We only used I2C_PORTS_USED to iterate through the list of hardware ports
actually in use, but we defined it in board.h at the same place where we
matched particular I2C devices to the (possibly shared) buses they're on.
This CL makes I2C_PORTS_USED into a global constant, so it can be set
automatically where we initialize the ports, and doesn't have to be
related to the list of attached devices.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=manual
Build everything, run all tests, should still work.
Change-Id: I65f22f5cadfc4b3afe51af48faa5fb369bc3aa09
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/171884
include/config.h should have the canonical list of all CONFIG_* macros used
everywhere else. This fixes some that weren't included, and some that had
been changed in one place but not in others.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=manual
Build everything. It should still work.
cd src/plaform/ec
make runtests
for i in bds bolt daisy discovery falco kirby link mccroskey peppy pit puppy rambi samus slippy snow spring; do make BOARD=$i || touch died.$i; done
There shouldn't be any died.* files.
Change-Id: I0a1ec2d57668509c514dc5a521e547836a3e9894
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/171690
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Every board other than link does the same thing - filter out the power
button event, then set the WAKE_L gpio level based on the remaining
events. This code doesn't need to be duplicated 7 times, so make it common.
Link didn't filter out the power button wake signal, but works fine
with the common implementation. Like the other boards it gets a power
button wake event via the dedicated PCH PWRBTN# signal.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=suspend link, then wake using power button press
compile all platforms; pass unit tests
Change-Id: Ib3a6d310d0f5e337374b3c331ab2872fe377bdf6
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/171405
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This was previously done in a board-specific function across 4 boards.
Except that the board-specific function was identical in all cases
(that is, not really board-specific). Put it back in the common
implementation to get rid of duplicated code, and use
CONFIG_TEMP_SENSOR_POWER_GPIO to indicate which GPIO rail controls the
sensor power.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards; pass unit tests
Change-Id: I29de40001d5d4dc873e5ba8f3abb328c6271f235
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/171140
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
The old backlight_x86 code did
(backlight enable) = (lid is open) && (GPIO request from AP)
Newer systems will AND those signals in hardware. Support those
systems by separating CONFIG_BACKLIGHT_LID and
CONFIG_BACKLIGHT_REQ_GPIO, and add tests for the case where the enable
signal is dependent only on the lid position.
BUG=chrome-os-partner:22960
BRANCH=none
TEST=pass unit tests
Change-Id: I1909426e49f00a8acd5047fd88c801cba1dacd76
Reviewed-on: https://chromium-review.googlesource.com/170925
Tested-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Commit-Queue: Randall Spangler <rspangler@chromium.org>
This provides an interface to detach and re-attach fake I2C devices,
which can be used to test I2C connection failure.
BUG=chrome-os-partner:19235
TEST=Pass sbs_charging test along with the next CL
BRANCH=None
Change-Id: Ibfee79b13d45e62377d894aa28547e77bef2189e
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170752
Reviewed-by: Randall Spangler <rspangler@chromium.org>
For testing, we are now mocking things at function-level instead of
file-level. No need to have separate header file for smart battery
functions now. Merge them back to smart_battery.h.
Just moving code. No functional change.
BUG=chrome-os-partner:18343
TEST=util/make_all.sh
BRANCH=None
Change-Id: I4de1f73def447e75458118c1148c598794ddc091
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170751
Reviewed-by: Randall Spangler <rspangler@chromium.org>
With the PWM interface refactoring, only the CPU fan uses the fan.h
interface. All other PWM channels (keyboard backlight, etc.) use the
pwm.h interface. Remove the unused constants, and rename FAN_CH_CPU
to CONFIG_FAN_CH_CPU so it fits with the other fan config options.
No functional changes; just renaming things.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all targets; pass unit tests
Change-Id: I391fbeaf54afcc29a11c2799a4520b7ad8784796
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170534
Reviewed-by: Vic Yang <victoryang@chromium.org>
This should have all the correct GPIO mappings.
Chipset and charger tasks are currently disabled, until we bring up
the voltage rails and I2C communication.
