When the host sets rtc alarm wake time = 0, it wants
to reset and disable the alarm.
Also, align the implementation in npcx with that in stm32
to check both delay_s and delay_us.
BUG=b:66971951, b:63908519
BRANCH=none
TEST='ectool rtcsetalarm 3'. After alarm goes off, run
'ectool rtcgetalarm' and then see 'Alarm not set'.
Change-Id: I693f1c72cba492e837891c716f79e2aa4da59b2a
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/691256
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
To aid with severe flash space shortage, let's enable
CRYPTO_TEST_SETUP only if CR50_DEV is set to a value exceeding 1.
board/mn50/board.h used to define CR50_DEV without any value assigned
to it, correct this so that the check in dcrypto.h works when mn50 is
built.
BRANCH=cr50
BUG=b:65253310
TEST=compiling with CR50-DEV=1 vs CR50_DEV=2 saves more than
17.5 Kbytes per RW image.
Change-Id: Ic77fa45b1a8f7631efa91c08e63438d412196eed
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/690993
Reviewed-by: Randall Spangler <rspangler@chromium.org>
If we don't use IT8320's PD module, we should dis-connect resistor
to GND and disable CC related function to make sure these pins can
work as other function.
BRANCH=none
BUG=none
TEST=CCCSR register setting is 0xff after initialization if
we don't enable CONFIG_USB_PD_TCPM_ITE83XX.
Change-Id: I97e019ec1c9c852cd758b364a5e7913de1fc84f4
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-on: https://chromium-review.googlesource.com/689435
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In npcx7, we introduced a new bit, VWUPDW, in ESPISTS register to
indicate a Master-to-Slave VW signal was updated and the relevant WE
bit is 1. But there's no relevant IE bit in ESPIIE for VWUPDW, old
mechanism for clearing pending bits of ESPISTS will ignore this bit.
And ec cannot enter deep sleep anymore since this bit is set. This CL
fixed this bug by setting bit 17 of mask variable if ec is npcx7 series.
BRANCH=none
BUG=none
TEST=No build errors for npcx5/7 series.
Change-Id: I80c57d3c230e9d06ba134538ccdcd29f290bb7bf
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/672183
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Amit Maoz <Amit.Maoz@nuvoton.com>
In this CL, we introduced new bit fields of eSPI registers on npcx5/7
for the incoming patches. We also remove useless registers such as
VWGPMS, VWGPSM and PING in order to let the driver look more clearly.
This CL also includes:
1. Fixed typo from ESPIIWE to ESPIWE.
2. Introduce ESPIWE bits fields on npcx5/7.
3. Introduce new bit fields in ESPISTS of npcx7.
4. Remove useless VW1-4, VW1IE1-4 bits in ESPISTS and ESPIIE registes.
5. Introduce new bit field, WE, in VWEVMSn register of npcx7.
BRANCH=none
BUG=none
TEST=No build errors for npcx5/7 series. Using "suspend_stress_test -c
1000" to do stress test and no symptom occurred on poppy. Both warmboot
and coldboot stress test for 3 hours and no symptom occurred on poppy.
Change-Id: Ie8aa3dbd148588b0d9a756572d66604a6836a760
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/672026
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Amit Maoz <Amit.Maoz@nuvoton.com>
The current stm32 rtc driver only uses RTC_TR and RTC_SSR.
So we son't be able to use rtc for applications which need
time > 24 hours.
To support such applications, this patch adds operations
for RTC date register (RTC_DR).
BUG=b:63908519
CQ-DEPEND=CL:666985
BRANCH=none
TEST=manually with 'ectool rtcset/rtcset' and '/sys/class/rtc/rtc0',
verify the conversion between calendar time and Unix epoch time works.
Change-Id: Iacd5468502e4417a70880d7239ca5e03353d9469
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/659337
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The array storing deltas between sequential prime numbers could be
compressed, as the vast majority of the values in the array does not
require more than 4 buts to store.
The new storage format is as follows:
- each differential value (difference between two consecutive primes)
is halved and stored in 4 bits, two halved values are packed per
byte.
