On assertion of SLP_S0, EC goes to S0ix while system is in Lucid sleep
and EC is eligable to enter heavy sleep idle task.
Wakeup from S0ix by lid open, any key press, power button or track pad
will be done by PCH block by asserting SLP_S0.
At S0ix, 1 msec pulse will be generated every 8sec and this signal
should be ignored since this is NOT S0ix entry/exit related and defered
interrupt for SLP_S0 were added.
BRANCH=master
BUG=none
TEST=in OS shell, run following commands.
Following command is valid with coreboot with S0ix patches.
"echo freeze > /sys/power/state"
then,
Measure EC power consumption and compare it with one in S0.
And on EC console, there should be NO periodic message, "power
state 4 = S0ix, in 0x001d" every 8 sec.
Change-Id: Ia9cf5256b1ad7234815d4b6dbe2b45788aaf49dd
Signed-off-by: Kyoung Kim <kyoung.il.kim@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/307947
Commit-Ready: Kyoung Il Kim <kyoung.il.kim@intel.com>
Tested-by: Kyoung Il Kim <kyoung.il.kim@intel.com>
Reviewed-by: Kyoung Il Kim <kyoung.il.kim@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
This patch introduces a facility which would allow to compile in
callbacks for arbitrary commands passed over various communication
protocols.
Typically this will be used for testing, when various test commands
are multiplexed over an existing protocol.
The callbacks are associated with 16 bit command codes. On input the
callback receives a buffer, containing the command's argument, the
size of the command argument and the maximum size of the buffer. On
output the callback stores processing result in the same buffer and
updates the size to the actual amount of returned data.
Callback descriptors are stored in a dedicated read only section which
is scanned by extension_route_command() to find a callback associated
with a certain command code.
A console channel is also being introduced to allow controlling
console output generated by extension commands handlers.
BRANCH=none
BUG=chrome-os-partner:47524
TEST=none yet
Change-Id: I8ae16a78ca7d72176a5e7f74dd7a232078e7c06c
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/312586
Reviewed-by: Randall Spangler <rspangler@chromium.org>
On Ryu EVT2, where sensors share a 100kb i2c bus with other device,
when the sensors set to their maximal frequency and sampling interval
set to 5ms, the power management task would wait forever for the i2c
lock.
Increase the minimal amount of time the task can wait from 3ms to 8ms in
that case.
This is not an issue for Ryu PVT where the sensors are on a separate SPI
bus. However, on EVT, when setting the accelerometer/gyro over 125Hz, EC
won't be able to deliver the data in non-batched mode.
BRANCH=smaug
BUG=b:25510300
TEST=Without this change, an evt2 board would crash when plugging/unplugging
the charger while the sensors are set with:
echo 200000 > iio:device0/frequency # Accel
echo 5 > iio:device0/sampling_frequency
echo 200000 > iio:device1/frequency # Gyro
echo 25000 > iio:device2/frequency # Mag
Change-Id: Idb30da9ab8da61284388db73365c37be3a250dec
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/311755
Reviewed-by: Alec Berg <alecaberg@chromium.org>
This commit introduces a new CONFIG_* option. To utilise the
experimental console, simply define the following config option in the
board's board.h file.
#define CONFIG_EXPERIMENTAL_CONSOLE
This is a temporary option which allows the EC console to be work with
the EC-3PO interactive console interface. When this option is enabled,
the EC expects commands to packed in a particular format. This is for
command integrity and allows the interpreter to perform automatic
command retrying in the event that a character is dropped from the sent
command.
It also removes a lot of the console editing methods since they are now
being served by EC-3PO.
Once the EC-3PO interpreter is pulled into servod, we can enable this
feature by default and the config option can go away.
BUG=chrome-os-partner:46054
BRANCH=None
TEST=make -j buildall tests
TEST=Enable CONFIG_EXPERIMENTAL_CONSOLE on GLaDOS; Flash EC and verify
that console works via the EC-3PO interactive console interface.
TEST=Build and flash on GLaDOS and verify normal console operation on
standard EC UART.
CQ-DEPEND=CL:308615
Change-Id: I5e66eb94e31299b27ce029b7f7ce6ba0a7fb6816
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/309991
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This patch completes introduction of building of proper RO and RW
images for cr50.
A few small mods were required:
- both RO and RW images have to be signed, using the same dedicated
signer, but with different keys, dev_key.pem is not needed any more.