BUG=chrome-os-partner:22895
BRANCH=none
TEST=compiles; everything else needs to wait until we get hardware
Change-Id: Iea49fe7ab8bd17f61c8cc6c71f236a503418ee28
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170540
Reviewed-by: Vic Yang <victoryang@chromium.org>
switch.c currently assumes that all boards have GPIO_RECOVERY_L. This
is not true for Rambi, and also isn't true for ARM boards (which
should also eventually use the common switch implementation).
Add a new CONFIG_SWITCH_DEDICATED_RECOVERY option to control whether
to compile this support.
BUG=chrome-os-partner:22893
BRANCH=none
TEST=compile all boards; pass unit tests
Change-Id: If6f34d1afd580c9d79a8edcdda18833068e70f66
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170489
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
We've removed a few constants from the exported header file since the last
big sync. Just in case some of them are still in use (coredump, flashrom),
let's make it easy to redistribute the header unchanged. We can remove them
for real next time.
BUG=chromium:251441
BRANCH=none
TEST=manual
Compile, test, run, etc. This CL just adds back some unused (by the EC)
constants that were previously removed, so nothing should change.
Change-Id: Ia9889db89a90d56c8154fea1e8c8a483fdcae805
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170522
Reviewed-by: Randall Spangler <rspangler@chromium.org>
For bringup, we need to be able to compile a binary with the chipset
task disabled. Chipset functions should be stubbed to do nothing in
that case.
BUG=chrome-os-partner:22820
BRANCH=none
TEST=compile falco, pit, link with chipset task commented out in ec.tasklist
Change-Id: I73a4e09effb049f19b1a128e643b267d6469037b
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170221
The battery files contain board-specific constants and a few small
methods like battery-detect and battery-cut. Most of these aren't
reused across platforms. The battery files have also been cleaned up
so those board-specific constants basically all that's left in them.
Where a file is used by a single board only, move it to
board/(boardname)/battery.c. Batteries used by more than one board
(e.g. battery_link.c used by both link and bolt) are still in
common/battery_*.c, since that's cleaner than duplicating the file in
each board's directory.
No code changes, just moving files.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards and pass unit tests
Change-Id: I946c8eb874672c77f9b77105e5b900f98fa48d0f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169893
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
To test drivers, we need a way to fake I2C periphrals. With this CL, a
fake peripheral can be done by declaring its own I2C read/write
functions. The fake I2C peripherals may return EC_ERROR_INVAL to
indicate it's not responding. The emulator I2C read/write call scans
through all registered I2C peripherals and uses the first response.
BUG=chrome-os-partner:19235
TEST=Pass sbs_charging test with the next CL.
BRANCH=None
Change-Id: I9380dc40e147781b42e09eb6979c864bbd9f2ac4
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169511
Reviewed-by: Randall Spangler <rspangler@chromium.org>
STM32 has a single-byte mailbox for UART I/O. When the core clock
runs at 16Mhz we can service interrupts fast enough to handle 115200
baud input, but when we drop to 1MHz we drop characters. Using DMA to
receive input solves this problem.
The STM32 DMA engine can only generate interrupts when the transfer is
half-done / all-done, so we need to poll the DMA receive-head-pointer
to see if individual characters have been received. Do this in the
tick task (every 250ms). When a character is received, poll more
quickly for a bit (5 times before the next tick) so the input console
is more responsive to typing.
BUG=chrome-os-partner:20485
BRANCH=none
TEST=Console is responsive to debug commands. For example, help -> prints help
apshutdown -> shuts down AP
arrow keys -> move cursor and scroll through command history
Ctrl+Q, help, wait a second, Ctrl+S -> help output printed after Ctrl+S
Then in chip/stm32/config_chip.h, comment out #define CONFIG_UART_RX_DMA
and rebuild/reflash the EC. When the AP is up, the console works normally
but after 'apshutdown', the EC drops to 1MHz core clock, and the arrow
keys don't work. (This step confirms that adding DMA support did not
change the behavior of systems where CONFIG_UART_RX_DMA is not defined.)
Change-Id: I199448354824bd747c7b290ea7fd5ccf354c11bb
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169406
Reviewed-by: Simon Glass <sjg@chromium.org>
If CONFIG_HOOK_DEBUG is defined, the maximum run time of each hook is
recorded. Also, record the delayed amount of time of HOOK_TICK and
HOOK_SECOND firing. The statistics are available through console command
'hookstats'.
