hostapd: initialize ht/vht/he mode on channel switch by default while using hostapd_cli chan_switch command

fixed: WIFI-14859
Signed-off-by: Tanya Singh <tanya_singh@accton.com>

feeds/ipq807x_v5.4/ath11k-wifi/Makefile

@@ -50,7 +50,6 @@ ALLWIFIBOARDS:= \
 	indio-um-325ax-v2 \
 	indio-um-335ax \
 	indio-um-525axp \
-	indio-um-525axm \
 	muxi-ap3220l \
 	plasmacloud-pax1800 \
 	wallys-dr5018 \
@@ -448,7 +447,6 @@ $(eval $(call generate-ath11k-wifi-package,indio-um-510axm-v1,Indio UM-510AXM V1
 $(eval $(call generate-ath11k-wifi-package,indio-um-325ax-v2,Indio UM-325AX V2))
 $(eval $(call generate-ath11k-wifi-package,indio-um-335ax,Indio UM-335AX))
 $(eval $(call generate-ath11k-wifi-package,indio-um-525axp,Indio UM-525AXP))
-$(eval $(call generate-ath11k-wifi-package,indio-um-525axm,Indio UM-525AXM))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630c-311g,Sonicfi RAP630C 311G))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630w-311g,Sonicfi RAP630W 311G))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630w-312g,Sonicfi RAP630W 312G))

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/board.d/01_leds

@@ -18,7 +18,6 @@ edgecore,eap104)
 	;;
 indio,um-325ax-v2|\
 indio,um-335ax|\
-indio,um-525axm|\
 indio,um-525axp)
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "led_2g" "phy0tpt"
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "led_5g" "phy1tpt"

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/board.d/02_network

@@ -50,7 +50,6 @@ qcom_setup_interfaces()
 		;;
 	indio,um-325ax-v2|\
 	indio,um-335ax|\
-	indio,um-525axm|\
 	indio,um-525axp)
 		ucidef_set_interface_wan "eth1"
 		ucidef_set_interface_lan "eth0"

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -144,7 +144,6 @@ ath11k/IPQ5018/hw1.0/caldata.bin)
 	hfcl,ion4xi_w|\
 	indio,um-325ax-v2|\
 	indio,um-335ax|\
-	indio,um-525axm|\
 	indio,um-525axp|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
@@ -188,7 +187,6 @@ ath11k/qcn6122/hw1.0/caldata_1.bin)
 ath11k/qcn6122/hw1.0/caldata_2.bin)
 	case "$board" in
 	indio,um-325ax-v2|\
-	indio,um-525axm|\
 	indio,um-525axp|\
 	wallys,dr5018|\
 	edgecore,eap104|\
@@ -244,7 +242,6 @@ ath11k-macs)
 	edgecore,oap101e-6e|\
 	indio,um-325ax-v2|\
 	indio,um-525axp|\
-	indio,um-525axm|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
 	optimcloud,d50|\

feeds/ipq807x_v5.4/ipq50xx/base-files/lib/upgrade/platform.sh

@@ -84,7 +84,6 @@ platform_check_image() {
 	indio,um-325ax-v2|\
 	indio,um-335ax|\
 	indio,um-525axp|\
-	indio,um-525axm|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
 	optimcloud,d50|\
@@ -114,7 +113,6 @@ platform_do_upgrade() {
 	indio,um-325ax-v2|\
 	indio,um-335ax|\
 	indio,um-525axp|\
-	indio,um-525axm|\
 	edgecore,oap101|\
 	edgecore,oap101-6e|\
 	edgecore,oap101e|\

