In order to ensure we are always meeting the deadlines for the IRQ_HPD
pulse, increase the priority of the processing by moving the rising edge
from the low-priority HOOK task (in a deferred function) to the caller
task (which is the high-priority PD task).
The downside is we are now sleeping in the PD task blocking the
processing of the PD messages during this time.
Changed HPD_DSTREAM_DEBOUNCE_IRQ to 500us instead of 750us. According
to DP spec, the IRQ_HPD pulse width is between 500us and 1000us.
Ensure there is a minimum of 2ms delay in between each IRQ_HPD as specified
by the DP spec, by sleeping before sending the next pulse if needed.
(in practice, this should not wait if we are not too off processing the
messages)
BUG=chromium:711334
BRANCH=glados strago reef oak
TEST=manual, on SKL platform with kernel 3.18 and MST, verify display is
functional on USB-C dock.
Change-Id: Ib2e9dd608c5f1c671cc5a0fd979a5742101375ff
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/508629
Reviewed-by: Todd Broch <tbroch@chromium.org>
Adds min_frequency and max_frequency to struct motion_sensor_t.
New attributes min_frequency and max_frequency are now returned in
ectool's MOTIONSENSE_CMD_INFO response.
Incremented ectool's MOTIONSENSE_CMD_INFO version to version 3.
Add constants for MIN_FREQUENCY and MAX_FREQUENCY to each sensor's
header file.
BRANCH=none
BUG=chromium:615059
TEST=build/boot and verify MOTIONSENSE_CMD_INFO response on kevin,
make buildall -j passes.
Change-Id: I66db9715c122ef6bb4665ad5d086a9ecc9c7c93a
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/482703
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
power_button_x86.c and switch.c assume there is a lid switch. This
patch separate them so that a board with power button but with no
lid can be configured properly.
This patch also moves backlight control to the board directory
so that only the boards with a backlight turn it on/off when power
state changes.
BUG=none
BRANCH=none
TEST=boot fizz. make buildall.
Change-Id: If4070cdc4b1221fae68b35ec3497335d81f192fd
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/489602
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In npcx's fan driver, ec selected mode 5 and capturer A as tachometer's
input. Choosing TB2 as the second tachometer source is not correct since
we didn't initialize the registers for TB2. This patch modified the
second tachometer's input from TB2 to TA2 and passed the verification by
following changes.
1. Add the second fan settings in pwm_channels, fans, and mft_channels
arraies.
2. Modified ALTERNATE marco for pwm-type fans.
3. Set CONFIG_FAN from 1 to 2.
4. Set NPCX_TACH_SEL2 to 1 to test tachometer input 2. (ie.GPIO73/A6)
BRANCH=none
BUG=none
TEST=test dual fans with fanset command on npcx_evb and use faninfo for
verifying. Measure the actual rpm by scope.
Change-Id: Ia1af2732d9a64e24285d12371223eb0e77e53357
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/472310
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Servo_v4 requires the ability to have a different default state per
port. In previous devices, the assumption was that each supported port
had the same default usb pd state and power role. This CL moves the
by the default power role which in turn is derived from
CONFIG_USB_PD_DUAL_ROLE. In addiiton to moving the location, it now
uses 'port' as argument so it can be port specific if required.
PD_DEFAULT_STATE was a board.h specific config, but in practice each
instance used to date was set to PD_STATE_SNK_DISCONNECTED if
CONFIG_USB_PD_DUAL_ROLE was defined and set to
PD_STATE_SRC_DISCONNECTED otherwise.
BUG=chrome-os-partner:61878
BRANCH=servo
TEST=Manual run 'make -j buildall' to verify that all instances of
PD_DEFAULT_STATE were removed.
Change-Id: Iaf40718668732f525485ed7942ee7fc246d3f75d
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/431787
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
For oak, set a different list of task (no als, no accel) for compiling
revision 4 or less. Fix GPIO include issue.
BUG=chrome-os-partner:59423,chrome-os-partner:59084
TEST=compile for oak with board 4 and 5, tested on Reef.
