base-files: boot: add sync after uci-defaults

A scenario was seen where UCI config was not flushed to disk before
an AP power-cycle after uci-defaults was completed.  Since these
scripts are deleted after being ran once, there is no way to recover
without a factory reset.

Adding this sync operation proved to help avoid this situation from
happening

Signed-off-by: Paul White <paul@shasta.cloud>

feeds/ipq807x_v5.4/hostapd/files/afc_location.uc

@@ -4,19 +4,19 @@ let fs = require("fs");
 let ubus = require('ubus').connect();
 
 let gps_info = ubus.call('gps', 'info');
-let latitude = gps_info.latitude ?? 0;
-let longitude = gps_info.longitude ?? 0;
+let latitude = gps_info.latitude || 0;
+let longitude = gps_info.longitude || 0;
 
 // afc-location.json file content
 let afc_location = {};
 afc_location.location_type = "ellipse";
 afc_location.location = longitude + ":" + latitude ;
-afc_location.height = gps_info.elevation ?? 0;
+afc_location.height = gps_info.elevation || 0;
 afc_location.height_type = "AMSL";
-afc_location.major_axis = gps_info.major_axis ?? 0;
-afc_location.minor_axis = gps_info.minor_axis ?? 0;
-afc_location.orientation = gps_info.major_orientation ?? 0;
-afc_location.vertical_tolerance = gps_info.vdop ?? 0;
+afc_location.major_axis = int(gps_info.major_axis) || 1;
+afc_location.minor_axis = int(gps_info.minor_axis) || 1;
+afc_location.orientation = gps_info.major_orientation || 0;
+afc_location.vertical_tolerance = int(gps_info.vdop) || 1;
 
 let afc_location_json = fs.open("/etc/ucentral/afc-location.json", "w");
 afc_location_json.write(afc_location);

feeds/ipq807x_v5.4/hostapd/files/hostapd.uc

@@ -1,7 +1,8 @@
 let libubus = require("ubus");
-import { open, readfile } from "fs";
+import { open, readfile, writefile } from "fs";
 import { wdev_create, wdev_remove, is_equal, vlist_new, phy_is_fullmac, phy_open } from "common";
 
+let uci = require('uci').cursor();
 let ubus = libubus.connect(null, 60);
 
 hostapd.data.config = {};
@@ -893,10 +894,24 @@ return {
 		hostapd.ubus.disconnect();
 	},
 	afc_request: function(iface, data) {
-		let ret = ubus.call("afc", "request", { data });
-		if (type(ret) != "object")
-			return;
-		return ret.data;
+		let wireless_config = uci.get_all('wireless');
+		for (let l, afc_server in wireless_config) {
+			if (afc_server['.type'] == 'afc-server' && afc_server.url && data) {
+				hostapd.printf(`Sending AFC request: ${data}`);
+				writefile("/tmp/afc-request.json", data);
+
+				if (afc_server.access_token)
+					system(`curl -s -X POST ${afc_server.url} -H \'accept: \*\/\*\' -H \'Authorization: Bearer ${afc_server.access_token}\' -H \'Content-Type: application/json\' -d \'${data}\' --output /tmp/afc-response.json`);
+				else if (afc_server.cert)
+					system(`curl -s -X POST ${afc_server.url} -H \'accept: \*\/\*\' --cert \'${afc_server.cert}\' -H \'Content-Type: application/json\' -d \'${data}\' --output /tmp/afc-response.json`);
+
+				let afc_response = (readfile("/tmp/afc-response.json"));
+				if (afc_response)
+					return afc_response;
+				else
+					return;
+			}
+		}
 	},
 	bss_add: function(name, obj) {
 		bss_event("add", name);

feeds/ipq807x_v5.4/ipq50xx/base-files/lib/upgrade/platform.sh

@@ -107,29 +107,42 @@ platform_do_upgrade() {
 
 	board=$(board_name)
 	case $board in
-	glinet,b3000|\
 	edgecore,oap101|\
 	edgecore,oap101-6e|\
 	edgecore,oap101e|\
 	edgecore,oap101e-6e|\
 	edgecore,eap104)
+		if [ "$(find_mtd_chardev rootfs)" ]; then
+			CI_UBIPART="rootfs"
+		else
+			if grep -q rootfs1 /proc/cmdline; then
+				CI_UBIPART="rootfs2"
+				CI_FWSETENV="active 2"
+			else
+				CI_UBIPART="rootfs1"
+				CI_FWSETENV="active 1"
+			fi
+		fi
+		nand_upgrade_tar "$1"
+		;;
+	glinet,b3000)
 		CI_UBIPART="rootfs1"
 		[ "$(find_mtd_chardev rootfs)" ] && CI_UBIPART="rootfs"
 		nand_upgrade_tar "$1"
 		;;
-        hfcl,ion4x_w|\
+	hfcl,ion4x_w|\
 	hfcl,ion4xi_w)
-                wp_part=$(fw_printenv primary | cut  -d = -f2)
-                echo "Current Primary is $wp_part"
-                if [[ $wp_part == 1 ]]; then
-                        CI_UBIPART="rootfs"
-                        CI_FWSETENV="primary 0"
-                else
-                        CI_UBIPART="rootfs_1"
-                        CI_FWSETENV="primary 1"
-                fi
-                nand_upgrade_tar "$1"
-                ;;
+		wp_part=$(fw_printenv primary | cut  -d = -f2)
+		echo "Current Primary is $wp_part"
+		if [[ $wp_part == 1 ]]; then
+				CI_UBIPART="rootfs"
+				CI_FWSETENV="primary 0"
+		else
+				CI_UBIPART="rootfs_1"
+				CI_FWSETENV="primary 1"
+		fi
+		nand_upgrade_tar "$1"
+		;;
 	cig,wf186w|\
 	cig,wf186h|\
 	emplus,wap385c|\

feeds/mediatek-sdk/mediatek/mt7981/base-files/etc/hotplug.d/iface/99-mtk-sr-scene-cond

