+		1800000  1100000
+	>;
+	clock-latency = <200000>;
+};
+
+&CPU1 {
+	operating-points = <
+		/* kHz   uV (fixed) */
+		864000   1100000
+		1056000  1100000
+		1320000  1100000
+		1440000  1100000
+		1608000  1100000
+		1800000  1100000
+	>;
+	clock-latency = <200000>;
+};
+
+&CPU2 {
+	operating-points = <
+		/* kHz   uV (fixed) */
+		864000   1100000
+		1056000  1100000
+		1320000  1100000
+		1440000  1100000
+		1608000  1100000
+		1800000  1100000
+	>;
+	clock-latency = <200000>;
+};
+
+&CPU3 {
+	operating-points = <
+		/* kHz   uV (fixed) */
+		864000   1100000
+		1056000  1100000
+		1320000  1100000
+		1440000  1100000
+		1608000  1100000
+		1800000  1100000
+	>;
+	clock-latency = <200000>;
+};
+
+&rpm_glink {
+	status = "disabled";
+};

feeds/ipq807x_v5.4/ipq60xx/image/ipq60xx.mk

@@ -76,6 +76,15 @@ define Device/edgecore_eap101
 endef
 TARGET_DEVICES += edgecore_eap101
 
+define Device/emplus_wap386v2
+  DEVICE_TITLE := Emplus WAP386v2
+  DEVICE_DTS := qcom-ipq6018-emplus-wap386v2
+  DEVICE_DTS_CONFIG := config@cp03-c1
+  SUPPORTED_DEVICES := emplus,wap386v2
+  DEVICE_PACKAGES := ath11k-wifi-qcom-ipq6018 uboot-env
+endef
+TARGET_DEVICES += emplus_wap386v2
+
 define Device/indio_um-310ax-v1
   DEVICE_TITLE := Indio UM-310AX V1
   DEVICE_DTS := qcom-ipq6018-indio-um-310ax-v1

feeds/tip/certificates/files/usr/bin/mount_certs

@@ -88,6 +88,7 @@ cig,wf189h|\
 cig,wf186h|\
 cig,wf196|\
 cig,wf188n|\
+emplus,wap386v2|\
 yuncore,ax840|\
 yuncore,fap655)
 	PART_NAME=rootfs_1

profiles/emplus_wap386v2.yml

@@ -0,0 +1,24 @@
+---
+profile: emplus_wap386v2
+target: ipq60xx
+subtarget: generic
+description: Build image for the EMPLUS WAP386V2
+image: bin/targets/ipq60xx/generic/openwrt-ipq60xx-emplus_wap386v2-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x_v5.4
+include:
+  - ucentral-ap
+packages:
+  - ipq60xx
+  - iperf3
+diffconfig: |
+  CONFIG_BUSYBOX_CUSTOM=y
+  CONFIG_BUSYBOX_CONFIG_TFTP=y
+  CONFIG_BUSYBOX_CONFIG_FEATURE_TFTP_PROGRESS_BAR=y
+  CONFIG_BUSYBOX_CONFIG_FEATURE_TFTP_HPA_COMPAT=y
+  CONFIG_BUSYBOX_CONFIG_FEATURE_TFTP_GET=y
+  CONFIG_BUSYBOX_CONFIG_FEATURE_TFTP_PUT=y
+  CONFIG_BUSYBOX_CONFIG_LSOF=y
+  CONFIG_BUSYBOX_CONFIG_MPSTAT=y
+  CONFIG_BUSYBOX_CONFIG_PSTREE=y