Our previous idea to cut Rd for many reset cases cannot work if cr50
consistently resets the EC by asserting the reset pin shortly after
power-on. Therefore, make a decision based upon whether battery-backed
memory indicates we previously negotiated a PD power contract as a sink.
If we previously did not negotiate a contract, or if power was removed
from the device (causing battery-backed memory to wipe) then we can
assume that we don't have an active power contract.
BUG=chrome-os-partner:62952
BRANCH=reef
TEST=On reef, run "cutoff" on the console, reattach AC, and verify
device successfully wakes. Also verify Rp is dropped on console 'reboot'
and F3 + power from RW.
Change-Id: Ie300b9589cac6be7a69b77678bea6b1b6b25578c
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/443356
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
ROLLBACK region will be used to store rollback information, and
can be protected independently of RW (it can only be protected when
RO is protected, though).
This is only supported on stm32f0 currently.
BRANCH=none
BUG=chrome-os-partner:61671
TEST=on hammer (stm32f072)
flashinfo => RO+RW not protected
flashwp true; reboot => only RO protected
flashwp all; reboot => RO+RW+RB protected
flashwp noall; reboot => only RO protected
flashwp rw; reboot => only RO+RW protected
flashwp rb; reboot => RO+RW+RB protected
flashwp norb; reboot => RO+RW protected
flashwp all; reboot => RO+RW+RB protected
flashwp norw; reboot => RO+RB protected
TEST=on reef, rb/norb commands not available
Change-Id: I45ffc66d91cf3699ecff025e5114c59a73dc8274
Reviewed-on: https://chromium-review.googlesource.com/430519
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Add generic routines to read or write a byte to battery-backed RAM, and
implement vbnvcontext get/set using these routines.
BUG=chrome-os-partner:62952
BRANCH=reef
TEST=On reef, with subsequent commit, run "cutoff" on the console,
reattach AC, and verify device successfully wakes. Also verify Rp is
dropped on console 'reboot' and F3 + power from RW.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I14691923f2e5198e901b6b5199e92c58c68cd18d
Reviewed-on: https://chromium-review.googlesource.com/444444
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The idea of this flag is to be able to protect/unprotect only the
RW portion of the flash. In the (usual) case where ALL=RO+RW, with
no other region, this makes no difference compared to the existing
EC_FLASH_PROTECT_ALL_* flag, and this flag may not be supported.
This is necessary for futher work, where a ROLLBACK region is added,
so that RW/ROLLBACK can be protected/unprotected individually.
Only support for stm32f0 is added, as this is the target for hammer.
BRANCH=none
BUG=chrome-os-partner:61671
TEST=build and flash hammer (stm32f072)
flashinfo => RO+RW not protected
flashwp true; reboot => only RO protected
flashwp all; reboot => RO+RW protected
flashwp noall; reboot => only RO protected
flashwp rw/norw not available
TEST=enable CONFIG_FLASH_PROTECT_RW
build and flash hammer (stm32f072)
flashinfo => RO+RW not protected
flashwp true; reboot => only RO protected
flashwp all; reboot => RO+RW protected
flashwp noall; reboot => only RO protected
flashwp rw; reboot => RO+RW protected
flashwp norw; reboot => only RO protected
TEST=build and flash reef (npcx)
flashinfo => RO+RW not protected
flashwp true => RO protected
flashwp all; flashinfo => all_now displayed
reboot => RO protected
flashwp rw/norw not available
Change-Id: Ica6f499cf2e8a9345b08ef52c915655a983ffe3c
Reviewed-on: https://chromium-review.googlesource.com/442265
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Keep only the most compact version of the curve25519 code
and remove the remaining unused code for easier compilation.
Do the minimal changes to make it compile in the EC code base,
there should be no real functional changes.
Re-use the wording from BoringSSL include/openssl/curve25519.h for the
header.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:62991
TEST=run x25519 on host (ie 'make run-x25519')
and the STM32L4 target:
make BOARD=eve_fp PROJECT=x25519 TEST_BUILD=y
./util/flash_ec --board=eve_fp --image=build/eve_fp/x25519.bin
execute 'runtest' in the console.
