Occasionally the charge circuit on samus gets wedged and will not
charge. This change detects when the charge circuit has failed
and automatically recovers from it. It uses the BQ PROCHOT warning
to detect the failure by setting PROCHOT to trigger when the BQ
thinks input current is higher than the input current limit. When
the failure is detected, the EC disables charging and tells PD MCU
to disable CHARGE_EN, then a couple seconds later, it re-enables
charging.
This CL also adds more communication between EC and PD for the EC
to be able to set the charge state for the PD. Valid charge states
are: No charging allowed, 5V charging only, and max charging. The
EC uses this as such:
- When the EC gets AC present interrupt, it sets off a deferred
function to change charge state to max charging after some delay
to give time for the charge circuit to settle down.
- When the EC gets AC disconnect interrupt, it disables charging
briefly, enables learn mode, and then sets 5V charging allowed.
This allows for the same starting conditions in the charge circuit
for every AC attach.
- When the EC detects a wedged charge circuit, it disables charging
and waits a few seconds before re-enabling 5V only charging.
Additionally, this change moves the charging cutoff in S3/S5/G3 when
the battery is full to the EC. With the added control for the EC
to set the PD charging state, it is more convenient for the EC to
manage cutting off charging when battery is full.
BUG=chrome-os-partner:36081
BRANCH=samus
TEST=test the basics:
- connect/disconnect zinger a bunch of times
- connect and disconnect two zingers in different order
- connect two zingers and charge override between the two
test the automatic charge wedge recover:
- wedge the charge circuit by setting charger voltage under battery
voltage: "charger voltage 7000"
- wait a few seconds for the system to recover and check it is charging
with "battery" command
test full battery charge cutoff:
- added console command to change battery soc in board/samus/extpower.c:
static int cmd_battfake(int argc, char **argv)
{
char *e;
battery_soc = strtoi(argv[1], &e, 10);
batt_soc_change();
return EC_SUCCESS;
}
DECLARE_CONSOLE_COMMAND(battfake, cmd_battfake, "", "", NULL);
- in S0, tested "battfake 100" does not disable charging.
- in G3, tested "battfake 100" disables charging and "battfake 99"
re-enables charging.
- set "battfake 100" and tested transitioning to S0 enables charging and
transitioning to S5 disables charging.
- attached two chargers and used charge override to select active port.
then toggled "battfake 100" to "battfake 99" back and forth and verified
charge override port is still the same.
test third-party 12V charger:
- plug in a bunch of times and make sure we stay at 5V for 500ms and then
transition to 12V
test with no battery:
- tested five different units with no battery and just zinger. 3/5 boot,
while the other 2 don't. But, the 2 that don't boot without battery also
can't boot w/o battery when this CL is reverted, so I don't think this
change is causing the problem, I think there is an electrical limitation.
test with EVT zinger:
- EVT zingers (P2 - C2) negotiate very quickly after connection, which
can cause INA problems w/o this CL. Tested an EVT zinger with samus and
did a bunch of connections and disconnections and verified that we always
wait at 5V for 500ms and that we don't wedge the INA circuit on connect.
test backwards compatibility:
- test new PD with old EC and make sure we can charge with zinger.
(note that if the charge circuit wedges, we won't be able to unwedge it).
- test old PD with new EC and make sure we can charge with zinger.
Change-Id: I7703b7a2ab1209d7f559b265b03517e79c74b16a
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/245253
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
More updates to connection state machine. Adds CONFIG option
for backwards compatible DFP (used on zinger), and change UFP
state machine to debounce CC while VBUS is not present.
BUG=chrome-os-partner:33680
BRANCH=samus
TEST=load on samus and zinger and connect a bunch of times. also
test samus to samus connection.
Change-Id: Ia967eb6a17b10aa0c05a30686235fbf8a24e9a7b
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/240587
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Certain platforms may wish to have a longer shutdown timeout, so make
the timeout a config option.