@@ -34,13 +34,11 @@ case "$board" in
 
         if [ -f "$phy0_file" ]; then
             check_phy0=$(cat $phy0_file)
-            echo "check_phy0 = $check_phy0"
             [ "$check_phy0" == 0 ] && echo 1 > $phy0_file
         fi
 
         if [ -f "$phy1_file" ]; then
             check_phy1=$(cat $phy1_file)
-            echo "check_phy1 = $check_phy1"
             [ "$check_phy1" == 0 ] && echo 1 > $phy1_file
         fi
 

feeds/qca-wifi-7/hostapd/files/afc_location.uc

@@ -4,19 +4,19 @@ let fs = require("fs");
 let ubus = require('ubus').connect();
 
 let gps_info = ubus.call('gps', 'info');
-let latitude = gps_info.latitude ?? 0;
-let longitude = gps_info.longitude ?? 0;
+let latitude = gps_info.latitude || 0;
+let longitude = gps_info.longitude || 0;
 
 // afc-location.json file content
 let afc_location = {};
 afc_location.location_type = "ellipse";
 afc_location.location = longitude + ":" + latitude ;
-afc_location.height = gps_info.elevation ?? 0;
+afc_location.height = gps_info.elevation || 0;
 afc_location.height_type = "AMSL";
-afc_location.major_axis = gps_info.major_axis ?? 0;
-afc_location.minor_axis = gps_info.minor_axis ?? 0;
-afc_location.orientation = gps_info.major_orientation ?? 0;
-afc_location.vertical_tolerance = gps_info.vdop ?? 0;
+afc_location.major_axis = int(gps_info.major_axis) || 1;
+afc_location.minor_axis = int(gps_info.minor_axis) || 1;
+afc_location.orientation = gps_info.major_orientation || 0;
+afc_location.vertical_tolerance = int(gps_info.vdop) || 1;
 
 let afc_location_json = fs.open("/etc/ucentral/afc-location.json", "w");
 afc_location_json.write(afc_location);

feeds/qca-wifi-7/hostapd/files/hostapd.uc

@@ -1,7 +1,8 @@
 let libubus = require("ubus");
-import { open, readfile } from "fs";
+import { open, readfile, writefile } from "fs";
 import { wdev_remove, is_equal, vlist_new, phy_is_fullmac, phy_open, wdev_set_radio_mask } from "common";
 
+let uci = require('uci').cursor();
 let ubus = libubus.connect(null, 60);
 
 hostapd.data.config = {};
@@ -1006,7 +1007,6 @@ let main_obj = {
 hostapd.data.ubus = ubus;
 hostapd.data.obj = ubus.publish("hostapd", main_obj);
 
-
 let auth_obj = {};
 hostapd.data.auth_obj = ubus.publish("hostapd-auth", auth_obj);
 
@@ -1026,10 +1026,24 @@ return {
 		hostapd.ubus.disconnect();
 	},
 	afc_request: function(iface, data) {
-		let ret = ubus.call("afc", "request", { data });
-		if (type(ret) != "object")
-			return;
-		return ret.data;
+		let wireless_config = uci.get_all('wireless');
+		for (let l, afc_server in wireless_config) {
+			if (afc_server['.type'] == 'afc-server' && afc_server.url && data) {
+				hostapd.printf(`Sending AFC request: ${data}`);
+				writefile("/tmp/afc-request.json", data);
+
+				if (afc_server.access_token)
+					system(`curl -s -X POST ${afc_server.url} -H \'accept: \*\/\*\' -H \'Authorization: Bearer ${afc_server.access_token}\' -H \'Content-Type: application/json\' -d \'${data}\' --output /tmp/afc-response.json`);
+				else if (afc_server.cert)
+					system(`curl -s -X POST ${afc_server.url} -H \'accept: \*\/\*\' --cert \'${afc_server.cert}\' -H \'Content-Type: application/json\' -d \'${data}\' --output /tmp/afc-response.json`);
+
+				let afc_response = (readfile("/tmp/afc-response.json"));
+				if (afc_response)
+					return afc_response;
+				else
+					return;
+			}
+		}
 	},
 	bss_create: function(phy, name, obj) {
 		phy = hostapd.data.config[phy];

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap7110c-341x.dts

@@ -31,6 +31,20 @@
 		stdout-path = "serial0";
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+	};
+
 	soc@0 {
 		mdio:mdio@90000 {
 			pinctrl-0 = <&mdio1_pins>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap750e-h.dts

@@ -190,6 +190,14 @@
 		/delete-node/ wcnss@4a900000;
 		/delete-node/ q6_caldb_region@4ce00000;
 
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
 		q6_mem_regions: q6_mem_regions@4A900000  {
 		        no-map;
 		        reg = <0x0 0x4A900000 0x0 0x5100000>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap750e-s.dts

@@ -190,6 +190,14 @@
 		/delete-node/ wcnss@4a900000;
 		/delete-node/ q6_caldb_region@4ce00000;
 
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
 		q6_mem_regions: q6_mem_regions@4A900000  {
 		        no-map;
 		        reg = <0x0 0x4A900000 0x0 0x5100000>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap750w-311a.dts

@@ -190,6 +190,14 @@
 		/delete-node/ wcnss@4a900000;
 		/delete-node/ q6_caldb_region@4ce00000;
 
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
 		q6_mem_regions: q6_mem_regions@4A900000  {
 		        no-map;
 		        reg = <0x0 0x4A900000 0x0 0x5100000>;

feeds/qca-wifi-7/qca-ssdk-qca/Makefile

@@ -100,6 +100,7 @@ endif
 ifdef CONFIG_TARGET_PROFILE
 TARGET_PROFILE=$(subst ",,$(CONFIG_TARGET_PROFILE))
 PATCH_PROFILE_NAME=patches-$(subst DEVICE_,,$(TARGET_PROFILE))
+FILES_PROFILE_NAME=files-$(subst DEVICE_,,$(TARGET_PROFILE))
 endif
 
 QCASSDK_CONFIG_OPTS+= TOOL_PATH=$(TOOLCHAIN_BIN_PATH) \
@@ -202,6 +203,15 @@ define patch_profile
 	$(call PatchDir/Default,$(PKG_BUILD_DIR),./$(PATCH_PROFILE_NAME))
 endef
 