Change-Id: I13dbe453eff39b461effb1b3ffa549afc1749fef
Reviewed-on: https://chromium-review.googlesource.com/444187
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Adam Langley <agl@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Previously, wiping the TPM would wipe all of NvMem, however, it really
should only clear the TPM's NvMem space. This commit adds a function to
clear a given NvMem user's space and makes the TPM only clear its space.
BUG=chrome-os-partner:61597
BRANCH=None
TEST=Add code for using nvmem vars, create a test variable, add a user
to snappy, unlock the console, verify that the user is no longer present
on the system and the test nvmem var still exists.
TEST=make -j buildall
Change-Id: Ic98baa5166a1ef9ae76e910b1b9ab100300e947f
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/445803
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
All host commands must be 4-digit uppercase hex digits.
The current ACPI host commands are defined as follows:
#define EC_CMD_ACPI_READ 0x80
#define EC_CMD_ACPI_WRITE 0x81
#define EC_CMD_ACPI_BURST_ENABLE 0x82
#define EC_CMD_ACPI_BURST_DISABLE 0x83
#define EC_CMD_ACPI_QUERY_EVENT 0x84
BUG=chrome-os-partner:63190
TEST=make -j buildall
100bd248 R __host_cmd_0x00000x0080
100bd254 R __host_cmd_0x00000x0081
100bd260 R __host_cmd_0x00000x0082
100bd26c R __host_cmd_0x00000x0083
100bd278 R __host_cmd_0x00000x0084
BRANCH=none
Change-Id: I48ad9c179454eb237018377023bae10a79c7799e
Reviewed-on: https://chromium-review.googlesource.com/445809
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Current code puts key at the end of the first half of flash, which
may not match the actual RO section size (e.g., it might be PSTATE,
not RO). This makes sure the key to be at the end of RO section, and
signature at the end of RW section, no matter the actual layout
being used.
However, the (deprecated) usbpd1 image type assumes that flash is
equally split between RO and RW, so we do not change that.
BRANCH=none
BUG=chrome-os-partner:61671
TEST=make BOARD=hammer -j && deploy
TEST=make BOARD=hoho -j && \
futility show --type usbpd1 build/hoho/ec.bin
Change-Id: Ia02e927f9128d6ec3d0b780c28312e0d18835d72
Reviewed-on: https://chromium-review.googlesource.com/426100
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Eve P1 is missing the ALS_INT_L signal and so needs to poll the
Si114x. This CL adds a new config option CONFIG_ALS_SI114X_POLLING
that when defined uses a deferred callback to trigger the motion
sensor event that reads sensor registers. The deferred callback uses a
8 msec delay which is ~2x longer than the time required by the sensor
to complete the measurement.
BUG=chrome-os-partner:61470
BRANCH=none
TEST=On Eve verify that light sensor measurments are present with the
'accelinfo on 1000' command.
Change-Id: I212bebf2ceacbac87ccb0734cc4990dbc349b028
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/440377
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
The USB FW upgrade endpoint should really only accept vendor commands
required to perform the firmware update. This commit adds a whitelist
that is checked whenever a vendor command is received over this
endpoint.
The allowed commands over USB are the following:
- EXTENSION_POST_RESET
- VENDOR_CC_IMMEDIATE_RESET (only for dev images)
There is also functionality to have a whitelist for vendor commands that
come over the TPM interface.
BUG=chrome-os-partner:62815
BRANCH=None
TEST=Flash Cr50 with image containing this change. Verify that an
upgrade over USB to newer image works.
TEST=Try using usb_updater to send a vendor command that's not in the
whitelist. Verify that the vendor command is dropped.
Change-Id: I71f8ba090a1cc6c9e7c30ce0dd3c25259e8f292f
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/443447
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Currently, manually triggered reboots cause the retry counter to be
incremented. However, if the system is responsive enough to process the
reboot commands from either the console or TPM vendor command, we can
assume that the image is "ok". This commit changes the Cr50 behaviour
to decrement the retry counter when a reboot is issued on the console or
the TPM vendor command is received.