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-indio-um-525axm.dts

@@ -1,941 +0,0 @@
-/dts-v1/;
-/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
- *
- * Permission to use, copy, modify, and/or distribute this software for any
- * purpose with or without fee is hereby granted, provided that the above
- * copyright notice and this permission notice appear in all copies.
- *
- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
- * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
- * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
- * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
- * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
- * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
- */
-
-#include "ipq5018.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
-	#address-cells = <0x2>;
-	#size-cells = <0x2>;
-	model = "Indio UM-525AXM";
-	compatible = "indio,um-525axm", "qcom,ipq5018-mp03.5-c1", "qcom,ipq5018";
-	interrupt-parent = <&intc>;
-
-	aliases {
-		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
-		serial0 = &blsp1_uart1;
-		serial1 = &blsp1_uart2;
-		ethernet0 = "/soc/dp1";
-		ethernet1 = "/soc/dp2";
-                //led-failsafe = &led_red;
-                //led-running = &led_green;
-                //led-upgrade = &led_green;
-                //led-gateway = &led_blue;
-                //led-factory = &led_blue;
-	};
-
-	chosen {
-		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
-	#ifdef __IPQ_MEM_PROFILE_256_MB__
-		bootargs-append = " swiotlb=1";
-	#else
-		bootargs-append = " swiotlb=1 coherent_pool=2M";
-	#endif
-		stdout-path = "serial0";
-	};
-
-	reserved-memory {
-	#ifdef __IPQ_MEM_PROFILE_256_MB__
-	/*                   256 MB Profile
-	 * +==========+==============+=========================+
-	 * |          |              |                         |
-	 * |  Region  | Start Offset |          Size           |
-	 * |          |              |                         |
-	 * +----------+--------------+-------------------------+
-	 * |    NSS   |  0x40000000  |           8MB           |
-	 * +----------+--------------+-------------------------+
-	 * |   Linux  |  0x40800000  | Depends on total memory |
-	 * +----------+--------------+-------------------------+
-	 * |   uboot  |  0x4A600000  |           4MB           |
-	 * +----------+--------------+-------------------------+
-	 * |    SBL   |  0x4AA00000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * |   smem   |  0x4AB00000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * |    TZ    |  0x4AC00000  |           4MB           |
-	 * +----------+--------------+-------------------------+
-	 * |    Q6    |              |                         |
-	 * |   code/  |  0x4B000000  |          20MB           |
-	 * |   data   |              |                         |
-	 * +----------+--------------+-------------------------+
-	 * |  IPQ5018 |              |                         |
-	 * |   data   |  0x4C400000  |          13MB           |
-	 * +----------+--------------+-------------------------+
-	 * |  IPQ5018 |              |                         |
-	 * |  M3 Dump |  0x4D100000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * |  IPQ5018 |              |                         |
-	 * |   QDSS   |  0x4D200000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_1|              |                         |
-	 * |   data   |  0x4D300000  |          15MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_1|              |                         |
-	 * |  M3 Dump |  0x4E200000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_1|              |                         |
-	 * |   QDSS   |  0x4E300000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_2|              |                         |
-	 * |   data   |  0x4E400000  |          15MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_2|              |                         |
-	 * |  M3 Dump |  0x4F300000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_2|              |                         |
-	 * |   QDSS   |  0x4F400000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * |                                                   |
-	 * |            Rest of the memory for Linux           |
-	 * |                                                   |
-	 * +===================================================+
-	 */
-		q6_mem_regions: q6_mem_regions@4B000000 {
-			no-map;
-			reg = <0x0 0x4B000000 0x0 0x4500000>;
-		};
-
-		q6_code_data: q6_code_data@4B000000 {
-			no-map;
-			reg = <0x0 0x4B000000 0x0 0x1400000>;
-		};
-
-		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
-			no-map;
-			reg = <0x0 0x4C400000 0x0 0xD00000>;
-		};
-
-		m3_dump: m3_dump@4D100000 {
-			no-map;
-			reg = <0x0 0x4D100000 0x0 0x100000>;
-		};
-
-		q6_etr_region: q6_etr_dump@4D200000 {
-			no-map;
-			reg = <0x0 0x4D200000 0x0 0x100000>;
-		};
-
-		q6_qcn6122_data1: q6_qcn6122_data1@4D300000 {
-			no-map;
-			reg = <0x0 0x4D300000 0x0 0xF00000>;
-		};
-
-		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E200000 {
-			no-map;
-			reg = <0x0 0x4E200000 0x0 0x100000>;
-		};
-
-		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E300000 {
-			no-map;
-			reg = <0x0 0x4E300000 0x0 0x100000>;
-		};
-
-		q6_qcn6122_data2: q6_qcn6122_data2@4E400000 {
-			no-map;
-			reg = <0x0 0x4E400000 0x0 0xF00000>;
-		};
-
-		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4F300000 {
-			no-map;
-			reg = <0x0 0x4F300000 0x0 0x100000>;
-		};
-
-		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F400000 {
-			no-map;
-			reg = <0x0 0x4F400000 0x0 0x100000>;
-		};
-		
-	#else
-	/*                 512MB/1GB Profiles
-	 * +==========+==============+=========================+
-	 * |          |              |                         |
-	 * |  Region  | Start Offset |          Size           |
-	 * |          |              |                         |
-	 * +----------+--------------+-------------------------+
-	 * |    NSS   |  0x40000000  |          16MB           |
-	 * +----------+--------------+-------------------------+
-	 * |   Linux  |  0x41000000  | Depends on total memory |
-	 * +----------+--------------+-------------------------+
-	 * |   uboot  |  0x4A600000  |           4MB           |
-	 * +----------+--------------+-------------------------+
