Merge pull request #614 from Telecominfraproject/v3.0.0-release

Merge from main

.github/workflows/build-dev.yml

@@ -21,7 +21,7 @@ jobs:
     strategy:
       fail-fast: false
       matrix:
-        target: [ 'cig_wf186w', 'cig_wf188n', 'cig_wf196', 'cig_wf660a', 'cybertan_eww622-a1', 'cybertan_eww631-a1', 'cybertan_eww631-b1', 'edgecore_eap101', 'edgecore_eap102', 'edgecore_eap104', 'edgecore_eap111', 'edgecore_ecw5211', 'edgecore_oap101', 'edgecore_oap101-6e', 'edgecore_oap101e', 'edgecore_oap101e-6e', 'edgecore_oap102', 'hfcl_ion4','hfcl_ion4xi_wp', 'hfcl_ion4xe', 'hfcl_ion4xi', 'hfcl_ion4x', 'hfcl_ion4x_2', 'hfcl_ion4xi_w', 'hfcl_ion4xi_HMR', 'hfcl_ion4x_w', 'indio_um-305ax', 'indio_um-325ac', 'indio_um-510ac-v3', 'indio_um-550ac', 'indio_um-310ax-v1', 'indio_um-510axp-v1', 'indio_um-510axm-v1', 'udaya_a5-id2', 'wallys_dr40x9', 'wallys_dr6018', 'wallys_dr6018_v4', 'yuncore_ax840', 'yuncore_fap640', 'yuncore_fap650', 'yuncore_fap655' ]
+        target: [ 'cig_wf186h', 'cig_wf186w', 'cig_wf188n', 'cig_wf196', 'cig_wf660a', 'cybertan_eww622-a1', 'cybertan_eww631-a1', 'cybertan_eww631-b1', 'edgecore_eap101', 'edgecore_eap102', 'edgecore_eap104', 'edgecore_eap111', 'edgecore_ecw5211', 'edgecore_oap101', 'edgecore_oap101-6e', 'edgecore_oap101e', 'edgecore_oap101e-6e', 'edgecore_oap102', 'hfcl_ion4','hfcl_ion4xi_wp', 'hfcl_ion4xe', 'hfcl_ion4xi', 'hfcl_ion4x', 'hfcl_ion4x_2', 'hfcl_ion4xi_w', 'hfcl_ion4xi_HMR', 'hfcl_ion4x_w', 'indio_um-305ax', 'indio_um-325ac', 'indio_um-510ac-v3', 'indio_um-550ac', 'indio_um-310ax-v1', 'indio_um-510axp-v1', 'indio_um-510axm-v1', 'udaya_a5-id2', 'wallys_dr40x9', 'wallys_dr6018', 'wallys_dr6018_v4', 'yuncore_ax820', 'yuncore_ax840', 'yuncore_fap640', 'yuncore_fap650', 'yuncore_fap655' ]
 
     steps:
     - uses: actions/checkout@v3

feeds/ipq807x/ipq807x/base-files/etc/board.d/02_network

@@ -102,6 +102,13 @@ qcom_setup_interfaces()
 		ucidef_add_switch "switch1" \
 			"6@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
 		;;	
+	optimcloud,d60|\
+ 	optimcloud,d60-5g|\
+ 	optimcloud,d50|\
+ 	optimcloud,d50-5g)
+        ucidef_set_interface_wan "eth0"
+        ucidef_set_interface_lan "eth1"
+        ;;        
 	qcom,ipq5018-mp03.1)
 		ucidef_set_interface_lan "eth1"
 		ucidef_set_interface_wan "eth0"

feeds/ipq807x/ipq807x/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -208,6 +208,10 @@ ath11k/IPQ5018/hw1.0/caldata.bin)
 	liteon,wpx8324|\
 	motorola,q14|\
 	muxi,ap3220l|\
+	optimcloud,d60|\
+ 	optimcloud,d60-5g|\
+ 	optimcloud,d50|\
+ 	optimcloud,d50-5g|\    
 	qcom,ipq5018-mp03.1)
 		caldata_extract "0:ART" 0x1000 0x20000
 		;;
@@ -249,6 +253,10 @@ ath11k/QCN9074/hw1.0/caldata_1.bin)
 	cig,wf196|\
 	wallys,dr6018-v4|\
 	cybertan,eww622-a1|\
+   	optimcloud,d60|\
+ 	optimcloud,d60-5g|\
+ 	optimcloud,d50|\
+ 	optimcloud,d50-5g|\
 	qcom,ipq5018-mp03.1|\
 	qcom,ipq807x-hk14)
 		caldata_extract "0:ART" 0x26800 0x20000
@@ -287,6 +295,10 @@ ath11k-macs)
 	indio,um-310ax-v1|\
 	indio,um-510axp-v1|\
 	indio,um-510axm-v1|\
+	optimcloud,d60|\
+ 	optimcloud,d60-5g|\
+ 	optimcloud,d50|\
+ 	optimcloud,d50-5g|\    
 	cig,wf188n)
 		ath11k_generate_macs
 		;;

feeds/ipq807x/ipq807x/base-files/lib/upgrade/platform.sh

@@ -38,7 +38,7 @@ do_flash_emmc() {
 	local emmcblock=$(find_mmc_part $2)
 	local board_dir=$3
 	local part=$4
-	
+
 	[ -b "$emmcblock" ] || emmcblock=$(find_mmc_part $2)
 
 	[ -z "$emmcblock" ] && {
@@ -162,6 +162,10 @@ platform_check_image() {
 	qcom,ipq6018-cp01|\
 	qcom,ipq807x-hk01|\
 	qcom,ipq807x-hk14|\
+   	optimcloud,d60|\
+ 	optimcloud,d60-5g|\
+ 	optimcloud,d50|\
+ 	optimcloud,d50-5g|\
 	qcom,ipq5018-mp03.3)
 		[ "$magic_long" = "73797375" ] && return 0
 		;;
@@ -200,6 +204,10 @@ platform_do_upgrade() {
 	qcom,ipq6018-cp01|\
 	qcom,ipq807x-hk01|\
 	qcom,ipq807x-hk14|\
+	optimcloud,d60|\
+ 	optimcloud,d60-5g|\
+ 	optimcloud,d50|\
+ 	optimcloud,d50-5g|\
 	qcom,ipq5018-mp03.3|\
 	wallys,dr5018|\
 	wallys,dr6018|\

feeds/ipq807x/ipq807x/files/arch/arm/boot/dts/qcom-ipq5018-optimcloud-d50-5g.dts

@@ -0,0 +1,23 @@
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "../../../arm64/boot/dts/qcom/qcom-ipq5018-optimcloud-d50-5g.dts"
+
+/ {
+	pmuv8: pmu {
+		compatible = "arm,cortex-a7-pmu";
+	};
+};

feeds/ipq807x/ipq807x/files/arch/arm/boot/dts/qcom-ipq5018-optimcloud-d50.dts

@@ -0,0 +1,23 @@
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "../../../arm64/boot/dts/qcom/qcom-ipq5018-optimcloud-d50.dts"
+
+/ {
+	pmuv8: pmu {
+		compatible = "arm,cortex-a7-pmu";
+	};
+};

feeds/ipq807x/ipq807x/files/arch/arm/boot/dts/qcom-ipq5018-optimcloud-d60-5g.dts

@@ -0,0 +1,23 @@
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "../../../arm64/boot/dts/qcom/qcom-ipq5018-optimcloud-d50-5g.dts"
+
+/ {
+	pmuv8: pmu {
+		compatible = "arm,cortex-a7-pmu";
+	};
+};

feeds/ipq807x/ipq807x/files/arch/arm/boot/dts/qcom-ipq5018-optimcloud-d60.dts

@@ -0,0 +1,23 @@
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "../../../arm64/boot/dts/qcom/qcom-ipq5018-optimcloud-d50.dts"
+
+/ {
+	pmuv8: pmu {
+		compatible = "arm,cortex-a7-pmu";
+	};
+};

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-cig-wf186h.dts

@@ -29,6 +29,10 @@
 		serial1 = &blsp1_uart2;
 		ethernet0 = "/soc/dp1";
 		ethernet1 = "/soc/dp2";
+                led-boot = &led_power;
+                led-failsafe = &led_power;
+                led-running = &led_power;
+                led-upgrade = &led_power;
 	};
 
 	chosen {
@@ -682,6 +686,27 @@
 		};
 	};
 
+     leds_pins: leds_pins {
+                led_pwr_g {
+                        pins = "gpio0";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_pwr_b {
+                        pins = "gpio1";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_pwr_r {
+                        pins = "gpio45";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+        };
+
 	i2c_pins: i2c_pins {
 		i2c_scl {
 			pins = "gpio25";
@@ -758,14 +783,31 @@
 };
 
 &soc {
+        leds {
+                compatible = "gpio-leds";
+                pinctrl-0 = <&leds_pins>;
+                pinctrl-names = "default";
 
-	 pwm: pwm@0x1941010 {
-	        pinctrl-0 = <&pwm_pins>;
-	        pinctrl-names = "default";
-	        used-pwm-indices = <1>, <1>, <1>, <1>;
-		dft-pwm-status = <1>, <0>, <0>, <0>;
-	        status = "ok";
+                led3 {
+                        label = "blue:status";
+                        gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+                        linux,default-trigger = "blue-on";
+                        default-state = "off";
+                };
+                led2 {
+                        label = "red:status";
+                        gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+                        linux,default-trigger = "red-on";
+                        default-state = "off";
+                };
+                led_power: led1 {
+                        label = "green:status";
+                        gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+                        linux,default-trigger = "default-on";
+                        default-state = "on";
+                };
         };
+
 };
 
 &usb3 {

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-cig-wf186w.dts

@@ -29,6 +29,10 @@
 		serial1 = &blsp1_uart2;
 		ethernet0 = "/soc/dp1";
 		ethernet1 = "/soc/dp2";
+                led-boot = &led_power;
+                led-failsafe = &led_power;
+                led-running = &led_power;
+                led-upgrade = &led_power;
 	};
 
 	chosen {
@@ -682,6 +686,27 @@
 		};
 	};
 
+     leds_pins: leds_pins {
+                led_pwr_g {
+                        pins = "gpio0";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_pwr_b {
+                        pins = "gpio1";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_pwr_r {
+                        pins = "gpio45";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+        };
+
 	i2c_pins: i2c_pins {
 		i2c_scl {
 			pins = "gpio25";
@@ -758,14 +783,31 @@
 };
 
 &soc {
+        leds {
+                compatible = "gpio-leds";
+                pinctrl-0 = <&leds_pins>;
+                pinctrl-names = "default";
 
-	 pwm: pwm@0x1941010 {
-	        pinctrl-0 = <&pwm_pins>;
-	        pinctrl-names = "default";
-	        used-pwm-indices = <1>, <1>, <1>, <1>;
-		dft-pwm-status = <1>, <0>, <0>, <0>;
-	        status = "ok";
+                led3 {
+                        label = "blue:status";
+                        gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+                        linux,default-trigger = "blue-on";
+                        default-state = "off";
+                };
+                led2 {
+                        label = "red:status";
+                        gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+                        linux,default-trigger = "red-on";
+                        default-state = "off";
+                };
+                led_power: led1 {
+                        label = "green:status";
+                        gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+                        linux,default-trigger = "default-on";
+                        default-state = "on";
+                };
         };
+
 };
 
