Merge pull request #734 from Telecominfraproject/main

ipq807x: add new files & made change for udaya outdoor wifi-6

feeds/ipq807x_v5.4/ath11k-wifi/Makefile

@@ -57,6 +57,7 @@ ALLWIFIBOARDS:= \
 	yuncore-fap650 \
 	yuncore-fap655 \
 	udaya-a6-id2 \
+	udaya-a6-od2 \
 	meshpp-s618
 
 ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ath11k-wifi-$(BOARD))
@@ -413,6 +414,7 @@ $(eval $(call generate-ath11k-wifi-package,muxi-ap3220l,MUXI AP3220L))
 $(eval $(call generate-ath11k-wifi-package,yuncore-fap650,YunCore FAP650))
 $(eval $(call generate-ath11k-wifi-package,yuncore-fap655,YunCore FAP655))
 $(eval $(call generate-ath11k-wifi-package,udaya-a6-id2,Udaya A6-ID2))
+$(eval $(call generate-ath11k-wifi-package,udaya-a6-od2,Udaya A6-OD2))
 $(eval $(call generate-ath11k-wifi-package,wallys-dr5018,Wallys DR5018))
 
 $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/board.d/02_network

@@ -31,6 +31,10 @@ qcom_setup_interfaces()
 		ucidef_set_interface_wan "eth1"
 		ucidef_set_interface_lan "eth0"
 		;;
+	udaya,a6-od2)
+		ucidef_set_interface_wan "eth1"
+		ucidef_set_interface_lan "eth0"
+		;;
 	edgecore,oap101|\
  	edgecore,oap101-6e|\
 	edgecore,oap101e|\

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -135,6 +135,7 @@ ath11k/IPQ5018/hw1.0/caldata.bin)
 	optimcloud,d50|\
 	optimcloud,d50-5g|\
 	udaya,a6-id2|\
+	udaya,a6-od2|\
 	wallys,dr5018|\
 	yuncore,fap655|\
 	glinet,b3000)
@@ -155,6 +156,7 @@ ath11k/qcn6122/hw1.0/caldata_1.bin)
 	edgecore,oap101e|\
 	edgecore,oap101e-6e|\
 	udaya,a6-id2|\
+	udaya,a6-od2|\
 	hfcl,ion4xi_w|\
 	wallys,dr5018|\
 	yuncore,fap655)

feeds/ipq807x_v5.4/ipq50xx/base-files/lib/upgrade/platform.sh

@@ -85,6 +85,7 @@ platform_check_image() {
 	yuncore,fap655|\
 	glinet,b3000|\
 	udaya,a6-id2|\
+	udaya,a6-od2|\
 	edgecore,oap101|\
 	edgecore,oap101-6e|\
 	edgecore,oap101e|\
@@ -128,6 +129,7 @@ platform_do_upgrade() {
 	cig,wf186w|\
 	cig,wf186h|\
 	udaya,a6-id2|\
+	udaya,a6-od2|\
 	wallys,dr5018|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-udaya-a6-od2.dts

