Added config option CONFIG_USB_PD_TX_USES_SPI_MASTER which switches
to use SPI master for PD transmit. The advantage of SPI master mode
is at the end of the tranmission, we don't have to send any dummy 0
bits. When the option is set, the CPU_CLOCK must be set to 38.4MHz,
so that the SPI master can generate the correct clock frequency.
BUG=chrome-os-partner:28309
BRANCH=none
TEST=Tested by connecting two fruitpies together across CC1. One
fruitpie has been modified such that the MISO and MOSI lines are
swapped and is running PD TX in SPI master mode with 38.4MHz clock,
while the other is running PD TX in SPI slave mode. On EC console
ran pd charger on one board and pd dev on other board. Verified
that communication works with no errors. Ran for 10 minutes in each
configuration.
Change-Id: Ib24030d34d95d59f4ac6c2dae98bf7adda1ada01
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/197215
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Also adds 'battparam' console command.
BUG=chrome-os-partner:25145
BRANCH=ToT
TEST=Run 'ectool batteryparam set 0 0x1234'
'ectool batteryparam get 0'
and on the console:
'battparam 0'
'battparam 0 0x1234'
on a board that implements parameter 0.
Change-Id: I9cc54d001631f53dd39ae64cfdeececaa1747181
Original-Change-Id: Ib2812f57f2484309d613b23dab12ad43e0417bd2
Signed-off-by: Dave Parker <dparker@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/195824
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/197162
So that host and EC commands will be defined in common/battery.c.
The board-specific battery.c can focus on the proprietary method.
BUG=chrome-os-partner:28248
BRANCH=tot,nyan
TEST=make buildall runtest
Tested "cutoff" in EC console on big.
Change-Id: I213c0d601d0241c8dea309d6ac60c72452d2d100
Signed-off-by: Louis Yung-Chieh Lo <yjlou@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/196621
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Added a sub-command to the motionsense host command (0x2b) for getting/setting
the lid angle at which the keyboard is disabled as a wake source in S3. The
value can be anywhere from 0 to 360 degrees, default set to 180. Note, this
only takes affect for boards that have CONFIG_LID_ANGLE_KEY_SCAN defined.
Modified ectool motionsense command to use new host sub-command.
Also modified the lid angle measurement in the EC to be in the range [0, 360],
instead of [-180, 180], and changed casting of lid angle as an int to round
to nearest.
BUG=none
BRANCH=rambi
TEST=Tested on a glimmer:
Using default keyboard disable lid angle of 180, made sure that when lid
angle is past 180, key presses do not wake system, and when lid angle is
less than 180, key presses do wake up system.
Used ectool motionsense kb_wake to set the keyboard disable lid angle to 0.
Made sure that keyboard never wakes up the system. Set keyboard disable lid
angle to 360 and made sure that the keyboard always wakes up the system.
Change-Id: I437164c6e38c29169ef6e20e86c9cf2a1c78f86e
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/193663
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/194172
This is a complete rewrite of the charge_state task used by x86 platforms.
Rather than having a bunch of state-specific functions, each with their own
error handling and special cases, this is organized like so:
Forever:
1. Read everything we can from the battery and charger.
2. Figure out what we'd like to do (including error handling).
3. Allow for customization to override that.
4. Do it.
Things I need to file bugs for are marked with "TODO(wfrichar)". I'll file
the bugs after this CL goes in, so that they'll have something relevant to
refer to.
BUG=chrome-os-partner:20881
BRANCH=ToT
TEST=manual
make buildall -j
Try it on Samus, watch it charge from nearly empty to full, both with and
without fastcharge enabled.
Also undefine CONFIG_BATTERY_PRESENT_CUSTOM, plug and unplug the battery to
be sure the trickle charging logic is correct when it can't tell if the
battery is present.
Change-Id: I3935cd3b87f322eb52178f8a675a886c16b75d58
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/191767
Reviewed-by: Randall Spangler <rspangler@chromium.org>
add support for CRC-32, it's using the USB variant for the constants and
bit ordering (same polynom as Ethernet).
This code is using an (evil) "stateful" design to be compatible with the
hardware CRC controller : you should NOT do concurrent accesses without
external locking (but it's good enough and ligthweight for current
usage)
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=run interoperability testing against other 3rd parties USB
implementations.