BUG=chrome-os-partner:35188
TEST=Manual on Samus with subsequent CL. Set config option to increase
timeout, verify that timeout is extended.
BRANCH=Samus
Change-Id: I69feb0d31fdc53e533671dec1e88ba96cc4553c2
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/240815
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Add a FIFO to log important events on the PD MCU and coming from the PD
accessories.
The retrieval of the accessories log from the accessories by the PD MCU
is not implemented yet.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:32785
TEST=execute "ectool --name=cros_pd pdlog"
before and after plugging Zinger charger.
Change-Id: If96d73e711ff6ad64cfb99bd3e4d2d8f2643f19a
Reviewed-on: https://chromium-review.googlesource.com/238854
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Assuming the dut has red/green battery led and a single power led
CONFIG_LED_POLICY_STD implements the chromeos spec:
* power led on in S0
* power led off in S5
* power led pulsing in S3
* battery led amber when charging
* battery led green when fully charged with AC
* battery led off when discharging
* battery led pulsing red when battery error
BUG=chrome-os-partner:35355
TEST=The Charging led behavior should match the cros spec
BRANCH=None
Change-Id: I645a939ecc2d44d73d2f52b295f9c7e8c923f77b
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/240705
Reviewed-by: Randall Spangler <rspangler@chromium.org>
BUG=chrome-os-partner:35312
BRANCH=none
TEST=make buildall -j
I added a debug message to nrf51/hwtimer.c to show when the timer overflowed.
"forcetime 4 0xfffff000" overflows to 5.00000000 in 4096 microseconds.
Define CONFIG_CMD_FORCETIME to enable it.
Change-Id: I30835d038ef8cd639565ffb7a638979d95d0a684
Signed-off-by: Myles Watson <mylesgw@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/239968
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Fix potential junk at end of PD TX transmit by adding to the DMA
transmit complete interrupt a blocking wait for SPI to finish and
then immediately disable SPI clock. This means we block in an
interrupt function for approximately 45us at the end of every
transmit. But, this is the highest priority thing going on anyway.
Note, there is still a potential for junk if both ports are
transmitting at the same time and finish very close to the same time.
BUG=chrome-os-partner:34600
BRANCH=samus
TEST=load onto samus and test communications with zinger. tested
specifically with an old zinger CL,
https://chromium-review.googlesource.com/#/c/226118/11,
which watchdogs when samus has junk at end of transmit. Tested
without this CL and verified we could never successfully flash zinger
over PD due to this watchdog and verified on scope presence of junk.
Then tested with this change and was able to successfully flash
zinger using ectool on both ports in both polarities.
Change-Id: If0cd9ab0551d36a7d7dc10232b6476dd56735972
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/239244
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
These USB type-C accessories don't have a write-protect GPIO.
Add a configure flag (CONFIG_WP_ALWAYS) to force the flash
write-protection on the dongles.
Also set the read protection (by elevating RDP to level 1),
so trying to unprotect the flash will trigger a full erase.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:35088
TEST=boot Hoho,
check the flash OBR and WRPR registers:
"rw 0x4002201c" / "rw 0x40022020"
and the option bytes write-protect bits: "rw 0x1FFFF808"
dump the logical state with "flashinfo" command.
> rw 0x4002201c
read 0x40022020 = 0xffff0002
> rw 0x40022020
read 0x40022020 = 0xffff0000
> rw 0x1FFFF808
read 0x1ffff808 = 0xff00ff00
> flashinfo
Physical: 128 KB
Usable: 128 KB
Write: 2 B (ideal 2 B)
Erase: 2048 B (to 1-bits)
Protect: 4096 B
Flags: wp_gpio_asserted ro_at_boot ro_now
Protected now:
YYYYYYYY YYYYYYYY ........ ........
Change-Id: I45bbc0bce40ecc174b6b8a1ebacf4f53d2fd372d
Reviewed-on: https://chromium-review.googlesource.com/238893
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
Create optional config to remove 'typec' command for flash savings.