BRANCH=kevin,reef
Change-Id: I09051a69cbad6d477a7b3bf9907f4c5c144b5136
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/424220
Reviewed-by: Randall Spangler <rspangler@chromium.org>
sensor private structure for bmi160 and bmp280 were defined
in the drivers themselves. It worked because there was only one
instance of each sensors on a board. However, this is an error it
should be in board files, as it was done for other sensors like the kionix.
BUG=none
TEST=buildall.
BRANCH=kevin,reef
Change-Id: Ica3aba358d141a7df9a3e97251d4c1e520cbf2c8
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/424218
Reviewed-by: Randall Spangler <rspangler@chromium.org>
If battery is not present, input current is set to PD_MAX_CURRENT_MA.
If the input power set is greater than the maximum allowed system power,
system might get damaged. Hence, limit the input current to meet maximum
allowed input system power.
BUG=chrome-os-partner:58498
BRANCH=none
TEST=Manually tested on Reef. Removed the battery & using 'charger'
console command observed the following.
With Zinger charger at 20V - Input current is set to 2.25A
With Type-C & other chargers - Input current is set to 3A
Change-Id: Ife8686f322e095aa74b740a7c469bfe87107fb9a
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/397865
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Common code is more flexible and supports more parts, so delete the
npcx-only register translation code.
BUG=chrome-os-partner:60029
BRANCH=gru
TEST=Manual on gru, run 'flashrom -p ec --wp-enable' and check that 0x28
gets written to SR1, which matches our desired 'protect botton 128KB',
according to the datasheet. Also run 'flashrom -p ec --erase' then read
back EC SPI contents, verify ROM is erased except for first 128KB
region.
Change-Id: I526401997ff7ec77f2a6047a4a9af74a671ed69a
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/413228
Reviewed-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 43634d36d273887b1f2349c333a7b4b229a83365)
Reviewed-on: https://chromium-review.googlesource.com/415498
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Add the default undefined state for CONFIG_ESPI and rename
CONFIG_VW_SIGNALS to CONFIG_ESPI_VW_SIGNALS.
BUG=chrome-os-partner:58666
BRANCH=none
TEST=pass presubmit checks
Change-Id: I45242d545915c16bb46f751532a01ab937cee5f0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/400032
Reviewed-by: Shawn N <shawnn@chromium.org>
When the kernel reads sensor data via LPC, it expects the order to be:
- ACCEL
- ACCEL
- GYRO
(other sensors data are read through EC commands)
BMI160 expects ACCEL, GYRO and MAG to be next to each other.
Reorganize motion_sensor array to fit these 2 requirements:
If BMI160 in the lid:
- BASE_ACCEL
- LID_ACCEL
- LID_GYRO
...
If BMI160 in the base:
- LID_ACCEL
- BASE_ACCEL
- BASE_GRYO
...
BUG=none
BRANCH=amenia,reef,wheatley
TEST=On reef, check the sensor data pull directly by the AP (for chrome
for lid angle) is correct. Check ARC++ works are expected.
Change-Id: If9477be0de44472e38a057c0b8533cb54acee220
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/394751
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
charge_manager may request a charge current limit less than the
capability of the supply in certain cases (eg. during PD voltage
transition, to make an effort to comply with reduced load spec).
Depending on the battery / system state, setting a reduced charge
current limit may result in brownout.
Pass the uncapped / max negotiated current to board_set_charge_limit()
so that boards may use it instead of the requested limit in such
circumstances.
BUG=chrome-os-partner:56139
BRANCH=gru
TEST=Manual on kevin with subsequent commit, boot system with zinger +
low-charge battery, verify devices powers up to OS without brownout.
Change-Id: I2b8e0d44edcf57ffe4ee0fdec1a1ed35c6becbbd
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/383732
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
When the charger is detached, the host event would sometimes be
sent before the charge info was updated, resulting in the host
thinking that the charger was still connected.
BUG=chrome-os-partner:55584
BRANCH=none
TEST=Connected charger to kevin 15 times and verified that the
icon was removed in 2-seconds or less.