- the RW image offset is not at the half of available flash, a chip
specific value of 16K is used instead.
The suggested new image layout is as follows:
+----------------------------------------+
| 1KB RO signature header. |
+----------------------------------------+
- -
| 15KB RO image. |
- -
+========================================+
| 1KB RW-A signature header. |
+----------------------------------------+
- -
- -
| 239K RW-A image. |
- -
- -
+========================================+
- -
| 16 KB NVRAM, shared |
- -
+========================================+
| 1KB RW-B signature header. |
+----------------------------------------+
- -
- -
| 239K RW-B image. |
- -
- -
+========================================+
BRANCH=none
BUG=chrome-os-partner:43025
TEST=The combined image (build/cr50/ec.hex) is successfully loaded and
started by the spiflash utility from the latest FPGA tarball.
Corrupting a byte in the generated image in the RW section causes
failure to verify.
Change-Id: I41a05168b0d4e9f88efa1003f261b6dd03972a24
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/311422
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Add a new configuration struct tcpc_config_t that initially defines the
i2c host port and i2c slave address of all TCPCs present on the board.
This will allow us to create boards with multiple TCPCs on different i2c
ports, with arbitrary i2c slave addresses.
BUG=chromium:551078
TEST=Manual on glados. Verify PD communication / charging is still
functional on both PD ports.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I9b2bde85d7f1642e8727c052e064371be7967619
Reviewed-on: https://chromium-review.googlesource.com/311000
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
A previous commit caused ToT to use a not-yet-working bootloader.
This disables that bootloader by default so that the rest of us
can continue to work. ;-)
A configuration option is added to be able to address this issue in
the future with other boards as well.
BRANCH=None
BUG=chrome-os-partner:43025, chromium:551151
TEST=make buildall -j
Also verified that both normal and customized cr50 RO images build
and work as expected.
Change-Id: Ie433b07860cb1b04c12b2609c6fa39025fc0e515
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/310978
Under NVDC, BGATE natively has a body diode. Hence there's a discharging
path if VSYS is lower than VBAT. This change keeps VSYS voltage when
turning off charging.
BRANCH=none
BUG=chrome-os-partner:46698
TEST=manual
make buildall -j
load on boards with isl9237 charger.
charge the battery to full, and check charging voltage and current.
Change-Id: I8a6046444dd40a3b57f034be124b9e8fe281de40
Signed-off-by: Rong Chang <rongchang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/309289
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Some chips previously defined CONFIG_I2C and others didn't. Standardize
the usage by removing CONFIG_I2C from all config_chip files and force it
to be defined at the board level. Also, make boards define
CONFIG_I2C_MASTER and/or CONFIG_I2C_SLAVE based on the I2C interfaces
they will use - this will assist with some later cleanup.
BUG=chromium:550206
TEST=`make buildall -j`
BRANCH=None
Change-Id: I2f0970e494ea49611abc315587c7c9aa0bc2d14a
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/310070
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Define CONFIG_USB_PD_LOW_POWER by default to save power on both
TCPM and TCPC side by waking PD task less often when possible.
BUG=none
BRANCH=none
TEST=test on glados and samus.
Change-Id: I04441fb8339652cf073689177175a98f28807897
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/309311
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add support for two new configs to specify critical energy battery
percentage and critical external charger power. When we are under both
thresholds, set the LIMIT_POWER charger parameter to inform the AP that it
should conserve power to avoid brownout, and consider jumping to EC RW
to negotiate PD.
In addition, modify the existing CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON
to allow power-up regardless of power level if a 15W+ charger is
attached, since there is a reasonable chance it may speak PD and provide
sufficient power to boot the AP.
BUG=chromium:537269
TEST=Manual on Glados. Set CHG_MW thresh to 20000, BAT_PCT to 50. Verify
that LIMIT_POWER charger param is set until Zinger negotiates to 20V. Also
veify that system can boot with Donette.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Ic963c82fea4ad10e8a5d7e476c5ce3e5ae525dad
Reviewed-on: https://chromium-review.googlesource.com/306774
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
ARM systems currently use SBS kernel driver which talks to the battery
through I2C passthu in the EC. Instead when asking for battery
information try getting it from the charge state machine first, and
then try the battery if charge state does not have the information.
This reduces latency by cutting out the battery response time.