- I the first one of of the two sequential halved values exceeds 0xf,
it is stored in the array followed by a zero, stored as is (without
halving), thus taking two bytes.
- if the second one of the two sequential halved values exceeds 0xf,
both values are stored in the array as is, both prepended by zeros,
thus taking 4 bytes.
The code calculating the sequential primes parses the array according
to this format. Storing the primes in this format allows to shave from
the image size 1848 bytes.
BRANCH=cr50
BUG=b:65253310, b:65287300
TEST=verified that test_rsa test from the tpmtest suite passes.
verified that the list of prime numbers printed out when
PRINT_PRIMES is defined and test_rsa is ran is the same before
and after this patch.
Change-Id: Ifdc2858a48f868ef816ccb4e351d9f60703d16e7
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/664253
Reviewed-by: Nagendra Modadugu <ngm@google.com>
- To i2c channel(d/e/f), we remove instructions that aren't necessary.
- Changes of i2c_reset():
Before the change, we try to send a START/STOP bit if we get a reset.
But i2c_unwedge() already done it, so we just need reset i2c module
in i2c_reset().
- Add enhanced_i2c_start() to channel(d/e/f) for each transaction start:
We prepare transaction start by calling i2c_reset(),
but this doesn't match the definition of i2c_reset(),
so we correct it.
BRANCH=none
BUG=none
TEST=1. console commands: "i2cscan", "charger" and "battery".
2. sensors, battery, charger and mux work on reef_it8320.
Change-Id: I4e3595479e04a5994a5b19409cfc4e9a46f63d4f
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-on: https://chromium-review.googlesource.com/674467
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This change is required to reboot the chip without bringing down the
entire platform on boards where GPIOs are wired to external active reset
signals.
BRANCH=none
BUG=none
TEST=Scoped a pin across a reset.
Change-Id: I58d93697d39a8adcdac9324d5dd9da00745aec9a
Signed-off-by: Nadim Taha <ntaha@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/644179
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
When compilation is enabled, this function prints all prime numbers
generated using the PRIME_DELTAS array.
BRANCH=cr50
BUG=none
TEST=verified that prime numbers are printed out when running rsa_test.py
Change-Id: I37961aad146c4aeecca9a84550f313450e6c5853
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/683074
Reviewed-by: Shawn N <shawnn@chromium.org>
The WebUSB specification defines a specific Platform Descriptor in the
Binary Object Store:
https://wicg.github.io/webusb/#webusb-platform-capability-descriptor
This descriptor provides a special 'Landing page' URL to the host
browser and associated privileges for it.
Bump the USB version for BOS descriptors to 2.1 to be compatible with
Chrome implementation.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BUG=none
BRANCH=twinkie
TEST=manual: on Twinkie (chip/stm32) and HG proto2 (chip/g), enumerate
WebUSB descriptors with lsusb and connect to a WebUSB page in Chrome
R61+.
Change-Id: I7211ab554f4a6c156c1e8e79a3d9f0d6644217c6
Reviewed-on: https://chromium-review.googlesource.com/664813
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In the USB 2.0 specification, the "8.5.3 Control Transfers"
chapter says that "When all of the data structure is returned to the host,
the function should indicate that the Data stage is ended by returning a
packet that is shorter than the MaxPacketSize for the pipe. If the data
structure is an exact multiple of wMaxPacketSize for the pipe, the function
will return a zero-length packet to indicate the end of the Data stage."
When doing a 'Control Read' transfer and the returned data (in IN
packets) was a multiple of MaxPacketSize, we were omitting the
zero-length packet and so the host was blocked waiting for a successful
IN transaction.
This corner-case was a regression introduced by the re-writing of the
control transfer handling done by CL 318864. So the STM32 USB code which
is similar to the former code is dealing properly with this case.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=cr50
BUG=none
TEST=manual, extend the configuration descriptor to be exactly 64 bytes,
and see the enumeration is no longer failing.
Change-Id: I108e8c6bb9eb727c41f3e1c607f0919fa1192d5a
Reviewed-on: https://chromium-review.googlesource.com/664814
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Marius Schilder <mschilder@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
lsusb scans for USB_DT_DEBUG, which produces logspam
on the cr50 console. This isn't an error, just unimplemented.