 &usb3 {

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-optimcloud-d50-5g.dts

@@ -0,0 +1,995 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "qcom-ipq5018.dtsi"
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "OptimCloud D50-5G";
+	compatible = "optimcloud,d50-5g", "qcom,ipq5018-mp03.1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	AUTO_MOUNT;
+	#endif
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp2";
+		ethernet1 = "/soc/dp1";
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+	#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	#endif
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*            256 MB Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          8MB            |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x40800000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          23MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump| 0x4C700000   |          1MB            |
+	 * +--------+--------------+-------------------------+
+	 * | QDSS   | 0x4C800000   |          1MB            |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4C900000  |          17MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4DA00000  |          16MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01700000>;
+		};
+
+		m3_dump@4c700000 {
+			no-map;
+			reg = <0x0 0x4C700000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		qcn9000_pcie0@4c900000 {
+			no-map;
+			reg = <0x0 0x4C900000 0x0 0x01100000>;
+		};
+
+		mhi_region1: dma_pool1@4da00000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4da00000 0x0 0x01000000>;
+		};
+	#elif __IPQ_MEM_PROFILE_512_MB__
+	/*                      512 MB Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          16MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          24MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump|  0x4C800000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  QDSS  |  0x4C900000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * | caldb  |  0x4CA00000  |           2MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4CC00000  |          30MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4EA00000  |          16MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01800000>;
+		};
+
+		m3_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c900000 {
+			no-map;
+			reg = <0x0 0x4c900000 0x0 0x100000>;
+		};
+
+		q6_caldb_region:q6_caldb_region@4ca00000 {
+			no-map;
+			reg = <0x0 0x4ca00000 0x0 0x200000>;
+		};
+
+		qcn9000_pcie0@4cc00000 {
+			no-map;
+			reg = <0x0 0x4CC00000 0x0 0x01E00000>;
+		};
+
+		mhi_region1: dma_pool1@4ea00000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4ea00000 0x0 0x01000000>;
+		};
+	#else
+	/*                      1G Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          16MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          24MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump|  0x4C800000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  QDSS  |  0x4C900000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * | caldb  |  0x4CA00000  |           2MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4CC00000  |          45MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4F900000  |          24MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01800000>;
+		};
+
+		m3_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c900000 {
+			no-map;
+			reg = <0x0 0x4c900000 0x0 0x100000>;
+		};
+
+		q6_caldb_region:q6_caldb_region@4ca00000 {
+			no-map;
+			reg = <0x0 0x4ca00000 0x0 0x200000>;
+		};
+
+		qcn9000_pcie0@4cc00000 {
+			no-map;
+			reg = <0x0 0x4CC00000 0x0 0x02D00000>;
+		};
+
+		mhi_region1: dma_pool1@4F900000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4F900000 0x0 0x01800000>;
+		};
+	#endif
+	};
+
+	soc {
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+			ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x2>;
+			ess-switch@0x39c00000 {
+				compatible = "qcom,ess-switch-ipq50xx";
+				device_id = <0>;
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+					};
+					port@1 {
+						port_id = <2>;
+						forced-speed = <1000>;
+						forced-duplex = <1>;
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+			ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x27>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <1>;
+					};
+					port@2 {
+						port_id = <3>;
+						phy_address = <2>;
+					};
+					port@3 {
+						port_id = <4>;
+						phy_address = <3>;
+					};
+				};
+			};
+		};
+
+		wifi0: wifi@c000000 {
+			qcom,bdf-addr = <0x4BA00000 0x4BA00000 0x4BA00000
+						0x0 0x0>;
+			qcom,caldb-addr = <0x4CA00000 0x4CA00000 0x4CA00000
+						0x0 0x0>;
+			qcom,caldb-size = <0x200000>;
+			status = "ok";
+		};
+
+		ess-uniphy@98000 {
+			status = "disabled";
+		};
+
+		qcom,sps {
+			status = "ok";
+		};
+
+		qcom,usbbam@8B04000 {
+			status = "ok";
+		};
+
+		qcom,diag@0 {
+			status = "ok";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		rpm_etm0 {
+			status = "disabled";
+		};
+
+		lpass: lpass@0xA000000{
+			status = "disabled";
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		pcm_lb: pcm_lb@0 {
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys-polled";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+		poll-interval = <100>;
+
+		button@0 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+		button@1 {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+		
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led@35 {
+			label = "green:4g";
+			gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_5g_wifi";
+			default-state = "off";
+		};
+		led@30 {
+			label = "green:wifi";
+			gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_2g_wifi";
+			default-state = "off";
+		};
+		led@1 {
+			label = "green:internet";
+			gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_voice";
+			default-state = "off";
+		};
+		led@33 {
+			label = "green:lte";
+			gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_lte_g";
+			default-state = "off";
+		};		
+		led@34 {
+			label = "red:lte";
+			gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_lte_r";
+			default-state = "off";
+		};	
+		led@27 {
+			label = "green:mesh";
+			gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_nr_g";
+			default-state = "off";
+		};
+		led@28 {
+			label = "red:mesh";
+			gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_nr_r";
+			default-state = "off";
+		};
+	};
+
+
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: blsp0_uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio23", "gpio25", "gpio24", "gpio26";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+				pins = "gpio9";
+				function = "qspi_clk";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_cs {
+				pins = "gpio8";
+				function = "qspi_cs";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_0 {
+				pins = "gpio7";
+				function = "qspi0";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_1 {
+				pins = "gpio6";
+				function = "qspi1";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_2 {
+				pins = "gpio5";
+				function = "qspi2";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_3 {
+				pins = "gpio4";
+				function = "qspi3";
+				drive-strength = <8>;
+				bias-disable;
+			};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button{
+			pins = "gpio22";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		
+		wps_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		
+	};
+	
+	leds_pins: leds_pins {
+		led_5g_wifi {
+			pins = "gpio35";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_2g_wifi {
+			pins = "gpio30";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_lte_g {
+			pins = "gpio33";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_lte_r {
+			pins = "gpio34";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_nr_g {
+			pins = "gpio27";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_nr_r {
+			pins = "gpio28";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_voice {
+			pins = "gpio1";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};	
+	};
+
+	audio_pins: audio_pinmux {
+		mux_1 {
+			pins = "gpio24";
+			function = "audio_rxbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_2 {
+			pins = "gpio25";
+			function = "audio_rxfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_3 {
+			pins = "gpio26";
+			function = "audio_rxd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_4 {
+			pins = "gpio27";
+			function = "audio_txmclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_5 {
+			pins = "gpio28";
+			function = "audio_txbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_6 {
+			pins = "gpio29";
+			function = "audio_txfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_7 {
+			pins = "gpio30";
+			function = "audio_txd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+};
+
+&usb3 {
+	qcom,multiplexed-phy;
+	qcom,phy-mux-regs = <&tcsr_q6_block 0x2540>;
+	device-power-gpio = <&tlmm 24 1>;
+	status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	status = "disabled";
+	perst-gpio = <&tlmm 18 1>;
+};
+
+&pcie_x2 {
+	status = "ok";
+	perst-gpio = <&tlmm 15 1>;
+};
+
+&bt {
+	status = "ok";
+};
+
+&wcss {
+	status = "ok";
+};
+
+&q6v5_wcss {
+	status = "disabled";
+};
+
+&q6v5_m3 {
+	status = "disabled";
+};
+
+&tcsr_mutex_block {
+	status = "ok";
+};
+
+&tcsr_mutex {
+	status = "ok";
+};
+
+&smem {
+	status = "ok";
+};
+
+&apcs_glb {
+	status = "ok";
+};
+
+&tcsr_q6_block {
+	status = "ok";
+};
+
+&qcom_q6v5_wcss {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_region>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_region>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+	/* IPQ5018 */
+	q6v5_wcss_userpd1 {
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+			<&wcss_smp2p_in 9 0>,
+			<&wcss_smp2p_in 12 0>,
+			<&wcss_smp2p_in 11 0>;
+		interrupt-names ="fatal",
+			"ready",
+			"spawn_ack",
+			"stop-ack";
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+			<&wcss_smp2p_out 9>,
+			<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+			"stop",
+			"spawn";
+		qca,asid = <1>;
+		qca,auto-restart;
+		qca,int_radio;
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&dbm_1p5 {
+	status = "ok";
+};
+
+&msm_imem {
+	status = "ok";
+};
+
+&blsp1_uart1 {
+	status = "ok";
+};
+
+&ssuniphy_0 {
+	status = "ok";
+};
+
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&pcie_x1phy {
+	status = "disabled";
+};
+
+&pcie_x2phy {
+	status = "ok";
+};
+
+&pcie_x1_rp {
+	status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+	status = "ok";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+		qrtr_instance_id = <0x20>;
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+		memory-region = <&mhi_region1>;
+#if !defined(__CNSS2__)
+		base-addr = <0x4CC00000>;
+		m3-dump-addr = <0x4E000000>;
+		etr-addr = <0x4E100000>;
+		qcom,caldb-addr = <0x4E200000>;
+		qcom,tgt-mem-mode = <0x1>;
+		mhi,max-channels = <30>;
+		mhi,timeout = <10000>;
+#endif
+	};
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,board_id = <0x24>;
+	status = "ok";
+};
+
+&wifi3 {
+	/* QCN9000 5G */
+	board_id = <0xa0>;
+	status = "ok";
+};
+
+&qfprom {
+	status = "ok";
+};
+
+&tsens {
+	status = "ok";
+};

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-optimcloud-d50.dts

@@ -0,0 +1,884 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "qcom-ipq5018.dtsi"
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "OptimCloud D50";
+	compatible = "optimcloud,d50", "qcom,ipq5018-mp03.1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	AUTO_MOUNT;
+	#endif
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+	#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	#endif
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*            256 MB Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          8MB            |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x40800000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          23MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump| 0x4C700000   |          1MB            |
+	 * +--------+--------------+-------------------------+
+	 * | QDSS   | 0x4C800000   |          1MB            |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4C900000  |          17MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4DA00000  |          16MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01700000>;
+		};
+
+		m3_dump@4c700000 {
+			no-map;
+			reg = <0x0 0x4C700000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		qcn9000_pcie0@4c900000 {
+			no-map;
+			reg = <0x0 0x4C900000 0x0 0x01100000>;
+		};
+
+		mhi_region1: dma_pool1@4da00000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4da00000 0x0 0x01000000>;
+		};
+	#elif __IPQ_MEM_PROFILE_512_MB__
+	/*                      512 MB Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          16MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          24MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump|  0x4C800000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  QDSS  |  0x4C900000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * | caldb  |  0x4CA00000  |           2MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4CC00000  |          30MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4EA00000  |          16MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01800000>;
+		};
+
+		m3_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c900000 {
+			no-map;
+			reg = <0x0 0x4c900000 0x0 0x100000>;
+		};
+
+		q6_caldb_region:q6_caldb_region@4ca00000 {
+			no-map;
+			reg = <0x0 0x4ca00000 0x0 0x200000>;
+		};
+
+		qcn9000_pcie0@4cc00000 {
+			no-map;
+			reg = <0x0 0x4CC00000 0x0 0x01E00000>;
+		};
+
+		mhi_region1: dma_pool1@4ea00000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4ea00000 0x0 0x01000000>;
+		};
+	#else
+	/*                      1G Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          16MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          24MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump|  0x4C800000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  QDSS  |  0x4C900000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * | caldb  |  0x4CA00000  |           2MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4CC00000  |          45MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4F900000  |          24MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01800000>;
+		};
+
+		m3_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c900000 {
+			no-map;
+			reg = <0x0 0x4c900000 0x0 0x100000>;
+		};
+
+		q6_caldb_region:q6_caldb_region@4ca00000 {
+			no-map;
+			reg = <0x0 0x4ca00000 0x0 0x200000>;
+		};
+
+		qcn9000_pcie0@4cc00000 {
+			no-map;
+			reg = <0x0 0x4CC00000 0x0 0x02D00000>;
+		};
+
+		mhi_region1: dma_pool1@4F900000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4F900000 0x0 0x01800000>;
+		};
+	#endif
+	};
+
+	soc {
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+			ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x2>;
+			ess-switch@0x39c00000 {
+				compatible = "qcom,ess-switch-ipq50xx";
+				device_id = <0>;
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+					};
+					port@1 {
+						port_id = <2>;
+						forced-speed = <1000>;
+						forced-duplex = <1>;
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+			ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x27>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <1>;
+					};
+					port@2 {
+						port_id = <3>;
+						phy_address = <2>;
+					};
+					port@3 {
+						port_id = <4>;
+						phy_address = <3>;
+					};
+				};
+			};
+		};
+
+		wifi0: wifi@c000000 {
+			qcom,bdf-addr = <0x4BA00000 0x4BA00000 0x4BA00000
+						0x0 0x0>;
+			qcom,caldb-addr = <0x4CA00000 0x4CA00000 0x4CA00000
+						0x0 0x0>;
+			qcom,caldb-size = <0x200000>;
+			status = "ok";
+		};
+
+		ess-uniphy@98000 {
+			status = "disabled";
+		};
+
+		qcom,sps {
+			status = "ok";
+		};
+
+		qcom,usbbam@8B04000 {
+			status = "ok";
+		};
+
+		qcom,diag@0 {
+			status = "ok";
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		rpm_etm0 {
+			status = "disabled";
+		};
+
+		lpass: lpass@0xA000000{
+			status = "disabled";
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		pcm_lb: pcm_lb@0 {
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: blsp0_uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio23", "gpio25", "gpio24", "gpio26";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+				pins = "gpio9";
+				function = "qspi_clk";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_cs {
+				pins = "gpio8";
+				function = "qspi_cs";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_0 {
+				pins = "gpio7";
+				function = "qspi0";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_1 {
+				pins = "gpio6";
+				function = "qspi1";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_2 {
+				pins = "gpio5";
+				function = "qspi2";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_3 {
+				pins = "gpio4";
+				function = "qspi3";
+				drive-strength = <8>;
+				bias-disable;
+			};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		wps_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	audio_pins: audio_pinmux {
+		mux_1 {
+			pins = "gpio24";
+			function = "audio_rxbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_2 {
+			pins = "gpio25";
+			function = "audio_rxfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_3 {
+			pins = "gpio26";
+			function = "audio_rxd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_4 {
+			pins = "gpio27";
+			function = "audio_txmclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_5 {
+			pins = "gpio28";
+			function = "audio_txbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_6 {
+			pins = "gpio29";
+			function = "audio_txfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_7 {
+			pins = "gpio30";
+			function = "audio_txd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+};
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&usb3 {
+	qcom,multiplexed-phy;
+	qcom,phy-mux-regs = <&tcsr_q6_block 0x2540>;
+	device-power-gpio = <&tlmm 24 1>;
+	status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	status = "disabled";
+	perst-gpio = <&tlmm 18 1>;
+};
+
+&pcie_x2 {
+	status = "ok";
+	perst-gpio = <&tlmm 15 1>;
+};
+
+&bt {
+	status = "ok";
+};
+
+&wcss {
+	status = "ok";
+};
+
+&q6v5_wcss {
+	status = "disabled";
+};
+
+&q6v5_m3 {
+	status = "disabled";
+};
+
+&tcsr_mutex_block {
+	status = "ok";
+};
+
+&tcsr_mutex {
+	status = "ok";
+};
+
+&smem {
+	status = "ok";
+};
+
+&apcs_glb {
+	status = "ok";
+};
+
+&tcsr_q6_block {
+	status = "ok";
+};
+
+&qcom_q6v5_wcss {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_region>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_region>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+	/* IPQ5018 */
+	q6v5_wcss_userpd1 {
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+			<&wcss_smp2p_in 9 0>,
+			<&wcss_smp2p_in 12 0>,
+			<&wcss_smp2p_in 11 0>;
+		interrupt-names ="fatal",
+			"ready",
+			"spawn_ack",
+			"stop-ack";
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+			<&wcss_smp2p_out 9>,
+			<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+			"stop",
+			"spawn";
+		qca,asid = <1>;
+		qca,auto-restart;
+		qca,int_radio;
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&dbm_1p5 {
+	status = "ok";
+};
+
+&msm_imem {
+	status = "ok";
+};
+
+&blsp1_uart1 {
+	status = "ok";
+};
+
+&ssuniphy_0 {
+	status = "ok";
+};
+
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&pcie_x1phy {
+	status = "disabled";
+};
+
+&pcie_x2phy {
+	status = "ok";
+};
+
+&pcie_x1_rp {
+	status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+	status = "ok";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+		qrtr_instance_id = <0x20>;
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+		memory-region = <&mhi_region1>;
+#if !defined(__CNSS2__)
+		base-addr = <0x4CC00000>;
+		m3-dump-addr = <0x4E000000>;
+		etr-addr = <0x4E100000>;
+		qcom,caldb-addr = <0x4E200000>;
+		qcom,tgt-mem-mode = <0x1>;
+		mhi,max-channels = <30>;
+		mhi,timeout = <10000>;
+#endif
+	};
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,board_id = <0x24>;
+	status = "ok";
+};
+
+&wifi3 {
+	/* QCN9000 5G */
+	board_id = <0xa0>;
+	status = "ok";
+};
+
+&qfprom {
+	status = "ok";
+};
+
+&tsens {
+	status = "ok";
+};