+define files_profile
+
+	if [ -d "./$(FILES_PROFILE_NAME)" ]; then \
+		$(CP) ./$(FILES_PROFILE_NAME)/* ./files/ ; \
+	fi
+endef
+
 Hooks/Prepare/Post += patch_profile
+Hooks/Prepare/Post += files_profile
+
 $(eval $(call KernelPackage,qca-ssdk-qca-nohnat))
 $(eval $(call KernelPackage,qca-ssdk-qca-hnat))

feeds/qca-wifi-7/qca-ssdk-qca/files-zyxel_nwa130be/qca-ssdk

@@ -0,0 +1,317 @@
+#!/bin/sh /etc/rc.common
+# Copyright (c) 2018, 2021, The Linux Foundation. All rights reserved.
+# Copyright (c) 2022-2024, Qualcomm Innovation Center, Inc. All rights reserved.
+#
+# Permission to use, copy, modify, and/or distribute this software for any
+# purpose with or without fee is hereby granted, provided that the above
+# copyright notice and this permission notice appear in all copies.
+#
+# THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+# WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+# MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+# ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+# WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+# ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+# OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+#
+
+START=16
+
+#!/bin/sh
+ruletype="ip4 ip6"
+side="wan lan"
+qwan="1 3 2 0 5 7 6 4"
+qlan="0 1 2 3 4 5 6 7"
+
+function create_war_acl_rules(){
+	for lw in $side
+	do
+		#echo $lw
+		if [ "$lw" == "wan" ];then
+			listid=254
+			queue=$qwan
+			portmap=0x20
+		else
+			listid=255
+			queue=$qlan
+			portmap=0x1e
+		fi
+		#echo $queue
+		#echo "creating list $listid"
+		ssdk_sh acl list create $listid 255
+		ruleid=0
+		for rt in $ruletype
+		do
+			for qid in $queue
+			do
+				cmd="ssdk_sh acl rule add $listid $ruleid  1 n 0 0"
+				#echo $cmd
+				if [ "$rt" == "ip4" ];then
+					cmd="$cmd ip4 n n n n n n n n n n n n n n n n n n n n n n n n n n n n n"
+					#echo $cmd
+				else
+					cmd="$cmd ip6 n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n"
+					#echo $cmd
+				fi
+				if [ $ruleid -le 3 ];then
+					#non-zero dscp
+					cmd="$cmd y 0x0 0xff"
+				elif [ $ruleid -le 7 ];then
+					#zero dscp
+					cmd="$cmd n"
+				elif [ $ruleid -le 11 ];then
+					#non-zero dscp
+					cmd="$cmd y 0x0 0xff"
+				else
+					#zero dscp
+					cmd="$cmd n"
+				fi
+				p=$((ruleid/2))
+				cmd="$cmd y mask $((ruleid%2)) 0x1 y mask $((p%2)) 0x1 n n n n n n n n n n n n n n n y n n n n n n n y $qid n n 0 0 n n n n n n n n n n n n n n n n n n n n 0"
+				#echo $cmd
+				$cmd
+				ruleid=`expr $ruleid + 1`
+			done
+		done
+		ssdk_sh acl list bind $listid 0 1 $portmap
+	done
+}
+
+function create_war_cosmap(){
+	ssdk_sh cosmap pri2q set 0 0
+	ssdk_sh cosmap pri2q set 1 0
+	ssdk_sh cosmap pri2q set 2 0
+	ssdk_sh cosmap pri2q set 3 0
+	ssdk_sh cosmap pri2q set 4 1
+	ssdk_sh cosmap pri2q set 5 1
+	ssdk_sh cosmap pri2q set 6 1
+	ssdk_sh cosmap pri2q set 7 1
+	ssdk_sh cosmap pri2ehq set 0 0
+	ssdk_sh cosmap pri2ehq set 1 0
+	ssdk_sh cosmap pri2ehq set 2 0
+	ssdk_sh cosmap pri2ehq set 3 0
+	ssdk_sh cosmap pri2ehq set 4 1
+	ssdk_sh cosmap pri2ehq set 5 1
+	ssdk_sh cosmap pri2ehq set 6 1
+	ssdk_sh cosmap pri2ehq set 7 1
+}
+
+function create_acl_byp_egstp_rules(){
+	chip_ver=$1
+	cmd="ssdk_sh servcode config set 1 n 0 0xfffefc7f 0xffbdff 0 0 0 0 0 0"
+	if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		cmd="$cmd 0"
+	fi
+	#echo $cmd
+	$cmd
+
+	ssdk_sh acl list create 56 48
+	#action bypass eg stp check
+	action="y n n n n n n n n n n 0 0 n n n n n n n n n n n n n y n n n n n n n n n n n n y n n n n n n n n n n n n n n n n n n"
+	if [ "$chip_ver" == "0x2000" ]; then
+		action="$action n n 0"
+	elif [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		action="$action n n n 0"
+	else
+		action="$action 0"
+	fi
+
+	for ruleid in $( seq 0 2 )
+	do
+		if [ "$ruleid" == "0" ];then
+			cmd="ssdk_sh acl rule add 56 0 1 n 0 0 mac n n n n n y 01-80-c2-00-00-00 ff-ff-ff-ff-ff-ff n n n n n n n n n n n n n n n n n n n n n n n"
+		elif [ "$ruleid" == "1" ];then
+			cmd="ssdk_sh acl rule add 56 1 1 n 0 0 mac n n n n n n n yes 0x8809 0xffff n n n n n n n n n n n n n n n n n n n n n"
+		else
+			cmd="ssdk_sh acl rule add 56 2 1 n 0 0 mac n n n n n n n yes 0x888e 0xffff n n n n n n n n n n n n n n n n n n n n n"
+		fi
+		if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+			cmd="$cmd n $action"
+		else
+			cmd="$cmd $action"
+		fi
+		#echo $cmd
+		$cmd
+	done
+	ssdk_sh acl list bind 56 0 2 1
+}
+
+function delete_war_acl_rules(){
+	for lw in $side
+	do
+		#echo $lw
+		if [ "$lw" == "wan" ];then
+			listid=254
+			queue=$qwan
+			portmap=0x20
+		else
+			listid=255
+			queue=$qlan
+			portmap=0x1e
+		fi
+		ssdk_sh acl list unbind $listid 0 1 $portmap
+		for rt in $ruletype
+		do
+			for qid in $queue
+			do
+				cmd="ssdk_sh acl rule del $listid 0 1"
+				echo $cmd
+				$cmd
+			done
+		done
+		#echo "deleting list $listid"
+		ssdk_sh acl list destroy $listid
+	done
+}
+
+function delete_war_cosmap(){
+	ssdk_sh cosmap pri2q set 0 0