-	 * |    SBL   |  0x4AA00000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * |   smem   |  0x4AB00000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * |    TZ    |  0x4AC00000  |           4MB           |
-	 * +----------+--------------+-------------------------+
-	 * |    Q6    |              |                         |
-	 * |   code/  |  0x4B000000  |          20MB           |
-	 * |   data   |              |                         |
-	 * +----------+--------------+-------------------------+
-	 * |  IPQ5018 |              |                         |
-	 * |   data   |  0x4C400000  |          14MB           |
-	 * +----------+--------------+-------------------------+
-	 * |  IPQ5018 |              |                         |
-	 * |  M3 Dump |  0x4D200000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * |  IPQ5018 |              |                         |
-	 * |   QDSS   |  0x4D300000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * |  IPQ5018 |              |                         |
-	 * |  Caldb   |  0x4D400000  |           2MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_1|              |                         |
-	 * |   data   |  0x4D600000  |          16MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_1|              |                         |
-	 * |  M3 Dump |  0x4E600000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_1|              |                         |
-	 * |   QDSS   |  0x4E700000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_1|              |                         |
-	 * |  Caldb   |  0x4E800000  |           5MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_2|              |                         |
-	 * |   data   |  0x4ED00000  |          16MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_2|              |                         |
-	 * |  M3 Dump |  0x4FD00000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_2|              |                         |
-	 * |   QDSS   |  0x4FE00000  |           1MB           |
-	 * +----------+--------------+-------------------------+
-	 * | QCN6122_2|              |                         |
-	 * |  Caldb   |  0x4FF00000  |           5MB           |
-	 * +----------+--------------+-------------------------+
-	 * |                                                   |
-	 * |            Rest of the memory for Linux           |
-	 * |                                                   |
-	 * +===================================================+
-	 */
-		q6_mem_regions: q6_mem_regions@4B000000 {
-			no-map;
-			reg = <0x0 0x4B000000 0x0 0x5400000>;
-		};
-
-		q6_code_data: q6_code_data@4B000000 {
-			no-map;
-			reg = <0x0 0x4B000000 0x0 01400000>;
-		};
-
-		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
-			no-map;
-			reg = <0x0 0x4C400000 0x0 0xE00000>;
-		};
-
-		m3_dump: m3_dump@4D200000 {
-			no-map;
-			reg = <0x0 0x4D200000 0x0 0x100000>;
-		};
-
-		q6_etr_region: q6_etr_dump@4D300000 {
-			no-map;
-			reg = <0x0 0x4D300000 0x0 0x100000>;
-		};
-
-		q6_caldb_region: q6_caldb_region@4D400000 {
-			no-map;
-			reg = <0x0 0x4D400000 0x0 0x200000>;
-		};
-
-		q6_qcn6122_data1: q6_qcn6122_data1@4D600000 {
-			no-map;
-			reg = <0x0 0x4D600000 0x0 0x1000000>;
-		};
-
-		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E600000 {
-			no-map;
-			reg = <0x0 0x4E600000 0x0 0x100000>;
-		};
-
-		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E700000 {
-			no-map;
-			reg = <0x0 0x4E700000 0x0 0x100000>;
-		};
-
-		q6_qcn6122_caldb_1: q6_qcn6122_caldb_1@4E800000 {
-			no-map;
-			reg = <0x0 0x4E800000 0x0 0x500000>;
-		};
-
-		q6_qcn6122_data2: q6_qcn6122_data2@4E900000 {
-			no-map;
-			reg = <0x0 0x4ED00000 0x0 0x1000000>;
-		};
-
-		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4FD00000 {
-			no-map;
-			reg = <0x0 0x4FD00000 0x0 0x100000>;
-		};
-
-		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4FE00000 {
-			no-map;
-			reg = <0x0 0x4FE00000 0x0 0x100000>;
-		};
-
-		q6_qcn6122_caldb_2: q6_qcn6122_caldb_2@4FF00000 {
-			no-map;
-			reg = <0x0 0x4FF00000 0x0 0x500000>;
-		};
-
-	#endif
-	};
-
-	soc {
-		gpio-watchdog {
-			compatible = "linux,wdt-gpio";
-			gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
-			hw_algo = "toggle";
-			hw_margin_ms = <5000>;
-			always-running;
-		};
-
-		serial@78af000 {
-			status = "ok";
-		};
-
-		blsp1_uart2: serial@78b0000 {
-			pinctrl-0 = <&blsp1_uart_pins>;
-			pinctrl-names = "default";
-		};
-
-		qpic_bam: dma@7984000{
-			status = "ok";
-		};
-
-		nand: qpic-nand@79b0000 {
-			pinctrl-0 = <&qspi_nand_pins>;
-			pinctrl-names = "default";
-			status = "ok";
-		};
-
-		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
-			pinctrl-0 = <&blsp0_spi_pins>;
-			pinctrl-names = "default";
-			cs-select = <0>;
-			status = "ok";
-
-			m25p80@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <0>;
-				compatible = "n25q128a11";
-				linux,modalias = "m25p80", "n25q128a11";
-				spi-max-frequency = <50000000>;
-				use-default-sizes;
-			};
-		};
-
-		mdio0: mdio@88000 {
-			status = "ok";
-
-			ethernet-phy@0 {
-				reg = <7>;
-			};
-		};
-
-		mdio1: mdio@90000 {
-			status = "ok";
-			pinctrl-0 = <&mdio1_pins>;
-			pinctrl-names = "default";
-			phy-reset-gpio = <&tlmm 39 0>;
-
-			ethernet-phy@0 {
-				reg = <28>;
-			};
-		};
-
-		ess-instance {
-			num_devices = <0x1>;
-			ess-switch@0x39c00000 {
-				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
-				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
-				qcom,port_phyinfo {
-					port@0 {
-						port_id = <1>;
-						phy_address = <7>;
-						mdiobus = <&mdio0>;
-					};
-					port@1 {
-						port_id = <2>;
-						phy_address = <0x1c>;
-						mdiobus = <&mdio1>;
-						port_mac_sel = "QGMAC_PORT";
-					};
-				};
-				led_source@0 {
-					source = <0>;
-					mode = "normal";
-					speed = "all";
-					blink_en = "enable";
-					active = "high";
-				};
-			};
-				ess-switch1@1 {
-				compatible = "qcom,ess-switch-qca83xx";
-				device_id = <1>;
-				switch_access_mode = "mdio";
-				mdio-bus = <&mdio1>;
-				reset_gpio = <0x28>;
-				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
-				switch_lan_bmp = <0x1e>; /* lan port bitmap */
-				switch_wan_bmp = <0x0>;  /* wan port bitmap */
-				qca,ar8327-initvals = <
-						0x00004 0x7600000   /* PAD0_MODE */