While its a useful command to many developers its not used in any
factory flows and costs ~500bytes of flash space.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:34489
TEST=manual, compiles and command still there. If #undef saves ~500bytes.
Change-Id: I02c0ec1dd503b02f86d8ac3d5e99ed6ad493c95c
Reviewed-on: https://chromium-review.googlesource.com/238462
Tested-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
Create optional config to remove 'hash' console command and undef it
for a few space-constrained boards (ryu*, samus_pd).
Signed-off-by: Todd Broch <tbroch@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:34489
TEST=manual,
- compile for ryu, samus_pd and save ~400bytes
- 'hash' command no longer appears as a console command
Change-Id: I054fd4473911dd362c2c1d171ee7aaad859d893a
Reviewed-on: https://chromium-review.googlesource.com/238433
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
Add config option, CONFIG_CMD_PD_FLASH, and undef by default. This subcmd in
the 'pd' command is large (500 bytes) and can be performed from host via
ectool.
Additionally the python script, util/flash_pd.py, is likely outdated or needs
adjustments for various timing related nuances.
Note, as flash command contained subcmd 'version' have added that under
'pd <port> vdm vers' to keep that functionality by default.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:34489
TEST=manual,
run 'pd 1 flash signature' get 'parameter 1 invalid'
run 'pd 1 vdm vers' w/ zinger in port 1 see version string returned.
Change-Id: If282933c1d29febb43b5cf476a121be6b5a1071b
Reviewed-on: https://chromium-review.googlesource.com/238291
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
Add a rate limiter to host commands so that a host that is continuously
sending host commands doesn't watchdog the EC.
BUG=chrome-os-partner:33905
BRANCH=samus
TEST=loaded onto samus and tested remote update of zinger 10 times.
also tested EC + PD software sync.
Change-Id: Ia024179c46b2180ee97ea1902de343306142311c
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/235530
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
In order to reduce flash size on some constrained boards this CL
modifies the GPIO macro in gpio_list.h to change the name field from
that listed 'name' to the concat of 'port' and 'pin'.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:34489
TEST=manual
1. build with and without CONFIG_COMMON_GPIO_SHORTNAMES
See 897 bytes savings with config option
2. See reduced names for gpioget
> gpioget
0 E6
0 F2
1 B0
Change-Id: Ife1e1e2bcfa620ba87fe6c1ce2b47fe258c46514
Reviewed-on: https://chromium-review.googlesource.com/234587
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
Ryu sensor hub has asymectric RO/RW images. The first one is very limited
(not i2c master, no sensor drivers, gesture recognition).
Image size is alter to offer more space for the RW firmware image,
compiled with ryu_sh board.
To write RO image and basic RW image:
flashrom -V -p ec:type=sh,block=0x800 --fast-verify -w /tmp/ryu_sh_loader/ec.bin
To write the expected RW image:
flashrom -V -p ec:type=sh,block=0x800 --fast-verify -w -i EC_RW:/tmp/ryu_sh/ec.bin
BRANCH=ToT
BUG=chrome-os-partner:33908
CQ-DEPEND=CL:231970,CL:233233
TEST=load on Ryu, confirmed limited operation.
Change-Id: Ib976e2b048935adfb9b2b072c071db5be2bc1c09
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/231984
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
dingdong/hoho have no capability to measure VBUS which is advantageous
in determining what timeouts to honor. Previously we simply assumed
vbus was on and that made things happy until,
e0c80ac pd: on hard reset go to a hard reset recovery state
which introduced proper handling around sink & source reset recovery.
With VBUS assumed 'on' this leads to short timeouts chosen
(PD_T_SAFE_0V) which in turn causes sink to resend hard resets before
source has had time (PD_T_SRC_RECOVER) to handle request.