+	ssdk_sh cosmap pri2q set 1 0
+	ssdk_sh cosmap pri2q set 2 1
+	ssdk_sh cosmap pri2q set 3 1
+	ssdk_sh cosmap pri2q set 4 2
+	ssdk_sh cosmap pri2q set 5 2
+	ssdk_sh cosmap pri2q set 6 3
+	ssdk_sh cosmap pri2q set 7 3
+	ssdk_sh cosmap pri2ehq set 0 1
+	ssdk_sh cosmap pri2ehq set 1 0
+	ssdk_sh cosmap pri2ehq set 2 2
+	ssdk_sh cosmap pri2ehq set 3 2
+	ssdk_sh cosmap pri2ehq set 4 3
+	ssdk_sh cosmap pri2ehq set 5 3
+	ssdk_sh cosmap pri2ehq set 6 4
+	ssdk_sh cosmap pri2ehq set 7 5
+}
+
+function delete_acl_byp_egstp_rules(){
+	chip_ver=$1
+	cmd="ssdk_sh servcode config set 1 n 0 0xfffefcff 0xffbfff 0 0 0 0 0 0"
+	if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		cmd="$cmd 0"
+	fi
+	#echo $cmd
+	$cmd
+	ssdk_sh acl list unbind 56 0 2 1
+	ssdk_sh acl rule del 56 0 1
+	ssdk_sh acl rule del 56 1 1
+	ssdk_sh acl rule del 56 2 1
+	ssdk_sh acl list destroy 56
+}
+
+function edma_war_config_add(){
+	create_war_cosmap
+	ssdk_sh acl status set enable
+	create_war_acl_rules
+}
+
+function edma_war_config_del(){
+	delete_war_acl_rules
+	delete_war_cosmap
+}
+
+function ipq50xx_serdes_monitor () {
+	#if qca808x phy exist, need to monitor the serdes to avoid the effect for WIFI
+	port_id=2
+	old_linkstatus="DISABLE"
+	phy_id_info=`ssdk_sh port phyid get $port_id | grep Org | awk -F '!' '{print $2}'`
+	if [ "$phy_id_info" = "[Org ID]:0x004d[Rev ID]:0xd101" ]; then
+		ssdk_sh debug phy set 29 0xb 0x300d
+		ssdk_sh debug uniphy set 0 0x7ac 0x300d 4
+
+		while true
+		do
+			cur_linkstatus=`ssdk_sh port linkstatus get $port_id | grep Status | awk -F ':' '{print $2}'`
+			#when qca808x phy link status is from down to up, serdes tx would be enabled
+			if [ "$cur_linkstatus" = "ENABLE" ] && [ "$old_linkstatus" = "DISABLE" ]; then
+				ssdk_sh debug phy set 29 0xb 0xb00d
+				ssdk_sh debug uniphy set 0 0x7ac 0xb00d 4
+			fi
+			#when qca808x phy link status is from up to down, serdes tx would be disabled
+			if [ "$cur_linkstatus" = "DISABLE" ] && [ "$old_linkstatus" = "ENABLE" ]; then
+				ssdk_sh debug phy set 29 0xb 0x300d
+				ssdk_sh debug uniphy set 0 0x7ac 0x300d 4
+			fi
+			old_linkstatus=$cur_linkstatus
+		done
+	fi
+}
+
+function ipq53xx_phy_amplitude_set () {
+	#for qca808x phy sgmii, set half amplitude with src_half_swing register
+	port_id=2
+	phy_id_info=`ssdk_sh port phyid get $port_id | grep Org | awk -F '!' '{print $2}'`
+	if [ "$phy_id_info" = "[Org ID]:0x004d[Rev ID]:0xd180" ]; then
+		ssdk_sh debug phy set 5 0x40010087 0x208a
+		ssdk_sh debug phy set 6 0x40010087 0x208a
+		#Set the Reg0x67 bits[7:5]=3’b000 and bit4=1’b1
+		ampl_val=$(eval "ssdk_sh debug phy get 5 0x40010067 | grep SSDK | grep -oE '0x[0-9a-fA-F]+' | sed 's/\(0x..\)./\11/'")
+		ssdk_sh debug phy set 5 0x40010067 $ampl_val
+		ampl_val=$(eval "ssdk_sh debug phy get 6 0x40010067 | grep SSDK | grep -oE '0x[0-9a-fA-F]+' | sed 's/\(0x..\)./\11/'")
+		ssdk_sh debug phy set 6 0x40010067 $ampl_val
+	fi
+}
+
+function ipq53xx_uniphy_amplitude_set () {
+	#for ipq50xx sgmii, set half amplitude with tx_emp_lvl/margin_index and tx_margin
+	ssdk_sh debug uniphy set 0 0x7ac 0xb10d 4
+	ssdk_sh debug uniphy set 0 0x24 0 4
+	ssdk_sh debug uniphy set 1 0x7ac 0xb10d 4
+	ssdk_sh debug uniphy set 1 0x24 0 4
+}
+
+ssdk_dependency() {
+	counter=0
+	[ -e /lib/modules/$(uname -r)/qca-ssdk.ko ] && [ ! -d /sys/module/qca_ssdk ] && {
+		insmod qca-ssdk.ko
+	}
+	while [ ! -d /sys/ssdk ] && [ "$counter" -le 5 ]
+	do
+		sleep 1
+		counter=$((counter+1))
+	done
+}
+
+start() {
+	ssdk_dependency
+	chip_ver=`ssdk_sh debug reg get 0 4 | grep Data | tr -d 'SSDK Init OK![Data]:'`
+	#The following commands should be uncommented to enable EDMA WAR
+	if [ "$chip_ver" = "0x1401" ]; then
+		#edma_war_config_add
+		echo ''
+	fi
+	#The following commands should be uncommented to add acl egress stp bypass rules
+	if [ "$chip_ver" = "0x1500" ] || [ "$chip_ver" = "0x1501" ] || [ "$chip_ver" = "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		#create_acl_byp_egstp_rules $chip_ver
+		echo ''
+	fi
+	#The following commands should be uncommented to enable WAR for ipq50xx
+	chip_type_info=`cat tmp/sysinfo/model`
+	result=$(echo $chip_type_info | grep "IPQ5018")
+	if [ "$result" != "" ]; then
+		#ipq50xx_serdes_monitor &
+		#ipq50xx_uniphy_amplitude_set
+		#ipq50xx_phy_amplitude_set
+		echo ''
+	fi
+	if [ "$chip_ver" = "0x2001" ]; then
+		ipq53xx_uniphy_amplitude_set
+		ipq53xx_phy_amplitude_set
+		echo ''
+	fi
+	echo starting
+}
+
+stop() {
+	chip_ver=`ssdk_sh debug reg get 0 4 | grep Data | tr -d 'SSDK Init OK![Data]:'`
+	#The following commands should be uncommented to disable EDMA WAR
+	if [ "$chip_ver" = "0x1401" ]; then
+		#edma_war_config_del
+		echo ''
+	fi
+	#The following commands should be uncommented to delete acl egress stp bypass rules
+	if [ "$chip_ver" = "0x1500" ] || [ "$chip_ver" = "0x1501" ] || [ "$chip_ver" = "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		#delete_acl_byp_egstp_rules $chip_ver
+		echo ''
+	fi
+	echo stoping
+}

