WIFI-14917 Add a package to backup specific log files.

Signed-off-by: jackcybertan <jack.tsai@cybertan.com.tw>

feeds/ipq807x_v5.4/ath11k-wifi/Makefile

@@ -47,6 +47,8 @@ ALLWIFIBOARDS:= \
 	indio-um-310ax-v1 \
 	indio-um-510axp-v1 \
 	indio-um-510axm-v1 \
+	indio-um-325ax-v2 \
+	indio-um-525axp \
 	muxi-ap3220l \
 	plasmacloud-pax1800 \
 	wallys-dr5018 \
@@ -441,6 +443,8 @@ $(eval $(call generate-ath11k-wifi-package,liteon-wpx8324,Liteon WPX8324))
 $(eval $(call generate-ath11k-wifi-package,indio-um-310ax-v1,Indio UM-310AX V1))
 $(eval $(call generate-ath11k-wifi-package,indio-um-510axp-v1,Indio UM-510AXP V1))
 $(eval $(call generate-ath11k-wifi-package,indio-um-510axm-v1,Indio UM-510AXM V1))
+$(eval $(call generate-ath11k-wifi-package,indio-um-325ax-v2,Indio UM-325AX V2))
+$(eval $(call generate-ath11k-wifi-package,indio-um-525axp,Indio UM-525AXP))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630c-311g,Sonicfi RAP630C 311G))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630w-311g,Sonicfi RAP630W 311G))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630w-312g,Sonicfi RAP630W 312G))

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/board.d/01_leds

@@ -16,6 +16,13 @@ edgecore,eap104)
 	ucidef_set_led_netdev "wan" "wan" "yellow:uplink" "eth0"
         ucidef_set_led_default "power" "POWER" "green:power" "on"
 	;;
+indio,um-325ax-v2|\
+indio,um-525axp)
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wifi2" "phy0tpt"
+	ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wifi5" "phy1tpt"
+	ucidef_set_led_netdev "wan" "wan" "yellow:uplink" "eth0"
+        ucidef_set_led_default "power" "POWER" "green:power" "on"
+	;;
 cig,wf186h|\
 cig,wf186w)
         ucidef_set_led_default "power" "POWER" "green:status" "on"

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/board.d/02_network

@@ -48,6 +48,13 @@ qcom_setup_interfaces()
 		ucidef_add_switch "switch1" \
 			"6u@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
 		;;
+	indio,um-325ax-v2|\
+	indio,um-525axp)
+		ucidef_set_interface_wan "eth1"
+		ucidef_set_interface_lan "eth0"
+		ucidef_add_switch "switch1" \
+			"6@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
+		;;
 	emplus,wap385c|\
 	hfcl,ion4x_w|\
 	hfcl,ion4xi_w)

feeds/ipq807x_v5.4/ipq50xx/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -142,6 +142,8 @@ ath11k/IPQ5018/hw1.0/caldata.bin)
 	emplus,wap385c|\
 	hfcl,ion4x_w|\
 	hfcl,ion4xi_w|\
+	indio,um-325ax-v2|\
+	indio,um-525axp|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
 	optimcloud,d50|\
@@ -183,6 +185,8 @@ ath11k/qcn6122/hw1.0/caldata_1.bin)
 	;;
 ath11k/qcn6122/hw1.0/caldata_2.bin)
 	case "$board" in
+	indio,um-325ax-v2|\
+	indio,um-525axp|\
 	wallys,dr5018|\
 	edgecore,eap104|\
 	edgecore,oap101-6e|\
@@ -234,6 +238,8 @@ ath11k-macs)
 	edgecore,oap101|\
 	edgecore,oap101-6e|\
 	edgecore,oap101e-6e|\
+	indio,um-325ax-v2|\
+	indio,um-525axp|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
 	optimcloud,d50|\

feeds/ipq807x_v5.4/ipq50xx/base-files/lib/upgrade/platform.sh

@@ -81,6 +81,8 @@ platform_check_image() {
 	wallys,dr5018|\
 	hfcl,ion4x_w|\
 	hfcl,ion4xi_w|\
+	indio,um-325ax-v2|\
+	indio,um-525axp|\
 	optimcloud,d60|\
 	optimcloud,d60-5g|\
 	optimcloud,d50|\
@@ -107,6 +109,8 @@ platform_do_upgrade() {
 
 	board=$(board_name)
 	case $board in
+	indio,um-325ax-v2|\
+	indio,um-525axp|\
 	edgecore,oap101|\
 	edgecore,oap101-6e|\
 	edgecore,oap101e|\