Remove the printout.
BRANCH=cr50
BUG=b:65407184
TEST=no logspam on lsusb
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Change-Id: Ib4fc7105015506927f45ee02f587f97e46e1ad9b
Reviewed-on: https://chromium-review.googlesource.com/663786
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
For historical reasons, CCD, reset, and power button control were
scattered around several files. Consolidate the code in more sensible
(in retrospect) places.
No functional changes, just moving code.
BUG=none
BRANCH=cr50
TEST=make buildall; boot cr50
Change-Id: Ic381a5a5d0627753cc771189aa377e88b81b155e
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/653766
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
We disable i2c interface immediately after stop bit is set.
This might caused bus busy bit of status register unable to clear
(bus busy bit will be set at start condition and cleared at
stop condition).
So the next transaction, we won't get a good state to start.
This change also fix incorrect stop bit for write transaction:
IT83XX_I2C_CTR(p_ch) = xx
BRANCH=none
BUG=none
TEST=Ensure i2c interface is disabled after i2c stop condition.
Change-Id: I5416bfcef3f95357c6771dead6b0611b908f787e
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-on: https://chromium-review.googlesource.com/645407
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Default setting of embedded flash's clock is 24 or 32 MHz
and PLL is 48 or 96 MHz correspondingly.
And it8320 supports e-flash clock up to 48 MHz,so we add
a new config option to support it.
BRANCH=none
BUG=none
TEST=Run FAFT with e-flash 48MHz and test results are passed.
Change-Id: I096ae3abc8fec9bd7e0556c57605e87a31ac3b07
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-on: https://chromium-review.googlesource.com/645466
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In USB FS on a bulk/interrupt endpoint, the transactions normally toggles
between DATA0 and DATA1 PIDs.
After a USB suspend/resume cycle, we need to restart from the PID we
were at before suspend.
In our current code, when going to deep-sleep during USB suspend, we are
re-initializing everything when the MCU restarts at each resume. So we set
implicitly the PID to DATA0. The USB Hardware IP just silently discards the
packet when the PID of an incoming OUT packet is not matching the
expectation in the endpoint register.
In order to preserve DATA PIDS, record the state of the PID toggling on
each endpoint when going to deep-sleep and restore it during the USB
initialization.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:38160821
TEST=manual, plug a HG proto2 on a Linux host machine and enable
'auto-suspend' for this USB device. Let it go to sleep and wake-it up by
sending a U2FHID request. Repeat the process several times and see that
the key answers every time (while it was failing after the second cycle
before).
Change-Id: I75e2cfc39f22483d9e9b32c5f8b887dbafc37108
Reviewed-on: https://chromium-review.googlesource.com/655238
Commit-Ready: Marius Schilder <mschilder@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Marius Schilder <mschilder@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Currently, the Cr50 state machines (EC, AP, RDD, bitbang, etc.) manage
their own enabling and disabling of the ports (UART, SPI, etc.) This
is tricky because the rules for when ports should be enabled are
non-trivial and must be applied in the correct order. In additionl
the changes all need to be serialized, so that the hardware ends up in
the correct state even if multiple state machines are changing
simultaneously.
Consolidate all of that into chip/g/rdd.c. The debug command for it
is now 'ccdstate', which just prints the state machines. This will
allow subsequent renaming of the 'ccdopen', etc. commands to 'ccd
open', etc.
Also include UART bit-banging into that state which must be
consistent. Previously, it was possible for bit-banging to leave UART
TX connected, instead of returning it to the previous state.
Use better names for CCD config fields for UART. I'd had them backwards.
BUG=b:62537474
BRANCH=cr50
TEST=manual, with a CR50_DEV=1 image
1) No servo or CCD
Pull SERVO_DETECT low (disconnected)
Pull CCD_MODE_L high (disabled)
Pull EC_DETECT and AP_DETECT high (on)
Reboot. RX is enabled even if cables are disconnected so we buffer.
ccdstate -> UARTAP UARTEC
Pull EC_DETECT low.
ccdstate -> UARTAP
Pull EC_DETECT high and AP_DETECT low.
ccdstate -> UARTEC
Pull AP_DETECT high.
ccdstate -> UARTAP UARTEC
2) Servo only still allows UART RX
Pull SERVO_DETECT high (connected).
ccdstate -> UARTAP UARTEC
3) Both servo and CCD prioritizes servo.