BUG=chrome-os-partner:62687
BRANCH=None
TEST=Flash cr50. Flash an older image in the other slot. Enter the
reboot command on the console over 10 times and verify that retry
counter never exceeds RW_BOOT_MAX_RETRY_COUNT and older image is never
executed.
CQ-DEPEND=CL:444264
Change-Id: Ic35bdc63c4141834584a00a7ecceab2abe8dfc21
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/443330
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
usbpd1 futility image type is deprecated and should not be used for
new designs. This adds proper support for rwsig image type.
Key and signatures are added at linker stage step (futility cannot
directly create such signed images). Thanks to VB21 header, rwsig.c
can now tell how many bytes of the RW image need to be
cryptographically verified, and ensure that the rest is blank (0xff).
BRANCH=none
BUG=chromium:690773
TEST=make BOARD=hammer; flash, RW image is verified correctly.
TEST=make runtests -j
TEST=For the rest of the tests:
Change config option to CONFIG_RWSIG_TYPE_RWSIG
TEST=make BOARD=hammer; flash, hammer still verifies correctly.
TEST=cp build/hammer/ec.RW.bin build/hammer/ec.RW.bin.orig;
futility sign --type rwsig --prikey build/hammer/key.vbprik2 \
build/hammer/ec.RW.bin
diff build/hammer/ec.RW.bin build/hammer/ec.RW.bin.orig
=> Same file
TEST=Add CONFIG_CMD_FLASH, flashwrite 0x1e000, reboot, EC does
not verify anymore.
TEST=dump_fmap build/hammer/ec.bin shows KEY_RO and SIG_RW at
correct locations.
Change-Id: I50ec828284c2d1eca67fa8cbddaf6f3b06606c82
Reviewed-on: https://chromium-review.googlesource.com/441546
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Use the motion sensor to manage ALS as well.
The current interface (via memmap) is preserved, but
we can also access the sensor via cros ec sensor stack and
send the ALS information to ARC++.
BUG=chrome-os-partner:59423
BRANCH=reef
CQ-DEPEND=CL:424217
TEST=Check the sensor is working via ACPI sensor and
cros ec sensor. Check ARC++ sees the sensors.
Change-Id: Iaf608370454ad582691b72b471ea87b511863a78
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/424323
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
This change adds an option to pdchipinfo command to force ec to get
the version from the chip instead of the cache (if it's available).
This option will be used after firmware update, which makes the cache
value stale.
BUG=chrome-os-partner:62383
BRANCH=none
TEST=Run ectool as follows:
localhost ~ # /tmp/ectool pdchipinfo 0 on
vendor_id: 0xaaaa
product_id: 0x3429
device_id: 0xad
fw_version: 0x15
localhost ~ # /tmp/ectool pdchipinfo 1 on
EC result 2 (ERROR)
Change-Id: Icefe96d7fc1208b991a4caa13aaf4f04052edba7
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/441271
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The firmware version formats may vary chip to chip. fw_version field is
changed to a union of a 8 byte string and an 64-bit integer.
BUG=chrome-os-partner:62383
BRANCH=none
TEST=ectool pdchipinfo 0/1 on Electro
Change-Id: Id51e66c44338a09ed897ee61f54cd6a394400e63
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/441270
Make FIFO a stack variable to save static memory,
Remove auto_inc argument, always set
Remove constant for rate 0.
Force board to declare sensor private data.
Avoid name collision in stm_mems_common
Include stm_mems_common.h in accel_lis2dh.h, caller only need to
include accel_lis2dh.h.
BUG=none
BRANCH=none
TEST=Compile with discovery_stmems board.
Change-Id: Id52b54dd4ec3cf217247c5511ad5a506067ad293
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/441144
Tested-by: mario tesi <mario.tesi@st.com>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: mario tesi <mario.tesi@st.com>
In preparation for adding the rollback protection block, pass
EC_FLASH_PROTECT_RO/ALL_AT_BOOT to flash_[physical_]protect_at_boot,
instead of an enumeration no protection/RO/ALL.
This will later allow us to protect/unprotect the rollback region only,
by adding a EC_FLASH_PROTECT_ROLLBACK_AT_BOOT flag.