Also fix a bug that CC_HOOK is used but not defined when
CONFIG_HOOK_DEBUG is defined.
BUG=chrome-os-partner:21801
TEST=Build with HOOK_DEBUG and check 'hookstats'
BRANCH=None
Change-Id: I3acba3abdd487cf20d9a532429f766cdddea2e93
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169274
All calls to it did
if (uart_tx_stopped())
uart_tx_start();
And that was the only use of uart_tx_stopped(). Merge the functions.
BUG=chrome-os-partner:20485
BRANCH=none
TEST=EC debug console still prints output and accepts commands.
Ctrl+Q pauses output and Ctrl+S resumes it.
Change-Id: I113c64f5fdfc6b02b63034a74b1a3c6c6a76c351
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169329
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Nothing ever called uart_flush_input() or uart_gets(), so remove them.
They're dead code, and make implementing UART DMA input more complex.
BUG=chrome-os-partner:20485
BRANCH=none
TEST=build all platforms; pass unit tests
Change-Id: I94c2c372ac3f326b98e819b2c89b8995311b2868
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169345
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Having a per-device enum list for use by the EC_CMD_GET_SET_VALUE command
won't work when the one-and-only ectool tries to talk to different devices.
Any particular enum may be missing or have a completely different meaning.
Instead, we can do the same thing that EC_CMD_HOST_EVENT_* does - use the
same structs for a bunch of different commands.
If/when we run out of command numbers (it's currently only 8 bits), we'll
just switch to using EC protocol v3 (see crosbug.com/p/20820), which
provides 16 bits for the command.
This CL renames EC_CMD_GET_SET_VALUE to EC_CMD_GSV_PAUSE_IN_S5 (since that's
the one-and-only use of it at present), and renames the params/response
structs as well. Since only the names are changing, the implementation
remains backwards-compatible (assuming the flags value usage is preserved by
ectool for the EC_CMD_GSV_PAUSE_IN_S5 command, which it is).
If I can cherry-pick this change into the one place where it's being used, I
will.
BUG=chromium:287969
BRANCH=ToT
TEST=manual
Although this is primarily an internal name change, it also means that the
commands to invoke the previous usage of this feature have changed. To test:
On Haswell systems only.
To enable the pause in S5 at shutdown, do either of these:
EC console: pause_in_s5 on
root shell: ectool pause_in_s5 on
Shut the AP down politely, and it should pause in S5 for 10 seconds before
continuing to G3. You can see this by watching the EC console.
To disable the pause in S5 at shutdown, do any of these:
EC console: pause_in_s5 off
root shell: ectool pause_in_s5 off
or
press Refresh + POWER
Boot the system, then politely shut down. This time it should go directly to
G3 without pausing in S5.
Change-Id: Ic614fed37ad89db794c2bbcca2b83d1603030ab2
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168816
This reduces the number of UART interrupts by a factor of 12, and
reduces the overall interrupt rate on STM32 by a factor of 2.
BUG=chrome-os-partner:20485
BRANCH=none (not required for pit branch)
TEST=Boot pit. Ctrl+Q pauses debug output; Ctrl+S resumes it.
'crash divzero' still prints a full crash dump.
And util/makeall.sh passes builds all platforms and passes tests.
Change-Id: I86993e14b436150298dcb2c6d29086cc3c9db418
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168814
This is a precursor to DMA-based UART transfers, which require
different processing for DMA vs PIO output types.
BUG=chrome-os-partner:20485
BRANCH=pit
TEST=Boot pit; verify EC console still works.
Change-Id: I6d6f55561eeebe9bd2928b2bfb25278c86f689d1
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168811
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
The definition of GPIO interface allows passing in multi-bit mask, and
this is what's done by gpio_config_module(). Fix STM32L's function so
that it doesn't accidentally set incorrect GPIO register values.
BUG=chrome-os-partner:22605
TEST=On Kirby, do 'led r 0' and check the value of 0x40020800 is
0x01540000.
BRANCH=None
Change-Id: I9a1c8074aab7345485a590ecf138bf99d0742997
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168739
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Randall Spangler <rspangler@chromium.org>
Depending on the system, the AP can be throttled in at least two different
ways - politely, where it's just asked to slow down a bit, and forcefully
using a hardware signal (like PROCHOT). In addition, the request for
throttling can come from multiple tasks.