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-optimcloud-d60-5g.dts

@@ -0,0 +1,995 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "qcom-ipq5018.dtsi"
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "OptimCloud D60-5G";
+	compatible = "optimcloud,d60-5g", "qcom,ipq5018-mp03.1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	AUTO_MOUNT;
+	#endif
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp2";
+		ethernet1 = "/soc/dp1";
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+	#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	#endif
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*            256 MB Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          8MB            |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x40800000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          23MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump| 0x4C700000   |          1MB            |
+	 * +--------+--------------+-------------------------+
+	 * | QDSS   | 0x4C800000   |          1MB            |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4C900000  |          17MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4DA00000  |          16MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01700000>;
+		};
+
+		m3_dump@4c700000 {
+			no-map;
+			reg = <0x0 0x4C700000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		qcn9000_pcie0@4c900000 {
+			no-map;
+			reg = <0x0 0x4C900000 0x0 0x01100000>;
+		};
+
+		mhi_region1: dma_pool1@4da00000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4da00000 0x0 0x01000000>;
+		};
+	#elif __IPQ_MEM_PROFILE_512_MB__
+	/*                      512 MB Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          16MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          24MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump|  0x4C800000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  QDSS  |  0x4C900000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * | caldb  |  0x4CA00000  |           2MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4CC00000  |          30MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4EA00000  |          16MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01800000>;
+		};
+
+		m3_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c900000 {
+			no-map;
+			reg = <0x0 0x4c900000 0x0 0x100000>;
+		};
+
+		q6_caldb_region:q6_caldb_region@4ca00000 {
+			no-map;
+			reg = <0x0 0x4ca00000 0x0 0x200000>;
+		};
+
+		qcn9000_pcie0@4cc00000 {
+			no-map;
+			reg = <0x0 0x4CC00000 0x0 0x01E00000>;
+		};
+
+		mhi_region1: dma_pool1@4ea00000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4ea00000 0x0 0x01000000>;
+		};
+	#else
+	/*                      1G Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          16MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          24MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump|  0x4C800000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  QDSS  |  0x4C900000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * | caldb  |  0x4CA00000  |           2MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4CC00000  |          45MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4F900000  |          24MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01800000>;
+		};
+
+		m3_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c900000 {
+			no-map;
+			reg = <0x0 0x4c900000 0x0 0x100000>;
+		};
+
+		q6_caldb_region:q6_caldb_region@4ca00000 {
+			no-map;
+			reg = <0x0 0x4ca00000 0x0 0x200000>;
+		};
+
+		qcn9000_pcie0@4cc00000 {
+			no-map;
+			reg = <0x0 0x4CC00000 0x0 0x02D00000>;
+		};
+
+		mhi_region1: dma_pool1@4F900000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4F900000 0x0 0x01800000>;
+		};
+	#endif
+	};
+
+	soc {
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+			ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x2>;
+			ess-switch@0x39c00000 {
+				compatible = "qcom,ess-switch-ipq50xx";
+				device_id = <0>;
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+					};
+					port@1 {
+						port_id = <2>;
+						forced-speed = <1000>;
+						forced-duplex = <1>;
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+			ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x27>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <1>;
+					};
+					port@2 {
+						port_id = <3>;
+						phy_address = <2>;
+					};
+					port@3 {
+						port_id = <4>;
+						phy_address = <3>;
+					};
+				};
+			};
+		};
+
+		wifi0: wifi@c000000 {
+			qcom,bdf-addr = <0x4BA00000 0x4BA00000 0x4BA00000
+						0x0 0x0>;
+			qcom,caldb-addr = <0x4CA00000 0x4CA00000 0x4CA00000
+						0x0 0x0>;
+			qcom,caldb-size = <0x200000>;
+			status = "ok";
+		};
+
+		ess-uniphy@98000 {
+			status = "disabled";
+		};
+
+		qcom,sps {
+			status = "ok";
+		};
+
+		qcom,usbbam@8B04000 {
+			status = "ok";
+		};
+
+		qcom,diag@0 {
+			status = "ok";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		rpm_etm0 {
+			status = "disabled";
+		};
+
+		lpass: lpass@0xA000000{
+			status = "disabled";
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		pcm_lb: pcm_lb@0 {
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys-polled";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+		poll-interval = <100>;
+
+		button@0 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+		button@1 {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+		
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led@35 {
+			label = "green:4g";
+			gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_5g_wifi";
+			default-state = "off";
+		};
+		led@30 {
+			label = "green:wifi";
+			gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_2g_wifi";
+			default-state = "off";
+		};
+		led@1 {
+			label = "green:internet";
+			gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_voice";
+			default-state = "off";
+		};
+		led@33 {
+			label = "green:lte";
+			gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_lte_g";
+			default-state = "off";
+		};		
+		led@34 {
+			label = "red:lte";
+			gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_lte_r";
+			default-state = "off";
+		};	
+		led@27 {
+			label = "green:mesh";
+			gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_nr_g";
+			default-state = "off";
+		};
+		led@28 {
+			label = "red:mesh";
+			gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "led_nr_r";
+			default-state = "off";
+		};
+	};
+
+
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: blsp0_uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio23", "gpio25", "gpio24", "gpio26";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+				pins = "gpio9";
+				function = "qspi_clk";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_cs {
+				pins = "gpio8";
+				function = "qspi_cs";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_0 {
+				pins = "gpio7";
+				function = "qspi0";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_1 {
+				pins = "gpio6";
+				function = "qspi1";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_2 {
+				pins = "gpio5";
+				function = "qspi2";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_3 {
+				pins = "gpio4";
+				function = "qspi3";
+				drive-strength = <8>;
+				bias-disable;
+			};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button{
+			pins = "gpio22";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		
+		wps_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		
+	};
+	
+	leds_pins: leds_pins {
+		led_5g_wifi {
+			pins = "gpio35";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_2g_wifi {
+			pins = "gpio30";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_lte_g {
+			pins = "gpio33";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_lte_r {
+			pins = "gpio34";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_nr_g {
+			pins = "gpio27";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_nr_r {
+			pins = "gpio28";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_voice {
+			pins = "gpio1";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};	
+	};
+
+	audio_pins: audio_pinmux {
+		mux_1 {
+			pins = "gpio24";
+			function = "audio_rxbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_2 {
+			pins = "gpio25";
+			function = "audio_rxfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_3 {
+			pins = "gpio26";
+			function = "audio_rxd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_4 {
+			pins = "gpio27";
+			function = "audio_txmclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_5 {
+			pins = "gpio28";
+			function = "audio_txbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_6 {
+			pins = "gpio29";
+			function = "audio_txfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_7 {
+			pins = "gpio30";
+			function = "audio_txd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+};
+
+&usb3 {
+	qcom,multiplexed-phy;
+	qcom,phy-mux-regs = <&tcsr_q6_block 0x2540>;
+	device-power-gpio = <&tlmm 24 1>;
+	status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	status = "disabled";
+	perst-gpio = <&tlmm 18 1>;
+};
+
+&pcie_x2 {
+	status = "ok";
+	perst-gpio = <&tlmm 15 1>;
+};
+
+&bt {
+	status = "ok";
+};
+
+&wcss {
+	status = "ok";
+};
+
+&q6v5_wcss {
+	status = "disabled";
+};
+
+&q6v5_m3 {
+	status = "disabled";
+};
+
+&tcsr_mutex_block {
+	status = "ok";
+};
+
+&tcsr_mutex {
+	status = "ok";
+};
+
+&smem {
+	status = "ok";
+};
+
+&apcs_glb {
+	status = "ok";
+};
+
+&tcsr_q6_block {
+	status = "ok";
+};
+
+&qcom_q6v5_wcss {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_region>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_region>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+	/* IPQ5018 */
+	q6v5_wcss_userpd1 {
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+			<&wcss_smp2p_in 9 0>,
+			<&wcss_smp2p_in 12 0>,
+			<&wcss_smp2p_in 11 0>;
+		interrupt-names ="fatal",
+			"ready",
+			"spawn_ack",
+			"stop-ack";
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+			<&wcss_smp2p_out 9>,
+			<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+			"stop",
+			"spawn";
+		qca,asid = <1>;
+		qca,auto-restart;
+		qca,int_radio;
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&dbm_1p5 {
+	status = "ok";
+};
+
+&msm_imem {
+	status = "ok";
+};
+
+&blsp1_uart1 {
+	status = "ok";
+};
+
+&ssuniphy_0 {
+	status = "ok";
+};
+
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&pcie_x1phy {
+	status = "disabled";
+};
+
+&pcie_x2phy {
+	status = "ok";
+};
+
+&pcie_x1_rp {
+	status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+	status = "ok";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+		qrtr_instance_id = <0x20>;
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+		memory-region = <&mhi_region1>;
+#if !defined(__CNSS2__)
+		base-addr = <0x4CC00000>;
+		m3-dump-addr = <0x4E000000>;
+		etr-addr = <0x4E100000>;
+		qcom,caldb-addr = <0x4E200000>;
+		qcom,tgt-mem-mode = <0x1>;
+		mhi,max-channels = <30>;
+		mhi,timeout = <10000>;
+#endif
+	};
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,board_id = <0x24>;
+	status = "ok";
+};
+
+&wifi3 {
+	/* QCN9000 5G */
+	board_id = <0xa0>;
+	status = "ok";
+};
+
+&qfprom {
+	status = "ok";
+};
+
+&tsens {
+	status = "ok";
+};

feeds/ipq807x/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-optimcloud-d60.dts