BRANCH=none
BUG=chrome-os-partner:61671
TEST=Build hammer with CONFIG_CMD_FLASH command, so that write protection
can be checked with flasherase/flashwrite.
TEST=On hammer (stm32f072):
flashinfo => RO+RW not protected
flashwp true; reboot => only RO protected
flashwp rw; reboot => RO+RW protected
flashwp norw; reboot => only RO protected
TEST=On reef (npcx):
deassert WP, flashwp false; flashinfo => RO+RW not protected
flashwp true => only RO protected
reboot => only RO protected
flashwp rw => RO+RW protected
reboot => only RO protected
Change-Id: Iec96a7377baabc9100fc59de0a31505095a3499f
Reviewed-on: https://chromium-review.googlesource.com/430518
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This removes CONFIG_USB_PD_TCPC_FW_VERSION.
board_print_tcpc_fw_version is removed since it's no longer called.
PD chip info is printed in usb_pd_protocol.c.
BUG=none
BRANCH=none
TEST=buildall. Boot Electro, verify chip info is printed.
Change-Id: I2ff860c2a1b17ceea124644ba8feb356b9cca2eb
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/434911
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Shorten certain long prints and reduce the precision of timestamp prints
when CONFIG_CONSOLE_VERBOSE is undef'd.
BUG=chromium:688743
BRANCH=gru
TEST=On kevin, cold reset the EC, boot to OS, and verify cros_ec.log
contains all data since sysjump and is < 2K bytes (~1500 bytes).
Change-Id: Ia9390867788d0ab3087f827b0296107b4e9d4bca
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/438932
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Current fast charge assumes only one battery voltage threshold range for
charger profile override. However we have multiple battery voltage
threshold ranges for few batteries hence added a code which can consider
multiple battery threshold ranges and choose respective charge profile.
BUG=chrome-os-partner:62653
BRANCH=none
TEST=Manually tested on Electro. Manipulate smp_cos4870 & sonycorp
battery voltage & temperature ranges and observed correct charge
profile is selected.
Change-Id: Icddc047e608cc8f63cd0c19be716e0f7908ca715
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/438804
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds a host command to get PD chip info.
For PS8751, tcpci_get_chip_info will fail if the chip is in
low power mode. It can be woken up by reading a random register
first then wait for 10ms.
This code doesn't have the wake-up read to avoid 10ms delay.
Instead, we call this function immediately after the chip is
initialized because it'll gurantee the chip is awake.
Once it's called, the chip info will be stored in cache, which
can be accessed by tcpc_get_chip_info without worrying about
chip states.
localhost ~ # ectool pdchipinfo 0
vendor_id: 0xaaaa
product_id: 0x3429
device_id: 0xad
fw_version: 0x15
localhost ~ # ectool pdchipinfo 1
vendor_id: 0x1da0
product_id: 0x8751
device_id: 0x1
fw_version: 0x37
BUG=chrome-os-partner:62383
BRANCH=none
TEST=ectool pdchipinfo 0/1. make buildall
Change-Id: I3f1667d00ce1826936d90882ada1df6ed6b0ea37
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/433166
In case there is a sudden power loss to PCH, then there are no eSPI VW
messages sent from the PCH to EC indicating power state transition into
S5. Instead, the eSPI compatibility spec defines such events as global
reset events. For global reset events, eSPI_Reset# signal is asserted
without SLP_SUS# being asserted. This acts as an indication to the EC
that there was a global reset event.
Add a callback chipset_handle_espi_reset_assert that takes any necessary
action whenever eSPI_Reset# pin is asserted. On skylake, it would check
if power button was being pressed and release the button.
BUG=chrome-os-partner:62014
BRANCH=None
TEST=Verified that apshutdown works as expected.