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-indio-um-325ax-v2.dts

@@ -0,0 +1,941 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "ipq5018.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "Indio UM-325AX V2";
+	compatible = "indio,um-325ax-v2", "qcom,ipq5018-mp03.5-c1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+                //led-failsafe = &led_red;
+                //led-running = &led_green;
+                //led-upgrade = &led_green;
+                //led-gateway = &led_blue;
+                //led-factory = &led_blue;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+	#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	#endif
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*                   256 MB Profile
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |           8MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x40800000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D100000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D300000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4E400000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4F300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4F400000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x4500000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x1400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xD00000>;
+		};
+
+		m3_dump: m3_dump@4D100000 {
+			no-map;
+			reg = <0x0 0x4D100000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E200000 {
+			no-map;
+			reg = <0x0 0x4E200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E300000 {
+			no-map;
+			reg = <0x0 0x4E300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E400000 {
+			no-map;
+			reg = <0x0 0x4E400000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4F300000 {
+			no-map;
+			reg = <0x0 0x4F300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F400000 {
+			no-map;
+			reg = <0x0 0x4F400000 0x0 0x100000>;
+		};
+		
+	#else
+	/*                 512MB/1GB Profiles
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x41000000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          14MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  Caldb   |  0x4D400000  |           2MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D600000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E600000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E700000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  Caldb   |  0x4E800000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4ED00000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4FD00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4FE00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  Caldb   |  0x4FF00000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x5400000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 01400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xE00000>;
+		};
+
+		m3_dump: m3_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0x100000>;
+		};
+
+		q6_caldb_region: q6_caldb_region@4D400000 {
+			no-map;
+			reg = <0x0 0x4D400000 0x0 0x200000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D600000 {
+			no-map;
+			reg = <0x0 0x4D600000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E600000 {
+			no-map;
+			reg = <0x0 0x4E600000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E700000 {
+			no-map;
+			reg = <0x0 0x4E700000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_1: q6_qcn6122_caldb_1@4E800000 {
+			no-map;
+			reg = <0x0 0x4E800000 0x0 0x500000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E900000 {
+			no-map;
+			reg = <0x0 0x4ED00000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4FD00000 {
+			no-map;
+			reg = <0x0 0x4FD00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4FE00000 {
+			no-map;
+			reg = <0x0 0x4FE00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_2: q6_qcn6122_caldb_2@4FF00000 {
+			no-map;
+			reg = <0x0 0x4FF00000 0x0 0x500000>;
+		};
+
+	#endif
+	};
+
+	soc {
+		gpio-watchdog {
+			compatible = "linux,wdt-gpio";
+			gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
+			hw_algo = "toggle";
+			hw_margin_ms = <5000>;
+			always-running;
+		};
+
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+
+			ethernet-phy@0 {
+				reg = <28>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x1>;
+			ess-switch@0x39c00000 {
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+						mdiobus = <&mdio0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <0x1c>;
+						mdiobus = <&mdio1>;
+						port_mac_sel = "QGMAC_PORT";
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+				ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x28>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <28>;
+					};
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <28>;
+			mdio-bus = <&mdio1>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		qcom,test@0 {
+			status = "ok";
+		};
+
+		nss-macsec1 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <0x1c>;
+			mdiobus = <&mdio1>;
+		};
+
+		lpass: lpass@0xA000000{
+			status = "disabled";
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		pcm_lb: pcm_lb@0 {
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio22", "gpio24", "gpio23", "gpio25";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+			pins = "gpio9";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_cs {
+			pins = "gpio8";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_0 {
+			pins = "gpio7";
+			function = "qspi0";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_1 {
+			pins = "gpio6";
+			function = "qspi1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_2 {
+			pins = "gpio5";
+			function = "qspi2";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_3 {
+			pins = "gpio4";
+			function = "qspi3";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+audio_pins: audio_pinmux {
+};
+        leds_pins: leds_pins {
+                led_5g {
+                        pins = "gpio34";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_2g {
+                        pins = "gpio33";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_sys {