Change-Id: I1a4e4e0f7cc23010210570fc261da8308d8e8070
Reviewed-on: https://chromium-review.googlesource.com/367809
Commit-Ready: Wonjoon Lee <woojoo.lee@samsung.com>
Tested-by: Sam Hurst <shurst@google.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Since pretty much always, we've declared console commands to take
a "longhelp" argument with detailed explanations of what the
command does. But since almost as long, we've never actually used
that argument for anything - we just silently throw it away in
the macro. There's only one command (usbchargemode) that even
thinks it defines that argument.
We're never going to use this, let's just get rid of it.
BUG=none
BRANCH=none
CQ-DEPEND=CL:*279060
CQ-DEPEND=CL:*279158
CQ-DEPEND=CL:*279037
TEST=make buildall; tested on Cr50 hardware
Everything builds. Since we never used this arg anyway, there had
better not be any difference in the result.
Change-Id: Id3f71a53d02e3dc625cfcc12aa71ecb50e35eb9f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/374163
Reviewed-by: Myles Watson <mylesgw@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Modified board level drivers for eSPI POC on wheatley. By adding CONFIG_ESPI
definition, ec can support espi protocols for host interface on x86 based
platform such as skylake and so on. CONFIG_VW_SIGNALS will be used in the
future for saving GPIOs during power sequence.
Modified sources:
1. wheatley/board.h: Enable/disable espi driver.
2, wheatley/board.c: Add VW signals in power signal list.
3. wheatley/gpio.inc: Save GPIOs if CONFIG_VW_SIGNALS is defined.
BRANCH=none
BUG=chrome-os-partner:34346
TEST=make BOARD=wheatley; test nuvoton IC specific drivers
Change-Id: I0e8a951de6eacd4f8be65ffaac242f38079375d5
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/366520
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This feature is inconsistent. Not all boards have such a symlink
(for a obvious reason).
This feature is fragile. It's most likely not tested and going to be
broken if not already. Developers won't like it if they have to test
two different ways to build boards before submitting patches.
This feature is not necessary. If you build EC in the standard way
(e.g. make BOARD=samus), these symlinks are not needed.
This feature is wasteful. Extra disk spaces are used and extra lines
are added to Makefile (increasing code complexity slightly).
BUG=chromium:626776
BRANCH=none
TEST=make buildall
Change-Id: Id5444284d773cb0e9225f39abd877441b8f61440
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/359321
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Not everything with a temperature sensor uses thermal throttling. This
change modifies the conditional build to enable building temp sensor
source without thermal throttling.
BUG=none
BRANCH=none
TEST=make buildall -j
Change-Id: I8c0753f12899e9f203c04477ae520bcda40d5fd8
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/356484
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Added console commands for the debugging purpose
psys - Can be used to measure the system power
amonbmon - Can be used to measure AMON/BMON voltage diff, current
BUG=chrome-os-partner:54273
BRANCH=none
TEST=Manually tested on Amenia
psys - Ran fish task and observed psys value changes.
amonbmon - AMON & BMON voltage & current are same as measured
across sense resistors.
Change-Id: I6653e814d9b00efe7dae9ce1fbd7ddbc2356f8e0
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/353043
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Previously CONFIG_USB_PD_TCPM_VBUS had two uses which were independent:
- When operating as a TCPC, it indicated that the VBUS level should be
tracked (through GPIO inputs) and sent to the external TCPM when
appropriate.
- When operating as a TCPM, it indicated that the VBUS level should be
obtained by querying the TCPC.
These two independent uses have been split into
CONFIG_USB_PD_TCPC_TRACK_VBUS and CONFIG_USB_PD_VBUS_DETECT_TCPC, which
sould be more clear.
In addition, CONFIG_USB_PD_VBUS_DETECT_* CONFIGs have been added for
other means of VBUS detection.
BUG=chromium:616580
BRANCH=None
TEST=Verify kevin continues to boot + charge.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I936821481d6577e17e3e9c61ff97c037574d6923
Reviewed-on: https://chromium-review.googlesource.com/348950
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Previously the maximum number of deferred routines was specified by the
the default maximum number of deferred routines you had to override
this, and if you wanted fewer, you still payed the price of having the
defer_until array statically allocated to be the maximum size.
