hostapd: initialize ht/vht/he mode on channel switch by default while using hostapd_cli chan_switch command

fixed: WIFI-14859
Signed-off-by: Tanya Singh <tanya_singh@accton.com>

feeds/hostapd/hostapd/patches/zzzz-002-initialize-mode-for-hostapd-cli-chan-switch.patch

@@ -0,0 +1,14 @@
+--- a/hostapd/ctrl_iface.c	2025-09-24 14:15:25.135668867 +0800
++++ b/hostapd/ctrl_iface.c	2025-09-24 15:32:46.082317382 +0800
+@@ -2657,6 +2657,11 @@ static int hostapd_ctrl_iface_chan_switc
+ 		break;
+ 	}
+ 
++    /* Initialize HT/VHT/HE parameters */
++    settings.freq_params.ht_enabled = iface->conf->ieee80211n;
++    settings.freq_params.vht_enabled = iface->conf->ieee80211ac;
++    settings.freq_params.he_enabled = iface->conf->ieee80211ax;
++
+ 	if (settings.freq_params.center_freq1)
+ 		dfs_range += hostapd_is_dfs_overlap(
+ 			iface, bandwidth, settings.freq_params.center_freq1);

feeds/ipq807x_v5.4/ath11k-wifi/Makefile

@@ -24,8 +24,6 @@ endef
 #
 
 ALLWIFIBOARDS:= \
-	cig-wf186w \
-	cig-wf186h \
 	cig-wf660a \
 	cig-wf194c \
 	cig-wf194c4 \
@@ -49,6 +47,9 @@ ALLWIFIBOARDS:= \
 	indio-um-310ax-v1 \
 	indio-um-510axp-v1 \
 	indio-um-510axm-v1 \
+	indio-um-325ax-v2 \
+	indio-um-335ax \
+	indio-um-525axp \
 	muxi-ap3220l \
 	plasmacloud-pax1800 \
 	wallys-dr5018 \
@@ -108,6 +109,16 @@ $(call Package/ath11k-wifi-default)
     TITLE:=cig-wf196 bdf
 endef
 
+define Package/ath11k-wifi-cig-wf186w
+$(call Package/ath11k-wifi-default)
+    TITLE:=cig-wf186w bdf
+endef
+
+define Package/ath11k-wifi-cig-wf186h
+$(call Package/ath11k-wifi-default)
+    TITLE:=cig-wf186h bdf
+endef
+
 define Package/ath11k-wifi-gl-ax1800
 $(call Package/ath11k-wifi-default)
     TITLE:=gl-ax1800 bdf
@@ -284,6 +295,24 @@ define Package/ath11k-wifi-cig-wf196/install
 	$(INSTALL_DATA) ./board-cig-wf196-us.bin.IPQ8074 $(1)/lib/firmware/ath11k/IPQ8074/hw2.0/board.bin.US
 endef
 
+define Package/ath11k-wifi-cig-wf186w/install
+	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/
+	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/qcn6122/hw1.0/
+	$(INSTALL_DATA) ./board-cig-wf186w-us.bin.IPQ5018 $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/board.bin.US
+	$(INSTALL_DATA) ./board-cig-wf186w-ca.bin.IPQ5018 $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/board.bin.CA
+	$(INSTALL_DATA) ./board-cig-wf186w-us.bin.QCN6122 $(1)/lib/firmware/ath11k/qcn6122/hw1.0/board.bin.US
+	$(INSTALL_DATA) ./board-cig-wf186w-ca.bin.QCN6122 $(1)/lib/firmware/ath11k/qcn6122/hw1.0/board.bin.CA
+endef
+
+define Package/ath11k-wifi-cig-wf186h/install
+	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/
+	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/qcn6122/hw1.0/
+	$(INSTALL_DATA) ./board-cig-wf186h-us.bin.IPQ5018 $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/board.bin.US
+	$(INSTALL_DATA) ./board-cig-wf186h-ca.bin.IPQ5018 $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/board.bin.CA
+	$(INSTALL_DATA) ./board-cig-wf186h-us.bin.QCN6122 $(1)/lib/firmware/ath11k/qcn6122/hw1.0/board.bin.US
+	$(INSTALL_DATA) ./board-cig-wf186h-ca.bin.QCN6122 $(1)/lib/firmware/ath11k/qcn6122/hw1.0/board.bin.CA
+endef
+
 define Package/ath11k-wifi-optimcloud-d50/install
 	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/IPQ5018/hw1.0/
 	$(INSTALL_DIR) $(1)/lib/firmware/ath11k/QCN9074/hw1.0/
@@ -393,8 +422,6 @@ define Package/ath11k-wifi-cig-wf188n/install
 	$(INSTALL_DATA) ./board-cig-wf188n-us.bin.IPQ6018 $(1)/lib/firmware/ath11k/IPQ6018/hw1.0/board.bin.US
 endef
 
-$(eval $(call generate-ath11k-wifi-package,cig-wf186w,Cigtech WF186w))
-$(eval $(call generate-ath11k-wifi-package,cig-wf186h,Cigtech WF186h))
 $(eval $(call generate-ath11k-wifi-package,cig-wf660a,Cigtech WF660a))
 $(eval $(call generate-ath11k-wifi-package,cig-wf194c,Cigtech WF194c))
 $(eval $(call generate-ath11k-wifi-package,cig-wf194c4,Cigtech WF194c4))
@@ -417,6 +444,9 @@ $(eval $(call generate-ath11k-wifi-package,liteon-wpx8324,Liteon WPX8324))
 $(eval $(call generate-ath11k-wifi-package,indio-um-310ax-v1,Indio UM-310AX V1))
 $(eval $(call generate-ath11k-wifi-package,indio-um-510axp-v1,Indio UM-510AXP V1))
 $(eval $(call generate-ath11k-wifi-package,indio-um-510axm-v1,Indio UM-510AXM V1))
+$(eval $(call generate-ath11k-wifi-package,indio-um-325ax-v2,Indio UM-325AX V2))
+$(eval $(call generate-ath11k-wifi-package,indio-um-335ax,Indio UM-335AX))
+$(eval $(call generate-ath11k-wifi-package,indio-um-525axp,Indio UM-525AXP))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630c-311g,Sonicfi RAP630C 311G))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630w-311g,Sonicfi RAP630W 311G))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630w-312g,Sonicfi RAP630W 312G))
@@ -440,6 +470,8 @@ $(eval $(call BuildPackage,ath11k-wifi-qcom-ipq8074))
 $(eval $(call BuildPackage,ath11k-wifi-qcom-ipq6018))
 $(eval $(call BuildPackage,ath11k-wifi-qcom-qcn9000))
 $(eval $(call BuildPackage,ath11k-wifi-cig-wf196))
+$(eval $(call BuildPackage,ath11k-wifi-cig-wf186w))
+$(eval $(call BuildPackage,ath11k-wifi-cig-wf186h))
 $(eval $(call BuildPackage,ath11k-wifi-motorola-q14))
 $(eval $(call BuildPackage,ath11k-wifi-optimcloud-d50))
 $(eval $(call BuildPackage,ath11k-wifi-optimcloud-d60))

feeds/ipq807x_v5.4/hostapd/files/afc_location.uc

@@ -4,19 +4,19 @@ let fs = require("fs");
 let ubus = require('ubus').connect();
 
 let gps_info = ubus.call('gps', 'info');
-let latitude = gps_info.latitude ?? 0;
-let longitude = gps_info.longitude ?? 0;
+let latitude = gps_info.latitude || 0;
+let longitude = gps_info.longitude || 0;
 
 // afc-location.json file content
 let afc_location = {};
 afc_location.location_type = "ellipse";
 afc_location.location = longitude + ":" + latitude ;
-afc_location.height = gps_info.elevation ?? 0;
+afc_location.height = gps_info.elevation || 0;
 afc_location.height_type = "AMSL";
-afc_location.major_axis = gps_info.major_axis ?? 0;
-afc_location.minor_axis = gps_info.minor_axis ?? 0;
-afc_location.orientation = gps_info.major_orientation ?? 0;
-afc_location.vertical_tolerance = gps_info.vdop ?? 0;
+afc_location.major_axis = int(gps_info.major_axis) || 1;
+afc_location.minor_axis = int(gps_info.minor_axis) || 1;
+afc_location.orientation = gps_info.major_orientation || 0;
+afc_location.vertical_tolerance = int(gps_info.vdop) || 1;
 
 let afc_location_json = fs.open("/etc/ucentral/afc-location.json", "w");
 afc_location_json.write(afc_location);

feeds/ipq807x_v5.4/hostapd/files/hostapd.uc

@@ -1,7 +1,8 @@
 let libubus = require("ubus");
-import { open, readfile } from "fs";
+import { open, readfile, writefile } from "fs";
 import { wdev_create, wdev_remove, is_equal, vlist_new, phy_is_fullmac, phy_open } from "common";
 
+let uci = require('uci').cursor();
 let ubus = libubus.connect(null, 60);
 
 hostapd.data.config = {};
@@ -893,10 +894,24 @@ return {
 		hostapd.ubus.disconnect();
 	},
 	afc_request: function(iface, data) {
-		let ret = ubus.call("afc", "request", { data });
-		if (type(ret) != "object")
-			return;
-		return ret.data;
+		let wireless_config = uci.get_all('wireless');
+		for (let l, afc_server in wireless_config) {
+			if (afc_server['.type'] == 'afc-server' && afc_server.url && data) {
+				hostapd.printf(`Sending AFC request: ${data}`);
+				writefile("/tmp/afc-request.json", data);
+
+				if (afc_server.access_token)
+					system(`curl -s -X POST ${afc_server.url} -H \'accept: \*\/\*\' -H \'Authorization: Bearer ${afc_server.access_token}\' -H \'Content-Type: application/json\' -d \'${data}\' --output /tmp/afc-response.json`);
+				else if (afc_server.cert)
+					system(`curl -s -X POST ${afc_server.url} -H \'accept: \*\/\*\' --cert \'${afc_server.cert}\' -H \'Content-Type: application/json\' -d \'${data}\' --output /tmp/afc-response.json`);
+
+				let afc_response = (readfile("/tmp/afc-response.json"));
+				if (afc_response)
+					return afc_response;
+				else
+					return;
+			}
+		}
 	},
 	bss_add: function(name, obj) {
 		bss_event("add", name);

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/board.d/01_leds

@@ -16,6 +16,13 @@ edgecore,eap104)
 	ucidef_set_led_netdev "wan" "wan" "yellow:uplink" "eth0"
         ucidef_set_led_default "power" "POWER" "green:power" "on"
 	;;
+indio,um-325ax-v2|\
+indio,um-335ax|\
+indio,um-525axp)
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "led_2g" "phy0tpt"
+	ucidef_set_led_wlan "wlan5g" "WLAN5G" "led_5g" "phy1tpt"
+	ucidef_set_led_default "power" "POWER" "led_sys" "on"
+	;;
 cig,wf186h|\
 cig,wf186w)
         ucidef_set_led_default "power" "POWER" "green:status" "on"

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/board.d/02_network

@@ -48,6 +48,14 @@ qcom_setup_interfaces()
 		ucidef_add_switch "switch1" \
 			"6u@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
 		;;
+	indio,um-325ax-v2|\
+	indio,um-335ax|\
+	indio,um-525axp)
+		ucidef_set_interface_wan "eth1"
+		ucidef_set_interface_lan "eth0"
+		ucidef_add_switch "switch1" \
+			"6@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
+		;;
 	emplus,wap385c|\
 	hfcl,ion4x_w|\
 	hfcl,ion4xi_w)

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -142,6 +142,9 @@ ath11k/IPQ5018/hw1.0/caldata.bin)
 	emplus,wap385c|\
 	hfcl,ion4x_w|\
 	hfcl,ion4xi_w|\
+	indio,um-325ax-v2|\
+	indio,um-335ax|\
+	indio,um-525axp|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
 	optimcloud,d50|\
@@ -183,6 +186,8 @@ ath11k/qcn6122/hw1.0/caldata_1.bin)
 	;;
 ath11k/qcn6122/hw1.0/caldata_2.bin)
 	case "$board" in
+	indio,um-325ax-v2|\
+	indio,um-525axp|\
 	wallys,dr5018|\
 	edgecore,eap104|\
 	edgecore,oap101-6e|\
@@ -201,6 +206,7 @@ ath11k/qcn6122/hw1.0/caldata_2.bin)
 	;;
 ath11k/QCN9074/hw1.0/caldata_1.bin)
 	case "$board" in
+	indio,um-335ax|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
 	optimcloud,d50|\
@@ -234,6 +240,8 @@ ath11k-macs)
 	edgecore,oap101|\
 	edgecore,oap101-6e|\
 	edgecore,oap101e-6e|\
+	indio,um-325ax-v2|\
+	indio,um-525axp|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
 	optimcloud,d50|\
@@ -251,6 +259,32 @@ ath11k-macs)
 		;;
 	esac
 	;;
+ath11k/IPQ5018/hw1.0/board.bin)
+	case "$board" in
+	cig,wf186w|\
+	cig,wf186h)
+                country=`cat /etc/ucentral/country`
+                if [ "$country" == "CA" ]; then
+                        ln -s /lib/firmware/ath11k/IPQ5018/hw1.0/board.bin.CA /lib/firmware/ath11k/IPQ5018/hw1.0/board.bin
+                else
+                        ln -s /lib/firmware/ath11k/IPQ5018/hw1.0/board.bin.US /lib/firmware/ath11k/IPQ5018/hw1.0/board.bin
+                fi
+                ;;
+	esac
+	;;
+ath11k/qcn6122/hw1.0/board.bin)
+	case "$board" in
+	cig,wf186w|\
+	cig,wf186h)
+                country=`cat /etc/ucentral/country`
+                if [ "$country" == "CA" ]; then
+                        ln -s /lib/firmware/ath11k/qcn6122/hw1.0/board.bin.CA /lib/firmware/ath11k/qcn6122/hw1.0/board.bin
+                else
+                        ln -s /lib/firmware/ath11k/qcn6122/hw1.0/board.bin.US /lib/firmware/ath11k/qcn6122/hw1.0/board.bin
+                fi
+                ;;
+	esac
+	;;
 *)
 	exit 1
 	;;

feeds/ipq807x_v5.4/ipq50xx/base-files/lib/upgrade/platform.sh

@@ -81,6 +81,9 @@ platform_check_image() {
 	wallys,dr5018|\
 	hfcl,ion4x_w|\
 	hfcl,ion4xi_w|\
+	indio,um-325ax-v2|\
+	indio,um-335ax|\
+	indio,um-525axp|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
 	optimcloud,d50|\
@@ -107,29 +110,45 @@ platform_do_upgrade() {
 
 	board=$(board_name)
 	case $board in
-	glinet,b3000|\
+	indio,um-325ax-v2|\
+	indio,um-335ax|\
+	indio,um-525axp|\
 	edgecore,oap101|\
 	edgecore,oap101-6e|\
 	edgecore,oap101e|\
 	edgecore,oap101e-6e|\
 	edgecore,eap104)
+		if [ "$(find_mtd_chardev rootfs)" ]; then
+			CI_UBIPART="rootfs"
+		else
+			if grep -q rootfs1 /proc/cmdline; then
+				CI_UBIPART="rootfs2"
+				CI_FWSETENV="active 2"
+			else
+				CI_UBIPART="rootfs1"
+				CI_FWSETENV="active 1"
+			fi
+		fi
+		nand_upgrade_tar "$1"
+		;;
+	glinet,b3000)
 		CI_UBIPART="rootfs1"
 		[ "$(find_mtd_chardev rootfs)" ] && CI_UBIPART="rootfs"
 		nand_upgrade_tar "$1"
 		;;
-        hfcl,ion4x_w|\
+	hfcl,ion4x_w|\
 	hfcl,ion4xi_w)
-                wp_part=$(fw_printenv primary | cut  -d = -f2)
-                echo "Current Primary is $wp_part"
-                if [[ $wp_part == 1 ]]; then
-                        CI_UBIPART="rootfs"
-                        CI_FWSETENV="primary 0"
-                else
-                        CI_UBIPART="rootfs_1"
-                        CI_FWSETENV="primary 1"
-                fi
-                nand_upgrade_tar "$1"
-                ;;
+		wp_part=$(fw_printenv primary | cut  -d = -f2)
+		echo "Current Primary is $wp_part"
+		if [[ $wp_part == 1 ]]; then
+				CI_UBIPART="rootfs"
+				CI_FWSETENV="primary 0"
+		else
+				CI_UBIPART="rootfs_1"
+				CI_FWSETENV="primary 1"
+		fi
+		nand_upgrade_tar "$1"
+		;;
 	cig,wf186w|\
 	cig,wf186h|\
 	emplus,wap385c|\

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-indio-um-325ax-v2.dts

@@ -0,0 +1,941 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "ipq5018.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "Indio UM-325AX V2";
+	compatible = "indio,um-325ax-v2", "qcom,ipq5018-mp03.5-c1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+                //led-failsafe = &led_red;
+                //led-running = &led_green;
+                //led-upgrade = &led_green;
+                //led-gateway = &led_blue;
+                //led-factory = &led_blue;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+	#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	#endif
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*                   256 MB Profile
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |           8MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x40800000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D100000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D300000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4E400000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4F300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4F400000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x4500000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x1400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xD00000>;
+		};
+
+		m3_dump: m3_dump@4D100000 {
+			no-map;
+			reg = <0x0 0x4D100000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E200000 {
+			no-map;
+			reg = <0x0 0x4E200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E300000 {
+			no-map;
+			reg = <0x0 0x4E300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E400000 {
+			no-map;
+			reg = <0x0 0x4E400000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4F300000 {
+			no-map;
+			reg = <0x0 0x4F300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F400000 {
+			no-map;
+			reg = <0x0 0x4F400000 0x0 0x100000>;
+		};
+		
+	#else
+	/*                 512MB/1GB Profiles
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x41000000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          14MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  Caldb   |  0x4D400000  |           2MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D600000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E600000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E700000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  Caldb   |  0x4E800000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4ED00000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4FD00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4FE00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  Caldb   |  0x4FF00000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x5400000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 01400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xE00000>;
+		};
+
+		m3_dump: m3_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0x100000>;
+		};
+
+		q6_caldb_region: q6_caldb_region@4D400000 {
+			no-map;
+			reg = <0x0 0x4D400000 0x0 0x200000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D600000 {
+			no-map;
+			reg = <0x0 0x4D600000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E600000 {
+			no-map;
+			reg = <0x0 0x4E600000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E700000 {
+			no-map;
+			reg = <0x0 0x4E700000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_1: q6_qcn6122_caldb_1@4E800000 {
+			no-map;
+			reg = <0x0 0x4E800000 0x0 0x500000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E900000 {
+			no-map;
+			reg = <0x0 0x4ED00000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4FD00000 {
+			no-map;
+			reg = <0x0 0x4FD00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4FE00000 {
+			no-map;
+			reg = <0x0 0x4FE00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_2: q6_qcn6122_caldb_2@4FF00000 {
+			no-map;
+			reg = <0x0 0x4FF00000 0x0 0x500000>;
+		};
+
+	#endif
+	};
+
+	soc {
+		gpio-watchdog {
+			compatible = "linux,wdt-gpio";
+			gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
+			hw_algo = "toggle";
+			hw_margin_ms = <5000>;
+			always-running;
+		};
+
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+
+			ethernet-phy@0 {
+				reg = <28>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x1>;
+			ess-switch@0x39c00000 {
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+						mdiobus = <&mdio0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <0x1c>;
+						mdiobus = <&mdio1>;
+						port_mac_sel = "QGMAC_PORT";
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+				ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x28>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <28>;
+					};
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <28>;
+			mdio-bus = <&mdio1>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		qcom,test@0 {
+			status = "ok";
+		};
+
+		nss-macsec1 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <0x1c>;
+			mdiobus = <&mdio1>;
+		};
+
+		lpass: lpass@0xA000000{
+			status = "disabled";
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		pcm_lb: pcm_lb@0 {
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio22", "gpio24", "gpio23", "gpio25";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+			pins = "gpio9";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_cs {
+			pins = "gpio8";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_0 {
+			pins = "gpio7";
+			function = "qspi0";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_1 {
+			pins = "gpio6";
+			function = "qspi1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_2 {
+			pins = "gpio5";
+			function = "qspi2";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_3 {
+			pins = "gpio4";
+			function = "qspi3";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+audio_pins: audio_pinmux {
+};
+        leds_pins: leds_pins {
+                led_5g {
+                        pins = "gpio34";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_2g {
+                        pins = "gpio33";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_sys {
+                        pins = "gpio26";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+		led_onekey {
+                        pins = "gpio28";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+        };
+};
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+        leds {
+                compatible = "gpio-leds";
+                pinctrl-0 = <&leds_pins>;
+                pinctrl-names = "default";
+
+                led_blue: led@34 {
+                        label = "led_5g";
+                        gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_5g";
+                        default-state = "off";
+                };
+                led_green: led@33 {
+                        label = "led_2g";
+                        gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_2g";
+                        default-state = "off";
+                };
+                led_red: led@26 {
+                        label = "led_sys";
+                        gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_sys";
+                        default-state = "off";
+                };
+		led@28 {
+                        label = "led_onekey";
+                        gpios = <&tlmm 28 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_onekey";
+                        default-state = "off";
+                };
+        };
+};
+
+&q6v5_wcss {
+	compatible = "qcom,ipq5018-q6-mpd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	firmware = "IPQ5018/q6_fw.mdt";
+	reg = <0x0cd00000 0x4040>,
+		<0x1938000 0x8>,
+		<0x193d204 0x4>;
+	reg-names = "qdsp6",
+			"tcsr-msip",
+			"tcsr-q6";
+	resets = <&gcc GCC_WCSSAON_RESET>,
+			<&gcc GCC_WCSS_Q6_BCR>;
+
+	reset-names = "wcss_aon_reset",
+			"wcss_q6_reset";
+
+	clocks = <&gcc GCC_Q6_AXIS_CLK>,
+		<&gcc GCC_WCSS_ECAHB_CLK>,
+		<&gcc GCC_Q6_AXIM_CLK>,
+		<&gcc GCC_Q6_AXIM2_CLK>,
+		<&gcc GCC_Q6_AHB_CLK>,
+		<&gcc GCC_Q6_AHB_S_CLK>,
+		<&gcc GCC_WCSS_AXI_S_CLK>;
+	clock-names = "gcc_q6_axis_clk",
+		"gcc_wcss_ecahb_clk",
+		"gcc_q6_axim_clk",
+		"gcc_q6_axim2_clk",
+		"gcc_q6_ahb_clk",
+		"gcc_q6_ahb_s_clk",
+		"gcc_wcss_axi_s_clk";
+
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+
+	qcom,rproc = <&q6v5_wcss>;
+	qcom,bootargs_smem = <507>;
+	boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>,
+			<0x2 0x4 0x2 0x12 0x0 0x0>;
+	status = "ok";
+	q6_wcss_pd1: remoteproc_pd1@4ab000 {
+		compatible = "qcom,ipq5018-wcss-ahb-mpd";
+		reg = <0x4ab000 0x20>;
+		reg-names = "rmb";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+					<&wcss_smp2p_in 9 0>,
+					<&wcss_smp2p_in 12 0>,
+					<&wcss_smp2p_in 11 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		resets = <&gcc GCC_WCSSAON_RESET>,
+				<&gcc GCC_WCSS_BCR>,
+				<&gcc GCC_CE_BCR>;
+		reset-names = "wcss_aon_reset",
+				"wcss_reset",
+				"ce_reset";
+
+		clocks = <&gcc GCC_WCSS_AHB_S_CLK>,
+				<&gcc GCC_WCSS_ACMT_CLK>,
+				<&gcc GCC_WCSS_AXI_M_CLK>;
+		clock-names = "gcc_wcss_ahb_s_clk",
+					"gcc_wcss_acmt_clk",
+					"gcc_wcss_axi_m_clk";
+
+		qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
+
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+					<&wcss_smp2p_out 9>,
+					<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>;
+	#else
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>, <&q6_caldb_region>;
+	#endif
+
+	};
+
+	q6_wcss_pd2: remoteproc_pd2 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "qcn6122/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 16 0>,
+					<&wcss_smp2p_in 17 0>,
+					<&wcss_smp2p_in 20 0>,
+					<&wcss_smp2p_in 19 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 16>,
+					<&wcss_smp2p_out 17>,
+					<&wcss_smp2p_out 18>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>;
+	#else
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>, <&q6_qcn6122_caldb_1>;
+	#endif
+
+	};
+
+	q6_wcss_pd3: remoteproc_pd3 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 24 0>,
+					<&wcss_smp2p_in 25 0>,
+					<&wcss_smp2p_in 28 0>,
+					<&wcss_smp2p_in 27 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 24>,
+					<&wcss_smp2p_out 25>,
+					<&wcss_smp2p_out 26>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef	__IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>;
+	#else
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>, <&q6_qcn6122_caldb_2>;
+	#endif
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x24>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4D400000 0x4D400000 0 0 0>;
+	qcom,caldb-size = <0x200000>;
+	mem-region = <&q6_ipq5018_data>;
+#else
+	memory-region = <&q6_ipq5018_data>;
+#endif
+	status = "ok";
+};
+
+&wifi1 {
+	/* QCN6122 5G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
+	qcom,rproc = <&q6_wcss_pd2>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x50>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4D600000 0x4D600000 0x4D300000 0x0 0x0>;
+	qcom,caldb-addr = <0x4E800000 0x4E800000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data1>;
+#else
+	memory-region = <&q6_qcn6122_data1>;
+#endif
+	status = "disabled";
+};
+
+&wifi2 {
+	/* QCN6122 6G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
+	qcom,rproc = <&q6_wcss_pd3>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0xb0>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4ED00000 0x4ED00000 0x4E400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4FF00000 0x4FF00000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data2>;
+#else
+	memory-region = <&q6_qcn6122_data2>;
+#endif
+	status = "ok";
+};
+
+
+&usb3 {
+	status = "ok";
+	device-power-gpio = <&tlmm 24 1>;
+};
+
+&dwc_0 {
+	/delete-property/ #phy-cells;
+	/delete-property/ phys;
+	/delete-property/ phy-names;
+};
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	#status = "disabled";
+	#perst-gpio = <&tlmm 18 1>;
+	perst-gpio = <&tlmm 18 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x2 {
+	#status = "disabled";
+	#perst-gpio = <&tlmm 15 1>;
+	perst-gpio = <&tlmm 15 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x1_rp {
+        status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+        status = "disabled";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+
+	};
+};
+

