WIFI-14849 When device is booting,it causes lan/wan ports bridge together

Signed-off-by: jackcybertan <jack.tsai@cybertan.com.tw>

feeds/ipq807x_v5.4/ipq50xx/Makefile

@@ -27,6 +27,7 @@ DEFAULT_PACKAGES += kmod-qca-nss-dp kmod-qca-ssdk swconfig \
 	kmod-ath11k-ahb  ath11k-firmware-ipq5018 \
 	kmod-gpio-button-hotplug iwinfo \
 	qca-ssdk-shell kmod-bootconfig \
-	uboot-envtools -procd-ujail
+	uboot-envtools -procd-ujail \
+	kmod-mdio-qca
 
 $(eval $(call BuildTarget))

feeds/ipq807x_v5.4/ipq50xx/config-5.4

@@ -635,7 +635,7 @@ CONFIG_MDIO_BITBANG=y
 CONFIG_MDIO_BOARDINFO=y
 # CONFIG_MDIO_BUS_MUX_MULTIPLEXER is not set
 CONFIG_MDIO_GPIO=y
-CONFIG_MDIO_QCA=y
+CONFIG_MDIO_QCA=m
 # CONFIG_MDM_GCC_9615 is not set
 # CONFIG_MDM_LCC_9615 is not set
 # CONFIG_MEMORY_HOTPLUG is not set

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-eww631-b1.dts

@@ -391,8 +391,8 @@
 				mdio-bus = <&mdio1>;
 				reset_gpio = <&tlmm 0x26 0>;
 				switch_cpu_bmp = <0x40>;  /* cpu port bitmap (Port 6 GMAC) */
-				switch_lan_bmp = <0x3c>; /* lan port bitmap */
-				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				switch_lan_bmp = <0x1c>; /* lan port bitmap */
+				switch_wan_bmp = <0x20>;  /* wan port bitmap */
 				qca,ar8327-initvals = <
 						0x00004 0x7600000   /* PAD0_MODE */
 						0x00008 0x1000000   /* PAD5_MODE */

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-rap630w-311g.dts

@@ -393,8 +393,8 @@
 				mdio-bus = <&mdio1>;
 				reset_gpio = <&tlmm 0x26 0>;
 				switch_cpu_bmp = <0x40>;  /* cpu port bitmap (Port 6 GMAC) */
-				switch_lan_bmp = <0x3c>; /* lan port bitmap */
-				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				switch_lan_bmp = <0x1c>; /* lan port bitmap */
+				switch_wan_bmp = <0x20>;  /* wan port bitmap */
 				qca,ar8327-initvals = <
 						0x00004 0x7600000   /* PAD0_MODE */
 						0x00008 0x1000000   /* PAD5_MODE */

feeds/ipq807x_v5.4/ipq50xx/modules.mk

@@ -242,3 +242,17 @@ define KernelPackage/bootconfig/description
 endef
 
 $(eval $(call KernelPackage,bootconfig))
+
+define KernelPackage/mdio-qca
+  SUBMENU:=$(NETWORK_DEVICES_MENU)
+  TITLE:=Model for MDIO to QCA PHY connection
+  KCONFIG:=CONFIG_MDIO_QCA
+  FILES:=$(LINUX_DIR)/drivers/net/phy/mdio-qca.ko
+  AUTOLOAD:=$(call AutoLoad,30,mdio-qca)
+endef
+
+define KernelPackage/mdio-qca/description
+ This driver supports the MDIO interface found in Qualcomm Atheros ipq Soc chip.
+endef
+
+$(eval $(call KernelPackage,mdio-qca))