Merge pull request #832 from Telecominfraproject/release-4

Release 4

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-cig-wf189.dts

@@ -44,9 +44,11 @@
 			uniphyaddr_fixup = <0xC90F014>;
 			mdio_clk_fixup; /* MDIO clock sequence fix up flag */
 			tip,clk_div = <0xff>; /* MDIO Frequency reduction*/
+			limit_rtlphy_10g_ablity;
 
 			phy0: ethernet-phy@0 {
 				reg = <8>;
+				compatible ="ethernet-phy-ieee802.3-c45";
 			};
 
 			phy1: ethernet-phy@1 {

feeds/qca-wifi-7/ipq53xx/files-6.1/drivers/net/phy/rtk/rtk_phy.c

@@ -7,6 +7,7 @@
 #include <linux/module.h>
 #include <linux/phy.h>
 #include <linux/delay.h>
+#include <linux/of.h>
 
 #include "phy_rtl826xb_patch.h"
 #include "phy_rtl8251b_patch.h"
@@ -30,6 +31,7 @@ static int rtl8251_match_phy_device(struct phy_device *phydev)
 static int rtl826xb_get_features(struct phy_device *phydev)
 {
     int ret;
+    struct device_node *np;
     ret = genphy_c45_pma_read_abilities(phydev);
     if (ret)
         return ret;
@@ -48,6 +50,14 @@ static int rtl826xb_get_features(struct phy_device *phydev)
     linkmode_clear_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT,
                        phydev->supported);
 
+    np = of_find_node_by_name(NULL, "mdio");
+    if (np)
+	if (of_property_read_bool(np, "limit_rtlphy_10g_ablity"))
+	{
+		linkmode_clear_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT, phydev->supported);
+	}
+
+
     return 0;
 }
 
@@ -80,7 +90,6 @@ static int rtkphy_config_init(struct phy_device *phydev)
         case REALTEK_PHY_ID_RTL8261N:
         case REALTEK_PHY_ID_RTL8264B:
             phydev_info(phydev, "%s:%u [RTL8261N/RTL826XB] phy_id: 0x%X PHYAD:%d\n", __FUNCTION__, __LINE__, phydev->drv->phy_id, phydev->mdio.addr);
-	    phy_modify_mmd_changed(phydev, 7, 0x20, BIT(12), 0);
 
           #if 1 /* toggle reset */
             phy_modify_mmd_changed(phydev, 30, 0x145, BIT(0)  , 1);
@@ -213,7 +222,6 @@ static int rtkphy_c45_aneg_done(struct phy_device *phydev)
 static int rtkphy_c45_read_status(struct phy_device *phydev)
 {
     int ret = 0, status = 0;
-    uint16_t local;
     phydev->speed = SPEED_UNKNOWN;
     phydev->duplex = DUPLEX_UNKNOWN;
     phydev->pause = 0;
@@ -232,9 +240,6 @@ static int rtkphy_c45_read_status(struct phy_device *phydev)
         if (ret)
             return ret;
 	
-	phy_write_mmd(phydev, 7, 0x20, 0x181);
-	local = phy_read_mmd(phydev, 7, 0x20);
-
         status =  phy_read_mmd(phydev, 31, 0xA414);
         if (status < 0)
             return status;
@@ -242,11 +247,6 @@ static int rtkphy_c45_read_status(struct phy_device *phydev)
             phydev->lp_advertising, status & BIT(11));
 
         phy_resolve_aneg_linkmode(phydev);
-	if((phydev->speed == 10000) && (local == 0x181))
-        {
-                phydev->speed = 5000;
-                phydev->duplex = DUPLEX_FULL;
-        }
     }
     else
     {

feeds/qca-wifi-7/qca-ssdk-qca/patches/0006-qca-ssdk-Fix-10G-rtl-phy-driver-for-c45-mdio-read-wr.patch

