To implement rtc driver for some ec chips, we
need to convert between calandar date and seconds
(since epoch time, 01-01-1970 00:00:00).
Sicne these functions are HW-independent, let's add
common/rtc.c, include/rtc.h, and unit test for this.
BUG=b:63908519
BRANCH=none
TEST=make buildall test -j
Change-Id: Icb1e768d2b3674d5225b83e09475e984eb104d06
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/666985
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
The WebUSB specification defines a specific Platform Descriptor in the
Binary Object Store:
https://wicg.github.io/webusb/#webusb-platform-capability-descriptor
This descriptor provides a special 'Landing page' URL to the host
browser and associated privileges for it.
Bump the USB version for BOS descriptors to 2.1 to be compatible with
Chrome implementation.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BUG=none
BRANCH=twinkie
TEST=manual: on Twinkie (chip/stm32) and HG proto2 (chip/g), enumerate
WebUSB descriptors with lsusb and connect to a WebUSB page in Chrome
R61+.
Change-Id: I7211ab554f4a6c156c1e8e79a3d9f0d6644217c6
Reviewed-on: https://chromium-review.googlesource.com/664813
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This change allows chipset and board to perform any action when host
indicates intention to enter sleep state. Chipset can take action like
enable/disable power signal interrupts and boards can enable/disable
decay of VRs on host intent to enter/exit S0ix.
BUG=b:65732924
BRANCH=None
TEST=make -j buildall
Change-Id: I6298825d4ee96a07b93523c2f366527ae2be8a27
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/677498
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Chromebox ECs performs EFS: verifying firmware before the AP boots.
This patch updates host commands which are required for the EFS.
When EC_REBOOT_FLAG_SWITCH_RW_SLOT is specified, EC_CMD_REBOOT_EC
changes the active slot before it reboots the system.
BUG=b:65264494
BRANCH=none
TEST=On Fizz, verify:
1. RW_B is old and updated by soft sync. RW_B is activated and
executed after reboot. System continues to boot to OS.
2. RW_A is old and updated by soft sync. RW_A is activated and
executed after reboot. System continues to boot to OS.
Change-Id: I08050c985ce0b27b30cb842e6b5b4660f32e5211
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/648450
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
When EFS finds the active slot is invalid, it tries the other slot.
This patch makes the other slot active so that the following boots
will try the other slot first.
This patch also replaces enum flash_rw_slot with system_image_copy_t.
The new APIs are therefore renamed from *_slot to *_copy. Basically,
this makes vboot see slots as a conceptual place instead of physical
spaces bound to flash storage.
BUG=b:65028930
BRANCH=none
TEST=On Fizz, verify:
1. RW_B is old and updated by soft sync. RW_B is activated and
executed after reboot. System continues to boot to OS.
2. RW_A is old and updated by soft sync. RW_A is activated and
executed after reboot. System continues to boot to OS.
Change-Id: Icf97da13e651e7a931b9d507052b9422566eb16c
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/648449
This will be used by the updater to first check that the touchpad
FW on AP side matches the one for which we stored hashes on EC
side.
This guarantee that we do not accidentally try to flash an
incorrect FW, which would render the touchpad non-functional.
BRANCH=none
BUG=b:63993173
TEST=make TOUCHPAD_FW=SA459C-1211_ForGoogleHammer_3.0.bin \
BOARD=hammer -j
TEST=./usb_updater2 -t
includes output of
sha256sum A459C-1211_ForGoogleHammer_3.0.bin
Change-Id: Id30ab2d7c7d7e2d0f25cc893f685d218c44c022e
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/641736
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Based on the passed TOUCHPAD_FW parameter to the make command, the
build system generates hashes for the touchpad FW.
To generate the hashes, gen_touchpad_hash splits the touchpad FW
in blocks of CONFIG_UPDATE_PDU_SIZE, that are hashed individually
(SHA-256), and then stored in the EC image.
This will allow the USB updater code to verify the integrity of
the touchpad firmware being flashed.