This change creates config CONFIG_USB_PD_NO_VBUS_DETECT for devices
without the capability to account for lack of VBUS detect.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:34090
TEST=manual
from samus_pd 'pd 1 flash reboot' is successful
Change-Id: I9ef9b0115c7be6c56c64556d2ce8c296f95c614e
Reviewed-on: https://chromium-review.googlesource.com/233024
Tested-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
For accessories without software-sync mechanism, add the option to do a
RSA-based signature verification of the Read-Write firmware.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:31192
TEST=enable the configuration on Fruitpie and see the RW firmware
validated and jump to. Tried with good and bad RW images.
Change-Id: I3c886c2cbe17ca9543e19bf8599061c3f9751d4f
Reviewed-on: https://chromium-review.googlesource.com/229594
Reviewed-by: Todd Broch <tbroch@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
Remove host_event_commands.c from build to save flash space. The
PD MCU does not use host event infrastructure and instead has a
simple gpio line it uses to notify EC that it has info to share.
BUG=none
BRANCH=samus
TEST=make buildall. view the .map file and see we save about 700
bytes of flash.
Change-Id: I71b8a4e32b9ecb57eb1a57f6d28652476ee6afe6
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/231444
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add commands to send PD packets and to tweak individual parameters (TX
clock frequency, RX detection threshold, resistors on CCx).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:28337
TEST=verify that the PD sniffing is still working by dumping traffic
between Zinger and Samus.
Connect Twinkie to Zinger, set Rd by using "tw res NONE RD" and see VBUS
going to 5V (reading it using "ina 0").
Send a BIST mode 2 request using the following command :
tw send 2 0x1043 50000000
and see the other end starting sending BIST.
Change-Id: I3c8ddf858435ac1c17a43f59351bbaa69603a209
Reviewed-on: https://chromium-review.googlesource.com/227778
Reviewed-by: Todd Broch <tbroch@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
With this change we can use power event to configure sensors
and trigger motion detection in suspend.
BUG=chrome-os-partner:31071
BRANCH=ToT
TEST=Check power states. Check power up messages and commands are
present at the console.
Message at boot:
[0.007142 hash start 0x00010000 0x000096dd]
[0.007293 Inits done]
[0.007506 power state 2 = S3, in 0x0000]
[0.007765 power state 3 = S0, in 0x0000]
[0.007908 event set 0x00002000]
[0.008021 hostcmd init 0x2000]
[0.146870 hash done
f87d7824b439db923d270df016af5aabec51b73505b7c4faa6e40c16b12dd392]
Change-Id: I9c56fe5203506462f0820bbc8a5fe4528f6805ac
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/226881
Reviewed-by: Sheng-liang Song <ssl@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Allow policy layer to request a PR or DR swap upon formation of
a power contract. Zinger always asks for a data swap so it can
be a UFP, and Samus asks for a data swap only if it is a UFP to
become a DFP.
BUG=chrome-os-partner:33754, chrome-os-partner:31195
BRANCH=samus
TEST=load onto samus and zinger and make sure they swap roles
upon connect with no collisions
Change-Id: I275c9669549c26f25c58f80845daad8edab11313
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/229327
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Disable most of the pd console command to save space. The command
can still be used with subcommands "state" and "dump" to get state
information and change debug level.
BUG=none
BRANCH=none
TEST=make buildall with CONFIG_CMD_PD defined and undefined. Also
undefined the config option and loaded onto samus and verified that
the pd 0 state command still works.
Change-Id: Ie41bad53122a1e2a9ef4bad6423b9cdc85f53742
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/229420
Reviewed-by: Vic Yang <victoryang@chromium.org>
This provides a framework for additional work. It
exposes an API (ccd_set_mode) that can be used by the
PD code to enable Case Closed Debug. Enabling CCD will
result in the USB 2.0 lines on Ryu (proto 2) to be
disconnected from the AP and for the USB peripheral to
be enabled and connected to the host. The result is
an enumerated device with no interfaces.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Enable CCD ryu_p2 and verify that it is enumerated
by the host correctly. This requires a reworked
Ryu (proto 2 with pullup).