@@ -0,0 +1,116 @@
+From 85a7c62d4e3385de1a379959dd45148cfdc95b3b Mon Sep 17 00:00:00 2001
+From: huangyunxiang <huangyunxiang@cigtech.com>
+Date: Tue, 29 Apr 2025 09:56:28 +0800
+Subject: [PATCH] qca-ssdk modify rtl826x phy mdio read/write as c45 mode and
+ clear 10G ablity
+
+---
+ src/hsl/phy/rtl826xb_phy.c                | 55 ++++++-------------
+ 1 file changed, 17 insertions(+), 38 deletions(-)
+
+diff --git a/src/hsl/phy/rtl826xb_phy.c b/src/hsl/phy/rtl826xb_phy.c
+index a336348aa9..9a67b45948 100644
+--- a/src/hsl/phy/rtl826xb_phy.c
++++ b/src/hsl/phy/rtl826xb_phy.c
+@@ -48,46 +48,39 @@ void rtl826xb_phy_lock_init(void)
+ 
+ static a_uint16_t rtl826x_phy_mmd_read(a_uint32_t dev_id, a_uint32_t phy_id, a_uint16_t reg_mmd, a_uint16_t reg_id)
+ {
+-	a_uint32_t reg_id_c45 = RTL826XB_REG_ADDRESS(reg_mmd, reg_id);
+-
+-	return __hsl_phy_mii_reg_read(dev_id, phy_id, reg_id_c45);
++	return hsl_phy_mmd_reg_read(dev_id, phy_id, A_TRUE, reg_mmd, reg_id);
+ }
+ 
+ 
+ static sw_error_t rtl826x_phy_mmd_write(a_uint32_t dev_id, a_uint32_t phy_id, a_uint16_t reg_mmd, a_uint16_t reg_id, a_uint16_t reg_val)
+ {
+-	a_uint32_t reg_id_c45 = RTL826XB_REG_ADDRESS(reg_mmd, reg_id);
+-
+-	return __hsl_phy_mii_reg_write(dev_id, phy_id, reg_id_c45, reg_val);
++	return hsl_phy_mmd_reg_write(dev_id, phy_id, A_TRUE, reg_mmd, reg_id, reg_val);
+ }
+ 
+ 
+ static a_uint16_t rtl826x_phy_reg_read(a_uint32_t dev_id, a_uint32_t phy_id, a_uint32_t reg)
+ {
+-	return __hsl_phy_mii_reg_read(dev_id, phy_id, reg);
++	return hsl_phy_mii_reg_read(dev_id, phy_id, reg);
+ }
+ 
+ 
+ static sw_error_t rtl826x_phy_reg_write(a_uint32_t dev_id, a_uint32_t phy_id, a_uint32_t reg, a_uint16_t reg_val)
+ {
+-	return __hsl_phy_mii_reg_write(dev_id, phy_id, reg, reg_val);
++
++	return hsl_phy_mii_reg_write(dev_id, phy_id, reg, reg_val);
+ }
+ 
+ 
+ static a_int16_t hal_miim_mmd_read(a_uint32_t dev_id, a_uint32_t phy_id, a_uint16_t mmdAddr, a_uint16_t mmdReg)
+ {
+-	a_uint32_t reg_id_c45 = RTL826XB_REG_ADDRESS(mmdAddr, mmdReg);
+-
+-	return __hsl_phy_mii_reg_read(dev_id, phy_id, reg_id_c45);
++	return hsl_phy_mmd_reg_read(dev_id, phy_id, A_TRUE, mmdAddr, mmdReg);
+ }
+ 
+ 
+ 
+ static a_int32_t hal_miim_mmd_write(a_uint32_t dev_id, a_uint32_t phy_id, a_uint16_t mmdAddr, a_uint16_t mmdReg, a_uint16_t phy_data)
+ {
+-	a_uint32_t reg_id_c45 = RTL826XB_REG_ADDRESS(mmdAddr, mmdReg);
+-
+-	return __hsl_phy_mii_reg_write(dev_id, phy_id, reg_id_c45, phy_data);