+                        pins = "gpio26";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+		led_onekey {
+                        pins = "gpio28";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+        };
+};
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+        leds {
+                compatible = "gpio-leds";
+                pinctrl-0 = <&leds_pins>;
+                pinctrl-names = "default";
+
+                led_blue: led@34 {
+                        label = "led_5g";
+                        gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_5g";
+                        default-state = "off";
+                };
+                led_green: led@33 {
+                        label = "led_2g";
+                        gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_2g";
+                        default-state = "off";
+                };
+                led_red: led@26 {
+                        label = "led_sys";
+                        gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_sys";
+                        default-state = "off";
+                };
+		led@28 {
+                        label = "led_onekey";
+                        gpios = <&tlmm 28 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_onekey";
+                        default-state = "off";
+                };
+        };
+};
+
+&q6v5_wcss {
+	compatible = "qcom,ipq5018-q6-mpd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	firmware = "IPQ5018/q6_fw.mdt";
+	reg = <0x0cd00000 0x4040>,
+		<0x1938000 0x8>,
+		<0x193d204 0x4>;
+	reg-names = "qdsp6",
+			"tcsr-msip",
+			"tcsr-q6";
+	resets = <&gcc GCC_WCSSAON_RESET>,
+			<&gcc GCC_WCSS_Q6_BCR>;
+
+	reset-names = "wcss_aon_reset",
+			"wcss_q6_reset";
+
+	clocks = <&gcc GCC_Q6_AXIS_CLK>,
+		<&gcc GCC_WCSS_ECAHB_CLK>,
+		<&gcc GCC_Q6_AXIM_CLK>,
+		<&gcc GCC_Q6_AXIM2_CLK>,
+		<&gcc GCC_Q6_AHB_CLK>,
+		<&gcc GCC_Q6_AHB_S_CLK>,
+		<&gcc GCC_WCSS_AXI_S_CLK>;
+	clock-names = "gcc_q6_axis_clk",
+		"gcc_wcss_ecahb_clk",
+		"gcc_q6_axim_clk",
+		"gcc_q6_axim2_clk",
+		"gcc_q6_ahb_clk",
+		"gcc_q6_ahb_s_clk",
+		"gcc_wcss_axi_s_clk";
+
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+
+	qcom,rproc = <&q6v5_wcss>;
+	qcom,bootargs_smem = <507>;
+	boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>,
+			<0x2 0x4 0x2 0x12 0x0 0x0>;
+	status = "ok";
+	q6_wcss_pd1: remoteproc_pd1@4ab000 {
+		compatible = "qcom,ipq5018-wcss-ahb-mpd";
+		reg = <0x4ab000 0x20>;
+		reg-names = "rmb";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+					<&wcss_smp2p_in 9 0>,
+					<&wcss_smp2p_in 12 0>,
+					<&wcss_smp2p_in 11 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		resets = <&gcc GCC_WCSSAON_RESET>,
+				<&gcc GCC_WCSS_BCR>,
+				<&gcc GCC_CE_BCR>;
+		reset-names = "wcss_aon_reset",
+				"wcss_reset",
+				"ce_reset";
+
+		clocks = <&gcc GCC_WCSS_AHB_S_CLK>,
+				<&gcc GCC_WCSS_ACMT_CLK>,
+				<&gcc GCC_WCSS_AXI_M_CLK>;
+		clock-names = "gcc_wcss_ahb_s_clk",
+					"gcc_wcss_acmt_clk",
+					"gcc_wcss_axi_m_clk";
+
+		qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
+
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+					<&wcss_smp2p_out 9>,
+					<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>;
+	#else
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>, <&q6_caldb_region>;
+	#endif
+
+	};
+
+	q6_wcss_pd2: remoteproc_pd2 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "qcn6122/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 16 0>,
+					<&wcss_smp2p_in 17 0>,
+					<&wcss_smp2p_in 20 0>,
+					<&wcss_smp2p_in 19 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 16>,
+					<&wcss_smp2p_out 17>,
+					<&wcss_smp2p_out 18>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>;
+	#else
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>, <&q6_qcn6122_caldb_1>;
+	#endif
+
+	};
+
+	q6_wcss_pd3: remoteproc_pd3 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 24 0>,
+					<&wcss_smp2p_in 25 0>,
+					<&wcss_smp2p_in 28 0>,
+					<&wcss_smp2p_in 27 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 24>,
+					<&wcss_smp2p_out 25>,
+					<&wcss_smp2p_out 26>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef	__IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>;
+	#else
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>, <&q6_qcn6122_caldb_2>;
+	#endif
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x24>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4D400000 0x4D400000 0 0 0>;
+	qcom,caldb-size = <0x200000>;
+	mem-region = <&q6_ipq5018_data>;
+#else
+	memory-region = <&q6_ipq5018_data>;
+#endif
+	status = "ok";
+};
+
+&wifi1 {
+	/* QCN6122 5G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
+	qcom,rproc = <&q6_wcss_pd2>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x50>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4D600000 0x4D600000 0x4D300000 0x0 0x0>;
+	qcom,caldb-addr = <0x4E800000 0x4E800000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data1>;
+#else
+	memory-region = <&q6_qcn6122_data1>;
+#endif
+	status = "disabled";
+};
+
+&wifi2 {
+	/* QCN6122 6G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
+	qcom,rproc = <&q6_wcss_pd3>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0xb0>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4ED00000 0x4ED00000 0x4E400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4FF00000 0x4FF00000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data2>;
+#else
+	memory-region = <&q6_qcn6122_data2>;
+#endif
+	status = "ok";
+};
+
+
+&usb3 {
+	status = "ok";
+	device-power-gpio = <&tlmm 24 1>;
+};
+
+&dwc_0 {
+	/delete-property/ #phy-cells;
+	/delete-property/ phys;
+	/delete-property/ phy-names;
+};
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	#status = "disabled";
+	#perst-gpio = <&tlmm 18 1>;
+	perst-gpio = <&tlmm 18 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x2 {
+	#status = "disabled";
+	#perst-gpio = <&tlmm 15 1>;
+	perst-gpio = <&tlmm 15 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x1_rp {
+        status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+        status = "disabled";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+
+	};
+};
+