-						0x00008 0x1000000   /* PAD5_MODE */
-						0x0000c 0x80        /* PAD6_MODE */
-						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
-						0x000e4 0xaa545     /* MAC_POWER_SEL */
-						0x000e0 0xc74164de  /* SGMII_CTRL */
-						0x0007c 0x4e        /* PORT0_STATUS */
-						0x00094 0x4e        /* PORT6_STATUS */
-				>;
-				qcom,port_phyinfo {
-					port@0 {
-						port_id = <1>;
-						phy_address = <28>;
-					};
-				};
-			};
-		};
-
-		dp1 {
-			device_type = "network";
-			compatible = "qcom,nss-dp";
-			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
-			clock-names = "nss-snoc-gmac-axi-clk";
-			qcom,id = <1>;
-			reg = <0x39C00000 0x10000>;
-			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-			qcom,mactype = <2>;
-			qcom,link-poll = <1>;
-			qcom,phy-mdio-addr = <7>;
-			mdio-bus = <&mdio0>;
-			local-mac-address = [000000000000];
-			phy-mode = "sgmii";
-		};
-
-		dp2 {
-			device_type = "network";
-			compatible = "qcom,nss-dp";
-			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
-			clock-names = "nss-snoc-gmac-axi-clk";
-			qcom,id = <2>;
-			reg = <0x39D00000 0x10000>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
-			qcom,mactype = <2>;
-			qcom,link-poll = <1>;
-			qcom,phy-mdio-addr = <28>;
-			mdio-bus = <&mdio1>;
-			local-mac-address = [000000000000];
-			phy-mode = "sgmii";
-		};
-
-		qcom,test@0 {
-			status = "ok";
-		};
-
-		nss-macsec1 {
-			compatible = "qcom,nss-macsec";
-			phy_addr = <0x1c>;
-			mdiobus = <&mdio1>;
-		};
-
-		lpass: lpass@0xA000000{
-			status = "disabled";
-		};
-
-		pcm: pcm@0xA3C0000{
-			pinctrl-0 = <&audio_pins>;
-			pinctrl-names = "default";
-			status = "disabled";
-		};
-
-		pcm_lb: pcm_lb@0 {
-			status = "disabled";
-		};
-	};
-
-	thermal-zones {
-		status = "ok";
-	};
-
-};
-
-&tlmm {
-	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
-	pinctrl-names = "default";
-
-	blsp0_uart_pins: uart_pins {
-		blsp0_uart_rx_tx {
-			pins = "gpio20", "gpio21";
-			function = "blsp0_uart0";
-			bias-disable;
-		};
-	};
-
-	blsp1_uart_pins: blsp1_uart_pins {
-		blsp1_uart_rx_tx {
-			pins = "gpio22", "gpio24", "gpio23", "gpio25";
-			function = "blsp1_uart2";
-			bias-disable;
-		};
-	};
-
-	blsp0_spi_pins: blsp0_spi_pins {
-		mux {
-			pins = "gpio10", "gpio11", "gpio12", "gpio13";
-			function = "blsp0_spi";
-			drive-strength = <2>;
-			bias-disable;
-		};
-	};
-
-	qspi_nand_pins: qspi_nand_pins {
-		qspi_clock {
-			pins = "gpio9";
-			function = "qspi_clk";
-			drive-strength = <8>;
-			bias-disable;
-		};
-		qspi_cs {
-			pins = "gpio8";
-			function = "qspi_cs";
-			drive-strength = <8>;
-			bias-disable;
-		};
-		qspi_data_0 {
-			pins = "gpio7";
-			function = "qspi0";
-			drive-strength = <8>;
-			bias-disable;
-		};
-		qspi_data_1 {
-			pins = "gpio6";
-			function = "qspi1";
-			drive-strength = <8>;
-			bias-disable;
-		};
-		qspi_data_2 {
-			pins = "gpio5";
-			function = "qspi2";
-			drive-strength = <8>;
-			bias-disable;
-		};
-		qspi_data_3 {
-			pins = "gpio4";
-			function = "qspi3";
-			drive-strength = <8>;
-			bias-disable;
-		};
-	};
-
-	mdio1_pins: mdio_pinmux {
-		mux_0 {
-			pins = "gpio36";
-			function = "mdc";
-			drive-strength = <8>;
-			bias-pull-up;
-		};
-
-		mux_1 {
-			pins = "gpio37";
-			function = "mdio";
-			drive-strength = <8>;
-			bias-pull-up;
-		};
-	};
-
-	phy_led_pins: phy_led_pins {
-		gephy_led_pin {
-			pins = "gpio46";
-			function = "led0";
-			drive-strength = <8>;
-			bias-pull-down;
-		};
-	};
-
-	i2c_pins: i2c_pins {
-		i2c_scl {
-			pins = "gpio25";
-			function = "blsp2_i2c1";
-			drive-strength = <8>;
-			bias-disable;
-		};
-
-		i2c_sda {
-			pins = "gpio26";
-			function = "blsp2_i2c1";
-			drive-strength = <8>;
-			bias-disable;
-		};
-	};
-
-	button_pins: button_pins {
-		reset_button {
-			pins = "gpio38";
-			function = "gpio";
-			drive-strength = <8>;
-			bias-pull-up;
-		};
-	};
-audio_pins: audio_pinmux {
-};
-        leds_pins: leds_pins {
-                led_5g {
-                        pins = "gpio34";
-                        function = "gpio";
-                        drive-strength = <8>;
-                        bias-pull-down;
-                };
-                led_2g {
-                        pins = "gpio33";
-                        function = "gpio";
-                        drive-strength = <8>;
-                        bias-pull-down;
-                };
-                led_sys {
-                        pins = "gpio26";
-                        function = "gpio";
-                        drive-strength = <8>;
-                        bias-pull-down;
-                };
-		led_onekey {
-                        pins = "gpio28";
-                        function = "gpio";
-                        drive-strength = <8>;
-                        bias-pull-down;
-                };
-        };
-};
-
-&soc {
-	gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-0 = <&button_pins>;
-		pinctrl-names = "default";
-
-		button@1 {
-			label = "reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			debounce-interval = <60>;
-		};
-	};
-
-        leds {
-                compatible = "gpio-leds";
-                pinctrl-0 = <&leds_pins>;
-                pinctrl-names = "default";
-
-                led_blue: led@34 {
-                        label = "led_5g";
-                        gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
-                        linux,default-trigger = "led_5g";
-                        default-state = "off";
-                };
-                led_green: led@33 {
-                        label = "led_2g";
-                        gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
-                        linux,default-trigger = "led_2g";
-                        default-state = "off";
-                };
-                led_red: led@26 {
-                        label = "led_sys";
-                        gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
-                        linux,default-trigger = "led_sys";
-                        default-state = "off";
-                };
-		led@28 {
-                        label = "led_onekey";
-                        gpios = <&tlmm 28 GPIO_ACTIVE_LOW>;
-                        linux,default-trigger = "led_onekey";
-                        default-state = "off";
-                };