++	return hsl_phy_mmd_reg_write(dev_id, phy_id, A_TRUE, mmdAddr, mmdReg, phy_data);
+ }
+ 
+ 
+@@ -1281,34 +1274,20 @@ phy_826xb_autoNegoAbility_set(a_uint32_t dev_id, a_uint32_t phy_id, a_uint32_t a
+ 	hsl_phy_phydev_autoneg_update(dev_id, phy_id, A_TRUE, autoneg);
+ 	
+ 	phyData = phy_common_general_reg_mmd_get(dev_id, phy_id, PHY_MMD_AN, 16);
++	phyData &= (~(0x0020 | 0x0040 | FAL_PHY_ADV_100TX_HD | FAL_PHY_ADV_100TX_FD | FAL_PHY_ADV_PAUSE | FAL_PHY_ADV_ASY_PAUSE));
++	phyData |= (autoneg & FAL_PHY_ADV_100TX_HD) ? (FAL_PHY_ADV_100TX_HD) : (0);
++	phyData |= ((autoneg & FAL_PHY_ADV_100TX_FD)) ? (FAL_PHY_ADV_100TX_FD) : (0);
+ 
+-    phyData &= (~(0x0020 | 0x0040 | 0x0080 | 0x0100 | 0x0400 | 0x0800));
+-	phyData |= ((autoneg & 1 << 1)) ? (0x0040) : (0);
+-    phyData |= ((autoneg & 1 << 2)) ? (0x0080) : (0);
+-    phyData |= ((autoneg & 1 << 3)) ? (0x0100) : (0);
+-	phyData |= ((autoneg & 1 << 4)) ? (0x0400) : (0);
+-	phyData |= ((autoneg & 1 << 5)) ? (0x0800) : (0);
+-//    phyData |= ((autoneg & 1 << 9)) ? (0x0400) : (0);
+-//    phyData |= ((autoneg & 1 << 10)) ? (0x0800) : (0);
+-
+-    phy_common_general_reg_mmd_set(dev_id, phy_id, PHY_MMD_AN, 16, phyData);
+-	
++	phy_common_general_reg_mmd_set(dev_id, phy_id, PHY_MMD_AN, 16, phyData);
+ 	phyData = phy_common_general_reg_mmd_get(dev_id, phy_id, PHY_MMD_AN, 32);
++	phyData &= (~(FAL_PHY_ADV_2500T_FD | FAL_PHY_ADV_5000T_FD | FAL_PHY_ADV_10000T_FD));
++	phyData |= (autoneg & FAL_PHY_ADV_2500T_FD) ? (FAL_PHY_ADV_2500T_FD) : (0);
++	phyData |= (autoneg & FAL_PHY_ADV_5000T_FD) ? (FAL_PHY_ADV_5000T_FD) : (0);
+ 
+-    phyData &= (~(0x4000 | 0x2000 | 0x1000));
+-    phyData |= (autoneg & 1 << 12) ? (0x0080) : (0);
+-    phyData |= (autoneg & 1 << 13) ? (0x0100) : (0);
+-    phyData |= (autoneg & 1 << 14) ? (0x1000) : (0);
+-
+-    phy_common_general_reg_mmd_set(dev_id, phy_id, PHY_MMD_AN, 32, phyData);
+-     
+-	
++	phy_common_general_reg_mmd_set(dev_id, phy_id, PHY_MMD_AN, 32, phyData);
+ 	phyData = phy_common_general_reg_mmd_get(dev_id, phy_id, PHY_MMD_VEND2, 0xA412);
+-
+-
+-    phyData &= (~(0x0100 | 0x0200));
+-    phyData |= (autoneg & 1 << 9) ? (0x0200) : (0);
+-//    phyData |= (autoneg & 1 << 5) ? (0x0200) : (0);
++	phyData &= (~(0x0100 | FAL_PHY_ADV_1000T_FD));
++	phyData |= (autoneg & FAL_PHY_ADV_1000T_FD) ? (FAL_PHY_ADV_1000T_FD) : (0);
+ 
+     phy_common_general_reg_mmd_set(dev_id, phy_id, PHY_MMD_VEND2, 0xA412, phyData);
+         
+-- 
+2.34.1
+