This CL provides a single interface, specifying both the type of throttling
desired and the source of the throttling request.
For each type, any source can can start throttling, but all sources must
agree before it stops. The changes are protected by a mutex, so that
requests from multiple tasks don't interfere with each other.
BUG=chrome-os-partner:20739,chromium:287985,chromium:287983
BRANCH=ToT
TEST=manual
Build-time test:
cd src/platform/ec
make BOARD=falco runtests
Run-time test: Lower the temp thresholds, turn the fan off, and watch the
throttling turn off and on as things heat up. For example, on the EC
console:
> temps
PECI : 339 K = 66 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
> thermalset 0 341 343
sensor warn high halt fan_off fan_max name
0 341 343 383 333 363 PECI
1 0 0 0 0 0 ECInternal
2 0 0 0 0 0 G781Internal
3 0 0 0 0 0 G781External
>
> temps
PECI : 339 K = 66 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
>
> fanduty 0
Setting fan duty cycle to 0%
>
> apthrottle
AP throttling type 0 is off (0x00000000)
AP throttling type 1 is off (0x00000000)
>
[430.152000 thermal WARN]
[430.152233 event set 0x00020000]
[430.152497 event clear 0x00020000]
[430.152714 ACPI query = 18]
[430.152444 sci 0x00020000]
[430.153051 set AP throttling type 0 to on (0x00000001)]
> gpioget CPU_PROCHOT
0 CPU_PROCHOT
>
[436.153742 thermal HIGH]
[436.153979 set AP throttling type 1 to on (0x00000001)]
> gpioget CPU_PROCHOT
1* CPU_PROCHOT
> [441.155319 thermal no longer high]
[441.155587 set AP throttling type 1 to off (0x00000000)]
[442.155604 thermal HIGH]
[442.155841 set AP throttling type 1 to on (0x00000001)]
[446.156623 thermal no longer high]
[446.156890 set AP throttling type 1 to off (0x00000000)]
temps
PECI : 343 K = 70 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
>
[447.156827 thermal HIGH]
[447.157064 set AP throttling type 1 to on (0x00000001)]
apthrottle
AP throttling type 0 is on (0x00000001)
AP throttling type 1 is on (0x00000001)
> gpioget CPU_PROCHOT
1 CPU_PROCHOT
>
Now turn the fan back on:
> fanauto
>
[456.159306 thermal no longer high]
[456.159574 set AP throttling type 1 to off (0x00000000)]
> apthrottle
AP throttling type 0 is on (0x00000001)
AP throttling type 1 is off (0x00000000)
> temps
PECI : 341 K = 68 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
>
[473.163905 thermal no longer warn]
[473.164168 event set 0x00040000]
[473.164453 event clear 0x00040000]
[473.164670 ACPI query = 19]
[473.164379 sci 0x00040000]
[473.164987 set AP throttling type 0 to off (0x00000000)]
temps
PECI : 340 K = 67 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
>
> apthrottle
AP throttling type 0 is off (0x00000000)
AP throttling type 1 is off (0x00000000)
>
Change-Id: I9ee1491a637d7766395c71e57483fbd9177ea554
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168802
This is in preparation for enabling DMA-based UART transfers, to
improve UART performance on STM32.
BUG=chrome-os-partner:20485
BRANCH=none
TEST=Boot pit. Host commands should still be received; this verifies DMA
is still operational.
Change-Id: Ibc3b2e2cd187547eb61b85e4a086704accd7f2fb
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168810
At normal AP shutdown, Haswell systems skip S5 entirely and go directly to
G3. It's sometimes handy to pause in S5 as the other systems do, for things
like power-cycle tests that use the RTC to do a delayed wake from S5.
This CL adds a console command and a host command to enable/disable that
pause in S5.
The default is to skip S5, and the override value is not persistent across
EC reboots, so whenever the EC hibernates or reboots (Refresh + Power, software
sync), you'll have to re-enable it again.
BUG=chrome-os-partner:22346
BRANCH=falco,ToT
TEST=manual
On Haswell systems only.
To enable the pause in S5 at shutdown, do either of these:
EC console: gsv s5 1
root shell: ectool pause_in_s5 on
Shut the AP down politely, and it should pause in S5 for 10 seconds before
continuing to G3. You can see this by watching the EC console.