@@ -0,0 +1,900 @@
+/dts-v1/;
+/* Copyright (c) 2018-2021, The Linux Foundation. All rights reserved.
+ *
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "ipq5018.dtsi"
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "Udaya A6-OD2";
+	compatible = "udaya,a6-od2", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*                   256 MB Profile
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |           8MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x40800000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D100000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D300000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E000000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E100000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4E200000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4EF00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4F000000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x4100000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x1400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xD00000>;
+		};
+
+		m3_dump: m3_dump@4D100000 {
+			no-map;
+			reg = <0x0 0x4D100000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0xD00000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E000000 {
+			no-map;
+			reg = <0x0 0x4E000000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E100000 {
+			no-map;
+			reg = <0x0 0x4E100000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E200000 {
+			no-map;
+			reg = <0x0 0x4E200000 0x0 0xD00000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4EF00000 {
+			no-map;
+			reg = <0x0 0x4EF00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F000000 {
+			no-map;
+			reg = <0x0 0x4F000000 0x0 0x100000>;
+		};
+	#else
+	/*                 512MB/1GB Profiles
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x41000000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D100000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  Caldb   |  0x4D300000  |           2MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D500000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  Caldb   |  0x4E400000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4E900000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4F600000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4F700000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  Caldb   |  0x4F800000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x4D00000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 01400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xD00000>;
+		};
+
+		m3_dump: m3_dump@4D100000 {
+			no-map;
+			reg = <0x0 0x4D100000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_caldb_region: q6_caldb_region@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0x200000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D500000 {
+			no-map;
+			reg = <0x0 0x4D500000 0x0 0xD00000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E200000 {
+			no-map;
+			reg = <0x0 0x4E200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E300000 {
+			no-map;
+			reg = <0x0 0x4E300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_1: q6_qcn6122_caldb_1@4E400000 {
+			no-map;
+			reg = <0x0 0x4E400000 0x0 0x500000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E900000 {
+			no-map;
+			reg = <0x0 0x4E900000 0x0 0xD00000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4F600000 {
+			no-map;
+			reg = <0x0 0x4F600000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F700000 {
+			no-map;
+			reg = <0x0 0x4F700000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_2: q6_qcn6122_caldb_2@4F800000 {
+			no-map;
+			reg = <0x0 0x4F800000 0x0 0x500000>;
+		};
+
+	#endif
+	};
+
+	soc {
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+
+			ethernet-phy@0 {
+				reg = <28>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x1>;
+			ess-switch@0x39c00000 {
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+						mdiobus = <&mdio0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <0x1c>;
+						mdiobus = <&mdio1>;
+						port_mac_sel = "QGMAC_PORT";
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+			qcom,rx-page-mode = <0>;
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <28>;
+			mdio-bus = <&mdio1>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+			qcom,rx-page-mode = <0>;
+		};
+
+		nss-macsec1 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <0x1c>;
+			mdiobus = <&mdio1>;
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&button_pins>;
+			pinctrl-names = "default";
+
+			reset {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		leds {
+			compatible = "gpio-leds";
+			pinctrl-0 = <&leds_pins>;
+			pinctrl-names = "default";
+
+			led_power: led@30 {
+				label = "green:power";
+				gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>;
+				default-state = "on";
+			};
+		};
+	};
+
+	qcom,test@0 {
+		status = "ok";
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio23", "gpio25", "gpio24", "gpio26";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+			pins = "gpio9";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		qspi_cs {
+			pins = "gpio8";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		qspi_data {
+			pins = "gpio4", "gpio5", "gpio6", "gpio7";
+			function = "qspi_data";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	leds_pins: leds_pins {
+		led_status {
+			pins = "gpio30";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	audio_pins: audio_pinmux {
+		mux_1 {
+			pins = "gpio24";
+			function = "audio_rxbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_2 {
+			pins = "gpio25";
+			function = "audio_rxfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_3 {
+			pins = "gpio26";
+			function = "audio_rxd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_4 {
+			pins = "gpio27";
+			function = "audio_txmclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_5 {
+			pins = "gpio28";
+			function = "audio_txbclk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_6 {
+			pins = "gpio29";
+			function = "audio_txfsync";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		mux_7 {
+			pins = "gpio30";
+			function = "audio_txd";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+};
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&q6v5_wcss {
+	compatible = "qcom,ipq5018-q6-mpd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	firmware = "IPQ5018/q6_fw.mdt";
+	reg = <0x0cd00000 0x4040>,
+		<0x1938000 0x8>,
+		<0x193d204 0x4>;
+	reg-names = "qdsp6",
+			"tcsr-msip",
+			"tcsr-q6";
+	resets = <&gcc GCC_WCSSAON_RESET>,
+			<&gcc GCC_WCSS_Q6_BCR>;
+
+	reset-names = "wcss_aon_reset",
+			"wcss_q6_reset";
+
+	clocks = <&gcc GCC_Q6_AXIS_CLK>,
+		<&gcc GCC_WCSS_ECAHB_CLK>,
+		<&gcc GCC_Q6_AXIM_CLK>,
+		<&gcc GCC_Q6_AXIM2_CLK>,
+		<&gcc GCC_Q6_AHB_CLK>,
+		<&gcc GCC_Q6_AHB_S_CLK>,
+		<&gcc GCC_WCSS_AXI_S_CLK>;
+	clock-names = "gcc_q6_axis_clk",
+		"gcc_wcss_ecahb_clk",
+		"gcc_q6_axim_clk",
+		"gcc_q6_axim2_clk",
+		"gcc_q6_ahb_clk",
+		"gcc_q6_ahb_s_clk",
+		"gcc_wcss_axi_s_clk";
+
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+
+	qcom,rproc = <&q6v5_wcss>;
+	qcom,bootargs_smem = <507>;
+	boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>,
+			<0x2 0x4 0x2 0x12 0x0 0x0>;
+	status = "ok";
+	q6_wcss_pd1: remoteproc_pd1@4ab000 {
+		compatible = "qcom,ipq5018-wcss-ahb-mpd";
+		reg = <0x4ab000 0x20>;
+		reg-names = "rmb";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+					<&wcss_smp2p_in 9 0>,
+					<&wcss_smp2p_in 12 0>,
+					<&wcss_smp2p_in 11 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		resets = <&gcc GCC_WCSSAON_RESET>,
+				<&gcc GCC_WCSS_BCR>,
+				<&gcc GCC_CE_BCR>;
+		reset-names = "wcss_aon_reset",
+				"wcss_reset",
+				"ce_reset";
+
+		clocks = <&gcc GCC_WCSS_AHB_S_CLK>,
+				<&gcc GCC_WCSS_ACMT_CLK>,
+				<&gcc GCC_WCSS_AXI_M_CLK>;
+		clock-names = "gcc_wcss_ahb_s_clk",
+					"gcc_wcss_acmt_clk",
+					"gcc_wcss_axi_m_clk";
+
+		qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
+
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+					<&wcss_smp2p_out 9>,
+					<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>;
+	#else
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>, <&q6_caldb_region>;
+	#endif
+
+	};
+
+	q6_wcss_pd2: remoteproc_pd2 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "qcn6122/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 16 0>,
+					<&wcss_smp2p_in 17 0>,
+					<&wcss_smp2p_in 20 0>,
+					<&wcss_smp2p_in 19 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 16>,
+					<&wcss_smp2p_out 17>,
+					<&wcss_smp2p_out 18>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>;
+	#else
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>, <&q6_qcn6122_caldb_1>;
+	#endif
+
+	};
+
+	q6_wcss_pd3: remoteproc_pd3 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 24 0>,
+					<&wcss_smp2p_in 25 0>,
+					<&wcss_smp2p_in 28 0>,
+					<&wcss_smp2p_in 27 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 24>,
+					<&wcss_smp2p_out 25>,
+					<&wcss_smp2p_out 26>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef	__IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>;
+	#else
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>, <&q6_qcn6122_caldb_2>;
+	#endif
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x23>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4D300000 0x4D300000 0 0 0>;
+	qcom,caldb-size = <0x200000>;
+	mem-region = <&q6_ipq5018_data>;
+#else
+	memory-region = <&q6_ipq5018_data>;
+#endif
+	status = "ok";
+};
+
+&wifi1 {
+	/* QCN6122 5G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
+	qcom,rproc = <&q6_wcss_pd2>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x60>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4D500000 0x4D500000 0x4D300000 0x0 0x0>;
+	qcom,caldb-addr = <0x4E400000 0x4E400000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data1>;
+#else
+	memory-region = <&q6_qcn6122_data1>;
+#endif
+	status = "ok";
+};
+
+&wifi2 {
+	/* QCN6122 6G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
+	qcom,rproc = <&q6_wcss_pd3>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0xb0>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4E900000 0x4E900000 0x4E200000 0x0 0x0>;
+	qcom,caldb-addr = <0x4F800000 0x4F800000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data2>;
+#else
+	memory-region = <&q6_qcn6122_data2>;
+#endif
+	status = "disabled";
+};
+
+&usb3 {
+       status = "ok";
+       device-power-gpio = <&tlmm 24 1>;
+};
+
+&dwc_0 {
+       /delete-property/ #phy-cells;
+       /delete-property/ phys;
+       /delete-property/ phy-names;
+};
+
+&hs_m31phy_0 {
+       status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	perst-gpio = <&tlmm 18 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x2 {
+	perst-gpio = <&tlmm 15 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x1_rp {
+	status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+	status = "disabled";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+
+	};
+};

