For oak, set a different list of task (no als, no accel) for compiling
revision 4 or less. Fix GPIO include issue.
BUG=chrome-os-partner:59423,chrome-os-partner:59084
TEST=compile for oak with board 4 and 5, tested on Reef.
BRANCH=kevin,reef
Change-Id: I09051a69cbad6d477a7b3bf9907f4c5c144b5136
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/424220
Reviewed-by: Randall Spangler <rspangler@chromium.org>
If battery is not present, input current is set to PD_MAX_CURRENT_MA.
If the input power set is greater than the maximum allowed system power,
system might get damaged. Hence, limit the input current to meet maximum
allowed input system power.
BUG=chrome-os-partner:58498
BRANCH=none
TEST=Manually tested on Reef. Removed the battery & using 'charger'
console command observed the following.
With Zinger charger at 20V - Input current is set to 2.25A
With Type-C & other chargers - Input current is set to 3A
Change-Id: Ife8686f322e095aa74b740a7c469bfe87107fb9a
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/397865
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
charge_manager may request a charge current limit less than the
capability of the supply in certain cases (eg. during PD voltage
transition, to make an effort to comply with reduced load spec).
Depending on the battery / system state, setting a reduced charge
current limit may result in brownout.
Pass the uncapped / max negotiated current to board_set_charge_limit()
so that boards may use it instead of the requested limit in such
circumstances.
BUG=chrome-os-partner:56139
BRANCH=gru
TEST=Manual on kevin with subsequent commit, boot system with zinger +
low-charge battery, verify devices powers up to OS without brownout.
Change-Id: I2b8e0d44edcf57ffe4ee0fdec1a1ed35c6becbbd
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/383732
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
When the charger is detached, the host event would sometimes be
sent before the charge info was updated, resulting in the host
thinking that the charger was still connected.
BUG=chrome-os-partner:55584
BRANCH=none
TEST=Connected charger to kevin 15 times and verified that the
icon was removed in 2-seconds or less.
Change-Id: I1a4e4e0f7cc23010210570fc261da8308d8e8070
Reviewed-on: https://chromium-review.googlesource.com/367809
Commit-Ready: Wonjoon Lee <woojoo.lee@samsung.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Since pretty much always, we've declared console commands to take
a "longhelp" argument with detailed explanations of what the
command does. But since almost as long, we've never actually used
that argument for anything - we just silently throw it away in
the macro. There's only one command (usbchargemode) that even
thinks it defines that argument.
We're never going to use this, let's just get rid of it.
BUG=none
BRANCH=none
CQ-DEPEND=CL:*279060
CQ-DEPEND=CL:*279158
CQ-DEPEND=CL:*279037
TEST=make buildall; tested on Cr50 hardware
Everything builds. Since we never used this arg anyway, there had
better not be any difference in the result.
Change-Id: Id3f71a53d02e3dc625cfcc12aa71ecb50e35eb9f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/374163
Reviewed-by: Myles Watson <mylesgw@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This feature is inconsistent. Not all boards have such a symlink
(for a obvious reason).
This feature is fragile. It's most likely not tested and going to be
broken if not already. Developers won't like it if they have to test
two different ways to build boards before submitting patches.
This feature is not necessary. If you build EC in the standard way
(e.g. make BOARD=samus), these symlinks are not needed.
This feature is wasteful. Extra disk spaces are used and extra lines
are added to Makefile (increasing code complexity slightly).
BUG=chromium:626776
BRANCH=none
TEST=make buildall
Change-Id: Id5444284d773cb0e9225f39abd877441b8f61440
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/359321
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Not everything with a temperature sensor uses thermal throttling. This
change modifies the conditional build to enable building temp sensor
source without thermal throttling.
BUG=none
BRANCH=none
TEST=make buildall -j
Change-Id: I8c0753f12899e9f203c04477ae520bcda40d5fd8
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/356484
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Previously CONFIG_USB_PD_TCPM_VBUS had two uses which were independent:
- When operating as a TCPC, it indicated that the VBUS level should be
tracked (through GPIO inputs) and sent to the external TCPM when
appropriate.
- When operating as a TCPM, it indicated that the VBUS level should be
obtained by querying the TCPC.
These two independent uses have been split into
CONFIG_USB_PD_TCPC_TRACK_VBUS and CONFIG_USB_PD_VBUS_DETECT_TCPC, which
sould be more clear.
In addition, CONFIG_USB_PD_VBUS_DETECT_* CONFIGs have been added for
other means of VBUS detection.