BUG=chromium:484841
BRANCH=none
TEST=check that power_supply_info works properly on Jerry
Change-Id: If4da15ccabe412adc31fc94b189089ebb3e9265c
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/307905
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Unless the lid is closed, the ALS is used for lightbar dimming.
Change the google colors depending on the light sensor result.
BUG=chrome-os-partner:44400
BRANCH=smaug
TEST=Check all 3 levels of brightness of the lightbar.
Check value using "adb shell ectool lightbar"
Check double tap color are not affected and is using full brightness.
Change-Id: I7b5e2890c3557f1dd3ae719f5f82ffb5fe7b24fb
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/301216
Reviewed-by: Alec Berg <alecaberg@chromium.org>
The only boards that had a port 80 task were the ones using the MEC1322.
Since that EC now has a dedicated timer interrupt configured for port80
writes, we can remove this code that was providing the port 80 task.
Additionally, the config option CONFIG_PORT80_TASK_EN is removed.
BUG=chrome-os-partner:46062
BRANCH=None
TEST=make -j buildall tests
CQ-DEPEND=CL:305591
Change-Id: I145d989b8872240e749ef77aabe0ae76fc94d443
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/305791
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Add CONFIG_I2C_SLAVE_ONLY for boards that only operate as a slave
on i2c.
BUG=chrome-os-partner:41959
BRANCH=none
TEST=make BOARD=glados_pd and see 2kB flash savings
Change-Id: I30831ce48b391d985c25e266229d5c6f2312042b
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/306783
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Certain ECs which cannot load both the RO and RW images into memory
simultaneously have a little firmware (LFW) loader that is loaded into
the beginning of the program memory. This loader is responsible for
loading the RO/RW images, however once we begin executing code from
main(), the loader has already completed it's purpose. We can reuse
this space by allocating portions of the .bss section here. This
currently saves us 3k for mec1322. This section is .bss.slow.
To use this feature simply define the following config option in
board.h.
#define CONFIG_REPLACE_LOADER_WITH_BSS_SLOW
In some cases, such as the mec1322, this region of RAM is optimized for
code and not data. Therefore, ideally infrequently used data should go
into this region.
BUG=chrome-os-partner:46056
BUG=chrome-os-partner:46063
BRANCH=None
TEST=Flash GLaDOS; sysjump rw; Verify that we are in rw; sysjump ro;
Verify we are back in ro.
TEST=Build GLaDOS, check output memory map for LDR_REGION and .bss.slow
section.
TEST=make -j buildall tests
Change-Id: I5b95cacc211278cf780a857b5a2ecfc1a0a28c45
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/305254
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Code for hard iron calibration: Every seconds (or faster if enough
samples), find a sphere that fit the compass data.
Based on Android code.
BRANCH=smaug
BUG=chrome-os-partner:39900
TEST=Check hard-iron bias is removed. Works better outside.
Change-Id: Iab479d5113b6560b4f01b0fd87373d2eecdb9b54
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/299583
Reviewed-by: Anton Staaf <robotboy@chromium.org>
Add a new define CONFIG_USB_PD_LOW_POWER_IDLE_WHEN_CONNECTED that
indicates the chip should try to go to low power idle even when a PD
connection is established -- this is the current behavior only for
Zinger.
Also, enable and disable the sleep mask bit from tcpc on rx enable /
disable.
BUG=chrome-os-partner:45010
TEST=Manual on glados / glados_pd. Insert Zinger, verify that glados_pd
stays out of low power idle. Remove Zinger, verify that glados_pd
resumes going into low power idle.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Ie763ae75f4459f56cad47d77d9c25d76358aa484
Reviewed-on: https://chromium-review.googlesource.com/303490
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
It may use MKBP event to send PD power change events to AP via interrupt.
According to the spec, AC power change events do not be allowed to
wake up AP. In order to avoid it, define a white list in board level,
only allow those events to wakeup the AP during S3 power state.
BRANCH=none
BUG=chrome-os-partner:45127
TEST=manual
Plug PD power adapter to oak, if system is in S3/S5 and it should
starts charging, but should not wake up system/AP at all.
Change-Id: I2f86697d5d3bd24d7de840e21064b91e8841f0eb
Signed-off-by: Ben Lok <ben.lok@mediatek.com>
Reviewed-on: https://chromium-review.googlesource.com/300360
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
On some systems, we may wish to have the PD follow the EC into
hibernate. Add a status field to EC_CMD_PD_EXCHANGE_STATUS to support
this.