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-indio-um-335ax.dts

@@ -0,0 +1,731 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2025, Shubham Vishwakarma <shubhamvis98@fossfrog.in>.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "ipq5018.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "Indio UM-335AX";
+	compatible = "indio,um-335ax", "qcom,ipq5018-ap-mp03.1", "qcom,ipq5018-mp03.1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+		led-boot = &led_red;
+		led-failsafe = &led_red;
+		led-running = &led_red;
+		led-upgrade = &led_red;
+
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+		stdout-path = "serial0";
+	};
+
+	gpio-watchdog {
+		compatible = "linux,wdt-gpio";
+		gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
+		hw_algo = "toggle";
+		hw_margin_ms = <5000>;
+		always-running;
+	};
+
+	reserved-memory {
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x1800000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xE00000>;
+		};
+
+		m3_dump: m3_dump@4C800000 {
+			no-map;
+			reg = <0x0 0x4C800000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4C900000 {
+			no-map;
+			reg = <0x0 0x4C900000 0x0 0x100000>;
+		};
+
+		q6_caldb_region: q6_caldb_region@4CA00000 {
+			no-map;
+			reg = <0x0 0x4CA00000 0x0 0x200000>;
+		};
+
+		qcn9000_pcie0: qcn9000_pcie0@4cc00000 {
+			no-map;
+			reg = <0x0 0x4CC00000 0x0 0x2600000>;
+		};
+
+	#if defined(__CNSS2__)
+		mhi_region1: dma_pool1@4F200000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x0 0x4F200000 0x0 0x900000>;
+		};
+	#endif
+	};
+
+	soc {
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+
+			ethernet-phy@0 {
+				reg = <28>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x1>;
+			ess-switch@0x39c00000 {
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+						mdiobus = <&mdio0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <0x1c>;
+						mdiobus = <&mdio1>;
+						port_mac_sel = "QGMAC_PORT";
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+				ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x28>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <28>;
+					};
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <28>;
+			mdio-bus = <&mdio1>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		qcom,test@0 {
+			status = "ok";
+		};
+
+		nss-macsec1 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <0x1c>;
+			mdiobus = <&mdio1>;
+		};
+
+		lpass: lpass@0xA000000{
+			status = "disabled";
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		pcm_lb: pcm_lb@0 {
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio22", "gpio24", "gpio23", "gpio25";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+			pins = "gpio9";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_cs {
+			pins = "gpio8";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_0 {
+			pins = "gpio7";
+			function = "qspi0";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_1 {
+			pins = "gpio6";
+			function = "qspi1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_2 {
+			pins = "gpio5";
+			function = "qspi2";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_3 {
+			pins = "gpio4";
+			function = "qspi3";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	audio_pins: audio_pinmux {
+	};
+
+	leds_pins: leds_pins {
+		led_blue: led_5g {
+			label = "led_5g";
+			pins = "gpio34";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_green: led_2g {
+			label = "led_2g";
+			pins = "gpio33";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_red: led_sys {
+			label = "led_sys";
+			pins = "gpio26";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_onekey {
+			pins = "gpio28";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+};
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led@33 {
+			label = "led_5g";
+			gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "led_5g";
+			default-state = "off";
+		};
+		led@34 {
+			label = "led_2g";
+			gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "led_2g";
+			default-state = "off";
+		};
+		led@26 {
+			label = "led_sys";
+			gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "led_sys";
+			default-state = "on";
+		};
+		led@28 {
+			label = "led_onekey";
+			gpios = <&tlmm 28 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "led_onekey";
+			default-state = "off";
+		};
+	};
+};
+
+&q6v5_wcss {
+	compatible = "qcom,ipq5018-q6-mpd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	firmware = "IPQ5018/q6_fw.mdt";
+	reg = <0x0cd00000 0x4040>,
+		<0x1938000 0x8>,
+		<0x193d204 0x4>;
+	reg-names = "qdsp6",
+			"tcsr-msip",
+			"tcsr-q6";
+	resets = <&gcc GCC_WCSSAON_RESET>,
+			<&gcc GCC_WCSS_Q6_BCR>;
+
+	reset-names = "wcss_aon_reset",
+			"wcss_q6_reset";
+
+	clocks = <&gcc GCC_Q6_AXIS_CLK>,
+		<&gcc GCC_WCSS_ECAHB_CLK>,
+		<&gcc GCC_Q6_AXIM_CLK>,
+		<&gcc GCC_Q6_AXIM2_CLK>,
+		<&gcc GCC_Q6_AHB_CLK>,
+		<&gcc GCC_Q6_AHB_S_CLK>,
+		<&gcc GCC_WCSS_AXI_S_CLK>;
+	clock-names = "gcc_q6_axis_clk",
+		"gcc_wcss_ecahb_clk",
+		"gcc_q6_axim_clk",
+		"gcc_q6_axim2_clk",
+		"gcc_q6_ahb_clk",
+		"gcc_q6_ahb_s_clk",
+		"gcc_wcss_axi_s_clk";
+
+	memory-region = <&q6_mem_regions>, <&q6_etr_region>,
+			<&q6_caldb_region>;
+
+	qcom,rproc = <&q6v5_wcss>;
+	qcom,bootargs_smem = <507>;
+	boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>,
+			<0x2 0x4 0x2 0x12 0x0 0x0>;
+	status = "ok";
+	q6_wcss_pd1: remoteproc_pd1@4ab000 {
+		compatible = "qcom,ipq5018-wcss-ahb-mpd";
+		reg = <0x4ab000 0x20>;
+		reg-names = "rmb";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+					<&wcss_smp2p_in 9 0>,
+					<&wcss_smp2p_in 12 0>,
+					<&wcss_smp2p_in 11 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		resets = <&gcc GCC_WCSSAON_RESET>,
+				<&gcc GCC_WCSS_BCR>,
+				<&gcc GCC_CE_BCR>;
+		reset-names = "wcss_aon_reset",
+				"wcss_reset",
+				"ce_reset";
+
+		clocks = <&gcc GCC_WCSS_AHB_S_CLK>,
+				<&gcc GCC_WCSS_ACMT_CLK>,
+				<&gcc GCC_WCSS_AXI_M_CLK>;
+		clock-names = "gcc_wcss_ahb_s_clk",
+					"gcc_wcss_acmt_clk",
+					"gcc_wcss_axi_m_clk";
+
+		qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
+
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+					<&wcss_smp2p_out 9>,
+					<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>, <&q6_caldb_region>;
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	// status = "disabled";
+};
+
+&usb3 {
+	status = "ok";
+	device-power-gpio = <&tlmm 24 1>;
+};
+
+&dwc_0 {
+	/delete-property/ #phy-cells;
+	/delete-property/ phys;
+	/delete-property/ phy-names;
+};
+
+&blsp1_uart1 {
+	status = "ok";
+};
+
+&ssuniphy_0 {
+	status = "ok";
+};
+
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	perst-gpio = <&tlmm 18 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x2 {
+	status = "ok";
+	perst-gpio = <&tlmm 15 GPIO_ACTIVE_LOW>;
+};
+
+&wcss {
+	status = "ok";
+};
+
+&pcie_x2phy {
+	status = "ok";
+};
+
+&pcie_x1_rp {
+	status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+	status = "ok";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+		qrtr_instance_id = <0x20>;
+		qti,disable-rddm-prealloc;
+		qti,rddm-seg-len = <0x1000>;
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+#if defined(__CNSS2__)
+		memory-region = <0>,<&mhi_region1>;
+#else
+		base-addr = <0x4CB00000>;
+		m3-dump-addr = <0x4DF00000>;
+		etr-addr = <0x4E000000>;
+		qcom,caldb-addr = <0x4E100000>;
+		pageable-addr = <0x4E900000>;
+		qcom,tgt-mem-mode = <0x1>;
+#endif
+	};
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+	qcom,tgt-mem-mode = <1>;
+	qcom,board_id = <0x24>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4D400000 0x4D400000 0 0 0>;
+	qcom,caldb-size = <0x200000>;
+	mem-region = <&q6_ipq5018_data>;
+#else
+	memory-region = <&q6_ipq5018_data>;
+#endif
+	status = "ok";
+};
+
+&wifi3 {
+	/* QCN9000 5G */
+	board_id = <0xa0>;
+	hremote_node = <&qcn9000_pcie0>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/* QCN9000 tgt-mem-mode=2 layout - 17MB
+	 * +=========+==============+=========+
+	 * |  Region | Start Offset |   Size  |
+	 * +---------+--------------+---------+
+	 * | HREMOTE |  0x4C900000  |   11MB  |
+	 * +---------+--------------+---------+
+	 * | M3 Dump |  0x4D400000  |   1MB   |
+	 * +---------+--------------+---------+
+	 * |   ETR   |  0x4D500000  |   1MB   |
+	 * +---------+--------------+---------+
+	 * | Pageable|  0x4D600000  |   4MB   |
+	 * +==================================+
+	 */
+	base-addr = <0x4C900000>;
+	m3-dump-addr = <0x4D400000>;
+	etr-addr = <0x4D500000>;
+	caldb-addr = <0>;
+	pageable-addr = <0x4D600000>;
+	caldb-size = <0>;
+	hremote-size = <0xB00000>;
+	tgt-mem-mode = <0x2>;
+	pageable-size = <0x400000>;
+#elif __IPQ_MEM_PROFILE_512_MB__
+	/* QCN9000 tgt-mem-mode=1 layout - 26MB
+	 * +=========+==============+=========+
+	 * |  Region | Start Offset |   Size  |
+	 * +---------+--------------+---------+
+	 * | HREMOTE |  0x4CB00000  |   12MB  |
+	 * +---------+--------------+---------+
+	 * | M3 Dump |  0x4D700000  |   1MB   |
+	 * +---------+--------------+---------+
+	 * |   ETR   |  0x4D800000  |   1MB   |
+	 * +---------+--------------+---------+
+	 * |  Caldb  |  0x4D900000  |   8MB   |
+	 * +---------+--------------+---------+
+	 * | Pageable|  0x4E100000  |   4MB   |
+	 * +==================================+
+	 */
+	base-addr = <0x4CB00000>;
+	m3-dump-addr = <0x4D700000>;
+	etr-addr = <0x4D800000>;
+	caldb-addr = <0x4D900000>;
+	pageable-addr = <0x4E100000>;
+	caldb-size = <0x800000>;
+	hremote-size = <0xC00000>;
+	tgt-mem-mode = <0x1>;
+	pageable-size = <0x400000>;
+#else
+	/* QCN9000 tgt-mem-mode=0 layout - 53MB
+	 * +=========+==============+=========+
+	 * |  Region | Start Offset |   Size  |
+	 * +---------+--------------+---------+
+	 * | HREMOTE |  0x4CB00000  |   35MB  |
+	 * +---------+--------------+---------+
+	 * | M3 Dump |  0x4EE00000  |   1MB   |
+	 * +---------+--------------+---------+
+	 * |   ETR   |  0x4EF00000  |   1MB   |
+	 * +---------+--------------+---------+
+	 * |  Caldb  |  0x4F000000  |   8MB   |
+	 * +---------+--------------+---------+
+	 * | Pageable|  0x4F800000  |   8MB   |
+	 * +==================================+
+	 */
+	base-addr = <0x4CB00000>;
+	m3-dump-addr = <0x4EE00000>;
+	etr-addr = <0x4EF00000>;
+	caldb-addr = <0x4F000000>;
+	pageable-addr = <0x4F800000>;
+	hremote-size = <0x2300000>;
+	caldb-size = <0x800000>;
+	tgt-mem-mode = <0x0>;
+	pageable-size = <0x800000>;
+#endif
+	status = "ok";
+};

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-indio-um-525axp.dts

@@ -0,0 +1,941 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "ipq5018.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "Indio UM-525AXP";
+	compatible = "indio,um-525axp", "qcom,ipq5018-mp03.5-c1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+                //led-failsafe = &led_red;
+                //led-running = &led_green;
+                //led-upgrade = &led_green;
+                //led-gateway = &led_blue;
+                //led-factory = &led_blue;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+	#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	#endif
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*                   256 MB Profile
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |           8MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x40800000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D100000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D300000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4E400000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4F300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4F400000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x4500000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x1400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xD00000>;
+		};
+
+		m3_dump: m3_dump@4D100000 {
+			no-map;
+			reg = <0x0 0x4D100000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E200000 {
+			no-map;
+			reg = <0x0 0x4E200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E300000 {
+			no-map;
+			reg = <0x0 0x4E300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E400000 {
+			no-map;
+			reg = <0x0 0x4E400000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4F300000 {
+			no-map;
+			reg = <0x0 0x4F300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F400000 {
+			no-map;
+			reg = <0x0 0x4F400000 0x0 0x100000>;
+		};
+		
+	#else
+	/*                 512MB/1GB Profiles
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x41000000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          14MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  Caldb   |  0x4D400000  |           2MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D600000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E600000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E700000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  Caldb   |  0x4E800000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4ED00000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4FD00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4FE00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  Caldb   |  0x4FF00000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x5400000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 01400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xE00000>;
+		};
+
+		m3_dump: m3_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0x100000>;
+		};
+
+		q6_caldb_region: q6_caldb_region@4D400000 {
+			no-map;
+			reg = <0x0 0x4D400000 0x0 0x200000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D600000 {
+			no-map;
+			reg = <0x0 0x4D600000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E600000 {
+			no-map;
+			reg = <0x0 0x4E600000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E700000 {
+			no-map;
+			reg = <0x0 0x4E700000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_1: q6_qcn6122_caldb_1@4E800000 {
+			no-map;
+			reg = <0x0 0x4E800000 0x0 0x500000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E900000 {
+			no-map;
+			reg = <0x0 0x4ED00000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4FD00000 {
+			no-map;
+			reg = <0x0 0x4FD00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4FE00000 {
+			no-map;
+			reg = <0x0 0x4FE00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_2: q6_qcn6122_caldb_2@4FF00000 {
+			no-map;
+			reg = <0x0 0x4FF00000 0x0 0x500000>;
+		};
+
+	#endif
+	};
+
+	soc {
+		gpio-watchdog {
+			compatible = "linux,wdt-gpio";
+			gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
+			hw_algo = "toggle";
+			hw_margin_ms = <5000>;
+			always-running;
+		};
+
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+
+			ethernet-phy@0 {
+				reg = <28>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x1>;
+			ess-switch@0x39c00000 {
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+						mdiobus = <&mdio0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <0x1c>;
+						mdiobus = <&mdio1>;
+						port_mac_sel = "QGMAC_PORT";
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+				ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x28>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <28>;
+					};
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <28>;
+			mdio-bus = <&mdio1>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		qcom,test@0 {
+			status = "ok";
+		};
+
+		nss-macsec1 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <0x1c>;
+			mdiobus = <&mdio1>;
+		};
+
+		lpass: lpass@0xA000000{
+			status = "disabled";
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		pcm_lb: pcm_lb@0 {
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio22", "gpio24", "gpio23", "gpio25";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+			pins = "gpio9";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_cs {
+			pins = "gpio8";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_0 {
+			pins = "gpio7";
+			function = "qspi0";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_1 {
+			pins = "gpio6";
+			function = "qspi1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_2 {
+			pins = "gpio5";
+			function = "qspi2";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_3 {
+			pins = "gpio4";
+			function = "qspi3";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+audio_pins: audio_pinmux {
+};
+        leds_pins: leds_pins {
+                led_5g {
+                        pins = "gpio34";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_2g {
+                        pins = "gpio33";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_sys {
+                        pins = "gpio26";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+		led_onekey {
+                        pins = "gpio28";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+        };
+};
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+        leds {
+                compatible = "gpio-leds";
+                pinctrl-0 = <&leds_pins>;
+                pinctrl-names = "default";
+
+                led_blue: led@34 {
+                        label = "led_5g";
+                        gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_5g";
+                        default-state = "off";
+                };
+                led_green: led@33 {
+                        label = "led_2g";
+                        gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_2g";
+                        default-state = "off";
+                };
+                led_red: led@26 {
+                        label = "led_sys";
+                        gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_sys";
+                        default-state = "off";
+                };
+		led@28 {
+                        label = "led_onekey";
+                        gpios = <&tlmm 28 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_onekey";
+                        default-state = "off";
+                };
+        };
+};
+
+&q6v5_wcss {
+	compatible = "qcom,ipq5018-q6-mpd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	firmware = "IPQ5018/q6_fw.mdt";
+	reg = <0x0cd00000 0x4040>,
+		<0x1938000 0x8>,
+		<0x193d204 0x4>;
+	reg-names = "qdsp6",
+			"tcsr-msip",
+			"tcsr-q6";
+	resets = <&gcc GCC_WCSSAON_RESET>,
+			<&gcc GCC_WCSS_Q6_BCR>;
+
+	reset-names = "wcss_aon_reset",
+			"wcss_q6_reset";
+
+	clocks = <&gcc GCC_Q6_AXIS_CLK>,
+		<&gcc GCC_WCSS_ECAHB_CLK>,
+		<&gcc GCC_Q6_AXIM_CLK>,
+		<&gcc GCC_Q6_AXIM2_CLK>,
+		<&gcc GCC_Q6_AHB_CLK>,
+		<&gcc GCC_Q6_AHB_S_CLK>,
+		<&gcc GCC_WCSS_AXI_S_CLK>;
+	clock-names = "gcc_q6_axis_clk",
+		"gcc_wcss_ecahb_clk",
+		"gcc_q6_axim_clk",
+		"gcc_q6_axim2_clk",
+		"gcc_q6_ahb_clk",
+		"gcc_q6_ahb_s_clk",
+		"gcc_wcss_axi_s_clk";
+
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+
+	qcom,rproc = <&q6v5_wcss>;
+	qcom,bootargs_smem = <507>;
+	boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>,
+			<0x2 0x4 0x2 0x12 0x0 0x0>;
+	status = "ok";
+	q6_wcss_pd1: remoteproc_pd1@4ab000 {
+		compatible = "qcom,ipq5018-wcss-ahb-mpd";
+		reg = <0x4ab000 0x20>;
+		reg-names = "rmb";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+					<&wcss_smp2p_in 9 0>,
+					<&wcss_smp2p_in 12 0>,
+					<&wcss_smp2p_in 11 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		resets = <&gcc GCC_WCSSAON_RESET>,
+				<&gcc GCC_WCSS_BCR>,
+				<&gcc GCC_CE_BCR>;
+		reset-names = "wcss_aon_reset",
+				"wcss_reset",
+				"ce_reset";
+
+		clocks = <&gcc GCC_WCSS_AHB_S_CLK>,
+				<&gcc GCC_WCSS_ACMT_CLK>,
+				<&gcc GCC_WCSS_AXI_M_CLK>;
+		clock-names = "gcc_wcss_ahb_s_clk",
+					"gcc_wcss_acmt_clk",
+					"gcc_wcss_axi_m_clk";
+
+		qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
+
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+					<&wcss_smp2p_out 9>,
+					<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>;
+	#else
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>, <&q6_caldb_region>;
+	#endif
+
+	};
+
+	q6_wcss_pd2: remoteproc_pd2 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "qcn6122/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 16 0>,
+					<&wcss_smp2p_in 17 0>,
+					<&wcss_smp2p_in 20 0>,
+					<&wcss_smp2p_in 19 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 16>,
+					<&wcss_smp2p_out 17>,
+					<&wcss_smp2p_out 18>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>;
+	#else
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>, <&q6_qcn6122_caldb_1>;
+	#endif
+
+	};
+
+	q6_wcss_pd3: remoteproc_pd3 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 24 0>,
+					<&wcss_smp2p_in 25 0>,
+					<&wcss_smp2p_in 28 0>,
+					<&wcss_smp2p_in 27 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 24>,
+					<&wcss_smp2p_out 25>,
+					<&wcss_smp2p_out 26>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef	__IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>;
+	#else
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>, <&q6_qcn6122_caldb_2>;
+	#endif
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x24>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4D400000 0x4D400000 0 0 0>;
+	qcom,caldb-size = <0x200000>;
+	mem-region = <&q6_ipq5018_data>;
+#else
+	memory-region = <&q6_ipq5018_data>;
+#endif
+	status = "ok";
+};
+
+&wifi1 {
+	/* QCN6122 5G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
+	qcom,rproc = <&q6_wcss_pd2>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x50>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4D600000 0x4D600000 0x4D300000 0x0 0x0>;
+	qcom,caldb-addr = <0x4E800000 0x4E800000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data1>;
+#else
+	memory-region = <&q6_qcn6122_data1>;
+#endif
+	status = "disabled";
+};
+
+&wifi2 {
+	/* QCN6122 6G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
+	qcom,rproc = <&q6_wcss_pd3>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0xb0>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4ED00000 0x4ED00000 0x4E400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4FF00000 0x4FF00000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data2>;
+#else
+	memory-region = <&q6_qcn6122_data2>;
+#endif
+	status = "ok";
+};
+
+
+&usb3 {
+	status = "ok";
+	device-power-gpio = <&tlmm 24 1>;
+};
+
+&dwc_0 {
+	/delete-property/ #phy-cells;
+	/delete-property/ phys;
+	/delete-property/ phy-names;
+};
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	#status = "disabled";
+	#perst-gpio = <&tlmm 18 1>;
+	perst-gpio = <&tlmm 18 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x2 {
+	#status = "disabled";
+	#perst-gpio = <&tlmm 15 1>;
+	perst-gpio = <&tlmm 15 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x1_rp {
+        status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+        status = "disabled";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+
+	};
+};
+

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-rap630c-311g.dts

@@ -151,6 +151,14 @@
 			no-map;
 			reg = <0x0 0x4F000000 0x0 0x100000>;
 		};
+
+		ramoops: ramoops@4f100000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4f100000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#else
 	/*                 512MB/1GB Profiles
 	 * +==========+==============+=========================+
@@ -285,6 +293,13 @@
 			reg = <0x0 0x4F800000 0x0 0x500000>;
 		};
 
+		ramoops: ramoops@4fd00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4fd00000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#endif
 	};
 

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-rap630w-311g.dts

@@ -151,6 +151,14 @@
 			no-map;
 			reg = <0x0 0x4F000000 0x0 0x100000>;
 		};
+
+		ramoops: ramoops@4f100000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4f100000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#else
 	/*                 512MB/1GB Profiles
 	 * +==========+==============+=========================+
@@ -285,6 +293,13 @@
 			reg = <0x0 0x4F800000 0x0 0x500000>;
 		};
 
+		ramoops: ramoops@4fd00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4fd00000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#endif
 	};
 

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-rap630w-312g.dts

@@ -154,6 +154,14 @@
 			no-map;
 			reg = <0x0 0x4F000000 0x0 0x100000>;
 		};
+
+		ramoops: ramoops@4f100000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4f100000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#else
 	/*		 512MB/1GB Profiles
 	 * +==========+==============+=========================+
@@ -288,6 +296,13 @@
 			reg = <0x0 0x4F800000 0x0 0x500000>;
 		};
 
+		ramoops: ramoops@4fd00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4fd00000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#endif
 	};
 

feeds/ipq807x_v5.4/ipq50xx/image/ipq50xx.mk

@@ -93,6 +93,33 @@ define Device/edgecore_eap104
 endef
 TARGET_DEVICES += edgecore_eap104
 
+define Device/indio_um-325ax-v2
+  DEVICE_TITLE := Indio UM-325ax-V2
+  DEVICE_DTS := qcom-ipq5018-indio-um-325ax-v2
+  SUPPORTED_DEVICES := indio,um-325ax-v2
+  DEVICE_PACKAGES := ath11k-wifi-indio-um-325ax-v2 ath11k-firmware-ipq50xx-spruce ath11k-firmware-qcn6122
+  DEVICE_DTS_CONFIG := config@mp03.5-c1
+endef
+TARGET_DEVICES += indio_um-325ax-v2
+
+define Device/indio_um-335ax
+  DEVICE_TITLE := Indio UM-335ax
+  DEVICE_DTS := qcom-ipq5018-indio-um-335ax
+  SUPPORTED_DEVICES := indio,um-335ax
+  DEVICE_PACKAGES := ath11k-wifi-indio-um-335ax ath11k-firmware-qcn9000 ath11k-firmware-ipq50xx-spruce
+  DEVICE_DTS_CONFIG := config@mp03.1
+endef
+TARGET_DEVICES += indio_um-335ax
+
+define Device/indio_um-525axp
+  DEVICE_TITLE := Indio UM-525axp
+  DEVICE_DTS := qcom-ipq5018-indio-um-525axp
+  SUPPORTED_DEVICES := indio,um-525axp
+  DEVICE_PACKAGES := ath11k-wifi-indio-um-525axp ath11k-firmware-ipq50xx-spruce ath11k-firmware-qcn6122
+  DEVICE_DTS_CONFIG := config@mp03.5-c1
+endef
+TARGET_DEVICES += indio_um-525axp
+
 define Device/udaya_a6_id2
   DEVICE_TITLE := Udaya A6 - ID2
   DEVICE_DTS := qcom-ipq5018-udaya-a6-id2

feeds/ipq807x_v5.4/qca-ssdk/patches/500-define-mib-loop-cnt-to-gobal.patch

@@ -0,0 +1,61 @@
+--- a/include/init/ssdk_plat.h
++++ b/include/init/ssdk_plat.h
+@@ -330,6 +330,7 @@ struct qca_phy_priv {
+ 	struct mii_bus *miibus;
+ /*qca808x_end*/
+ 	u64 *mib_counters;
++	a_uint32_t mib_loop_cnt;
+ 	/* dump buf */
+ 	a_uint8_t  buf[2048];
+ 	a_uint32_t link_polling_required;
+--- a/src/ref/ref_mib.c
++++ b/src/ref/ref_mib.c
+@@ -479,39 +479,37 @@ qca_ar8327_sw_get_port_mib(struct switch
+ #endif
+
+ int
+-_qca_ar8327_sw_capture_port_tx_counter(struct qca_phy_priv *priv, int port)
++_qca_ar8327_sw_capture_port_tx_counter(a_uint32_t dev_id, int port)
+ {
+     fal_mib_info_t  mib_Info;
+
+     memset(&mib_Info, 0, sizeof(fal_mib_info_t));
+-    fal_get_tx_mib_info(priv->device_id, port, &mib_Info);
++    fal_get_tx_mib_info(dev_id, port, &mib_Info);
+
+     return 0;
+ }
+
+ int
+-_qca_ar8327_sw_capture_port_rx_counter(struct qca_phy_priv *priv, int port)
++_qca_ar8327_sw_capture_port_rx_counter(a_uint32_t dev_id, int port)
+ {
+     fal_mib_info_t  mib_Info;
+
+     memset(&mib_Info, 0, sizeof(fal_mib_info_t));
+-    fal_get_rx_mib_info(priv->device_id, port, &mib_Info);
++    fal_get_rx_mib_info(dev_id, port, &mib_Info);
+     return 0;
+ }
+
+ void
+ qca_ar8327_sw_mib_task(struct qca_phy_priv *priv)
+ {
+-	static int loop = 0;
+-
+ 	mutex_lock(&priv->reg_mutex);
+-	if ((loop % 2) == 0)
+-		_qca_ar8327_sw_capture_port_rx_counter(priv, loop/2);
++	if ((priv->mib_loop_cnt % 2) == 0)
++		_qca_ar8327_sw_capture_port_rx_counter(priv->device_id, priv->mib_loop_cnt/2);
+ 	else
+-		_qca_ar8327_sw_capture_port_tx_counter(priv, loop/2);
++		_qca_ar8327_sw_capture_port_tx_counter(priv->device_id, priv->mib_loop_cnt/2);
+
+-	if(++loop == (2 * (priv->ports))) {
+-		loop = 0;
++	if(++priv->mib_loop_cnt == (2 * (priv->ports))) {
++		priv->mib_loop_cnt = 0;
+ 	}
+
+ 	mutex_unlock(&priv->reg_mutex);

feeds/mediatek-sdk/mediatek/files-5.4/arch/arm64/boot/dts/mediatek/mt7981-edgecore-eap111.dts

@@ -200,7 +200,7 @@
 			phy-mode = "sgmii";
 			full-duplex;
 			pause;
-			airoha,surge = <1>;
+			airoha,surge = <0>;
 			airoha,polarity = <2>;
 		};
 

feeds/mediatek-sdk/mediatek/files-5.4/arch/arm64/boot/dts/mediatek/mt7981-edgecore-eap112.dts

@@ -169,7 +169,8 @@
 		compatible = "mediatek,eth-mac";
 		reg = <0>;
 		phy-mode = "sgmii";
-		phy-handle = <&phy1>;      // add phy handler
+		phy-handle = <&phy30>;
+		phy-handle2 = <&phy1>;
 		mtd-mac-address = <&factory 0x24>;
 	};
 
@@ -193,6 +194,16 @@
 			nvmem-cell-names = "phy-cal-data";
 		};
 
+		phy30: ethernet-phy@30 { // AN8801SB
+			compatible = "ethernet-phy-idc0ff.0421";
+			reg = <30>; //0x1e
+			phy-mode = "sgmii";
+			full-duplex;
+			pause;
+			airoha,surge = <0>;
+			airoha,polarity = <2>;
+		};
+
 		phy1: ethernet-phy@1 {
 			compatible = "ethernet-phy-id03a2.9471";
 			reg = <24>;            // set phy address to 0x18
@@ -200,9 +211,8 @@
 			reset-assert-us = <600>;
 			reset-deassert-us = <20000>;
 			phy-mode = "sgmii";
-    };
-
-        };
+		};
+	};
 };
 
 &hnat {

feeds/mediatek-sdk/mediatek/mt7981/base-files/etc/hotplug.d/iface/99-mtk-sr-scene-cond