Change-Id: I1fbecdd5f94a61519cfc18c5e087892c6bd77fde
Reviewed-on: https://chromium-review.googlesource.com/229139
Reviewed-by: Anton Staaf <robotboy@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Previously enabling USB would automatically (using an
init hook) initialize the USB peripheral. This would
take over the GPIO lines assigned to the USB module.
This is not OK on Ryu for Case Closed Debug because it
interferes with the AP's access to the USB 2.0 lines
even when not in Case Close Debug mode.
This change adds a configuration option to inhibit this
default initialization of the USB peripheral. It also
renames the existing CONFIG_USB_INHIBIT to
CONFIG_USB_INHIBIT_CONNECT now that there are two
possible inhibitions.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Enable console on ryu_p2 and discovery-stm32f072 board
Verify that it works on both
Change-Id: I6734357131b4356e3d4164349d6c74deac196ce5
Reviewed-on: https://chromium-review.googlesource.com/229138
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Modules that are enabled are listed below:
- Power Sequencing
- Keyboard Scan and Protocol
- LPC to support Keyboard
- Power Button Task
ec.spi.bin has to be generated manualy using
pack_ec.py
BUG=None
BRANCH=None
TEST=Tested on Stargo-Proto board
Change-Id: Ic5d504c3d6e9c7c5f3482fb7e9e37800b6274824
Signed-off-by: Divya Jyothi <divya.jyothi@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/226303
Reviewed-by: Vic Yang <victoryang@chromium.org>
Per table 6-24 of USB PD spec an alternate mode adapter (AMA) should
include both product & AMA VDOs.
BRANCH=samus
BUG=chrome-os-partner:31192,chrome-os-partner:31193
TEST=manual,
Connect hoho/dingdong to fpie/samus and see product VDO proceed the
AMA VDO in DFP_U console output:
Product VDO -----------------------------v
|------|
SVDM/5 [1] ff008041 340018d1 00000000 50100001 1100000b
Note, hoho's PID == 0x5010
And dingdong (0x5011)
SVDM/5 [1] ff008041 340018d1 00000000 50110001 1100000b
Also see bcdDevice field in descriptor match above data.
$ lsusb -v -d 18d1: | egrep -i "idproduct|bcddev"
idProduct 0x5011
bcdDevice 0.01
Change-Id: I4d898816a45c68c7ff75a54fd348fc11be408ae0
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/226125
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Split motion_sense.c.
Translate the accel data in the Android coordinate right away.
BUG=chrome-os-partner:32002
BRANCH=ToT
TEST=On samus, check lid angle are still correct.
Change-Id: If743e25245dc1ce4cdacb8a4d5af22616c4a79e4
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/225486
Reviewed-by: Sheng-liang Song <ssl@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Move gesture to common directory, 1st step to be reused by
other board.
Cleanup motion_sense shutdown path.
BUG=chrome-os-partner:33102
TEST=Double tap still works on Samus
BRANCH=ToT
Change-Id: I0a3b38c4a7dbe95c27dcdebff04c1176aaf932d1
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/225235
Reviewed-by: Sheng-liang Song <ssl@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
This implements a new API for EC modules to define MKBP event sources
and send MKBP event to the AP. Also, a new host command
EC_CMD_GET_NEXT_EVENT is added for the AP to query the pending MKBP
events. Each event type may have custom event data sent along with the
event.
BRANCH=None
BUG=chrome-os-partner:33194
TEST=Enable MKBP event on Ryu. Set a host event from EC console, run
'ectool nextevent', and see MKBP event 0x01 (HOST_EVENT) and the set
host event.
Signed-off-by: Vic Yang <victoryang@chromium.org>
Change-Id: I28a1b7e826bcc102bbe39016c9bb3e37d125664c
Reviewed-on: https://chromium-review.googlesource.com/224905
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Simple control of SPI for flashing over USB.