Pull CCD_MODE_L low (enabled).
ccdstate -> UARTAP UARTEC
Reboot, to make sure servo wins at boot time.
ccdstate -> UARTAP UARTEC
Bit-banging doesn't work when servo is connected.
bitbang 2 9600 even -> superseded by servo
bitbang -> disabled
ccdstate -> UARTAP UARTEC
4) CCD only allows more ports and remembers we wanted to bit-bang
Pull SERVO_DETECT low.
ccdstate --> UARTAP+TX UARTEC+BB I2C SPI
bitbang 2 disable
ccdstate --> UARTAP+TX UARTEC+TX I2C SPI
Reboot and see we don't take over servo ports until we're
sure servo isn't present.
ccdstate --> UARTAP UARTEC (for first second)
ccdstate --> UARTAP+TX UARTEC+TX I2C SPI (after that)
5) Bit-banging takes over ECTX
bitbang 2 9600 even
bitbang -> baud rate 9600, parity even
ccdstate -> UARTAP+TX UARTEC+BB I2C SPI
bitbang 2 disable
ccdstate -> UARTAP+TX UARTEC+TX I2C SPI
6) Permissions work. Allow easy access to full console and ccdopen:
ccdset OpenNoTPMWipe always
ccdset OpenNoLongPP always
ccdset GscFullConsole always
Default when locked is full AP UART EC RO, no I2C or SPI
ccdlock
ccdstate -> UARTAP+TX UARTEC
No EC transmit permission means no bit-banging
bitbang 2 9600 even
bitbang -> disabled
ccdstate -> UARTAP+TX UARTEC
But it remembers that we wanted to
ccdopen
ccdstate -> UARTAP+TX UARTEC+BB I2C SPI
bitbang 2 disable
ccdstate -> UARTAP+TX UARTEC+TX I2C SPI
Try turning on/off permissions
ccdset UartGscTxECRx always
ccdlock
ccdstate -> UARTAP+TX UARTEC+TX
No read means no write either
ccdset UartGscRxECTx ifopened
ccdlock
ccdstate -> UARTAP+TX
ccdopen
ccdset UartGscRXAPTx ifopened
ccdlock
ccdstate -> (nothing)
Check AP transmit permissions too
ccdopen
ccdset UartGscRxAPTx always
ccdset UartGscTxAPRx ifopened
ccdlock
ccdstate -> UARTAP
Check I2C
ccdopen
ccdset I2C always
ccdlock
ccdstate -> UARTAP I2C
SPI port is enabled if either EC or AP flash is allowed
ccdopen
ccdset flashap always
ccdlock
ccdstate -> UARTAP I2C SPI
ccdopen
ccdset flashec always
ccdset flashap ifopened
ccdlock
ccdstate -> UARTAP I2C SPI
Back to defaults
ccdoops
Change-Id: I641f7ab2354570812e3fb37b470de32e5bd10db7
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/615928
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
There is no point in updating the Cr50 to an image which will not be
allowed to run due to board ID settings mismatch.
This patch modifies the prototype of check_board_id_mismatch() to
allow to pass to this function an arbitrary pointer to an image
header, so that the function can check not only the image in the flash
memory, but also the image which just arrived over the line.
The contents_allowed() function now checks if the new image is
compatible with the Board ID value in Info1 and rejects the new image
if there is a mismatch.
BRANCH=cr50
BUG=none
TEST=tried updating a Cr50 to an image which is incompatible with the
Info1 fields contents. The update attempt is rejected. Verified
that updating to a compatible image still works as designed.
Change-Id: I3d6c16df11fcabd05888f3cbf5e9a81dc51fe66f
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/650812
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
When checking if the new contents are allowed the updater can reject
the image for different reasons, let's make it possible to pass the
actual rejection reason to the caller of the contents_allowed()
function.