@@ -34,13 +34,11 @@ case "$board" in
 
         if [ -f "$phy0_file" ]; then
             check_phy0=$(cat $phy0_file)
-            echo "check_phy0 = $check_phy0"
             [ "$check_phy0" == 0 ] && echo 1 > $phy0_file
         fi
 
         if [ -f "$phy1_file" ]; then
             check_phy1=$(cat $phy1_file)
-            echo "check_phy1 = $check_phy1"
             [ "$check_phy1" == 0 ] && echo 1 > $phy1_file
         fi
 

feeds/morse/utils/morse_mesh11sd/patches/002-remove-mesh-ifname-setting.patch

@@ -1,107 +0,0 @@
-# Description: The Mesh11sd daemon expects the mesh interface name to follow the format 'mesh<index>'. 
-# If it doesn't find this format, it attempts to set it in the UCI wireless configuration. 
-# However, when operating in other modes such as AP, STA, or Ad-Hoc, the script was patched to remove 
-# the mesh interface name from UCI. This process can lead to a race condition between the UI and Mesh11sd,
-# resulting in stale interface name values.
-# This patch resolves the issue by removing the setting of the interface name from the script, as it is 
-# now managed through the UI, ensuring consistency and eliminating the race condition.
-
---- a/src/mesh11sd
-+++ b/src/mesh11sd
-@@ -387,45 +387,45 @@ elif [ "$1" = "daemon" ]; then
- 
- 		if [ $mode -eq 5 ]; then
- 			# startup=4, statusmode=0, enabled=1
-+			syslogmessage="mesh11sd v$version has started: mesh management mode $mode"
- 			startup=0
- 			statusmode=0
- 			mode=1
--			syslogmessage="mesh11sd v$version has started: mesh management mode $mode"
- 
- 		elif [ $mode -eq 4 ]; then
- 			# startup=4, statusmode=0, enabled=0
-+			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
- 			startup=0
- 			statusmode=2
- 			mode=0
--			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
- 
- 		elif [ $mode -eq 3 ]; then
- 			# startup=0, statusmode=2, enabled=1
-+			syslogmessage="mesh11sd v$version has started: mesh management mode $mode"
- 			startup=0
- 			statusmode=0
- 			mode=1
--			syslogmessage="mesh11sd v$version has started: mesh management mode $mode"
- 
- 		elif [ $mode -eq 2 ]; then
- 			# startup=0, statusmode=2, enabled=0
-+			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
- 			startup=0
- 			statusmode=2
- 			mode=0
--			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
- 
- 		elif [ $mode -eq 1 ]; then
- 			# startup=0, statusmode=0, enabled=1
-+			syslogmessage="mesh11sd v$version has started, mesh management mode $mode"
- 			startup=0
- 			statusmode=0
- 			mode=1
--			syslogmessage="mesh11sd v$version has started, mesh management mode $mode"
- 
- 		elif [ $mode -eq 0 ]; then
- 			# startup=0, statusmode=0, enabled=0
-+			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
- 			startup=0
- 			statusmode=2
- 			mode=0
--			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
- 		fi
- 
- 		if [ $mode -ne $lastmode ]; then
-@@ -441,26 +441,6 @@ elif [ "$1" = "daemon" ]; then
- 			meshconfigs=$(uci show wireless 2> /dev/null | grep "mode='mesh'" | awk -F ".mode='mesh'" '{printf "%s " $1}')
- 
- 			if [ ! -z "$meshconfigs" ]; then
--				for meshconfig in $meshconfigs; do
--					ifname=$(uci get $meshconfig.ifname 2> /dev/null)
--
--					if [ -z "$ifname" ] || [ "$ifname" != "mesh$meshindex" ]; then
--						# No interface name in config, so add one
--						ucibatch="set $meshconfig.ifname='mesh$meshindex'"
--						echo "$ucibatch" | uci batch
--						changed=1
--						syslogmessage="Setting mesh interface name to [ mesh$meshindex ]"
--						write_to_syslog
--					fi
--					meshindex=$(($meshindex+1))
--				done
--
--				if [ "$changed" -eq 1 ]; then
--					changed=0
--					restart_mesh
--					continue
--				fi
--
- 				# get a list of interfaces
- 				get_mesh_iflist
- 
-@@ -482,13 +462,13 @@ elif [ "$1" = "daemon" ]; then
- 						# this is not a mesh interface
- 						continue
- 					else
--						# Check if this interface has a uci ifname
--						uciname=$(uci show wireless | grep "ifname='$iface'" | awk -F "." '{printf "wireless.%s" $2}')
-+						# Check if this interface mode is 'mesh'
-+						uciname=$(uci show wireless | grep "mode='mesh'" | awk -F "." '{printf "wireless.%s" $2}')
- 
- 						if [ -z "$uciname" ]; then
--							# Error - No interface name in config, we should have added one
-+							# Error - No interface with mode as mesh
- 							debugtype="err"
--							syslogmessage="Error getting mesh interface name"
-+							syslogmessage="Error getting mesh interface section"
- 							write_to_syslog
- 							continue
- 						fi

feeds/morse/utils/morse_mesh11sd/patches/002-remove-mesh-ifname-upon-disable.patch

@@ -0,0 +1,63 @@
+# Description: The Mesh11sd daemon sets the interface name 'mesh<index>' to the mesh interface.
+# However, even after disabling the mesh mode, this interface name persists, leading to confusion
+# when operating in other modes like AP/STA/Ad-Hoc, where the interface name continues to display as 'mesh<idx>'.
+# This patch addresses the issue by removing the 'mesh<idx>' interface name from the configuration when the device
+# is no longer in mesh mode. As this modification is not present in the upstream version, it is necessary to apply
+# this local patch to resolve the inconsistency
+
+diff --git a/src/mesh11sd b/src/mesh11sd
+index 85041d3..5f50e97 100755
+--- a/src/mesh11sd
++++ b/src/mesh11sd
+@@ -387,45 +387,45 @@ elif [ "$1" = "daemon" ]; then
+ 
+ 		if [ $mode -eq 5 ]; then
+ 			# startup=4, statusmode=0, enabled=1
++			syslogmessage="mesh11sd v$version has started: mesh management mode $mode"
+ 			startup=0
+ 			statusmode=0
+ 			mode=1
+-			syslogmessage="mesh11sd v$version has started: mesh management mode $mode"
+ 
+ 		elif [ $mode -eq 4 ]; then
+ 			# startup=4, statusmode=0, enabled=0
++			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
+ 			startup=0
+ 			statusmode=2
+ 			mode=0
+-			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
+ 
+ 		elif [ $mode -eq 3 ]; then
+ 			# startup=0, statusmode=2, enabled=1
++			syslogmessage="mesh11sd v$version has started: mesh management mode $mode"
+ 			startup=0
+ 			statusmode=0
+ 			mode=1
+-			syslogmessage="mesh11sd v$version has started: mesh management mode $mode"
+ 
+ 		elif [ $mode -eq 2 ]; then
+ 			# startup=0, statusmode=2, enabled=0
++			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
+ 			startup=0
+ 			statusmode=2
+ 			mode=0
+-			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
+ 
+ 		elif [ $mode -eq 1 ]; then
+ 			# startup=0, statusmode=0, enabled=1
++			syslogmessage="mesh11sd v$version has started, mesh management mode $mode"
+ 			startup=0
+ 			statusmode=0
+ 			mode=1
+-			syslogmessage="mesh11sd v$version has started, mesh management mode $mode"
+ 
+ 		elif [ $mode -eq 0 ]; then
+ 			# startup=0, statusmode=0, enabled=0
++			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
+ 			startup=0
+ 			statusmode=2
+ 			mode=0
+-			syslogmessage="mesh11sd v$version has started: mesh status mode $mode"
+ 		fi
+ 
+ 		if [ $mode -ne $lastmode ]; then

feeds/morse/utils/morse_mesh11sd/patches/003-accton_fix_ifname_confliction.patch

@@ -0,0 +1,39 @@
+--- a/src/mesh11sd	2024-09-06 17:13:52.075070001 +0800
++++ b/src/mesh11sd	2024-09-06 17:47:36.326914438 +0800
+@@ -434,7 +434,6 @@
+ 		fi
+ 
+ 		lastmode=$mode
+-		meshindex=0
+ 
+ 		if [ "$enabled" = 1 ]; then
+ 			#get list of mesh configs
+@@ -443,16 +442,19 @@
+ 			if [ ! -z "$meshconfigs" ]; then
+ 				for meshconfig in $meshconfigs; do
+ 					ifname=$(uci get $meshconfig.ifname 2> /dev/null)
+-
+-					if [ -z "$ifname" ] || [ "$ifname" != "mesh$meshindex" ]; then
+-						# No interface name in config, so add one
+-						ucibatch="set $meshconfig.ifname='mesh$meshindex'"
+-						echo "$ucibatch" | uci batch
+-						changed=1
+-						syslogmessage="Setting mesh interface name to [ mesh$meshindex ]"
+-						write_to_syslog
++					device=$(uci -q get $meshconfig.device)
++					device_type=$(uci -q get wireless.$device.type)
++					new_ifname="halow_mesh"
++					if [ "$device_type" == "morse" ]; then
++						if [ -z "$ifname" ] || [ "$ifname" != "$new_ifname" ]; then
++							# No interface name in config, so add one
++							ucibatch="set $meshconfig.ifname='$new_ifname'"
++							echo "$ucibatch" | uci batch
++							changed=1
++							syslogmessage="Setting mesh interface name to [ $new_ifname ]"
++							write_to_syslog
++						fi
+ 					fi
+-					meshindex=$(($meshindex+1))
+ 				done
+ 
+ 				if [ "$changed" -eq 1 ]; then

feeds/morse/utils/wpa_supplicant_s1g/Config.in

@@ -2,7 +2,7 @@ if PACKAGE_wpa_supplicant_s1g
 
 	config MORSE_WPA_SUPPLICANT_S1G_MESH_NETWORKING
 		bool
-		default n
+		default y
 		prompt "Enable mesh networking support"
 
 	config MORSE_WPA_SUPPLICANT_S1G_EAP

feeds/qca-wifi-7/ath12k-wifi/Makefile

@@ -43,6 +43,11 @@ $(call Package/ath12k-wifi-default)
     TITLE:=board-2.bin for EAP105
 endef
 
+define Package/ath12k-wifi-emplus-wap7635
+$(call Package/ath12k-wifi-default)
+    TITLE:=board-2.bin for WAP7635
+endef
+
 define Package/ath12k-wifi-sonicfi-rap7110c-341x
 $(call Package/ath12k-wifi-default)
     TITLE:=board-2.bin for RAP7710c_341x
@@ -88,6 +93,11 @@ $(call Package/ath12k-wifi-default)
     TITLE:=board-2.bin for NWA130BE
 endef
 
+define Package/ath12k-wifi-zyxel-nwa50be
+$(call Package/ath12k-wifi-default)
+    TITLE:=board-2.bin for NWA50BE
+endef
+
 define Package/ath12k-wifi-cig-wf672
 $(call Package/ath12k-wifi-default)
     TITLE:=board-2.bin for WF672
@@ -96,8 +106,8 @@ endef
 define Package/ath12k-wifi-cig-wf189/install
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
-	$(INSTALL_DATA) ./board-2.bin.wf189.QCN92XX $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/board-2.bin
-	$(INSTALL_DATA) ./board-2.bin.wf189.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
+	$(INSTALL_DATA) ./board-2.bin.wf189-us.QCN92XX $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/board-2.bin.US
+	$(INSTALL_DATA) ./board-2.bin.wf189-us.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin.US
 endef
 
 define Package/ath12k-wifi-edgecore-eap105/install
@@ -107,6 +117,13 @@ define Package/ath12k-wifi-edgecore-eap105/install
 	$(INSTALL_DATA) ./board-2.bin.eap105.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
 endef
 
+define Package/ath12k-wifi-emplus-wap7635/install
+	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
+	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/
+	$(INSTALL_DATA) ./board-2.bin.wap7635.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
+	$(INSTALL_DATA) ./board-2.bin.wap7635.QCN6274 $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/board-2.bin
+endef
+
 define Package/ath12k-wifi-sonicfi-rap7110c-341x/install
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
@@ -144,8 +161,8 @@ endef
 define Package/ath12k-wifi-cig-wf189w/install
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN6432/hw1.0/
-	$(INSTALL_DATA) ./board-2.bin.189w.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
-	$(INSTALL_DATA) ./board-2.bin.189w.QCN6432 $(1)/lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin
+	$(INSTALL_DATA) ./board-2.bin.189w-us.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin.US
+	$(INSTALL_DATA) ./board-2.bin.189w-us.QCN6432 $(1)/lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin.US
 	$(INSTALL_DATA) ./ipq5332_qcn6432.regdb $(1)/lib/firmware/ath12k/QCN6432/hw1.0/regdb.bin
 endef
 
@@ -153,8 +170,8 @@ endef
 define Package/ath12k-wifi-cig-wf189h/install
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN6432/hw1.0/
-	$(INSTALL_DATA) ./board-2.bin.189h.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
-	$(INSTALL_DATA) ./board-2.bin.189h.QCN6432 $(1)/lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin
+	$(INSTALL_DATA) ./board-2.bin.189h-us.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin.US
+	$(INSTALL_DATA) ./board-2.bin.189h-us.QCN6432 $(1)/lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin.US
 	$(INSTALL_DATA) ./ipq5332_qcn6432.regdb $(1)/lib/firmware/ath12k/QCN6432/hw1.0/regdb.bin
 endef
 
@@ -179,15 +196,24 @@ define Package/ath12k-wifi-zyxel-nwa130be/install
 	$(INSTALL_DATA) ./board-2.bin.nwa130be.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
 endef
 
+define Package/ath12k-wifi-zyxel-nwa50be/install
+	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN6432/hw1.0/
+	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
+	$(INSTALL_DATA) ./board-2.bin.nwa50be.QCN6432 $(1)/lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin
+	$(INSTALL_DATA) ./board-2.bin.nwa50be.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
+	$(INSTALL_DATA) ./ipq5332_qcn6432.regdb $(1)/lib/firmware/ath12k/QCN6432/hw1.0/regdb.bin
+endef
+
 define Package/ath12k-wifi-cig-wf672/install
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
-	$(INSTALL_DATA) ./board-2.bin.wf672.QCN92XX $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/board-2.bin
-	$(INSTALL_DATA) ./board-2.bin.wf672.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
+	$(INSTALL_DATA) ./board-2.bin.wf672-us.QCN92XX $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/board-2.bin.US
+	$(INSTALL_DATA) ./board-2.bin.wf672-us.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin.US
 endef
 
 $(eval $(call BuildPackage,ath12k-wifi-cig-wf189))
 $(eval $(call BuildPackage,ath12k-wifi-edgecore-eap105))
+$(eval $(call BuildPackage,ath12k-wifi-emplus-wap7635))
 $(eval $(call BuildPackage,ath12k-wifi-sonicfi-rap7110c-341x))
 $(eval $(call BuildPackage,ath12k-wifi-sonicfi-rap750e-h))
 $(eval $(call BuildPackage,ath12k-wifi-sonicfi-rap750e-s))
@@ -197,4 +223,5 @@ $(eval $(call BuildPackage,ath12k-wifi-cig-wf189h))
 $(eval $(call BuildPackage,ath12k-wifi-sercomm-ap72tip))
 $(eval $(call BuildPackage,ath12k-wifi-sercomm-ap72tip-v4))
 $(eval $(call BuildPackage,ath12k-wifi-zyxel-nwa130be))
+$(eval $(call BuildPackage,ath12k-wifi-zyxel-nwa50be))
 $(eval $(call BuildPackage,ath12k-wifi-cig-wf672))

feeds/qca-wifi-7/ath12k-wifi/board-2-nwa50be-IPQ5332.json

@@ -0,0 +1,20 @@
+[
+    {
+        "board": [
+            {
+                "names": [
+                    "bus=ahb,qmi-chip-id=0,qmi-board-id=18"
+                ],
+                "data": "nwa50be-IPQ5332.bin"
+            }
+        ],
+        "regdb": [
+            {
+                "names": [
+                    "bus=ahb,qmi-chip-id=0,qmi-board-id=18"
+                ],
+                "data": "ipq5332.regdb"
+            }
+        ]
+    }
+]

feeds/qca-wifi-7/ath12k-wifi/board-2-nwa50be-QCN6432.json

@@ -0,0 +1,20 @@
+[
+    {
+        "board": [
+            {
+                "names": [
+                    "bus=ahb,qmi-chip-id=0,qmi-board-id=112"
+                ],
+                "data": "nwa50be-QCN6432.bin"
+            }
+        ],
+        "regdb": [
+            {
+                "names": [
+                    "bus=ahb,qmi-chip-id=0,qmi-board-id=112"
+                ],
+                "data": "ipq5332_qcn6432.regdb"
+            }
+        ]
+    }
+]

feeds/qca-wifi-7/ath12k-wifi/generate.sh

@@ -18,3 +18,6 @@ $encoder -c board-2-ap72tip-v4-QCN92XX.json -o board-2.bin.ap72tip-v4.QCN92XX
 
 $encoder -c board-2-nwa130be-IPQ5332.json -o board-2.bin.nwa130be.IPQ5332
 $encoder -c board-2-nwa130be-QCN92XX.json -o board-2.bin.nwa130be.QCN92XX
+
+$encoder -c board-2-nwa50be-IPQ5332.json -o board-2.bin.nwa50be.IPQ5332
+$encoder -c board-2-nwa50be-QCN6432.json -o board-2.bin.nwa50be.QCN6432

feeds/qca-wifi-7/cig-platform-pkg/cig-wifi-mode-sw/Makefile

@@ -24,7 +24,9 @@ endef
 
 define KernelPackage/cig-wifi-mode-sw/install
 	$(INSTALL_DIR) $(1)/usr/sbin/
+	$(INSTALL_DIR) $(1)/etc/init.d/
 	$(INSTALL_BIN) ./files/cig_wifi_mode_sw $(1)/usr/sbin/cig_wms
+	$(INSTALL_BIN) ./files/cig_wifi_mode_boot $(1)/etc/init.d/cig_wmb
 endef
 
 $(eval $(call KernelPackage,cig-wifi-mode-sw))

feeds/qca-wifi-7/cig-platform-pkg/cig-wifi-mode-sw/files/cig_wifi_mode_boot

@@ -0,0 +1,13 @@
+#!/bin/sh /etc/rc.common
+
+START=60
+
+boot(){
+	local bands=$(cat /proc/rf_switch)
+
+	if [ "x$bands" = "x3" ]; then
+		echo "AFC is not ready, switch to 2-band mode" >/dev/console
+		echo 2 > /proc/rf_switch
+		firstboot -y -r
+	fi
+}

feeds/qca-wifi-7/hostapd/files/afc_location.uc

@@ -4,19 +4,19 @@ let fs = require("fs");
 let ubus = require('ubus').connect();
 
 let gps_info = ubus.call('gps', 'info');
-let latitude = gps_info.latitude ?? 0;
-let longitude = gps_info.longitude ?? 0;
+let latitude = gps_info.latitude || 0;
+let longitude = gps_info.longitude || 0;
 
 // afc-location.json file content
 let afc_location = {};
 afc_location.location_type = "ellipse";
 afc_location.location = longitude + ":" + latitude ;
-afc_location.height = gps_info.elevation ?? 0;
+afc_location.height = gps_info.elevation || 0;
 afc_location.height_type = "AMSL";
-afc_location.major_axis = gps_info.major_axis ?? 0;
-afc_location.minor_axis = gps_info.minor_axis ?? 0;
-afc_location.orientation = gps_info.major_orientation ?? 0;
-afc_location.vertical_tolerance = gps_info.vdop ?? 0;
+afc_location.major_axis = int(gps_info.major_axis) || 1;
+afc_location.minor_axis = int(gps_info.minor_axis) || 1;
+afc_location.orientation = gps_info.major_orientation || 0;
+afc_location.vertical_tolerance = int(gps_info.vdop) || 1;
 
 let afc_location_json = fs.open("/etc/ucentral/afc-location.json", "w");
 afc_location_json.write(afc_location);

feeds/qca-wifi-7/hostapd/files/common.uc

@@ -259,8 +259,13 @@ const phy_proto = {
 			addr[0] ^= idx << 2;
 			break;
 		case "b5":
-			if (mbssid)
+			if (mbssid) {
+				let b5 = addr[5];
+				addr[5] = addr[3];
+				addr[3] = b5;
+				addr[5] &= ~0xf;
 				addr[0] |= 2;
+			}
 			addr[5] ^= idx;
 			break;
 		default:

feeds/qca-wifi-7/hostapd/files/hostapd.uc

@@ -1,7 +1,8 @@
 let libubus = require("ubus");
-import { open, readfile } from "fs";
+import { open, readfile, writefile } from "fs";
 import { wdev_remove, is_equal, vlist_new, phy_is_fullmac, phy_open, wdev_set_radio_mask } from "common";
 
+let uci = require('uci').cursor();
 let ubus = libubus.connect(null, 60);
 
 hostapd.data.config = {};
@@ -1006,7 +1007,6 @@ let main_obj = {
 hostapd.data.ubus = ubus;
 hostapd.data.obj = ubus.publish("hostapd", main_obj);
 
-
 let auth_obj = {};
 hostapd.data.auth_obj = ubus.publish("hostapd-auth", auth_obj);
 
@@ -1026,10 +1026,24 @@ return {
 		hostapd.ubus.disconnect();
 	},
 	afc_request: function(iface, data) {
-		let ret = ubus.call("afc", "request", { data });
-		if (type(ret) != "object")
-			return;
-		return ret.data;
+		let wireless_config = uci.get_all('wireless');
+		for (let l, afc_server in wireless_config) {
+			if (afc_server['.type'] == 'afc-server' && afc_server.url && data) {
+				hostapd.printf(`Sending AFC request: ${data}`);
+				writefile("/tmp/afc-request.json", data);
+
+				if (afc_server.access_token)
+					system(`curl -s -X POST ${afc_server.url} -H \'accept: \*\/\*\' -H \'Authorization: Bearer ${afc_server.access_token}\' -H \'Content-Type: application/json\' -d \'${data}\' --output /tmp/afc-response.json`);
+				else if (afc_server.cert)
+					system(`curl -s -X POST ${afc_server.url} -H \'accept: \*\/\*\' --cert \'${afc_server.cert}\' -H \'Content-Type: application/json\' -d \'${data}\' --output /tmp/afc-response.json`);
+
+				let afc_response = (readfile("/tmp/afc-response.json"));
+				if (afc_response)
+					return afc_response;
+				else
+					return;
+			}
+		}
 	},
 	bss_create: function(phy, name, obj) {
 		phy = hostapd.data.config[phy];

feeds/qca-wifi-7/ipq53xx/base-files/etc/board.d/01_leds

@@ -7,6 +7,11 @@ board_config_update
 board=$(board_name)
 
 case "$board" in
+emplus,wap7635)
+	ucidef_set_led_default "ledb" "LEDB" "sys:blue" "on"
+	ucidef_set_led_default "ledg" "LEDG" "sys:green" "off"
+	ucidef_set_led_default "ledr" "LEDR" "sys:red" "off"
+	;;
 sercomm,ap72tip-v4|\
 sercomm,ap72tip)
 	ucidef_set_led_default "power" "POWER" "blue:status" "on"

feeds/qca-wifi-7/ipq53xx/base-files/etc/board.d/02_network

@@ -13,7 +13,6 @@ ipq53xx_setup_interfaces()
 		ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5" "eth0"
 		;;
 	cig,wf189|\
-	cig,wf672|\
 	edgecore,eap105|\
 	sercomm,ap72tip|\
 	sonicfi,rap750w-311a)
@@ -21,7 +20,8 @@ ipq53xx_setup_interfaces()
 		;;
 	sonicfi,rap7110c-341x|\
 	sonicfi,rap750e-h|\
-	sonicfi,rap750e-s)
+	sonicfi,rap750e-s|\
+	zyxel,nwa50be)
 		ucidef_set_interfaces_lan_wan "" "eth0"
 		;;
 	cig,wf189w)
@@ -32,6 +32,10 @@ ipq53xx_setup_interfaces()
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"
 		ucidef_add_switch "switch1" "0u@eth1" "3:lan" "2:lan"
 		;;
+	cig,wf672)
+		ucidef_set_interface_wan "eth0 eth1"
+		;;
+	emplus,wap7635|\
 	sercomm,ap72tip-v4)
 		ucidef_set_interface_wan "eth0"
 		;;	
@@ -104,6 +108,7 @@ qcom_setup_macs()
                 ucidef_set_wireless_macaddr_base 2g $(macaddr_add "$wan_mac" 2)
                 ucidef_set_wireless_macaddr_base 5g $(macaddr_add "$wan_mac" 3)
                 ;;
+        emplus,wap7635|\
         sercomm,ap72tip-v4)
                 wan_mac=$(cat /sys/class/net/eth0/address)
                 ucidef_set_wireless_macaddr_base 2g $(macaddr_add "$wan_mac" 1)
@@ -123,6 +128,16 @@ qcom_setup_macs()
 		ucidef_set_wireless_macaddr_base 5g $(macaddr_add "$wan_mac" 3)
 		ucidef_set_wireless_macaddr_base 6g $(macaddr_add "$wan_mac" 4)
 		;;
+	zyxel,nwa50be)
+		wan_mac=$(cat /proc/cmdline)
+		wan_mac="${wan_mac##*hwaddr=}"
+		wan_mac="${wan_mac%% *}"
+		wan_mac="$(echo ${wan_mac} | sed 's/\(..\)/\1:/g;s/:$//')"
+		ucidef_set_network_device_mac eth0 $wan_mac
+		ucidef_set_label_macaddr $wan_mac
+		ucidef_set_wireless_macaddr_base 2g $(macaddr_add "$wan_mac" 1)
+		ucidef_set_wireless_macaddr_base 5g $(macaddr_add "$wan_mac" 2)
+		;;
         *)
                 wan_mac=$(cat /sys/class/net/eth1/address)
                 lan_mac=$(macaddr_add "$wan_mac" 1)

feeds/qca-wifi-7/ipq53xx/base-files/etc/hotplug.d/firmware/10-ath12k-caldata

@@ -64,10 +64,12 @@ ath12k/IPQ5332/hw1.0/caldata.bin)
 	cig,wf189h|\
 	cig,wf189|\
 	edgecore,eap105|\
+	emplus,wap7635|\
 	sercomm,ap72tip-v4|\
 	sercomm,ap72tip|\
-	zyxel,nwa130be)
-		caldata_extract "0:ART" 0x1000 0x20000 
+	zyxel,nwa130be|\
+	zyxel,nwa50be)
+		caldata_extract "0:ART" 0x1000 0x20000
 		;;
 	cig,wf672)
 		cig_ipq5322_cal
@@ -86,6 +88,7 @@ ath12k/QCN92XX/hw1.0/cal-pci-0001:01:00.0.bin)
 	case "$board" in
 	cig,wf189|\
 	edgecore,eap105|\
+	emplus,wap7635|\
 	sercomm,ap72tip-v4|\
 	sercomm,ap72tip|\
 	zyxel,nwa130be)
@@ -122,6 +125,50 @@ ath12k/QCN6432/hw1.0/cal-ahb-soc@0:wifi2@c0000000.bin)
 	cig,wf189w)
 		caldata_extract "0:ART" 0x58800 0x20000
 		;;
+	zyxel,nwa50be)
+		caldata_extract "0:ART" 0x58800 0x2d000
+		;;
+	esac
+	;;
+ath12k/IPQ5332/hw1.0/board-2.bin)
+	case "$board" in
+	cig,wf189|\
+	cig,wf189h|\
+	cig,wf189w|\
+	cig,wf672)
+                country=`cat /etc/ucentral/country`
+                if [ "$country" == "CA" ]; then
+                        ln -s /lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin.CA /lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
+                else
+                        ln -s /lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin.US /lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
+                fi
+                ;;
+	esac
+	;;
+ath12k/QCN6432/hw1.0/board-2.bin)
+	case "$board" in
+	cig,wf189h|\
+	cig,wf189w)
+                country=`cat /etc/ucentral/country`
+                if [ "$country" == "CA" ]; then
+                        ln -s /lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin.CA /lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin
+                else
+                        ln -s /lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin.US /lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin
+                fi
+                ;;
+	esac
+	;;
+ath12k/QCN92XX/hw1.0/board-2.bin)
+	case "$board" in
+	cig,wf189|\
+	cig,wf672)
+                country=`cat /etc/ucentral/country`
+                if [ "$country" == "CA" ]; then
+                        ln -s /lib/firmware/ath12k/QCN92XX/hw1.0/board-2.bin.CA /lib/firmware/ath12k/QCN92XX/hw1.0/board-2.bin
+                else
+                        ln -s /lib/firmware/ath12k/QCN92XX/hw1.0/board-2.bin.US /lib/firmware/ath12k/QCN92XX/hw1.0/board-2.bin
+                fi
+                ;;
 	esac
 	;;
 *)

feeds/qca-wifi-7/ipq53xx/base-files/etc/init.d/phy_quirks

@@ -9,14 +9,5 @@ boot() {
 	edgecore,eap105)
 		ssdk_sh debug phy set 0x1 0x601FD032 0xff
 		;;
-	zyxel,nwa130be)
-		#eth0: APPE: phyaddr 4  green:2.5G  orange:others
-		ssdk_sh debug phy set 4 0x40078074 0x670
-		ssdk_sh debug phy set 4 0x40078078 0x8600
-
-		#eth1:  MHT: phyaddr 3  green:2.5G orange:others
-		ssdk_sh debug phy set 3 0x40078074 0x670
-		ssdk_sh debug phy set 3 0x40078078 0x8600
-		;;
 	esac
 }

feeds/qca-wifi-7/ipq53xx/base-files/lib/upgrade/platform.sh

@@ -136,7 +136,8 @@ platform_do_upgrade() {
 	sercomm,ap72tip|\
 	cig,wf189w|\
 	cig,wf189h|\
-	cig,wf189)
+	cig,wf189|\
+	emplus,wap7635)
 		if [ -f /proc/boot_info/bootconfig0/rootfs/upgradepartition ]; then
 			CI_UBIPART="$(cat /proc/boot_info/bootconfig0/rootfs/upgradepartition)"
 			CI_BOOTCFG=1
@@ -173,7 +174,8 @@ platform_do_upgrade() {
 		sonicfi_dualimage_check
 		nand_upgrade_tar "$1"
 		;;
-	zyxel,nwa130be)
+	zyxel,nwa130be|\
+	zyxel,nwa50be)
 		nand_upgrade_tar "$1"
 		;;
 	esac