@@ -0,0 +1,884 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "qcom-ipq5018.dtsi"
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "OptimCloud D60";
+	compatible = "optimcloud,d60", "qcom,ipq5018-mp03.1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	AUTO_MOUNT;
+	#endif
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+	#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	#endif
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*            256 MB Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          8MB            |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x40800000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          23MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump| 0x4C700000   |          1MB            |
+	 * +--------+--------------+-------------------------+
+	 * | QDSS   | 0x4C800000   |          1MB            |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4C900000  |          17MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4DA00000  |          16MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01700000>;
+		};
+
+		m3_dump@4c700000 {
+			no-map;
+			reg = <0x0 0x4C700000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		qcn9000_pcie0@4c900000 {
+			no-map;
+			reg = <0x0 0x4C900000 0x0 0x01100000>;
+		};
+
+		mhi_region1: dma_pool1@4da00000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4da00000 0x0 0x01000000>;
+		};
+	#elif __IPQ_MEM_PROFILE_512_MB__
+	/*                      512 MB Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          16MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          24MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump|  0x4C800000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  QDSS  |  0x4C900000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * | caldb  |  0x4CA00000  |           2MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4CC00000  |          30MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4EA00000  |          16MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01800000>;
+		};
+
+		m3_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c900000 {
+			no-map;
+			reg = <0x0 0x4c900000 0x0 0x100000>;
+		};
+
+		q6_caldb_region:q6_caldb_region@4ca00000 {
+			no-map;
+			reg = <0x0 0x4ca00000 0x0 0x200000>;
+		};
+
+		qcn9000_pcie0@4cc00000 {
+			no-map;
+			reg = <0x0 0x4CC00000 0x0 0x01E00000>;
+		};
+
+		mhi_region1: dma_pool1@4ea00000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4ea00000 0x0 0x01000000>;
+		};
+	#else
+	/*                      1G Profile
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |  NSS   |  0x40000000  |          16MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  | Depends on total memory |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * | uboot  |  0x4A600000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |  SBL   |  0x4AA00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  smem  |  0x4AB00000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |   TZ   |  0x4AC00000  |           4MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |   Q6   |  0x4B000000  |          24MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | M3 Dump|  0x4C800000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * |  QDSS  |  0x4C900000  |           1MB           |
+	 * +--------+--------------+-------------------------+
+	 * | caldb  |  0x4CA00000  |           2MB           |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |QCN9000 |  0x4CC00000  |          45MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |  MHI1  |  0x4F900000  |          24MB           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |                                                 |
+	 * |      Rest of the memory for Linux               |
+	 * |                                                 |
+	 * +=================================================+
+	 */
+		q6_region: wcnss@4b000000 {
+			no-map;
+			reg = <0x0 0x4b000000 0x0 0x01800000>;
+		};
+
+		m3_dump@4c800000 {
+			no-map;
+			reg = <0x0 0x4c800000 0x0 0x100000>;
+		};
+
+		q6_etr_region:q6_etr_dump@4c900000 {
+			no-map;
+			reg = <0x0 0x4c900000 0x0 0x100000>;
+		};
+
+		q6_caldb_region:q6_caldb_region@4ca00000 {
+			no-map;
+			reg = <0x0 0x4ca00000 0x0 0x200000>;
+		};
+
+		qcn9000_pcie0@4cc00000 {
+			no-map;
+			reg = <0x0 0x4CC00000 0x0 0x02D00000>;
+		};
+
+		mhi_region1: dma_pool1@4F900000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4F900000 0x0 0x01800000>;
+		};
+	#endif
+	};
+
+	soc {
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+			ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x2>;
+			ess-switch@0x39c00000 {
+				compatible = "qcom,ess-switch-ipq50xx";
+				device_id = <0>;
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+					};
+					port@1 {
+						port_id = <2>;
+						forced-speed = <1000>;
+						forced-duplex = <1>;
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+			ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x27>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <1>;
+					};
+					port@2 {
+						port_id = <3>;
+						phy_address = <2>;
+					};
+					port@3 {
+						port_id = <4>;
+						phy_address = <3>;
+					};
+				};
+			};
+		};
+
+		wifi0: wifi@c000000 {
+			qcom,bdf-addr = <0x4BA00000 0x4BA00000 0x4BA00000
+						0x0 0x0>;
+			qcom,caldb-addr = <0x4CA00000 0x4CA00000 0x4CA00000
+						0x0 0x0>;
+			qcom,caldb-size = <0x200000>;
+			status = "ok";
+		};
+
+		ess-uniphy@98000 {
+			status = "disabled";
+		};
+
+		qcom,sps {
+			status = "ok";
+		};
+
+		qcom,usbbam@8B04000 {
+			status = "ok";
+		};
+
+		qcom,diag@0 {
+			status = "ok";
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		rpm_etm0 {
+			status = "disabled";
+		};
+
+		lpass: lpass@0xA000000{
+			status = "disabled";
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		pcm_lb: pcm_lb@0 {
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: blsp0_uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio23", "gpio25", "gpio24", "gpio26";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+				pins = "gpio9";
+				function = "qspi_clk";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_cs {
+				pins = "gpio8";
+				function = "qspi_cs";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_0 {
+				pins = "gpio7";
+				function = "qspi0";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_1 {
+				pins = "gpio6";
+				function = "qspi1";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_2 {
+				pins = "gpio5";
+				function = "qspi2";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		qspi_data_3 {
+				pins = "gpio4";
+				function = "qspi3";
+				drive-strength = <8>;
+				bias-disable;
+			};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		wps_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	audio_pins: audio_pinmux {
+		mux_1 {
+			pins = "gpio24";
+			function = "audio_rxbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_2 {
+			pins = "gpio25";
+			function = "audio_rxfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_3 {
+			pins = "gpio26";
+			function = "audio_rxd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_4 {
+			pins = "gpio27";
+			function = "audio_txmclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_5 {
+			pins = "gpio28";
+			function = "audio_txbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_6 {
+			pins = "gpio29";
+			function = "audio_txfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_7 {
+			pins = "gpio30";
+			function = "audio_txd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+};
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&usb3 {
+	qcom,multiplexed-phy;
+	qcom,phy-mux-regs = <&tcsr_q6_block 0x2540>;
+	device-power-gpio = <&tlmm 24 1>;
+	status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	status = "disabled";
+	perst-gpio = <&tlmm 18 1>;
+};
+
+&pcie_x2 {
+	status = "ok";
+	perst-gpio = <&tlmm 15 1>;
+};
+
+&bt {
+	status = "ok";
+};
+
+&wcss {
+	status = "ok";
+};
+
+&q6v5_wcss {
+	status = "disabled";
+};
+
+&q6v5_m3 {
+	status = "disabled";
+};
+
+&tcsr_mutex_block {
+	status = "ok";
+};
+
+&tcsr_mutex {
+	status = "ok";
+};
+
+&smem {
+	status = "ok";
+};
+
+&apcs_glb {
+	status = "ok";
+};
+
+&tcsr_q6_block {
+	status = "ok";
+};
+
+&qcom_q6v5_wcss {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_region>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_region>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+	/* IPQ5018 */
+	q6v5_wcss_userpd1 {
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+			<&wcss_smp2p_in 9 0>,
+			<&wcss_smp2p_in 12 0>,
+			<&wcss_smp2p_in 11 0>;
+		interrupt-names ="fatal",
+			"ready",
+			"spawn_ack",
+			"stop-ack";
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+			<&wcss_smp2p_out 9>,
+			<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+			"stop",
+			"spawn";
+		qca,asid = <1>;
+		qca,auto-restart;
+		qca,int_radio;
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&dbm_1p5 {
+	status = "ok";
+};
+
+&msm_imem {
+	status = "ok";
+};
+
+&blsp1_uart1 {
+	status = "ok";
+};
+
+&ssuniphy_0 {
+	status = "ok";
+};
+
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&pcie_x1phy {
+	status = "disabled";
+};
+
+&pcie_x2phy {
+	status = "ok";
+};
+
+&pcie_x1_rp {
+	status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+	status = "ok";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+		qrtr_instance_id = <0x20>;
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+		memory-region = <&mhi_region1>;
+#if !defined(__CNSS2__)
+		base-addr = <0x4CC00000>;
+		m3-dump-addr = <0x4E000000>;
+		etr-addr = <0x4E100000>;
+		qcom,caldb-addr = <0x4E200000>;
+		qcom,tgt-mem-mode = <0x1>;
+		mhi,max-channels = <30>;
+		mhi,timeout = <10000>;
+#endif
+	};
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,board_id = <0x24>;
+	status = "ok";
+};
+
+&wifi3 {
+	/* QCN9000 5G */
+	board_id = <0xa0>;
+	status = "ok";
+};
+
+&qfprom {
+	status = "ok";
+};
+
+&tsens {
+	status = "ok";
+};

feeds/ipq807x/ipq807x/image/ipq50xx.mk

@@ -165,3 +165,56 @@ define Device/yuncore_fap655
 endef
 TARGET_DEVICES += yuncore_fap655
 
+define Device/optimcloud_d50-5g
+   DEVICE_TITLE := OptimCloud D50-5G
+   DEVICE_DTS := qcom-ipq5018-optimcloud-d50-5g
+   SUPPORTED_DEVICES := optimcloud,d50-5g
+   DEVICE_PACKAGES := ath11k-wifi-optimcloud-d50 ath11k-firmware-ipq50xx ath11k-firmware-qcn9000 
+   DEVICE_DTS_CONFIG := config@mp03.1
+   IMAGES := sysupgrade.tar nand-factory.bin nand-factory.ubi
+   IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
+   IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
+   IMAGE/nand-factory.ubi := append-ubi
+endef
+TARGET_DEVICES += optimcloud_d50-5g
+ 
+define Device/optimcloud_d50
+   DEVICE_TITLE := OptimCloud D50
+   DEVICE_DTS := qcom-ipq5018-optimcloud-d50
+   SUPPORTED_DEVICES := optimcloud,d50
+   DEVICE_PACKAGES := ath11k-wifi-optimcloud-d50 ath11k-firmware-ipq50xx ath11k-firmware-qcn9000 ath11k-firmware-qcn6122
+   DEVICE_DTS_CONFIG := config@mp03.1
+   IMAGES := sysupgrade.tar nand-factory.bin nand-factory.ubi
+   IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
+   IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
+   IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand
+   IMAGE/nand-factory.ubi := append-ubi | qsdk-ipq-factory-nand
+endef
+TARGET_DEVICES += optimcloud_d50
+ 
+define Device/optimcloud_d60-5g
+   DEVICE_TITLE := OptimCloud D60-5G
+   DEVICE_DTS := qcom-ipq5018-optimcloud-d60-5g
+   SUPPORTED_DEVICES := optimcloud,d60-5g
+   DEVICE_PACKAGES := ath11k-wifi-optimcloud-d60 ath11k-firmware-ipq50xx ath11k-firmware-qcn9000
+   DEVICE_DTS_CONFIG := config@mp03.1
+   IMAGES := sysupgrade.tar nand-factory.bin nand-factory.ubi
+   IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
+   IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
+   IMAGE/nand-factory.ubi := append-ubi
+endef
+TARGET_DEVICES += optimcloud_d60-5g
+ 
+define Device/optimcloud_d60
+   DEVICE_TITLE := OptimCloud D60
+   DEVICE_DTS := qcom-ipq5018-optimcloud-d60
+   SUPPORTED_DEVICES := optimcloud,d60
+   DEVICE_PACKAGES := ath11k-wifi-optimcloud-d60 ath11k-firmware-ipq50xx ath11k-firmware-qcn9000 ath11k-firmware-qcn6122
+   DEVICE_DTS_CONFIG := config@mp03.1
+   IMAGES := sysupgrade.tar nand-factory.bin nand-factory.ubi
+   IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
+   IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
+   IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand
+   IMAGE/nand-factory.ubi := append-ubi | qsdk-ipq-factory-nand
+ endef
+ TARGET_DEVICES += optimcloud_d60

feeds/ipq807x_v5.4/hostapd/files/hostapd.sh

@@ -745,11 +745,11 @@ hostapd_set_bss_options() {
 	}
 
 	case "$auth_type" in
-		sae|owe|eap192|eap256)
+		sae|owe|eap192|eap2)
 			set_default ieee80211w 2
 			set_default sae_require_mfp 1
 		;;
-		psk-sae|psk2-radius|eap-eap256)
+		psk-sae|psk2-radius|eap-eap2)
 			set_default ieee80211w 1
 			set_default sae_require_mfp 1
 		;;
@@ -796,7 +796,7 @@ hostapd_set_bss_options() {
 			vlan_possible=1
 			wps_possible=1
 		;;
-		eap|eap192|eap-eap256|eap256)
+		eap|eap192|eap-eap2|eap2)
 			append_radius_server
 			# radius can provide VLAN ID for clients
 			vlan_possible=1
@@ -1342,10 +1342,10 @@ wpa_supplicant_add_network() {
 		default_disabled
 
 	case "$auth_type" in
-		sae|owe|eap-eap256)
+		sae|owe|eap-eap2)
 			set_default ieee80211w 2
 		;;
-		psk-sae|eap192|eap256)
+		psk-sae|eap192|eap2)
 			set_default ieee80211w 1
 		;;
 	esac
@@ -1423,7 +1423,7 @@ wpa_supplicant_add_network() {
 			fi
 			append network_data "$passphrase" "$N$T"
 		;;
-		eap|eap192|eap-eap256|eap256)
+		eap|eap192|eap-eap2|eap2)
 			hostapd_append_wpa_key_mgmt
 			key_mgmt="$wpa_key_mgmt"
 

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/board.d/01_leds

@@ -18,6 +18,7 @@ edgecore,oap101e|\
 edgecore,oap101e-6e)
 	ucidef_set_led_netdev "wan" "wan" "red:ethernet" "eth1"
 	;;
+hfcl,ion4x_w|\
 hfcl,ion4xi_w)
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "blue:wifi5" "phy0tpt"
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "blue:wifi2" "phy1tpt"

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/board.d/02_network

@@ -30,6 +30,7 @@ qcom_setup_interfaces()
 		ucidef_add_switch "switch1" \
 			"6@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
 		;;
+	hfcl,ion4x_w|\
 	hfcl,ion4xi_w)
 		ucidef_set_interface_wan "eth0"
 		;;