To disable the pause in S5 at shutdown, do any of these:
EC console: gsv s5 0
root shell: ectool pause_in_s5 off
or
press Refresh + POWER
Boot the system, then politely shut down. This time it should go directly to
G3 without pausing in S5.
Change-Id: I324e6e2373bc20b61a731b4ef443d7bb8edb6b83
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168086
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This checks boot key combination like Power-F3-ESC and Power-F3-Down can
be properly detected.
BUG=chrome-os-partner:19236
TEST=Pass kb_scan test
BRANCH=None
Change-Id: I180918977299219a8421798dac2ab9fed84ef9a2
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167802
We already have a multi-step test. Let's move it to test_util.c so that
upcoming tests can also use it.
BUG=chrome-os-partner:19235
TEST=Pass all tests
BRANCH=None
Change-Id: I6b7a036297f3b4b2778687488d1dc5b5bb4fe255
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167950
Currently only x86 platform uses charge_state.c, and it's been tailored
to fit smart battery and bq247xx charger family.
For Kirby, we have different types of battery and charger, and thus need
to make some change to accommodate them. This includes:
- Abstract out smart battery specific bit mask
- Implement missing functions required by GAIA chipset module
- Add config flags for charging-enabled GPIO pin
- Allow battery that doesn't report desired voltage and current
BUG=chrome-os-partner:22055
TEST=Build all boards
TEST=Boot Link and check it charges/discharges battery
TEST=Test charging/discharging on Kirby along with the next two CLs
BRANCH=None
Change-Id: I910c030a45b4f775afffec0127cdc31e89b9dd55
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168005
This is only for initial bringup that requires OTG to boot kernel. Note
that we are expecting firmware for USB ID detection and hardware change
to charger chip, so this is likely going to be thrown away.
BUG=chrome-os-partner:21964
TEST=Plug in OTG dongle and check VBUS voltage is ~5V
TEST=Unplug and check it's ~0V.
BRANCH=None
Change-Id: Iee66bef117188fea14a76459945be3bf5afef0dd
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167832
BQ27541 is not a smart battery IC, and thus we cannot use existing smart
battery driver. Let's add a driver that implements a smart-battery-like
interface.
The 'battery' console command is also moved to battery.c so that it can
be reused by different battery driver.
BUG=chrome-os-partner:22048
TEST=Type 'battery' and check the reported values are sane.
TEST=Check 'battery' command works fine on Spring.
BRANCH=None
Change-Id: I5d1eaeb3f801478f3b9473fd43c1f2a2eda75859
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/66340
This adds EC_CMD_GET_SET_VALUE to the list of host commands. We have a bunch
of single-value getter/setter commands, which is wasteful. This is a start
towards unifying them into a simpler command.
BUG=chromium:285358
BRANCH=ToT,falco
TEST=none
There's nothing to test just yet. This just adds the command and some basic
interfaces. A future commit will make use of it.
Change-Id: Iee986b9d273b422bb06f3a0c9b7af50617f03d7f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168083
Reviewed-by: Randall Spangler <rspangler@chromium.org>
ADC module on STM32L is clocked by HSI oscillator, and thus we need to
switch to HSI if using MSI. After the conversion, if the system is not
in S0, clock is switched back to MSI again.
There are several register bits that can only be written when ADC is
powered down. For now, let's just power down the ADC after each
conversion.
Currently ADC watchdog is not working and is disabled on STM32L.
BUG=chrome-os-partner:22242
TEST=Try multiple all-channel and single-channel reads in S0 and S5.
BRANCH=None
Change-Id: I769dda8a9c69ac9de1eb22d6d259034eef8c1ac4
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167454
If we reboots the emulator without flushing test coverage information,
the test coverage report will be incorrect. Let's fix this by flushing
it before every reboot.
BUG=chrome-os-partner:19235
TEST=Generate test coverage report and check correctness.
BRANCH=None
Change-Id: I1eb060e419b767f382325bed841366c491ba56b7
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167770
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
GPIO_INPUT is defined as 0, and any GPIO flag cannot be examined against
GPIO_INPUT. Change GPIO_INPUT to non-zero value to avoid this.