Change-Id: I1a07b2c4e2e71e15f9d257611652061bcfb0de9c
Reviewed-on: https://chromium-review.googlesource.com/189865
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Add support TI BQ24773 1S/2S/3S NVDC battery charger.
This is not a "Smart Battery" compliant charger IC, it should and cannot
use the sbc_ helpers.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=on FruitPie, run "charger" command on the EC console,
add the charger task and see the battery charging.
Change-Id: I6f470184f0ce424a05007e493d802dcdb2156477
Reviewed-on: https://chromium-review.googlesource.com/191212
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
The charger driver code has no dependency on the charger task,
we do not need to force the de-activation when the charger task is not
running.
This allow to debug new charger code without the task acting in
background and should not have any drawback.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=make buildall
and run "charger" command on Fruitpie without the charger task.
Change-Id: I49a4885a2abf0e5d9e652e037941b1c4672beb7a
Reviewed-on: https://chromium-review.googlesource.com/191211
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Added ability to disable the keyboard to wake from suspend when the lid
is outside a certain angle range. This has been added to glimmer by
defining CONFIG_LID_ANGLE_KEY_SCAN in its board.h.
Also modified the lid angle calculation to include a reliability
flag which can be used to tell when the hinge aligns too closely
with gravity and the lid angle value is unreliable.
BUG=none
BRANCH=rambi
TEST=Tested on a glimmer:
In S3, verified that when the lid is open past ~180 deg, the keyboard
does not wake the machine. Also verified that if you align hinge with
gravity, the keyboard enabled/disabled status remains the same (since
we can't actually trust the lid angle value).
Change-Id: I45b2c7c3c4bbcae61d3a0f8b5baa461ab8dabfb0
Original-Change-Id: If1a1592d259902d38941936961854b81b3a75b95
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/190061
Reviewed-on: https://chromium-review.googlesource.com/191612
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Adding in support for accelerometer interrupt for use currently
in clapper and glimmer. This is disabled by default and can
be enabled with CONFIG_ACCEL_INTERRUPTS.
BUG=none
BRANCH=rambi
TEST=Manual test on a glimmer using accelint console command.
On console enter:
accelint 0 32
When you tap the lid, it should fire the interrupt and print msg
to console.
accelint 1 32
Tap the base and it will fire another interrupt.
Change-Id: Iaab324945e34d527140399ec4f06efd812a62840
Original-Change-Id: I0329112fdcae3c8adc0ca07e74fef7a591d4b9a1
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/190099
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/191549
This can be helpful when debugging "Imprecise" data bus errors.
BUG=None
BRANCH=None
TEST=Write to a memory-mapped register such as LM4_ADC_ADCISC
for a hardware block that is powered down.
Check the exception trace for a "Precise" error.
Change-Id: Ia246c3661b482e212bb0ce37b9c2d383021de639
Signed-off-by: Dave Parker <dparker@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/191392
Reviewed-by: Randall Spangler <rspangler@chromium.org>
In order to achieve really tiny firmwares, make our runtime (tasks,
hooks, muxed timers, GPIO abstraction ...) optional.
Add 2 new build options for it : CONFIG_COMMON_RUNTIME and
CONFIG_COMMON_GPIO which are enabled by default, and ensure all the
source files are built according to the right configuration variable.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=make buildall
build a minimal board with no runtime.
Change-Id: Icb621cbe0a75b3a320cb53c3267d6e578cd3c32f
Reviewed-on: https://chromium-review.googlesource.com/189403
Reviewed-by: Vic Yang <victoryang@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Making room for a new charge_state implementation.
BRANCH=ToT
BUG=chrome-os-partner:23776
TEST=make buildall -j
No new functionality, just renaming some files.
Change-Id: I80ce861f09129a518e180cac20d32e867a93cd46
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/190852
Reviewed-by: Randall Spangler <rspangler@chromium.org>
We don't have available GPIO pin for power button as the hibernate
(stand-by) wake-up source. Also, we don't want to do board change.
So, put the EC in a decent infinite loop to pretend the hibernate mode
and wait for particular wake-up event. This should be fine because
the AP is already down before EC hibernates.
BUG=chrome-os-partner:25435
BRANCH=Nyan
TEST=see comment #6 of issue for detailed test steps.