This change removes that define and instead creates the RAM state of
the deferred routine (the time to wait until to call the deferred) when
the deferred is declared.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
manually test on discovery-stm32f072
Change-Id: Id3db84ee1795226b7818c57f68c1f637567831dc
Reviewed-on: https://chromium-review.googlesource.com/335597
Commit-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Previously calls to hook_call_deferred were passed the function to call,
which was then looked up in the .rodata.deferred section with a linear
search. This linear search can be replaced with a subtract by passing
the pointer to the deferred_data object created when DECLARE_DEFERRED
was invoked.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
CQ-DEPEND=CL:*255812
TEST=make buildall -j
Change-Id: I951dd1541302875b102dd086154cf05591694440
Reviewed-on: https://chromium-review.googlesource.com/334315
Commit-Ready: Bill Richardson <wfrichar@chromium.org>
Tested-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
After a charger is attached, we may set a charge limit based upon BC1.2
or USB-C Rp before PD negotiation completes. Therefore, allow 2 seconds
for all negotiation to complete. Previously this behavior was implicit
when using SW charge ramp.
BUG=chrome-os-partner:51280
BRANCH=glados
TEST=Manual on chell. Insert stock charger, verify that it is detected
as TYPE_UNKNOWN until timeout.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I52f02de46fa92b66a9fbaddb94a062310688f028
Reviewed-on: https://chromium-review.googlesource.com/334312
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In order to support 256 KB ram version of npcx ec, we add CHIP_VARIANT
variant to distinguish which verson ec is.
In config_chip.h, we use CHIP_VARIANT to specify the size and start address
of program memory. Ecst tool also needs a chip parameter to make sure
the address range checking of entry pointer won't fail.
Modified sources:
1. config_chip.h: Use CHIP_VARIANT to specify the different hardware spec
of npcx ec.
2. config_flash_layout.h: Replace constant value with
CONFIG_PROGRAM_MEMORY_SIZE for CONFIG_RO_SIZE.
3. build.mk: Add -chip parameter for ecst tool to check entry address.
4. npcx_evb\build.mk: Add CHIP_VARIANT definition (npcx5m5g).
5. npcx_evb_arm\build.mk: Add CHIP_VARIANT definition (npcx5m5g).
6. wheatley\build.mk: Add CHIP_VARIANT definition (npcx5m5g).
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: I1b8b9b9d0a59bdc01210f498ac67e4a342743b47
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/330072
Tested-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Previously the keyboard row and column pins could not use the GPIO
alternate function mechanism because their DEVALT bits were inverted
with respect to all of the others, making it impossible to correctly
configure them. With the refactor of the GPIO driver we can now add
the keyboard DEVALT entries to the gpio_alt_table, and use the
ALTERNATE macro and associated APIs to control the keyboard pin states.
The Wheatley RO firmware image is still 320 bytes smaller than before
the GPIO refactor.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Ran on Wheatley, manually verified keyboard functionality
Change-Id: Id04bc010834b5d95050b03ace6b0e1c5690757bf
Reviewed-on: https://chromium-review.googlesource.com/329762
Commit-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
With commit e9883124ff, a GPIO_INT macro was added. That change
also required that all instances of GPIO_INT in a board's
gpio.inc file come before any GPIO macros, or the interrupt
handler wouldn't work properly.
This CL just adds a warning comment about requirement to all
gpio.inc files.
BUG=chromium:471331
BRANCH=none
TEST=make buildall, test image on Cr50
This is a change to comments only. There is no new behavior to
verify, although I did run try out one new image just to be sure
nothing stupid happened.
Change-Id: I83f7819929a53bce3a8bae04d15b3ee3bda11738
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/329334
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Previously these were often done in board.c files, which made it
impossible to include the gpio.inc anywhere else. As part of
refactoring the GPIO code we now need to be able to include gpio.inc
from common/gpio.c. Moving these defines into gpio.inc makes them
available wherever gpio.inc is included.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Change-Id: I28e7b5a1d40b113ae824b18f020b2d1e51e0c08a
Reviewed-on: https://chromium-review.googlesource.com/328822
Commit-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
In order to prevent the influence of the deviation of AVCC during ADC
conversion, the internal reference voltage (Vref) of ADC is fixed to
2.816V even it derives from AVCC.
Modified sources:
1. wheatley/board.c: Modified max adc voltage of ADC to 28.160V.