BUG=chrome-os-partner:22275
TEST=On Kirby, set a GPIO to output and pull it low, and then set it back to
input. Check it can be pull high externally.
TEST=Build all boards.
TEST=Boot link and spring.
BRANCH=None (unless this bug hits some other boards.)
Change-Id: I84b9936c24af538ac59c36129fda27ca879bf9d1
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167190
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Most systems don't have a lightbar. Those that do need a way to detect that
one exists. That's easily done by just sending a EC_CMD_LIGHTBAR_CMD command
to the EC and checking the result. If the response is
EC_RES_INVALID_COMMAND, there isn't a lightbar.
But what .cmd value should we use in struct ec_params_lightbar? Future
lightbar implementations (if any), could remove existing functions or add
new ones, so there isn't a safe choice.
This change adds a LIGHTBAR_CMD_VERSION operation to determine if any new
implementation exists. Future systems should return some useful information
in response to this command. Existing systems will return
EC_RES_INVALID_PARAM, which is enough to distinguish them.
BUG=chromium:239205
BRANCH=none
TEST=manual
make BOARD=link
make BOARD=link runtests
There are no user-visible changes in functionality to anything.
Change-Id: Ibe37f74a4dcbf68dd6bfd1963530aec907e67534
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167549
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Instead of checking for BOARD_<board> to determine whether the board has
control over a power rail or not, use config option for this. Boards
without control over some power rails can then undefine the option in
board.h.
BUG=chrome-os-partner:21964
TEST=Build all boards.
BRANCH=None
Change-Id: I7ee4ebdb3ea595e182845e40db165623ee271997
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167200
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This is the initial version of BQ24192 charger driver. For now, it only
probes for BQ24192 chip on initialization and get BQ24192 into host
mode.
Also, charger_closest_current() is identical across all charger drivers.
Let's move it to charger_common.c.
BUG=chrome-os-partner:22238
TEST=Build all boards. Boot Kirby and see BQ24192 initialized.
BRANCH=None
Change-Id: I5291362ff0e69b281bffd6d609ce6dc48eb10898
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167457
Before this change drivers had no way of knowing that a frequency
change was coming. This could cause problems for some drivers (like
i2c) that need to make sure that a transaction isn't happening while a
frequency change is happening.
The PRE_FREQ_CHANGE archiecture is very simple here and we don't allow
any way to cancel it.
At the moment, we guarantee:
- We won't call PRE_FREQ_CHANGE with interrupts disabled, so acquiring
locks / sleeping is OK.
- We'll call the actual HOOK_FREQ_CHANGE after the PRE_FREQ_CHANGE.
PRE_FREQ_CHANGE and HOOK_FREQ_CHANGE should not use deferred function
calls.
BRANCH=pit
BUG=chrome-os-partner:22093
TEST=With all patches together:
- on AP: suspend_stress_test
- on EC: battery 10000 50
Change-Id: I2731a3e85d41e749fa571fdb74b5c9b12043cda6
Signed-off-by: Doug Anderson <dianders@chromium.org>
Previous-Reviewed-on: https://chromium-review.googlesource.com/167101
(cherry picked from commit d84c0dbbf7c5a72917a820e292ecfdfa698d0fb9)
Reviewed-on: https://chromium-review.googlesource.com/167148
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The ID detection and charging circuits on Spring are very different from
that on Kirby. PWM current limit is no longer used. The ID detection
sequence is also different. Also, there is no boost circuit on Kirby.
Given those hardware issues that we had to work around on Spring, it's
unlikely that we will have another board that shares the same/similar
ID detection design with Spring. Let's rename extpower_usb to
extpower_spring to better reflect this.
BUG=None
TEST=Build and boot Spring.
BRANCH=None
Change-Id: I7c212a121eed55665593cb7e1b2b672891819940
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/67031
This unifies the PWM module interface for LM4 and STM32. Now PWM
channels are defined in board.h/board.c. Instead of calling functions
named pwm_set_fan_duty(x), one can now use pwm_set_duty(PWM_CH_FAN, x),
which prevents additional functions added when we have a new PWM
channel.
BUG=chrome-os-partner:18343
TEST=Limit input current on Spring.
TEST=Check power LED in S0/S3/S5 on Snow.