feeds/tip/certificates/files/etc/init.d/early_boot

@@ -20,6 +20,7 @@ copy_certificates() {
 	[ -z "$country" ] && country=US
 	echo "options cfg80211 ieee80211_regdom="$country > /etc/modules.conf 
 	echo -n $country > /etc/ucentral/country
+	sync
 	exit 0
 }
 

feeds/tip/certificates/files/usr/bin/mount_certs

@@ -6,13 +6,16 @@ check_certificates() {
 
 check_certificates
 
-bootconfig_lookup() {
-	case "$(fw_printenv -n cert_part)" in
-	0)	echo "0:BOOTCONFIG"
-		;;
-	1)	echo "0:BOOTCONFIG1"
-		;;
-	esac
+tar_part_lookup() {
+	part="$(fw_printenv -n cert_part)"
+	if [ "$part" -eq 0 ]; then
+		echo "$2"
+		part=1
+	else
+		echo "$1"
+		part=0
+	fi
+	fw_setenv cert_part $part
 }
 
 . /lib/functions.sh
@@ -35,13 +38,40 @@ sonicfi,rap7*)
 		[ -n "$mtd" ] && mount -t ext4 /dev/mtdblock$mtd /certificates
 	fi
 	if [ ! -f /certificates/cert.pem ] || [ ! -f /certificates/key.pem ]; then
-		bootconfig=$(bootconfig_lookup)
-		if [ -n "$bootconfig" ]; then
-			mmc_dev=$(echo $(find_mmc_part "$bootconfig") | sed 's/^.\{5\}//')
+		part=$(tar_part_lookup "0:BOOTCONFIG" "0:BOOTCONFIG1")
+		if [ -n "part" ]; then
+			mmc_dev=$(echo $(find_mmc_part "$part") | sed 's/^.\{5\}//')
 			[ -n "$mmc_dev" ] && tar xf /dev/$mmc_dev -C /certificates
 		fi
 	fi
 	;;
+udaya,a5-id2|\
+yuncore,ax820)
+	mtd=$(find_mtd_index certificates)
+	if [ "$(head -c 4 /dev/mtd$mtd)" == "hsqs" ]; then
+		mount -t squashfs /dev/mtdblock$mtd /mnt
+		cp /mnt/* /certificates
+		umount /mnt
+	fi
+	part=$(tar_part_lookup "insta1" "insta2")
+	if [ -n "insta" ]; then
+		mtd=$(find_mtd_index $part)
+		[ -n "$mtd" ] && tar xf /dev/mtdblock$mtd -C /certificates
+	fi
+	;;
+sonicfi,rap6*)
+	mtd=$(find_mtd_index certificates)
+	if [ "$(head -c 4 /dev/mtd$mtd)" == "hsqs" ]; then
+		mount -t squashfs /dev/mtdblock$mtd /mnt
+		cp /mnt/* /certificates
+		umount /mnt
+	fi
+	part=$(tar_part_lookup "devinfo" "certificates")
+	if [ -n "$part" ]; then
+		mtd=$(find_mtd_index $part)
+		[ -n "$mtd" ] && tar xf /dev/mtdblock$mtd -C /certificates
+	fi
+	;;
 *)
 	mtd=$(find_mtd_index certificates)
 

feeds/tip/certificates/files/usr/bin/store_certs

@@ -1,25 +1,44 @@
 #!/bin/sh
 
-bootconfig_lookup() {
-	bootconfig="$(fw_printenv -n cert_part)"
-	case "$(fw_printenv -n cert_part)" in
-	0)	echo "0:BOOTCONFIG1"
-		bootconfig=1
-		;;
-	*)	echo "0:BOOTCONFIG"
-		bootconfig=0
-		;;
-	esac
-	fw_setenv cert_part $bootconfig
+tar_part_lookup() {
+	part="$(fw_printenv -n cert_part)"
+	if [ "$part" -eq 0 ]; then
+		echo "$2"
+		part=1
+	else
+		echo "$1"
+		part=0
+	fi
+	fw_setenv cert_part $part
 }
 
 . /lib/functions.sh
 case "$(board_name)" in
 sonicfi,rap7110c-341x)
 	cd /certificates
-	tar cf /tmp/certs.tar
-	bootconfig=$(bootconfig_lookup)
-	mmc_dev=$(echo $(find_mmc_part $bootconfig) | sed 's/^.\{5\}//')
-	dd if=/tmp/certs.tar of=/dev/$bootconfig
+	tar cf /tmp/certs.tar .
+	part=$(tar_part_lookup "0:BOOTCONFIG" "0:BOOTCONFIG1")
+	mmc_dev=$(echo $(find_mmc_part $part) | sed 's/^.\{5\}//')
+	dd if=/tmp/certs.tar of=/dev/$mmc_dev
+	;;
+udaya,a5-id2|\
+yuncore,ax820)
+	cd /certificates
+	tar cf /tmp/certs.tar .
+	part=$(tar_part_lookup "insta1" "insta2")
+	mtd=$(find_mtd_index $part)
+	dd if=/tmp/certs.tar of=/dev/mtdblock$mtd
+	;;
+sonicfi,rap6*)
+	if [ "$(fw_printenv -n store_certs_disabled)" != "1" ]; then
+		cd /certificates
+		tar cf /tmp/certs.tar .
+		part=$(tar_part_lookup "devinfo" "certificates")
+		mtd=$(find_mtd_index $part)
+		block_size=$(cat /sys/class/mtd/mtd$mtd/size)
+		dd if=/tmp/certs.tar of=/tmp/certs_pad.tar bs=$block_size conv=sync
+		mtd write /tmp/certs_pad.tar /dev/mtd$mtd
+		rm -f /tmp/certs.tar /tmp/certs_pad.tar
+	fi
 	;;
 esac