-        };
-};
-
-&q6v5_wcss {
-	compatible = "qcom,ipq5018-q6-mpd";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	ranges;
-	firmware = "IPQ5018/q6_fw.mdt";
-	reg = <0x0cd00000 0x4040>,
-		<0x1938000 0x8>,
-		<0x193d204 0x4>;
-	reg-names = "qdsp6",
-			"tcsr-msip",
-			"tcsr-q6";
-	resets = <&gcc GCC_WCSSAON_RESET>,
-			<&gcc GCC_WCSS_Q6_BCR>;
-
-	reset-names = "wcss_aon_reset",
-			"wcss_q6_reset";
-
-	clocks = <&gcc GCC_Q6_AXIS_CLK>,
-		<&gcc GCC_WCSS_ECAHB_CLK>,
-		<&gcc GCC_Q6_AXIM_CLK>,
-		<&gcc GCC_Q6_AXIM2_CLK>,
-		<&gcc GCC_Q6_AHB_CLK>,
-		<&gcc GCC_Q6_AHB_S_CLK>,
-		<&gcc GCC_WCSS_AXI_S_CLK>;
-	clock-names = "gcc_q6_axis_clk",
-		"gcc_wcss_ecahb_clk",
-		"gcc_q6_axim_clk",
-		"gcc_q6_axim2_clk",
-		"gcc_q6_ahb_clk",
-		"gcc_q6_ahb_s_clk",
-		"gcc_wcss_axi_s_clk";
-
-	#ifdef __IPQ_MEM_PROFILE_256_MB__
-		memory-region = <&q6_mem_regions>, <&q6_etr_region>;
-	#else
-		memory-region = <&q6_mem_regions>, <&q6_etr_region>,
-				<&q6_caldb_region>;
-	#endif
-
-	qcom,rproc = <&q6v5_wcss>;
-	qcom,bootargs_smem = <507>;
-	boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>,
-			<0x2 0x4 0x2 0x12 0x0 0x0>;
-	status = "ok";
-	q6_wcss_pd1: remoteproc_pd1@4ab000 {
-		compatible = "qcom,ipq5018-wcss-ahb-mpd";
-		reg = <0x4ab000 0x20>;
-		reg-names = "rmb";
-		firmware = "IPQ5018/q6_fw.mdt";
-		m3_firmware = "IPQ5018/m3_fw.mdt";
-		interrupts-extended = <&wcss_smp2p_in 8 0>,
-					<&wcss_smp2p_in 9 0>,
-					<&wcss_smp2p_in 12 0>,
-					<&wcss_smp2p_in 11 0>;
-		interrupt-names = "fatal",
-					"ready",
-					"spawn-ack",
-					"stop-ack";
-
-		resets = <&gcc GCC_WCSSAON_RESET>,
-				<&gcc GCC_WCSS_BCR>,
-				<&gcc GCC_CE_BCR>;
-		reset-names = "wcss_aon_reset",
-				"wcss_reset",
-				"ce_reset";
-
-		clocks = <&gcc GCC_WCSS_AHB_S_CLK>,
-				<&gcc GCC_WCSS_ACMT_CLK>,
-				<&gcc GCC_WCSS_AXI_M_CLK>;
-		clock-names = "gcc_wcss_ahb_s_clk",
-					"gcc_wcss_acmt_clk",
-					"gcc_wcss_axi_m_clk";
-
-		qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
-
-		qcom,smem-states = <&wcss_smp2p_out 8>,
-					<&wcss_smp2p_out 9>,
-					<&wcss_smp2p_out 10>;
-		qcom,smem-state-names = "shutdown",
-					"stop",
-					"spawn";
-	#ifdef __IPQ_MEM_PROFILE_256_MB__
-		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
-				<&q6_etr_region>;
-	#else
-		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
-				<&q6_etr_region>, <&q6_caldb_region>;
-	#endif
-
-	};
-
-	q6_wcss_pd2: remoteproc_pd2 {
-		compatible = "qcom,ipq5018-wcss-pcie-mpd";
-		firmware = "IPQ5018/q6_fw.mdt";
-		m3_firmware = "qcn6122/m3_fw.mdt";
-		interrupts-extended = <&wcss_smp2p_in 16 0>,
-					<&wcss_smp2p_in 17 0>,
-					<&wcss_smp2p_in 20 0>,
-					<&wcss_smp2p_in 19 0>;
-		interrupt-names = "fatal",
-					"ready",
-					"spawn-ack",
-					"stop-ack";
-
-		qcom,smem-states = <&wcss_smp2p_out 16>,
-					<&wcss_smp2p_out 17>,
-					<&wcss_smp2p_out 18>;
-		qcom,smem-state-names = "shutdown",
-					"stop",
-					"spawn";
-	#ifdef __IPQ_MEM_PROFILE_256_MB__
-		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
-				<&q6_qcn6122_etr_1>;
-	#else
-		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
-				<&q6_qcn6122_etr_1>, <&q6_qcn6122_caldb_1>;
-	#endif
-
-	};
-
-	q6_wcss_pd3: remoteproc_pd3 {
-		compatible = "qcom,ipq5018-wcss-pcie-mpd";
-		firmware = "IPQ5018/q6_fw.mdt";
-		interrupts-extended = <&wcss_smp2p_in 24 0>,
-					<&wcss_smp2p_in 25 0>,
-					<&wcss_smp2p_in 28 0>,
-					<&wcss_smp2p_in 27 0>;
-		interrupt-names = "fatal",
-					"ready",
-					"spawn-ack",
-					"stop-ack";
-
-		qcom,smem-states = <&wcss_smp2p_out 24>,
-					<&wcss_smp2p_out 25>,
-					<&wcss_smp2p_out 26>;
-		qcom,smem-state-names = "shutdown",
-					"stop",
-					"spawn";
-	#ifdef	__IPQ_MEM_PROFILE_256_MB__
-		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
-				<&q6_qcn6122_etr_2>;
-	#else
-		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
-				<&q6_qcn6122_etr_2>, <&q6_qcn6122_caldb_2>;
-	#endif
-	};
-};
-
-&i2c_0 {
-	pinctrl-0 = <&i2c_pins>;
-	pinctrl-names = "default";
-	status = "disabled";
-};
-
-&wifi0 {
-	/* IPQ5018 */
-	qcom,multipd_arch;
-	qcom,rproc = <&q6_wcss_pd1>;
-	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
-#ifdef __IPQ_MEM_PROFILE_256_MB__
-	qcom,tgt-mem-mode = <2>;
-#else
-	qcom,tgt-mem-mode = <1>;
-#endif
-	qcom,board_id = <0x24>;
-#ifdef __CNSS2__
-	qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
-	qcom,caldb-addr = <0x4D400000 0x4D400000 0 0 0>;
-	qcom,caldb-size = <0x200000>;
-	mem-region = <&q6_ipq5018_data>;
-#else
-	memory-region = <&q6_ipq5018_data>;
-#endif
-	status = "ok";
-};
-
-&wifi1 {
-	/* QCN6122 5G */
-	qcom,multipd_arch;
-	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
-	qcom,rproc = <&q6_wcss_pd2>;
-#ifdef __IPQ_MEM_PROFILE_256_MB__
-	qcom,tgt-mem-mode = <2>;
-#else
-	qcom,tgt-mem-mode = <1>;
-#endif
-	qcom,board_id = <0x50>;
-#ifdef __CNSS2__
-	qcom,bdf-addr = <0x4D600000 0x4D600000 0x4D300000 0x0 0x0>;
-	qcom,caldb-addr = <0x4E800000 0x4E800000 0 0 0>;
-	qcom,caldb-size = <0x500000>;
-	mem-region = <&q6_qcn6122_data1>;
-#else
-	memory-region = <&q6_qcn6122_data1>;
-#endif
-	status = "disabled";
-};
-
-&wifi2 {
-	/* QCN6122 6G */
-	qcom,multipd_arch;
-	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
-	qcom,rproc = <&q6_wcss_pd3>;
-#ifdef __IPQ_MEM_PROFILE_256_MB__
-	qcom,tgt-mem-mode = <2>;
-#else
-	qcom,tgt-mem-mode = <1>;
-#endif
-	qcom,board_id = <0xb0>;
-#ifdef __CNSS2__
-	qcom,bdf-addr = <0x4ED00000 0x4ED00000 0x4E400000 0x0 0x0>;
-	qcom,caldb-addr = <0x4FF00000 0x4FF00000 0 0 0>;
-	qcom,caldb-size = <0x500000>;
-	mem-region = <&q6_qcn6122_data2>;
-#else
-	memory-region = <&q6_qcn6122_data2>;
-#endif
-	status = "ok";
-};
-
-
-&usb3 {
-	status = "ok";
-	device-power-gpio = <&tlmm 24 1>;
-};
-
-&dwc_0 {
-	/delete-property/ #phy-cells;
-	/delete-property/ phys;
-	/delete-property/ phy-names;
-};
-&hs_m31phy_0 {
-	status = "ok";
-};
-
-&eud {
-	status = "ok";
-};
-
-&pcie_x1 {
-	#status = "disabled";
-	#perst-gpio = <&tlmm 18 1>;
-	perst-gpio = <&tlmm 18 GPIO_ACTIVE_LOW>;
-};
-
-&pcie_x2 {
-	#status = "disabled";
-	#perst-gpio = <&tlmm 15 1>;
-	perst-gpio = <&tlmm 15 GPIO_ACTIVE_LOW>;
-};
-
-&pcie_x1_rp {
-        status = "disabled";
-
-	mhi_0: qcom,mhi@0 {
-		reg = <0 0 0 0 0 >;
-	};
-};
-
-&pcie_x2_rp {
-        status = "disabled";
-
-	mhi_1: qcom,mhi@1 {
-		reg = <0 0 0 0 0 >;
-
-	};
-};
-