BUG=chromium:616580
BRANCH=None
TEST=Verify kevin continues to boot + charge.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I936821481d6577e17e3e9c61ff97c037574d6923
Reviewed-on: https://chromium-review.googlesource.com/348950
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Previously the maximum number of deferred routines was specified by the
the default maximum number of deferred routines you had to override
this, and if you wanted fewer, you still payed the price of having the
defer_until array statically allocated to be the maximum size.
This change removes that define and instead creates the RAM state of
the deferred routine (the time to wait until to call the deferred) when
the deferred is declared.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
manually test on discovery-stm32f072
Change-Id: Id3db84ee1795226b7818c57f68c1f637567831dc
Reviewed-on: https://chromium-review.googlesource.com/335597
Commit-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Previously calls to hook_call_deferred were passed the function to call,
which was then looked up in the .rodata.deferred section with a linear
search. This linear search can be replaced with a subtract by passing
the pointer to the deferred_data object created when DECLARE_DEFERRED
was invoked.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
CQ-DEPEND=CL:*255812
TEST=make buildall -j
Change-Id: I951dd1541302875b102dd086154cf05591694440
Reviewed-on: https://chromium-review.googlesource.com/334315
Commit-Ready: Bill Richardson <wfrichar@chromium.org>
Tested-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
After a charger is attached, we may set a charge limit based upon BC1.2
or USB-C Rp before PD negotiation completes. Therefore, allow 2 seconds
for all negotiation to complete. Previously this behavior was implicit
when using SW charge ramp.
BUG=chrome-os-partner:51280
BRANCH=glados
TEST=Manual on chell. Insert stock charger, verify that it is detected
as TYPE_UNKNOWN until timeout.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I52f02de46fa92b66a9fbaddb94a062310688f028
Reviewed-on: https://chromium-review.googlesource.com/334312
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
With commit e9883124ff, a GPIO_INT macro was added. That change
also required that all instances of GPIO_INT in a board's
gpio.inc file come before any GPIO macros, or the interrupt
handler wouldn't work properly.
This CL just adds a warning comment about requirement to all
gpio.inc files.
BUG=chromium:471331
BRANCH=none
TEST=make buildall, test image on Cr50
This is a change to comments only. There is no new behavior to
verify, although I did run try out one new image just to be sure
nothing stupid happened.
Change-Id: I83f7819929a53bce3a8bae04d15b3ee3bda11738
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/329334
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Previously these were often done in board.c files, which made it
impossible to include the gpio.inc anywhere else. As part of
refactoring the GPIO code we now need to be able to include gpio.inc
from common/gpio.c. Moving these defines into gpio.inc makes them
available wherever gpio.inc is included.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Change-Id: I28e7b5a1d40b113ae824b18f020b2d1e51e0c08a
Reviewed-on: https://chromium-review.googlesource.com/328822
Commit-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
this is to move the existing code from chipset level to board level
since PseudoG3 is a board feature that required specific hardware.
BUG=none
BRANCH=glados
TEST=use hibernate command to enter PseudoG3
Change-Id: I309ef89e0ff7057ce46c634baa9791731a771984
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/327677
Reviewed-by: Shawn N <shawnn@chromium.org>
For TCPMs with an off chip TCPC, PD MCU host event status can be handled
in a common way. When a status flag is updated (ex. from
charge_manager), notify the AP through the host event, and save the
status flag for later retrieval.
BUG=chrome-os-partner:49124
BRANCH=None
TEST=Verify `cat /sys/class/power_supply/CROS_USB_PD_CHARGER1/online` on
chell reflects the actual online status of the charger. Also verify UI
charge icon tracks the online status correctly.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I63bc70205627474590e38ffd282faedaea3bcc66
Reviewed-on: https://chromium-review.googlesource.com/320796
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Rather than having various PWM module groups initialized from various
HOOK_INIT functions, group them all into a single module and initialize
them all from a common function in pwm.c.
BUG=chromium:563708
TEST=Manual on samus / samus_pd (with CONFIG_ADC enabled). Verify that
samus fan + KB backlight control is functional and samus_pd correctly
sets PWM output.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I9f9b09bfa544cd9bc6b7a867e77757dff0505941
Reviewed-on: https://chromium-review.googlesource.com/314882
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
To ease finer calculation of ec rate change units from
ms to us.
BRANCH=smaug
BUG=b:24367625
TEST=compile
Change-Id: I52057c8ca1b1180a64b58d1ba0af9ec53f40b026
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/312984
Change ADC channels on mec1322 boards to use scaling based on ADC
reference voltage of 3.0V instead of 3.3V. Also, setup the scaling
for AMON_BMON which reads the adapter input current or battery
current in mA.