feeds/ipq807x_v5.4/ipq50xx/image/ipq50xx.mk

@@ -80,6 +80,15 @@ define Device/udaya_a6_id2
 endef
 TARGET_DEVICES += udaya_a6_id2
 
+define Device/udaya_a6_od2
+  DEVICE_TITLE := Udaya A6 - OD2
+  DEVICE_DTS := qcom-ipq5018-udaya-a6-od2
+  SUPPORTED_DEVICES := udaya,a6-od2
+  DEVICE_PACKAGES := ath11k-wifi-udaya-a6-od2 ath11k-firmware-ipq50xx-spruce ath11k-firmware-qcn6122
+  DEVICE_DTS_CONFIG := config@mp03.5-c1
+endef
+TARGET_DEVICES += udaya_a6_od2
+
 define Device/wallys_dr5018
   DEVICE_TITLE := Wallys DR5018
   DEVICE_DTS := qcom-ipq5018-wallys-dr5018

feeds/ipq95xx/wireguard/Makefile

@@ -15,7 +15,7 @@ PKG_VERSION:=1.0.20211208
 PKG_RELEASE:=1
 
 PKG_SOURCE:=wireguard-linux-compat-$(PKG_VERSION).tar.xz
-PKG_SOURCE_URL:=https://git.zx2c4.com/wireguard-linux-compat/snapshot/
+PKG_SOURCE_URL:=https://ucentral.io/
 PKG_HASH:=c0e607138a17daac656f508d8e63ea3737b5221fa5d9288191ddeb099f5a3b92
 
 PKG_LICENSE:=GPL-2.0

feeds/ucentral/ucentral-schema/Makefile

@@ -4,10 +4,10 @@ PKG_NAME:=ucentral-schema
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-schema.git
-PKG_MIRROR_HASH:=802ef1c815e96f7151866c2fd2ef6c83a370e6c1159fb52f7261613dcdc449cc
+PKG_MIRROR_HASH:=ed369fd1083e37af03a9d85a9a03316f2f6ad94aaa605f5b5818fbf91a717ea8
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_DATE:=2024-07-03
-PKG_SOURCE_VERSION:=baeef766f40d6970105c20ec6767e8e09644c622
+PKG_SOURCE_VERSION:=a0f26ac8817d83dfb1b362af390e4216318096f0
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

profiles/udaya_a6-od2.yml

@@ -0,0 +1,15 @@
+---
+profile: udaya_a6_od2
+target: ipq50xx
+subtarget: generic
+description: Build image for the Udaya A6 - od2
+image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-udaya_a6_od2-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x_v5.4
+include:
+  - ucentral-ap
+packages:
+  - ipq50xx
+diffconfig: |
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=512