feeds/tip/cloud_discovery/files/etc/init.d/cloud_discover

@@ -22,6 +22,19 @@ start_service() {
 	[ "$valid" == "true" ] || 
 		/usr/share/ucentral/ucentral.uc /etc/ucentral/ucentral.cfg.0000000001 > /dev/null
 
+	est_client check
+	[ $? -eq 1 ] && {
+		logger ERROR
+		logger ERROR
+		logger ERROR
+		logger The certificate used has a CN that does not match the serial of the device
+		echo The certificate used has a CN that does not match the serial of the device
+		logger ERROR
+		logger ERROR
+		logger ERROR
+		return
+	}
+
 	procd_open_instance
 	procd_set_param command "$PROG"
 	procd_set_param respawn

feeds/tip/cloud_discovery/files/usr/bin/cloud_discovery

@@ -27,6 +27,8 @@ let timeouts = {
 	'validate': 120,
 	'orphan': 2 * 60 * 60,
 	interval: 10000,
+	expiry_interval: 60 * 60 * 1000,
+	expiry_threshold: 3 * 24 * 60 * 60,
 };
 
 ulog_open(ULOG_SYSLOG | ULOG_STDIO, LOG_DAEMON, "cloud_discover");
@@ -91,6 +93,7 @@ function gateway_write(data) {
 	}
 	if (changed)
 		fs.writefile('/etc/ucentral/gateway.json', new);
+		system('sync');
 	return changed;
 }
 
@@ -328,6 +331,27 @@ let ubus_methods = {
 	},
 };
 
+function expiry_handler() {
+	let stat = fs.stat('/etc/ucentral/operational.ca');
+	if (!stat)
+		return;
+
+	let ret = system(`openssl x509 -checkend ${timeouts.expiry_threshold} -noout -in /certificates/operational.pem`);
+	if (!ret) {
+		ulog(LOG_INFO, 'checked certificate expiry - all ok\n');
+		return;
+	}
+
+	ulog(LOG_INFO, 'certificate will expire soon\n');
+	if (system('/usr/bin/est_client reenroll')) {
+		ulog(LOG_INFO, 'reenroll failed\n');
+		return;
+	}
+	ulog(LOG_INFO, 'reenroll succeeded\n');
+	ulog(LOG_INFO, '(re)starting client\n');
+	system('/etc/init.d/ucentral restart');
+}
+
 if (gateway_available()) {
 	let status = ubus.call('ucentral', 'status');
 	ulog(LOG_INFO, 'cloud is known\n');
@@ -344,6 +368,7 @@ if (gateway_available()) {
 timeouts_load();
 
 interval = uloop.interval(timeouts.interval, interval_handler);
+uloop.interval(timeouts.expiry_interval, expiry_handler);
 
 ubus.publish('cloud', ubus_methods);
 

feeds/tip/cloud_discovery/files/usr/bin/est_client

@@ -4,6 +4,7 @@
 
 import { ulog_open, ulog, ULOG_SYSLOG, ULOG_STDIO, LOG_DAEMON, LOG_INFO } from 'log';
 import * as fs from 'fs';
+import * as libuci from 'uci';
 
 let store_operational_pem = false;
 let store_operational_ca = false;
@@ -139,6 +140,9 @@ function load_operational_ca() {
 }
 
 function fwtool() {
+	if (!fs.stat('/etc/ucentral/cert.pem'))
+		return 0;
+
 	let pipe = fs.popen(`openssl x509 -in /etc/ucentral/cert.pem -noout -issuer`);
 	let issuer = pipe.read("all");
 	pipe.close();
@@ -163,6 +167,20 @@ function fwtool() {
 	return 0;
 }
 
+function check_cert() {
+	if (!fs.stat('/etc/ucentral/cert.pem'))
+		return 0;
+	let pipe = fs.popen("openssl x509 -in /etc/ucentral/cert.pem  -noout -subject -nameopt multiline | grep commonName | awk '{ print $3 }'");
+	let cn = pipe.read("all");
+	pipe.close();
+	if (!cn)
+		return 0;
+	cn = lc(trim(cn));
+	let uci = libuci.cursor();
+	let serial = uci.get('ucentral', 'config', 'serial');
+	return cn != serial;
+}
+
 switch(ARGV[0]) {
 case 'enroll':
 	let ret = simpleenroll();
@@ -184,4 +202,7 @@ case 'reenroll':
 
 case 'fwtool':
 	exit(fwtool());
+
+case 'check':
+	exit(check_cert());
 }

feeds/ucentral/rrmd/files/usr/share/rrmd/policy_chanutil.uc

@@ -202,7 +202,7 @@ function get_center_channel(channel, band, bw) {
                 "225": 227
             };
         } else if (bw == 80) {
-            bw = {
+            center_channel_map = {
                 "1": 7, "5": 7, "9": 7, "13": 7,
                 "17": 23, "21": 23, "25": 23, "29": 23,
                 "33": 39, "37": 39, "41": 39, "45": 39,
@@ -236,6 +236,8 @@ function get_center_channel(channel, band, bw) {
             };
         } else if (bw == 320) {
             center_channel_map = {
+                "1": 31, "5": 31, "9": 31, "13": 31,
+                "17": 31, "21": 31, "25": 31, "29": 31,
                 "33": 63, "37": 63, "41": 63, "45": 63,
                 "49": 63, "53": 63, "57": 63, "61": 63,
                 "65": 63, "69": 63, "73": 63, "77": 63,
@@ -558,7 +560,7 @@ function random_channel_selection(iface, band, htmode, chan_list_valid) {
     ulog_info(`[%s] Selected channel list from config (default channel list shall be used in case channels haven't been selected) = %s \n`, iface, (chan_list_valid || '[]'));
 