2. adc_chip.h: Modified internal ref voltage of ADC to 2.816V.
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: Ib514f4bdc114802870eb3c77c650e18c05eb9617
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/327046
Reviewed-by: Shawn N <shawnn@chromium.org>
To get better power consumption in S0, we add FW support for
CONFIG_LOW_POWER_S0.
Before entering deep idle in S0, we must enable Host interrupt to wake up
EC if it needs to service LPC bus.
This version also add a new bit of sleep_mask (SLEEP_MASK_FAN) in system.h
to prevent EC enter deep idle if fan's duty isn't zero. Normally, the freq of
PWM fan is 25 kHz. It means we must select apb2 clock as the source clock of
PWM fan. Or fan would stop when ec enters deep idle because of no PWM signal.
In hwtimer.c, we reset the preload counter to maximum value in ITEI32's ISR
since preload counter is changed by __hw_clock_source_set all the time.
We also found there're no event set if it's deadline is over 32 bits but
current source clock isn't. To prevent ec doesn't wake-up in deep-idle even if
ITIM32 expires, FW set an event for ITIM32 after process_timers().
Modified sources:
1. wheatley/board.h: Add CONFIG_LOW_POWER_S0 definition.
2. clock.c: Enable Host interrupt for LPC.
3. clock.c: Disable LP_WK_CTL for better power consumption.
4. gpio.c: Add ISR for Host interrupt.
5. uart.c: Introduce bit 6 of USTAT to make sure transmitting is completed.
6. register.h: Add uart_clear_pending_wakeup function.
7. hwtimer.c: Fixed watchdog issue when ITIM32 is closed to overflow.
8. fan.c: Enable deep sleep if duty cycle is zero.
9. include/system.h: Add SLEEP_MASK_FAN for fan control loop.
10. core/cortex-m/task.c: Add "isb" to flash the garbage data in the
instruction pipeline.
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: Ibe3630d0d68cf3f32206adb2afa1b5958916a2be
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/324651
Reviewed-by: Shawn N <shawnn@chromium.org>
Convert some uses of gpio_set_flags_by_mask to plain gpio_set_flags.
The result is usually more readable due to being able to use the
GPIO_* enum names, and it removes more instances of port/mask
implementation details leaking outside the gpio.c chip specific code.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Change-Id: I06a7ad8a53e553a8e432a6abb5b38c25a98df6c6
Reviewed-on: https://chromium-review.googlesource.com/323815
Commit-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Configuring all GPIOs to INPUT / PULL_UP in hibernate is not a good
idea:
- INPUT / PULL_UP is not necessarially the lowest-power state (for
example, if there is an onboard pull-down).
- Most GPIOs should already be in lowest-power state when we're in S5.
- For the few GPIOs that need to be in a different state for hibernate,
we can use a board-level callback.
In addition, remove mec1322 code related to restoring from hibernate
state, since we always reset coming out of hibernate.
BUG=chrome-os-partner:49608
BRANCH=glados, strago
TEST=`hibernate` on chell console when in S5 and AC removed. Verify that
EC power is roughly equivalent to low-power idle power. Attach Zinger,
verify that device wakes and boots, and charges from charger.
Change-Id: Ib00ef035bec32cea3847eb38d743f5c0cec896ca
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/322937
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Modified hibernate funcs to support hibernate_wake_pins on weatley, npcx_evb
and npcx_evb_arm.
For better power consumption, we disable ADC, tri-state spi pins, all inputs
of wake-ups to prevent leakage current caused by input floating and set
necessary GPIOs' states in hibernate function.
Modified drivers:
1. npcx_evb/board.c: Add hibernate_wake_pins array for hibernate.
2. npcx_evb_arm/board.c: : Add hibernate_wake_pins array for hibernate.
3. wheatley/board.c: Add hibernate_wake_pins array for hibernate.
4. wheatley/board.c: Add board_set_gpio_state_hibernate func for adjusting
GPIOs' status related to board for better power consumption.
5. hwtimer.c: Remove unnecessary interrupt_enable/disable funcs. Interrupt
will disable before it is called.
6. register.h: Add WKINEN definition and declarations used for hibernate.