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-indio-um-525axp.dts

@@ -0,0 +1,941 @@
+/dts-v1/;
+/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "ipq5018.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "Indio UM-525AXP";
+	compatible = "indio,um-525axp", "qcom,ipq5018-mp03.5-c1", "qcom,ipq5018";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+                //led-failsafe = &led_red;
+                //led-running = &led_green;
+                //led-upgrade = &led_green;
+                //led-gateway = &led_blue;
+                //led-factory = &led_blue;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+	#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+	#endif
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+	/*                   256 MB Profile
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |           8MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x40800000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          13MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D100000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D300000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4E400000  |          15MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4F300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4F400000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x4500000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x1400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xD00000>;
+		};
+
+		m3_dump: m3_dump@4D100000 {
+			no-map;
+			reg = <0x0 0x4D100000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E200000 {
+			no-map;
+			reg = <0x0 0x4E200000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E300000 {
+			no-map;
+			reg = <0x0 0x4E300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E400000 {
+			no-map;
+			reg = <0x0 0x4E400000 0x0 0xF00000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4F300000 {
+			no-map;
+			reg = <0x0 0x4F300000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F400000 {
+			no-map;
+			reg = <0x0 0x4F400000 0x0 0x100000>;
+		};
+		
+	#else
+	/*                 512MB/1GB Profiles
+	 * +==========+==============+=========================+
+	 * |          |              |                         |
+	 * |  Region  | Start Offset |          Size           |
+	 * |          |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |    NSS   |  0x40000000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   Linux  |  0x41000000  | Depends on total memory |
+	 * +----------+--------------+-------------------------+
+	 * |   uboot  |  0x4A600000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    SBL   |  0x4AA00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |   smem   |  0x4AB00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    TZ    |  0x4AC00000  |           4MB           |
+	 * +----------+--------------+-------------------------+
+	 * |    Q6    |              |                         |
+	 * |   code/  |  0x4B000000  |          20MB           |
+	 * |   data   |              |                         |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   data   |  0x4C400000  |          14MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  M3 Dump |  0x4D200000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |   QDSS   |  0x4D300000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * |  IPQ5018 |              |                         |
+	 * |  Caldb   |  0x4D400000  |           2MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   data   |  0x4D600000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  M3 Dump |  0x4E600000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |   QDSS   |  0x4E700000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_1|              |                         |
+	 * |  Caldb   |  0x4E800000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   data   |  0x4ED00000  |          16MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  M3 Dump |  0x4FD00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |   QDSS   |  0x4FE00000  |           1MB           |
+	 * +----------+--------------+-------------------------+
+	 * | QCN6122_2|              |                         |
+	 * |  Caldb   |  0x4FF00000  |           5MB           |
+	 * +----------+--------------+-------------------------+
+	 * |                                                   |
+	 * |            Rest of the memory for Linux           |
+	 * |                                                   |
+	 * +===================================================+
+	 */
+		q6_mem_regions: q6_mem_regions@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 0x5400000>;
+		};
+
+		q6_code_data: q6_code_data@4B000000 {
+			no-map;
+			reg = <0x0 0x4B000000 0x0 01400000>;
+		};
+
+		q6_ipq5018_data: q6_ipq5018_data@4C400000 {
+			no-map;
+			reg = <0x0 0x4C400000 0x0 0xE00000>;
+		};
+
+		m3_dump: m3_dump@4D200000 {
+			no-map;
+			reg = <0x0 0x4D200000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D300000 {
+			no-map;
+			reg = <0x0 0x4D300000 0x0 0x100000>;
+		};
+
+		q6_caldb_region: q6_caldb_region@4D400000 {
+			no-map;
+			reg = <0x0 0x4D400000 0x0 0x200000>;
+		};
+
+		q6_qcn6122_data1: q6_qcn6122_data1@4D600000 {
+			no-map;
+			reg = <0x0 0x4D600000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E600000 {
+			no-map;
+			reg = <0x0 0x4E600000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E700000 {
+			no-map;
+			reg = <0x0 0x4E700000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_1: q6_qcn6122_caldb_1@4E800000 {
+			no-map;
+			reg = <0x0 0x4E800000 0x0 0x500000>;
+		};
+
+		q6_qcn6122_data2: q6_qcn6122_data2@4E900000 {
+			no-map;
+			reg = <0x0 0x4ED00000 0x0 0x1000000>;
+		};
+
+		m3_dump_qcn6122_2: m3_dump_qcn6122_2@4FD00000 {
+			no-map;
+			reg = <0x0 0x4FD00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_etr_2: q6_qcn6122_etr_2@4FE00000 {
+			no-map;
+			reg = <0x0 0x4FE00000 0x0 0x100000>;
+		};
+
+		q6_qcn6122_caldb_2: q6_qcn6122_caldb_2@4FF00000 {
+			no-map;
+			reg = <0x0 0x4FF00000 0x0 0x500000>;
+		};
+
+	#endif
+	};
+
+	soc {
+		gpio-watchdog {
+			compatible = "linux,wdt-gpio";
+			gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
+			hw_algo = "toggle";