     if (band == '2g' && bw >= 40) {
-        ulog_info(`[%s] It is highly recommended to NOT use %dMHz bandwidth for 2.4G radio \n`, iface, bw);
+        ulog_info(`[%s] It is highly recommended to NOT use %dMHz bandwidth for 2.4G radio (RRM will not work properly) \n`, iface, bw);
     } else if (band == '5g' && bw > 160) {
         ulog_info(`[%s] %dMHz bandwidth not supported for 5G radio. Please use a bandwidth of 160MHz or lower\n`, iface, bw);
     }

feeds/ucentral/rtty/files/rtty.init

@@ -51,7 +51,7 @@ start_rtty() {
 	procd_set_param command $BIN -h $host -I "$id" -a
 	[ -n "$port" ] && procd_append_param command -p "$port"
 	[ -n "$description" ] && procd_append_param command -d "$description"
-	[ "$ssl" = "1" ] && procd_append_param command -s -c /etc/ucentral/cert.pem -k /etc/ucentral/key.pem
+	[ "$ssl" = "1" ] && procd_append_param command -s -c /etc/ucentral/operational.pem -k /etc/ucentral/key.pem
 	[ -n "$token" ] && procd_append_param command -t "$token"
 	[ "$verbose" = "1" ] && procd_append_param command -v
 	[ "$timeout" -eq "0" ] || procd_append_param command -e $timeout

feeds/ucentral/ucentral-client/Makefile

@@ -4,10 +4,10 @@ PKG_NAME:=ucentral-client
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-client.git
-PKG_MIRROR_HASH:=2e28e0aa61b74851c7daf3634ec34d303a603e881e6c5d1fd76c837dea527582
+PKG_MIRROR_HASH:=34c912efa9c0dcdbc6122296e236993484b24b3bc4de51608356304afc8df1c3
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_DATE:=2025-07-08
-PKG_SOURCE_VERSION:=69829f63ea172ce9bd19b7b02073746fe9cf6a52
+PKG_SOURCE_DATE:=2025-07-27
+PKG_SOURCE_VERSION:=c536f6957bd96e57301f9d540b75460119d2a69a
 
 PKG_LICENSE:=BSD-3-Clause
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>

feeds/ucentral/ucentral-client/files/etc/config/ucentral

@@ -6,9 +6,9 @@ config ucentral config
 	option reporting	10
 
 config timeouts timeouts
-	option offline		120
+	option offline		14400
 	option validate		120
-	option orphan		120
+	option orphan		7200
 
 #config event
 #	option type  dhcp

feeds/ucentral/ucentral-schema/Makefile

@@ -4,10 +4,9 @@ PKG_NAME:=ucentral-schema
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-schema.git
-PKG_MIRROR_HASH:=9b12cf94b94688aaf2245742ac1cd3d7a2bccade7e248c47c5f13a3dd7c07401
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_DATE:=2025-07-11
-PKG_SOURCE_VERSION:=b971b73d4cedae6175926373adcdc37a04ced11c
+PKG_SOURCE_DATE:=2025-08-04
+PKG_SOURCE_VERSION:=1c6b3095cb9e398fcbfcb2bf995365066eb76b21
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

feeds/ucentral/ucentral-state/files/ucentral-state

@@ -61,7 +61,7 @@ function self_healing() {
 			heal_wifi = false;
 		}
 
-		if (time_passed_since_rrm < 120) {
+		if (time_passed_since_rrm < 180) {
 			// RRM in progress, do not restart network!
 			ulog(LOG_INFO, 'RRM with Channel utilization may still be in progress, cannot restart network \n');
 			heal_wifi = false;
@@ -265,7 +265,7 @@ let ubus_methods = {
 			current_state = req.args.state;
 			blink_timeout();
 			ulog(LOG_INFO, 'set state -> ' + req.args.state + '\n');
-			
+
 			return state_handler[req.args.state](req.args);
 		},
 		args: {

patches/0095-toolchain-use-older-gcc11-for-legacy-targets.patch

@@ -0,0 +1,37 @@
+From 0b83834085bf536183b0683f4f86800dbe1e2d39 Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Mon, 28 Jul 2025 07:49:07 +0200
+Subject: [PATCH] toolchain: use older gcc11 for legacy targets
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ toolchain/binutils/Config.version | 1 +
+ toolchain/gcc/Config.version      | 1 +
+ 2 files changed, 2 insertions(+)
+
+diff --git a/toolchain/binutils/Config.version b/toolchain/binutils/Config.version
+index c9f8584480..5393d389a5 100644
+--- a/toolchain/binutils/Config.version
++++ b/toolchain/binutils/Config.version
+@@ -1,6 +1,7 @@
+ 
+ config BINUTILS_VERSION_2_37
+ 	bool
++	default y if TARGET_ipq40xx
+ 
+ config BINUTILS_VERSION_2_38
+ 	bool
+diff --git a/toolchain/gcc/Config.version b/toolchain/gcc/Config.version
+index 7126a0c883..b7de3d00e3 100644
+--- a/toolchain/gcc/Config.version
++++ b/toolchain/gcc/Config.version
+@@ -1,5 +1,6 @@
+ config GCC_VERSION_11
+ 	default y if GCC_USE_VERSION_11
++	default y if TARGET_ipq40xx
+ 	bool
+ 
+ config GCC_VERSION_13
+-- 
+2.34.1
+

patches/0096-base-files-boot-add-sync-after-uci-defaults.patch

@@ -0,0 +1,33 @@
+From 309a419087da906a2f3b0f39763f021e9729dd85 Mon Sep 17 00:00:00 2001
+From: Paul White <paul@shasta.cloud>
+Date: Mon, 4 Aug 2025 04:14:23 +0000
+Subject: [PATCH] base-files: boot: add sync after uci-defaults
+
+A scenario was seen where UCI config was not flushed to disk before
+an AP power-cycle after uci-defaults was completed.  Since these
+scripts are deleted after being ran once, there is no way to recover
+without a factory reset.
+
+Adding this sync operation proved to help avoid this situation from
+happening
+
+Signed-off-by: Paul White <paul@shasta.cloud>
+---
+ package/base-files/files/etc/init.d/boot | 1 +
+ 1 file changed, 1 insertion(+)
+
+diff --git a/package/base-files/files/etc/init.d/boot b/package/base-files/files/etc/init.d/boot
+index 15756669a9..c8a803e32c 100755
+--- a/package/base-files/files/etc/init.d/boot
++++ b/package/base-files/files/etc/init.d/boot
+@@ -15,6 +15,7 @@ uci_apply_defaults() {
+ 		( . "./$(basename $file)" ) && rm -f "$file"
+ 	done
+ 	uci commit
++	sync
+ }
+ 
+ boot() {
+-- 
+2.43.0
+