BUG=chrome-os-partner:45010
TEST=Manual on glados with subsequent commit. Run 'hibernate' on EC
console, verify that both EC and PD go to hibernate. Plug zinger and
verify that both EC and PD wake, AP boots, and battery begins charging.
BRANCH=None
Change-Id: I0476bc8a47ffb0fe113dccda9d4f8074105c1c84
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/302712
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Export the board version through the usual EC_CMD_GET_BOARD_VERSION.
Add an option to use the board-specific board_get_version() callback
rather than doing the generic GPIO binary decoding since here the
version is ternary encoded.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=smaug
BUG=none
TEST=execute 'ectool boardversion' on the AP and see the right number.
Change-Id: I89c328573d09be02232756797ba3fdd5979b0292
Reviewed-on: https://chromium-review.googlesource.com/303368
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
(cherry picked from commit 6c620c51e5ab812b4e6751e4c630da2e6bee4b74)
Reviewed-on: https://chromium-review.googlesource.com/303803
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Add a build option CONFIG_BATTERY_CRITICAL_SHUTDOWN_CUT_OFF to perform a
battery cut-off when we reach the battery critical low level.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=smaug
BUG=none
TEST=Discharge a Ryu device down to the critical level, see the message
and verify we cannot restart with the power button. Also check that
plugging the charger revives the device and starts charging.
Change-Id: Ic132a658de5c5131a6a1dd1ce343196b68d480f6
Reviewed-on: https://chromium-review.googlesource.com/303549
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
(cherry picked from commit 80b3c99319771312d5733b126b6b3eb839addde9)
Reviewed-on: https://chromium-review.googlesource.com/303812
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Added code to enable the system power monitoring functionality to get the
details of the system power consumption.
And also added EC console command "psys" to get the system power consumption.
BUG=none
TEST=Manually tested on Kunimitsu.
Power = Voltage * Current, reading is equal to the power readings
from the psys command.
BRANCH=none
Change-Id: I62519ac96800363b67cab23cd9eb0dcac229cb47
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/302472
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Some sensors are in forced mode, motion sense must be scheduled at
their ODR. However the host may not want the data right away,
so motion task may not wake up the host that often.
Add a new variable motion_int_interval that defines the maximum interval
between FIFO host event.
BRANCH=smaug
BUG=chrome-os-partner:43800
TEST=Check that light sensor is polled at ODR frequency.
Check that when AP does not want any event, no FIFO host event are
requested.
Check CTS tests work as before.
Reenable motion_lid unit test.
Change-Id: Ie25e6cbe28fed899073856057855ffa03c0cd9fd
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/301134
Reviewed-by: Alec Berg <alecaberg@chromium.org>
RAM need not be preserved between jumps from the loader to RO/RW images,
so there is no need for a separate region of loader RAM. Remove
redundant CONFIGs which define this unneeded region.
BUG=None
TEST=Verify glados boots and sysjumps successfully.
BRANCH=None
Change-Id: I2567f17a973c6f9f00bcfd97a4581d6c4b6fd6f0
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/302586
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
For signed EC RW images (CONFIG_RWSIG), there's no point in
embedding the public key or signature into the image itself since
it will just be replaced by the signer (either as the next step
in the build process, or after the fact for MP releases). This
takes that out and just points to where the pubkey and signature
will be placed.
BUG=none
BRANCH=none
TEST=make buildall
I also checked the signatures with
futility show -t build/*/ec.bin
They still look good, and the one signed image I booted (Cr50)
works as before.
Change-Id: Ib39b7c508914851f81a1bebb2450e08ef0def76c
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/302630
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Since CONFIG_RO_SIZE and CONFIG_RW_SIZE now exist (which may
theoretically be different sizes), it is no longer useful to globally
define the size of an image.
BUG=chromium:535027
BRANCH=None
TEST=`make buildall -j`. Also, verify glados / glados_pd continue to
function as expected.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Ie29959923bc5d02b4d7d6d507ff2191bcb7d24c8
Reviewed-on: https://chromium-review.googlesource.com/301743
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Similar to i2c_xfer: allow access to a SPI device registers.