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-emplus-wap7635.dts

@@ -0,0 +1,413 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ5332 RDP468 board device tree source
+ *
+ * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "ipq5332.dtsi"
+#include "ipq5332-default-memory.dtsi"
+
+/ {
+	model = "Emplus WAP7635";
+	compatible = "emplus,wap7635", "qcom,ipq5332-ap-mi01.6", "qcom,ipq5332";
+
+	aliases {
+		serial0 = &blsp1_uart0; /*console*/
+		ethernet0 = "/soc/dp1";
+
+        led-boot = &led_power_green;
+        led-failsafe = &led_power_red;
+        led-running = &led_power_green;
+        led-upgrade = &led_power_green;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc@0 {
+		mdio:mdio@90000 {
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 51 GPIO_ACTIVE_LOW>;
+			phyaddr_fixup = <0xC90F018>;
+			uniphyaddr_fixup = <0xC90F014>;
+			mdio_clk_fixup; /* MDIO clock sequence fix up flag */
+			status = "okay";
+
+			phy0: ethernet-phy@0 {
+				reg = <24>;
+			};
+		};
+
+		ess-instance {
+			/*num_devices = <0x1>;*/
+			ess-switch@3a000000 {
+				switch_cpu_bmp = <0x1>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x2>; /* lan port bitmap */
+				switch_wan_bmp = <0>; /* wan port bitmap */
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance0*/
+				switch_mac_mode1 = <0xd>; /* mac mode for uniphy instance1*/
+				switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
+
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <24>;
+						mdiobus = <&mdio>;
+						ethernet-phy-ieee802.3-c45;
+					};
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			qcom,id = <1>;
+			reg = <0x3a500000 0x4000>;
+			qcom,mactype = <1>;
+			local-mac-address = [000000000000];
+			mdio-bus = <&mdio>;
+			qcom,phy-mdio-addr = <24>;
+			qcom,link-poll = <1>;
+			phy-mode = "sgmii";
+			/* phy-mode = "usxgmii"; */
+		};
+
+		/* EDMA host driver configuration for the board */
+		edma@3ab00000 {
+			qcom,txdesc-ring-start = <4>;		/* Tx desc ring start ID */
+			qcom,txdesc-rings = <12>;			/* Total number of Tx desc rings to be provisioned */
+			qcom,mht-txdesc-rings = <8>;		/* Extra Tx desc rings to be provisioned for MHT SW ports */
+			qcom,txcmpl-ring-start = <4>;		/* Tx complete ring start ID */
+			qcom,txcmpl-rings = <12>;			/* Total number of Tx complete rings to be provisioned */
+			qcom,mht-txcmpl-rings = <8>;		/* Extra Tx complete rings to be provisioned for mht sw ports. */
+			qcom,rxfill-ring-start = <4>;		/* Rx fill ring start ID */
+			qcom,rxfill-rings = <4>;			/* Total number of Rx fill rings to be provisioned */
+			qcom,rxdesc-ring-start = <12>;		/* Rx desc ring start ID */
+			qcom,rxdesc-rings = <4>;			/* Total number of Rx desc rings to be provisioned */
+			qcom,rx-page-mode = <0>;			/* Rx fill ring page mode */
+			qcom,tx-map-priority-level = <1>;	/* Tx priority level per port */
+			qcom,rx-map-priority-level = <1>;	/* Rx priority level per core */
+			qcom,ppeds-num = <2>;				/* Number of PPEDS nodes */
+
+			/* PPE-DS node format: <Rx-fill Tx-cmpl Rx Tx Queue-base Queue-count> */
+			qcom,ppeds-map = <1 1 1 1 32 8>,		/* PPEDS Node#0 ring and queue map */
+							 <2 2 2 2 40 8>;		/* PPEDS Node#1 ring and queue map */
+			qcom,txdesc-map = <8 9 10 11>,			/* Port0 per-core Tx ring map */
+							  <12 13 14 15>,		/* MHT-Port1 per-core Tx ring map */
+							  <4 5 6 7>,			/* MHT-Port2 per-core Tx ring map/packets from  vp*/
+							  <16 17 18 19>,		/* MHT-Port3 per-core Tx ring map */
+							  <20 21 22 23>;		/* MHT-Port4 per-core Tx ring map */
+			qcom,txdesc-fc-grp-map = <1 2 3 4 5>;	/* Per GMAC flow control group map */
+			qcom,rxfill-map = <4 5 6 7>;			/* Per-core Rx fill ring map */
+			qcom,rxdesc-map = <12 13 14 15>;		/* Per-core Rx desc ring map */
+			qcom,rx-queue-start = <0>;				/* Rx queue start */
+			qcom,rx-ring-queue-map = <0 8 16 24>,	/* Priority 0 queues per-core Rx ring map */
+									 <1 9 17 25>,	/* Priority 1 queues per-core Rx ring map */
+									 <2 10 18 26>,	/* Priority 2 queues per-core Rx ring map */
+									 <3 11 19 27>,	/* Priority 3 queues per-core Rx ring map */
+									 <4 12 20 28>,	/* Priority 4 queues per-core Rx ring map */
+									 <5 13 21 29>,	/* Priority 5 queues per-core Rx ring map */
+									 <6 14 22 30>,	/* Priority 6 queues per-core Rx ring map */
+									 <7 15 23 31>;	/* Priority 7 queues per-core Rx ring map */
+			interrupts = <0 163 4>,					/* Tx complete ring id #4 IRQ info */
+						 <0 164 4>,					/* Tx complete ring id #5 IRQ info */
+						 <0 165 4>,					/* Tx complete ring id #6 IRQ info */
+						 <0 166 4>,					/* Tx complete ring id #7 IRQ info */
+						 <0 167 4>,					/* Tx complete ring id #8 IRQ info */
+						 <0 168 4>,					/* Tx complete ring id #9 IRQ info */
+						 <0 169 4>,					/* Tx complete ring id #10 IRQ info */
+						 <0 170 4>,					/* Tx complete ring id #11 IRQ info */
+						 <0 171 4>,					/* Tx complete ring id #12 IRQ info */
+						 <0 172 4>,					/* Tx complete ring id #13 IRQ info */
+						 <0 173 4>,					/* Tx complete ring id #14 IRQ info */
+						 <0 174 4>,					/* Tx complete ring id #15 IRQ info */
+						 <0 139 4>,					/* Rx desc ring id #12 IRQ info */
+						 <0 140 4>,					/* Rx desc ring id #13 IRQ info */
+						 <0 141 4>,					/* Rx desc ring id #14 IRQ info */
+						 <0 142 4>,					/* Rx desc ring id #15 IRQ info */
+						 <0 191 4>,					/* Misc error IRQ info */
+						 <0 155 4>,					/* RxFill ring id #4 IRQ info */
+						 <0 156 4>,					/* RxFill ring id #5 IRQ info */
+						 <0 157 4>,					/* RxFill ring id #6 IRQ info */
+						 <0 158 4>,					/* RxFill ring id #7 IRQ info */
+						 <0 160 4>,					/* PPEDS Node #1(TxComp ring id #1) TxComplete IRQ info */
+						 <0 128 4>,					/* PPEDS Node #1(Rx Desc ring id #1) Rx Desc IRQ info */
+						 <0 152 4>,					/* PPEDS Node #1(RxFill Desc ring id #1) Rx Fill IRQ info */
+						 <0 161 4>,					/* PPEDS Node #2(TxComp ring id #2) TxComplete IRQ info */
+						 <0 129 4>,					/* PPEDS Node #2(Rx Desc ring id #2) Rx Desc IRQ info */
+						 <0 153 4>,					/* PPEDS Node #2(RxFill Desc ring id #2) Rx Fill IRQ info */
+						 <0 175 4>,					/* MHT port Tx complete ring id #16 IRQ info */
+						 <0 176 4>,					/* MHT port Tx complete ring id #17 IRQ info */
+						 <0 177 4>,					/* MHT port Tx complete ring id #18 IRQ info */
+						 <0 178 4>,					/* MHT port Tx complete ring id #19 IRQ info */
+						 <0 179 4>,					/* MHT port Tx complete ring id #20 IRQ info */
+						 <0 180 4>,					/* MHT port Tx complete ring id #21 IRQ info */
+						 <0 181 4>,					/* MHT port Tx complete ring id #22 IRQ info */
+						 <0 182 4>;					/* MHT port Tx complete ring id #23 IRQ info */
+		};
+
+		leds {
+			compatible = "gpio-leds";
+
+			led_power_blue: led@34 {
+				label = "sys:blue";
+				gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+			led_power_green: led@35 {
+				label = "sys:green";
+				gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+			led_power_red: led@37 {
+				label = "sys:red";
+				gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&button_pins>;
+			pinctrl-names = "default";
+			button@1 {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&tlmm 24 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		wsi: wsi {
+			id = <0>;
+			num_chip = <2>;
+			status = "okay";
+			chip_info = <0 1 1>,
+						<1 1 0>;
+		};
+	};
+};
+
+&wifi0 {
+	led-gpio = <&tlmm 36 GPIO_ACTIVE_HIGH>;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,rproc_rpd = <&q6v5_wcss>;
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+	memory-region = <&q6_region>;
+	qcom,wsi = <&wsi>;
+	qcom,wsi_index = <0>;
+	qcom,board_id = <0x16>;
+	status = "okay";
+};
+
+&mhi_region1 {
+	status = "okay";
+};
+
+&qcn9224_pcie1 {
+	status = "okay";
+};
+
+/* QCN9224 5G+6G */
+&wifi4 {
+	hremote_node = <&qcn9224_pcie1>;
+	board_id = <0x1019>;
+	node_id = <0x1>;
+	status = "okay";
+};
+
+&blsp1_uart0 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_1_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&sdhc {
+	bus-width = <4>;
+	max-frequency = <192000000>;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-0 = <&sdc_default_state>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&xo {
+	clock-frequency = <24000000>;
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	pinctrl-0 = <&qspi_default_state>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nandcs@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+	};
+};
+
+&pcie1_phy_x2 {
+	status = "okay";
+};
+
+&pcie1 {
+	pinctrl-0 = <&pcie1_default_state>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	pcie1_rp {
+		reg = <0 0 0 0 0>;
+
+		qcom,mhi@1 {
+			reg = <0 0 0 0 0>;
+			boot-args = <0x2 0x4 0x34 0x3 0x0 0x0     /* MX Rail, GPIO52, Drive strength 0x3 */
+						 0x4 0x4 0x18 0x3 0x0 0x0     /* RFA1p2 Rail, GPIO24, Drive strength 0x3 */
+						 0x0 0x4 0x0 0x0 0x0 0x0>;    /* End of arguments */
+			memory-region = <&qcn9224_pcie1>;
+			qcom,wsi = <&wsi>;
+			qcom,wsi_index = <1>;
+			qcom,board_id = <0x1019>;
+		};
+	};
+};
+
+/* PINCTRL */
+
+&tlmm {
+	sdc_default_state: sdc-default-state {
+		clk-pins {
+			pins = "gpio13";
+			function = "sdc_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "gpio12";
+			function = "sdc_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "sdc_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	spi_0_data_clk_pins: spi-0-data-clk-state {
+		pins = "gpio14", "gpio15", "gpio16";
+		function = "blsp0_spi";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	spi_0_cs_pins: spi-0-cs-state {
+		pins = "gpio17";
+		function = "blsp0_spi";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	qspi_default_state: qspi-default-state {
+		qspi_clock {
+			pins = "gpio13";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		qspi_cs {
+			pins = "gpio12";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		qspi_data {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "qspi_data";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	serial_1_pins: serial1-pinmux { /*ble*/
+		pins = "gpio33", "gpio35";
+		function = "blsp1_uart2";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	button_pins: button-state {
+		pins = "gpio24";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	pcie1_default_state: pcie1-default-state {
+		pins = "gpio45";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+		output-low;
+	};
+};
+
+&license_manager {
+	status = "okay";
+};
+
+&usb3 {
+	qcom,multiplexed-phy;
+	status = "disabled";
+};
+
+&hs_m31phy_0 {
+	status = "okay";
+};
+
+&hs_m31phy_0 {
+	status = "okay";
+};
+
+&ssuniphy_0 {
+	status = "okay";
+};

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap7110c-341x.dts

@@ -31,6 +31,20 @@
 		stdout-path = "serial0";
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+	};
+
 	soc@0 {
 		mdio:mdio@90000 {
 			pinctrl-0 = <&mdio1_pins>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap750e-h.dts

@@ -190,6 +190,14 @@
 		/delete-node/ wcnss@4a900000;
 		/delete-node/ q6_caldb_region@4ce00000;
 
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
 		q6_mem_regions: q6_mem_regions@4A900000  {
 		        no-map;
 		        reg = <0x0 0x4A900000 0x0 0x5100000>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap750e-s.dts

@@ -190,6 +190,14 @@
 		/delete-node/ wcnss@4a900000;
 		/delete-node/ q6_caldb_region@4ce00000;
 
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
 		q6_mem_regions: q6_mem_regions@4A900000  {
 		        no-map;
 		        reg = <0x0 0x4A900000 0x0 0x5100000>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-sonicfi-rap750w-311a.dts

@@ -190,6 +190,14 @@
 		/delete-node/ wcnss@4a900000;
 		/delete-node/ q6_caldb_region@4ce00000;
 
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
 		q6_mem_regions: q6_mem_regions@4A900000  {
 		        no-map;
 		        reg = <0x0 0x4A900000 0x0 0x5100000>;

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-zyxel-nwa130be.dts

@@ -18,6 +18,21 @@
 	model = "Zyxel NWA130BE";
 	compatible = "zyxel,nwa130be", "qcom,ipq5332-ap-mi01.6", "qcom,ipq5332-rdp468", "qcom,ipq5332";
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			no-map;
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+	};
+
 	aliases {
 		serial0 = &blsp1_uart0;
 		serial1 = &blsp1_uart1;
@@ -128,6 +143,26 @@
 					blink_en = "enable";
 					active = "high";
 				};
+
+				qcom,port_ledinfo {
+					port@1 {
+						port = <2>;
+						led_source@0 {
+							source = <0>;
+							mode = "normal";
+							speed = "2500M";
+							active = "high";
+							blink_en = "enable";
+						};
+						led_source@1 {
+							source = <1>;
+							mode = "normal";
+							speed = "10M", "100M","1000M";
+							active = "high";
+							blink_en = "enable";
+						};
+					};
+				};
 			};
 
 			ess-switch1@1 {
@@ -164,6 +199,26 @@
 					};
 				};
 
+				qcom,port_ledinfo {
+					port@3 {
+						port = <3>;
+						led_source@0 {
+							source = <0>;
+							mode = "normal";
+							speed = "2500M";
+							active = "high";
+							blink_en = "enable";
+						};
+						led_source@1 {
+							source = <1>;
+							mode = "normal";
+							speed = "10M", "100M","1000M";
+							active = "high";
+							blink_en = "enable";
+						};
+					};
+				};
+
 				led_source@2 {
 					source = <2>;
 					mode = "normal";