Change-Id: I2cae131789f9ca5808b60d5f2495222ca9016e7c
Signed-off-by: Louis Yung-Chieh Lo <yjlou@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/186061
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Move the CLZ instruction emulation C code to the common directory, so it
can be reused for all CPU cores missing a CLZ instruction (e.g. CortexM0).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=run EC console on STM32F072B Discovery board with Cortex-M0 core,
and pass all available unit-tests on target.
Change-Id: Ief56cac7430fcb0fbced8a8925250c89cbd0bcfc
Reviewed-on: https://chromium-review.googlesource.com/188981
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
The EC had inputs with internal pullups on SUS_STAT#, SUSPWRDNACK, and
SLP_SX#. But we never used those signals for anything. The pullups
cost 1.5 mW power in S3. So, remove those signals and their pullups.
They can be turned back on via CONFIG_CHIPSET_DEBUG.
BUG=chrome-os-partner:25568
BRANCH=rambi
TEST=build with and without CONFIG_CHIPSET_DEBUG. Verify gpioget and
powerindebug show the signals only when it's defined.
Change-Id: I0851243615c91a3aa8aa1b28df70809b578d2e74
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/188389
Reviewed-by: Dave Parker <dparker@chromium.org>
Previously, the AP could only set the current wireless power state.
It couldn't determine what the EC would do in S3, nor could it get the
current wireless power state. Extend the wireless command to do so,
and add an EC console command to aid in debugging.
BUG=chrome-os-partner:25655
BRANCH=rambi
TEST=manual; expected numbers are from EC 'wireless' command
AP off -> 0x0, 0x9
AP on -> 0xd 0x9
AP suspended -> 0x9 0x9
AP on -> 0xd 0x9
ectool wireless 0x1 -> 0x1 0x9
ectool wireless 0xd -> 0xd 0x9
ectool wireless 0 0 0 0 -> 0xd 0x9 (and prints 0xd 0x9 to root shell)
ectool wireless 5 -1 -1 0 -> 0x5 0x9
AP suspended -> 0x1 0x9 (doesn't turn on 0x8, just turns off 0x4)
AP on -> 0xd 0x9
ectool wireless 0 0 0 -1 -> 0xd 0x0
AP suspended -> 0x0 0x0
AP on -> 0xd 0x9
Change-Id: I8ead2d4a4423b51ec4f638bf94c62de98726b25c
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/187273
Added motion sense task to Clapper and Glimmer. This task samples
the accelerometers and calculate a lid angle. Note that as
the machine is rotated towards the hinge angle aligning
with gravity, the lid calculation becomes less trustworthy.
Added a math_util file to hold various mathematical functions
useful for calculating lid angle that may be helpful in other
places.
For each board with accelerometers we need to define some
orientation specific data in board.c. There is a calibration
procedure through the EC console that can be enabled by
defining CONFIG_ACCEL_CALIBRATE. The calibration procedure can
help determine the orientation data required.
For debugging purposes there is a console command to regularly
print to the EC console the accelerometer data and derived lid
angle. The console command can be enabled by defining
CONFIG_CMD_LID_ANGLE.
BUG=none
Original-BUG=chrome-os-partner:24703
BRANCH=rambi
TEST=Ran the calibration procedure on a Glimmer unit, and then
rotated the machine in space. Verified that the lid angle
calculated roughly matched actual lid angle.
Original-Change-Id: I63a5e384b7f6b628b4ea01de49843355fb8d6ebe
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/184783
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Alec Berg <alecaberg@chromium.org>
(cherry picked from commit efb07945a5159fa0e7a746c666b2519ebdca9c22)
Conflicts:
board/clapper/board.c
board/clapper/ec.tasklist
board/glimmer/board.c
board/glimmer/ec.tasklist
Change-Id: Ibc492ef5c11e7084e87f01338c4d7775f9a08c18
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/187433
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Added accelerometer driver for kxcj9 accelerometers. Currently
the accelerometers aren't being used by anything, but there are
console commands, accelwrite and accelread, to perform transactions.
BUG=none
BRANCH=rambi
TEST=Used EC console commands to test that accelerometers respond
and data looks reasonable.