feeds/ipq807x_v5.4/ipq50xx/image/ipq50xx.mk

@@ -120,15 +120,6 @@ define Device/indio_um-525axp
 endef
 TARGET_DEVICES += indio_um-525axp
 
-define Device/indio_um-525axm
-  DEVICE_TITLE := Indio UM-525axm
-  DEVICE_DTS := qcom-ipq5018-indio-um-525axm
-  SUPPORTED_DEVICES := indio,um-525axm
-  DEVICE_PACKAGES := ath11k-wifi-indio-um-525axm ath11k-firmware-ipq50xx-spruce ath11k-firmware-qcn6122
-  DEVICE_DTS_CONFIG := config@mp03.5-c1
-endef
-TARGET_DEVICES += indio_um-525axm
-
 define Device/udaya_a6_id2
   DEVICE_TITLE := Udaya A6 - ID2
   DEVICE_DTS := qcom-ipq5018-udaya-a6-id2

feeds/qca-wifi-7/ipq53xx/base-files/etc/board.d/02_network

@@ -14,12 +14,9 @@ ipq53xx_setup_interfaces()
 		;;
 	cig,wf189|\
 	edgecore,eap105|\
-	sercomm,ap72tip)
-		ucidef_set_interfaces_lan_wan "eth1" "eth0"
-		;;
+	sercomm,ap72tip|\
 	sonicfi,rap750w-311a)
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"
-		ucidef_add_switch "switch1" "0u@eth1" "3:lan" "2:lan" "1:lan"
 		;;
 	sonicfi,rap7110c-341x|\
 	sonicfi,rap750e-h|\

feeds/qca-wifi-7/ipq53xx/config-6.1

@@ -1180,7 +1180,7 @@ CONFIG_QTI_LICENSE_MANAGER=y
 # CONFIG_SYMBOLIC_ERRNAME is not set
 # CONFIG_LEDS_BRIGHTNESS_HW_CHANGED is not set
 # CONFIG_LEDS_CLASS_MULTICOLOR is not set
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y 
+# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
 # CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY is not set
 # CONFIG_PINCTRL_SINGLE is not set
 # CONFIG_RANDOM_TRUST_BOOTLOADER is not set

feeds/ucentral/ucentral-client/files/etc/ucentral/version.json

@@ -1,5 +1,5 @@
 {
 	"major": 4,
 	"minor": 1,
-	"patch": 1
+	"patch": 0
 }

feeds/ucentral/ucentral-event/files/ucentral-event

@@ -2,8 +2,6 @@
 
 'use strict';
 
-push(REQUIRE_SEARCH_PATH, '/usr/share/ucentral/*.uc');
-
 import * as libubus from 'ubus';
 import * as libuci from 'uci';
 import * as uloop from 'uloop';
@@ -38,7 +36,6 @@ let ucentral_running = false;
 let pending_events = [];
 let relay = {};
 let net_config = {};
-let vlan_refcount = {};
 
 
 function config_load() {
@@ -55,20 +52,6 @@ function config_load() {
 	net_config = {};
 }
 