BRANCH=cr50
BUG=none
TEST=verified that attempts to update to an older image are still
being rejected with the proper error code (as generated by
contents_allowed() now).
Change-Id: I24ac7671c4f461ec089f272581723ec2c3a232ff
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/650811
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
In order to prevent keeping the CSAE bit at 1 forever impacts the eSPI
performance, the npcx driver enables host access wakeup functionality
before ec enters deep sleep or wfi. But this bypass also should be added
in __idle() of core/cortex-m/task.c if CONFIG_LOW_POWER_IDLE is
disabled.
This CL also narrows the bypass only when host interface is eSPI.
BRANCH=eve
BUG=b:64730183
TEST=No build errors for make buildall. Disable CONFIG_LOW_POWER_IDLE
functionality on poppy and use following script "count=0; while :;
do echo "--- iteration --- $count"; time flashrom -p ec -r ec.bin; sleep
1; count=$((${count}+1)); done" to test eSPI performances over 300
times. No errors occur and all tests' efficiency are the same as
removing CSAE bypass.
Change-Id: I8b6b69e37318208c185747151c06b3e6bdfd2f4e
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/644967
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Currently, only usb_pd_protocol.c cares about the actual ccd mode
(disabled/partial/enabled). Everything else just cares whether it's
enabled or not. So promote the boolean ccd_is_connected() from
board/cr50 up to chip/g, and rename it to ccd_ext_is_enabled() to
match the new nomenclature (since 'CCD' itself is now too overloaded).
This will make it easier to handle CCD state directly in board/cr50
after we split it from common/case_closed_debug.c
BUG=none
BRANCH=cr50
TEST=make buildall; boot cr50; make sure USB endpoints still work
Change-Id: Ic3df7467bfe29f1c5d7060cac1309a1f0e090d9e
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/648212
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
CCD_CHANGE_HOOK should use CONFIG_CASE_CLOSED_DEBUG_V1.
All boards which use chip/g either use both CONFIG_USB_SERIALNO and
CONFIG_CASE_CLOSED_DEBUG or neither of them, so just depend on
CONFIG_USB_SERIALNO.
This is in preparation for making common/case_closed_debug refer only
to the usb_pd_protocol version (with mode=disabled/partial/enabled),
and cr50 will have its own version (with only enabled/disabled, and
tied more closely to CCD config).
No functionality changes.
BUG=none
BRANCH=cr50
TEST=make buildall -j; boot cr50 and see change hook called
Change-Id: I1985c8c48c1a85fed4549402a7b47b8a9cf135d7
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/648067
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Previously, chip/g/rdd provided a method for an external console
command to override the Rdd cable detect state. But since we'll be
refactoring the 'ccd' command, it's tidier to move this to a console
command inside the rdd driver itself.
BUG=none
BRANCH=cr50
TEST=manual, with no debug cable present
rdd enable -> Rdd connect
rdd -> keepalive
rdd disable
rdd -> connected (hasn't had a chance to run state machine)
(wait <1 sec)
rdd -> debouncing
(wait 1 sec) -> Rdd disconnect
Change-Id: I141eedf8070b4ad2c96cc5a364f4e37dc29bed70
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/647991
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Currently, the console inhibited output when is_readonly=1, and only
inhibited input when is_enabled=0. That's harmless in the current
implementation, because common/case_closed_debug() only ever calls it
with enabled=0/readonly=1 or enabled=1/readonly=0. But if we ever do
decide to use enabled=1/readonly=1, that would have acted like
write-only, not read-only.
Fix that.
BUG=none
BRANCH=cr50
TEST=Attach to cr50 USB console, console is read/write.
Hack USB console to set is_readonly=1, console is read-only.
Change-Id: I04258fe2b040a00f98067d8be48a0632eb16e9c1
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/647336
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Implement keyboard backlight control through HID output report. One
could enable CONFIG_USB_HID_KEYBOARD_BACKLIGHT to enable keyboard
backlight support for a given board. Target board must implement the
`void board_set_backlight(int brightness)` function in order correctly
set backlight.