+			hw_margin_ms = <5000>;
+			always-running;
+		};
+
+		serial@78af000 {
+			status = "ok";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			pinctrl-0 = <&blsp1_uart_pins>;
+			pinctrl-names = "default";
+		};
+
+		qpic_bam: dma@7984000{
+			status = "ok";
+		};
+
+		nand: qpic-nand@79b0000 {
+			pinctrl-0 = <&qspi_nand_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+		};
+
+		spi_0: spi@78b5000 { /* BLSP1 QUP0 */
+			pinctrl-0 = <&blsp0_spi_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+			status = "ok";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "n25q128a11";
+				linux,modalias = "m25p80", "n25q128a11";
+				spi-max-frequency = <50000000>;
+				use-default-sizes;
+			};
+		};
+
+		mdio0: mdio@88000 {
+			status = "ok";
+
+			ethernet-phy@0 {
+				reg = <7>;
+			};
+		};
+
+		mdio1: mdio@90000 {
+			status = "ok";
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 39 0>;
+
+			ethernet-phy@0 {
+				reg = <28>;
+			};
+		};
+
+		ess-instance {
+			num_devices = <0x1>;
+			ess-switch@0x39c00000 {
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/
+				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <7>;
+						mdiobus = <&mdio0>;
+					};
+					port@1 {
+						port_id = <2>;
+						phy_address = <0x1c>;
+						mdiobus = <&mdio1>;
+						port_mac_sel = "QGMAC_PORT";
+					};
+				};
+				led_source@0 {
+					source = <0>;
+					mode = "normal";
+					speed = "all";
+					blink_en = "enable";
+					active = "high";
+				};
+			};
+				ess-switch1@1 {
+				compatible = "qcom,ess-switch-qca83xx";
+				device_id = <1>;
+				switch_access_mode = "mdio";
+				mdio-bus = <&mdio1>;
+				reset_gpio = <0x28>;
+				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x1e>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				qca,ar8327-initvals = <
+						0x00004 0x7600000   /* PAD0_MODE */
+						0x00008 0x1000000   /* PAD5_MODE */
+						0x0000c 0x80        /* PAD6_MODE */
+						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
+						0x000e4 0xaa545     /* MAC_POWER_SEL */
+						0x000e0 0xc74164de  /* SGMII_CTRL */
+						0x0007c 0x4e        /* PORT0_STATUS */
+						0x00094 0x4e        /* PORT6_STATUS */
+				>;
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <1>;
+						phy_address = <28>;
+					};
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <1>;
+			reg = <0x39C00000 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <7>;
+			mdio-bus = <&mdio0>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		dp2 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
+			clock-names = "nss-snoc-gmac-axi-clk";
+			qcom,id = <2>;
+			reg = <0x39D00000 0x10000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,mactype = <2>;
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <28>;
+			mdio-bus = <&mdio1>;
+			local-mac-address = [000000000000];
+			phy-mode = "sgmii";
+		};
+
+		qcom,test@0 {
+			status = "ok";
+		};
+
+		nss-macsec1 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <0x1c>;
+			mdiobus = <&mdio1>;
+		};
+
+		lpass: lpass@0xA000000{
+			status = "disabled";
+		};
+
+		pcm: pcm@0xA3C0000{
+			pinctrl-0 = <&audio_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		pcm_lb: pcm_lb@0 {
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		status = "ok";
+	};
+
+};
+
+&tlmm {
+	pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>;
+	pinctrl-names = "default";
+
+	blsp0_uart_pins: uart_pins {
+		blsp0_uart_rx_tx {
+			pins = "gpio20", "gpio21";
+			function = "blsp0_uart0";
+			bias-disable;
+		};
+	};
+
+	blsp1_uart_pins: blsp1_uart_pins {
+		blsp1_uart_rx_tx {
+			pins = "gpio22", "gpio24", "gpio23", "gpio25";
+			function = "blsp1_uart2";
+			bias-disable;
+		};
+	};
+
+	blsp0_spi_pins: blsp0_spi_pins {
+		mux {
+			pins = "gpio10", "gpio11", "gpio12", "gpio13";
+			function = "blsp0_spi";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	qspi_nand_pins: qspi_nand_pins {
+		qspi_clock {
+			pins = "gpio9";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_cs {
+			pins = "gpio8";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_0 {
+			pins = "gpio7";
+			function = "qspi0";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_1 {
+			pins = "gpio6";
+			function = "qspi1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_2 {
+			pins = "gpio5";
+			function = "qspi2";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		qspi_data_3 {
+			pins = "gpio4";
+			function = "qspi3";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio36";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mux_1 {
+			pins = "gpio37";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	phy_led_pins: phy_led_pins {
+		gephy_led_pin {
+			pins = "gpio46";
+			function = "led0";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	i2c_pins: i2c_pins {
+		i2c_scl {
+			pins = "gpio25";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		i2c_sda {
+			pins = "gpio26";
+			function = "blsp2_i2c1";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	button_pins: button_pins {
+		reset_button {
+			pins = "gpio38";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+audio_pins: audio_pinmux {
+};
+        leds_pins: leds_pins {
+                led_5g {
+                        pins = "gpio34";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_2g {
+                        pins = "gpio33";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+                led_sys {
+                        pins = "gpio26";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+		led_onekey {
+                        pins = "gpio28";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+        };
+};
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+        leds {
+                compatible = "gpio-leds";
+                pinctrl-0 = <&leds_pins>;
+                pinctrl-names = "default";
+
+                led_blue: led@34 {
+                        label = "led_5g";
+                        gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_5g";
+                        default-state = "off";
+                };
+                led_green: led@33 {
+                        label = "led_2g";
+                        gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_2g";
