To handle this, invoke hapd_subscriber.subscribe after the interface is created.
Also dont delete the interface from ifaces as ifaces should always contain the
configured ports (from uci config) per ieee8021x.uc design.
Deleting interfaces from ifaces will lead to ieee8021x.uc crashes.
Signed-off-by: Venkat Chimata <venkata@shasta.cloud>
Fix configurations for the WPA2 Enterprise example with 802.11r enabled for fast transitioning.
Signed-off-by: Firas Shaari <fshaari-c@telecominfraproject.com>
Fix null pointer dereference issue during Authentication stage and
add sanity check in mt7915_sta_statistics
Signed-off-by: John Crispin <john@phrozen.org>
In the bootcount script there was no entry for Edgecore EAP104 to
set the bootcount. This commit adds support for Edgecore EAP104 in
bootcount script to set the environment variable correctly
Signed-off-by: Venkat Chimata <venkata@shasta.cloud>
ubootenv_size is computed dynamically similar to ipq807x.
This resolves the issue where fw_setenv fails with the following error.
MTD erase error on /dev/mtd13: Invalid argument
Error: can't write fw_env to flash
Signed-off-by: Venkat Chimata <venkata@shasta.cloud>
In the backports driver the tx stats are updated in ieee80211_8023_xmit.
However in AP mode the packets are transmitted in ieee80211_8023_xmit_ap.
ieee80211_8023_xmit is not hit in case of AP mode. Update the stats just
before calling ieee80211_8023_xmit_ap
Signed-off-by: Venkat Chimata <venkata@shasta.cloud>
Enabling CPTCFG_ATH11K_MEM_PROFILE_512M will change the layout of
struct hal_rx_desc_ipq8074. This broke monitor mode. Fix it by not modifying
the struct even if the 512MB profile is enabled.
Fixes: WIFI-12102
Signed-off-by: John Crispin <john@phrozen.org>
This commit is an improvement over previous
commit 3598a243b3 which added a
fix for traffic disruption when vlan id of the lan port is
changed on devices with internal switches such as fap655,
CIG_WF186w,EAP-104.
This commit reconfigures the vlans for the mpsk clients on the
switch using the ucentral-event subsystem by tracking the
netifd_add events.
Fixes: WIFI-13797
Signed-off-by: joydeepbenison <joydeep.ghosh@benisontech.com>
ieee8021x
---------
1. Handle link_up events and update hostapd config
2. For certains scenarios, we need to remove and add
instead of reload (reload did not work).
Consider the following scenario -
Say on CIG 186w as an example
eth0.4086 interface exists with some non-ieee8021x config.
Push ieee8021x config. In general the flow is that
reload_config is called followed by invocation of services (from ucentral-schema)
Services inovation does n't wait until the configi reloaded ie in this context
ieee8021x service is invoked much before the network interfaces are recreated.
That is not correct. To handle this, we capture link-up events
and remove the existing interface (in hostapd as shown below) and add again
3. For swconfig platforms, the names contain a dot. Handle that gracefully in
ubus_unsub_object while adding hostapd interface
4. Add better logging using log.syslog
hostapd
---------
In case of swconfig switches, the basename of the interface should be based on the last dot.
Earlier it was done based on the first dot, which would result in incorrect basename.
For example if the interface name is eth0.4087 then the vlan->ifname would be eth0.4087. (A dot at the end) .
Before this patch, the basename was returned as eth0. It should be eth0.4087
Also fixed the return code by adding a default value of 0 and removed an unncessary check
for if_add before ubus add call.
Signed-off-by: Venkat Chimata <venkata@shasta.cloud>
when roaming between 2 radios the following error messages would show up in the logs
[681066.503943] ath11k c000000.wifi: Failed to add peer: 38:f9:d3:bf:b2:d4 for VDEV: 1
[681066.503979] ath11k c000000.wifi: Failed to add station: 38:f9:d3:bf:b2:d4 for VDEV: 1
Signed-off-by: John Crispin <john@phrozen.org>