BRANCH=none
BUG=b:37971411,b:63364143
TEST=with follow up CLs
1. `make BOARD=hammer -j`
2. `echo 10 > /sys/class/leds/hammer\:\:kbd_backlight/brightness`
console shows 'Keyboard backlight set to 10%'
Change-Id: Ibeff510a0d996ddebf61b54ed6b500b02c35564a
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://chromium-review.googlesource.com/586348
Commit-Ready: Wei-Ning Huang <wnhuang@chromium.org>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
-Routing HPET1 timer requires HPET's General Config register's Legacy
routing bit should be set.
-For HPET0 interrupt, no need to set IRQ# to T0C register.
-change IRQ# back to default values.
BUG=None
BRANCH=master
TEST=`Build ISH and verify the timer interrupt via various
console cmds`
Change-Id: I9f83d62a1f7d999ebf6cedafd38691531ec91081
Signed-off-by: Kyoung Kim <kyoung.il.kim@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/627628
Commit-Ready: Kyoung Il Kim <kyoung.il.kim@intel.com>
Tested-by: Kyoung Il Kim <kyoung.il.kim@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a function to translate device_state enum into a string, then use
it for printing the ec and RDD state.
Refactor ec_state so that all state transitions go through a
set_state() function, which makes it easier to turn on debugging all
state transitions. That's normally not compiled in because it would
be spammy during debouncing.
BUG=none
BRANCH=cr50
TEST=ccd command prints EC and RDD states
Change-Id: Ie7bc56c7b66beee23d1d1989711c640e5e39ce43
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/642121
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
On some boards, it was seen that SuzyQable wasn't detected by the rdd
block. The voltage around 0.4V is marginal with a Vbus around 4.75V.
This commit simply adjust the 0.4V comparator reference voltage to 0.3V
in order to make the detection work.
BUG=b:64847312
BRANCH=cr50
TEST=Find a soraka where SuzyQable didn't work. Verify with this patch,
it does work. Additionally, verify that servo_v4 continues works.
Change-Id: If54630ec469408031cd84ffb93ef5fea42bdee3b
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/633403
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Currently, chip/g uses jtag_pre_init() to do some chip
pre-initialization that isn't actually related to JTAG. This has been
harmless, but it's currently the only chip which actually does "JTAG"
pre-init, and we'd like to get rid of that. So, move that
functionality to a new optional chip_pre_init() function.
BUG=chromium:747629
BRANCH=cr50
TEST=make buildall
boot cr50
make all dis; confirm chip_pre_init() is called early in <main>
Change-Id: I3cae0747ab0c3cc974fce9f108947207b38e035f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/629876
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The bit controlling the tri-state of FIU pins is reserved when the
internal flash is used and should not be modified. This CL adds a
compiler error to prevent this kind of misuse.
BRANCH=none
BUG=none
TEST=No build errors for "make buildall". "BORAD=npcx7_evb make" with
CONFIG_CMD_FLASH_TRISTATE defined, make sure the error message is
printed.
Change-Id: I020c8ab9e02b9a377879bbd2a337943e77a369d6
Signed-off-by: CHLin <CHLIN56@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/624828
Commit-Ready: CH Lin <chlin56@nuvoton.com>
Tested-by: CH Lin <chlin56@nuvoton.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
We want to be able to collect statistics of the i2c bus problems. This
patch logs an event each time the wedged bus recovery happens.
BRANCH=cr50
BUG=b:63760920
TEST=with the upcoming patches verified that i2c recovery events are
logged as expected.
Change-Id: I1241b2dece33f89cd724d53a48f94e17f4415c62
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/620114
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
It turns out SCLH = 0x5 is still a little fast (411 kHz on hammer),
let's update it to 0x6.
See 5e6f9a2b38 "chip/stm32/i2c-stm32f0: Adjust 400kHz setting (48Mhz clock source)"
for details.