We assume the protocol use is set MSB bit to the offset for read
operation.
id is the index of the device in spi_devices.
BRANCH=smaug
TEST=Read/Write SPI registers.
BUG=none
Change-Id: Id4aaffbb6f514fd47086aee240b556ea23298d33
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/289857
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add an interface with the host to set up gesture recognition.
Today, only significant motion is supported.
Add a virtual sensor for concentrating gesture support from host.
BRANCH=smaug
BUG=b:23570481
TEST=On ryu, enable significant motion from host.
Change-Id: I906fa2d2d7b4ca2771ea2f58b91de8d97bf4e2e3
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/296213
Change the IRQ interface to allow adding events.
Move code to send the lightbar sequence from gesture.c to motion task.
TEST=compile, works on Ryu.
BRANCH=smaug
BUG=chrome-os-partner:44754
Change-Id: I981ea123ebef0e8e3d6aa320eade89f10e83b6fc
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/296822
Reviewed-by: Alec Berg <alecaberg@chromium.org>
1. Host access to the PNPCFG registers is disabled.
2. UART2 for host if necessary.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. host can't access the PNPCFG registers.
2. out I/O port 0x2f8 '0x30, 0x31, 0x32, 0x33, and 0x34'
will have console message '01234'.
Change-Id: If07bdc129105f5248661d929e6858d4063c452ee
Reviewed-on: https://chromium-review.googlesource.com/300266
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Add config option to use the old accelerometer reference frame,
which is used on samus and products using 3.14 or earlier kernel.
This fixes samus so that the lid angle calculation is correct
again.
This also moves the accel_orientation structure out of the board
directory and into common code, since it purely is a function of
the reference frame being used.
BUG=chrome-os-partner:43494
BRANCH=none
TEST=test on samus, verify lid angle calculation is correct once
again. also, enable the motion_lid test and verify that it passes.
Change-Id: I948a74a71964b54c68be66e828a030ddd0418947
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/300510
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Since there is no more concept of a flash region belonging only to the
EC, we only need one FLASH_SIZE config, which represents the actual
physical size of flash.
BRANCH=None
BUG=chrome-os-partner:23796
TEST=With entire patch series, on both Samus and Glados:
- Verify 'version' EC console command is correct
- Verify 'flashrom -p ec -r read.bin' reads back EC image
- Verify software sync correctly flashes both EC and PD RW images
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I18a34a943e02c8a029f330f213a8634a2ca418b6
Reviewed-on: https://chromium-review.googlesource.com/297824
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
In order to support architectures with non-contiguous writable and
protected regions, change storage offsets to be relative to writable and
protected regions, rather than relative to "the start of the region of
storage belonging to the EC".
Spec doc available at https://goo.gl/fnzTvr.
BRANCH=None
BUG=chrome-os-partner:23796
TEST=With entire patch series, on both Samus and Glados:
- Verify 'version' EC console command is correct
- Verify 'flashrom -p ec -r read.bin' reads back EC image
- Verify software sync correctly flashes both EC and PD RW images
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I796f8e7305a6336495bd256a78774595cb16a2e4
Reviewed-on: https://chromium-review.googlesource.com/297823
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
CDRAM / CODERAM configs were previously used for chips which copied code
from external SPI to program memory prior to execution, and were used
inconsistently between npcx and mec1322.
These CONFIGs are now completely redundant given new configs like
CONFIG_MAPPED_STORAGE_BASE and CONFIG_EXTERNAL_STORAGE.
BRANCH=None
BUG=chrome-os-partner:23796
TEST=With entire patch series, on both Samus and Glados:
- Verify 'version' EC console command is correct
- Verify 'flashrom -p ec -r read.bin' reads back EC image
- Verify software sync correctly flashes both EC and PD RW images
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I0e054ab4c939f9dcf54abee8e5ebd9b2e42fe9c4
Reviewed-on: https://chromium-review.googlesource.com/297804
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This commit adds a new basic driver for the Kionix KX022 Accelerometer.
Currently, the driver is capable of reading the sensor data and
manipulating its ODR, resolution, and range.
This sensor also has integrated support for Directional
Tap/Double-Tap(TM), however that functionality is not yet implemented in
the driver.
Lastly, since this accelerometer is very similar to the previous KXCJ9,
this commit tries to combine the drivers.
Note, the variant of the Kionix accelerometer MUST be specified in the
private data structure.