+                        default-state = "off";
+                };
+                led_red: led@26 {
+                        label = "led_sys";
+                        gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_sys";
+                        default-state = "off";
+                };
+		led@28 {
+                        label = "led_onekey";
+                        gpios = <&tlmm 28 GPIO_ACTIVE_LOW>;
+                        linux,default-trigger = "led_onekey";
+                        default-state = "off";
+                };
+        };
+};
+
+&q6v5_wcss {
+	compatible = "qcom,ipq5018-q6-mpd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	firmware = "IPQ5018/q6_fw.mdt";
+	reg = <0x0cd00000 0x4040>,
+		<0x1938000 0x8>,
+		<0x193d204 0x4>;
+	reg-names = "qdsp6",
+			"tcsr-msip",
+			"tcsr-q6";
+	resets = <&gcc GCC_WCSSAON_RESET>,
+			<&gcc GCC_WCSS_Q6_BCR>;
+
+	reset-names = "wcss_aon_reset",
+			"wcss_q6_reset";
+
+	clocks = <&gcc GCC_Q6_AXIS_CLK>,
+		<&gcc GCC_WCSS_ECAHB_CLK>,
+		<&gcc GCC_Q6_AXIM_CLK>,
+		<&gcc GCC_Q6_AXIM2_CLK>,
+		<&gcc GCC_Q6_AHB_CLK>,
+		<&gcc GCC_Q6_AHB_S_CLK>,
+		<&gcc GCC_WCSS_AXI_S_CLK>;
+	clock-names = "gcc_q6_axis_clk",
+		"gcc_wcss_ecahb_clk",
+		"gcc_q6_axim_clk",
+		"gcc_q6_axim2_clk",
+		"gcc_q6_ahb_clk",
+		"gcc_q6_ahb_s_clk",
+		"gcc_wcss_axi_s_clk";
+
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>;
+	#else
+		memory-region = <&q6_mem_regions>, <&q6_etr_region>,
+				<&q6_caldb_region>;
+	#endif
+
+	qcom,rproc = <&q6v5_wcss>;
+	qcom,bootargs_smem = <507>;
+	boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>,
+			<0x2 0x4 0x2 0x12 0x0 0x0>;
+	status = "ok";
+	q6_wcss_pd1: remoteproc_pd1@4ab000 {
+		compatible = "qcom,ipq5018-wcss-ahb-mpd";
+		reg = <0x4ab000 0x20>;
+		reg-names = "rmb";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "IPQ5018/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 8 0>,
+					<&wcss_smp2p_in 9 0>,
+					<&wcss_smp2p_in 12 0>,
+					<&wcss_smp2p_in 11 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		resets = <&gcc GCC_WCSSAON_RESET>,
+				<&gcc GCC_WCSS_BCR>,
+				<&gcc GCC_CE_BCR>;
+		reset-names = "wcss_aon_reset",
+				"wcss_reset",
+				"ce_reset";
+
+		clocks = <&gcc GCC_WCSS_AHB_S_CLK>,
+				<&gcc GCC_WCSS_ACMT_CLK>,
+				<&gcc GCC_WCSS_AXI_M_CLK>;
+		clock-names = "gcc_wcss_ahb_s_clk",
+					"gcc_wcss_acmt_clk",
+					"gcc_wcss_axi_m_clk";
+
+		qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
+
+		qcom,smem-states = <&wcss_smp2p_out 8>,
+					<&wcss_smp2p_out 9>,
+					<&wcss_smp2p_out 10>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>;
+	#else
+		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
+				<&q6_etr_region>, <&q6_caldb_region>;
+	#endif
+
+	};
+
+	q6_wcss_pd2: remoteproc_pd2 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		m3_firmware = "qcn6122/m3_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 16 0>,
+					<&wcss_smp2p_in 17 0>,
+					<&wcss_smp2p_in 20 0>,
+					<&wcss_smp2p_in 19 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 16>,
+					<&wcss_smp2p_out 17>,
+					<&wcss_smp2p_out 18>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef __IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>;
+	#else
+		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
+				<&q6_qcn6122_etr_1>, <&q6_qcn6122_caldb_1>;
+	#endif
+
+	};
+
+	q6_wcss_pd3: remoteproc_pd3 {
+		compatible = "qcom,ipq5018-wcss-pcie-mpd";
+		firmware = "IPQ5018/q6_fw.mdt";
+		interrupts-extended = <&wcss_smp2p_in 24 0>,
+					<&wcss_smp2p_in 25 0>,
+					<&wcss_smp2p_in 28 0>,
+					<&wcss_smp2p_in 27 0>;
+		interrupt-names = "fatal",
+					"ready",
+					"spawn-ack",
+					"stop-ack";
+
+		qcom,smem-states = <&wcss_smp2p_out 24>,
+					<&wcss_smp2p_out 25>,
+					<&wcss_smp2p_out 26>;
+		qcom,smem-state-names = "shutdown",
+					"stop",
+					"spawn";
+	#ifdef	__IPQ_MEM_PROFILE_256_MB__
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>;
+	#else
+		memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>,
+				<&q6_qcn6122_etr_2>, <&q6_qcn6122_caldb_2>;
+	#endif
+	};
+};
+
+&i2c_0 {
+	pinctrl-0 = <&i2c_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&wifi0 {
+	/* IPQ5018 */
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x24>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4C400000 0x4C400000 0x4C400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4D400000 0x4D400000 0 0 0>;
+	qcom,caldb-size = <0x200000>;
+	mem-region = <&q6_ipq5018_data>;
+#else
+	memory-region = <&q6_ipq5018_data>;
+#endif
+	status = "ok";
+};
+
+&wifi1 {
+	/* QCN6122 5G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
+	qcom,rproc = <&q6_wcss_pd2>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0x50>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4D600000 0x4D600000 0x4D300000 0x0 0x0>;
+	qcom,caldb-addr = <0x4E800000 0x4E800000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data1>;
+#else
+	memory-region = <&q6_qcn6122_data1>;
+#endif
+	status = "disabled";
+};
+
+&wifi2 {
+	/* QCN6122 6G */
+	qcom,multipd_arch;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
+	qcom,rproc = <&q6_wcss_pd3>;
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+	qcom,tgt-mem-mode = <2>;
+#else
+	qcom,tgt-mem-mode = <1>;
+#endif
+	qcom,board_id = <0xb0>;
+#ifdef __CNSS2__
+	qcom,bdf-addr = <0x4ED00000 0x4ED00000 0x4E400000 0x0 0x0>;
+	qcom,caldb-addr = <0x4FF00000 0x4FF00000 0 0 0>;
+	qcom,caldb-size = <0x500000>;
+	mem-region = <&q6_qcn6122_data2>;
+#else
+	memory-region = <&q6_qcn6122_data2>;
+#endif
+	status = "ok";
+};
+
+
+&usb3 {
+	status = "ok";
+	device-power-gpio = <&tlmm 24 1>;
+};
+
+&dwc_0 {
+	/delete-property/ #phy-cells;
+	/delete-property/ phys;
+	/delete-property/ phy-names;
+};
+&hs_m31phy_0 {
+	status = "ok";
+};
+
+&eud {
+	status = "ok";
+};
+
+&pcie_x1 {
+	#status = "disabled";
+	#perst-gpio = <&tlmm 18 1>;
+	perst-gpio = <&tlmm 18 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x2 {
+	#status = "disabled";
+	#perst-gpio = <&tlmm 15 1>;
+	perst-gpio = <&tlmm 15 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_x1_rp {
+        status = "disabled";
+
+	mhi_0: qcom,mhi@0 {
+		reg = <0 0 0 0 0 >;
+	};
+};
+
+&pcie_x2_rp {
+        status = "disabled";
+
+	mhi_1: qcom,mhi@1 {
+		reg = <0 0 0 0 0 >;
+
+	};
+};
+