When no FW is provided, zeros are output, which do not match
any valid data.
BRANCH=none
BUG=b:63993173
TEST=make TOUCHPAD_FW=SA459C-1211_ForGoogleHammer_3.0.bin \
BOARD=hammer -j
TEST=Using variations of
make TOUCHPAD_FW=SA459C-1211_ForGoogleHammer_3.0.bin \
BOARD=hammer -j
make TOUCHPAD_FW=SA459C-1211_ForGoogleHammer_4.0.bin \
BOARD=hammer -j
make BOARD=hammer -j
Check that TPHASH touchpad_fw_hash.h is only regenerated when
the parameter changes.
Change-Id: Ie347270aa9c00342de13489c9422e45e681b94c2
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/615321
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This patch adds USB_CHG_TYPE_DEDICATED to enum usb_chg_type. It's
for dedicated AC adapters like a barrel jack adapter used for Fizz.
BUG=b:65591971
BRANCH=none
TEST=make buildall
Change-Id: Ib883c97eb5e468753c73453d7dedd228547ae025
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/665327
Reviewed-by: Shawn N <shawnn@chromium.org>
This patch gives the highest priority to dedicated chargers. It
means if a dedicated power supply is being connected, other power
supplies such as USB-C adapters will not be recognized as a new
charger.
BUG=b:65059574
BRANCH=none
TEST=Boot Fizz on BJ adapter. Verify plugging in Type-C adapter
doesn't shut down the system.
Change-Id: Ie49b128ae64f917a227f9081148565a3f5356212
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/655638
Reviewed-by: Shawn N <shawnn@chromium.org>
1. Add a new config option CONFIG_PORT80_PRINT_IN_INT which is
disabled by default to disable printing of port80 messages in
interrupt context.
2. If CONFIG_BRINGUP is defined, redefine CONFIG_PORT80_PRINT_IN_INT
to enable printing of port80 messages in interrupt context for boards
that are in bringup phase.
3. If print_in_int is disabled, add a deferred call to dump port80
buffer to EC console 4 seconds after the last port80 message is
received.
BUG=b:64196191
BRANCH=None
TEST=Verified following:
1. make -j buildall
2. Port80 messages are not printed by default on Soraka
3. Port80 buffer is dumped 4 seconds after last port80 message, if
BIOS is stuck for 4 seconds, in recovery mode and when reboot from AP
console.
4. Boot time on soraka went down from ~1.59seconds to ~1.45 seconds in
EC reboot case (savings of ~140ms).
Change-Id: I9aee0987765f905b4ac49d04ffc54d71ee3a04f9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/661880
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The modified CRC8 implementation didn't detect some errors. For
example, using the modified CRC8: CC5QQLALU and DC5QQLALU calculates
to the same value.
BUG=b:37952913
BRANCH=none
TEST=make buildall
Used online CRC-5-USB calculator to test several values against
this implementation.
Signed-off-by: Sam Hurst <shurst@chromium.org>
Change-Id: I5a17941e25691872a25b41525f65f36e2ed1d4fa
Reviewed-on: https://chromium-review.googlesource.com/660812
Commit-Ready: Sam Hurst <shurst@google.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Michael Tang <ntang@chromium.org>
Chromebox ECs performs EFS: verifying firmware before the AP boots.
This patch updates host commands which are required for the EFS.
The change includes:
* Update EC_CMD_FLASH_REGION_INFO to accept EC_FLASH_REGION_UPDATE
* Update EC_CMD_VBOOT_HASH to accept EC_VBOOT_HASH_OFFSET_UPDATE
When EC_FLASHS_REGION_UPDATE is specified, EC_CMD_FLASH_REGION_INFO
returns the slot which currently is not hosting a running RW copy.
When EC_VBOOT_HASH_OFFSET_UPDATE is specified, EC_CMD_VBOOT_HASH
computs the hash of the update slot. This hash covers the entire
region, including the signature at the end.
This patch undefines CONFIG_CMD_USBMUX and CONFIG_CMD_TYPEC
for gru to create space.
BUG=b:65028930
BRANCH=none
CQ-DEPEND=CL:648071
TEST=On Fizz, verify:
1. RW_B is old and updated by soft sync. RW_B is activated and
executed after reboot. System continues to boot to OS.
2. RW_A is old and updated by soft sync. RW_A is activated and
executed after reboot. System continues to boot to OS.
Change-Id: I9ece907b764d07ce94054ba27996e048c665a80a
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/648448
Reworked suzy-q and suzy-qable all provide Rp, so there is no need for
special detection handling in S5. Also, CONFIG_USB_PD_QUIRK_SLOW_CC_STATUS
is no longer relevant, since we no longer take special action when VBUS
is seen without Rp.
BUG=chromium:737755
BRANCH=None
TEST=On kevin, verify reworked suzy-q and suzy-qable are detected in S5.
Also, verify zinger works in S5 on reef.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I50967bd6415d964a038b2e7d134374132eda11ec
Reviewed-on: https://chromium-review.googlesource.com/656067
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Servo / Suzy-Q related debugging methods is a big challenge
in factory especially after servo debug header is removed.
Expose some information to OS from EC will do a great help
for massive production.
+ expose charge/battery related state to ectool
1. chg_ctl_mode
2. manual_mode
3. battery_seems_to_be_dead
4. battery_seems_to_be_disconnected
5. battery_was_removed
6. disch_on_ac (learn mode state)
BUG=b:65265543
BRANCH=master
TEST=`ectool chargestate param 0x20000~0x20006 get correct state`
Change-Id: Ic2ed38e2eb9def01be29729fa1fe1959eb73fe43
Signed-off-by: Ryan Zhang <ryan.zhang@quanta.corp-partner.google.com>
Reviewed-on: https://chromium-review.googlesource.com/646412
Reviewed-by: Shawn N <shawnn@chromium.org>
Minor cleanup to the 'ccd help' command.
Add 'ccd get' as a clearer alias to print the config.
Change CONFIG_CMD_CCDDISABLE to CONFIG_CMD_CCD_DISABLE to indicate
that it's a sub-command for 'ccd'.
BUG=b:65407395
BRANCH=cr50
TEST=manual
ccd -> see clue for 'ccd help'
ccd help -> see 'get' command
ccd get -> prints config
ccd disable -> error (config option isn't defined by default)
Change-Id: Icbcaa178171ca948cfaae58ab1a1e73ab3d95243
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/654380
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
For historical reasons, CCD, reset, and power button control were
scattered around several files. Consolidate the code in more sensible
(in retrospect) places.
No functional changes, just moving code.
BUG=none
BRANCH=cr50
TEST=make buildall; boot cr50
Change-Id: Ic381a5a5d0627753cc771189aa377e88b81b155e
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/653766
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
SYSTEM_IMAGE_RW_B hasn't been globally treated as a RW copy.
This change makes EC treat it also as a RW copy.
BUG=none
BRANCH=none
TEST=make buildall
Change-Id: Iae5a9090cdf30f980014daca44cdf8f2a65ea1f2
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/656337
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Default setting of embedded flash's clock is 24 or 32 MHz
and PLL is 48 or 96 MHz correspondingly.
And it8320 supports e-flash clock up to 48 MHz,so we add
a new config option to support it.
BRANCH=none
BUG=none
TEST=Run FAFT with e-flash 48MHz and test results are passed.
Change-Id: I096ae3abc8fec9bd7e0556c57605e87a31ac3b07
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-on: https://chromium-review.googlesource.com/645466
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In USB FS on a bulk/interrupt endpoint, the transactions normally toggles
between DATA0 and DATA1 PIDs.
After a USB suspend/resume cycle, we need to restart from the PID we
were at before suspend.
In our current code, when going to deep-sleep during USB suspend, we are
re-initializing everything when the MCU restarts at each resume. So we set
implicitly the PID to DATA0. The USB Hardware IP just silently discards the
packet when the PID of an incoming OUT packet is not matching the
expectation in the endpoint register.
In order to preserve DATA PIDS, record the state of the PID toggling on
each endpoint when going to deep-sleep and restore it during the USB
initialization.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:38160821
TEST=manual, plug a HG proto2 on a Linux host machine and enable
'auto-suspend' for this USB device. Let it go to sleep and wake-it up by
sending a U2FHID request. Repeat the process several times and see that
the key answers every time (while it was failing after the second cycle
before).
Change-Id: I75e2cfc39f22483d9e9b32c5f8b887dbafc37108
Reviewed-on: https://chromium-review.googlesource.com/655238
Commit-Ready: Marius Schilder <mschilder@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Marius Schilder <mschilder@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Currently, the Cr50 state machines (EC, AP, RDD, bitbang, etc.) manage
their own enabling and disabling of the ports (UART, SPI, etc.) This
is tricky because the rules for when ports should be enabled are
non-trivial and must be applied in the correct order. In additionl
the changes all need to be serialized, so that the hardware ends up in
the correct state even if multiple state machines are changing
simultaneously.
Consolidate all of that into chip/g/rdd.c. The debug command for it
is now 'ccdstate', which just prints the state machines. This will
allow subsequent renaming of the 'ccdopen', etc. commands to 'ccd
open', etc.
Also include UART bit-banging into that state which must be
consistent. Previously, it was possible for bit-banging to leave UART
TX connected, instead of returning it to the previous state.
Use better names for CCD config fields for UART. I'd had them backwards.
BUG=b:62537474
BRANCH=cr50
TEST=manual, with a CR50_DEV=1 image
1) No servo or CCD
Pull SERVO_DETECT low (disconnected)
Pull CCD_MODE_L high (disabled)
Pull EC_DETECT and AP_DETECT high (on)
Reboot. RX is enabled even if cables are disconnected so we buffer.
ccdstate -> UARTAP UARTEC
Pull EC_DETECT low.
ccdstate -> UARTAP
Pull EC_DETECT high and AP_DETECT low.
ccdstate -> UARTEC
Pull AP_DETECT high.
ccdstate -> UARTAP UARTEC
2) Servo only still allows UART RX
Pull SERVO_DETECT high (connected).
ccdstate -> UARTAP UARTEC
3) Both servo and CCD prioritizes servo.
Pull CCD_MODE_L low (enabled).
ccdstate -> UARTAP UARTEC
Reboot, to make sure servo wins at boot time.
ccdstate -> UARTAP UARTEC
Bit-banging doesn't work when servo is connected.
bitbang 2 9600 even -> superseded by servo
bitbang -> disabled
ccdstate -> UARTAP UARTEC
4) CCD only allows more ports and remembers we wanted to bit-bang
Pull SERVO_DETECT low.
ccdstate --> UARTAP+TX UARTEC+BB I2C SPI
bitbang 2 disable
ccdstate --> UARTAP+TX UARTEC+TX I2C SPI
Reboot and see we don't take over servo ports until we're
sure servo isn't present.
ccdstate --> UARTAP UARTEC (for first second)
ccdstate --> UARTAP+TX UARTEC+TX I2C SPI (after that)
5) Bit-banging takes over ECTX
bitbang 2 9600 even
bitbang -> baud rate 9600, parity even
ccdstate -> UARTAP+TX UARTEC+BB I2C SPI
bitbang 2 disable
ccdstate -> UARTAP+TX UARTEC+TX I2C SPI
6) Permissions work. Allow easy access to full console and ccdopen:
ccdset OpenNoTPMWipe always
ccdset OpenNoLongPP always
ccdset GscFullConsole always
Default when locked is full AP UART EC RO, no I2C or SPI
ccdlock
ccdstate -> UARTAP+TX UARTEC
No EC transmit permission means no bit-banging
bitbang 2 9600 even
bitbang -> disabled
ccdstate -> UARTAP+TX UARTEC
But it remembers that we wanted to
ccdopen
ccdstate -> UARTAP+TX UARTEC+BB I2C SPI
bitbang 2 disable
ccdstate -> UARTAP+TX UARTEC+TX I2C SPI
Try turning on/off permissions
ccdset UartGscTxECRx always
ccdlock
ccdstate -> UARTAP+TX UARTEC+TX
No read means no write either
ccdset UartGscRxECTx ifopened
ccdlock
ccdstate -> UARTAP+TX
ccdopen
ccdset UartGscRXAPTx ifopened
ccdlock
ccdstate -> (nothing)
Check AP transmit permissions too
ccdopen
ccdset UartGscRxAPTx always
ccdset UartGscTxAPRx ifopened
ccdlock
ccdstate -> UARTAP
Check I2C
ccdopen
ccdset I2C always
ccdlock
ccdstate -> UARTAP I2C
SPI port is enabled if either EC or AP flash is allowed
ccdopen
ccdset flashap always
ccdlock
ccdstate -> UARTAP I2C SPI
ccdopen
ccdset flashec always
ccdset flashap ifopened
ccdlock
ccdstate -> UARTAP I2C SPI
Back to defaults
ccdoops
Change-Id: I641f7ab2354570812e3fb37b470de32e5bd10db7
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/615928
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Currently, only usb_pd_protocol.c cares about the actual ccd mode
(disabled/partial/enabled). Everything else just cares whether it's
enabled or not. So promote the boolean ccd_is_connected() from
board/cr50 up to chip/g, and rename it to ccd_ext_is_enabled() to
match the new nomenclature (since 'CCD' itself is now too overloaded).
This will make it easier to handle CCD state directly in board/cr50
after we split it from common/case_closed_debug.c
BUG=none
BRANCH=cr50
TEST=make buildall; boot cr50; make sure USB endpoints still work
Change-Id: Ic3df7467bfe29f1c5d7060cac1309a1f0e090d9e
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/648212
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
CCD_CHANGE_HOOK should use CONFIG_CASE_CLOSED_DEBUG_V1.
All boards which use chip/g either use both CONFIG_USB_SERIALNO and
CONFIG_CASE_CLOSED_DEBUG or neither of them, so just depend on
CONFIG_USB_SERIALNO.
This is in preparation for making common/case_closed_debug refer only
to the usb_pd_protocol version (with mode=disabled/partial/enabled),
and cr50 will have its own version (with only enabled/disabled, and
tied more closely to CCD config).
No functionality changes.
BUG=none
BRANCH=cr50
TEST=make buildall -j; boot cr50 and see change hook called
Change-Id: I1985c8c48c1a85fed4549402a7b47b8a9cf135d7
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/648067
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Implement keyboard backlight control through HID output report. One
could enable CONFIG_USB_HID_KEYBOARD_BACKLIGHT to enable keyboard
backlight support for a given board. Target board must implement the
`void board_set_backlight(int brightness)` function in order correctly
set backlight.
BRANCH=none
BUG=b:37971411,b:63364143
TEST=with follow up CLs
1. `make BOARD=hammer -j`
2. `echo 10 > /sys/class/leds/hammer\:\:kbd_backlight/brightness`
console shows 'Keyboard backlight set to 10%'
Change-Id: Ibeff510a0d996ddebf61b54ed6b500b02c35564a
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://chromium-review.googlesource.com/586348
Commit-Ready: Wei-Ning Huang <wnhuang@chromium.org>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Allow reporting that keyboard backlight doesn't exist even when the code
is compiled in. Useful if there are multiple device models that should
share firmware.
BUG=b:64705535
BRANCH=none
TEST=none
Change-Id: I9c1fc370aedf66ef856a571f73831095d27e3d39
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://chromium-review.googlesource.com/633926
Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to test certain devices in the test lab using cased closed
debugging (CCD), we need a mechanism to programmatically "press" the
recovery button. Even though this signal is being buffered through the
EC to the AP, and the EC could theoretically set it if needed, we cannot
trust the EC in its RO image since it may speak to the outside world
over USB PD.
Instead, this commit introduces a console command on cr50 that can be
used to force the recovery button state to be pressed. However, it is
gated behind the CCD capabilities defaulting to the IfOpened state.
Additionally, a new vendor command is added to query the trusted state
of the recovery button. The AP should use this command instead of
trusting the GPIO connected to it.
BUG=b:37751915, b:64146626
BRANCH=cr50
TEST=Flash cr50. Press KEY0, verify that reported rec btn follows the
state of the button.
TEST=`recbtnforce enable` causes the button to be reported as pressed.
Physical presses of the button do not alter the reported state.
TEST=`recbtnforce disable` causes the reported state to follow that of
the physical button.
TEST=The `recbtnforce` command is set to the IfOpened capability by
default.
TEST=CCD locking the DUT and attempting to force the recovery button
results in an error of access denied. The physical state is reported.
TEST=From the AP, issue the vendor command to retrieve the button state
and verify that it behaves as expected.
Change-Id: Ib8c2928e75e5f9a1a83c5361664efc3fa0ae2ddb
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/635955
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
For some boards, the control lines to the charging port controller are
all tied to a power rail. In essence, this leaves the ILIM_SEL as the
only signal able to be controlled, which means that we only support
CDP/SDP.
This commit adds a new CONFIG_* option which describes this.
CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY
Additionally, some cleanup is made to not always assume the number of
smart power ports.
BUG=None
BRANCH=None
TEST=make -j buildall
Change-Id: I080ccd67ffc20ccccf1e6b33a3cf9374a6b70ad6
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/634274
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
For system using core/minute-ia, build will fail since __image_size is
not defined. If later this variable is used, should adjust its value
properly.
BUG=none
BRANCH=None
TEST=Build passed for Soarka ISH which uses core/minute-ia.
Change-Id: I8e179e0bac551a46d93ca10ba8b61b4ebade74fc
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/595151
Commit-Ready: Li1 Feng <li1.feng@intel.com>
Tested-by: Li1 Feng <li1.feng@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Currently, chip/g uses jtag_pre_init() to do some chip
pre-initialization that isn't actually related to JTAG. This has been
harmless, but it's currently the only chip which actually does "JTAG"
pre-init, and we'd like to get rid of that. So, move that
functionality to a new optional chip_pre_init() function.
BUG=chromium:747629
BRANCH=cr50
TEST=make buildall
boot cr50
make all dis; confirm chip_pre_init() is called early in <main>
Change-Id: I3cae0747ab0c3cc974fce9f108947207b38e035f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/629876
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
When the board level TCPC run as an init hook it will frequently
lead to an EC reset when we are trying to recovery a disconnected
battery, potentially even a reboot loop with the most unlucky
timing.
If we instead call it from the pd_task before tcpc_init is called
then the board init hook can stall the pd_task init until the
battery is out of disconnect mode, or giving up after 2 seconds
in case the battery never seems to recover.
This accomplishes two goals: ensure the PD chips are not reset until
the battery is out of disconnect and delay start of the pd_task
(and PD negotiation) until the battery is out of disconnect state.
This change was done in the Eve FW branch. Pulling it into TOT so it
can be used for other boards that have the same
issue. https://chromium-review.googlesource.com/c/592716. The change
to wait for the battery to be out of disconnect mode is in the board
specific board_tcpc_init() function and so will be in subsequent board
specific CLs.
BUG=b:63957122
BRANCH=none
TEST=manual Verify that 'make buildall' is successful.
Change-Id: I14c3dbb89cdc05fa9231fbe9db2e1de19fa941b6
Signed-off-by: Scott Collyer <scollyer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/627114
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to satisfy factory testing requirements we need to
boot a bare board with just an AC adapter without requiring
a power button.
However we also don't want to always allow booting of the
battery is present but cut-off (which will indicate BP_NO so
we can't use the existing battery_is_present function) or has
critically low level as it may not immediately boot.
To accomplish this add a function that allows the board to
specify a custom "hardware presence" for the battery that is
separate from the battery presence check.
This CL is taking a change done for Eve and pulling into TOT so it can
be used for other projects that have the same
requirements. https://chromium-review.googlesource.com/c/582544
BUG=b:63957122
BRANCH=none
TEST=manual
Change-Id: Ib1dc4f659adbf0eebd3dc8c3c61b39b8fa36cb4a
Signed-off-by: Scott Collyer <scollyer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/627113
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We want to be able to collect statistics of the i2c bus problems. This
patch logs an event each time the wedged bus recovery happens.
BRANCH=cr50
BUG=b:63760920
TEST=with the upcoming patches verified that i2c recovery events are
logged as expected.
Change-Id: I1241b2dece33f89cd724d53a48f94e17f4415c62
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/620114
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
SVr4/4.3BSD/C89/C99 use a return value of size_t. To
make interaction with code running on both userland
and on the EC easier, change our function prototype
to return size_t as well.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
BRANCH=none
BUG=none
TEST=make buildall -j works
Change-Id: I0f097c4d0db4232d888e1d54e6c1d22f4859a112
Reviewed-on: https://chromium-review.googlesource.com/618269
Commit-Ready: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
We use the unofficial, Windows 8, Relative Scan time HID usage
(Digitizer page, 0x56) to add timestamps to our HID touchpad
events.
The timestamps is a rolling, unsigned, 16-bit integer, with a
resolution of 100us (so it wraps around every 6.5s).
The host will be able to synchronize to that timestamp, resetting
an offset every time the touchpad is quiet a certain amount of
time (e.g. 1 second).
BRANCH=none
BUG=b:63685117
TEST=Flash hammer, timestamps are reported in HID descriptor.
Change-Id: Ie5d56a9df14e464d2cdcd559f550d6e3cc81961f
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/603041
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add a shared library to export task information.
Modified the stack analyzer to get information from the shared library.
Show allocated stack sizes of tasks in the stack analyzer.
To get the all task information (including the allocated stack size),
A shared library is added and compiled with the board to export all
configurations of the tasklist.
BUG=chromium:648840
BRANCH=none
TEST=extra/stack_analyzer/stack_analyzer_unittest.py
make BOARD=elm && extra/stack_analyzer/stack_analyzer.py \
--objdump=arm-none-eabi-objdump \
--addr2line=arm-none-eabi-addr2line \
--export_taskinfo=./build/elm/util/export_taskinfo.so \
--section=RW \
./build/elm/RW/ec.RW.elf
make BOARD=${BOARD} SECTION=${SECTION} analyzestack
Change-Id: I72f01424142bb0a99c6776a55735557308e2cab6
Signed-off-by: Che-yu Wu <cheyuw@google.com>
Reviewed-on: https://chromium-review.googlesource.com/611693
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Add a static analysis tool for firmware stack usage.
Add an new Makefile rule to analyze the stack usages of firmwares.
Details about the tool can be found in extra/stack_analyzer/README.md.
BUG=chromium:648840
BRANCH=none
TEST=extra/stack_analyzer/stack_analyzer_unittest.py
make BOARD=elm && make BOARD=elm build/elm/RW/ec.RW.taskinfo && \
extra/stack_analyzer/stack_analyzer.py \
--objdump=arm-none-eabi-objdump \
--addr2line=arm-none-eabi-addr2line \
./build/elm/RW/ec.RW.elf ./build/elm/RW/ec.RW.taskinfo
make BOARD=${BOARD} SECTION=${SECTION} analyzestack
Change-Id: Ifb1b5f5ad6be8f8b125b14d6ee03e25cb385895b
Signed-off-by: Che-yu Wu <cheyuw@google.com>
Reviewed-on: https://chromium-review.googlesource.com/576411
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