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -69,6 +69,7 @@ ath11k/IPQ5018/hw1.0/caldata.bin)
 	edgecore,oap101-6e|\
 	edgecore,oap101e|\
 	edgecore,oap101e-6e|\
+	hfcl,ion4x_w|\
 	hfcl,ion4xi_w|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
@@ -126,6 +127,7 @@ ath11k-macs)
 	yuncore,fap655)
 		ath11k_generate_macs
 		;;
+	hfcl,ion4x_w|\
 	hfcl,ion4xi_w)
 		ath11k_generate_macs_ion4x
 		;;

feeds/ipq807x_v5.4/ipq50xx/base-files/lib/upgrade/platform.sh

@@ -71,6 +71,7 @@ platform_check_image() {
 	cig,wf186w|\
 	cig,wf186h|\
 	edgecore,eap104|\
+	hfcl,ion4x_w|\
 	hfcl,ion4xi_w|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
@@ -103,7 +104,8 @@ platform_do_upgrade() {
 		[ "$(find_mtd_chardev rootfs)" ] && CI_UBIPART="rootfs"
 		nand_upgrade_tar "$1"
 		;;
-        hfcl,ion4xi_w)
+        hfcl,ion4x_w|\
+	hfcl,ion4xi_w)
                 wp_part=$(fw_printenv primary | cut  -d = -f2)
                 echo "Current Primary is $wp_part"
                 if [[ $wp_part == 1 ]]; then

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-cig-wf186h.dts

@@ -31,6 +31,10 @@
 		serial1 = &blsp1_uart2;
 		ethernet0 = "/soc/dp1";
 		ethernet1 = "/soc/dp2";
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
 	};
 
 	chosen {
@@ -568,15 +572,31 @@
 };
 
 &soc {
-         pwm: pwm@0x1941010 {
-                pinctrl-0 = <&pwm_pins>;
-                pinctrl-names = "default";
-                used-pwm-indices = <1>, <1>, <1>, <1>;
-                dft-pwm-status = <1>, <0>, <0>, <0>;
-                status = "ok";
-        };
-};
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
 
+		led3 {
+			label = "blue:status";
+			gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "blue-on";
+			default-state = "off";
+		};
+		led2 {
+			label = "red:status";
+			gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "red-on";
+			default-state = "off";
+		};
+		led_power: led1 {
+			label = "green:status";
+			gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+			default-state = "on";
+		};
+	};
+};
 
 &tlmm {
 	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
@@ -680,6 +700,27 @@
 		};
 	};
 
+	leds_pins: leds_pins {
+		led_pwr_g {
+			pins = "gpio0";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_pwr_b {
+			pins = "gpio1";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_pwr_r {
+			pins = "gpio45";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
 	audio_pins: audio_pinmux {
 		mux_1 {
 			pins = "gpio24";

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-cig-wf186w.dts

@@ -31,6 +31,10 @@
 		serial1 = &blsp1_uart2;
 		ethernet0 = "/soc/dp1";
 		ethernet1 = "/soc/dp2";
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
 	};
 
 	chosen {
@@ -568,15 +572,31 @@
 };
 
 &soc {
-         pwm: pwm@0x1941010 {
-                pinctrl-0 = <&pwm_pins>;
-                pinctrl-names = "default";
-                used-pwm-indices = <1>, <1>, <1>, <1>;
-                dft-pwm-status = <1>, <0>, <0>, <0>;
-                status = "ok";
-        };
-};
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
 
+		led3 {
+			label = "blue:status";
+			gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "blue-on";
+			default-state = "off";
+		};
+		led2 {
+			label = "red:status";
+			gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "red-on";
+			default-state = "off";
+		};
+		led_power: led1 {
+			label = "green:status";
+			gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+			default-state = "on";
+		};
+	};
+};
 
 &tlmm {
 	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
@@ -680,6 +700,27 @@
 		};
 	};
 
+	leds_pins: leds_pins {
+		led_pwr_g {
+			pins = "gpio0";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_pwr_b {
+			pins = "gpio1";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+		led_pwr_r {
+			pins = "gpio45";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
 	audio_pins: audio_pinmux {
 		mux_1 {
 			pins = "gpio24";

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-hfcl-ion4x_w.dts

@@ -0,0 +1,852 @@
+/dts-v1/;
+/* Copyright (c) 2018-2021, The Linux Foundation. All rights reserved.
+ *
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "ipq5018.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "HFCL ION4x_w";
+	compatible = "hfcl,ion4x_w", "qcom,ipq5018-mp03.3", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*		   256 MB Profile
+	 * +==========+==============+=========================+
+	 * |	  |	      |			 |
+	 * |  Region  | Start Offset |	  Size	   |
+	 * |	  |	      |			 |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |	   8MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x40800000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |	   4MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |	   4MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |	      |			 |
+	 * |   code/  |  0x4B000000  |	  20MB	   |
+	 * |   data   |	      |			 |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |	      |			 |
+	 * |   data   |  0x4C400000  |	  13MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |	      |			 |
+	 * |  M3 Dump |  0x4D100000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |	      |			 |
+	 * |   QDSS   |  0x4D200000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|	      |			 |
+	 * |   data   |  0x4D300000  |	  13MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|	      |			 |
+	 * |  M3 Dump |  0x4E000000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|	      |			 |
+	 * |   QDSS   |  0x4E100000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|	      |			 |
+	 * |   data   |  0x4E200000  |	  13MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|	      |			 |
+	 * |  M3 Dump |  0x4EF00000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|	      |			 |
+	 * |   QDSS   |  0x4F000000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |						   |
+	 * |	    Rest of the memory for Linux	   |
+	 * |						   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x4100000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x1400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xD00000>;
+		};
+
+		m3_dump: m3_dump@4D100000 {
+			no-map;
+			reg = <0x0 0x4D100000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0xD00000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E000000 {
+			no-map;
+			reg = <0x0 0x4E000000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E100000 {
+			no-map;
+			reg = <0x0 0x4E100000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E200000 {
+			no-map;
+			reg = <0x0 0x4E200000 0x0 0xD00000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4EF00000 {
+			no-map;
+			reg = <0x0 0x4EF00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F000000 {
+			no-map;
+			reg = <0x0 0x4F000000 0x0 0x100000>;
+		};
+	#else
+	/*		 512MB/1GB Profiles
+	 * +==========+==============+=========================+
+	 * |	  |	      |			 |
+	 * |  Region  | Start Offset |	  Size	   |
+	 * |	  |	      |			 |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |	  16MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x41000000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |	   4MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |	   4MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |	      |			 |
+	 * |   code/  |  0x4B000000  |	  20MB	   |
+	 * |   data   |	      |			 |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |	      |			 |
+	 * |   data   |  0x4C400000  |	  13MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |	      |			 |
+	 * |  M3 Dump |  0x4D100000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |	      |			 |
+	 * |   QDSS   |  0x4D200000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |	      |			 |
+	 * |  Caldb   |  0x4D300000  |	   2MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|	      |			 |
+	 * |   data   |  0x4D500000  |	  13MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|	      |			 |
+	 * |  M3 Dump |  0x4E200000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|	      |			 |
+	 * |   QDSS   |  0x4E300000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|	      |			 |
+	 * |  Caldb   |  0x4E400000  |	   5MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|	      |			 |
+	 * |   data   |  0x4E900000  |	  13MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|	      |			 |
+	 * |  M3 Dump |  0x4F600000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|	      |			 |
+	 * |   QDSS   |  0x4F700000  |	   1MB	   |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|	      |			 |
+	 * |  Caldb   |  0x4F800000  |	   5MB	   |
+	 * +----------+--------------+-------------------------+
+	 * |						   |
+	 * |	    Rest of the memory for Linux	   |
+	 * |						   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x4D00000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 01400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xD00000>;
+		};
+
+		m3_dump: m3_dump@4D100000 {
+			no-map;
+			reg = <0x0 0x4D100000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_caldb_region: q6_caldb_region@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0x200000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D500000 {
+			no-map;
+			reg = <0x0 0x4D500000 0x0 0xD00000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E200000 {
+			no-map;
+			reg = <0x0 0x4E200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E300000 {
+			no-map;
+			reg = <0x0 0x4E300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_1: q6_qcn6122_caldb_1@4E400000 {
+			no-map;
+			reg = <0x0 0x4E400000 0x0 0x500000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E900000 {
+			no-map;
+			reg = <0x0 0x4E900000 0x0 0xD00000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4F600000 {
+			no-map;
+			reg = <0x0 0x4F600000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F700000 {
+			no-map;
+			reg = <0x0 0x4F700000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_2: q6_qcn6122_caldb_2@4F800000 {
+			no-map;
+			reg = <0x0 0x4F800000 0x0 0x500000>;
+		};
+
+	#endif
+	};
+
+	soc {
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+
+			ethernet-phy@0 {
+				reg = <28>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x1>;
+			ess-switch@0x39c00000 {
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+						mdiobus = <&mdio0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <0x1c>;
+						mdiobus = <&mdio1>;
+						port_mac_sel = "QGMAC_PORT";
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <28>;
+			mdio-bus = <&mdio1>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+	};
+
+	qcom,test@0 {
+		status = "ok";
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio23", "gpio25", "gpio24", "gpio26";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+			pins = "gpio9";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		qspi_cs {
+			pins = "gpio8";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		qspi_data {
+			pins = "gpio4", "gpio5", "gpio6", "gpio7";
+			function = "qspi_data";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	led_pins: led_pinmux {
+		mux_1 {
+			pins = "gpio38";
+			function = "gpio";
+			bias-pull-down;
+		};
+	};
+	
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		wps_button {
+			pins = "gpio14";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	audio_pins: audio_pinmux {
+		mux_1 {
+			pins = "gpio24";
+			function = "audio_rxbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_2 {
+			pins = "gpio25";
+			function = "audio_rxfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_3 {
+			pins = "gpio26";
+			function = "audio_rxd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_4 {
+			pins = "gpio27";
+			function = "audio_txmclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_5 {
+			pins = "gpio28";
+			function = "audio_txbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_6 {
+			pins = "gpio29";
+			function = "audio_txfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_7 {
+			pins = "gpio30";
+			function = "audio_txd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+};
+
+&soc {
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		led_power: led@38 {
+			label = "blue:status";
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+	};
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 14 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&q6v5_wcss {
+	compatible = "qcom,ipq5018-q6-mpd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	firmware = "IPQ5018/q6_fw.mdt";
+	reg = <0x0cd00000 0x4040>,
+		<0x1938000 0x8>,
+		<0x193d204 0x4>;
+	reg-names = "qdsp6",
+			"tcsr-msip",
+			"tcsr-q6";
+	resets = <&gcc GCC_WCSSAON_RESET>,
+			<&gcc GCC_WCSS_Q6_BCR>;
+
+	reset-names = "wcss_aon_reset",
+			"wcss_q6_reset";
+
+	clocks = <&gcc GCC_Q6_AXIS_CLK>,
+		<&gcc GCC_WCSS_ECAHB_CLK>,
+		<&gcc GCC_Q6_AXIM_CLK>,
+		<&gcc GCC_Q6_AXIM2_CLK>,
+		<&gcc GCC_Q6_AHB_CLK>,
+		<&gcc GCC_Q6_AHB_S_CLK>,
+		<&gcc GCC_WCSS_AXI_S_CLK>;
+	clock-names = "gcc_q6_axis_clk",
+		"gcc_wcss_ecahb_clk",
+		"gcc_q6_axim_clk",
+		"gcc_q6_axim2_clk",
+		"gcc_q6_ahb_clk",
+		"gcc_q6_ahb_s_clk",
+		"gcc_wcss_axi_s_clk";
+
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+
+	qcom,rproc = <&q6v5_wcss>;
+	qcom,bootargs_smem = <507>;
+	boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>,
+			<0x2 0x4 0x2 0x12 0x0 0x0>;
+	status = "ok";
+	q6_wcss_pd1: remoteproc_pd1@4ab000 {
+		compatible = "qcom,ipq5018-wcss-ahb-mpd";
+		reg = <0x4ab000 0x20>;
+		reg-names = "rmb";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+					<&wcss_smp2p_in 9 0>,
+					<&wcss_smp2p_in 12 0>,
+					<&wcss_smp2p_in 11 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		resets = <&gcc GCC_WCSSAON_RESET>,
+				<&gcc GCC_WCSS_BCR>,
+				<&gcc GCC_CE_BCR>;
+		reset-names = "wcss_aon_reset",
+				"wcss_reset",
+				"ce_reset";
+
+		clocks = <&gcc GCC_WCSS_AHB_S_CLK>,
+				<&gcc GCC_WCSS_ACMT_CLK>,
+				<&gcc GCC_WCSS_AXI_M_CLK>;
+		clock-names = "gcc_wcss_ahb_s_clk",
+					"gcc_wcss_acmt_clk",
+					"gcc_wcss_axi_m_clk";
+
+		qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
+
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+					<&wcss_smp2p_out 9>,
+					<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>;
+	#else
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>, <&q6_caldb_region>;
+	#endif
+
+	};
+
+	q6_wcss_pd2: remoteproc_pd2 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "qcn6122/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 16 0>,
+					<&wcss_smp2p_in 17 0>,
+					<&wcss_smp2p_in 20 0>,
+					<&wcss_smp2p_in 19 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 16>,
+					<&wcss_smp2p_out 17>,
+					<&wcss_smp2p_out 18>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>;
+	#else
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>, <&q6_qcn6122_caldb_1>;
+	#endif
+
+	};
+
+	q6_wcss_pd3: remoteproc_pd3 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 24 0>,
+					<&wcss_smp2p_in 25 0>,
+					<&wcss_smp2p_in 28 0>,
+					<&wcss_smp2p_in 27 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 24>,
+					<&wcss_smp2p_out 25>,
+					<&wcss_smp2p_out 26>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef	__IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>;
+	#else
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>, <&q6_qcn6122_caldb_2>;
+	#endif
+	};
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x23>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4D300000 0x4D300000 0 0 0>;
+	qcom,caldb-size = <0x200000>;
+	mem-region = <&q6_ipq5018_data>;
+#else
+	memory-region = <&q6_ipq5018_data>;
+#endif
+	status = "ok";
+};
+
+&wifi1 {
+	/* QCN6122 5G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
+	qcom,rproc = <&q6_wcss_pd2>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x60>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4D500000 0x4D500000 0x4D300000 0x0 0x0>;
+	qcom,caldb-addr = <0x4E400000 0x4E400000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data1>;
+#else
+	memory-region = <&q6_qcn6122_data1>;
+#endif
+	status = "disabled";
+};
+
+&wifi2 {
+	/* QCN6122 6G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
+	qcom,rproc = <&q6_wcss_pd3>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0xb0>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4E900000 0x4E900000 0x4E200000 0x0 0x0>;
+	qcom,caldb-addr = <0x4F800000 0x4F800000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data2>;
+#else
+	memory-region = <&q6_qcn6122_data2>;
+#endif
+	status = "disabled";
+};
+
+&usb3 {
+       status = "ok";
+       device-power-gpio = <&tlmm 24 1>;
+};
+
+&dwc_0 {
+       /delete-property/ #phy-cells;
+       /delete-property/ phys;
+       /delete-property/ phy-names;
+};
+
+&hs_m31phy_0 {
+       status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	perst-gpio = <&tlmm 18 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x2 {
+	perst-gpio = <&tlmm 15 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x1_rp {
+	status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+	status = "disabled";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+
+	};
+};