TEST=Check keyboard backlight functionality on Link.
TEST=Check fan speed control/detecting on Link.
BRANCH=None
Change-Id: Ibac4d79f72e65c94776d503558a7592f7db859dc
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/64450
Reviewed-by: Randall Spangler <rspangler@chromium.org>
I missed this requirement the first time. Now it's here. Also adding a test
for it as well.
BUG=chrome-os-partner:20739
BRANCH=falco
TEST=manual
make BOARD=falco runtests
Change-Id: I88aac8d12d09f7970b04c4aa02b6986b5ea16306
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66684
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Problems with existing thermal control loop:
* Not multi-board friendly. thermal.c only supports Link and needs
refactoring. Temp thresholds and fan speeds are hard-coded.
* Only the PECI temp is used to determine the fan speed. Other temp sensors
are ignored.
* Has confusing data structures. Values in the CPU temp thresholds array mix
ACPI thresholds with fan step values.
With this change, the thermal task monitors all temp sensors in order to
perform two completely independent functions:
Function one: Determine if the host needs to be throttled by or informed of
any thermal events.
For thermal events, each temp sensor will have three threshold levels.
TEMP_HOST_WARN
* When any sensor goes above this level, host_throttle_cpu(1) will be called
to ask the CPU to slow itself down.
* When all sensors drop below this level, host_throttle_cpu(0) will be called.
* Exactly AT this level, nothing happens (this provides hysteresis).
TEMP_HOST_HIGH
* When any sensor goes above this level, chipset_throttle_cpu(1) will be
called to slow the CPU down whether it wants to or not.
* When all sensors drop below this level, chipset_throttle_cpu(0) will be
called.
* Exactly AT this level, nothing happens (this provides hysteresis).
TEMP_HOST_SHUTDOWN
* When any sensor is above this level, chipset_force_shutdown() will be
called to halt the CPU.
* Nothing turns the CPU back on again - the user just has to wait for things
to cool off. Pressing the power button too soon will just trigger shutdown
again as soon as the EC can read the host temp.
Function two: Determine the amount of fan cooling needed
For fan cooling, each temp sensor will have two levels.
TEMP_FAN_OFF
* At or below this temperature, no active cooling is needed.
TEMP_FAN_MAX
* At or above this temperature, active cooling should be running at maximum.
The highest level of all temp sensors will be used to request the amount of
active cooling needed. The function pwm_fan_percent_to_rpm() is invoked to
convert the amount of cooling to the target fan RPM.
The default pwm_fan_percent_to_rpm() function converts smoothly between the
configured CONFIG_PWM_FAN_RPM_MIN and CONFIG_PWM_FAN_RPM_MAX for percentages
between 1 and 100. 0% means "off".
The default function probably provide the smoothest and quietest behavior,
but individual boards can provide their own pwm_fan_percent_to_rpm() to
implement whatever curves, hysteresis, feedback, or other hackery they wish.
BUG=chrome-os-partner:20805
BRANCH=none
TEST=manual
Compile-time test with
make BOARD=falco runtests
On the EC console, the existing fan commands should work correctly:
faninfo - display the fan state
fanduty NUM - force the fan PWM to the specified percentage (0-100)
fanset RPM - force the fan to the specified RPM
fanset NUM% - force the fan to the specified percentage (0-100) between
its configured minimum and maximum speeds from board.h
(CONFIG_PWM_FAN_RPM_MIN and CONFIG_PWM_FAN_RPM_MAX)
fanauto - let the EC control the fan automatically
You can test the default pwm_fan_percent_to_rpm() with
fanset 1%
faninfo
The fan should be turning at CONFIG_PWM_FAN_RPM_MIN. Let the EC control it
automatically again with
fanauto
Also on the EC console, the thermal settings can be examined or changed:
> temps
PECI : 327 K = 54 C
ECInternal : 320 K = 47 C
G781Internal : 319 K = 46 C
G781External : 318 K = 45 C
>
> thermalget
sensor warn high shutdown fan_off fan_max name
0 373 387 383 333 363 PECI
1 0 0 0 0 0 ECInternal
2 0 0 0 0 0 G781Internal
3 0 0 0 0 0 G781External
>
> help thermalset
Usage: thermalset sensor warn [high [shutdown [fan_off [fan_max]]]]
set thermal parameters (-1 to skip)
>
> thermalset 2 -1 -1 999
sensor warn high shutdown fan_off fan_max name
0 373 387 383 333 363 PECI
1 0 0 0 0 0 ECInternal
2 0 0 999 0 0 G781Internal
3 0 0 0 0 0 G781External
>
From the host, ectool can be used to get and set these parameters with
nearly identical commands:
ectool thermalget
ectool thermalset 2 -1 -1 999
Change-Id: Idb27977278f766826045fb7d41929953ec6b1cca
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66688
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The BOOTCFG register configures a couple of important things: whether to
allow jumping into the builtin ROM bootloader at reset, and whether or not
to allow JTAG access for programing and debugging.