BRANCH=none
BUG=b:36172041
TEST=Measure I2C speed to be <400 kHz on hammer
Change-Id: I2b5acc532963c407144b8e2a7786d3e2302192d3
Reviewed-on: https://chromium-review.googlesource.com/625507
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Toshak Singhal <toshak@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In boot protocol mode, we must only send the first 8 bytes of the
report. Also, go back to report mode on USB reset.
When mode is changed, we immediately toggle keyboard endpoint,
to make sure the appropriately sized packet is sent (otherwise,
a longer packet packet will be sent once, which confuses AP
firmware).
BRANCH=none
BUG=b:62004286
BUG=b:64953295
TEST=Flash hammer, check that keyboard works at firmware screen
and in the OS, and that new key works in OS.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Change-Id: If7d6aa6c2dd127b9de34fc93d06bc0dd6e6128a2
Reviewed-on: https://chromium-review.googlesource.com/627344
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
In eSPI systems, when the host performs a data read from the Shared
Memory space, the returned data may be corrupted. This is a result of
the Core-to-Host access enable bit being toggled (by toggling CSAE bit
in SIBCTRL register) during an eSPI transaction. The bypass for this
symptom is to set CSAE bit to 1 during initialization and remove the
toggling of CSAE bit from other EC firmware code.
But keeping the CSAE bit at 1 forever also impacts the eSPI performance
a lots. When the core clock is stalled by sleep, deep sleep or wfi
instruction, the eSPI Peripheral Channel transaction is stalled if this
bit is set. The bypass for this symptom is to wake up the core by eSPI
peripheral channel transaction and let eSPI module handle the remaining
packet.
BRANCH=eve
BUG=b:64730183
TEST=No build errors for make buildall. Flash poppy ec image, make sure
it can boot to OS. Run "ectool version" over 100000 times, no error
occurs. Use following script "count=0; while :; do echo "---
iteration --- $count"; time flashrom -p ec -r ec.bin; sleep 5;
count=$((${count}+1)); done" to test eSPI performances over 1000
times. No errors occur and all tests' efficiency are the same as
removing CSAE bypass.
Change-Id: I1b9051c5a3d368a5917882d9d1c3bb00481a53ad
Signed-off-by: CHLin <CHLIN56@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/620301
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
The STM32F76x is really close to the STM32F4 family, so the most concise
implementation is just using CHIP_FAMILY_STM32F4 and adding
CHIP_VARIANT_F76X.
Tune the clock settings to 180 Mhz CPU clock as the goal is performance.
(over-drive is not implemented yet to get to 216 Mhz)
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=ran on nucleo-f767zi board.
'make BOARD=nucleo-f767 flash', the red LED is on and the green LED
turns on/off when pressing the user button, UART console works properly.
Change-Id: I1f67df3aec874c965c81188df46c72de210728d9
Reviewed-on: https://chromium-review.googlesource.com/612750
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
A common failure condition on the i2c bus is when the master
unexpectedly stops clocking the bus while the slave is driving the SDA
line low. In this case the master is not able to issue Stop or Start
sequences, which makes the bus unusable.
Good slave controllers are able to detect this condition and recover
from it by removing the pull down from the SDA line. This patch adds
this capability to the g chip i2c slave controller.
A new timer function is created which samples the SDA line twice a
second. If it detects that SDA is low in two consecutive invocations
and the number of i2cs read interrupts has not advanced, it decides
that the "hosed slave" condition is happening and reinitializes the
i2c driver, which removes the hold from the SDA line.
Even though the state of the SDA line is supposed to be accessible
through the I2CS_READVAL register, it in fact is not, reads always
return zero in the SDA bit. To work around this a GPIO (port 0, bit
14) is being allocated to allow to monitor the state of the line, it
is multiplexed to the same pin the SDA line uses.
When the AP is in low power modes the SDA line is held low, this state
should not trigger i2c reinitializations.
CQ-DEPEND=CL:616300
BRANCH=none
BUG=b:35648537
TEST=connected H1 on the test board to an I2c master capable of
stopping clocking mid byte. Observed that the existing code would
just sit in the "hosed" state indefinitely. The code with the fix
recovers from the condition (drives the SDA line high) 500ms to
1s after the failure condition is created.