BUG=none
BRANCH=none
TEST=tested on glados. use adc console command and verify it
roughly matches twinkie voltage and current.
Change-Id: Id6ed72012ebb1c23cf98a14ee6c156ec0f5fb586
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/311302
Reviewed-by: Shawn N <shawnn@chromium.org>
Add a new configuration struct tcpc_config_t that initially defines the
i2c host port and i2c slave address of all TCPCs present on the board.
This will allow us to create boards with multiple TCPCs on different i2c
ports, with arbitrary i2c slave addresses.
BUG=chromium:551078
TEST=Manual on glados. Verify PD communication / charging is still
functional on both PD ports.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I9b2bde85d7f1642e8727c052e064371be7967619
Reviewed-on: https://chromium-review.googlesource.com/311000
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Some chips previously defined CONFIG_I2C and others didn't. Standardize
the usage by removing CONFIG_I2C from all config_chip files and force it
to be defined at the board level. Also, make boards define
CONFIG_I2C_MASTER and/or CONFIG_I2C_SLAVE based on the I2C interfaces
they will use - this will assist with some later cleanup.
BUG=chromium:550206
TEST=`make buildall -j`
BRANCH=None
Change-Id: I2f0970e494ea49611abc315587c7c9aa0bc2d14a
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/310070
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Change battery and variable sink capabilities for all boards
to account for +/-5% voltage inaccuracy.
BUG=none
BRANCH=none
TEST=test glados with third party variable power supply and make
sure it see's our sink capabilities as 4.75V-21V.
Change-Id: I2481ccbe6c47bfed1a6b8b237329e70bd0f8e4ac
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/308237
Reviewed-by: Todd Broch <tbroch@chromium.org>
The port 80 task just polls every 1ms until disabled when the system
goes into suspend. Therefore, this commit configures a 1ms timer
interrupt that will be used for the port 80 writes instead of using an
entire task. This saves task stack space as well as context switches.
BUG=chrome-os-partner:46062
BUG=chrome-os-partner:46063
BRANCH=None
TEST=Flash GLaDOS and verify using the `port80' console comamnd that
there are bytes in the port80 history.
TEST=make -j buildall tests
Change-Id: I65b48217a638c1f6ae1ac86471f9a98e0ec4533a
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/305591
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Remove duplicate code for checking request message, but keep
a board specific check of the request message for custom checks
needed on zinger and plankton.
BUG=chrome-os-partner:42490
BRANCH=none
TEST=make -j buildall. run on samus and connect a hoho, make
sure we successfully negotiate a contract.
Change-Id: I7398953a158d340e3e113f5a816b55445a857711
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/305374
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Set USB communications capable flag in source/sink
capabilities PDO on boards that support USB. This
signals to other side that we are capable of
communication over D+/D- or SS Tx/Rx.
BUG=chrome-os-partner:34982
BRANCH=samus,smaug
TEST=load on samus, use twinkie to sniff traffic,
verify that USB comms capable bit is set in source
cap packet
Change-Id: I0f49cf19eb141512298c3439a4708c53101d674f
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/300637
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add config option to use the old accelerometer reference frame,
which is used on samus and products using 3.14 or earlier kernel.
This fixes samus so that the lid angle calculation is correct
again.
This also moves the accel_orientation structure out of the board
directory and into common code, since it purely is a function of
the reference frame being used.
BUG=chrome-os-partner:43494
BRANCH=none
TEST=test on samus, verify lid angle calculation is correct once
again. also, enable the motion_lid test and verify that it passes.
Change-Id: I948a74a71964b54c68be66e828a030ddd0418947
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/300510
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Since there is no more concept of a flash region belonging only to the
EC, we only need one FLASH_SIZE config, which represents the actual
physical size of flash.
BRANCH=None
BUG=chrome-os-partner:23796
TEST=With entire patch series, on both Samus and Glados:
- Verify 'version' EC console command is correct
- Verify 'flashrom -p ec -r read.bin' reads back EC image
- Verify software sync correctly flashes both EC and PD RW images
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I18a34a943e02c8a029f330f213a8634a2ca418b6
Reviewed-on: https://chromium-review.googlesource.com/297824
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This commit adds a new basic driver for the Kionix KX022 Accelerometer.
Currently, the driver is capable of reading the sensor data and
manipulating its ODR, resolution, and range.