BUG=chrome-os-partner:43494
BRANCH=None
TEST=Build GLaDOS EC with driver enabled and verify that valid
accelerometer data is read, and that range, resolution, and odr can all
be modified.
TEST=Build samus EC image and verify that the lid still
works. Additionally, verify that I can change the odr, rate, and
resolution.
TEST=make buildall tests
Change-Id: I238ff1dc13f5342a93f8f701a0da85c52f25d214
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/299013
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Gesture recognition can be done in software (by the EC) or in
hardware, by the sensor itself.
Add variable to compile gesture.c only in the software case.
BRANCH=smaug
TEST=compile.
BUG=b:23570481
Change-Id: I22bef0bf744516df267020d9458e0299a4da3d72
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/296211
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Add support for ADC / thermistor reads on the EC's ADC
This will support now only ncp15wb but we can expand it
at future time.
BUG=chrome-os-partner:44764
TEST=make buildall -j
Manual on celes with subsequent commit. Boot to S0, run "temps".
Verify that temperatures are. See temperature is changing
BRANCH=None
Change-Id: If26d24b803dcff00c4c24e4e1f71d3b0de8e6738
Signed-off-by: Wonjoon Lee <woojoo.lee@samsung.com>
Reviewed-on: https://chromium-review.googlesource.com/296872
Reviewed-by: Shawn N <shawnn@chromium.org>
Separate the bd99992gw ADC interface from the NCP15WB thermistor
adc-to-temp maths so that the thermistor can be used with various
other interfaces.
BUG=chrome-os-partner:44764
TEST=make buildall -j
Manual on Glados. Boot to S0, run "temps".
Verify that temperatures start around 28C and begin to increase after
system is powered-on for a long duration.
BRANCH=None
Change-Id: I3e72e9f390feebaac2440dbe722485f8d1cf8c56
Signed-off-by: Wonjoon Lee <woojoo.lee@samsung.com>
Reviewed-on: https://chromium-review.googlesource.com/296871
Reviewed-by: Shawn N <shawnn@chromium.org>
Enabled the trickle charging mode by setting the MinSystemVoltage
register[0x3EH] to board specific battery voltage minimum value.
When the battery voltage drops below the battery voltage minimum
value, trickle charging enabled.
BUG=none
TEST=Manually tested on Kunimitsu FAB4 prototype.
Drained the battery below voltage minimum value. Using the
i2cxfer command observed Trickle charging mode is active in
the information register[0x3AH].
BRANCH=none
Change-Id: Id6416f2b0b74fda8cf3eafb95e044586f90b8a8e
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/298143
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Rong Chang <rongchang@chromium.org>
If the ALS is not enabled in S3/S5 states then it will generate
errors when trying to read so should be gated.
This could be done with a check for chipset_state or adding a
new CONFIG_ALS_POWER_GPIO to check. However the ALS is also not
needed when the host is in S3/S5 yet the task continues to run
in the background every 1 second.
This commit adds a new task enable/disable hook to disable the
task when the system is suspended and enable the task when it
is resumed.
In order to fit this new task in glados the als console command
is guarded by a new config option. Since this is not a very
frequently used/needed console command it is disabled by default.
And finally the kunimitsu and strago boards try to enable ALS
but they never actually enabled the ALS task so this new code was
failing to build because TASK_ID_ALS did not exist. Also samus
was enabling it but as TASK_NOTEST so tests will fail, though
they are disabled globally on samus.
BUG=chrome-os-partner:43493
BRANCH=none
TEST=enable ALS on glados and successfully build and use it,
also successfully build EC and tests for kunimitsu, strago,
and samus which are the other boards that use the ALS task.
Change-Id: I192940d7f306a1663c7cb789c313151bbb5f2b90
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/298156
Reviewed-by: Shawn N <shawnn@chromium.org>
Add option to charge automatically from dual-role devices. This
also changes the charge override behavior such that any new
device attached will clear the override because any new source
is a potential device we might charge from.
BUG=chrome-os-partner:44958
BRANCH=smaug
TEST=tested charge_manager unittests with
CONFIG_CHARGE_MANAGER_DRP_CHARGING both defined and undefined
Change-Id: Iac77ff0c501826d5fb5a9d50f88399ebc3955b87
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/297789
Reviewed-by: Shawn N <shawnn@chromium.org>
