-Routing HPET1 timer requires HPET's General Config register's Legacy
routing bit should be set.
-For HPET0 interrupt, no need to set IRQ# to T0C register.
-change IRQ# back to default values.
BUG=None
BRANCH=master
TEST=`Build ISH and verify the timer interrupt via various
console cmds`
Change-Id: I9f83d62a1f7d999ebf6cedafd38691531ec91081
Signed-off-by: Kyoung Kim <kyoung.il.kim@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/627628
Commit-Ready: Kyoung Il Kim <kyoung.il.kim@intel.com>
Tested-by: Kyoung Il Kim <kyoung.il.kim@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change includes
- Configuring the HPET timer based on the spec
(IA-PC HPET (High Precision Event Timers) Specification 1.0a)
- Two timers used:
HPET Timer0 (free running periodic timer)
HPET Timer1 (event based non-periodic timer)
- HPET interrupts are routed to ISH via IOAPIC
- Both the timers are functional
BUG=None
BRANCH=None
TEST=`Build ISH and verify the timer interrupt via various console cmds`
Change-Id: Ib5ca24d05790868430a2cfa72ca73f5bd6a5fea3
Signed-off-by: Divagar Mohandass <divagar.mohandass@intel.com>
Signed-off-by: Kyoung Kim <kyoung.il.kim@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/453858
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add generic routines to read or write a byte to battery-backed RAM, and
implement vbnvcontext get/set using these routines.
BUG=chrome-os-partner:62952
BRANCH=reef
TEST=On reef, with subsequent commit, run "cutoff" on the console,
reattach AC, and verify device successfully wakes. Also verify Rp is
dropped on console 'reboot' and F3 + power from RW.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I14691923f2e5198e901b6b5199e92c58c68cd18d
Reviewed-on: https://chromium-review.googlesource.com/444444
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This patch adds the initial support for ISH chip to enable the EC
firmware to boot on Intel Integrated Sensor Hub (ISH). The following are
enabled:
1. Inter-Processor Communication (IPC) driver that enables the ISH to
communicate with the host Operating system via shared registers.
2. High Precision Event Timer (HPET) driver that provides configurable
timers for the FW to use in task scheduling.
3. I2C bus driver for accessing sensors.
4. UART console driver with TX support only.
BUG=chrome-os-partner:51851
BRANCH=None
TEST=`make buildall -j`
Change-Id: I15d4c201b799cfa79bed220ee573b75f5cd7b1f7
Signed-off-by: Jaiber John <jaiber.j.john@intel.com>
Signed-off-by: Alex Brill <alexander.brill@intel.com>
Signed-off-by: Gomathi Kumar <gomathi.kumar@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/336710
Commit-Ready: Raj Mojumder <raj.mojumder@intel.com>
Tested-by: Jaiber J John <jaiber.j.john@intel.com>
Tested-by: Raj Mojumder <raj.mojumder@intel.com>
Reviewed-by: Jaiber J John <jaiber.j.john@intel.com>
Reviewed-by: Raj Mojumder <raj.mojumder@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