This driver is working, and using the discovery board
with a W25Q16 flash chip attached flashrom can read,
erase, write, and verify the whole chip in 45 seconds.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Change-Id: I224f1f87cd6adc8b64c17de1df98dae0a9cfa6a5
Reviewed-on: https://chromium-review.googlesource.com/218740
Reviewed-by: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
This adds the DMA channel definition for UART2 and allows selection of
DMA channel for UART.
BRANCH=None
BUG=chrome-os-partner:32660
TEST=With the CLs to enable the new Ryu boards, check the console is
working.
Change-Id: I964c284899777dda67c264e622aea6aba752ea76
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/224176
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add macro for default hibernate delay, and set to 7 days on samus.
Also, adds CONFIG_ option for hibernating early if low on battery.
For samus, setting early hibernate at 1 day when battery < 10%.
BUG=chrome-os-partner:33088
BRANCH=samus
TEST=make buildall
Added ccprintf("Target shutdown: %.6ld\n", target_time); to print
out target shutdown time after setting it. Verifed the following
on samus
1) If CONFIG_HIBERNATE_DELAY_SEC is left at default 3600 (samus
board.h does not overwrite it), then target time is 3600s.
2) If CONFIG_HIBERNATE_DELAY_SEC is defined in samus/board.h, then
target time equals that value.
3) If CONFIG_HIBERNATE_DELAY_SEC is defined as 1 week and
CONFIG_HIBERNATE_BATT_PCT is defined to 10% and
CONFIG_HIBERNATE_BATT_SEC is 1 day, then when battery is between 8-10%
target time is 1 day and if battery is at 11%, target time is 1 week.
Change-Id: Ief155ad6c327775fa348d3458fc47ee9dd8569c3
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/224520
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The register format of INA231 and INA219 are very much alike. In our
use case, we only need to use different coversion coefficient.
BRANCH=None
BUG=chrome-os-partner:32764
TEST='ina 0' on Plankton V2.
TEST=Build twinkie.
Change-Id: I9c8e21e30ed844566793dcc1221f865400c3d90d
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/223370
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Adds double tap detection for samus. When user double taps
in S3 or lower to show battery state of charge on lightbar.
BUG=chrome-os-partner:29041
BRANCH=samus
TEST=make buildall
Tap the lid in S3 or lower.
Change-Id: Ic5f4709bdee2472cb7e91717318337b04bae1fc8
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/221965
Reviewed-by: David Schneider <dnschneid@chromium.org>
The BOS (Binary Device Object Store) descriptor was added to the USB
specification (3.0) to allow a richer set of device capability
specific descriptors.
The Billboard class is meant to expose (read-only) the status of USB
devices capable of alternate mode functions. It's required to use the
BOS descriptor type and at a high level looks like:
- BOS Device Descriptor (5bytes)
- Container ID Device Capability Descriptor (20bytes)
- Billboard Device Capability Descriptor (44byte + 4 * numSVIDs)
This CL adds:
1. Ability for Get Descriptor on BOS descriptors. Note hidden behind
CONFIG_USB_BOS as these descriptors change USB device requirements
to:
- bcdUSB >= 0201
- no interface descriptors
2. structures for all BOS, Container & Billboard descriptor elements
complete w/ CamelCase.
BRANCH=none
BUG=chrome-os-partner:32652
TEST=compiles with CONFIG_USB & CONFIG_USB_BOS enabled.
Change-Id: I1b24bc728f2ebba7d91840801d2ebe576e240e7c
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/221570
Add support for enabling USB type-C Vconn by defining CONFIG_USBC_VCONN.
Enable Vconn support for samus, ryu, and fruitpie.