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-yuncore-fap655.dts

@@ -30,7 +30,7 @@
 		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
 		serial0 = &blsp1_uart1;
 		serial1 = &blsp1_uart2;
-		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp1";
 
 		led-boot = &led_power;
 		led-failsafe = &led_power;
@@ -823,7 +823,7 @@
 #else
 	memory-region = <&q6_qcn6122_data1>;
 #endif
-	status = "disabled";
+	status = "ok";
 };
 
 &wifi2 {

feeds/ipq807x_v5.4/ipq50xx/image/ipq50xx.mk

@@ -72,6 +72,15 @@ define Device/edgecore_oap101e_6e
 endef
 TARGET_DEVICES += edgecore_oap101e_6e
 
+define Device/hfcl_ion4x_w
+  DEVICE_TITLE := HFCL ION4x_w
+  DEVICE_DTS := qcom-ipq5018-hfcl-ion4x_w
+  SUPPORTED_DEVICES := hfcl,ion4x_w
+  DEVICE_PACKAGES := ath11k-wifi-hfcl-ion4x_w ath11k-firmware-ipq50xx-map-spruce
+  DEVICE_DTS_CONFIG := config@mp03.3
+endef
+TARGET_DEVICES += hfcl_ion4x_w
+
 define Device/hfcl_ion4xi_w
   DEVICE_TITLE := HFCL ION4xi_w
   DEVICE_DTS := qcom-ipq5018-hfcl-ion4xi_w

feeds/ipq807x_v5.4/ipq50xx/patches/107-bridge-allow-bcast-mcast-same-port-hairpinmode.patch

@@ -0,0 +1,14 @@
+Index: linux-5.4.164-qsdk-26349818b464f8c7b52d59ce73579d9f3dd6bd5d/net/bridge/br_forward.c
+===================================================================
+--- linux-5.4.164-qsdk-26349818b464f8c7b52d59ce73579d9f3dd6bd5d.orig/net/bridge/br_forward.c
++++ linux-5.4.164-qsdk-26349818b464f8c7b52d59ce73579d9f3dd6bd5d/net/bridge/br_forward.c
+@@ -24,8 +24,7 @@ static inline int should_deliver(const s
+ 	struct net_bridge_vlan_group *vg;
+ 
+ 	vg = nbp_vlan_group_rcu(p);
+-	return (((p->flags & BR_HAIRPIN_MODE) && !is_multicast_ether_addr(eth_hdr(skb)->h_dest))
+-		|| (skb->dev != p->dev)) &&
++	return (((p->flags & BR_HAIRPIN_MODE)) || (skb->dev != p->dev)) &&
+ 		br_allowed_egress(vg, skb) && (p->state == BR_STATE_FORWARDING) &&
+ 		nbp_switchdev_allowed_egress(p, skb) &&
+ 		!br_skb_isolated(p, skb);

feeds/ipq807x_v5.4/ipq60xx/patches/107-bridge-allow-bcast-mcast-same-port-hairpinmode.patch

@@ -0,0 +1,14 @@
+Index: linux-5.4.164-qsdk-26349818b464f8c7b52d59ce73579d9f3dd6bd5d/net/bridge/br_forward.c
+===================================================================
+--- linux-5.4.164-qsdk-26349818b464f8c7b52d59ce73579d9f3dd6bd5d.orig/net/bridge/br_forward.c
++++ linux-5.4.164-qsdk-26349818b464f8c7b52d59ce73579d9f3dd6bd5d/net/bridge/br_forward.c
+@@ -24,8 +24,7 @@ static inline int should_deliver(const s
+ 	struct net_bridge_vlan_group *vg;
+ 
+ 	vg = nbp_vlan_group_rcu(p);
+-	return (((p->flags & BR_HAIRPIN_MODE) && !is_multicast_ether_addr(eth_hdr(skb)->h_dest))
+-		|| (skb->dev != p->dev)) &&
++	return (((p->flags & BR_HAIRPIN_MODE)) || (skb->dev != p->dev)) &&
+ 		br_allowed_egress(vg, skb) && (p->state == BR_STATE_FORWARDING) &&
+ 		nbp_switchdev_allowed_egress(p, skb) &&
+ 		!br_skb_isolated(p, skb);

feeds/ipq807x_v5.4/ipq807x/patches/107-bridge-allow-bcast-mcast-same-port-hairpinmode.patch

@@ -0,0 +1,14 @@
+Index: linux-5.4.164-qsdk-26349818b464f8c7b52d59ce73579d9f3dd6bd5d/net/bridge/br_forward.c
+===================================================================
+--- linux-5.4.164-qsdk-26349818b464f8c7b52d59ce73579d9f3dd6bd5d.orig/net/bridge/br_forward.c
++++ linux-5.4.164-qsdk-26349818b464f8c7b52d59ce73579d9f3dd6bd5d/net/bridge/br_forward.c
+@@ -24,8 +24,7 @@ static inline int should_deliver(const s
+ 	struct net_bridge_vlan_group *vg;
+ 
+ 	vg = nbp_vlan_group_rcu(p);
+-	return (((p->flags & BR_HAIRPIN_MODE) && !is_multicast_ether_addr(eth_hdr(skb)->h_dest))
+-		|| (skb->dev != p->dev)) &&
++	return (((p->flags & BR_HAIRPIN_MODE)) || (skb->dev != p->dev)) &&
+ 		br_allowed_egress(vg, skb) && (p->state == BR_STATE_FORWARDING) &&
+ 		nbp_switchdev_allowed_egress(p, skb) &&
+ 		!br_skb_isolated(p, skb);

feeds/ucentral/ucentral-client/Makefile

@@ -4,10 +4,10 @@ PKG_NAME:=ucentral-client
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-client.git
-PKG_MIRROR_HASH:=bf8d2c105e8e7f91b7a3d44917a4024307a5ddf9fbafcd00c9830ec8a96ec1f7
+PKG_MIRROR_HASH:=279c58711c354372d570320651644bf75ce758c6197a7eb8dda481a925c82620
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_DATE:=2022-06-22
-PKG_SOURCE_VERSION:=3025bf919e30cf201fe9a84feeaaf580b752fa95
+PKG_SOURCE_VERSION:=6ca7b2e43c20a92508bf408e586c310dfff38f51
 
 PKG_LICENSE:=BSD-3-Clause
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>

feeds/ucentral/ucentral-event/files/ucentral-event

@@ -78,7 +78,8 @@ function event(object, verb, payload) {
 		});
 }
 
-let handlers = {
+let handlers;
+handlers = {
 	'sta-authorized': function(notify, hapd) {
 		/* force FDB flush on QCA Wifi-6 silicon */
 		system(`echo ${notify.data.address} > /sys/kernel/debug/ssdk_flush_mac`);
@@ -87,7 +88,7 @@ let handlers = {
 			ssid: hapd.ssid,
 			bssid: hapd.bssid,
 		});
-		if (ratelimit && !wildcard(notify.data.ifname, 'wlanc*')) {
+		if (ratelimit) {
 			let msg = {
 				device: hapd.ifname,
 				address: notify.data.address,
@@ -102,7 +103,7 @@ let handlers = {
 	},
 
 	disassoc: function(notify, hapd) {
-		if (ratelimit && !wildcard(notify.data.ifname, 'wlanc*')) {
+		if (ratelimit) {
 			let msg = {
 				address: notify.data.address,
 			};
@@ -118,7 +119,30 @@ let handlers = {
 		});
 	}, 
 
+	vlan_add_swconfig: function(notify) {
+		let msg = {                             
+			name: notify.data.ifname,   
+			'link-ext': true,           
+			vlan: [ `${notify.data.vlan_id}:u` ]  
+		};                                          
+		ubus.call('network.interface.up_none', 'add_device', msg);          
+
+		msg = {                          
+			name: 'eth0.' + notify.data.vlan_id,
+			vlan: [ `${notify.data.vlan_id}:u` ]
+		};
+
+		ubus.call('network.interface.up_none', 'add_device', msg);
+
+		let cmd = 'swconfig dev ' + config.config.swconfig + ' vlan ' + notify.data.vlan_id + ' set ports \"' + join(' ', config.config.swconfig_ports) + '\"';
+		system(cmd);                                                                                                                                           
+		system('swconfig dev ' + config.config.swconfig + ' set apply');    
+	},
+
 	vlan_add: function(notify) {
+		if (config.config.swconfig)
+			return handlers.vlan_add_swconfig(notify);
+
 		for (let wan in wan_ports) {
 			let msg = {
 				name: wan,

feeds/ucentral/ucentral-schema/Makefile

@@ -4,10 +4,10 @@ PKG_NAME:=ucentral-schema
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-schema.git
-PKG_MIRROR_HASH:=8b8dfea69e4547a4169f4b095742b86d675988b03204577bcbb308619763579b
+PKG_MIRROR_HASH:=8558ddc1b975a9b0bf1832c3277a99de95e9cf3682a671991d3125c04d375e96
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_DATE:=2022-05-29
-PKG_SOURCE_VERSION:=f8608f6b21236a383b0c284d3b23d5710cbeccc4
+PKG_SOURCE_VERSION:=e77cd3fa1ea727cbdfc64f78aff2401a869edc27
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

feeds/ucentral/ucentral-schema/files/etc/ucentral/examples/multi-psk.json

@@ -34,27 +34,6 @@
 			],
 			"ipv4": {
 				"addressing": "dynamic"
-			}
-		},
-		{
-			"name": "LAN",
-			"role": "downstream",
-			"services": [ "http", "ssh" ],
-			"ethernet": [
-				{
-					"select-ports": [
-						"LAN*"
-					]
-				}
-			],
-			"ipv4": {
-				"addressing": "static",
-				"subnet": "192.168.1.1/24",
-				"dhcp": {
-					"lease-first": 10,
-					"lease-count": 100,
-					"lease-time": "6h"
-				}
 			},
 			"ssids": [
 				{
@@ -84,6 +63,27 @@
 					}
 				}
 			]
+		},
+		{
+			"name": "LAN",
+			"role": "downstream",
+			"services": [ "http", "ssh" ],
+			"ethernet": [
+				{
+					"select-ports": [
+						"LAN*"
+					]
+				}
+			],
+			"ipv4": {
+				"addressing": "static",
+				"subnet": "192.168.1.1/24",
+				"dhcp": {
+					"lease-first": 10,
+					"lease-count": 100,
+					"lease-time": "6h"
+				}
+			}
 		}
 	],
 	"services": {

feeds/ucentral/ucentral-schema/files/etc/ucentral/ucentral.cfg.0000000001

@@ -73,7 +73,7 @@
 		"admin-ui": {
 			"wifi-ssid": "Maverick",
 			"wifi-bands": [ "5G" ],
-			"offline-trigger": 300,
+			"offline-trigger": 300
 		}
 	}
 }

feeds/ucentral/ucentral-state/files/ucentral-state

@@ -18,6 +18,7 @@ let ubus = libubus.connect();
 let uci = libuci.cursor();
 let config;
 let offline_timer;
+let current_state;
 
 function self_healing() {
 
@@ -67,15 +68,19 @@ state = {
 };
 
 function offline_handler() {
-	//ulog(LOG_INFO, 'going offline\n');
+	let status = ubus.call('ucentral', 'status');
+	if (status?.connected)
+		return;
+	ulog(LOG_INFO, 'going offline\n');
 	ubus.call('network.interface.admin_ui', 'up');
 }
 
 function online_handler() {
 	ulog(LOG_INFO, 'going online\n');
 	ubus.call('network.interface.admin_ui', 'down');
-	if (offline_timer)
+	if (offline_timer) {
 		offline_timer.cancel();
+	}
 }
 
 function config_load() {
@@ -140,8 +145,12 @@ let state_handler = {
 		if (!led)
 			return ubus.STATUS_INVALID_ARGUMENT;
 		led_write(led, 'trigger', 'heartbeat');
-		if (config.ui.offline_trigger)
-			offline_timer = uloop.timer(config.ui.offline_trigger * 1000, offline_handler);
+		if (config.ui.offline_trigger) {
+			if (offline_timer)
+				offline_timer.set(config.ui.offline_trigger * 1000);
+			else
+				offline_timer = uloop.timer(config.ui.offline_trigger * 1000, offline_handler);
+		}
 		return 0;
 	},
 