Change-Id: Iafc7433bbae9e49975a72ef032a923274f8aab3b
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/614391
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Add a delay to allow the clocks and usb signals to settle.
BUG=b:63767046,b:63867566
BRANCH=cr50
TEST=put the eve ec into hibernate, wait until cr50 enters deep sleep,
use the uart to wake it up, and verify that it eventually reenters deep
sleep
Change-Id: I26463ce3e00996368a791a245b0f9de01737478c
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/598448
Reviewed-by: Marius Schilder <mschilder@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
In npcx7, we introduce an enhanced version of Serial Host Interface
(SHI) module. This CL adds the support for it.
It includes:
1. Increase the size of IBF/OBF from 64 bytes to 128 bytes.
2. Add IBULVL/IBFLVL2 in SHICFG4/SHICFG5 which can configure at which
level the IBF pointer reaches to trigger an interrupt to core.
The current setting of these two register fields are:
IBFLVL - 64 (half full)
IBFLVL2 - 8 (the size of host command protocol V3 header)
3. Dedicated CS high/low interrupts.
In old SHI module, the way to generate CS high interrupt event is via
EOR bit. However, it has a defect that EOR won't be set to 1 when CS
is de-asserted if there is no SHI CLK generated. It makes the
handling of glitch condition more complicated.
In the new SHI module, we introduce the CS high/low interrupts
(by enabling the CSnFEN/CSnREEN) to make it easier to handle the
glitch.
The new SHI module is enabled during SHI initialization when the chip
family is npcx7.
BRANCH=none
BUG=none
TEST=No build errors for "make buildall". Test host command
communication is ok between npcx7 EVB and a host emulator.
Make sure the glitch condition can be detected and handled.
Also test the driver on gru, make sure it won't break the operation of
old SHI module.
Change-Id: If297fd32a0ec2c9e340c60c8f1942868fa978fbc
Signed-off-by: CHLin <CHLIN56@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/607812
Commit-Ready: CH Lin <chlin56@nuvoton.com>
Tested-by: CH Lin <chlin56@nuvoton.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
We previously disabled the USB PHY to the AP. But the BOARD_AP_USB
property lingered on. Remove the property.
Also clean up the idle task deciding when to do utmi wakes. With the
AP USB connection disabled, that's only necessary when the debug cable
is attached, so we can check that explicitly.
BUG=none
BRANCH=cr50
TEST=make buildall; boot CR50_DEV=1 image
Change-Id: If81a7bcfe845d9d70dcc7e16239244a4f5f2427b
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/616301
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
This reverts commit ddbfe690e2.
Reason for revert: Causes move cursor movements to be choppy, and device
to be very unresponsive during flashrom EC operations.
Original change's description:
> npcx: workaround the bug that SHM data read via eSPI may be corrupted
>
> In eSPI systems, when the Host performs a data read from the Shared
> Memory space, the returned data may be corrupted. This is a result of
> the Core-to-Host access enable bit being toggled (by toggling CSAE bit
> in SIBCTRL register) during an eSPI transaction.
>
> The workaround in this CL is to set CSAE bit to 1 during initialization
> and remove the toggling of CSAE bit from other EC firmware code.
> (i.e., let the CSAE bit be always 1.)
>
> BRANCH=none
> BUG=none
> TEST=No build errors for make buildall. Flash poppy ec image, make sure
> it can boot to OS. Run "ectool version" over 100000 times, no error
> occurs.
>
> Change-Id: I7aac6805ece64e8f77964d4acb026d9871cd2ebe
> Signed-off-by: CHLin <CHLIN56@nuvoton.com>
> Reviewed-on: https://chromium-review.googlesource.com/590396
> Commit-Ready: Shawn N <shawnn@chromium.org>
> Tested-by: CH Lin <chlin56@nuvoton.com>
> Reviewed-by: Shawn N <shawnn@chromium.org>
BUG=b:64730183
TEST=flashrom -p ec -r ecr.bin, device still responsive.
Change-Id: Idaeef2707df990b2441a77a15807698d41018449
Reviewed-on: https://chromium-review.googlesource.com/618366
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