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-zyxel-nwa50be.dts

@@ -0,0 +1,956 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ5332 RDP442 board device tree source
+ *
+ * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022-2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq5332.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "ipq5332-default-memory.dtsi"
+
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ5332/RDP442/AP-MI01.3";
+	compatible = "zyxel,nwa50be", "qcom,ipq5332-ap-mi01.3", "qcom,ipq5332-rdp442", "qcom,ipq5332";
+
+#ifdef __IPQ_MEM_PROFILE_512_MB__
+
+	/*     512M  Layout for IPQ5332 + QCN6432 + QCN6432
+	 * +==========+==============+========================+
+	 * |         |              |                         |
+	 * |  Region | Start Offset |          Size           |
+	 * |         |              |                         |
+	 * +---------+--------------+-------------------------+
+	 * |   Q6    |              |                         |
+	 * |  code/  |  0x4A900000  |          25MB           |
+	 * |  data   |              |                         |
+	 * +---------+--------------+-------------------------+
+	 * | IPQ5332 |              |                         |
+	 * |  data   |  0x4C200000  |          17MB           |
+	 * +---------+--------------+-------------------------+
+	 * | IPQ5332 |              |                         |
+	 * | M3 Dump |  0x4D300000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * | IPQ5332 |              |                         |
+	 * |  QDSS   |  0x4D400000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * | IPQ5332 |              |                         |
+	 * |  CALDB  |  0x4D500000  |           3MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_1|              |                         |
+	 * |  data   |  0x4D800000  |          16MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_1|              |                         |
+	 * | M3 Dump |  0x4E800000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_1|              |                         |
+	 * |  QDSS   |  0x4E900000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_1|              |                         |
+	 * |  CALDB  |  0x4EA00000  |           5MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_2|              |                         |
+	 * |  data   |  0x4EF00000  |          16MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_2|              |                         |
+	 * | M3 Dump |  0x4FF00000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_2|              |                         |
+	 * |  QDSS   |  0x50000000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_2|              |                         |
+	 * |  CALDB  |  0x50100000  |           5MB           |
+	 * +---------+--------------+-------------------------+
+	 * |         |              |                         |
+	 * |   MLO   |  0x50600000  |          12MB           |
+	 * +==================================================+
+	 * |                                                  |
+	 * |                                                  |
+	 * |                                                  |
+	 * |             Rest of memory for Linux             |
+	 * |                                                  |
+	 * |                                                  |
+	 * |                                                  |
+	 * +==================================================+
+	 */
+
+	reserved-memory {
+
+		/delete-node/ m3_dump@4cc00000;
+		/delete-node/ q6_etr_dump@1;
+		/delete-node/ mlo_global_mem_0@0x4db00000;
+		/delete-node/ wcnss@4a900000;
+		/delete-node/ q6_caldb_region@4ce00000;
+
+		q6_mem_regions: q6_mem_regions@4A900000  {
+			reg = <0x0 0x4a900000 0x0 0x5D00000>;
+			no-map;
+		};
+
+		q6_code_data: q6_code_data@4A900000 {
+			reg = <0x0 0x4a900000 0x0 0x1900000>;
+			no-map;
+		};
+
+		q6_ipq5332_data: q6_ipq5332_data@4C200000 {
+			reg = <0x0 0x4C200000 0x0 0x1100000>;
+			no-map;
+		};
+
+		m3_dump: m3_dump@4D300000 {
+			reg = <0x0 0x4D300000 0x0 0x100000>;
+			no-map;
+		};
+
+		q6_etr_region: q6_etr_dump@4D400000 {
+			reg = <0x0 0x4D400000 0x0 0x100000>;
+			no-map;
+		};
+
+		q6_ipq5332_caldb: q6_ipq5332_caldb@4D500000 {
+			reg = <0x0 0x4D500000 0x0 0x300000>;
+			no-map;
+		};
+
+		q6_qcn6432_data_1: q6_qcn6432_data_1@4D800000 {
+			reg = <0x0 0x4D800000 0x0 0x1000000>;
+			no-map;
+		};
+
+		m3_dump_qcn6432_1: m3_dump_qcn6432_1@4E800000 {
+			reg = <0x0 0x4E800000 0x0 0x100000>;
+			no-map;
+                };
+
+		q6_qcn6432_etr_1: q6_qcn6432_etr_1@4E900000 {
+			reg = <0x0 0x4E900000 0x0 0x100000>;
+			no-map;
+		};
+
+		q6_qcn6432_caldb_1: q6_qcn6432_caldb_1@4EA00000 {
+			reg = <0x0 0x4EA00000 0x0 0x500000>;
+			no-map;
+		};
+
+		q6_qcn6432_data_2: q6_qcn6432_data_2@4EF00000 {
+			reg = <0x0 0x4EF00000 0x0 0x1000000>;
+			no-map;
+		};
+
+		m3_dump_qcn6432_2: m3_dump_qcn6432_2@4FF00000 {
+			reg = <0x0 0x4FF00000 0x0 0x100000>;
+			no-map;
+                };
+
+		q6_qcn6432_etr_2: q6_qcn6432_etr_2@50000000 {
+			reg = <0x0 0x50000000 0x0 0x100000>;
+			no-map;
+		};
+
+		q6_qcn6432_caldb_2: q6_qcn6432_caldb_2@50100000 {
+			reg = <0x0 0x50100000 0x0 0x500000>;
+			no-map;
+		};
+
+		mlo_global_mem0: mlo_global_mem_0@50600000 {
+			reg = <0x0 0x50600000 0x0 0xC00000>;
+			no-map;
+		};
+	};
+#else
+
+	/*  1G  Layout for IPQ5332 + QCN6432 + QCN6432
+	* +==========+==============+========================+
+	* |         |              |                         |
+	* |  Region | Start Offset |          Size           |
+	* |         |              |                         |
+	* +---------+--------------+-------------------------+
+	* |   Q6    |              |                         |
+	* |  code/  |  0x4A900000  |          25MB           |
+	* |  data   |              |                         |
+	* +---------+--------------+-------------------------+
+	* | IPQ5332 |              |                         |
+	* |  data   |  0x4C200000  |          21MB           |
+	* +---------+--------------+-------------------------+
+	* | IPQ5332 |              |                         |
+	* | M3 Dump |  0x4D700000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* | IPQ5332 |              |                         |
+	* |  QDSS   |  0x4D800000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* | IPQ5332 |              |                         |
+	* |  CALDB  |  0x4D900000  |           5MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_1|              |                         |
+	* |  data   |  0x4DE00000  |          21MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_1|              |                         |
+	* | M3 Dump |  0x4F300000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_1|              |                         |
+	* |  QDSS   |  0x4F400000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_1|              |                         |
+	* |  CALDB  |  0x4F500000  |           5MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_2|              |                         |
+	* |  data   |  0x4FA00000  |          21MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_2|              |                         |
+	* | M3 Dump |  0x50F00000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_2|              |                         |
+	* |  QDSS   |  0x51000000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_2|              |                         |
+	* |  CALDB  |  0x51100000  |           5MB           |
+	* +---------+--------------+-------------------------+
+	* |         |              |                         |
+	* |   MLO   |  0x51600000  |          12MB           |
+	* +==================================================+
+	* |                                                  |
+	* |                                                  |
+	* |                                                  |
+	* |             Rest of memory for Linux             |
+	* |                                                  |
+	* |                                                  |
+	* |                                                  |
+	* +==================================================+
+	*/
+	reserved-memory {
+
+		/delete-node/ m3_dump@4cc00000;
+		/delete-node/ q6_etr_dump@1;
+		/delete-node/ mlo_global_mem_0@0x4db00000;
+		/delete-node/ wcnss@4a900000;
+		/delete-node/ q6_caldb_region@4ce00000;
+
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
+		q6_mem_regions: q6_mem_regions@4A900000  {
+			no-map;
+			reg = <0x0 0x4a900000 0x0 0x6D00000>;
+		};
+
+		q6_code_data: q6_code_data@4A900000 {
+			no-map;
+			reg = <0x0 0x4a900000 0x0 0x1900000>;
+		};
+
+		q6_ipq5332_data: q6_ipq5332_data@4C200000 {
+			no-map;
+			reg = <0x0 0x4C200000 0x0 0x1500000>;
+		};
+
+		m3_dump: m3_dump@4D700000 {
+			no-map;
+			reg = <0x0 0x4D700000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D800000 {
+			no-map;
+			reg = <0x0 0x4D800000 0x0 0x100000>;
+		};
+
+		q6_ipq5332_caldb: q6_ipq5332_caldb@4D900000 {
+			no-map;
+			reg = <0x0 0x4D900000 0x0 0x500000>;
+		};
+
+		q6_qcn6432_data_1: q6_qcn6432_data_1@4DE00000 {
+			no-map;
+			reg = <0x0 0x4DE00000 0x0 0x1500000>;
+		};
+
+		m3_dump_qcn6432_1: m3_dump_qcn6432_1@4F300000 {
+			no-map;
+			reg = <0x0 0x4F300000 0x0 0x100000>;
+        };
+
+		q6_qcn6432_etr_1: q6_qcn6432_etr_1@4F400000 {
+			no-map;
+			reg = <0x0 0x4F400000 0x0 0x100000>;
+		};
+
+		q6_qcn6432_caldb_1: q6_qcn6432_caldb_1@4F500000 {
+			no-map;
+			reg = <0x0 0x4F500000 0x0 0x500000>;
+		};
+
+		q6_qcn6432_data_2: q6_qcn6432_data_2@4FA00000 {
+			no-map;
+			reg = <0x0 0x4FA00000 0x0 0x1500000>;
+		};
+
+		m3_dump_qcn6432_2: m3_dump_qcn6432_2@50F00000 {
+			no-map;
+			reg = <0x0 0x50F00000 0x0 0x100000>;
+		};
+
+		q6_qcn6432_etr_2: q6_qcn6432_etr_2@51000000 {
+			no-map;
+			reg = <0x0 0x51000000 0x0 0x100000>;
+		};
+
+		q6_qcn6432_caldb_2: q6_qcn6432_caldb_2@51100000 {
+			no-map;
+			reg = <0x0 0x51100000 0x0 0x500000>;
+		};
+
+		mlo_global_mem0: mlo_global_mem_0@51600000 {
+			no-map;
+			reg = <0x0 0x51600000 0x0 0xC00000>;
+		};
+	};
+#endif
+
+	aliases {
+		serial0 = &blsp1_uart0;
+		serial1 = &blsp1_uart1;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc@0 {
+		mdio:mdio@90000 {
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			/*gpio22 is for wan napa, gpio51 for lan napa*/
+			phy-reset-gpio = <&tlmm 51 GPIO_ACTIVE_LOW>;
+			status = "okay";
+
+			phy2: ethernet-phy@2 {
+				reg = <28>;
+			};
+		};
+
+		leds {
+			compatible = "gpio-leds";
+			pinctrl-0 = <&led_pins>;
+			pinctrl-names = "default";
+			led_blue{
+				label = "led_blue";
+				gpio = <&tlmm 22 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "led_blue";
+				default-state = "off";
+			};
+			led_green {
+				label = "led_green";
+				gpio = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "led_green";
+				default-state = "on";
+			};
+			led_white {
+				label = "led_white";
+				gpio = <&tlmm 43 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "led_white";
+				default-state = "off";
+			};
+			led_red {
+				label = "led_red";
+				gpio = <&tlmm 44 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "led_red";
+				default-state = "off";
+			};
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&button_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+
+			button@1 {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		ess-instance {
+			ess-switch@3a000000 {
+				switch_cpu_bmp = <0x1>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x4>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>; /* wan port bitmap */
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance0*/
+				switch_mac_mode1 = <0xc>; /* mac mode for uniphy instance1*/
+				switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <2>;
+						phy_address = <28>;
+					};
+				};
+				qcom,port_ledinfo {
+					port@0 {
+						port = <2>;
+						led_source@0 {
+							source = <0>;
+							mode = "normal";
+							speed = "2500M";
+							active = "high";
+							blink_en = "enable";
+						};
+						led_source@1 {
+							source = <1>;
+							mode = "normal";
+							speed = "10M", "100M","1000M";
+							active = "high";
+							blink_en = "enable";
+						};
+					};
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			qcom,id = <2>;
+			reg = <0x3a504000 0x4000>;
+			qcom,mactype = <1>;
+			local-mac-address = [000000000000];
+			mdio-bus = <&mdio>;
+			qcom,phy-mdio-addr = <28>;
+			qcom,link-poll = <1>;
+			phy-mode = "sgmii";
+		};
+
+		nss-macsec0 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <28>;
+			mdiobus = <&mdio>;
+		};
+
+		/* EDMA host driver configuration for the board */
+		edma@3ab00000 {
+			qcom,txdesc-ring-start = <4>;		/* Tx desc ring start ID */
+			qcom,txdesc-rings = <12>;		/* Total number of Tx desc rings to be provisioned */
+			qcom,mht-txdesc-rings = <8>;            /* Extra Tx desc rings to be provisioned for MHT SW ports */
+			qcom,txcmpl-ring-start = <4>;		/* Tx complete ring start ID */
+			qcom,txcmpl-rings = <12>;		/* Total number of Tx complete rings to be provisioned */
+			qcom,mht-txcmpl-rings = <8>;            /* Extra Tx complete rings to be provisioned for mht sw ports. */
+			qcom,rxfill-ring-start = <4>;		/* Rx fill ring start ID */
+			qcom,rxfill-rings = <4>;		/* Total number of Rx fill rings to be provisioned */
+			qcom,rxdesc-ring-start = <12>;		/* Rx desc ring start ID */
+			qcom,rxdesc-rings = <4>;		/* Total number of Rx desc rings to be provisioned */
+			qcom,rx-page-mode = <0>;		/* Rx fill ring page mode */
+			qcom,tx-map-priority-level = <1>;	/* Tx priority level per port */
+			qcom,rx-map-priority-level = <1>;	/* Rx priority level per core */
+			qcom,ppeds-num = <2>;			/* Number of PPEDS nodes */
+			/* PPE-DS node format: <Rx-fill Tx-cmpl Rx Tx Queue-base Queue-count> */
+			qcom,ppeds-map = <1 1 1 1 32 8>,	/* PPEDS Node#0 ring and queue map */
+					<2 2 2 2 40 8>;		/* PPEDS Node#1 ring and queue map */
+			qcom,txdesc-map = <8 9 10 11>,		/* Port0 per-core Tx ring map */
+					<12 13 14 15>,        /* MHT-Port1 per-core Tx ring map */
+					<4 5 6 7>,            /* MHT-Port2 per-core Tx ring map/packets from  vp*/
+					<16 17 18 19>,        /* MHT-Port3 per-core Tx ring map */
+					<20 21 22 23>;        /* MHT-Port4 per-core Tx ring map */
+			qcom,txdesc-fc-grp-map = <1 2 3 4 5>;   /* Per GMAC flow control group map */
+			qcom,rxfill-map = <4 5 6 7>;		/* Per-core Rx fill ring map */
+			qcom,rxdesc-map = <12 13 14 15>;	/* Per-core Rx desc ring map */
+			qcom,rx-queue-start = <0>;		/* Rx queue start */
+			qcom,rx-ring-queue-map = <0 8 16 24>,	/* Priority 0 queues per-core Rx ring map */
+						<1 9 17 25>,	/* Priority 1 queues per-core Rx ring map */
+						<2 10 18 26>,	/* Priority 2 queues per-core Rx ring map */
+						<3 11 19 27>,	/* Priority 3 queues per-core Rx ring map */
+						<4 12 20 28>,	/* Priority 4 queues per-core Rx ring map */
+						<5 13 21 29>,	/* Priority 5 queues per-core Rx ring map */
+						<6 14 22 30>,	/* Priority 6 queues per-core Rx ring map */
+						<7 15 23 31>;	/* Priority 7 queues per-core Rx ring map */
+			interrupts = <0 163 4>,			/* Tx complete ring id #4 IRQ info */
+				   <0 164 4>,			/* Tx complete ring id #5 IRQ info */
+				   <0 165 4>,			/* Tx complete ring id #6 IRQ info */
+				   <0 166 4>,			/* Tx complete ring id #7 IRQ info */
+				   <0 167 4>,			/* Tx complete ring id #8 IRQ info */
+				   <0 168 4>,			/* Tx complete ring id #9 IRQ info */
+				   <0 169 4>,			/* Tx complete ring id #10 IRQ info */
+				   <0 170 4>,			/* Tx complete ring id #11 IRQ info */
+				   <0 171 4>,			/* Tx complete ring id #12 IRQ info */
+				   <0 172 4>,			/* Tx complete ring id #13 IRQ info */
+				   <0 173 4>,			/* Tx complete ring id #14 IRQ info */
+				   <0 174 4>,			/* Tx complete ring id #15 IRQ info */
+				   <0 139 4>,			/* Rx desc ring id #12 IRQ info */
+				   <0 140 4>,			/* Rx desc ring id #13 IRQ info */
+				   <0 141 4>,			/* Rx desc ring id #14 IRQ info */
+				   <0 142 4>,			/* Rx desc ring id #15 IRQ info */
+				   <0 191 4>,			/* Misc error IRQ info */
+				<0 160 4>,			/* PPEDS Node #1(TxComp ring id #1) TxComplete IRQ info */
+				<0 128 4>,			/* PPEDS Node #1(Rx Desc ring id #1) Rx Desc IRQ info */
+				<0 152 4>,			/* PPEDS Node #1(RxFill Desc ring id #1) Rx Fill IRQ info */
+				<0 161 4>,			/* PPEDS Node #2(TxComp ring id #2) TxComplete IRQ info */
+				<0 129 4>,			/* PPEDS Node #2(Rx Desc ring id #2) Rx Desc IRQ info */
+				<0 153 4>,                      /* PPEDS Node #2(RxFill Desc ring id #2) Rx Fill IRQ info */
+				<0 175 4>,                   /* MHT port Tx complete ring id #16 IRQ info */
+				<0 176 4>,                   /* MHT port Tx complete ring id #17 IRQ info */
+				<0 177 4>,                   /* MHT port Tx complete ring id #18 IRQ info */
+				<0 178 4>,                   /* MHT port Tx complete ring id #19 IRQ info */
+				<0 179 4>,                   /* MHT port Tx complete ring id #20 IRQ info */
+				<0 180 4>,                   /* MHT port Tx complete ring id #21 IRQ info */
+				<0 181 4>,                   /* MHT port Tx complete ring id #22 IRQ info */
+				<0 182 4>;                   /* MHT port Tx complete ring id #23 IRQ info */
+		};
+
+		wsi: wsi {
+			id = <0>;
+			num_chip = <2>;
+			chip_info = <0 1 1>,
+				    <1 1 0>;
+		};
+
+		q6v5_wcss: remoteproc@d100000 {
+			boot-args = <0x1 0x4 0x3 0x0 0x26 0x2>,
+					<0x1 0x4 0x4 0x1 0x2f 0x2>;
+			memory-region = <&q6_mem_regions>;
+
+			/delete-node/ remoteproc_pd1;
+			/delete-node/ remoteproc_pd2;
+			/delete-node/ remoteproc_pd3;
+
+			q6_wcss_pd4: remoteproc_pd4 {
+				compatible = "qcom,ipq5332-mpd-upd-text";
+				firmware = "IPQ5332/q6_fw4.mdt";
+
+				q6_wcss_pd1: remoteproc_pd1 {
+					compatible = "qcom,ipq5332-wcss-ahb-mpd";
+					firmware = "IPQ5332/q6_fw1.mdt";
+					m3_firmware = "IPQ5332/iu_fw.mdt";
+					interrupts-extended = <&wcss_smp2p_in 8 0>,
+							<&wcss_smp2p_in 9 0>,
+							<&wcss_smp2p_in 12 0>,
+							<&wcss_smp2p_in 11 0>;
+					interrupt-names = "fatal",
+							"ready",
+							"spawn-ack",
+							"stop-ack";
+
+					qcom,smem-states = <&wcss_smp2p_out 8>,
+							<&wcss_smp2p_out 9>,
+							<&wcss_smp2p_out 10>;
+					qcom,smem-state-names = "shutdown",
+								"stop",
+								"spawn";
+					memory-region = <&q6_ipq5332_data>,
+							<&m3_dump>,
+							<&q6_etr_region>,
+							<&q6_ipq5332_caldb>;
+				};
+
+				q6_wcss_pd2: remoteproc_pd2 {
+					compatible = "qcom,ipq5332-wcss-pcie-mpd";
+					firmware = "IPQ5332/q6_fw2.mdt";
+					m3_firmware = "qcn6432/iu_fw.mdt";
+					interrupts-extended = <&wcss_smp2p_in 16 0>,
+							<&wcss_smp2p_in 17 0>,
+							<&wcss_smp2p_in 20 0>,
+							<&wcss_smp2p_in 19 0>;
+					interrupt-names = "fatal",
+							"ready",
+							"spawn-ack",
+							"stop-ack";
+
+					qcom,smem-states = <&wcss_smp2p_out 16>,
+							<&wcss_smp2p_out 17>,
+							<&wcss_smp2p_out 18>;
+					qcom,smem-state-names = "shutdown",
+								"stop",
+								"spawn";
+					memory-region = <&q6_qcn6432_data_1>,
+							<&m3_dump_qcn6432_1>,
+							<&q6_qcn6432_etr_1>,
+							<&q6_qcn6432_caldb_1>;
+					status = "okay";
+				};
+
+				q6_wcss_pd3: remoteproc_pd3 {
+					compatible = "qcom,ipq5332-wcss-pcie-mpd";
+					firmware = "IPQ5332/q6_fw3.mdt";
+					interrupts-extended = <&wcss_smp2p_in 24 0>,
+							<&wcss_smp2p_in 25 0>,
+							<&wcss_smp2p_in 28 0>,
+							<&wcss_smp2p_in 27 0>;
+					interrupt-names = "fatal",
+							"ready",
+							"spawn-ack",
+							"stop-ack";
+
+					qcom,smem-states = <&wcss_smp2p_out 24>,
+							<&wcss_smp2p_out 25>,
+							<&wcss_smp2p_out 26>;
+					qcom,smem-state-names = "shutdown",
+								"stop",
+								"spawn";
+					memory-region = <&q6_qcn6432_data_2>,
+							<&m3_dump_qcn6432_2>,
+							<&q6_qcn6432_etr_2>,
+							<&q6_qcn6432_caldb_2>;
+					status = "okay";
+				};
+			};
+		};
+	};
+};
+
+&blsp1_uart0 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&blsp1_uart1 {
+        pinctrl-0 = <&serial_1_pins>;
+        pinctrl-names = "default";
+        status = "disabled";
+};
+
+&blsp1_i2c1 {
+	clock-frequency  = <400000>;
+	pinctrl-0 = <&i2c_1_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&blsp1_spi0 {
+	pinctrl-0 = <&spi_0_data_clk_pins &spi_0_cs_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "n25q128a11", "micron,n25q128a11", "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&sdhc {
+	bus-width = <4>;
+	max-frequency = <192000000>;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-0 = <&sdc_default_state>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&xo {
+	clock-frequency = <24000000>;
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	pinctrl-0 = <&qspi_default_state>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nandcs@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+	};
+};
+
+/* PINCTRL */
+
+&tlmm {
+
+	led_pins: led_pins {
+		board_info {
+			pins = "gpio2", "gpio3";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			input-enable;
+		};
+
+		apd_dc_in {
+			pins = "gpio24";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down; //Adapter un-plug
+			input-enable;
+		};
+
+		poe_status {
+			pins = "gpio34";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up; //AF
+			input-enable;
+		};
+
+		/* To MR pin */
+		rst_mb {
+			pins = "gpio29";
+			function = "gpio";
+			drive-strength = <8>;
+			output-high;
+		};
+
+		led_blue {
+			pins = "gpio22";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_green {
+			pins = "gpio45";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_white {
+			pins = "gpio43";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_red {
+			pins = "gpio44";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	qspi_default_state: qspi-default-state {
+		qspi_clock {
+			pins = "gpio13";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		qspi_cs {
+			pins = "gpio12";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		qspi_data {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "qspi_data";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	serial_1_pins: serial1-pinmux {
+		pins = "gpio33", "gpio34", "gpio35", "gpio36";
+		function = "blsp1_uart2";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	i2c_1_pins: i2c-1-state {
+		pins = "gpio29", "gpio30";
+		function = "blsp1_i2c0";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	button_pins: button-state {
+		pins = "gpio35";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	pwm_pins: pwm-state {
+		pins = "gpio46";
+		function = "pwm0";
+		drive-strength = <8>;
+	};
+
+	sdc_default_state: sdc-default-state {
+		clk-pins {
+			pins = "gpio13";
+			function = "sdc_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "gpio12";
+			function = "sdc_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "sdc_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	spi_0_data_clk_pins: spi-0-data-clk-state {
+		pins = "gpio14", "gpio15", "gpio16";
+		function = "blsp0_spi";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	spi_0_cs_pins: spi-0-cs-state {
+		pins = "gpio17";
+		function = "blsp0_spi";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	mdio1_pins: mdio1-state {
+		mux_0 {
+			pins = "gpio27";
+			function = "mdc1";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+		mux_1 {
+			pins = "gpio28";
+			function = "mdio1";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&license_manager {
+	status = "okay";
+};
+
+&usb3 {
+	qcom,select-utmi-as-pipe-clk;
+	status = "okay";
+
+	dwc3@8a00000 {
+		/delete-property/ #phy-cells;
+		/delete-property/ phys;
+		/delete-property/ phy-names;
+	};
+};
+
+&pwm {
+	pinctrl-0 = <&pwm_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&hs_m31phy_0 {
+	status = "okay";
+};
+
+&wifi0 {
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,rproc_rpd = <&q6v5_wcss>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+	qcom,bdf-addr = <0x4C200000 0x4C200000 0x4C200000 0x0 0x0 0x0>;
+	qcom,caldb-addr = <0x4D900000 0x4D500000 0x0 0x0 0x0 0x0>;
+#ifdef __IPQ_MEM_PROFILE_512_MB__
+	qcom,tgt-mem-mode = <1>;
+	qcom,caldb-size = <0x300000>;
+#else
+	qcom,tgt-mem-mode = <0>;
+	qcom,caldb-size = <0x500000>;
+#endif
+	qcom,board_id = <0x12>;
+#if defined(__CNSS2__)
+	mem-region = <&q6_ipq5332_data>;
+#else
+	memory-region = <&q6_ipq5332_data>;
+#endif
+	qcom,wsi = <&wsi>;
+	qcom,wsi_index = <0>;
+	status = "okay";
+};
+
+&wifi1 {
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd2>;
+	qcom,rproc_rpd = <&q6v5_wcss>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
+	qcom,bdf-addr = <0x4DE00000 0x4D800000 0x0 0x0 0x0 0x0>;
+	qcom,caldb-addr = <0x4F500000 0x4EA00000 0x0 0x0 0x0 0x0>;
+	qcom,umac-irq-reset-addr = <0x20000884>;
+	qcom,caldb-size = <0x500000>;
+#ifdef __IPQ_MEM_PROFILE_512_MB__
+	qcom,tgt-mem-mode = <1>;
+#else
+	qcom,tgt-mem-mode = <0>;
+#endif
+	qcom,board_id = <0x060>;
+#if defined(__CNSS2__)
+	mem-region = <&q6_qcn6432_data_1>;
+#else
+	memory-region = <&q6_qcn6432_data_1>;
+#endif
+	qcom,wsi = <&wsi>;
+	qcom,wsi_index = <1>;
+	status = "disabled";
+	interrupts = <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "umac_reset";
+};
+
+&wifi2 {
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd3>;
+	qcom,rproc_rpd = <&q6v5_wcss>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
+	qcom,bdf-addr = <0x4FA00000 0x4EF00000 0x4FA00000 0x0 0x0 0x0>;
+	qcom,caldb-addr = <0x51100000 0x50100000 0x51100000 0x0 0x0 0x0>;
+	qcom,umac-irq-reset-addr = <0x18000884>;
+	qcom,caldb-size = <0x500000>;
+#ifdef __IPQ_MEM_PROFILE_512_MB__
+	qcom,tgt-mem-mode = <1>;
+#else
+	qcom,tgt-mem-mode = <0>;
+#endif
+	qcom,board_id = <0x070>;
+#if defined(__CNSS2__)
+	mem-region = <&q6_qcn6432_data_2>;
+#else
+	memory-region = <&q6_qcn6432_data_2>;
+#endif
+	qcom,wsi = <&wsi>;
+	qcom,wsi_index = <1>;
+	qcom,wide_band = <1>;
+	status = "okay";
+	interrupts = <GIC_SPI 410 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "umac_reset";
+};

feeds/qca-wifi-7/ipq53xx/image/ipq53xx.mk

@@ -52,6 +52,19 @@ define Device/edgecore_eap105
 endef
 TARGET_DEVICES += edgecore_eap105
 
+define Device/emplus_wap7635
+  DEVICE_TITLE := EMPLUS WAP7635
+  DEVICE_DTS := ipq5332-emplus-wap7635
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_DTS_CONFIG := config@mi01.6
+  IMAGES := sysupgrade.tar nand-factory.bin nand-factory.ubi
+  IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
+  IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
+  IMAGE/nand-factory.ubi := append-ubi
+  DEVICE_PACKAGES := ath12k-wifi-emplus-wap7635 ath12k-firmware-qcn92xx ath12k-firmware-ipq5332
+endef
+TARGET_DEVICES += emplus_wap7635
+
 define Device/sonicfi_rap7110c_341x
   DEVICE_TITLE := SONICFI RAP7110C-341X
   DEVICE_DTS := ipq5332-sonicfi-rap7110c-341x
@@ -149,6 +162,22 @@ define Device/zyxel_nwa130be
 endef
 TARGET_DEVICES += zyxel_nwa130be
 
+
+define Device/zyxel_nwa50be
+  DEVICE_TITLE := Zyxel NWA50BE
+  DEVICE_DTS := ipq5332-zyxel-nwa50be
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_DTS_CONFIG := config@mi01.3
+  IMAGES := sysupgrade.tar nand-factory.bin nand-factory.ubi
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
+  IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
+  IMAGE/nand-factory.ubi := append-ubi
+  DEVICE_PACKAGES := ath12k-wifi-zyxel-nwa50be ath12k-firmware-ipq5332-peb-peb -ath12k-firmware-qcn92xx
+endef
+TARGET_DEVICES += zyxel_nwa50be
+
 define Device/cig_wf672
   DEVICE_TITLE := CIG WF672
   DEVICE_DTS := ipq5332-cig-wf672

feeds/qca-wifi-7/ipq53xx/patches-6.1/0660-add-IPQ_MEM_PROFILE-in-arm64-kconfig.patch

@@ -0,0 +1,33 @@
+From f7b27331b915477cd289c37b56efb0d28b2d6f38 Mon Sep 17 00:00:00 2001
+From: Antonio Wu <antonio.wu@cybertan.com.tw>
+Date: Tue, 5 Aug 2025 10:39:58 +0000
+Subject: [PATCH] Add IPQ_MEM_PROFILE in arm64 kconfig
+
+---
+ arch/arm64/Kconfig | 10 ++++++++++
+ 1 file changed, 10 insertions(+)
+
+diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
+index 702a289..7864e79 100644
+--- a/arch/arm64/Kconfig
++++ b/arch/arm64/Kconfig
+@@ -2143,6 +2143,16 @@ config STACKPROTECTOR_PER_TASK
+ 	def_bool y
+ 	depends on STACKPROTECTOR && CC_HAVE_STACKPROTECTOR_SYSREG
+ 
++config IPQ_MEM_PROFILE
++	int "Select Memory Profile"
++	range 0 1024
++	default 0
++	help
++	  This option select memory profile to be used, which defines
++	  the reserved memory configuration used in device tree.
++
++	  If unsure, say 0
++
+ # The GPIO number here must be sorted by descending number. In case of
+ # a multiplatform kernel, we just want the highest value required by the
+ # selected platforms.
+-- 
+2.17.1
+

feeds/qca-wifi-7/mac80211/patches-sonicfi_rap7110c_341x/ath12k/0001-sonicfi_rap7110c-341x-therlaml-setting.patch

@@ -0,0 +1,63 @@
+Index: backports-6.5-rc3/drivers/net/wireless/ath/ath12k/thermal.h
+===================================================================
+--- backports-6.5-rc3.orig/drivers/net/wireless/ath/ath12k/thermal.h
++++ backports-6.5-rc3/drivers/net/wireless/ath/ath12k/thermal.h
+@@ -13,35 +13,35 @@
+ 
+ /* Below temperatures are in celsius */
+ #define ATH12K_THERMAL_LVL0_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 110
+-#define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 105
+-#define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 110
++#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 115
++#define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 125
+ 
+ #define ATH12K_THERMAL_LVL0_V2_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 95
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 90
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 110
+-#define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 100
++#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 110
++#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 110
+ #define ATH12K_THERMAL_LVL4_V2_TEMP_HIGH_MARK 120
+ 
+ #define ATH12K_THERMAL_LVL0_DUTY_CYCLE 0
+-#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 50
+-#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 90
+-#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 100
++#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 30
++#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 50
++#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 70
+ 
+-#define ATH12K_THERMAL_LVL0_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL4_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL0_V2_DUTY_CYCLE 0
++#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE 20
++#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE 40
++#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE 80
++#define ATH12K_THERMAL_LVL4_V2_DUTY_CYCLE 100
+ 
+ #define THERMAL_CONFIG_POUT0                        0
+ #define THERMAL_CONFIG_POUT1                        12

feeds/qca-wifi-7/mac80211/patches-sonicfi_rap750w_311a/ath12k/0001-sonicfi-rap750w-311a-thermal-setting.patch

@@ -0,0 +1,57 @@
+--- a/drivers/net/wireless/ath/ath12k/thermal.h
++++ b/drivers/net/wireless/ath/ath12k/thermal.h
+@@ -13,34 +13,34 @@
+ 
+ /* Below temperatures are in celsius */
+ #define ATH12K_THERMAL_LVL0_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 110
+-#define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 100
++#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 110
+ #define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 120
+ 
+ #define ATH12K_THERMAL_LVL0_V2_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 95
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 90
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 110
+-#define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 100
++#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 110
++#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 110
+ #define ATH12K_THERMAL_LVL4_V2_TEMP_HIGH_MARK 120
+ 
+ #define ATH12K_THERMAL_LVL0_DUTY_CYCLE 0
+-#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 50
+-#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 90
+-#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 100
++#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 30
++#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 50
++#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 70
+ 
+ #define ATH12K_THERMAL_LVL0_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
+ #define ATH12K_THERMAL_LVL4_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
+ 
+ #define THERMAL_CONFIG_POUT0                        0

feeds/qca-wifi-7/mac80211/patches-zyxel_nwa50be/ath12k/0001-thermal-thermal-setting.patch

@@ -0,0 +1,74 @@
+From 357da3320f8bcad056b905fb85cad3a29c343d31 Mon Sep 17 00:00:00 2001
+From: YenLin Pan <yenlin.pan@zyxel.com.tw>
+Date: Tue, 12 Aug 2025 15:41:39 +0800
+Subject: [PATCH] thermal: thermal setting
+
+lo0 -100 -hi0 105 -off0 0
+lo1 95 -hi1 110 -off1 20
+lo2 100 -hi2 115 -off2 60
+lo3 105 -hi3 119 -off3 98
+
+Signed-off-by: YenLin Pan <YenLin.Pan@zyxel.com.tw>
+---
+ drivers/net/wireless/ath/ath12k/thermal.h | 34 +++++++++++------------
+ 1 file changed, 17 insertions(+), 17 deletions(-)
+
+diff --git a/drivers/net/wireless/ath/ath12k/thermal.h b/drivers/net/wireless/ath/ath12k/thermal.h
+index 5c91906..e81f9a4 100644
+--- a/drivers/net/wireless/ath/ath12k/thermal.h
++++ b/drivers/net/wireless/ath/ath12k/thermal.h
+@@ -13,34 +13,34 @@
+ 
+ /* Below temperatures are in celsius */
+ #define ATH12K_THERMAL_LVL0_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 100
++#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 105
+ #define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 110
+ #define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 115
+ #define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 105
+-#define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 119
+ 
+ #define ATH12K_THERMAL_LVL0_V2_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 95
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 90
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 95
++#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 100
++#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 119
+ #define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 105
+ #define ATH12K_THERMAL_LVL4_V2_TEMP_HIGH_MARK 120
+ 
+ #define ATH12K_THERMAL_LVL0_DUTY_CYCLE 0
+-#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 50
+-#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 90
+-#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 100
++#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 20
++#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 60
++#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 98
+ 
+ #define ATH12K_THERMAL_LVL0_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
+ #define ATH12K_THERMAL_LVL4_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
+ 
+ #define THERMAL_CONFIG_POUT0                        0
+-- 
+2.34.1
+

feeds/qca-wifi-7/qca-ssdk-qca/Makefile

@@ -100,6 +100,7 @@ endif
 ifdef CONFIG_TARGET_PROFILE
 TARGET_PROFILE=$(subst ",,$(CONFIG_TARGET_PROFILE))
 PATCH_PROFILE_NAME=patches-$(subst DEVICE_,,$(TARGET_PROFILE))
+FILES_PROFILE_NAME=files-$(subst DEVICE_,,$(TARGET_PROFILE))
 endif
 
 QCASSDK_CONFIG_OPTS+= TOOL_PATH=$(TOOLCHAIN_BIN_PATH) \
@@ -202,6 +203,15 @@ define patch_profile
 	$(call PatchDir/Default,$(PKG_BUILD_DIR),./$(PATCH_PROFILE_NAME))
 endef
 
+define files_profile
+
+	if [ -d "./$(FILES_PROFILE_NAME)" ]; then \
+		$(CP) ./$(FILES_PROFILE_NAME)/* ./files/ ; \
+	fi
+endef
+
 Hooks/Prepare/Post += patch_profile
+Hooks/Prepare/Post += files_profile
+
 $(eval $(call KernelPackage,qca-ssdk-qca-nohnat))
 $(eval $(call KernelPackage,qca-ssdk-qca-hnat))