Original-Change-Id: I6ddcf04ec278adeacb148c19b10c3c296b467954
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/184693
Reviewed-by: Randall Spangler <rspangler@chromium.org>
(cherry picked from commit 5e1d2052b034b2400b98b2126243e01397a2ce56)
Conflicts:
board/clapper/board.c
board/clapper/board.h
board/glimmer/board.c
board/glimmer/board.h
Change-Id: If8744ddc3273fc08e29830adfd068dc302dd120a
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/187432
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This is experimental for now; the capsense chip simply reports its buttons
as the number keys on the keyboard (1-8).
BUG=chrome-os-partner:23382
BRANCH=samus,ToT
TEST=manual
To test, you'll need a reworked and correctly programmed capsense module.
Boot the system, and switch to VT2. Touch the capsense bar and you'll see
the input appear on the console as though you were typing numbers.
Note that the capsense hardware is still buggy. Refer to the bug for
workarounds.
Change-Id: I4c3a8b70b8197ffd538c38c59c9336383365afa7
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/185434
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
BUG=chrome-os-partner:24912
BRANCH=baytrail
TEST=Manual. Enable CONFIG_POWER_BUTTON_IGNORE_LID
on a device, boot it, and go into dock mode with
external monitor attached. Fake-close the lid with a
magnet or servo. Verify the power button still sends
press/release events to the host with evtest.
Change-Id: Idb05375eee0743a8a2c459070854c03fe3afe894
Signed-off-by: Dave Parker <dparker@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/184493
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This should reduce EC power consumption in S3 and S5.
BUG=chrome-os-partner:25377
BRANCH=baytrail
TEST=make sure jtag is not active (not running openocd via servo)
boot system; suspend system
wait 60 seconds; should see "Disabling console in deep sleep"
type on console; should still allow typing
wait 60 seconds; press spacebar; should still resume from suspend
Change-Id: I47e33e158c1b90077f944a6af4374f39efa68d94
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/184165
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Previously, the 5V rail was disabled unconditionally in the S0->S3
transition. Now, the rail is left powered if one or both of the USB
ports are powered.
BUG=chrome-os-partner:25178
BRANCH=rambi
TEST=Modify the OS to leave USB ports powered in S3. Then suspend. On
the EC console, 'gpioget pp5000_en' should be 1.
Change-Id: I3c73f3fe228e940317c0da7330f117c7ab0a6d0c
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/183548
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For the better naming for power/common.h, we rename CONFIG_CHIPSET_X86
to CONFIG_POWER_COMMON (no one is actually using it). But keep
CONFIG_CHIPSER_TEGRA for power/build.mk.
BUG=chrome-os-partner:25068
BRANCH=nyan,falco,link,peppy,rambi,samus,squawks
TEST=build only
Change-Id: Ibf1a4c24088dfddac39b38a95b3b887c195152d5
Signed-off-by: Yung-Chieh Lo <yjlou@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/182732
Some WiFi devices do not tolerate losing power in suspend
and will not function properly after resume if they have
lost power.
Enable this on the Rambi device.
BUG=chrome-os-partner:24114
BRANCH=baytrail
TEST=complete mutiple successful suspend/resume cycles on rambi
and ensure that wifi continues to function and not cause a crash.
Change-Id: Id421f3138e429b247bfb3f5ffb92a06c0353bb97
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/183047
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Vboot hash calculation takes ~350 ms during EC boot. Since the hash
task is higher priority than the hook task, this starves all the hooks
during boot.
We could, in theory, fix that simply by swapping the priority of the
hook and hash tasks. But then watchdog detection (in the hook task)
wouldn't detect hangs in the hash task.
A better fix (implemented here) is to convert the hashing operation to
a series of deferred function calls. This gets rid of the hash task
entirely, and allows all pending hooks and other deferred function
calls to take place between each chunk of hashing.
On STM32-based boards, we need to bump up the hook task stack size,
since hashing is called from several layers deep in the hook task
instead of at the top of its own task, but this is still a net win of
several hundred bytes of SRAM.
BUG=chrome-os-partner:24892
BRANCH=rambi
TEST=Boot EC; look for "hash start" and "hash done" debug output.
'taskinfo' shows at least 32 bytes of unused stack for HOOKS task.
'hash ro' runs properly from EC console.
Change-Id: I9e580dc10fc0bc8e44896d84451218ef67578bbe
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/181954
It will be used by all variants of Rambi, so #ifdef BOARD_RAMBI is too
restrictive.