Change-Id: I409afa0d00faca55ae3aa577743cedac58d4d877
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/438935
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add driver for acc sensor ST lis2dh/lis2dh12
Support interrupt management for FIFO watermark
Starting to share common code with other devices
like lsm6dsm/lsm6dsl (acc/gyro) or new lis2mdl (mag)
TODO: Add all embedded functions support (click,
tap and so on)
BUG=none
BRANCH=master
TEST=Tested on discovery BOARD with sensor connected on
EC i2c master bus. Added motion sense task on discovery
board task list, added gpio info in board configuration
file and tested with motion sense console commands. Data
for acc seems ok: can successfully change ODR and
full scale range. Also FIFO and interrupt tested
Device tested is lis2dh (lis2dh12 simply differs for low
pin count but share the same registers)
Change-Id: I16abeac3f139a604094b38d8d8b857a62c93a242
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Reviewed-on: https://chromium-review.googlesource.com/412700
Commit-Ready: mario tesi <mario.tesi@st.com>
Tested-by: mario tesi <mario.tesi@st.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
If CONFIG_SPI_NOR_SMART_ERASE is defined will read the sector/block
to be erased first and only initiate the erase operation if not
already in an erased state. The read operation (performed in
CONFIG_SPI_NOR_MAX_READ_SIZE chunks) is aborted early if a
non "0xff" byte is encountered.
Reduced erase time of a mostly erased EEPROM from 44s to 20s (16MB
Winbond part) / 1m22s to 40s (32MB Macronix part) @24MHz.
BUG=None
BRANCH=None
TEST=Built all targets. Successfully flashed various EEPROM images.
Change-Id: I369b1fcf72140663b8dbce5a469ebad27f7571ec
Signed-off-by: Nadim Taha <ntaha@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/437988
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
There is no point in keeping in one file multiple hooks task callbacks
to handle chipset shutdown and resume conditions.
Also, the policy of disabling deep sleep needs to be decided in the
board level hooks.
BRANCH=none
BUG=chrome-os-partner:59007
TEST=ran reef through 200 cycles of suspend/resume
Change-Id: I4d30cd04b986b243a5bea44c6978a5f82f8f62a7
Reviewed-on: https://chromium-review.googlesource.com/437729
Reviewed-by: Scott Collyer <scollyer@chromium.org>
Commit-Queue: Vadim Bendebury <vbendeb@chromium.org>
Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Trybot-Ready: Vadim Bendebury <vbendeb@chromium.org>
The cr50 needs to be aware of the power state of the system and of the
moment when the AP is reset, because this is when the TPM needs to be
reset too.
Arm and x86 platforms provide different hints in these cases.
In case of x86 there is a single signal cr50 can rely on: PLT_RST_L.
This active low signal is asserted when the system is going into any
power state deeper than s0ix. The cr50 can fall into deep sleep when
PLT_RST_L is asserted, and has to wake up and reset the TPM when this
signal is deasserted. There could be other wake triggers, but the tpm
should not be reset unless PLT_RST_L is inactive. It is also important
not to fall into deep sleep when PLT_RST_L is pulsed to reboot the
system.
In case of ARM there are two separate signals. Deasserting SYS_RST_L
signal is the trigger to reset the TPM, The GPIO_DETECT_AP going low
for a duration of time is the indication of the AP going into some
kind of sleep mode. The ARM case requires more clarification.
This adds run time configuration of the the sleep state control input.
Once the input turns low, the CHIPSET_SHUTDOWN signal is sent and deep
sleep mode is enabled. Again, this will require adjustment for ARM
platforms.
The wake from deep sleep state is controlled by the wake pins as
before, but by level instead of edge. This makes sure that in case the
trigger for deep sleep goes away while deep sleep preparation is under
way, the device resumes immediately instead of getting stuck missing
the edge.
The TPM_RST_ input is now triggering interrupts on deassertion
- this is the moment when the TPM needs to be reset. The ISR is being
renamed accordingly.
The processing previously happening inside the ISR is being moved into
a deferred function running on the hooks task context.
There is no need to invoke TPM reset related functions from the PMU
wake up ISR anymore.
BRANCH=none
BUG=chrome-os-partner:59007
TEST=as follows:
1. make buildall -j succeeds
2. started on Reef, still in progress after 100 iterations, early to
call
suspend_stress_test --suspend_min 40 --suspend_max 45 \
--wake_max 15 wake_min 10
(note that reef does not fall into s3 any more, so the test does not
verify H1 deep sleep)
3. modified the target to fall into s3 during the test and
successfully repeated it for 100 iterations
4. tried battery disconnect a few times and observe successful boot.