feeds/qca-wifi-7/qca-ssdk-qca/files-zyxel_nwa130be/qca-ssdk

@@ -0,0 +1,317 @@
+#!/bin/sh /etc/rc.common
+# Copyright (c) 2018, 2021, The Linux Foundation. All rights reserved.
+# Copyright (c) 2022-2024, Qualcomm Innovation Center, Inc. All rights reserved.
+#
+# Permission to use, copy, modify, and/or distribute this software for any
+# purpose with or without fee is hereby granted, provided that the above
+# copyright notice and this permission notice appear in all copies.
+#
+# THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+# WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+# MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+# ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+# WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+# ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+# OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+#
+
+START=16
+
+#!/bin/sh
+ruletype="ip4 ip6"
+side="wan lan"
+qwan="1 3 2 0 5 7 6 4"
+qlan="0 1 2 3 4 5 6 7"
+
+function create_war_acl_rules(){
+	for lw in $side
+	do
+		#echo $lw
+		if [ "$lw" == "wan" ];then
+			listid=254
+			queue=$qwan
+			portmap=0x20
+		else
+			listid=255
+			queue=$qlan
+			portmap=0x1e
+		fi
+		#echo $queue
+		#echo "creating list $listid"
+		ssdk_sh acl list create $listid 255
+		ruleid=0
+		for rt in $ruletype
+		do
+			for qid in $queue
+			do
+				cmd="ssdk_sh acl rule add $listid $ruleid  1 n 0 0"
+				#echo $cmd
+				if [ "$rt" == "ip4" ];then
+					cmd="$cmd ip4 n n n n n n n n n n n n n n n n n n n n n n n n n n n n n"
+					#echo $cmd
+				else
+					cmd="$cmd ip6 n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n"
+					#echo $cmd
+				fi
+				if [ $ruleid -le 3 ];then
+					#non-zero dscp
+					cmd="$cmd y 0x0 0xff"
+				elif [ $ruleid -le 7 ];then
+					#zero dscp
+					cmd="$cmd n"
+				elif [ $ruleid -le 11 ];then
+					#non-zero dscp
+					cmd="$cmd y 0x0 0xff"
+				else
+					#zero dscp
+					cmd="$cmd n"
+				fi
+				p=$((ruleid/2))
+				cmd="$cmd y mask $((ruleid%2)) 0x1 y mask $((p%2)) 0x1 n n n n n n n n n n n n n n n y n n n n n n n y $qid n n 0 0 n n n n n n n n n n n n n n n n n n n n 0"
+				#echo $cmd
+				$cmd
+				ruleid=`expr $ruleid + 1`
+			done
+		done
+		ssdk_sh acl list bind $listid 0 1 $portmap
+	done
+}
+
+function create_war_cosmap(){
+	ssdk_sh cosmap pri2q set 0 0
+	ssdk_sh cosmap pri2q set 1 0
+	ssdk_sh cosmap pri2q set 2 0
+	ssdk_sh cosmap pri2q set 3 0
+	ssdk_sh cosmap pri2q set 4 1
+	ssdk_sh cosmap pri2q set 5 1
+	ssdk_sh cosmap pri2q set 6 1
+	ssdk_sh cosmap pri2q set 7 1
+	ssdk_sh cosmap pri2ehq set 0 0
+	ssdk_sh cosmap pri2ehq set 1 0
+	ssdk_sh cosmap pri2ehq set 2 0
+	ssdk_sh cosmap pri2ehq set 3 0
+	ssdk_sh cosmap pri2ehq set 4 1
+	ssdk_sh cosmap pri2ehq set 5 1
+	ssdk_sh cosmap pri2ehq set 6 1
+	ssdk_sh cosmap pri2ehq set 7 1
+}
+
+function create_acl_byp_egstp_rules(){
+	chip_ver=$1
+	cmd="ssdk_sh servcode config set 1 n 0 0xfffefc7f 0xffbdff 0 0 0 0 0 0"
+	if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		cmd="$cmd 0"
+	fi
+	#echo $cmd
+	$cmd
+
+	ssdk_sh acl list create 56 48
+	#action bypass eg stp check
+	action="y n n n n n n n n n n 0 0 n n n n n n n n n n n n n y n n n n n n n n n n n n y n n n n n n n n n n n n n n n n n n"
+	if [ "$chip_ver" == "0x2000" ]; then
+		action="$action n n 0"
+	elif [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		action="$action n n n 0"
+	else
+		action="$action 0"
+	fi
+
+	for ruleid in $( seq 0 2 )
+	do
+		if [ "$ruleid" == "0" ];then
+			cmd="ssdk_sh acl rule add 56 0 1 n 0 0 mac n n n n n y 01-80-c2-00-00-00 ff-ff-ff-ff-ff-ff n n n n n n n n n n n n n n n n n n n n n n n"
+		elif [ "$ruleid" == "1" ];then
+			cmd="ssdk_sh acl rule add 56 1 1 n 0 0 mac n n n n n n n yes 0x8809 0xffff n n n n n n n n n n n n n n n n n n n n n"
+		else
+			cmd="ssdk_sh acl rule add 56 2 1 n 0 0 mac n n n n n n n yes 0x888e 0xffff n n n n n n n n n n n n n n n n n n n n n"
+		fi
+		if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+			cmd="$cmd n $action"
+		else
+			cmd="$cmd $action"
+		fi
+		#echo $cmd
+		$cmd
+	done
+	ssdk_sh acl list bind 56 0 2 1
+}
+
+function delete_war_acl_rules(){
+	for lw in $side
+	do
+		#echo $lw
+		if [ "$lw" == "wan" ];then
+			listid=254
+			queue=$qwan
+			portmap=0x20
+		else
+			listid=255
+			queue=$qlan
+			portmap=0x1e
+		fi
+		ssdk_sh acl list unbind $listid 0 1 $portmap
+		for rt in $ruletype
+		do
+			for qid in $queue
+			do
+				cmd="ssdk_sh acl rule del $listid 0 1"
+				echo $cmd
+				$cmd
+			done
+		done
+		#echo "deleting list $listid"
+		ssdk_sh acl list destroy $listid
+	done
+}
+
+function delete_war_cosmap(){
+	ssdk_sh cosmap pri2q set 0 0
+	ssdk_sh cosmap pri2q set 1 0
+	ssdk_sh cosmap pri2q set 2 1
+	ssdk_sh cosmap pri2q set 3 1
+	ssdk_sh cosmap pri2q set 4 2
+	ssdk_sh cosmap pri2q set 5 2
+	ssdk_sh cosmap pri2q set 6 3
+	ssdk_sh cosmap pri2q set 7 3
+	ssdk_sh cosmap pri2ehq set 0 1
+	ssdk_sh cosmap pri2ehq set 1 0
+	ssdk_sh cosmap pri2ehq set 2 2
+	ssdk_sh cosmap pri2ehq set 3 2
+	ssdk_sh cosmap pri2ehq set 4 3
+	ssdk_sh cosmap pri2ehq set 5 3
+	ssdk_sh cosmap pri2ehq set 6 4
+	ssdk_sh cosmap pri2ehq set 7 5
+}
+
+function delete_acl_byp_egstp_rules(){
+	chip_ver=$1
+	cmd="ssdk_sh servcode config set 1 n 0 0xfffefcff 0xffbfff 0 0 0 0 0 0"
+	if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		cmd="$cmd 0"
+	fi
+	#echo $cmd
+	$cmd
+	ssdk_sh acl list unbind 56 0 2 1
+	ssdk_sh acl rule del 56 0 1
+	ssdk_sh acl rule del 56 1 1
+	ssdk_sh acl rule del 56 2 1
+	ssdk_sh acl list destroy 56
+}
+
+function edma_war_config_add(){
+	create_war_cosmap
+	ssdk_sh acl status set enable
+	create_war_acl_rules
+}
+
+function edma_war_config_del(){
+	delete_war_acl_rules
+	delete_war_cosmap
+}
+
+function ipq50xx_serdes_monitor () {
+	#if qca808x phy exist, need to monitor the serdes to avoid the effect for WIFI
+	port_id=2
+	old_linkstatus="DISABLE"
+	phy_id_info=`ssdk_sh port phyid get $port_id | grep Org | awk -F '!' '{print $2}'`
+	if [ "$phy_id_info" = "[Org ID]:0x004d[Rev ID]:0xd101" ]; then
+		ssdk_sh debug phy set 29 0xb 0x300d
+		ssdk_sh debug uniphy set 0 0x7ac 0x300d 4
+
+		while true
+		do
+			cur_linkstatus=`ssdk_sh port linkstatus get $port_id | grep Status | awk -F ':' '{print $2}'`
+			#when qca808x phy link status is from down to up, serdes tx would be enabled
+			if [ "$cur_linkstatus" = "ENABLE" ] && [ "$old_linkstatus" = "DISABLE" ]; then
+				ssdk_sh debug phy set 29 0xb 0xb00d
+				ssdk_sh debug uniphy set 0 0x7ac 0xb00d 4
+			fi
+			#when qca808x phy link status is from up to down, serdes tx would be disabled
+			if [ "$cur_linkstatus" = "DISABLE" ] && [ "$old_linkstatus" = "ENABLE" ]; then
+				ssdk_sh debug phy set 29 0xb 0x300d
+				ssdk_sh debug uniphy set 0 0x7ac 0x300d 4
+			fi
+			old_linkstatus=$cur_linkstatus
+		done
+	fi
+}
+
+function ipq53xx_phy_amplitude_set () {
+	#for qca808x phy sgmii, set half amplitude with src_half_swing register
+	port_id=2
+	phy_id_info=`ssdk_sh port phyid get $port_id | grep Org | awk -F '!' '{print $2}'`
+	if [ "$phy_id_info" = "[Org ID]:0x004d[Rev ID]:0xd180" ]; then
+		ssdk_sh debug phy set 5 0x40010087 0x208a
+		ssdk_sh debug phy set 6 0x40010087 0x208a
+		#Set the Reg0x67 bits[7:5]=3’b000 and bit4=1’b1
+		ampl_val=$(eval "ssdk_sh debug phy get 5 0x40010067 | grep SSDK | grep -oE '0x[0-9a-fA-F]+' | sed 's/\(0x..\)./\11/'")
+		ssdk_sh debug phy set 5 0x40010067 $ampl_val
+		ampl_val=$(eval "ssdk_sh debug phy get 6 0x40010067 | grep SSDK | grep -oE '0x[0-9a-fA-F]+' | sed 's/\(0x..\)./\11/'")
+		ssdk_sh debug phy set 6 0x40010067 $ampl_val
+	fi
+}
+
+function ipq53xx_uniphy_amplitude_set () {
+	#for ipq50xx sgmii, set half amplitude with tx_emp_lvl/margin_index and tx_margin
+	ssdk_sh debug uniphy set 0 0x7ac 0xb10d 4
+	ssdk_sh debug uniphy set 0 0x24 0 4
+	ssdk_sh debug uniphy set 1 0x7ac 0xb10d 4
+	ssdk_sh debug uniphy set 1 0x24 0 4
+}
+
+ssdk_dependency() {
+	counter=0
+	[ -e /lib/modules/$(uname -r)/qca-ssdk.ko ] && [ ! -d /sys/module/qca_ssdk ] && {
+		insmod qca-ssdk.ko
+	}
+	while [ ! -d /sys/ssdk ] && [ "$counter" -le 5 ]
+	do
+		sleep 1
+		counter=$((counter+1))
+	done
+}
+
+start() {
+	ssdk_dependency
+	chip_ver=`ssdk_sh debug reg get 0 4 | grep Data | tr -d 'SSDK Init OK![Data]:'`
+	#The following commands should be uncommented to enable EDMA WAR
+	if [ "$chip_ver" = "0x1401" ]; then
+		#edma_war_config_add
+		echo ''
+	fi
+	#The following commands should be uncommented to add acl egress stp bypass rules
+	if [ "$chip_ver" = "0x1500" ] || [ "$chip_ver" = "0x1501" ] || [ "$chip_ver" = "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		#create_acl_byp_egstp_rules $chip_ver
+		echo ''
+	fi
+	#The following commands should be uncommented to enable WAR for ipq50xx
+	chip_type_info=`cat tmp/sysinfo/model`
+	result=$(echo $chip_type_info | grep "IPQ5018")
+	if [ "$result" != "" ]; then
+		#ipq50xx_serdes_monitor &
+		#ipq50xx_uniphy_amplitude_set
+		#ipq50xx_phy_amplitude_set
+		echo ''
+	fi
+	if [ "$chip_ver" = "0x2001" ]; then
+		ipq53xx_uniphy_amplitude_set
+		ipq53xx_phy_amplitude_set
+		echo ''
+	fi
+	echo starting
+}
+
+stop() {
+	chip_ver=`ssdk_sh debug reg get 0 4 | grep Data | tr -d 'SSDK Init OK![Data]:'`
+	#The following commands should be uncommented to disable EDMA WAR
+	if [ "$chip_ver" = "0x1401" ]; then
+		#edma_war_config_del
+		echo ''
+	fi
+	#The following commands should be uncommented to delete acl egress stp bypass rules
+	if [ "$chip_ver" = "0x1500" ] || [ "$chip_ver" = "0x1501" ] || [ "$chip_ver" = "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		#delete_acl_byp_egstp_rules $chip_ver
+		echo ''
+	fi
+	echo stoping
+}

feeds/qca-wifi-7/qca-ssdk-qca/files-zyxel_nwa50be/qca-ssdk

@@ -0,0 +1,315 @@
+#!/bin/sh /etc/rc.common
+# Copyright (c) 2018, 2021, The Linux Foundation. All rights reserved.
+# Copyright (c) 2022-2024, Qualcomm Innovation Center, Inc. All rights reserved.
+#
+# Permission to use, copy, modify, and/or distribute this software for any
+# purpose with or without fee is hereby granted, provided that the above
+# copyright notice and this permission notice appear in all copies.
+#
+# THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+# WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+# MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+# ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+# WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+# ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+# OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+#
+
+START=16
+
+#!/bin/sh
+ruletype="ip4 ip6"
+side="wan lan"
+qwan="1 3 2 0 5 7 6 4"
+qlan="0 1 2 3 4 5 6 7"
+
+function create_war_acl_rules(){
+	for lw in $side
+	do
+		#echo $lw
+		if [ "$lw" == "wan" ];then
+			listid=254
+			queue=$qwan
+			portmap=0x20
+		else
+			listid=255
+			queue=$qlan
+			portmap=0x1e
+		fi
+		#echo $queue
+		#echo "creating list $listid"
+		ssdk_sh acl list create $listid 255
+		ruleid=0
+		for rt in $ruletype
+		do
+			for qid in $queue
+			do
+				cmd="ssdk_sh acl rule add $listid $ruleid  1 n 0 0"
+				#echo $cmd
+				if [ "$rt" == "ip4" ];then
+					cmd="$cmd ip4 n n n n n n n n n n n n n n n n n n n n n n n n n n n n n"
+					#echo $cmd
+				else
+					cmd="$cmd ip6 n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n"
+					#echo $cmd
+				fi
+				if [ $ruleid -le 3 ];then
+					#non-zero dscp
+					cmd="$cmd y 0x0 0xff"
+				elif [ $ruleid -le 7 ];then
+					#zero dscp
+					cmd="$cmd n"
+				elif [ $ruleid -le 11 ];then
+					#non-zero dscp
+					cmd="$cmd y 0x0 0xff"
+				else
+					#zero dscp
+					cmd="$cmd n"
+				fi
+				p=$((ruleid/2))
+				cmd="$cmd y mask $((ruleid%2)) 0x1 y mask $((p%2)) 0x1 n n n n n n n n n n n n n n n y n n n n n n n y $qid n n 0 0 n n n n n n n n n n n n n n n n n n n n 0"
+				#echo $cmd
+				$cmd
+				ruleid=`expr $ruleid + 1`
+			done
+		done
+		ssdk_sh acl list bind $listid 0 1 $portmap
+	done
+}
+
+function create_war_cosmap(){
+	ssdk_sh cosmap pri2q set 0 0
+	ssdk_sh cosmap pri2q set 1 0
+	ssdk_sh cosmap pri2q set 2 0
+	ssdk_sh cosmap pri2q set 3 0
+	ssdk_sh cosmap pri2q set 4 1
+	ssdk_sh cosmap pri2q set 5 1
+	ssdk_sh cosmap pri2q set 6 1
+	ssdk_sh cosmap pri2q set 7 1
+	ssdk_sh cosmap pri2ehq set 0 0
+	ssdk_sh cosmap pri2ehq set 1 0
+	ssdk_sh cosmap pri2ehq set 2 0
+	ssdk_sh cosmap pri2ehq set 3 0
+	ssdk_sh cosmap pri2ehq set 4 1
+	ssdk_sh cosmap pri2ehq set 5 1
+	ssdk_sh cosmap pri2ehq set 6 1
+	ssdk_sh cosmap pri2ehq set 7 1
+}
+
+function create_acl_byp_egstp_rules(){
+	chip_ver=$1
+	cmd="ssdk_sh servcode config set 1 n 0 0xfffefc7f 0xffbdff 0 0 0 0 0 0"
+	if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		cmd="$cmd 0"
+	fi
+	#echo $cmd
+	$cmd
+
+	ssdk_sh acl list create 56 48
+	#action bypass eg stp check
+	action="y n n n n n n n n n n 0 0 n n n n n n n n n n n n n y n n n n n n n n n n n n y n n n n n n n n n n n n n n n n n n"
+	if [ "$chip_ver" == "0x2000" ]; then
+		action="$action n n 0"
+	elif [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		action="$action n n n 0"
+	else
+		action="$action 0"
+	fi
+
+	for ruleid in $( seq 0 2 )
+	do
+		if [ "$ruleid" == "0" ];then
+			cmd="ssdk_sh acl rule add 56 0 1 n 0 0 mac n n n n n y 01-80-c2-00-00-00 ff-ff-ff-ff-ff-ff n n n n n n n n n n n n n n n n n n n n n n n"
+		elif [ "$ruleid" == "1" ];then
+			cmd="ssdk_sh acl rule add 56 1 1 n 0 0 mac n n n n n n n yes 0x8809 0xffff n n n n n n n n n n n n n n n n n n n n n"
+		else
+			cmd="ssdk_sh acl rule add 56 2 1 n 0 0 mac n n n n n n n yes 0x888e 0xffff n n n n n n n n n n n n n n n n n n n n n"
+		fi
+		if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+			cmd="$cmd n $action"
+		else
+			cmd="$cmd $action"
+		fi
+		#echo $cmd
+		$cmd
+	done
+	ssdk_sh acl list bind 56 0 2 1
+}
+
+function delete_war_acl_rules(){
+	for lw in $side
+	do
+		#echo $lw
+		if [ "$lw" == "wan" ];then
+			listid=254
+			queue=$qwan
+			portmap=0x20
+		else
+			listid=255
+			queue=$qlan
+			portmap=0x1e
+		fi
+		ssdk_sh acl list unbind $listid 0 1 $portmap
+		for rt in $ruletype
+		do
+			for qid in $queue
+			do
+				cmd="ssdk_sh acl rule del $listid 0 1"
+				echo $cmd
+				$cmd
+			done
+		done
+		#echo "deleting list $listid"
+		ssdk_sh acl list destroy $listid
+	done
+}
+
+function delete_war_cosmap(){
+	ssdk_sh cosmap pri2q set 0 0
+	ssdk_sh cosmap pri2q set 1 0
+	ssdk_sh cosmap pri2q set 2 1
+	ssdk_sh cosmap pri2q set 3 1
+	ssdk_sh cosmap pri2q set 4 2
+	ssdk_sh cosmap pri2q set 5 2
+	ssdk_sh cosmap pri2q set 6 3
+	ssdk_sh cosmap pri2q set 7 3
+	ssdk_sh cosmap pri2ehq set 0 1
+	ssdk_sh cosmap pri2ehq set 1 0
+	ssdk_sh cosmap pri2ehq set 2 2
+	ssdk_sh cosmap pri2ehq set 3 2
+	ssdk_sh cosmap pri2ehq set 4 3
+	ssdk_sh cosmap pri2ehq set 5 3
+	ssdk_sh cosmap pri2ehq set 6 4
+	ssdk_sh cosmap pri2ehq set 7 5
+}
+
+function delete_acl_byp_egstp_rules(){
+	chip_ver=$1
+	cmd="ssdk_sh servcode config set 1 n 0 0xfffefcff 0xffbfff 0 0 0 0 0 0"
+	if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		cmd="$cmd 0"
+	fi
+	#echo $cmd
+	$cmd
+	ssdk_sh acl list unbind 56 0 2 1
+	ssdk_sh acl rule del 56 0 1
+	ssdk_sh acl rule del 56 1 1
+	ssdk_sh acl rule del 56 2 1
+	ssdk_sh acl list destroy 56
+}
+
+function edma_war_config_add(){
+	create_war_cosmap
+	ssdk_sh acl status set enable
+	create_war_acl_rules
+}
+
+function edma_war_config_del(){
+	delete_war_acl_rules
+	delete_war_cosmap
+}
+
+function ipq50xx_serdes_monitor () {
+	#if qca808x phy exist, need to monitor the serdes to avoid the effect for WIFI
+	port_id=2
+	old_linkstatus="DISABLE"
+	phy_id_info=`ssdk_sh port phyid get $port_id | grep Org | awk -F '!' '{print $2}'`
+	if [ "$phy_id_info" = "[Org ID]:0x004d[Rev ID]:0xd101" ]; then
+		ssdk_sh debug phy set 29 0xb 0x300d
+		ssdk_sh debug uniphy set 0 0x7ac 0x300d 4
+
+		while true
+		do
+			cur_linkstatus=`ssdk_sh port linkstatus get $port_id | grep Status | awk -F ':' '{print $2}'`
+			#when qca808x phy link status is from down to up, serdes tx would be enabled
+			if [ "$cur_linkstatus" = "ENABLE" ] && [ "$old_linkstatus" = "DISABLE" ]; then
+				ssdk_sh debug phy set 29 0xb 0xb00d
+				ssdk_sh debug uniphy set 0 0x7ac 0xb00d 4
+			fi
+			#when qca808x phy link status is from up to down, serdes tx would be disabled
+			if [ "$cur_linkstatus" = "DISABLE" ] && [ "$old_linkstatus" = "ENABLE" ]; then
+				ssdk_sh debug phy set 29 0xb 0x300d
+				ssdk_sh debug uniphy set 0 0x7ac 0x300d 4
+			fi
+			old_linkstatus=$cur_linkstatus
+		done
+	fi
+}
+
+function ipq53xx_phy_amplitude_set () {
+	#PHY (8081->5321): Full amplitude (bit[7:5]=000), half swing (bit[4]=1)
+	#for qca808x phy sgmii, set half amplitude with src_half_swing register
+	port_id=2
+	phy_addr=0x1d
+	phy_id_info=`ssdk_sh port phyid get $port_id | grep Org | awk -F '!' '{print $2}'`
+	if [ "$phy_id_info" = "[Org ID]:0x004d[Rev ID]:0xd101" ]; then
+		ssdk_sh debug phy set $phy_addr 0x40010087 0x208a
+		#Set the Reg0x67 bits[7:5]=3’b000 and bit4=1’b1
+		ampl_val=$(ssdk_sh debug phy get $phy_addr 0x40010067 | grep SSDK | grep -oE '0x[0-9a-fA-F]+' | sed 's/\(0x..\)./\11/')
+		ssdk_sh debug phy set $phy_addr 0x40010067 $ampl_val
+	fi
+}
+
+function ipq53xx_uniphy_amplitude_set () {
+        #UniPhy (5321->8081): Custom amplitude (bit[8:4]=21) = 0xb15d
+	#for ipq53xx sgmii, set half amplitude with tx_emp_lvl/margin_index and tx_margin
+	ssdk_sh debug uniphy set 1 0x7ac 0xb15d 4
+	ssdk_sh debug uniphy set 1 0x24 0 4
+}
+
+ssdk_dependency() {
+	counter=0
+	[ -e /lib/modules/$(uname -r)/qca-ssdk.ko ] && [ ! -d /sys/module/qca_ssdk ] && {
+		insmod qca-ssdk.ko
+	}
+	while [ ! -d /sys/ssdk ] && [ "$counter" -le 5 ]
+	do
+		sleep 1
+		counter=$((counter+1))
+	done
+}
+
+start() {
+	ssdk_dependency
+	chip_ver=`ssdk_sh debug reg get 0 4 | grep Data | tr -d 'SSDK Init OK![Data]:'`
+	#The following commands should be uncommented to enable EDMA WAR
+	if [ "$chip_ver" = "0x1401" ]; then
+		#edma_war_config_add
+		echo ''
+	fi
+	#The following commands should be uncommented to add acl egress stp bypass rules
+	if [ "$chip_ver" = "0x1500" ] || [ "$chip_ver" = "0x1501" ] || [ "$chip_ver" = "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		#create_acl_byp_egstp_rules $chip_ver
+		echo ''
+	fi
+	#The following commands should be uncommented to enable WAR for ipq50xx
+	chip_type_info=`cat tmp/sysinfo/model`
+	result=$(echo $chip_type_info | grep "IPQ5018")
+	if [ "$result" != "" ]; then
+		#ipq50xx_serdes_monitor &
+		#ipq50xx_uniphy_amplitude_set
+		#ipq50xx_phy_amplitude_set
+		echo ''
+	fi
+	if [ "$chip_ver" = "0x2001" ]; then
+		ipq53xx_uniphy_amplitude_set
+		ipq53xx_phy_amplitude_set
+		echo ''
+	fi
+	echo starting
+}
+
+stop() {
+	chip_ver=`ssdk_sh debug reg get 0 4 | grep Data | tr -d 'SSDK Init OK![Data]:'`
+	#The following commands should be uncommented to disable EDMA WAR
+	if [ "$chip_ver" = "0x1401" ]; then
+		#edma_war_config_del
+		echo ''
+	fi
+	#The following commands should be uncommented to delete acl egress stp bypass rules
+	if [ "$chip_ver" = "0x1500" ] || [ "$chip_ver" = "0x1501" ] || [ "$chip_ver" = "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		#delete_acl_byp_egstp_rules $chip_ver
+		echo ''
+	fi
+	echo stoping
+}

feeds/tip/certificates/files/etc/init.d/early_boot

@@ -20,10 +20,16 @@ copy_certificates() {
 	[ -z "$country" ] && country=US
 	echo "options cfg80211 ieee80211_regdom="$country > /etc/modules.conf 
 	echo -n $country > /etc/ucentral/country
+	sync
 	exit 0
 }
 
 boot() {
+	case "$(board_name)" in
+	sonicfi,rap6*)
+		touch /tmp/squashfs
+	;;
+	esac
 	[ -f /etc/ucentral/key.pem ] && return
 	/usr/bin/mount_certs
 	copy_certificates

feeds/tip/certificates/files/usr/bin/mount_certs

@@ -6,13 +6,16 @@ check_certificates() {
 
 check_certificates
 
-bootconfig_lookup() {
-	case "$(fw_printenv -n cert_part)" in
-	0)	echo "0:BOOTCONFIG"
-		;;
-	1)	echo "0:BOOTCONFIG1"
-		;;
-	esac
+tar_part_lookup() {
+	part="$(fw_printenv -n cert_part)"
+	if [ "$part" -eq 0 ]; then
+		echo "$2"
+		part=1
+	else
+		echo "$1"
+		part=0
+	fi
+	fw_setenv cert_part $part
 }
 
 . /lib/functions.sh
@@ -34,12 +37,29 @@ sonicfi,rap7*)
 		mtd=$(find_mtd_index certificates)
 		[ -n "$mtd" ] && mount -t ext4 /dev/mtdblock$mtd /certificates
 	fi
-	if [ ! -f /certificates/cert.pem ] || [ ! -f /certificates/key.pem ]; then
-		bootconfig=$(bootconfig_lookup)
-		if [ -n "$bootconfig" ]; then
-			mmc_dev=$(echo $(find_mmc_part "$bootconfig") | sed 's/^.\{5\}//')
-			[ -n "$mmc_dev" ] && tar xf /dev/$mmc_dev -C /certificates
-		fi
+	;;
+sonicfi,rap6*)
+	mtd=$(find_mtd_index certificates)
+	if [ "$(head -c 4 /dev/mtd$mtd)" == "hsqs" ]; then
+		mount -t squashfs /dev/mtdblock$mtd /mnt
+		cp /mnt/* /certificates
+		umount /mnt
+	fi
+		mtd=$(find_mtd_index devinfo)
+		[ -n "$mtd" ] && tar xf /dev/mtdblock$mtd -C /certificates
+	;;
+udaya,a5-id2|\
+yuncore,ax820)
+	mtd=$(find_mtd_index certificates)
+	if [ "$(head -c 4 /dev/mtd$mtd)" == "hsqs" ]; then
+		mount -t squashfs /dev/mtdblock$mtd /mnt
+		cp /mnt/* /certificates
+		umount /mnt
+	fi
+	part=$(tar_part_lookup "insta1" "insta2")
+	if [ -n "insta" ]; then
+		mtd=$(find_mtd_index $part)
+		[ -n "$mtd" ] && tar xf /dev/mtdblock$mtd -C /certificates
 	fi
 	;;
 *)

feeds/tip/certificates/files/usr/bin/store_certs

@@ -1,25 +1,36 @@
 #!/bin/sh
 
-bootconfig_lookup() {
-	bootconfig="$(fw_printenv -n cert_part)"
-	case "$(fw_printenv -n cert_part)" in
-	0)	echo "0:BOOTCONFIG1"
-		bootconfig=1
-		;;
-	*)	echo "0:BOOTCONFIG"
-		bootconfig=0
-		;;
-	esac
-	fw_setenv cert_part $bootconfig
+tar_part_lookup() {
+	part="$(fw_printenv -n cert_part)"
+	if [ "$part" -eq 0 ]; then
+		echo "$2"
+		part=1
+	else
+		echo "$1"
+		part=0
+	fi
+	fw_setenv cert_part $part
 }
 
 . /lib/functions.sh
 case "$(board_name)" in
-sonicfi,rap7110c-341x)
+udaya,a5-id2|\
+yuncore,ax820)
 	cd /certificates
-	tar cf /tmp/certs.tar
-	bootconfig=$(bootconfig_lookup)
-	mmc_dev=$(echo $(find_mmc_part $bootconfig) | sed 's/^.\{5\}//')
-	dd if=/tmp/certs.tar of=/dev/$bootconfig
+	tar cf /tmp/certs.tar .
+	part=$(tar_part_lookup "insta1" "insta2")
+	mtd=$(find_mtd_index $part)
+	dd if=/tmp/certs.tar of=/dev/mtdblock$mtd
+	;;
+sonicfi,rap6*)
+	if [ "$(fw_printenv -n store_certs_disabled)" != "1" ]; then
+		cd /certificates
+		tar cf /tmp/certs.tar .
+		mtd=$(find_mtd_index devinfo)
+		block_size=$(cat /sys/class/mtd/mtd$mtd/size)
+		dd if=/tmp/certs.tar of=/tmp/certs_pad.tar bs=$block_size conv=sync
+		mtd write /tmp/certs_pad.tar /dev/mtd$mtd
+		rm -f /tmp/certs.tar /tmp/certs_pad.tar
+	fi
 	;;
 esac

feeds/tip/cloud_discovery/files/etc/init.d/cloud_discover

@@ -22,6 +22,19 @@ start_service() {
 	[ "$valid" == "true" ] || 
 		/usr/share/ucentral/ucentral.uc /etc/ucentral/ucentral.cfg.0000000001 > /dev/null
 
+	est_client check
+	[ $? -eq 1 ] && {
+		logger ERROR
+		logger ERROR
+		logger ERROR
+		logger The certificate used has a CN that does not match the serial of the device
+		echo The certificate used has a CN that does not match the serial of the device
+		logger ERROR
+		logger ERROR
+		logger ERROR
+		return
+	}
+
 	procd_open_instance
 	procd_set_param command "$PROG"
 	procd_set_param respawn

feeds/tip/cloud_discovery/files/usr/bin/cloud_discovery

@@ -15,9 +15,15 @@ const ONLINE = 2;
 const OFFLINE = 3;
 const ORPHAN = 4;
 
+const DISCOVER_DHCP = "DHCP";
+const DISCOVER_FLASH = "FLASH";
+const DISCOVER_LOOKUP = "OpenLAN";
+
 let ubus = libubus.connect();
 let uci = libuci.cursor();
 let state = DISCOVER;
+let discovery_method = "";
+let discovery_block_list = [];
 let validate_time;
 let offline_time;
 let orphan_time;
@@ -27,6 +33,8 @@ let timeouts = {
 	'validate': 120,
 	'orphan': 2 * 60 * 60,
 	interval: 10000,
+	expiry_interval: 60 * 60 * 1000,
+	expiry_threshold: 1 * 365 * 24 * 60 * 60,
 };
 
 ulog_open(ULOG_SYSLOG | ULOG_STDIO, LOG_DAEMON, "cloud_discover");
@@ -35,6 +43,24 @@ ulog(LOG_INFO, 'Start\n');
 
 uloop.init();
 