patches/0096-uboot-envtools-add-udaya-id5.patch

@@ -0,0 +1,25 @@
+From d366477af72e725524b47f2fffe8a8c1d500060d Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Thu, 31 Jul 2025 14:45:12 +0200
+Subject: [PATCH] uboot-envtools: add udaya-id5
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ package/boot/uboot-envtools/files/ipq40xx | 1 +
+ 1 file changed, 1 insertion(+)
+
+diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx
+index 8d993fae36..78299195bd 100644
+--- a/package/boot/uboot-envtools/files/ipq40xx
++++ b/package/boot/uboot-envtools/files/ipq40xx
+@@ -42,6 +42,7 @@ luma,wrtq-329acn|\
+ netgear,wac510|\
+ openmesh,a42|\
+ openmesh,a62|\
++udaya,a5-id2|\
+ pakedge,wr-1|\
+ plasmacloud,pa1200|\
+ plasmacloud,pa2200)
+-- 
+2.34.1
+

patches/0097-yuncore_ax820-add-insta1-2-partitions.patch

@@ -0,0 +1,36 @@
+From 3ceb72aaffa13375c049d161702e9d9f55da38c8 Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Mon, 4 Aug 2025 08:34:50 +0200
+Subject: [PATCH] yuncore_ax820: add insta1/2 partitions
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ target/linux/ramips/dts/mt7621_yuncore_ax820.dts | 12 +++++++++++-
+ 1 file changed, 11 insertions(+), 1 deletion(-)
+
+diff --git a/target/linux/ramips/dts/mt7621_yuncore_ax820.dts b/target/linux/ramips/dts/mt7621_yuncore_ax820.dts
+index b2f55b9be0..cc1b59340b 100644
+--- a/target/linux/ramips/dts/mt7621_yuncore_ax820.dts
++++ b/target/linux/ramips/dts/mt7621_yuncore_ax820.dts
+@@ -120,7 +120,17 @@
+ 			partition@90000 {
+ 				compatible = "denx,uimage";
+ 				label = "firmware";
+-				reg = <0x90000 0xf60000>;
++				reg = <0x90000 0xf40000>;
++			};
++
++			partition@fd0000 {
++				label = "insta1";
++				reg = <0xfd0000 0x10000>;
++			};
++
++			partition@fe0000 {
++				label = "insta2";
++				reg = <0xfe0000 0x10000>;
+ 			};
+ 
+ 			partition@ff0000 {
+-- 
+2.34.1
+

patches/0099-wireless-regdb-fix-channel-14-in-JP.patch

@@ -0,0 +1,39 @@
+From d0a0f0304f292a40f2fcdd20b320089627b0f05f Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Thu, 7 Aug 2025 14:50:51 +0200
+Subject: [PATCH] wireless-regdb: fix channel 14 in JP
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ .../patches/200-jp-no-channel-14.patch        | 19 +++++++++++++++++++
+ 1 file changed, 19 insertions(+)
+ create mode 100644 package/firmware/wireless-regdb/patches/200-jp-no-channel-14.patch
+
+diff --git a/package/firmware/wireless-regdb/patches/200-jp-no-channel-14.patch b/package/firmware/wireless-regdb/patches/200-jp-no-channel-14.patch
+new file mode 100644
+index 0000000000..ea1411cfdd
+--- /dev/null
++++ b/package/firmware/wireless-regdb/patches/200-jp-no-channel-14.patch
+@@ -0,0 +1,19 @@
++--- a/db.txt
+++++ b/db.txt
++@@ -16,8 +16,6 @@ country 00:
++ 	(2402 - 2472 @ 40), (20)
++ 	# Channel 12 - 13.
++ 	(2457 - 2482 @ 20), (20), NO-IR, AUTO-BW
++-	# Channel 14. Only JP enables this and for 802.11b only
++-	(2474 - 2494 @ 20), (20), NO-IR, NO-OFDM
++ 	# Channel 36 - 48
++ 	(5170 - 5250 @ 80), (20), AUTO-BW
++ 	# Channel 52 - 64
++@@ -945,7 +943,6 @@ country JO: DFS-JP
++ # https://www.soumu.go.jp/main_content/000833682.pdf
++ country JP: DFS-JP
++ 	(2402 - 2482 @ 40), (20)
++-	(2474 - 2494 @ 20), (20), NO-OFDM
++ 	(4910 - 4990 @ 40), (23)
++ 	(5170 - 5250 @ 80), (20), AUTO-BW
++ 	(5250 - 5330 @ 80), (20), DFS, AUTO-BW
+-- 
+2.34.1
+

profiles/edgecore_spw2ac1200.yml

@@ -0,0 +1,12 @@
+---
+profile: edgecore_spw2ac1200
+target: ipq40xx
+subtarget: generic
+description: Build image for the Edgecore spw2ac1200
+image: bin/targets/ipq40xx/generic/openwrt-ipq40xx-generic-edgecore_spw2ac1200-squashfs-nand-sysupgrade.bin
+packages:
+  - ipq40xx
+include:
+  - ucentral-ap
+  - hostapd
+  - target-ipq40xx

profiles/hfcl_ion4.yml

@@ -0,0 +1,12 @@
+---
+profile: hfcl_ion4
+target: ipq40xx
+subtarget: generic
+description: Build image for the HFCL ION4
+image: bin/targets/ipq40xx/generic/openwrt-ipq40xx-generic-hfcl_ion4-squashfs-nand-sysupgrade.bin
+packages:
+  - ipq40xx
+include:
+  - ucentral-ap
+  - hostapd
+  - target-ipq40xx