Change-Id: Ica06ec0d363b53eede3be327404ff5807fa3a610
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/436865
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
All boards have been transitioned to charge_state_v2.c
So charge_state_v1.c, HOOK_CHARGE_STATE_CHANGE, and
CONFIG_CHARGER_TIMEOUT_HOURS can be removed
BUG=chrome-os-partner:36272
TEST=make -j buildall
BRANCH=none
Change-Id: I3f20c5198ea75185f9894deb792575a1be31432a
Reviewed-on: https://chromium-review.googlesource.com/435467
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
The INAs are only used for development and testing
purposes. Therefore, the 3.3V rail to the INAs is off by default and
the I2Cm module is not enabled. Enabling INA power and connecting the
I2Cm module was done at the beginning of each USB to I2C request. The
problem with this approach is that INA measurments didn't always
succeed due to not enough time for the INAs to initialize.
Rather than add some arbitrary delay, it is better to tie the INAs to
when rdd is attached/detached. It is only when rdd is attached that
the INAs will be accessed, so there is no need to enable/disable for
each individual I2C transaction.
This CL ties the enabling/disabling of the INA and I2Cm module to the
rdd state. This change makes the previous use of
usb_i2c_board_enable() and usb_i2c_board_disable() obslete.
BRANCH=none
BUG=chrome-os-partner:62375
TEST=manual
Connect servo with suzyq connected:
sudo servod -p 0x5014 -b eve -c eve_r0_inas.xml
Then execute single INA reads dut-control pp3300_dx_edp_mv and verify
that it returns meaningful numbers. Without this CL single reads via
dut-control would always return 0.
Change-Id: I799552bfd0701efd1828a0d720ac2a6cedee5ca1
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/436864
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
During shutdown sequence sensor rails can be powered down asynchronously
to the EC hence EC cannot interlock the sensor states with the power down
states. To avoid this issue, defer switching the sensors rate with a
configurable delay if in S3. By the time deferred function is serviced,
if the chipset is in S5 we can back out from switching the sensor rate.
BUG=chrome-os-partner:61489
BRANCH=none
TEST=Manually tested on Electro. Put the device in S5 and observed
no I2C errors printed on EC the console.
Change-Id: I40b75ebbf0d05fafffdfd535962423c3960fafbf
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/433338
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
charge_ramp needs to make a decision based upon the VBUS level on one
specific port - the port that is ramping. The VBUS level on any other
charge ports (if present) is not relevant.
BUG=chrome-os-partner:54099
BRANCH=reef, gru
TEST=With subsequent patches, verify charge_ramp success with a variety
of BC1.2 chargers.
Change-Id: Ie0a51a577e2b7491222560cd08dd5321ff3b7975
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/435561
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Values should be as follows:
tTypeCSinkWaitCap: 310 to 620ms
tPSHardReset: 25 to 35ms
Current values are:
tTypeCSinkWaitCap (PD_T_SINK_WAIT_CAP): 240ms
tPSHardReset (PD_T_PS_HARD_RESET): 15ms
BUG=chromium:686122
TEST=manual testing on kevin along with make -j buildall
- used a kevin to send a hard reset to uut
> pd 0 hard
C0 st36
C0 st37
34725 ms <-- time it took hard reset to execute
C0 HARD RST TX
- used a kevin, operating as source, that does not send
source caps to test a uut operating as a sink.