BUG=chrome-os-partner:24864
BRANCH=rambi
TEST=boot rambi 1.5 board; plug in USB mouse
Change-Id: I0ff02077388a6c6621c5746a693dde894cf8ad77
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/181682
Reviewed-by: Alec Berg <alecaberg@chromium.org>
BUG=chrome-os-partner:24455
BRANCH=none
TEST=Manual: Verify that CONIFG_PECI_TJMAX set per-board matches
the value queried over the PECI bus with the restricted
"peciprobe" command.
Change-Id: I8e99a23a66f26d6101e01cc751d0a8ca79686321
Signed-off-by: Dave Parker <dparker@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179682
Reviewed-by: Alec Berg <alecaberg@chromium.org>
This allows local and remote temp values to be added
to a board's list of temp sensors. It also adds a
'tmp432' EC console command to query temps
and set alert thresholds. Fractional degrees are not
supported. DPTF support is not addressed.
BUG=chrome-os-partner:23985
BRANCH=none
TEST=Add tmp432 support to a board with the sensor
then run the 'tmp432' and 'temps' EC console commands.
Signed-off-by: Dave Parker <dparker@chromium.org>
Change-Id: Ifee47cf4d4cf5eedef9ef2bfa2149f183f1d7a7b
Reviewed-on: https://chromium-review.googlesource.com/178688
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Dave Parker <dparker@chromium.org>
Tested-by: Dave Parker <dparker@chromium.org>
Move the non-core dependent code out of core/$(CORE) directory to
common/ directory.
Put all panic printing code in common/panic_output.c
Put timer management code in common/timer.c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:23574
TEST=./util/make_all.sh
use "crash divzero" and "panicinfo" on Link.
Change-Id: Ia4e1ebc74cd53da55fe24f69e96f39f512b9336d
Reviewed-on: https://chromium-review.googlesource.com/178871
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Jeremy Thorpe <jeremyt@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
These boards are unloved and unsupported. They'll never grow up to be
laptops, and hardware is increasingly hard to come by.
Comparable functionality is available in the other, more-loved boards.
Removing these boards speeds up util/make_all.sh by 40%. (If you're
not running that before every upload, you should be...)
BUG=chrome-os-partner:24062
BRANCH=none
TEST=build all remaining platforms and pass unit tests
Change-Id: I4d8a49e4d52d7393471f1b1cbef059c8db4a4f77
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177373
On certain boards it's no feasible to use the SERIRQ
method for generating the kebyboard interrupt. To that
end provide CONFIG_KEYBOARD_IRQ_GPIO option which
specifies the negative edge-triggered gpio for the
keyaboard interrupt.
BUG=chrome-os-partner:23965
BRANCH=None
TEST=Built and booted rambi using this option. Keyboard
works in kernel with interrupts for i8042 device.
Change-Id: I64f7e9530841c184d2a33821126ec446c96bb0f0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177188
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The LPC module has a dedicated control for SCI#.
However, certain situations require a dedicated
GPIO for asserting the SCI# signal.
Introduce CONFIG_SCI_GPIO to meet this requirement.
BUG=chrome-os-partner:24003
BRANCH=None
TEST=Built and booted rambi with dependency change. 'lidclose' and
'lidopen' cause ACPI interrupts.
Change-Id: I34c5f0ba5ff60151972921f251c71d3769a9ef8b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176804
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This adds the driver and a console command to read an Intersil ISL29305
light sensor connected to the EC.
BUG=chrome-os-partner:23380
BRANCH=samus
TEST=manual
Run the "als" command from the EC console, while pointing the sensor in
various directions. It should give higher numbers when facing a light
source. If you get "Error 1", it means the ALS isn't powered.
Change-Id: I855ed64dab7fc60e29126ab3e97669be24dc6a64
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176056
Changes somewhere in the recent past have caused I2C operations to
consume more stack space. The current failure mode is that after some
debug command or infrequent battery operation, the system fails.
Clean up and enable stack overflow detection by default, and add a
debug command (disabled by default) to verify overflow detection
works.
This adds several instructions to each context switch, but it's still
fairly inexpensive, and represents only a few percent increase in the
size of svc_handler(). That's better than silent failures.
BUG=chrome-os-partner:23938
BRANCH=none
TEST=Enable CONFIG_CMD_STACKOVERFLOW, then run the 'stackoverflow' command.