7. system.c: Add system_set_gpios_and_wakeup_inputs_hibernate to set GPIOs'
state and wake-up inputs before entering hibernate.
8. system_chip.h: Remove unused BBRM_DATA_INDEX_PBUTTON field.
9. gpio.c: Enable WKINEN in gpio_set_flags_by_mask func.
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: Ic85814065464095fdcb7a75964c2c528d8f8e62f
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/321466
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Replace Makefile with real link file in order to build sources in board folder.
Modified drivers:
1. Makefile: change file type to link file
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: Iba80166369869d661c8f6da989e3bc1c586047e7
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/320901
Reviewed-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Add i2cscan and kbpress commands for FAFT.
Remove unnecessary i2c reading since there is no race condition.
Bugs fixed:
Fixed i2c_read_string bug since we shouldn't enable NACK if flag doesn't
contain I2C_XFER_STOP.
Fixed i2c_unwedge bug since the parameter should be port not controller.
Fixed state machine bug since we should restore bus state back to idle
if bus encountered timeout.
Modified drivers:
1. board.h: Add i2cscan and kbpress commands for FAFT.
2. i2c.c: Remove unnecessary reading since there is no race condition.
3. i2c.c: Fixed i2c_read_string and i2c_unwedge bugs.
4. i2c.c: Restore to idle state if bus encountered timeout.
5. board.h: Add CONFIG_LOW_POWER_IDLE for better power consumption.
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: I98974f852cbbaec270c697feb8016b52550005bc
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/313393
Reviewed-by: Randall Spangler <rspangler@chromium.org>
To ease finer calculation of ec rate change units from
ms to us.
BRANCH=smaug
BUG=b:24367625
TEST=compile
Change-Id: I52057c8ca1b1180a64b58d1ba0af9ec53f40b026
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/312984
SERIRQ bug:
PMC1/2 share the same IRQ number 1 with default setting. Enable it will
influence 8042 protocols since KBC has no data but IRQ 1 is issued by
PMC.
AC detection bug:
GPIO definitions between AC_PRESENT and ACOK mismatched. AC_PRESENT will
always
be high even we don't plug the adaptor.
Modified drivers:
1. lpc.c: Remove enabling SERIRQ for PMC1/2 and disable IRQ12 for Mouse.
2. config_flash_layout.h: Modified for adjusting RAM size.
3. gpio.inc: Modified GPIO definitions for AC issue
4. board.h: Modified for adjusting RAM size and add support for ACC
5. board.c: Add support for ACC and adjust ADC max value
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: Ib330ef4078e4b06f1c01a2a6316e468b43d7a8d9
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/311933
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Change ADC channels on mec1322 boards to use scaling based on ADC
reference voltage of 3.0V instead of 3.3V. Also, setup the scaling
for AMON_BMON which reads the adapter input current or battery
current in mA.
BUG=none
BRANCH=none
TEST=tested on glados. use adc console command and verify it
roughly matches twinkie voltage and current.
Change-Id: Id6ed72012ebb1c23cf98a14ee6c156ec0f5fb586
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/311302
Reviewed-by: Shawn N <shawnn@chromium.org>
Add a new configuration struct tcpc_config_t that initially defines the
i2c host port and i2c slave address of all TCPCs present on the board.
This will allow us to create boards with multiple TCPCs on different i2c
ports, with arbitrary i2c slave addresses.
BUG=chromium:551078
TEST=Manual on glados. Verify PD communication / charging is still
functional on both PD ports.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I9b2bde85d7f1642e8727c052e064371be7967619
Reviewed-on: https://chromium-review.googlesource.com/311000
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Under NVDC, BGATE natively has a body diode. Hence there's a discharging
path if VSYS is lower than VBAT. This change keeps VSYS voltage when
turning off charging.
BRANCH=none
BUG=chrome-os-partner:46698
TEST=manual
make buildall -j
load on boards with isl9237 charger.
charge the battery to full, and check charging voltage and current.
Change-Id: I8a6046444dd40a3b57f034be124b9e8fe281de40
Signed-off-by: Rong Chang <rongchang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/309289
Reviewed-by: Alec Berg <alecaberg@chromium.org>