C0 st6
C0 st36
613266 ms <-- time sink waited for source cap
- plugged in charger and logged pd negotiation
[1510.574091 event set 0x00200000]
C0 st15
C0 st3
[1510.845115 event set 0x08000000]
C0 st6
Req C0 [1] 5000mV 3000mA
[1510.945827 New chg p0]
C0 st7
[1510.949953 CL: pC0 st8
0 s0 i500 v15000]
[1510.954055 event set 0x00200000]
[C0 st9
1511.061285 event set 0x00400000]
[1511.064752 CL: p0 s0 i3000 v5000]
[Req C0 [3] 15000mV 3000mA
1511.067538 event set 0x00200000]
C0 st7
C0 st8
[1511.077896 CL: p0 s0 i500 v5000]
[1511.079048 event set 0x00200000]
C0 st9
[1511.275448 CL: p0 s0 i3000 v15000]
[1511.276913 event set 0x00200000]
Req C0 [3] 15000mV 3000mA
[1511.445719 CL: p0 s0 i500 v15000]
[1511.446117 event set 0x00200000]
C0 st7
C0 st8
C0 st9
[1511.565730 CL: p0 s0 i3000 v15000]
[1511.566566 event set 0x00200000]
[1511.812205 event set 0x00400000]
[1513.274941 event set 0x00200000]
[1529.324670 Battery 90% / 0h:29 to full]
BRANCH=none
Change-Id: I6e80637cfc50dcfc431feb0e473ec22f408d6f1a
Reviewed-on: https://chromium-review.googlesource.com/434103
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
All host commands must be 4-digit uppercase hex digits.
EC_CMD_HOST_EVENT_GET_WAKE_MASK is currently defined as 0x008d
BUG=chrome-os-partner:62518
TEST=make -j buildall
100bcffc R __host_cmd_0x00000x0087
100bd008 R __host_cmd_0x00000x008C
100bd014 R __host_cmd_0x00000x008D
100bd020 R __host_cmd_0x00000x008F
100bd02c R __host_cmd_0x00000x0092
BRANCH=none
Change-Id: If2460efa7453e8007514b10dd9a973120006c7e1
Reviewed-on: https://chromium-review.googlesource.com/435581
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Store our image size (known at build time) in our version struct (now
renamed to image_data). This will allow us to more efficiently determine
the size of an image in a follow-up CL.
Note that compatibility is broken for old ROs that do not include this
CL.
BUG=chromium:577915
TEST=Verify on kevin + lars + lars_pd that stored image size matches
output of system_get_image_used() for both RO and RW images.
BRANCH=None
Change-Id: I49ea5fc27a7f11f66daba485a87d0dfe7d0c770f
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/427408
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This vendor command allows the host to retrieve the internal TPM
state. The first version of the command will return the failure
information collected during assert, if it ever happened, retry
counter value and the maximum retry counter value to be able to detect
if TPM is in lockout.
The structure is packed, it is serialized before being sent to the
host.
BRANCH=none
BUG=chrome-os-partner:60555
TEST=when running on a reef with a depthcharge image capable of
displaying TPM state on errors observed state information added
to the recovery screen text display.
Change-Id: I9d37f7a971013ce802f63218d43697fab68276c9
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/430952
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Andrey Pronin <apronin@chromium.org>
tpm_reset just requests a tpm reset it doesn't reset the tpm. Rename the
function to reflect that.
BUG=none
BRANCH=none
TEST=make buildall
Change-Id: I6f4763b5de578a8cf263b2fac98fad3af2c25d65
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/434245
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
With introduction of encryption it is becoming impossible to read
NVMEM contents directly from flash. Decrypting the contents each time
there is a read request creates a significant performance hit. NVMEM
needs to be rearchitecture such that there is no need to run
decryption each time NVMEM read is performed.
This patch does just that, implementation details are described in the
header comment in common/nvmem.c.
To reduce memory impact the size of NVMEM is being decreased from 16K
to 12K. This is acceptable because eviction objects stored in NVMEM
serialized now, which dramatically reduces NVMEM size requirements.
The TPM2 NVMEM size definition must be kept in sync.
Another optimization this change introduces is bypassing writing into
the flash if NVMEM contents did not change, which is verified by
examining the hash of the cached storage.
A test is added to verify that the new commit scheme works as
expected, and the nvmem test is re-introduced to the list of test ran
on each 'make buildall'.
CQ-DEPEND=CL:433839
BRANCH=none
BUG=chrome-os-partner:62260,chrome-os-partner:62421
BUG=chrome-os-partner:62437
TEST=ran the following tests, all succeeded
make buildall -j
TEST_LIST_HOST=nvmem make runtests
tcg test suite
corp enroll on reef, reboot a few times, verify that enrollment sticks
Change-Id: I177daa3ceb4fd7aac299ca26b4506b863e31b946
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/433184
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Modified src attach state to enable vbus when debug accessory is
detected.