-function vlan_refcount_init() {
-	let stations = require('wifi.station');
-
-	vlan_refcount = {};
-
-	for (let k, v in stations) {
-		let vlan = split(k, '-v')[1];
-		let count = length(v);
-		if (vlan && count > 0) {
-			vlan_refcount[vlan] = count;
-		}
-	}
-}
-
 function match(object, type, list) {
 	if (object in list || type in list)
 		return true;
@@ -278,24 +261,13 @@ handlers = {
 		if (config.config.swconfig)
 			return handlers.vlan_add_swconfig(notify);
 
-		let vlan_id = `${notify.data.vlan_id}`;
-		vlan_refcount[vlan_id] = (vlan_refcount[vlan_id] || 0) + 1;
-
-		let parts = split(notify.data.ifname, '-v');
-		let is_wifi_iface = (length(parts) == 2 && wildcard(parts[0], 'wlan*'));
-
-		if (vlan_refcount[vlan_id] > 1 && !is_wifi_iface)
-			return;
-
-		if (vlan_refcount[vlan_id] == 1) {
-			for (let wan in wan_ports) {
-				let msg = {
-					name: wan,
-					vlan: [ `${notify.data.vlan_id}:t` ]
-				};
-				ubus.call('network.interface.up_none', 'add_device', msg);
-				ubus.call('udevstats', 'add_device', { device: wan, vlan: +notify.data.vlan_id });
-			}
+		for (let wan in wan_ports) {
+			let msg = {
+				name: wan,
+				vlan: [ `${notify.data.vlan_id}:t` ]
+			};
+			ubus.call('network.interface.up_none', 'add_device', msg);
+			ubus.call('udevstats', 'add_device', { device: wan, vlan: +notify.data.vlan_id });
 		}
 
 		let msg = {
@@ -310,14 +282,6 @@ handlers = {
 	vlan_remove: function(notify) {
 		if (config.config.swconfig)
 			return;
-
-		let vlan_id = `${notify.data.vlan_id}`;
-		vlan_refcount[vlan_id] = (vlan_refcount[vlan_id] || 1) - 1;
-
-		if (vlan_refcount[vlan_id] > 0)
-			return;
-		delete vlan_refcount[vlan_id];
-
 		for (let wan in wan_ports) {
 			let msg = {
 				name: wan,
@@ -660,7 +624,6 @@ let ubus_methods = {
 };
 
 config_load();
-vlan_refcount_init();
 
 hapd_subscriber = ubus.subscriber(hapd_subscriber_notify_cb, hapd_subscriber_remove_cb);
 dhcp_subscriber = ubus.subscriber(dhcp_subscriber_notify_cb, dhcp_subscriber_remove_cb);

feeds/ucentral/ucentral-schema/Makefile

@@ -4,10 +4,10 @@ PKG_NAME:=ucentral-schema
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-schema.git
-PKG_MIRROR_HASH:=c0f43db0530a38eb424e81908ad47a14e1d4d8f8a86eb148e34f98187c79ba6b
+PKG_MIRROR_HASH:=d36e17c47d793fb3b0181ed92411e31a2be8e0ff6f9fad89d9704146f9f251cb
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_DATE:=2025-10-16
-PKG_SOURCE_VERSION:=dc9cad95641266a08de73aab85d931d992090159
+PKG_SOURCE_DATE:=2025-09-24
+PKG_SOURCE_VERSION:=100c045af16bc13db7af936a4cf6f675eb651974
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

feeds/ucentral/ucentral-schema/files/etc/ucentral/examples/multi-psk.json

@@ -1,12 +1,17 @@
 {
 	"uuid": 2,
 	"radios": [
+		{
+			"band": "6G",
+			"country": "CA",
+			"channel-mode": "HE",
+			"channel-width": 80
+		},
 		{
 			"band": "5G",
 			"country": "CA",
 			"channel-mode": "HE",
-			"channel-width": 80,
-			"channel": 36
+			"channel-width": 80
 		},
 		{
 			"band": "2G",
@@ -52,7 +57,10 @@
 							"key": "bbbbbbbb"
 						}
 					],
-					"roaming": true
+					"roaming": {
+						"message-exchange": "ds",
+						"generate-psk": true
+					}
 				}
 			]
 		},

feeds/ucentral/ucentral-schema/files/usr/share/ucentral/wifi_max_user.uc

@@ -1,10 +1,7 @@
 #!/usr/bin/ucode 
-import { readfile } from "fs";
 
 let nl = require("nl80211");
 let def = nl.const;
-let board_name = rtrim(readfile('/tmp/sysinfo/board_name'), '\n');
-let phy_index = 0;
 
 function phy_get() {
 	let res = nl.request(def.NL80211_CMD_GET_WIPHY, def.NLM_F_DUMP, { split_wiphy_dump: true });
@@ -15,11 +12,5 @@ function phy_get() {
 	return res;
 }
 
-switch(board_name) {
-case 'edgecore,eap112':
-        phy_index = 1;
-        break;
-}
-
 let phys = phy_get();
-printf("%d\n", phys[phy_index].max_ap_assoc || 32);
+printf("%d\n", phys[0].max_ap_assoc || 32);

patches/0058-ramips-add-mt7621_indio_um-305ax.patch

@@ -1,22 +1,16 @@
-From 937c4ba769b4d3a0b5cb804e54fd8bece8efac47 Mon Sep 17 00:00:00 2001
-From: Shubham Vishwakarma <shubhamvis98@fossfrog.in>
-Date: Mon, 29 Sep 2025 10:35:54 +0530
-Subject: [PATCH 58/68] ramips: mt7621: add mt7621 indio um-305ax
+From ec135e7aefac08806fbabb0634a2bd88a169dfc6 Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Sat, 15 Jul 2023 15:25:59 +0200
+Subject: [PATCH 58/68] ramips: add mt7621_indio_um-305ax
 