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-rap630c-311g.dts

@@ -151,6 +151,14 @@
 			no-map;
 			reg = <0x0 0x4F000000 0x0 0x100000>;
 		};
+
+		ramoops: ramoops@4f100000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4f100000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#else
 	/*                 512MB/1GB Profiles
 	 * +==========+==============+=========================+
@@ -285,6 +293,13 @@
 			reg = <0x0 0x4F800000 0x0 0x500000>;
 		};
 
+		ramoops: ramoops@4fd00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4fd00000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#endif
 	};
 

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-rap630w-311g.dts

@@ -151,6 +151,14 @@
 			no-map;
 			reg = <0x0 0x4F000000 0x0 0x100000>;
 		};
+
+		ramoops: ramoops@4f100000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4f100000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#else
 	/*                 512MB/1GB Profiles
 	 * +==========+==============+=========================+
@@ -285,6 +293,13 @@
 			reg = <0x0 0x4F800000 0x0 0x500000>;
 		};
 
+		ramoops: ramoops@4fd00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4fd00000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#endif
 	};
 

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-rap630w-312g.dts

@@ -154,6 +154,14 @@
 			no-map;
 			reg = <0x0 0x4F000000 0x0 0x100000>;
 		};
+
+		ramoops: ramoops@4f100000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4f100000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#else
 	/*		 512MB/1GB Profiles
 	 * +==========+==============+=========================+
@@ -288,6 +296,13 @@
 			reg = <0x0 0x4F800000 0x0 0x500000>;
 		};
 
+		ramoops: ramoops@4fd00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x4fd00000 0x0 0x80000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
 	#endif
 	};
 

feeds/ipq807x_v5.4/ipq50xx/image/ipq50xx.mk

@@ -93,6 +93,24 @@ define Device/edgecore_eap104
 endef
 TARGET_DEVICES += edgecore_eap104
 
+define Device/indio_um-325ax-v2
+  DEVICE_TITLE := Indio UM-325ax-V2
+  DEVICE_DTS := qcom-ipq5018-indio-um-325ax-v2
+  SUPPORTED_DEVICES := indio,um-325ax-v2
+  DEVICE_PACKAGES := ath11k-wifi-indio-um-325ax-v2 ath11k-firmware-ipq50xx-spruce ath11k-firmware-qcn6122
+  DEVICE_DTS_CONFIG := config@mp03.5-c1
+endef
+TARGET_DEVICES += indio_um-325ax-v2
+
+define Device/indio_um-525axp
+  DEVICE_TITLE := Indio UM-525axp
+  DEVICE_DTS := qcom-ipq5018-indio-um-525axp
+  SUPPORTED_DEVICES := indio,um-525axp
+  DEVICE_PACKAGES := ath11k-wifi-indio-um-525axp ath11k-firmware-ipq50xx-spruce ath11k-firmware-qcn6122
+  DEVICE_DTS_CONFIG := config@mp03.5-c1
+endef
+TARGET_DEVICES += indio_um-525axp
+
 define Device/udaya_a6_id2
   DEVICE_TITLE := Udaya A6 - ID2
   DEVICE_DTS := qcom-ipq5018-udaya-a6-id2

feeds/ipq807x_v5.4/log-helper/Makefile

@@ -0,0 +1,34 @@
+include $(TOPDIR)/rules.mk
+
+PKG_NAME:=log-helper
+PKG_VERSION:=1.0
+PKG_RELEASE:=1
+
+PKG_BUILD_DIR:=$(BUILD_DIR)/$(PKG_NAME)-$(PKG_VERSION)
+
+include $(INCLUDE_DIR)/package.mk
+include $(INCLUDE_DIR)/cmake.mk
+
+define Package/log-helper
+  SECTION:=utils
+  CATEGORY:=Utilities
+  TITLE:=Log backup helper
+  DEPENDS:=+libuci +libubus +libubox
+endef
+
+define Package/log-helper/description
+  This service that backs up files on boot.
+endef
+
+define Package/log-helper/install
+	$(INSTALL_DIR) $(1)/etc/config
+	$(INSTALL_BIN) ./files/log-helper.uci $(1)/etc/config/log-helper
+
+	$(INSTALL_DIR) $(1)/etc/init.d
+	$(INSTALL_BIN) ./files/log-helper.init $(1)/etc/init.d/log-helper
+
+	$(INSTALL_DIR) $(1)/usr/sbin
+	$(INSTALL_BIN) $(PKG_BUILD_DIR)/log-helper $(1)/usr/sbin/
+endef
+
+$(eval $(call BuildPackage,log-helper))