BUG=chrome-os-partner:30445
BRANCH=samus
TEST=make buildall
Change-Id: Ibe247286c96fd5a8fa12c88a4e3a5fea02997134
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/222284
Reviewed-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Changed sending of info VDM from the UFP side in SNK_DISCONNECTED
to the DFP side in SRC_READY to match the PD spec. Only the DFP
is supposed to send VDMs, and by default the power source is the
DFP. This affects simple DFPs such as power adapters, they must
initiate the info VDM once a power contract has been negotiated.
BUG=none
BRANCH=samus
TEST=load onto samus_pd and zinger and make sure that when you
attached zinger to samus, samus receives info VDM and prints out
something like:
VDM/7 [11] 18d1000b
Dev:1 SW:2280 RW:0
Change-Id: I16ceac31939fdc1c74be7323e628dd8706e1283b
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/221174
Reviewed-by: Todd Broch <tbroch@chromium.org>
The Zinger RW is now signed with 2048-bit RSA key (using SHA-256 as
digest).
This CL implements the verification mechanism.
note: the RSA key used for signing must be provided as a .pem file.
The path to .pem file must be provided in the PEM environment variable.
By default, it's using the dev key stored in zinger_dev_key.pem.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:28336
TEST=on Zinger, run with properly signed RW firmware and corrupted
firmware and check the serial traces.
Change-Id: Ia58482458904a3ed72d6b0e95996cae86a0ead83
Reviewed-on: https://chromium-review.googlesource.com/220178
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Minimuffin is identical to zinger, same MCU, same gpio, same
circuitry aroundt the MCU with two differences:
- Rated current is 2.25A instead of 3A
- USB PD hardware device ID needs to be different so that host
can differentiate between the two.
Due to the similarity between the two, minimuffin is defined
as a symlink to the zinger board.
BUG=none
BRANCH=samus
TEST=make BOARD=minimuffin
load onto a zinger and verify that samus reads device ID correctly
and limits input current limit to 2.25mA.
Change-Id: Ie39ec43262c7d14663eb68abff073bfeec451a24
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/220689
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Enabled deep sleeping during S0. This was previously inhibited by
SLEEP_MASK_AP_RUN but the new config option (CONFIG_LOW_POWER_S0) will ignore it.
SPI needed a sleep mask, it essentially gets enabled and disabled whenever the
CS changes. Warning: waking up when the CS falls takes a little time, if the AP
sends fast data before the 48MHz clock is enabled characters will get corrupted;
leave about 30uS time for the clock to start.
CQ-DEPEND=CL:219997
CQ-DEPEND=CL:220243
CQ-DEPEND=CL:220461
BUG=chrome-os-partner:32223
BRANCH=none
TEST=load onto pinky, boot the AP(S0), use idlestats command to verify
that we are going into deep sleep (STOP mode). Verify that everything works
normally during S0(SPI, keyboard, anything that requires the EC to wakeup).
Change-Id: I81c4fa472332f1ad8ad93301089a99dcdb108948
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/219555
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Currently, when an assertion fails, the error message is like:
ASSERTION FAILURE '1 + 1 == 3' in command_apreset() at common/chipset.c:24
To save flash space, let's add an option to remove the failed
expression and function name. The error message becomes:
ASSERTION FAILURE at common/chipset.c:24
BUG=chrome-os-partner:32203
TEST=make buildall
TEST=Add an assertion and triggers it. Check error message.
BRANCH=None
Change-Id: Ie323d5b43cbff2cd8f6cd5bb46c1f34ecd16bd5e
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/219670
Reviewed-by: Randall Spangler <rspangler@chromium.org>
2048-bit RSA public key cryptography signature verification code
which uses a pre-processed key for computation.
it is based on the code from vboot :
platform/vboot_reference/firmware/2lib/2rsa.c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:28336
TEST=using following CL, on Zinger, verify RW firmware signature.
Change-Id: I681a29144eb805cd5758aa6efe697ce2f656a298
Reviewed-on: https://chromium-review.googlesource.com/220186
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