This sensor also has integrated support for Directional
Tap/Double-Tap(TM), however that functionality is not yet implemented in
the driver.
Lastly, since this accelerometer is very similar to the previous KXCJ9,
this commit tries to combine the drivers.
Note, the variant of the Kionix accelerometer MUST be specified in the
private data structure.
BUG=chrome-os-partner:43494
BRANCH=None
TEST=Build GLaDOS EC with driver enabled and verify that valid
accelerometer data is read, and that range, resolution, and odr can all
be modified.
TEST=Build samus EC image and verify that the lid still
works. Additionally, verify that I can change the odr, rate, and
resolution.
TEST=make buildall tests
Change-Id: I238ff1dc13f5342a93f8f701a0da85c52f25d214
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/299013
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
If the ALS is not enabled in S3/S5 states then it will generate
errors when trying to read so should be gated.
This could be done with a check for chipset_state or adding a
new CONFIG_ALS_POWER_GPIO to check. However the ALS is also not
needed when the host is in S3/S5 yet the task continues to run
in the background every 1 second.
This commit adds a new task enable/disable hook to disable the
task when the system is suspended and enable the task when it
is resumed.
In order to fit this new task in glados the als console command
is guarded by a new config option. Since this is not a very
frequently used/needed console command it is disabled by default.
And finally the kunimitsu and strago boards try to enable ALS
but they never actually enabled the ALS task so this new code was
failing to build because TASK_ID_ALS did not exist. Also samus
was enabling it but as TASK_NOTEST so tests will fail, though
they are disabled globally on samus.
BUG=chrome-os-partner:43493
BRANCH=none
TEST=enable ALS on glados and successfully build and use it,
also successfully build EC and tests for kunimitsu, strago,
and samus which are the other boards that use the ALS task.
Change-Id: I192940d7f306a1663c7cb789c313151bbb5f2b90
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/298156
Reviewed-by: Shawn N <shawnn@chromium.org>
Use new config structure.
Remove pre-init when sensors are shutdown in S3 on strago:
motion_sense is not setting ODR to 0 inconditionally when
sensors are not active.
active_mask now means state (S0, S3, S5) where sensors are powered on.
When sensor is powered but unused, EC can use the config array to set
the polling and ODR to 0.
BUG=chromium:513458
TEST=On Cyan, verify the sensors are working in S0. In S3, check the
motion_sense task is idle (now sensor to probe). Check the task
comes back on resume.
BRANCH=cyan,strago
Change-Id: Ib3d118b7139f94755fef4cb73fc1274e9e2f2826
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/295781
Reviewed-by: Sheng-liang Song <ssl@chromium.org>
Move common USB charger code out of board directory including
setting VBUS supplier when VBUS changes, and initializing BC1.2
supplier types on init.
This also enables re-enabling of Pericom BC1.2 detection interrupts
when VBUS is changed on all boards that use USB_CHG task.
BUG=chrome-os-partner:42292
BRANCH=none
TEST=make -j buildall. Tested on glados and samus by plugging in
a few different chargers and making sure we charge.
Change-Id: Ib102fbf7a6aace998e6fcb6d35f3c97e5f03f5c2
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/290453
Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Rong Chang <rongchang@chromium.org>
Configure boards whose chipset cannot be a USB UFP to disconnect
USB lanes when the data role is UFP.
BUG=none
BRANCH=strago
TEST=make -j buildall. tested on glados by adding ccprintf to
usb_charger_set_switches(). verified when we are DFP, USB 2
switches are connected and when we are UFP, they are disconnected.
Change-Id: Ic8c817a0cc21b56ee67239e8cc81d5cbbda8d4de
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/290422
Reviewed-by: Shawn N <shawnn@chromium.org>
Allow more than one SPI master.
Add CONFIG variables to address the system SPI flash.
To have SPI master ports, spi_ports array must be defined.
BRANCH=smaug
TEST=compile
BUG=chrome-os-partner:42304
Change-Id: Id43869f648965c1582b7be1c7fb3a38f175fda95
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/288512
Commit-Queue: David James <davidjames@chromium.org>
Enable Try.Src for Glados, Kunimitsu, Strago, and Oak so that they
default to sourcing power when connecting to other dual-role
devices.
BUG=none
BRANCH=strago
TEST=make -j buildall
Tested on glados by plugging in charger, hoho, and another
dual-role device and making sure we resolve roles appropriately.
Change-Id: I9393e30b35620eeda3ef1ef56366a97e59ba8054
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/288247
Reviewed-by: Shawn N <shawnn@chromium.org>