@@ -175,8 +184,12 @@ let state_handler = {
 let ubus_methods = {
 	set: {
 		call: function(req) {
+			ulog(LOG_INFO, 'state %s -> %s\n', current_state, req.args.state);
+			if (current_state == req.args.state)
+				return;
 			if (!state_handler[req.args.state])
 				return ubus.STATUS_INVALID_ARGUMENT;
+			current_state = req.args.state;
 			blink_timeout();
 			ulog(LOG_INFO, 'set state -> ' + req.args.state + '\n');
 			

feeds/ucentral/uspot/files/usr/share/uspot/uspot.uc

@@ -460,8 +460,10 @@ function run_service() {
 
 				address = uc(address);
 
-				if (interfaces[interface].clients[address])
+				if (interfaces[interface].clients[address]) {
+					radius_terminate(interface, address, radtc_logout);
 					client_remove(interface, address, 'client_remove event');
+				}
 
 				return 0;
 			},

feeds/ucentral/uspot/src/radius.c

@@ -181,7 +181,7 @@ static int cb_chap_passwd(void *p, size_t s, struct blob_attr *b)
 	int len;
 
 	assert(s >= 17);
-	len = str_to_hex(blobmsg_get_string(b), str+1, 16);
+	len = str_to_hex(blobmsg_get_string(b), str+1, 17);
 
 	return len+1;
 }
@@ -192,7 +192,7 @@ static int cb_chap_challenge(void *p, size_t s, struct blob_attr *b)
 	int len;
 
 	assert(s >= 16);
-	len = str_to_hex(blobmsg_get_string(b), str, 16);
+	len = str_to_hex(blobmsg_get_string(b), str, 17);
 
 	return len;
 }

feeds/wifi-ax/ath11k-wifi/Makefile

@@ -128,6 +128,16 @@ $(call Package/ath11k-wifi-default)
     TITLE:=motorola q14 bdf
 endef
 
+define Package/ath11k-wifi-optimcloud-d50
+$(call Package/ath11k-wifi-default)
+    TITLE:=optimcloud d50 bdf
+endef
+
+define Package/ath11k-wifi-optimcloud-d60
+$(call Package/ath11k-wifi-default)
+    TITLE:=optimcloud d60 bdf
+endef
+
 define Package/ath11k-wifi-plasmacloud-pax1800
 $(call Package/ath11k-wifi-default)
     TITLE:=plasmacloud-pax1800(-v2) bdf
@@ -274,6 +284,20 @@ define Package/ath11k-wifi-cig-wf196_6g-us/install
 	echo -n 'US' > $(1)/lib/firmware/country
 endef
 
+define Package/ath11k-wifi-optimcloud-d50/install
+	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/
+	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/QCN9074/hw1.0/
+	$(INSTALL_DATA) ./board-optimcloud-d50.bin.IPQ5018 $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/board.bin
+	$(INSTALL_DATA) ./board-optimcloud-d50.bin.QCN9074 $(1)/lib/firmware/ath11k/QCN9074/hw1.0/board.bin
+endef
+
+define Package/ath11k-wifi-optimcloud-d60/install
+	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/
+	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/QCN9074/hw1.0/
+	$(INSTALL_DATA) ./board-optimcloud-d60.bin.QCN9074 $(1)/lib/firmware/ath11k/QCN9074/hw1.0/board.bin
+	$(INSTALL_DATA) ./board-optimcloud-d60.bin.QCN9074 $(1)/lib/firmware/ath11k/QCN9074/hw1.0/board.bin
+endef
+
 define Package/ath11k-wifi-gl-ax1800/install
 	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/IPQ6018/hw1.0/
 	$(INSTALL_DATA) ./board-gl-ax1800.bin.IPQ6018 $(1)/lib/firmware/ath11k/IPQ6018/hw1.0/board-2.bin
@@ -388,6 +412,8 @@ $(eval $(call BuildPackage,ath11k-wifi-cig-wf188n-us))
 $(eval $(call BuildPackage,ath11k-wifi-cig-wf196_6g-ca))
 $(eval $(call BuildPackage,ath11k-wifi-cig-wf196_6g-us))
 $(eval $(call BuildPackage,ath11k-wifi-motorola-q14))
+$(eval $(call BuildPackage,ath11k-wifi-optimcloud-d50))
+$(eval $(call BuildPackage,ath11k-wifi-optimcloud-d60))
 $(eval $(call BuildPackage,ath11k-wifi-hfcl-ion4xi))
 $(eval $(call BuildPackage,ath11k-wifi-hfcl-ion4xi_wp))
 $(eval $(call BuildPackage,ath11k-wifi-hfcl-ion4xi_w))

feeds/wifi-ax/hostapd/files/hostapd.sh

@@ -745,11 +745,11 @@ hostapd_set_bss_options() {
 	}
 
 	case "$auth_type" in
-		sae|owe|eap192|eap256)
+		sae|owe|eap192|eap2)
 			set_default ieee80211w 2
 			set_default sae_require_mfp 1
 		;;
-		psk-sae|psk2-radius|eap-eap256)
+		psk-sae|psk2-radius|eap-eap2)
 			set_default ieee80211w 1
 			set_default sae_require_mfp 1
 		;;
@@ -796,7 +796,7 @@ hostapd_set_bss_options() {
 			vlan_possible=1
 			wps_possible=1
 		;;
-		eap|eap192|eap-eap256|eap256)
+		eap|eap192|eap-eap2|eap2)
 			append_radius_server
 			# radius can provide VLAN ID for clients
 			vlan_possible=1
@@ -1342,10 +1342,10 @@ wpa_supplicant_add_network() {
 		default_disabled
 
 	case "$auth_type" in
-		sae|owe|eap-eap256)
+		sae|owe|eap-eap2)
 			set_default ieee80211w 2
 		;;
-		psk-sae|eap192|eap256)
+		psk-sae|eap192|eap2)
 			set_default ieee80211w 1
 		;;
 	esac
@@ -1423,7 +1423,7 @@ wpa_supplicant_add_network() {
 			fi
 			append network_data "$passphrase" "$N$T"
 		;;
-		eap|eap192|eap-eap256|eap256)
+		eap|eap192|eap-eap2|eap2)
 			hostapd_append_wpa_key_mgmt
 			key_mgmt="$wpa_key_mgmt"
 

patches/0069-hostapd-sync-builtin-patches.patch

@@ -1,11 +1,11 @@
-From b09c1180c1ba4a30b70530b90748e7682931b91a Mon Sep 17 00:00:00 2001
+From b9abe28ab24fbf333960078a9e2255d01cbf408b Mon Sep 17 00:00:00 2001
 From: John Crispin <john@phrozen.org>
 Date: Mon, 20 Nov 2023 08:33:42 +0100
 Subject: [PATCH] hostapd: sync builtin patches
 
 Signed-off-by: John Crispin <john@phrozen.org>
 ---
- .../network/services/hostapd/files/hostapd.sh |   5 +-
+ .../network/services/hostapd/files/hostapd.sh |  17 +-
  .../hostapd/patches/760-acs_exclude_dfs.patch |   8 +-
  .../hostapd/patches/780-maxassoc.patch        |   6 +-
  .../patches/790-wired-dynamic-vlan.patch      |  33 +++
@@ -16,7 +16,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
  .../hostapd/patches/999-ssi_signal.patch      |  81 +++++++
  .../services/hostapd/src/src/ap/ubus.c        | 229 ++++++++++++++++--
  .../services/hostapd/src/src/ap/ubus.h        |   1 +
- 11 files changed, 491 insertions(+), 55 deletions(-)
+ 11 files changed, 497 insertions(+), 61 deletions(-)
  create mode 100644 package/network/services/hostapd/patches/790-wired-dynamic-vlan.patch
  create mode 100644 package/network/services/hostapd/patches/900-coa.patch
  create mode 100644 package/network/services/hostapd/patches/901-coa-ubus.patch
@@ -24,7 +24,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
  create mode 100644 package/network/services/hostapd/patches/999-ssi_signal.patch
 
 diff --git a/package/network/services/hostapd/files/hostapd.sh b/package/network/services/hostapd/files/hostapd.sh
-index 145848189d..19d5138510 100644
+index 145848189d..958d5a9ac6 100644
 --- a/package/network/services/hostapd/files/hostapd.sh
 +++ b/package/network/services/hostapd/files/hostapd.sh
 @@ -48,15 +48,14 @@ hostapd_append_wpa_key_mgmt() {
@@ -45,6 +45,51 @@ index 145848189d..19d5138510 100644
  			append wpa_key_mgmt "WPA-EAP-SHA256"
  			[ "${ieee80211r:-0}" -gt 0 ] && append wpa_key_mgmt "FT-EAP"
  		;;
+@@ -746,11 +745,11 @@ hostapd_set_bss_options() {
+ 	}
+ 
+ 	case "$auth_type" in
+-		sae|owe|eap192|eap256)
++		sae|owe|eap192|eap2)
+ 			set_default ieee80211w 2
+ 			set_default sae_require_mfp 1
+ 		;;
+-		psk-sae|psk2-radius|eap-eap256)
++		psk-sae|psk2-radius|eap-eap2)
+ 			set_default ieee80211w 1
+ 			set_default sae_require_mfp 1
+ 		;;
+@@ -798,7 +797,7 @@ hostapd_set_bss_options() {
+ 			vlan_possible=1
+ 			wps_possible=1
+ 		;;
+-		eap|eap192|eap-eap256|eap256)
++		eap|eap192|eap-eap2|eap2)
+ 			append_radius_server
+ 			# radius can provide VLAN ID for clients
+ 			vlan_possible=1
+@@ -1344,10 +1343,10 @@ wpa_supplicant_add_network() {
+ 		default_disabled
+ 
+ 	case "$auth_type" in
+-		sae|owe|eap-eap256)
++		sae|owe|eap-eap2)
+ 			set_default ieee80211w 2
+ 		;;
+-		psk-sae|eap192|eap256)
++		psk-sae|eap192|eap2)
+ 			set_default ieee80211w 1
+ 		;;
+ 	esac
+@@ -1425,7 +1424,7 @@ wpa_supplicant_add_network() {
+ 			fi
+ 			append network_data "$passphrase" "$N$T"
+ 		;;
+-		eap|eap192|eap-eap256|eap256)
++		eap|eap192|eap-eap2|eap2)
+ 			hostapd_append_wpa_key_mgmt
+ 			key_mgmt="$wpa_key_mgmt"
+ 
 diff --git a/package/network/services/hostapd/patches/760-acs_exclude_dfs.patch b/package/network/services/hostapd/patches/760-acs_exclude_dfs.patch
 index 52d63c5ff9..27b3a6161a 100644
 --- a/package/network/services/hostapd/patches/760-acs_exclude_dfs.patch