+let cds_server = 'discovery.open-lan.org';
+
+function detect_certificate_type() {
+	let pipe = fs.popen(`openssl x509 -in /etc/ucentral/cert.pem -noout -issuer`);
+	let issuer = pipe.read("all");
+	pipe.close();
+
+	if (match(issuer, /OpenLAN Demo Birth CA/)) {
+		ulog(LOG_INFO, 'Certificate type is "Demo" \n');
+		cds_server = 'discovery-qa.open-lan.org';
+		timeouts.expiry_threshold = 3 * 24 * 60 * 60;
+	} else if (match(issuer, /OpenLAN Birth Issuing CA/)) {
+		ulog(LOG_INFO, 'Certificate type is "Production"\n');
+	} else {
+		ulog(LOG_INFO, 'Certificate type is "TIP"\n');
+	}
+}
+
 function readjsonfile(path) {
 	let file = fs.readfile(path);
 	if (file)
@@ -76,6 +102,17 @@ function gateway_load() {
 	return readjsonfile('/etc/ucentral/gateway.json');
 }
 
+function discovery_state_write() {
+	if (length(discovery_method) == 0)
+		return;
+
+	let discovery_state = {
+		"type": discovery_method,
+		"updated": time()
+	};
+	fs.writefile('/etc/ucentral/discovery.state.json', discovery_state);
+}
+
 function gateway_write(data) {
 	let gateway = gateway_load();
 	gateway ??= {};
@@ -89,8 +126,10 @@ function gateway_write(data) {
 		if (new[key] != gateway[key])
 			changed = true;
 	}
-	if (changed)
+	if (changed) {
 		fs.writefile('/etc/ucentral/gateway.json', new);
+		system('sync');
+	}
 	return changed;
 }
 
@@ -120,6 +159,7 @@ function set_state(set) {
 		ulog(LOG_INFO, 'Wait for validation\n');
 		validate_time = time();
 		state = VALIDATING;
+		push(discovery_block_list, discovery_method);
 		break;
 
 	case ONLINE:
@@ -127,6 +167,8 @@ function set_state(set) {
 		if (prev == VALIDATING) {
 			ulog(LOG_INFO, 'Setting cloud controller to validated\n');
 			gateway_write({ valid: true });
+			discovery_state_write();
+			discovery_block_list = [];
 		}
 		break;
 
@@ -161,7 +203,7 @@ function redirector_lookup() {
 	let serial = uci.get('system', '@system[-1]', 'mac');
 
 	fs.unlink(path);
-	system(`curl -k --cert /etc/ucentral/operational.pem --key /etc/ucentral/key.pem --cacert /etc/ucentral/operational.ca https://openlan.keys.tip.build/v1/devices/${serial} --output /tmp/ucentral.redirector`);
+	system(`curl -k --cert /etc/ucentral/operational.pem --key /etc/ucentral/key.pem --cacert /etc/ucentral/operational.ca https://${cds_server}/v1/devices/${serial} --output /tmp/ucentral.redirector`);
 	if (!fs.stat(path))
 		return;
 	let redir = readjsonfile(path);
@@ -195,6 +237,13 @@ function time_is_valid() {
 	return valid;
 }
 
+function is_discover_method_blacked() {
+	if (discovery_method in discovery_block_list)
+		return true;
+
+	return false;
+}
+
 function interval_handler() {
 	printf(`State ${state}\n`);
 	switch(state) {
@@ -224,16 +273,21 @@ function interval_handler() {
 		if (!time_is_valid())
 			return;
 
-		if (discover_dhcp())
-			return;
-
 		if (system('/usr/bin/est_client enroll'))
 			return;
 
-		if (!discover_flash())
+		discovery_method = DISCOVER_DHCP;
+		if (!is_discover_method_blacked() && discover_dhcp())
 			return;
 
+		discovery_method = DISCOVER_FLASH;
+		if (!is_discover_method_blacked() && !discover_flash())
+			return;
+
+		discovery_method = DISCOVER_LOOKUP;
 		redirector_lookup();
+
+		discovery_block_list = [];
 		break;
 
 	case VALIDATING:
@@ -252,6 +306,36 @@ function interval_handler() {
 	}
 }
 
+function trigger_reenroll() {
+	ulog(LOG_INFO, 'triggering reenroll\n');
+
+	if (system('/usr/bin/est_client reenroll')) {
+		ulog(LOG_INFO, 'reenroll failed\n');
+		return;
+	}
+	
+	ulog(LOG_INFO, 'reenroll succeeded\n');
+	ulog(LOG_INFO, 'stopping client\n');
+	
+	system('/etc/init.d/ucentral stop');
+	set_state(DISCOVER);
+}
+
+function expiry_handler() {
+	let stat = fs.stat('/etc/ucentral/operational.ca');
+	if (!stat)
+		return;
+
+	let ret = system(`openssl x509 -checkend ${timeouts.expiry_threshold} -noout -in /certificates/operational.pem`);
+	if (!ret) {
+		ulog(LOG_INFO, 'checked certificate expiry - all ok\n');
+		return;
+	}
+
+	ulog(LOG_INFO, 'certificate will expire soon\n');
+	trigger_reenroll();
+}
+
 let ubus_methods = {
 	discover: {
 		call: function(req) {
@@ -326,8 +410,17 @@ let ubus_methods = {
 		},
 		args: {},
 	},
+	reenroll: {
+		call: function(req) {
+			trigger_reenroll();
+			return 0;
+		},
+		args: {},
+	},
 };
 
+detect_certificate_type();
+
 if (gateway_available()) {
 	let status = ubus.call('ucentral', 'status');
 	ulog(LOG_INFO, 'cloud is known\n');
@@ -344,6 +437,7 @@ if (gateway_available()) {
 timeouts_load();
 
 interval = uloop.interval(timeouts.interval, interval_handler);
+uloop.interval(timeouts.expiry_interval, expiry_handler);
 
 ubus.publish('cloud', ubus_methods);
 

feeds/tip/cloud_discovery/files/usr/bin/est_client

@@ -4,12 +4,28 @@
 
 import { ulog_open, ulog, ULOG_SYSLOG, ULOG_STDIO, LOG_DAEMON, LOG_INFO } from 'log';
 import * as fs from 'fs';
+import * as libuci from 'uci';
 
 let store_operational_pem = false;
 let store_operational_ca = false;
-let est_server = 'qaest.certificates.open-lan.org:8001';
+let est_server = 'est.certificates.open-lan.org';
 let cert_prefix = 'operational';
 
+function set_est_server() {
+	let pipe = fs.popen(`openssl x509 -in /etc/ucentral/cert.pem -noout -issuer`);
+	let issuer = pipe.read("all");
+	pipe.close();
+
+	if (match(issuer, /OpenLAN Demo Birth CA/)) {
+		ulog(LOG_INFO, 'Certificate type is "Demo" \n');
+		est_server = 'qaest.certificates.open-lan.org:8001';
+	} else if (match(issuer, /OpenLAN Birth Issuing CA/)) {
+		ulog(LOG_INFO, 'Certificate type is "Production"\n');
+	} else {
+		ulog(LOG_INFO, 'Certificate type is "TIP"\n');
+	}
+}
+
 if (getenv('EST_SERVER'))
 	est_server = getenv('EST_SERVER');
 
@@ -78,6 +94,8 @@ function call_est_server(path, cert, target) {
 	if (generate_csr(cert))
 		return 1;
 
+	set_est_server();	
+
 	let ret = system('curl -m 10 -X POST https://' + est_server + '/.well-known/est/' + path + ' -d @/tmp/csr.nohdr.p10 -H "Content-Type: application/pkcs10" --cert ' + cert + ' --key /etc/ucentral/key.pem --cacert /etc/ucentral/insta.pem -o /tmp/operational.nohdr.p7');
 	if (ret) {
 		ulog(LOG_INFO, 'Failed to request operational certificate\n');
@@ -125,6 +143,9 @@ function load_operational_ca() {
 		ulog(LOG_INFO, 'Operational CA is present\n');
 		return 0;
 	}
+
+	set_est_server();	
+
 	let ret = system('curl -m 10 -X GET https://' + est_server + '/.well-known/est/cacerts --cert /etc/ucentral/' + cert_prefix + '.pem --key /etc/ucentral/key.pem --cacert /etc/ucentral/insta.pem -o /tmp/' + cert_prefix + '.ca.nohdr.p7');
 	if (!ret)
 		ret = p7_too_pem('/tmp/' + cert_prefix + '.ca.nohdr.p7', '/etc/ucentral/' + cert_prefix + '.ca');
@@ -139,11 +160,14 @@ function load_operational_ca() {
 }
 
 function fwtool() {
+	if (!fs.stat('/etc/ucentral/cert.pem'))
+		return 0;
+
 	let pipe = fs.popen(`openssl x509 -in /etc/ucentral/cert.pem -noout -issuer`);
 	let issuer = pipe.read("all");
 	pipe.close();
 
-	if (!(match(issuer, /OpenLAN/) && match(issuer, /Birth CA/)))
+	if (!(match(issuer, /OpenLAN/) && match(issuer, /Birth/)))
 		return 0;
 
 	ulog(LOG_INFO, 'The issuer is insta\n');
@@ -163,6 +187,20 @@ function fwtool() {
 	return 0;
 }
 
+function check_cert() {
+	if (!fs.stat('/etc/ucentral/cert.pem'))
+		return 0;
+	let pipe = fs.popen("openssl x509 -in /etc/ucentral/cert.pem  -noout -subject -nameopt multiline | grep commonName | awk '{ print $3 }'");
+	let cn = pipe.read("all");
+	pipe.close();
+	if (!cn)
+		return 0;
+	cn = lc(trim(cn));
+	let uci = libuci.cursor();
+	let serial = uci.get('ucentral', 'config', 'serial');
+	return cn != serial;
+}
+
 switch(ARGV[0]) {
 case 'enroll':
 	let ret = simpleenroll();
@@ -184,4 +222,7 @@ case 'reenroll':
 
 case 'fwtool':
 	exit(fwtool());
+
+case 'check':
+	exit(check_cert());
 }

feeds/tip/cloud_discovery/files/usr/share/ucentral/cloud_discovery.uc

@@ -5,8 +5,8 @@ import * as fs from 'fs';
 
 let cmd = ARGV[0];
 let ifname = getenv("interface");
-let opt224 = getenv("opt138");
-let opt224 = getenv("opt224");
+let opt138 = fs.readfile('/tmp/dhcp-option-138');
+let opt224 = fs.readfile('/tmp/dhcp-option-224');
 
 if (cmd != 'bound' && cmd != 'renew')
 	exit(0);
@@ -23,14 +23,14 @@ let cloud = {
 	lease: true,
 };
 if (opt138) {
-	let dhcp = hexdec(opt138);
+	let dhcp = opt138;
 	dhcp = split(dhcp, ':');
 	cloud.dhcp_server = dhcp[0];
 	cloud.dhcp_port = dhcp[1] ?? 15002;
 	cloud.no_validation = true;
 }
 if (opt224) {
-	let dhcp = hexdec(opt224);
+	let dhcp = opt224;
 	dhcp = split(dhcp, ':');
 	cloud.dhcp_server = dhcp[0];
 	cloud.dhcp_port = dhcp[1] ?? 15002;

feeds/tip/tip-defaults/files/etc/ucentral/insta.pem

@@ -4,3 +4,6 @@ MIIFajCCA1KgAwIBAgICDnowDQYJKoZIhvcNAQELBQAwHzEdMBsGA1UEAwwUT3BlbkxBTiBEZW1vIFJv
 -----BEGIN CERTIFICATE-----
 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
 -----END CERTIFICATE-----
+-----BEGIN CERTIFICATE-----
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
+-----END CERTIFICATE-----

feeds/ucentral/ratelimit/files/usr/bin/ratelimit

@@ -350,7 +350,7 @@ function run_service() {
 				printf('-> reload\n');
 				let list = uctx.list();
 				for (let obj in list) {
-					if (!wildcard(obj, 'hostapd.wlan*'))
+					if (!wildcard(obj, 'hostapd.wlan*') && !wildcard(obj, 'hostapd.phy*'))
 						continue;
 					let iface = split(obj, '.')[1];
 					let device = get_device(devices, req.args.device);

feeds/ucentral/rrmd/files/etc/init.d/rrmd

@@ -6,6 +6,8 @@ STOP=01
 USE_PROCD=1
 
 start_service() {
+	[ -e "/tmp/rrm_timestamp" ] && rm -rf /tmp/rrm_timestamp
+	[ -e "/tmp/rrm_chan_switch" ] && rm -rf /tmp/rrm_chan_switch
 	rm -rf /tmp/threshold_breach_count*
 	rm -rf /tmp/fixed_channel*
 	rm -rf /tmp/chanutil_phy*

feeds/ucentral/rrmd/files/usr/share/rrmd/policy_chanutil.uc

@@ -24,6 +24,10 @@ function stats_info_write(path, value) {
 	file.close();
 }
 
+function record_rrm_timestamp() {
+    stats_info_write("/tmp/rrm_timestamp", time());
+}
+
 // total number of radios: default=2
 let num_radios = 2;
 let phy_count;
@@ -136,20 +140,122 @@ function channel_to_freq(band, channel) {
     return freq;
 }
 
-function center_freq_calc(band, freq, bandwidth) {
-    if (bandwidth == 40)
-        return +freq + 10;
-    if (bandwidth == 80)
-        return +freq + 30;
-    if (bandwidth == 160)
-        return +freq + 70;
-    if (bandwidth == 320)
-        if (freq == 6115)
-            return +freq - 10;
-        else
-            return +freq + 150;
+// using mapping to get correct center channel, especially for 6G radio
+function get_center_channel(channel, band, bw) {
+    let center_channel = channel;
+    let center_channel_map = {};
 
-    return +freq;
+    switch (band) {
+    case '5g':
+        if (bw == 40) {
+            center_channel_map = {
+                "36": 38, "40": 38,
+                "44": 46, "48": 46,
+                "52": 54, "56": 54,
+                "60": 62, "64": 62,
+                "100": 102, "104": 102,
+                "108": 110, "112": 110,
+                "116": 118, "120": 118,
+                "124": 126, "128": 126,
+                "132": 134, "136": 134,
+                "140": 142, "144": 142,
+                "149": 151, "153": 151,
+                "157": 159, "161": 159,
+                "165": 167
+            };
+        } else if (bw == 80) {
+            center_channel_map = {
+                "36": 42, "40": 42, "44": 42, "48": 42,
+                "52": 58, "56": 58, "60": 58, "64": 58,
+                "100": 106, "104": 106, "108": 106, "112": 106,
+                "116": 122, "120": 122, "124": 122, "128": 122,
+                "132": 138, "136": 138, "140": 138, "144": 138,
+                "149": 155, "153": 155, "157": 155, "161": 155,
+                "165": 171
+            };
+        } else if (bw == 160) {
+            center_channel_map = {
+                "36": 50, "40": 50, "44": 50, "48": 50,
+                "52": 50, "56": 50, "60": 50, "64": 50,
+                "100": 114, "104": 114, "108": 114, "112": 114,
+                "116": 114, "120": 114, "124": 114, "128": 114
+            };
+        }
+        break;
+    case '6g':
+        if (bw == 40) {
+            center_channel_map = {
+                "1": 3, "5": 3, "9": 11, "13": 11,
+                "17": 19, "21": 19, "25": 27, "29": 27,
+                "33": 35, "37": 35, "41": 43, "45": 43,
+                "49": 51, "53": 51, "57": 59, "61": 59,
+                "65": 67, "69": 67, "73": 75, "77": 75,
+                "81": 83, "85": 83, "89": 91, "93": 91,
+                "97": 99, "101": 99, "105": 107, "109": 107,
+                "113": 115, "117": 115, "121": 123, "125": 123,
+                "129": 131, "133": 131, "137": 139, "141": 139,
+                "145": 147, "149": 147, "153": 155, "157": 155,
+                "161": 163, "165": 163, "169": 171, "173": 171,
+                "177": 179, "181": 179, "185": 187, "189": 187,
+                "193": 195, "197": 195, "201": 203, "205": 203,
+                "209": 211, "213": 211, "217": 219, "221": 219,
+                "225": 227
+            };
+        } else if (bw == 80) {
+            center_channel_map = {
+                "1": 7, "5": 7, "9": 7, "13": 7,
+                "17": 23, "21": 23, "25": 23, "29": 23,
+                "33": 39, "37": 39, "41": 39, "45": 39,
+                "49": 55, "53": 55, "57": 55, "61": 55,
+                "65": 71, "69": 71, "73": 71, "77": 71,
+                "81": 87, "85": 87, "89": 87, "93": 87,
+                "97": 103, "101": 103, "105": 103, "109": 103,
+                "113": 119, "117": 119, "121": 119, "125": 119,
+                "129": 135, "133": 135, "137": 135, "141": 135,
+                "145": 151, "149": 151, "153": 151, "157": 151,
+                "161": 167, "165": 167, "169": 167, "173": 167,
+                "177": 183, "181": 183, "185": 183, "189": 183,
+                "193": 199, "197": 199, "201": 199, "205": 199,
+                "209": 215
+            };
+        } else if (bw == 160) {
+            center_channel_map = {
+                "1": 15, "5": 15, "9": 15, "13": 15,
+                "17": 15, "21": 15, "25": 15, "29": 15,
+                "33": 47, "37": 47, "41": 47, "45": 47,
+                "49": 47, "53": 47, "57": 47, "61": 47,
+                "65": 79, "69": 79, "73": 79, "77": 79,
+                "81": 79, "85": 79, "89": 79, "93": 79,
+                "97": 111, "101": 111, "105": 111, "109": 111,
+                "113": 111, "117": 111, "121": 111, "125": 111,
+                "129": 143, "133": 143, "137": 143, "141": 143,
+                "145": 143, "149": 143, "153": 143, "157": 143,
+                "161": 175, "165": 175, "169": 175, "173": 175,
+                "177": 175, "181": 175, "185": 175, "189": 175,
+                "193": 207
+            };
+        } else if (bw == 320) {
+            center_channel_map = {
+                "1": 31, "5": 31, "9": 31, "13": 31,
+                "17": 31, "21": 31, "25": 31, "29": 31,
+                "33": 63, "37": 63, "41": 63, "45": 63,
+                "49": 63, "53": 63, "57": 63, "61": 63,
+                "65": 63, "69": 63, "73": 63, "77": 63,
+                "81": 63, "85": 63, "89": 63, "93": 63,
+                "97": 127, "101": 127, "105": 127, "109": 127,
+                "113": 127, "117": 127, "121": 127, "125": 127,
+                "129": 127, "133": 127, "137": 127, "141": 127,
+                "145": 127, "149": 127, "153": 127, "157": 127,
+                "161": 191
+            };
+        }
+        break;
+    }
+
+    if (center_channel_map[channel])
+        center_channel = center_channel_map[channel];
+
+    return center_channel;
 }
 
 function interface_status_check(iface) {
@@ -201,6 +307,9 @@ function check_current_channel(iface) {
 function hostapd_switch_channel(msg) {
     ulog_info(`[%s] Start switch channel to %d \n`, msg.iface, msg.channel);
 
+    // Channel switch in progress, set flag = 1
+    stats_info_write("/tmp/rrm_chan_switch", 1);
+
     let chan_switch_status = 0;
     let sec_channel_offset = null;
 
@@ -208,7 +317,8 @@ function hostapd_switch_channel(msg) {
     let bandwidth = replace(msg.htmode, /[^0-9]/g, '');
 
     let target_freq = channel_to_freq(msg.band, msg.channel);
-    let center_freq = center_freq_calc(msg.band, target_freq, bandwidth);
+    let center_channel = get_center_channel(msg.channel, msg.band, bandwidth);
+    let center_freq = channel_to_freq(msg.band, center_channel);
     if (bandwidth > 20)
         sec_channel_offset = 1;
 
@@ -245,9 +355,20 @@ function switch_status_check(iface, dfs_enabled_5g_flag) {
         ulog_info(`[%s] 5G radio might need some time to be UP (DFS enabled) \n`, iface);
 
         let p = 0;
-        // Max 65 seconds wait for the DFS enabled interface to be UP
+        // Default max 70 seconds wait for the DFS enabled interface to be UP
         let timer = 70;
 
+        // get real timer from hostapd_cli command
+        let check_cac_time = sprintf('hostapd_cli -i %s status | grep \"cac_time_left_seconds\" | awk -F "=" \'{print $2}\'', iface);
+        let _cac_time = fs.popen(check_cac_time);
+        let cac_time = trim(_cac_time.read('all'));
+        _cac_time.close();
+
+        // if cac_time is a valid number, set timer to cac_time + 5 seconds
+        if (cac_time > 0 && match(cac_time, /^[0-9]+$/)) {
+            timer = int(cac_time) + 5;
+        }
+
         while (p < timer) {
             ulog_info(`[%s] Check#%d \n `, iface, p);
 
@@ -267,6 +388,9 @@ function switch_status_check(iface, dfs_enabled_5g_flag) {
         }
     }
 
+    // Channel switch done, set flag = 0
+    stats_info_write("/tmp/rrm_chan_switch", 0);
+
     let current_chan = check_current_channel(iface);
     return current_chan;
 }
@@ -436,7 +560,7 @@ function random_channel_selection(iface, band, htmode, chan_list_valid) {
     ulog_info(`[%s] Selected channel list from config (default channel list shall be used in case channels haven't been selected) = %s \n`, iface, (chan_list_valid || '[]'));
 
     if (band == '2g' && bw >= 40) {
-        ulog_info(`[%s] It is highly recommended to NOT use %dMHz bandwidth for 2.4G radio \n`, iface, bw);
+        ulog_info(`[%s] It is highly recommended to NOT use %dMHz bandwidth for 2.4G radio (RRM will not work properly) \n`, iface, bw);
     } else if (band == '5g' && bw > 160) {
         ulog_info(`[%s] %dMHz bandwidth not supported for 5G radio. Please use a bandwidth of 160MHz or lower\n`, iface, bw);
     }
@@ -568,9 +692,28 @@ function random_channel_selection(iface, band, htmode, chan_list_valid) {
     return random_channel;
 }
 
+function check_center_channel(chosen_random_channel, current_channel, band, htmode) {
+    let ret = false;
+    let bw = replace(htmode, /[^0-9]/g, '');
+
+    if (band != '2g' || bw != 20) {
+        // for 2G band or 20MHz bandwidth, center channel is the same as the channel
+        let chosen_random_channel_center = get_center_channel(chosen_random_channel, band, bw);
+        let current_channel_center = get_center_channel(current_channel, band, bw);
+
+        ulog_info(`Center channel of the chosen random channel (%d) = %d; Center channel of the current channel (%d) = %d \n`, chosen_random_channel, chosen_random_channel_center, current_channel, current_channel_center);
+
+        if (chosen_random_channel_center == current_channel_center)
+            ret = true;
+    }
+
+    return ret;
+}
+
 function algo_rcs(iface, current_channel, band, htmode, selected_channels) {
     let chosen_random_channel = 0;
     let res = 0;
+    let same_center_channel = false;
 
     // random_channel_selection script will help to select random channel
     chosen_random_channel = random_channel_selection(iface, band, htmode, selected_channels);
@@ -580,8 +723,15 @@ function algo_rcs(iface, current_channel, band, htmode, selected_channels) {
         ulog_info(`[%s] RCS assigned the same channel = %d; Skip channel switch \n`, iface, chosen_random_channel);
         res = 0;
     } else if (chosen_random_channel > 0) {
-        ulog_info(`[%s] RCS done ... random channel found = %d\n`, iface, chosen_random_channel);
-        res = 1;
+        // check if the random channel has the same center channel as the current channel
+        same_center_channel = check_center_channel(chosen_random_channel, current_channel, band, htmode);
+        if (same_center_channel) {
+            ulog_info(`[%s] RCS found channel %d with the same center channel as current channel %d; Skip channel switch \n`, iface, chosen_random_channel, current_channel);
+            res = 0;
+        } else {
+            ulog_info(`[%s] RCS done ... random channel found = %d\n`, iface, chosen_random_channel);
+            res = 1;
+        }
     } else {
         ulog_info(`[%s] RCS scan FAIL. Retry Channel optimization at next cycle \n`, iface);
         res = 0;
@@ -611,6 +761,8 @@ function channel_optimize() {
         return config.interval;
     }
 
+    record_rrm_timestamp();
+
     let current_rf_down = {};
 	let cool_down_f = {};
     let check_all_cool_down = 0;
@@ -924,7 +1076,7 @@ function channel_optimize() {
                             }
                         } else {
                             // revert back to the original channel
-                            ulog_info(`[%s] Channel %d has a cac_time longer than 60 seconds, RRM failed for this interval (you might want to avoid selecting this channel) \n`, radio_iface[l], init_payload.channel);
+                            ulog_info(`[%s] Channel %d may have a cac_time longer than 60 seconds, RRM failed for this interval (you might want to avoid selecting this channel) \n`, radio_iface[l], init_payload.channel);
                         }
                     } else if (selected_algo == "ACS") {
                         let random_wait_time = random_time_calc();
@@ -940,6 +1092,9 @@ function channel_optimize() {
                             check_all_threshold_breach >= 1: threshold breach count exceeded for one or more interfaces
                         */
 
+                        // Channel switch in progress, set flag = 1
+                        stats_info_write("/tmp/rrm_chan_switch", 1);
+
                         // flag to check if 5G radio was restarted
                         let radio_5g_restarted = 0;
 
@@ -1003,6 +1158,10 @@ function channel_optimize() {
                             sleep(30000);
                         }
                     }
+
+                    sleep(5000);
+                    // Channel switch done, set flag = 0
+                    stats_info_write("/tmp/rrm_chan_switch", 0);
                 } else {
                     if (threshold_breach_f[l] != 1) {
                         ulog_info(`[%s] Threshold breach count (=%d) < Allowed consecutive Channel Utilization threshold breach count (=%d), will be checked again in the next interval \n`, radio_iface[l], threshold_breach_count[l], config.consecutive_threshold_breach);
@@ -1016,6 +1175,7 @@ function channel_optimize() {
         }
     }
     ulog_info(`RRM with channel optimization finished; next RRM round starts in %d seconds \n`, config.interval/1000);
+    record_rrm_timestamp();
 
     return config.interval;
 }

feeds/ucentral/rtty/files/rtty.init

@@ -51,7 +51,7 @@ start_rtty() {
 	procd_set_param command $BIN -h $host -I "$id" -a
 	[ -n "$port" ] && procd_append_param command -p "$port"
 	[ -n "$description" ] && procd_append_param command -d "$description"
-	[ "$ssl" = "1" ] && procd_append_param command -s -c /etc/ucentral/cert.pem -k /etc/ucentral/key.pem
+	[ "$ssl" = "1" ] && procd_append_param command -s -c /etc/ucentral/operational.pem -k /etc/ucentral/key.pem
 	[ -n "$token" ] && procd_append_param command -t "$token"
 	[ "$verbose" = "1" ] && procd_append_param command -v
 	[ "$timeout" -eq "0" ] || procd_append_param command -e $timeout

feeds/ucentral/ucentral-client/Makefile

@@ -4,10 +4,10 @@ PKG_NAME:=ucentral-client
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-client.git
-PKG_MIRROR_HASH:=2e28e0aa61b74851c7daf3634ec34d303a603e881e6c5d1fd76c837dea527582
+PKG_MIRROR_HASH:=2935998d6074f0c290d9b96c2988c89aae6f405608f12a0063fa7215498bae9a
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_DATE:=2025-07-08
-PKG_SOURCE_VERSION:=69829f63ea172ce9bd19b7b02073746fe9cf6a52
+PKG_SOURCE_DATE:=2025-08-11
+PKG_SOURCE_VERSION:=549e84e5fea7230c5471d6a3dbddcc7d3152f665
 
 PKG_LICENSE:=BSD-3-Clause
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>

feeds/ucentral/ucentral-client/files/etc/config/ucentral

@@ -6,9 +6,9 @@ config ucentral config
 	option reporting	10
 
 config timeouts timeouts
-	option offline		120
+	option offline		14400
 	option validate		120
-	option orphan		120
+	option orphan		7200
 
 #config event
 #	option type  dhcp

feeds/ucentral/ucentral-schema/Makefile

@@ -4,10 +4,10 @@ PKG_NAME:=ucentral-schema
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-schema.git
-PKG_MIRROR_HASH:=1ad9f7b5d5d1145e3aed14937eef60d6794d821e0244cc8fa824400d3da47f5a
+PKG_MIRROR_HASH:=d36e17c47d793fb3b0181ed92411e31a2be8e0ff6f9fad89d9704146f9f251cb
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_DATE:=2025-07-11
-PKG_SOURCE_VERSION:=5276d0b8b6e83ab57354b0bcbb820de83a91ab88
+PKG_SOURCE_DATE:=2025-09-24
+PKG_SOURCE_VERSION:=100c045af16bc13db7af936a4cf6f675eb651974
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

feeds/ucentral/ucentral-state/files/ucentral-state

@@ -20,9 +20,68 @@ let config;
 let offline_timer;
 let current_state;
 let online = false;
+let leds_off = false;
 
 function self_healing() {
+	let heal_wifi = false;
+	let health_stat = json(fs.readfile('/tmp/ucentral.health'));
+	let last_nw_restart_ts = int(fs.readfile('/tmp/ucentral.nw_restart_ts')) || 0;
+	let time_passed_since_nw_restart = time() - last_nw_restart_ts;
 