-Changelog:
-- Fix MAC address assignment for Ethernet ports
-- Fix Ethernet port configuration (was not working in the current DTS
-  because GPIOs 23 and 24, used for LEDs, are RGMII2 pins)
-- Add package kmod-7915-firmware to enable Wi-Fi
-
-Signed-off-by: Shubham Vishwakarma <shubhamvis98@fossfrog.in>
+Signed-off-by: John Crispin <john@phrozen.org>
 ---
  target/linux/ath79/image/generic.mk           |  22 +--
- .../ramips/dts/mt7621_indio_um-305ax.dts      | 168 ++++++++++++++++++
+ .../ramips/dts/mt7621_indio_um-305ax.dts      | 146 ++++++++++++++++++
  target/linux/ramips/image/mt7621.mk           |  11 ++
  .../mt7621/base-files/etc/board.d/02_network  |   6 +
  .../etc/hotplug.d/ieee80211/10_fix_wifi_mac   |   6 +
- 5 files changed, 202 insertions(+), 11 deletions(-)
+ 5 files changed, 180 insertions(+), 11 deletions(-)
  create mode 100644 target/linux/ramips/dts/mt7621_indio_um-305ax.dts
 
 diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
@@ -61,30 +55,27 @@ index 5882feafcb..a98a5e816f 100644
    DEVICE_VENDOR := YunCore
 diff --git a/target/linux/ramips/dts/mt7621_indio_um-305ax.dts b/target/linux/ramips/dts/mt7621_indio_um-305ax.dts
 new file mode 100644
-index 0000000000..42837dd9fe
+index 0000000000..79cffbdec2
 --- /dev/null
 +++ b/target/linux/ramips/dts/mt7621_indio_um-305ax.dts
-@@ -0,0 +1,168 @@
+@@ -0,0 +1,146 @@
 +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright (c) 2025, Shubham Vishwakarma <shubhamvis98@fossfrog.in>
-+ */
-+
-+/dts-v1/;
 +
 +#include "mt7621.dtsi"
++
 +#include <dt-bindings/gpio/gpio.h>
 +#include <dt-bindings/input/input.h>
 +
 +/ {
 +	compatible = "indio,um-305ax", "mediatek,mt7621-soc";
-+	model = "Indio UM-305AX";
++	model = "INDIO UM-305AX";
 +
 +	aliases {
 +		led-boot = &led_green;
-+		led-failsafe = &led_green;
-+		led-running = &led_green;
-+		led-upgrade = &led_green;
++		led-failsafe = &led_red;
++		led-running = &led_blue;
++		led-upgrade = &led_red;
++		label-mac-device = &wan_port;
 +	};
 +
 +	chosen {
@@ -93,11 +84,6 @@ index 0000000000..42837dd9fe
 +	};
 +
 +	leds {
-+		/*
-+		* GPIO 23 and 24 LEDs won’t work because these pins are part of the RGMII2 pin group.
-+		* To make the LEDs work, we need to change the &state_default node’s group variable
-+		* to "rgmii2", which restores LED functionality but disables the Ethernet ports.
-+		*/
 +		compatible = "gpio-leds";
 +
 +		led_blue: blue {
@@ -133,7 +119,7 @@ index 0000000000..42837dd9fe
 +
 +&state_default {
 +	gpio {
-+		groups = "jtag", "wdt";
++		groups = "rgmii2";
 +		function = "gpio";
 +	};
 +};
@@ -150,19 +136,15 @@ index 0000000000..42837dd9fe
 +};
 +
 +&gmac0 {
-+	status = "okay";
-+	nvmem-cells = <&macaddr_offset>;
-+	nvmem-cell-names = "mac-address";
++	mtd-mac-address = <&factory 0x4>;
 +};
 +
 +&switch0 {
 +	ports {
-+		port@0 {
++		wan_port: port@0 {
 +			status = "okay";
 +			label = "wan";
-+			nvmem-cells = <&macaddr_offset>;
-+			nvmem-cell-names = "mac-address";
-+			mac-address-increment = <1>;
++			mtd-mac-address = <&factory 0x28>;
 +		};
 +
 +		port@1 {
@@ -223,16 +205,6 @@ index 0000000000..42837dd9fe
 +	};
 +};
 +
-+&factory {
-+	compatible = "nvmem-cells";
-+	#address-cells = <1>;
-+	#size-cells = <1>;
-+
-+	macaddr_offset: macaddr@4 {
-+		reg = <0x4 0x6>;
-+	};
-+};
-+
 diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
 index 962d7ef440..8790a2fa50 100644
 --- a/target/linux/ramips/image/mt7621.mk
@@ -297,5 +269,5 @@ index 3467e783f0..d5bd50fdf7 100644
  		[ "$PHYNBR" = "1" ] && \
  			macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1 > /sys${DEVPATH}/macaddress
 -- 
-2.47.3
+2.34.1
 

profiles/cig_wf189.yml

@@ -17,4 +17,4 @@ packages:
   - sysstat
   - kmod-cig-poe-judgment
 diffconfig: |
-  CONFIG_KERNEL_IPQ_MEM_PROFILE=0
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=0 

profiles/cig_wf189w.yml

@@ -16,4 +16,4 @@ packages:
   - sysstat
   - kmod-cig-poe-judgment
 diffconfig: |
-  CONFIG_KERNEL_IPQ_MEM_PROFILE=0
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=0 

profiles/indio_um-525axm.yml

@@ -1,17 +0,0 @@
----
-profile: indio_um-525axm
-target: ipq50xx
-subtarget: generic
-description: Build image for the Indio um-525axm
-image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-indio_um-525axm-squashfs-sysupgrade.tar
-feeds:
-  - name: ipq807x
-    path: ../../feeds/ipq807x_v5.4
-include:
-  - ucentral-ap
-packages:
-  - ipq50xx
-diffconfig: |
-  CONFIG_KERNEL_IPQ_MEM_PROFILE=512
-  CONFIG_BUSYBOX_CUSTOM=y
-  CONFIG_BUSYBOX_CONFIG_STTY=y  

setup.py

@@ -87,7 +87,7 @@ def setup_tree():
 		for patch in patches:
 			run(["git", "am", "-3", str(base_dir / patch)], check=True)
 		run(
-			["ln", "-rs", profiles, "profiles"], check=True,
+			["ln", "-s", profiles, "profiles"], check=True,
 		)
 		print("### Patches done")
 	except: