When system is locked, the console is disabled. However, we need console
for debugging and testing. This CL uses a bit from back-up register to
indicate if the console should always be enabled. (This bit is currently
used by fake WP, which is removed in this CL.) With this, we can set
this bit with console command 'forceen 1' to ensure console is never
disabled.
To prevent device shipped in this state, the chip name is postfixed with
'-unsafe' so that the device is not able to pass HWID check.
BUG=chrome-os-partner:19293
TEST=Manual
BRANCH=spring
Change-Id: I88556e973ca542c1bdc27ba64988718291e01a26
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51086
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The 5V rail should be enabled on S5->S3 transitions and
disabled on S3->S5 transitions.
BUG=chrome-os-partner:19398
BRANCH=none
TEST=successful state transitions: S0,S3,S5,G3
Change-Id: If9fd7ef16f015136238dd18f64602ecf33d9ec4a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51359
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The PROCPWRGD signal is not well documented. It's not known if
it is an input or an output. Emperically it was discovered that
driving this pin during the resume path causes resume to fail.
Therefore, ignore the pin by setting it to an input.
BUG=chrome-os-partner:19398
BRANCH=none
TEST=successful state transition from S0 to S3 and back to S0
Change-Id: I55dc16c75c286af06806e2513197f0bb2c7b9d04
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51358
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The current sense resistor has changed. Update constant here to reflect
the new values for DVT1.
BUG=None
TEST=Build Spring
BRANCH=Spring
Change-Id: Ib27c45cef569fa758db2fbb428150c8c2b6732ef
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49892
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
- pass through the eDP VDD enable from PCH
- Bring up suspend rail after DPWROK and before RSMRST,
as indicated for deep sleep sequencing
- de-assert CPU_PGOOD on S0->S3 transition, it was
getting left enabled
BUG=chrome-os-partner:19398
BRANCH=none
TEST=successful state transition from G3 to S0 and back to G3
Change-Id: Ie711275d6121edccff60b2de08b71575d2d035b7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51154
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
As our stack for the keyboard scanning task might be small (256 bytes on
STM32), we store the full keyboard state in a global instead of the
stack to avoid consuming 16 bytes there.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:19389
TEST=run on Spring with CONFIG_OVERFLOW_DETECT and see that the KEYSCAN task
is now consuming 248 bytes of stack instead of 264.
Change-Id: I2dd7815f36e6807e7b9e88d59f8fd8a14b1988ab
Reviewed-on: https://gerrit.chromium.org/gerrit/51028
Reviewed-by: Vic Yang <victoryang@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Still some work to do here but this now works.
NOTE: This makes the system behave like a normal
cros device where the power is applied automatically.
For some (other, unknown) reason the "reboot ap-off"
is not passing flags correctly to keep it off.
BUG=chrome-os-partner:19398
BRANCH=none
TEST=successful state transition from G3 to S0
Change-Id: I694136b9611e18ac8fb7b1e960bd10caa258ce28
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51077
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
If the user unplug video dongle before it is detected and handled, we
may be stuck with ID_MUX=1 and interrupt from TSU6721 disabled. This
essentially breaks charging.
BUG=chrome-os-partner:18997
TEST=Build and check charging port still works.
BRANCH=spring
Change-Id: I93e69287d07947fef743b4674857e52c26513835
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50969
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
We cannot know how much current we can pull from video dongle, so let's
just try to pull as much as possible up to 2A.
BUG=chrome-os-partner:19324
TEST=Plug in video dongle and see 3.3V output.
TEST=Plug in video dongle with supplied charger, and see 50% PWM duty
cycle.
TEST=Plug in video dongle with normal charger, and see 70~80% PWM duty
cycle.
BRANCH=spring
Change-Id: I8b503f886fcafaa11e6757a5059ce673a8ed53cc
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50963
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The help text says to pass 0 or 1 for the mode but
the code only accepts "on" or "off".
Fix up the help text to match and have the display
output for the port status also use on/off so it is
consistent with the input.
BUG=chrome-os-partner:18825
BRANCH=none
TEST=manual: verify "usbchargemode 0 on" works as
it is explained in the help text.
Change-Id: Ib32dc68af93989d277aa84a1cb53ae9b66a8b595
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50838
SPI is always enabled on pit, so remove #ifdefs
SPI1_CLK was aliased to AC_STATUS, which is left over from snow and
doesn't exist on pit. That caused it to be driven high briefly during
EC boot.
Also set SPI pins for 40MHz speed so we can try faster SPI clock.
BUG=chrome-os-partner:19304
BRANCH=none
TEST=boot system; sspi 2:0 256 9f prints a bunch of FDs then FEEC010001
Change-Id: I10352cff3669d6a087939d9d8e302d70708e9ee3
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51023
Reviewed-by: Doug Anderson <dianders@chromium.org>
This commits the hacks made during board bringup. Bugs can be filed and
fixed based on this starting point.
BUG=chrome-os-partner:18825
BRANCH=slippy
TEST=manual
Try it and see.
Change-Id: Ia663eaf9a357633873b1b5d5cc6dbdda63513082
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50875
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Several test utility macros have been duplicated across tests. Let's put
them in a single place.
BUG=chrome-os-partner:19236
TEST='make runtests', 'BOARD=spring make tests'
BRANCH=None
Change-Id: Ib0c9f829715425cc23e33b8ef456b17dfadab13c
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50513
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The spec suggests we cannot reliably go over 1.5A and gracefully
recover. Let's avoid going over that limit.
BUG=chrome-os-partner:19267
TEST=Build spring
BRANCH=spring
Change-Id: I07411ff3ce4107e0289c5af5365ef5a23fd23e4e
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50321
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This includes:
- Increase overcurrent retry count from 1 to 2.
- Mark overcurrent event regardless of what current PWM duty cycle is.
- PWM duty cycle settles faster.
- PWM duty cycle starts from ~100%.
BUG=chrome-os-partner:19001, chrome-os-partner:19037
TEST=Manual
BRANCH=spring
Change-Id: Idf007fb589fde3baef6c8975dfa1f2fc1ec6e95d
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50262
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Perviously we use uint32_t for this, but this doesn't compile for 64-bit
environment (and likely doesn't for 16-bit either.) Use uintptr_t so that
we don't get size mismatch errors.
BUG=chrome-os-partner:19257
TEST=Run host emulated tests
BRANCH=None
Change-Id: I3cd66a745fa171c41a5f142514284ec106586acb
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50358
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This is the first version of pthread-based RTOS emulator. With this, we
will be able to test high-level modules entirely on the host machine.
BUG=chrome-os-partner:19325
TEST='make runtests' and see tests passing.
BRANCH=None
Change-Id: I1f5fcd76aa84bdb46c7d35c5e60ae5d92fd3a319
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49954
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The EC currently assumes the AP only provides USB power during S0, which
is incorrect. This CL adds S3 so that it behaves when the device is
suspended.
BUG=chrome-os-partner:19190
TEST=Suspend and unplug power. Doesn't hear clicking sound.
BRANCH=Spring
Change-Id: Ice1421bda55b2fee408ba062ed3de7a697ccd0c8
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50093
Reviewed-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This specifies the Slippy GPIOs. Because the power controls are completely
different from Link, we have to gut the power sequencing task to do nothing.
For bringup and test, we'll just manually set and get the GPIOs until we
know exactly what we need to do.
This is where the fun starts...
BUG=chrome-os-partner:18825
BRANCH=slippy
TEST=manual
Built everything, Link still works.
Change-Id: Ic1ce1d4085298f49dd98d99e81e04835eca5f11c
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50004
I'll still need to decide what to do differently for Slippy, but for now
let's just identify the places where there will likely be a difference.
BUG=chrome-os-partner:18825
BRANCH=slippy
TEST=manual
Link still works.
Change-Id: I950f0e5356ccf9838f2140d853122235f884e34f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49931
Also renaming to avoid confusion as to what's being charged.
BUG=chrome-os-partner:18825
BRANCH=slippy
TEST=manual
Build everything, Link still works.
Change-Id: I4205a1210c7dfe57cfbbdd740970ef57e6a011b8
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49775
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The state REINIT in TPS65090 charge state machine is more like IDLE0
state in charge_state.h. Rename it so that it's less confusing and
easier to merge the two state machines in the future. Also move the
state name definition to the header file.
BUG=chrome-os-partner:18914
TEST=Boot Spring
BRANCH=None
Change-Id: I116438fedc46ff188dfb6a3964795715b5af4d1f
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49732
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This eliminates a per-second hook and removes a duplicated ADC read per
second. Also, TSU6721 is now reset after every detachment. This way, we
don't suffer from TSU6721 dirty state (most commonly seen after OTG
dongle detached.)
BUG=chrome-os-partner:17928
TEST=1. Test plugging/unplugging video dongle.
2. Test Toad cable mode switching.
3. Test charging with 200K charger.
BRANCH=spring
Change-Id: Ic035b7332e07ca385d766c735ce39efd31e46034
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49578
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The voltage rails, inputs, and sequencing is completely different. Easiest
to just handle it separately for each chipset.
BUG=chrome-os-partner:18825
BRANCH=slippy
TEST=manual
Built Link, still works.
Change-Id: Ibf26ef47cdf2284b7bfb3a2e5ccfb6841aba5ac6
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49559
Reviewed-by: Randall Spangler <rspangler@chromium.org>
STM32L doesn't need the DMA-based workarounds needed by STM32F, since
the STM32L I2C block isn't broken. DMA adds a lot of code overhead
when transferring 2-3 bytes, and is implemented differently on STM32F
vs STM32L so it doesn't even work on STM32L
Add a simple polled I2C implementation for STM32L. This is not the
final implementation, which will use interrupts, but for now it works,
unlike the DMA-based version.
BUG=chrome-os-partner:18969
BRANCH=none
TEST=i2cscan on pit finds a device at 0x90
Change-Id: Ie2a6c9ac6f62b7fd3c35e313b4015e080d9f937a
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49555
With a Toad cable, the user can access the EC serial console through the
micro-B connector.
We probably need to de-activate the input on the EC serial console when
the Write-Protect is on, since we have fairly "powerful" commands on the
EC command-line.
Add a new CONFIG_CONSOLE_RESTRICTED_INPUT on platforms with externally
accessible EC serial port.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=spring
BUG=chrome-os-partner:18716
TEST=on Spring with CONFIG_CONSOLE_RESTRICTED_INPUT set, try with and without
write-protect, use successfully the EC console in the former case, and see
"Console is DISABLED" in the latter case.
Change-Id: Ic9646d5468183f4d8f94b5e5e1d2a727941d7bbe
Reviewed-on: https://gerrit.chromium.org/gerrit/49537
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Also moves the handy i2cscan command to i2c_common. The
platform-dependent interface is now i2c_xfer().
Still more to do in follow-up CLs; for example, i2c_read_string() has
platform-dependent implementation, and the i2c/i2cread console
commands aren't common yet.
BUG=chrome-os-partner:18969
BRANCH=none
TEST=i2cscan on link, spring
Change-Id: Ia53d57beaa157bece293a4262257e20b4107589e
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49492
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit-Queue: Daniel Erat <derat@chromium.org>
Commit-Queue: Simon Glass <sjg@chromium.org>
When battery flags TERMINATE_CHARGE or OVER_CHARGED alarm, we should
treat them as a signal of battery fully charged.
BUG=chrome-os-partner:18914
TEST=On Spring:
1. Plug in adapter when battery if full, see green LED.
2. Plug in adapter when battery is not full, see yellow LED.
BRANCH=spring
Change-Id: Ica414a0e1667b8f30a0cc9a5d66dba1b119a59ba
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49456
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Should use CPRINTF("[%T...\n]") so the messages are timestamped; this
is really helpful to see when things are going wrong.
No functional changes; just changing debug output.
BUG=none
BRANCH=none
TEST=build pit and spring; see prettier debug output
Change-Id: I9c658385b836a184a3ebb84856b844cbfc3224a7
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49551
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes pmu_init() failing on pit, where the charger task isn't
enabled yet (and thus the charger interrupt is NULL - which can't be
enabled).
BUG=chrome-os-partner:18657
BRANCH=none
TEST=build all platforms; on pit, check that pmu_init() no longer fails
Change-Id: I191bbaeb4df10241e3508ccf7ef5ea83f42c5697
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49550
Reviewed-by: Simon Glass <sjg@chromium.org>
Two states were added, but the descriptions weren't. This caused a crash.
BUG=chrome-os-partner:18914
TEST=boot spring with no battery, wait a few secs; shouldn't crash
BRANCH=spring
Change-Id: I10f9280232259a1f467ea3b02f3b1b61cee57471
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49391
We are moving video power from VFET2 to VFET4. To support old boards, we
need to enable both of them. When new boards are in place, we can then
drop VFET2.
BUG=chrome-os-partner:18186
TEST=Build spring
BRANCH=spring
Change-Id: If0cbc1ac49affc1e3c7ec9650a661f80be826f97
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49431
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Sadly, the existence of fans may not always imply the existence of keyboard
backlights.
BUG=chrome-os-partner:18825
BRANCH=slippy
TEST=manual
Use the Link EC console to make sure that both functions still behave.
faninfo
fanset 4400
faninfo
fanset 9999
faninfo
autofan
faninfo
fanduty 50
faninfo
fanduty 100
faninfo
autofan
kblight 0
kblight 100
kblight 50
kbligth 100
Change-Id: I2e07cd46c21bce2d0d4162275a8ea6ae40135e96
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49355
It will soon have cross-platform code moved to it.
This CL just does the renaming; no functional changes.
BUG=chrome-os-partner:18969
BRANCH=none
TEST=build spring,link
Change-Id: I8cc475f9dd1422a0a9c586c93eb0d7aaf21a001d
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49359
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
I2C communication doesn't work on pit yet, so the charger task is
spewing errors to the console. This change allows the task to be
disabled cleanly on pit, and has no effect on other platforms.
BUG=chrome-os-partner:18657
BRANCH=none
TEST=build all platforms and see that charger task is still compiled
everywhere but pit
Change-Id: I788e817d5630fb1a28694819f4ef9948a503a744
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49344
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
No code changes; this is just moving the irq to the module which
actually handles it. This makes it simpler to disable the charger
task separately from the PMU module.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build pit, spring
Change-Id: Ife44a17f69bf21aa000d162318a459cea6fdf661
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49334
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This includes two situations:
1. When charge state machine is still trying to decide the next state.
2. When we are waiting for acceptable condition to start charging.
For now, we show yellow for both.
BUG=chrome-os-partner:18914
TEST=none
BRANCH=spring
Change-Id: I5dd97c735a1ecfee29d506452695014c85d2da0b
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49327
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Currently INIT state can mean different things. This change introduces
two new states to demultiplex INIT. Now, REINIT means charge state
machine is deciding the next state. BAD_COND means it's waiting for
acceptable charging condition. Note that the three states are doing the
same thing so there is no functional change.
BUG=chrome-os-partner:18914
TEST=none
BRANCH=spring
CQ-DEPEND=CL:49327
Change-Id: Ia783e76cf27e28103ef44fe7b8a43674dadccc54
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49326
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The power button code is platform-independent. This change splits the
code out of the LM4 switch.c module so that a subseqent change to
STM32 platforms can start using it.
BUG=chrome-os-partner:18945
BRANCH=none
TEST=manual
1. Power+refresh+esc goes to recovery mode,
2. Press power button at recovery screen turns off.
3. With system off, power button turns system on.
4. Press power button for a second; screen locks.
5. Press power button while typing; blocks keystrokes while it's pressed.
6. Hold power button down for 8 sec; system forced to shutdown.
7. From EC console, with system on:
hostevent clear
hostevent -> event 0x04 is clear
press power button
hostevent -> event 0x04 is set
8. From EC console, with system off:
powerbtn -> system turns on
powerbtn 5000 -> system turns off, just like power button was held for 5 sec
Change-Id: If2a9b02514a201e1d03c857d128e2ccab51a16ef
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49217
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This will allow debugging until the I2C passthru command is supported,
and should be removed once it is supported.
BUG=chrome-os-partner:18778
BRANCH=pit
TEST=build pit; can't test until we have boards
Change-Id: I6285e76763a5f3bfd759161115d4905697b56e6c
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49096
Reviewed-by: Doug Anderson <dianders@chromium.org>
CONFIG_ macros should be set directly. Expanding the task names in the same
way made it difficult to tell what was a configuration choice and what was
due to changes in ec.tasklist
BUG=chrome-os-partner:18343
TEST=build all, run link
BRANCH=none
Change-Id: Ib82e34f974238ee2dd216f33b701b6f4c6a4f1f1
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49098
Reviewed-by: Randall Spangler <rspangler@chromium.org>
apreset and apshutdown are now the same across all platforms.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms; make sure 'apreset warm', 'apreset cold', and
'apshutdown' work.
Change-Id: I4ace1ab2bbda4d400528039ad5f84da63c9c7d0e
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48942
Previously, we sometimes saw battery LED went off when going into or out
of battery assist mode. This CL adds a state machine to stabilize
battery LED. By controlling the state of lighting engine, the
tranisition from/to battery assist mode is seamless now.
BUG=chrome-os-partner:18844
TEST=On spring, check:
1. LED doesn't go off when going into battery assist mode.
2. LED doesn't suddenly change brightness when coming out of
battery assist mode.
3. LED goes red after few seconds when battery is not present.
4. LED goes green when battery is charged.
BRANCH=spring
Signed-off-by: Vic Yang <victoryang@chromium.org>
Change-Id: I3286b54a76edd77c65033ec3bbf0d81d916f7be0
Reviewed-on: https://gerrit.chromium.org/gerrit/48875
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Vic Yang <victoryang@chromium.org>
Tested-by: Vic Yang <victoryang@chromium.org>
STM32-based platforms now use the same lid debouncing code as
LM4-based platforms, generate lid-open / lid-closed events, and
trigger lid-change hooks.
This is needed for disabling keyboard scanning when the lid is closed,
as well as future changes to mask off wake events when the lid is
closed.
BUG=chrome-os-partner:18896
BRANCH=spring
TEST=build all platforms; check that spring boots when lid is opened
Change-Id: I09a6e91119c3739297fe49b7eacac6efda988284
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48924
Reviewed-by: Vic Yang <victoryang@chromium.org>
By default it's not, but if you #define CONFIG_CUSTOM_KEYSCAN, you can add
your own settings in board.c
BUG=chrome-os-partner:18343
TEST=build link, bds
BRANCH=none
Change-Id: I2a9dd48fd7f4610bc39dcc59e59a3fedec539e28
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48994
Reviewed-by: Randall Spangler <rspangler@chromium.org>