- servo_v4 has two pd ports, but each port requires a different default
power role. Port 0 can only ever be a SNK, but port 1 which acts is
intended to be a DTS port should default to a SRC so it can be be a
source debug accessory. It may also act as a sink debug accessory, but
is not intended to toggle automatically but will swap roles if
necessary via pd role swap messaging.
- Add hook for ccd enable/disable for DTS mode
BUG=chrome-os-partner:61878
BRANCH=servo
TEST=Manual Verfied that can still build servo_v4 project. All changes
in this CL are contingent on config option CONFIG_USB_PD_DTS being enabled.
Change-Id: Iab968b6fbdfc8f2d155c4f8618921b32f313b9ec
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/428308
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In Sink mode, on the receipt of a GotoMin message,
reduce the current consumption to some minimum level.
BUG=chrome-os-partner:33688
TEST=Manual testing
Used a Kevin, with test routine, to test GotoMin feature
on another Kevin unit.
Test routine:
if (!strcasecmp(argv[2], "gm")) {
ccprintf("send goto min\n");
send_control(port, PD_CTRL_GOTO_MIN);
send_control(port, PD_CTRL_PS_RDY);
}
Kevin with GotoMin feature:
# ectool usbpdpower 0
Port 0: SNK DRP PD 4277mV / 3000mA, max 5000mV / 3000mA / 15000mW
Port 1: Disconnected
After Test routine is executed:
# ectool usbpdpower 0
Port 0: SNK DRP PD 4906mV / 500mA, max 5000mV / 500mA / 2500mW
Port 1: Disconnected
BRANCH=none
Change-Id: Iaac6e19706ceb10ccaff4d602d63fc086c808c8f
Reviewed-on: https://chromium-review.googlesource.com/425728
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Servo_v4 requires the ability to have a different default state per
port. In previous devices, the assumption was that each supported port
had the same default usb pd state and power role. This CL moves the
by the default power role which in turn is derived from
CONFIG_USB_PD_DUAL_ROLE. In addiiton to moving the location, it now
uses 'port' as argument so it can be port specific if required.
PD_DEFAULT_STATE was a board.h specific config, but in practice each
instance used to date was set to PD_STATE_SNK_DISCONNECTED if
CONFIG_USB_PD_DUAL_ROLE was defined and set to
PD_STATE_SRC_DISCONNECTED otherwise.
BUG=chrome-os-partner:61878
BRANCH=servo
TEST=Manual run 'make -j buildall' to verify that all instances of
PD_DEFAULT_STATE were removed.
Change-Id: Iaf40718668732f525485ed7942ee7fc246d3f75d
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/431787
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
(From CL 431233)
Limit battery charge voltage to prevent battery over-charge, due to
regulation inaccuracy. Since RO FW may charge > 8656 mV, ensure the
battery is not full before charging.
BUG=chrome-os-partner:61906
BRANCH=none
TEST=Manual on Electro, sysjump with battery @ 99%, verify battery
discharges, then re-charges to 100%, before discharging once again.
Change-Id: I28212c83057a442fd75e39f8ad51927a7a1f2817
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/432857
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch makes incompatible changes to the nvmem layout: the header
is increased to accommodate a 16 byte sha ans a 16 byte padding for
future extensions.
The layout version field is also introduced to make it easier to track
changes in the future. When calculating SHA the entire partition above
the SHA field is processed. Encryption covers everything above the
header.
Introducing encryption makes it impossible to use flash contents
directly for read and compare operations.
The nvmem_setup function is modified to use the nvnem_save() instead
of writing into the flash directly.
BRANCH=none
BUG=chrome-os-partner:62260
TEST=ran the following tests, all succeeded
make buildall -j
TEST_LIST_HOST=nvmem make runtests
tcg test suite
corp enroll on reef, reboot a few times, verify that enrollment sticks
Change-Id: I50b148ac0dc6bc924f4d65c67bc6610100d9dfc0
Reviewed-on: https://chromium-review.googlesource.com/428691
Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