+	if (health_stat) {
+		if (health_stat.data.rrm_chanutil == false) {
+			// RRM with Channel utilization abnormal, restart rrmd
+			ulog(LOG_INFO, 'RRM with Channel utilization abnormal, restarting rrmd\n');
+			system('/etc/init.d/rrmd restart');
+		}
+
+		if (health_stat.sanity != 100) {
+			for (let iface in health_stat.data.interfaces) {
+				let iface_data = health_stat.data.interfaces[iface];
+				if (iface_data.ssids) {
+					// one of the VAPs have an issue: flag up!
+					heal_wifi = true;
+					ulog(LOG_INFO, 'Time passed since last network restart = %d seconds\n', time_passed_since_nw_restart);
+					break;
+				}
+			}
+		} else {
+			// all VAPs are healthy, no need to heal anything
+			return;
+		}
+	}
+
+	if (fs.stat('/tmp/rrm_timestamp')) {
+		let rrm_chan_switch_flag = int(fs.readfile('/tmp/rrm_chan_switch')) || 0;
+		let last_rrm_timestamp = int(fs.readfile('/tmp/rrm_timestamp'));
+		let time_passed_since_rrm = time() - last_rrm_timestamp;
+
+		if (rrm_chan_switch_flag == 1) {
+			// RRM chan switch in progress, do not restart network!
+			ulog(LOG_INFO, 'RRM channel switch in progress, cannot restart network \n');
+			heal_wifi = false;
+		}
+
+		if (time_passed_since_rrm < 180) {
+			// RRM in progress, do not restart network!
+			ulog(LOG_INFO, 'RRM with Channel utilization may still be in progress, cannot restart network \n');
+			heal_wifi = false;
+		}
+	}
+
+	// keep a gap of at least 5 minutes between network restarts
+	if (heal_wifi && time_passed_since_nw_restart > 300) {
+		ulog(LOG_INFO, 'Restarting network \n');
+		// update network restart timestamp
+		let f = fs.open("/tmp/ucentral.nw_restart_ts", "w");
+		if (f) {
+			f.write(time());
+			f.close();
+		}
+
+		// restart network
+		system('/etc/init.d/network restart');
+	}
 }
 
 let healthcheck;
@@ -42,7 +101,7 @@ healthcheck = {
 	},
 
 	spawn: function() {
-		ulog(LOG_INFO, 'healtcheck execute\n');
+		ulog(LOG_INFO, 'healthcheck execute\n');
 		healthcheck.pid = uloop.process('/usr/share/ucentral/health.uc', [], {}, healthcheck.complete);
 	},
 };
@@ -90,6 +149,13 @@ function online_handler() {
 
 function config_load() {
 	ulog(LOG_INFO, 'loading config\n');
+
+	uci.load('system');
+	let led_off_cfg = uci.get("system", "@system[0]", "leds_off");
+	if (led_off_cfg == 1) {
+		leds_off = true;
+	}
+
 	uci.load('state');
 	config = uci.get_all('state');
 
@@ -133,7 +199,7 @@ function led_find(alias) {
 function factory_reset_timeout() {
 	let led = led_find('led-running');
 	if (led)
-		led_write(led, 'trigger', 'default-on');
+		led_write(led, 'trigger', leds-off ? 'none' : 'default-on');
 }
 
 let blink_timer;
@@ -152,7 +218,7 @@ let state_handler = {
 	offline: function() {
 		online = false;
 		let led = led_find('led-running');
-		if (led)
+		if (!leds_off && led)
 			led_write(led, 'trigger', 'heartbeat');
 		if (config.ui.offline_trigger) {
 			if (offline_timer)
@@ -165,7 +231,7 @@ let state_handler = {
 	online: function() {
 		online = true;
 		let led = led_find('led-running');
-		if (led)
+		if (!leds_off && led)
 			led_write(led, 'trigger', 'default-on');
 		online_handler();
 		return 0;
@@ -207,7 +273,7 @@ let ubus_methods = {
 			current_state = req.args.state;
 			blink_timeout();
 			ulog(LOG_INFO, 'set state -> ' + req.args.state + '\n');
-			
+
 			return state_handler[req.args.state](req.args);
 		},
 		args: {

feeds/ucentral/ucentral-tools/Makefile

@@ -3,12 +3,6 @@ include $(TOPDIR)/rules.mk
 PKG_NAME:=ucentral-tools
 PKG_RELEASE:=1
 
-PKG_SOURCE_URL=https://github.com/blogic/ucentral-tools.git
-PKG_MIRROR_HASH:=9ae6a0cd431595871c233550427c4043c2ba7ddb3c5d87e46ab74a03b2b5a947
-PKG_SOURCE_PROTO:=git
-PKG_SOURCE_DATE:=2021-01-28
-PKG_SOURCE_VERSION:=b013fc636e48d407870a46aaa68a09ed74de8d6f
-
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

feeds/ucentral/ucentral-tools/src/CMakeLists.txt

@@ -0,0 +1,36 @@
+cmake_minimum_required(VERSION 2.6)
+
+PROJECT(openwifi-tools C)
+INCLUDE(GNUInstallDirs)
+ADD_DEFINITIONS(-Os -ggdb -Wall -Werror --std=gnu99 -Wmissing-declarations)
+
+SET(CMAKE_SHARED_LIBRARY_LINK_C_FLAGS "")
+
+ADD_EXECUTABLE(firstcontact firstcontact.c)
+TARGET_LINK_LIBRARIES(firstcontact curl crypto ssl ubox)
+INSTALL(TARGETS firstcontact
+	RUNTIME DESTINATION ${CMAKE_INSTALL_SBINDIR}
+)
+
+ADD_EXECUTABLE(dhcpdiscover dhcpdiscover.c)
+INSTALL(TARGETS dhcpdiscover
+	RUNTIME DESTINATION ${CMAKE_INSTALL_SBINDIR}
+)
+
+ADD_EXECUTABLE(dnsprobe dnsprobe.c)
+TARGET_LINK_LIBRARIES(dnsprobe ubox resolv)
+INSTALL(TARGETS dnsprobe
+	RUNTIME DESTINATION ${CMAKE_INSTALL_SBINDIR}
+)
+
+ADD_EXECUTABLE(radiusprobe radiusprobe.c)
+TARGET_LINK_LIBRARIES(radiusprobe radcli)
+INSTALL(TARGETS radiusprobe
+	RUNTIME DESTINATION ${CMAKE_INSTALL_SBINDIR}
+)
+
+ADD_EXECUTABLE(ip-collide ip-collide.c)
+TARGET_LINK_LIBRARIES(ip-collide ubox)
+INSTALL(TARGETS ip-collide
+	RUNTIME DESTINATION ${CMAKE_INSTALL_SBINDIR}
+)

feeds/ucentral/ucentral-tools/src/dnsprobe.c

@@ -0,0 +1,690 @@
+/*
+ * nslookup_lede - musl compatible replacement for busybox nslookup
+ *
+ * Copyright (C) 2017 Jo-Philipp Wich <jo@mein.io>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+//config:config NSLOOKUP_OPENWRT
+//config:	bool "nslookup_openwrt"
+//config:	depends on !NSLOOKUP
+//config:	default y
+//config:	help
+//config:	  nslookup is a tool to query Internet name servers (LEDE flavor).
+//config:
+//config:config FEATURE_NSLOOKUP_OPENWRT_LONG_OPTIONS
+//config:       bool "Enable long options"
+//config:       default y
+//config:       depends on NSLOOKUP_OPENWRT && LONG_OPTS
+//config:       help
+//config:         Support long options for the nslookup applet.
+
+//applet:IF_NSLOOKUP_OPENWRT(APPLET(nslookup, BB_DIR_USR_BIN, BB_SUID_DROP))
+
+//kbuild:lib-$(CONFIG_NSLOOKUP_OPENWRT) += nslookup_lede.o
+
+//usage:#define nslookup_lede_trivial_usage
+//usage:       "[HOST] [SERVER]"
+//usage:#define nslookup_lede_full_usage "\n\n"
+//usage:       "Query the nameserver for the IP address of the given HOST\n"
+//usage:       "optionally using a specified DNS server"
+//usage:
+//usage:#define nslookup_lede_example_usage
+//usage:       "$ nslookup localhost\n"
+//usage:       "Server:     default\n"
+//usage:       "Address:    default\n"
+//usage:       "\n"
+//usage:       "Name:       debian\n"
+//usage:       "Address:    127.0.0.1\n"
+
+#include <stdio.h>
+#include <resolv.h>
+#include <string.h>
+#include <errno.h>
+#include <time.h>
+#include <poll.h>
+#include <unistd.h>
+#include <stdlib.h>
+#include <sys/socket.h>
+#include <arpa/inet.h>
+#include <net/if.h>
+#include <netdb.h>
+
+#include <libubox/ulog.h>
+
+#define ENABLE_FEATURE_IPV6	1
+
+typedef struct len_and_sockaddr {
+	socklen_t len;
+	union {
+		struct sockaddr sa;
+		struct sockaddr_in sin;
+#if ENABLE_FEATURE_IPV6
+		struct sockaddr_in6 sin6;
+#endif
+	} u;
+} len_and_sockaddr;
+
+struct ns {
+	const char *name;
+	len_and_sockaddr addr;
+	int failures;
+	int replies;
+};
+
+struct query {
+	const char *name;
+	size_t qlen, rlen;
+	unsigned char query[512], reply[512];
+	unsigned long latency;
+	int rcode, n_ns;
+};
+
+static const char *rcodes[] = {
+	"NOERROR",
+	"FORMERR",
+	"SERVFAIL",
+	"NXDOMAIN",
+	"NOTIMP",
+	"REFUSED",
+	"YXDOMAIN",
+	"YXRRSET",
+	"NXRRSET",
+	"NOTAUTH",
+	"NOTZONE",
+	"RESERVED11",
+	"RESERVED12",
+	"RESERVED13",
+	"RESERVED14",
+	"RESERVED15",
+	"BADVERS"
+};
+
+static unsigned int default_port = 53;
+static unsigned int default_retry = 1;
+static unsigned int default_timeout = 2;
+
+
+static int parse_reply(const unsigned char *msg, size_t len, int *bb_style_counter)
+{
+	ns_msg handle;
+	ns_rr rr;
+	int i, n, rdlen;
+	const char *format = NULL;
+	char astr[INET6_ADDRSTRLEN], dname[MAXDNAME];
+	const unsigned char *cp;
+
+	if (ns_initparse(msg, len, &handle) != 0) {
+		//fprintf(stderr, "Unable to parse reply: %s\n", strerror(errno));
+		return -1;
+	}
+
+	for (i = 0; i < ns_msg_count(handle, ns_s_an); i++) {
+		if (ns_parserr(&handle, ns_s_an, i, &rr) != 0) {
+			//fprintf(stderr, "Unable to parse resource record: %s\n", strerror(errno));
+			return -1;
+		}
+
+		rdlen = ns_rr_rdlen(rr);
+
+		switch (ns_rr_type(rr))
+		{
+		case ns_t_a:
+			if (rdlen != 4) {
+				//fprintf(stderr, "Unexpected A record length\n");
+				return -1;
+			}
+			inet_ntop(AF_INET, ns_rr_rdata(rr), astr, sizeof(astr));
+			printf("Name:\t%s\nAddress: %s\n", ns_rr_name(rr), astr);
+			break;
+
+#if ENABLE_FEATURE_IPV6
+		case ns_t_aaaa:
+			if (rdlen != 16) {
+				//fprintf(stderr, "Unexpected AAAA record length\n");
+				return -1;
+			}
+			inet_ntop(AF_INET6, ns_rr_rdata(rr), astr, sizeof(astr));
+			printf("%s\thas AAAA address %s\n", ns_rr_name(rr), astr);
+			break;
+#endif
+
+		case ns_t_ns:
+			if (!format)
+				format = "%s\tnameserver = %s\n";
+			/* fall through */
+
+		case ns_t_cname:
+			if (!format)
+				format = "%s\tcanonical name = %s\n";
+			/* fall through */
+
+		case ns_t_ptr:
+			if (!format)
+				format = "%s\tname = %s\n";
+			if (ns_name_uncompress(ns_msg_base(handle), ns_msg_end(handle),
+				ns_rr_rdata(rr), dname, sizeof(dname)) < 0) {
+				//fprintf(stderr, "Unable to uncompress domain: %s\n", strerror(errno));
+				return -1;
+			}
+			printf(format, ns_rr_name(rr), dname);
+			break;
+
+		case ns_t_mx:
+			if (rdlen < 2) {
+				fprintf(stderr, "MX record too short\n");
+				return -1;
+			}
+			n = ns_get16(ns_rr_rdata(rr));
+			if (ns_name_uncompress(ns_msg_base(handle), ns_msg_end(handle),
+				ns_rr_rdata(rr) + 2, dname, sizeof(dname)) < 0) {
+				//fprintf(stderr, "Cannot uncompress MX domain: %s\n", strerror(errno));
+				return -1;
+			}
+			printf("%s\tmail exchanger = %d %s\n", ns_rr_name(rr), n, dname);
+			break;
+
+		case ns_t_txt:
+			if (rdlen < 1) {
+				//fprintf(stderr, "TXT record too short\n");
+				return -1;
+			}
+			n = *(unsigned char *)ns_rr_rdata(rr);
+			if (n > 0) {
+				memset(dname, 0, sizeof(dname));
+				memcpy(dname, ns_rr_rdata(rr) + 1, n);
+				printf("%s\ttext = \"%s\"\n", ns_rr_name(rr), dname);
+			}
+			break;
+
+		case ns_t_soa:
+			if (rdlen < 20) {
+				//fprintf(stderr, "SOA record too short\n");
+				return -1;
+			}
+
+			printf("%s\n", ns_rr_name(rr));
+
+			cp = ns_rr_rdata(rr);
+			n = ns_name_uncompress(ns_msg_base(handle), ns_msg_end(handle),
+			                       cp, dname, sizeof(dname));
+
+			if (n < 0) {
+				//fprintf(stderr, "Unable to uncompress domain: %s\n", strerror(errno));
+				return -1;
+			}
+
+			printf("\torigin = %s\n", dname);
+			cp += n;
+
+			n = ns_name_uncompress(ns_msg_base(handle), ns_msg_end(handle),
+			                       cp, dname, sizeof(dname));
+
+			if (n < 0) {
+				//fprintf(stderr, "Unable to uncompress domain: %s\n", strerror(errno));
+				return -1;
+			}
+
+			printf("\tmail addr = %s\n", dname);
+			cp += n;
+
+			printf("\tserial = %lu\n", ns_get32(cp));
+			cp += 4;
+
+			printf("\trefresh = %lu\n", ns_get32(cp));
+			cp += 4;
+
+			printf("\tretry = %lu\n", ns_get32(cp));
+			cp += 4;
+
+			printf("\texpire = %lu\n", ns_get32(cp));
+			cp += 4;
+
+			printf("\tminimum = %lu\n", ns_get32(cp));
+			break;
+
+		default:
+			break;
+		}
+	}
+
+	return i;
+}
+
+static int parse_nsaddr(const char *addrstr, len_and_sockaddr *lsa)
+{
+	char *eptr, *hash, ifname[IFNAMSIZ];
+	unsigned int port = default_port;
+	unsigned int scope = 0;
+
+	hash = strchr(addrstr, '#');
+
+	if (hash) {
+		*hash++ = '\0';
+		port = strtoul(hash, &eptr, 10);
+
+		if (eptr == hash || *eptr != '\0' || port > 65535) {
+			errno = EINVAL;
+			return -1;
+		}
+	}
+
+	hash = strchr(addrstr, '%');
+
+	if (hash) {
+		for (eptr = ++hash; *eptr != '\0' && *eptr != '#'; eptr++) {
+			if ((eptr - hash) >= IFNAMSIZ) {
+				errno = ENODEV;
+				return -1;
+			}
+
+			ifname[eptr - hash] = *eptr;
+		}
+
+		ifname[eptr - hash] = '\0';
+		scope = if_nametoindex(ifname);
+
+		if (scope == 0) {
+			errno = ENODEV;
+			return -1;
+		}
+	}
+
+#if ENABLE_FEATURE_IPV6
+	if (inet_pton(AF_INET6, addrstr, &lsa->u.sin6.sin6_addr)) {
+		lsa->u.sin6.sin6_family = AF_INET6;
+		lsa->u.sin6.sin6_port = htons(port);
+		lsa->u.sin6.sin6_scope_id = scope;
+		lsa->len = sizeof(lsa->u.sin6);
+		return 0;
+	}
+#endif
+
+	if (!scope && inet_pton(AF_INET, addrstr, &lsa->u.sin.sin_addr)) {
+		lsa->u.sin.sin_family = AF_INET;
+		lsa->u.sin.sin_port = htons(port);
+		lsa->len = sizeof(lsa->u.sin);
+		return 0;
+	}
+
+	errno = EINVAL;
+	return -1;
+}
+
+static unsigned long mtime(void)
+{
+	struct timespec ts;
+	clock_gettime(CLOCK_REALTIME, &ts);
+	return (unsigned long)ts.tv_sec * 1000 + ts.tv_nsec / 1000000;
+}
+
+#if ENABLE_FEATURE_IPV6
+static void to_v4_mapped(len_and_sockaddr *a)
+{
+	if (a->u.sa.sa_family != AF_INET)
+		return;
+
+	memcpy(a->u.sin6.sin6_addr.s6_addr + 12,
+	       &a->u.sin.sin_addr, 4);
+
+	memcpy(a->u.sin6.sin6_addr.s6_addr,
+	       "\0\0\0\0\0\0\0\0\0\0\xff\xff", 12);
+
+	a->u.sin6.sin6_family = AF_INET6;
+	a->u.sin6.sin6_flowinfo = 0;
+	a->u.sin6.sin6_scope_id = 0;
+	a->len = sizeof(a->u.sin6);
+}
+#endif
+
+
+/*
+ * Function logic borrowed & modified from musl libc, res_msend.c
+ */
+
+static int send_queries(struct ns *ns, int n_ns, struct query *queries, int n_queries)
+{
+	int fd;
+	int timeout = default_timeout * 1000, retry_interval, servfail_retry = 0;
+	len_and_sockaddr from = { };
+#if ENABLE_FEATURE_IPV6
+	int one = 1;
+#endif
+	int recvlen = 0;
+	int n_replies = 0;
+	struct pollfd pfd;
+	unsigned long t0, t1, t2;
+	int nn, qn, next_query = 0;
+
+	from.u.sa.sa_family = AF_INET;
+	from.len = sizeof(from.u.sin);
+
+#if ENABLE_FEATURE_IPV6
+	for (nn = 0; nn < n_ns; nn++) {
+		if (ns[nn].addr.u.sa.sa_family == AF_INET6) {
+			from.u.sa.sa_family = AF_INET6;
+			from.len = sizeof(from.u.sin6);
+			break;
+		}
+	}
+#endif
+
+	/* Get local address and open/bind a socket */
+	fd = socket(from.u.sa.sa_family, SOCK_DGRAM|SOCK_CLOEXEC|SOCK_NONBLOCK, 0);
+
+#if ENABLE_FEATURE_IPV6
+	/* Handle case where system lacks IPv6 support */
+	if (fd < 0 && from.u.sa.sa_family == AF_INET6 && errno == EAFNOSUPPORT) {
+		fd = socket(AF_INET, SOCK_DGRAM|SOCK_CLOEXEC|SOCK_NONBLOCK, 0);
+		from.u.sa.sa_family = AF_INET;
+	}
+#endif
+
+	if (fd < 0)
+		return -1;
+
+	if (bind(fd, &from.u.sa, from.len) < 0) {
+		close(fd);
+		return -1;
+	}
+
+#if ENABLE_FEATURE_IPV6
+	/* Convert any IPv4 addresses in a mixed environment to v4-mapped */
+	if (from.u.sa.sa_family == AF_INET6) {
+		setsockopt(fd, IPPROTO_IPV6, IPV6_V6ONLY, &one, sizeof(one));
+
+		for (nn = 0; nn < n_ns; nn++)
+			to_v4_mapped(&ns[nn].addr);
+	}
+#endif
+
+	pfd.fd = fd;
+	pfd.events = POLLIN;
+	retry_interval = timeout / default_retry;
+	t0 = t2 = mtime();
+	t1 = t2 - retry_interval;
+
+	for (; t2 - t0 < timeout; t2 = mtime()) {
+		if (t2 - t1 >= retry_interval) {
+			for (qn = 0; qn < n_queries; qn++) {
+				if (queries[qn].rlen)
+					continue;
+
+				for (nn = 0; nn < n_ns; nn++) {
+					sendto(fd, queries[qn].query, queries[qn].qlen,
+					       MSG_NOSIGNAL, &ns[nn].addr.u.sa, ns[nn].addr.len);
+				}
+			}
+
+			t1 = t2;
+			servfail_retry = 2 * n_queries;
+		}
+
+		/* Wait for a response, or until time to retry */
+		if (poll(&pfd, 1, t1+retry_interval-t2) <= 0)
+			continue;
+
+		while (1) {
+			recvlen = recvfrom(fd, queries[next_query].reply,
+			                   sizeof(queries[next_query].reply), 0,
+			                   &from.u.sa, &from.len);
+
+			/* read error */
+			if (recvlen < 0)
+				break;
+
+			/* Ignore non-identifiable packets */
+			if (recvlen < 4)
+				continue;
+
+			/* Ignore replies from addresses we didn't send to */
+			for (nn = 0; nn < n_ns; nn++)
+				if (memcmp(&from.u.sa, &ns[nn].addr.u.sa, from.len) == 0)
+					break;
+
+			if (nn >= n_ns)
+				continue;
+
+			/* Find which query this answer goes with, if any */
+			for (qn = next_query; qn < n_queries; qn++)
+				if (!memcmp(queries[next_query].reply, queries[qn].query, 2))
+					break;
+
+			if (qn >= n_queries || queries[qn].rlen)
+				continue;
+
+			queries[qn].rcode = queries[next_query].reply[3] & 15;
+			queries[qn].latency = mtime() - t0;
+			queries[qn].n_ns = nn;
+
+			ns[nn].replies++;
+
+			/* Only accept positive or negative responses;
+			 * retry immediately on server failure, and ignore
+			 * all other codes such as refusal. */
+			switch (queries[qn].rcode) {
+			case 0:
+			case 3:
+				break;
+
+			case 2:
+				if (servfail_retry && servfail_retry--) {
+					ns[nn].failures++;
+					sendto(fd, queries[qn].query, queries[qn].qlen,
+					       MSG_NOSIGNAL, &ns[nn].addr.u.sa, ns[nn].addr.len);
+				}
+				/* fall through */
+
+			default:
+				continue;
+			}
+
+			/* Store answer */
+			n_replies++;
+
+			queries[qn].rlen = recvlen;
+
+			if (qn == next_query) {
+				while (next_query < n_queries) {
+					if (!queries[next_query].rlen)
+						break;
+
+					next_query++;
+				}
+			}
+			else {
+				memcpy(queries[qn].reply, queries[next_query].reply, recvlen);
+			}
+
+			if (next_query >= n_queries)
+				return n_replies;
+		}
+	}
+
+	return n_replies;
+}
+
+static struct ns *add_ns(struct ns **ns, int *n_ns, const char *addr)
+{
+	char portstr[sizeof("65535")], *p;
+	len_and_sockaddr a = { };
+	struct ns *tmp;
+	struct addrinfo *ai, *aip, hints = {
+		.ai_flags = AI_NUMERICSERV,
+		.ai_socktype = SOCK_DGRAM
+	};
+
+	if (parse_nsaddr(addr, &a)) {
+		/* Maybe we got a domain name, attempt to resolve it using the standard
+		 * resolver routines */
+
+		p = strchr(addr, '#');
+		snprintf(portstr, sizeof(portstr), "%hu",
+		         (unsigned short)(p ? strtoul(p, NULL, 10) : default_port));
+
+		if (!getaddrinfo(addr, portstr, &hints, &ai)) {
+			for (aip = ai; aip; aip = aip->ai_next) {
+				if (aip->ai_addr->sa_family != AF_INET &&
+				    aip->ai_addr->sa_family != AF_INET6)
+					continue;
+
+#if ! ENABLE_FEATURE_IPV6
+				if (aip->ai_addr->sa_family != AF_INET)
+					continue;
+#endif
+
+				tmp = realloc(*ns, sizeof(**ns) * (*n_ns + 1));
+
+				if (!tmp)
+					return NULL;
+
+				*ns = tmp;
+
+				(*ns)[*n_ns].name = addr;
+				(*ns)[*n_ns].replies = 0;
+				(*ns)[*n_ns].failures = 0;
+				(*ns)[*n_ns].addr.len = aip->ai_addrlen;
+
+				memcpy(&(*ns)[*n_ns].addr.u.sa, aip->ai_addr, aip->ai_addrlen);
+
+				(*n_ns)++;
+			}
+
+			freeaddrinfo(ai);
+
+			return &(*ns)[*n_ns];
+		}
+
+		return NULL;
+	}
+
+	tmp = realloc(*ns, sizeof(**ns) * (*n_ns + 1));
+
+	if (!tmp)
+		return NULL;
+
+	*ns = tmp;
+
+	(*ns)[*n_ns].addr = a;
+	(*ns)[*n_ns].name = addr;
+	(*ns)[*n_ns].replies = 0;
+	(*ns)[*n_ns].failures = 0;
+
+	return &(*ns)[(*n_ns)++];
+}
+
+static struct query *add_query(struct query **queries, int *n_queries,
+                               int type, const char *dname)
+{
+	struct query *tmp;
+	ssize_t qlen;
+
+	tmp = realloc(*queries, sizeof(**queries) * (*n_queries + 1));
+
+	if (!tmp)
+		return NULL;
+
+	memset(&tmp[*n_queries], 0, sizeof(*tmp));
+
+	qlen = res_mkquery(QUERY, dname, C_IN, type, NULL, 0, NULL,
+	                   tmp[*n_queries].query, sizeof(tmp[*n_queries].query));
+
+	tmp[*n_queries].qlen = qlen;
+	tmp[*n_queries].name = dname;
+	*queries = tmp;
+
+	return &tmp[(*n_queries)++];
+}
+
+int main(int argc, char **argv)
+{
+	int rc = 1;
+	struct ns *ns = NULL;
+	struct query *queries = NULL;
+	int n_ns = 0, n_queries = 0;
+	int c = 0;
+
+	char *url = "telecominfraproject.com";
+	char *server = "127.0.0.1";
+	int v6 = 0;
+
+	while (1) {
+		int option = getopt(argc, argv, "u:s:i:6");
+
+		if (option == -1)
+			break;
+
+		switch (option) {
+		case '6':
+			v6 = 1;
+			break;
+		case 'u':
+			url = optarg;
+			break;
+		case 's':
+			server = optarg;
+			break;
+		default:
+		case 'h':
+			printf("Usage: dnsprobe OPTIONS\n"
+			       "  -6 - use ipv6\n"
+			       "  -u <url>\n"
+			       "  -s <server>\n");
+			return -1;
+		}
+	}
+
+	ulog_open(ULOG_SYSLOG | ULOG_STDIO, LOG_DAEMON, "dnsprobe");
+
+	ULOG_INFO("attempting to probe dns - %s %s %s\n",
+		url, server, v6 ? "ipv6" : "");
+
+
+	add_query(&queries, &n_queries, v6 ? T_AAAA : T_A, url);
+
+	add_ns(&ns, &n_ns, server);
+
+	rc = send_queries(&ns[0], 1, queries, n_queries);
+	if (rc <= 0) {
+		fprintf(stderr, "Failed to send queries: %s\n", strerror(errno));
+		rc = -1;
+		goto out;
+	}
+
+	if (queries[0].rcode != 0) {
+		printf("** server can't find %s: %s\n", queries[0].name,
+		rcodes[queries[0].rcode]);
+		goto out;
+	}
+
+	if (queries[0].rlen) {
+		c = parse_reply(queries[0].reply, queries[0].rlen, NULL);
+	}
+
+	if (c == 0)
+		printf("*** Can't find %s: No answer\n", queries[0].name);
+	else if (c < 0)
+		printf("*** Can't find %s: Parse error\n", queries[0].name);
+	else
+		rc = 0;
+
+out:
+	if (n_ns)
+		free(ns);
+
+	if (n_queries)
+		free(queries);
+
+	return rc;
+}