feeds/ucentral/ucentral-schema/Makefile

@@ -4,10 +4,10 @@ PKG_NAME:=ucentral-schema
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-schema.git
-PKG_MIRROR_HASH:=cd070141672c85e72001e2e36616aa7159c6dc8ca4bbacca1b61a41c145cde2f
+PKG_MIRROR_HASH:=280d87658fa36c1d5d6852dcb8203042eba6bbc9101ac317a2088e2dd68249da
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_DATE:=2025-01-27
-PKG_SOURCE_VERSION:=048a53d4a6cf3ef570dab9e2d10989844ae7c355
+PKG_SOURCE_VERSION:=52afdf8f1d1cb8445b6b56eba3768d0edffa63e1
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

feeds/ucentral/udhcpinject/files/etc/config/dhcpinject

@@ -5,3 +5,6 @@
 #   list ssid 'EAP101-ERICHI'
 #   list ssid 'EAP101-AKIHO'
 #   list ssid 'EAP101-DAMAYU'
+#
+# config dhcpinject 'dhcpinject'
+#   option iface_count '6'

feeds/ucentral/udhcpinject/files/etc/init.d/dhcpinject

@@ -9,9 +9,9 @@ SERVICE_NAME="dhcpinject"
 PROG=/usr/bin/udhcpinject
 
 start_service() {
-    local ssid_list=""
     local ssids=""
     local ports=""
+    local ifaces=""
 
     # Function to process each ssid
     append_ssid() {
@@ -40,6 +40,9 @@ start_service() {
 
     # Get the list of ports
     config_list_foreach uplink port append_port
+
+    # Get the iface_count
+    config_get ifaces dhcpinject iface_count
     
     # Fallback to eth0 if no ports are specified
     if [ -z "$ports" ]; then
@@ -47,11 +50,11 @@ start_service() {
     fi
 
     # Optional: Log or echo for debugging
-    logger -t dhcp_inject "Generated SSIDs=$ssids, Uplink=$ports"
+    logger -t dhcp_inject "Generated SSIDs=$ssids, Uplink=$ports, IFACEs=$ifaces"
 
     procd_open_instance "$SERVICE_NAME"
     procd_set_param command $PROG
-    procd_set_param env SSIDs="$ssids" PORTs="$ports"
+    procd_set_param env SSIDs="$ssids" PORTs="$ports" IFACEs="$ifaces"
     procd_set_param respawn 3600 10 10
     procd_set_param file /etc/config/dhcpinject
     procd_set_param reload_signal SIGHUP

feeds/ucentral/udhcpinject/src/udhcpinject.c

@@ -26,6 +26,7 @@ struct iface_info *iface_map = NULL;
 static struct port_info *ports = NULL;
 int iface_count = 0;
 int port_count = 0;
+int total_iface = 0;
 static pcap_t *handle = NULL;
 static char *provided_ssids = NULL;
 static char *provided_ports = NULL;
@@ -192,6 +193,11 @@ int parse_ssids(const char *ssids) {
         return -1;
     }
 
+    if (iface_count != total_iface) {
+        syslog(LOG_ERR, "Expect %d but only %d interfaces were found.\n", total_iface, iface_count);
+        return -1;
+    }
+
     syslog(LOG_INFO, "Found %d matching interfaces\n", iface_count);
     return 0;
 }
@@ -310,7 +316,6 @@ void signal_handler(int sig) {
         exit(0);
     } else if (sig == SIGHUP) {
         syslog(LOG_INFO, "Received reload signal, reconfiguring...\n");
-        sleep(5);
         // Clean up existing resources
         cleanup_tc();
         
@@ -561,7 +566,19 @@ int main(int argc, char *argv[]) {
     signal(SIGTERM, signal_handler);
     signal(SIGHUP, signal_handler);
 
-    sleep(5);
+    // Read IFACEs from environment variable
+    char *iface_env = getenv("IFACEs");
+    if (!iface_env) {
+        syslog(LOG_ERR, "No IFACEs provided. Exiting...\n");
+        cleanup();
+        return 1;
+    }
+    total_iface = atoi(iface_env);
+    if (total_iface <= 0) {
+        syslog(LOG_ERR, "Invalid IFACEs value: %s. Exiting...\n", iface_env);
+        cleanup();
+        return 1;
+    }
 
     provided_ssids = getenv("SSIDs");
     syslog(LOG_INFO, "Provided SSIDs: %s\n", provided_ssids);
@@ -618,4 +635,4 @@ int main(int argc, char *argv[]) {
 
     cleanup();
     return 0;
-}
+}