patches/0072-netifd-fix-vlan-awareness-bug.patch

@@ -0,0 +1,103 @@
+From 782cefa73e24512dd675b51aa969103bdccee773 Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Tue, 5 Dec 2023 15:57:08 +0100
+Subject: [PATCH] netifd: fix vlan-awareness bug
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ .../netifd/patches/004-vlan-awareness.patch   | 83 +++++++++++++++++++
+ 1 file changed, 83 insertions(+)
+ create mode 100644 package/network/config/netifd/patches/004-vlan-awareness.patch
+
+diff --git a/package/network/config/netifd/patches/004-vlan-awareness.patch b/package/network/config/netifd/patches/004-vlan-awareness.patch
+new file mode 100644
+index 0000000000..00d43957e1
+--- /dev/null
++++ b/package/network/config/netifd/patches/004-vlan-awareness.patch
+@@ -0,0 +1,83 @@
++diff --git a/bridge.c b/bridge.c
++index c931923e3299..2128ec75a0fb 100644
++--- a/bridge.c
+++++ b/bridge.c
++@@ -223,7 +223,9 @@ bridge_set_member_vlan(struct bridge_member *bm, struct bridge_vlan *vlan, bool
++ 	if (!port)
++ 		return;
++ 
++-	if (bridge_member_vlan_is_pvid(bm, port))
+++	if (!add && bm->pvid == vlan->vid)
+++		bm->pvid = 0;
+++	else if (add && bridge_member_vlan_is_pvid(bm, port))
++ 		bm->pvid = vlan->vid;
++ 
++ 	__bridge_set_member_vlan(bm, vlan, port, add);
++@@ -275,12 +277,12 @@ bridge_set_vlan_state(struct bridge_state *bst, struct bridge_vlan *vlan, bool a
++ {
++ 	struct bridge_member *bm;
++ 	struct bridge_vlan *vlan2;
+++	bool clear_pvid = false;
++ 
++ 	bridge_set_local_vlan(bst, vlan, add);
++ 
++ 	vlist_for_each_element(&bst->members, bm, node) {
++ 		struct bridge_vlan_port *port;
++-		int new_pvid = -1;
++ 
++ 		port = bridge_find_vlan_member_port(bm, vlan);
++ 		if (!port)
++@@ -293,17 +295,18 @@ bridge_set_vlan_state(struct bridge_state *bst, struct bridge_vlan *vlan, bool a
++ 			vlan2 = bridge_recalc_member_pvid(bm);
++ 			if (vlan2 && vlan2->vid != vlan->vid) {
++ 				bridge_set_member_vlan(bm, vlan2, false);
+++				bm->pvid = vlan2->vid;
++ 				bridge_set_member_vlan(bm, vlan2, true);
+++			} else if (!vlan2) {
+++				clear_pvid = true;
++ 			}
++-			new_pvid = vlan2 ? vlan2->vid : 0;
++ 		}
++ 
++-		if (!bm->present)
++-			continue;
+++		if (bm->present)
+++			__bridge_set_member_vlan(bm, vlan, port, add);
++ 
++-		__bridge_set_member_vlan(bm, vlan, port, add);
++-		if (new_pvid >= 0)
++-			bm->pvid = new_pvid;
+++		if (clear_pvid)
+++			bm->pvid = 0;
++ 	}
++ }
++ 
++@@ -1369,14 +1372,14 @@ bridge_vlan_update(struct vlist_tree *tree, struct vlist_node *node_new,
++ 	struct bridge_state *bst = container_of(tree, struct bridge_state, dev.vlans);
++ 	struct bridge_vlan *vlan_new = NULL, *vlan_old = NULL;
++ 
++-	if (!bst->has_vlans || !bst->active)
++-		goto out;
++-
++ 	if (node_old)
++ 		vlan_old = container_of(node_old, struct bridge_vlan, node);
++ 	if (node_new)
++ 		vlan_new = container_of(node_new, struct bridge_vlan, node);
++ 
+++	if (!bst->has_vlans || !bst->active)
+++		goto out;
+++
++ 	if (node_new && node_old && bridge_vlan_equal(vlan_old, vlan_new)) {
++ 		list_splice_init(&vlan_old->hotplug_ports, &vlan_new->hotplug_ports);
++ 		goto out;
++@@ -1391,9 +1394,8 @@ bridge_vlan_update(struct vlist_tree *tree, struct vlist_node *node_new,
++ 	if (node_new)
++ 		vlan_new->pending = true;
++ 
++-	bst->dev.config_pending = true;
++-
++ out:
+++	bst->dev.config_pending = true;
++ 	bridge_vlan_free(vlan_old);
++ }
++ 
+-- 
+2.34.1
+

profiles/cig_wf186h.yml

@@ -3,7 +3,7 @@ profile: cig_wf186h
 target: ipq50xx
 subtarget: generic
 description: Build image for the Cigtech Wall Plate WF186h
-image: bin/targets/ipq50xx/generic.openwrt-ipq50xx-cig_wf186h-squashfs-sysupgrade.tar
+image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-cig_wf186h-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
     path: ../../feeds/ipq807x_v5.4

profiles/cig_wf196.yml

@@ -1,9 +1,9 @@
 ---
-profile: cig_wf196_ca
+profile: cig_wf196_us
 target: ipq807x
 subtarget: generic
-description: Build image for the CIG WF196 (CA)
-image: bin/targets/ipq807x/generic/openwrt-ipq807x-cig_wf196_ca-squashfs-sysupgrade.tar
+description: Build image for the CIG WF196 (US)
+image: bin/targets/ipq807x/generic/openwrt-ipq807x-cig_wf196_us-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
     path: ../../feeds/ipq807x_v5.4

profiles/hfcl_ion4x.yml

@@ -1,14 +1,13 @@
 ---
 profile: hfcl_ion4x
-target: ipq807x
-subtarget: ipq60xx
+target: ipq60xx
+subtarget: generic
 description: Build image for the HFCL ION 4X
-image: bin/targets/ipq807x/ipq60xx/openwrt-ipq807x-hfcl_ion4x-squashfs-sysupgrade.tar
+image: bin/targets/ipq60xx/generic/openwrt-ipq60xx-hfcl_ion4x-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x
+    path: ../../feeds/ipq807x_v5.4
 packages:
-  - ipq807x
+  - ipq60xx
 include:
-  - wifi-ax
   - ucentral-ap

profiles/hfcl_ion4x_2.yml

@@ -1,14 +1,13 @@
 ---
 profile: hfcl_ion4x_2
-target: ipq807x
-subtarget: ipq60xx
+target: ipq60xx
+subtarget: generic
 description: Build image for the HFCL ION 4X_2
-image: bin/targets/ipq807x/ipq60xx/openwrt-ipq807x-hfcl_ion4x_2-squashfs-sysupgrade.tar
+image: bin/targets/ipq60xx/generic/openwrt-ipq60xx-hfcl_ion4x_2-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x
+    path: ../../feeds/ipq807x_v5.4
 packages:
-  - ipq807x
+  - ipq60xx
 include:
-  - wifi-ax
   - ucentral-ap

profiles/hfcl_ion4x_w.yml

@@ -1,15 +1,14 @@
 profile: hfcl_ion4x_w
-target: ipq807x
-subtarget: ipq50xx
+target: ipq50xx
+subtarget: generic
 description: Build image for the HFCL ion4x_w
-image: bin/targets/ipq807x/ipq50xx/openwrt-ipq807x-hfcl_ion4x_w-squashfs-sysupgrade.tar
+image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-hfcl_ion4x_w-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x
+    path: ../../feeds/ipq807x_v5.4
 include:
-  - wifi-ax
   - ucentral-ap
 packages:
-  - ipq807x
+  - ipq50xx
 diffconfig: |
   CONFIG_KERNEL_IPQ_MEM_PROFILE=512

profiles/hfcl_ion4xe.yml

@@ -1,14 +1,13 @@
 ---
 profile: hfcl_ion4xe
-target: ipq807x
-subtarget: ipq60xx
+target: ipq60xx
+subtarget: generic
 description: Build image for the HFCL ION 4XE
-image: bin/targets/ipq807x/ipq60xx/openwrt-ipq807x-hfcl_ion4xe-squashfs-sysupgrade.tar
+image: bin/targets/ipq60xx/generic/openwrt-ipq60xx-hfcl_ion4xe-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x
+    path: ../../feeds/ipq807x_v5.4
 packages:
-  - ipq807x
+  - ipq60xx
 include:
-  - wifi-ax
   - ucentral-ap

profiles/hfcl_ion4xi.yml

@@ -1,14 +1,13 @@
 ---
 profile: hfcl_ion4xi
-target: ipq807x
-subtarget: ipq60xx
+target: ipq60xx
+subtarget: generic
 description: Build image for the HFCL ION 4XI
-image: bin/targets/ipq807x/ipq60xx/openwrt-ipq807x-hfcl_ion4xi-squashfs-sysupgrade.tar
+image: bin/targets/ipq60xx/generic/openwrt-ipq60xx-hfcl_ion4xi-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x
+    path: ../../feeds/ipq807x_v5.4
 packages:
-  - ipq807x
+  - ipq60xx
 include:
-  - wifi-ax
   - ucentral-ap

profiles/hfcl_ion4xi_w.yml

@@ -1,15 +1,14 @@
 profile: hfcl_ion4xi_w
-target: ipq807x
-subtarget: ipq50xx
+target: ipq50xx
+subtarget: generic
 description: Build image for the HFCL ion4xi_w
-image: bin/targets/ipq807x/ipq50xx/openwrt-ipq807x-hfcl_ion4xi_w-squashfs-sysupgrade.tar
+image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-hfcl_ion4xi_w-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x
+    path: ../../feeds/ipq807x_v5.4
 include:
-  - wifi-ax
   - ucentral-ap
 packages:
-  - ipq807x
+  - ipq50xx
 diffconfig: |
   CONFIG_KERNEL_IPQ_MEM_PROFILE=512

profiles/indio_um-305ac.yml

@@ -6,4 +6,3 @@ description: Build image for the Indio 305AC
 image: bin/targets/ath79/generic/openwrt-ath79-generic-indio_um-305ac-squashfs-sysupgrade.bin
 include:
   - ucentral-ap
-  - wifi-ath10k

profiles/optimcloud_d50-5g.yml

@@ -1,15 +1,20 @@
 profile: optimcloud_d50-5g
-target: ipq50xx
-subtarget: generic
+target: ipq807x
+subtarget: ipq50xx
 description: Build image for the OptimCloud D50-5G
-image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-optimcloud_d50-5g-squashfs-sysupgrade.tar
+image: bin/targets/ipq807x/ipq50xx/openwrt-ipq807x-optimcloud_d50-5g-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x_v5.4
+    path: ../../feeds/ipq807x
 include:
-  - wifi-ax-v54
+  - wifi-ax
   - ucentral-ap
+  - turris
+  - safe-search
+  - parental
+  - cyber
+  - oqs
 packages:
-  - ipq50xx
+  - ipq807x
 diffconfig: |
   CONFIG_KERNEL_IPQ_MEM_PROFILE=512

profiles/optimcloud_d50.yml

@@ -1,15 +1,20 @@
 profile: optimcloud_d50
-target: ipq50xx
-subtarget: generic
+target: ipq807x
+subtarget: ipq50xx
 description: Build image for the OptimCloud D50
-image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-optimcloud-d50-squashfs-sysupgrade.tar
+image: bin/targets/ipq807x/ipq50xx/openwrt-ipq807x-optimcloud_d50-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x_v5.4
+    path: ../../feeds/ipq807x
 include:
-  - wifi-ax-v54
+  - wifi-ax
   - ucentral-ap
+  - turris
+  - safe-search
+  - parental
+  - cyber
+  - oqs
 packages:
-  - ipq50xx
+  - ipq807x
 diffconfig: |
   CONFIG_KERNEL_IPQ_MEM_PROFILE=512

profiles/optimcloud_d60-5g.yml

@@ -1,15 +1,20 @@
 profile: optimcloud_d60-5g
-target: ipq50xx
-subtarget: generic
+target: ipq807x
+subtarget: ipq50xx
 description: Build image for the OptimCloud D60-5G
-image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-optimcloud_d60-5g-squashfs-sysupgrade.tar
+image: bin/targets/ipq807x/ipq50xx/openwrt-ipq807x-optimcloud_d60-5g-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x_v5.4
+    path: ../../feeds/ipq807x
 include:
-  - wifi-ax-v54
+  - wifi-ax
   - ucentral-ap
+  - turris
+  - safe-search
+  - parental
+  - cyber
+  - oqs
 packages:
-  - ipq50xx
+  - ipq807x
 diffconfig: |
   CONFIG_KERNEL_IPQ_MEM_PROFILE=512

profiles/optimcloud_d60.yml

@@ -1,15 +1,20 @@
 profile: optimcloud_d60
-target: ipq50xx
-subtarget: generic
+target: ipq807x
+subtarget: ipq50xx
 description: Build image for the OptimCloud D60
-image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-optimcloud-d60-squashfs-sysupgrade.tar
+image: bin/targets/ipq807x/ipq50xx/openwrt-ipq807x-optimcloud_d60-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x_v5.4
+    path: ../../feeds/ipq807x
 include:
-  - wifi-ax-v54
+  - wifi-ax
   - ucentral-ap
+  - turris
+  - safe-search
+  - parental
+  - cyber
+  - oqs
 packages:
-  - ipq50xx
+  - ipq807x
 diffconfig: |
   CONFIG_KERNEL_IPQ_MEM_PROFILE=512

profiles/yuncore_fap655-ath12.yml

@@ -0,0 +1,15 @@
+---
+profile: yuncore_fap655
+target: ipq50xx
+subtarget: generic
+description: Build image for Yuncore FAP655
+image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-yuncore_fap655-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x_v5.4
+include:
+  - ucentral-ap
+packages:
+  - ipq50xx
+diffconfig: |
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=512

profiles/yuncore_fap655-legacy.yml

@@ -1,14 +0,0 @@
----
-profile: yuncore_fap655
-target: ipq807x
-subtarget: ipq50xx
-description: Build image for Yuncore FAP655
-image: bin/targets/ipq807x/ipq50xx/openwrt-ipq807x-yuncore_fap655-squashfs-sysupgrade.tar
-feeds:
-  - name: ipq807x
-    path: ../../feeds/ipq807x
-include:
-  - wifi-ax
-  - ucentral-ap
-packages:
-  - ipq807x

profiles/yuncore_fap655.yml

@@ -1,15 +1,14 @@
 ---
 profile: yuncore_fap655
-target: ipq50xx
-subtarget: generic
+target: ipq807x
+subtarget: ipq50xx
 description: Build image for Yuncore FAP655
-image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-yuncore_fap655-squashfs-sysupgrade.tar
+image: bin/targets/ipq807x/ipq50xx/openwrt-ipq807x-yuncore_fap655-squashfs-sysupgrade.tar
 feeds:
   - name: ipq807x
-    path: ../../feeds/ipq807x_v5.4
+    path: ../../feeds/ipq807x
 include:
+  - wifi-ax
   - ucentral-ap
 packages:
-  - ipq50xx
-diffconfig: |
-  CONFIG_KERNEL_IPQ_MEM_PROFILE=512
+  - ipq807x