The default is "no" and "yes". But the BOOTCFG register can be locked so
that it can't be changed again, which means that if the wrong values are put
into it, the system is pretty much bricked.
On Link, we wrote a BOOTCFG value that allowed a GPIO to be used as a bypass
to optionally trigger the ROM bootloader, but on Slippy and its derivatives
that GPIO is not pulled up. If you program the Link values into BOOTCFG on a
Slippy, the system is stuck in the ROM bootloader more or less forever.
This change disables that GPIO, keeps JTAG enabled, and locks those settings
for all LM4 chips (it's a chip config now, not a board config). We've never
actually used the GPIO to invoke the ROM bootloader, but we have managed to
brick a number of systems just by having it enabled, so we're going to lock
it into a safe configuration now.
BUG=chrome-os-partner:19247
BRANCH=falco,peppy
TEST=manual
Reflash, boot, power cycle (actually unplug the EC from AC and battery) a
few times. It should continue to work.
Change-Id: Iaf1a81d6814104421a56425490e3d5164ea9b617
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66538
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This tests that command history is as expected. Also fix a bug that some
checks in console_edit test are skipped.
BUG=chrome-os-partner:19236
TEST=Pass console_edit test.
BRANCH=None
Change-Id: Ifbd3d1690f25b35bf5efe523e656b013aa534d26
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/64837
BUG=chrome-os-partner:21847
BRANCH=peppy
TEST=Manual. Check state of GPIO_P5000_FAN_EN with lid open
and lid closed. Can also check with meter via TP109.
Change-Id: I8a64c14d53dd84a5d586c0abb04ccb71de0e78b3
Signed-off-by: Dave Parker <dparker@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65674
We often need to watch for transitions between one state and another, so
that we can issue warnings or take action ONCE. This abstracts that "have I
already reacted to this" stuff into a single set of functions.
For example, this code reads a GPIO every time through the loop, but it only
generates an event when the GPIO value changes from 0 to 1:
cond_t c;
cond_init_false(&c);
while(1) {
int val = read_some_gpio();
cond_set(&c, val);
if (cond_went_true(&c))
host_event(SOMETHING_HAPPENED);
sleep(1);
}
BUG=none
BRANCH=falco,peppy
TEST=manual
make BOARD=falco runtests
Change-Id: I42393fcf3c4eb71b9551118a0f442d55c0691315
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65071
Only link actually used this function, but all batteries were required
to provide an (empty) implementation. Use
CONFIG_BATTERY_VENDOR_PARAMS to gate this functionality, so non-link
battery code can be simpler.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms and pass unit tests
Change-Id: Ic2c6dd1163a981e48873d798f77891cc7de1f8cf
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65257
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Rong Chang <rongchang@chromium.org>
Read status, set temperature alert thresholds, get and set
configuration options. I2c offsets and status/config register
bits are documented in temp_sensor_g781.h
Usage by example:
g781 - Print status info
g781 settemp 0x0e 12 - Set remote low temp alarm to 12C
g781 setbyte 0x09 0x40 - Enable single-shot mode
g781 getbyte 0xfe - Read device ID
BUG=None
BRANCH=falco,peppy
TEST=Manual. Run g781 console command
Signed-off-by: Dave Parker <dparker@chromium.org>
Change-Id: Id051f79ea643255d57c3fc694b7ae685a6611c81
Reviewed-on: https://gerrit.chromium.org/gerrit/65234
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Dave Parker <dparker@chromium.org>
Tested-by: Dave Parker <dparker@chromium.org>