This should cause a stack overflow to be detected in the CONSOLE task.
Change-Id: I9303aee5bd9318f1d92838b399d15fb8f6a2bbf9
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176113
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Temporary fix to the bug in which we miss wake events when in deep
sleep with the LFIOSC (32kHz) clock and the EC is cold. This fix
involves simply using a faster clock, 250kHz, when in low speed
deep sleep. This fix consumes more power but solves the bug.
Renamed EC console command dsleepmask to dsleep.
BRANCH=none
BUG=chrome-os-partner:23678
TEST=Go in to low speed deep sleep by going into either S3 or G3
and letting the EC console timeout. Then freeze-spray the EC chip.
Wake up the EC via the console and make sure that the idlestats
show that we have not missed a deadline.
Change-Id: I4f9844f1937bc8c95cf1540502f7d8fb4cbc097e
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175614
Reviewed-by: Randall Spangler <rspangler@chromium.org>
That way all the users of jump tags don't need to know about the
padding requirements.
BUG=chrome-os-partner:23851
BRANCH=none
TEST=enable CONFIG_CMD_JUMPTAGS, then 'jumptags'. Output should be
something like this:
20007fbc: 0x5550 UP.1 2
20007fc4: 0x4b42 KB.2 3
20007fcc: 0x4c50 LP.1 12
20007fdc: 0x4d54 MT.1 8
All the addresses in the first column should be word-aligned. The
sizes in the last column don't need to be a multiple of 4.
Change-Id: I91f9c29701a007ef8a56b5b7e0ea09930dfbea31
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175591
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Add bug references. Remove one assert that can no longer be triggered.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards; pass unit tests
Change-Id: I3f4d2e4f2f3343a8d0531cb0715d151eaa4d0b50
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175293
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
No code changes, just comment fixes. Added config #ifdefs for the
debug commands as requested; they're enabled for Spring, so
functionality is unchanged.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build spring; see that ilim and batdebug commands still exist
Change-Id: I7c9f12281afa7ec68aa7e62dcfcd51682d88a16a
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175216
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Rather than compile it by default for host-based tests, only compile
it for the few tests that actually use it. Since those (and all
boards) now only use if if they also have a keyscan task, we can get
rid of the #ifdefs in keyboard_mkbp.c as well.
And remove a TODO we'll never do...
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards; pass unit tests. These pass:
util/make_all.sh
make BOARD=pit tests
Change-Id: I44d1806cfb375027a7ed0b33a5e9bdbbed8ccddc
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/174513
There is a logical difference between PWM controls for things like
backlights and fan controls for actual fans. This change separates them into
two different data structures, for better abstraction.
BUG=chrome-os-partner:23530
BRANCH=none
TEST=manual
make runtests, make all boards, test on Link and Falco.
Change-Id: Ib63f2d1518fcc2ee367f81bf5d803360c1aa5c76
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175151
Instead of just configuring fan support as yes/no, we'll use it to specify
the number of fans on the board. Undefined (not zero!) means no fan support
at all.
Syntax change only. No new functionality.
BUG=chrome-os-partner:23530
BRANCH=none
TEST=manual
make runtests, build all platforms, build and test on Link.
Change-Id: Iff65efa69e05f3e1a54fdc2a8da9001b4e8487ca
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175150
This looks like a lot, but it's really just moving the non-board-specific
stuff from chip/lm4/fan.c into common/fan.c, updating the appropriate
headers, and renaming functions to better match the new location.
This is entirely code refactoring and renaming. No new functionality.
BUG=chrome-os-partner:23530
BRANCH=none
TEST=manual
make runtests, build all platforms, build and test on Link.
Change-Id: I7dc03d6732bad83cf838a86600b42a7cff5aa7aa
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175012
This is to add nyan board support:
- new files in board/nyan folder, including battery.c
- new common/chipset_tegra.c, which is mostly based on
chipset_gaia.c
- new include/tegra_power.h
- modified build.mk and flash_ec for nyan
BUG=none
BRANCH=nyan
TEST=tested on Venice 2 board
Change-Id: I36895f34f2f4d144a9440aff358c8274797ebbd6
Signed-off-by: Yen Lin <yelin@nvidia.com>
Reviewed-on: https://chromium-review.googlesource.com/168078
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