feeds/ipq807x_v5.4/log-helper/files/log-helper.init

@@ -0,0 +1,30 @@
+#!/bin/sh /etc/rc.common
+
+USE_PROCD=1
+START=15
+
+PROG=/usr/sbin/log-helper
+
+#add directory that need to be preserved during OpenWRT sysupgrade
+check_upgrade_conf() {
+	dir="$1"
+
+	grep -q ${dir} /etc/sysupgrade.conf
+	[ $? -ne 0 ] && {
+		echo "/${dir}/" >> /etc/sysupgrade.conf
+	}
+}
+
+start_service() {
+	local enabled
+	config_load log-helper
+	config_get_bool enabled global enabled 0
+	[ ${enabled} -eq 0 ] && return 1
+
+	config_get backup_dir global backup_dir "backup_storage"
+	check_upgrade_conf ${backup_dir}
+
+	procd_open_instance
+	procd_set_param command $PROG
+	procd_close_instance
+}

feeds/ipq807x_v5.4/log-helper/files/log-helper.uci

@@ -0,0 +1,18 @@
+config log-helper 'global'
+	option enabled '1'
+
+	# Directory in overlay file system for backed up files.
+	option backup_dir 'backup_storage'
+
+	# Free space safety margin in KB.
+	# A backup will be skipped if available space of overlay is less than (file_size + threshold).
+	option space_threshold '2048'
+
+	# To specify the maximum number of rotations.
+	option max_rotations '3'
+
+	option backup_file 'backup.tgz'
+
+	list file_list '/sys/fs/pstore/dmesg-ramoops-0'
+	list file_list '/sys/fs/pstore/console-ramoops-0'
+	list file_list '/sys/fs/pstore/pmsg-ramoops-0'

feeds/ipq807x_v5.4/log-helper/src/CMakeLists.txt

@@ -0,0 +1,22 @@
+cmake_minimum_required(VERSION 2.6)
+
+INCLUDE(CheckFunctionExists)
+
+PROJECT(log-helper C)
+ADD_DEFINITIONS(-Os -Wall -Werror)
+ADD_DEFINITIONS(-std=gnu99 -g3 -Wmissing-declarations -Wno-unused-parameter)
+
+SET(CMAKE_SHARED_LIBRARY_LINK_C_FLAGS "")
+SET(SOURCES main.c)
+
+FIND_LIBRARY(uci NAMES uci)
+FIND_LIBRARY(ubus NAMES ubus)
+FIND_LIBRARY(ubox NAMES ubox)
+
+ADD_EXECUTABLE(log-helper ${SOURCES})
+
+TARGET_LINK_LIBRARIES(log-helper ${uci} ${ubus} ${ubox})
+
+INSTALL(TARGETS log-helper
+	RUNTIME DESTINATION sbin
+)

feeds/ipq807x_v5.4/log-helper/src/main.c

@@ -0,0 +1,341 @@
+/*
+ * Copyright (c) 2025, CyberTAN Technology Inc.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions, and the following disclaimer.
+ *
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions, and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ *
+ * 3. Neither the name of CyberTAN Technology Inc. nor the names of its
+ * contributors may be used to endorse or promote products derived from
+ * this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ */
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include <unistd.h>
+#include <syslog.h>
+#include <sys/stat.h>
+#include <sys/statvfs.h>
+#include <libgen.h>
+#include <limits.h>
+#include <errno.h>
+#include <stdbool.h>
+
+#include <uci.h>
+#include <libubus.h>
+
+#define DEFAULT_BACKUP_DIRECTOR  "backup_storage"
+#define DEFAULT_BACKUP_FILE_NAME "backup.tgz"
+#define DEFAULT_MAX_ROTATIONS    3
+#define DEFAULT_SPACE_THRESH     2048
+#define UCI_CONFIG_FILE          "log-helper"
+#define OVERLAYFS_ROOT           "/overlay/upper"
+
+
+
+static int rotate_logs(const char *base_log_path, int max_rotations);
+static int move_file(const char *src_path, const char *dest_dir);
+static void do_backup(void);
+
+static char backup_dir[1024];
+
+
+
+/**
+ * @brief Performs log rotation.
+ * @param base_log_path The path of the base log file, e.g., "app.log".
+ * @param max_rotations The maximum number of backup files to keep.
+ * @return 0 on success, -1 on failure.
+ */
+static int rotate_logs(const char *base_log_path, int max_rotations) {
+	struct stat info;
+	char log_name[NAME_MAX] = {0};
+	char log_path[1024] = {0};
+	char src_path[PATH_MAX] = {0};
+	char dest_path[PATH_MAX] ={0};
+	int len;
+
+	if (!strlen(backup_dir) || stat(backup_dir, &info) != 0) {
+		syslog(LOG_ERR, "Wrong backup directory: %s", backup_dir);
+		return -1;
+	}
+
+	if (max_rotations <= 1) {
+		syslog(LOG_ERR, "max_rotations must be greater than 1: %d", max_rotations);
+		return -1;
+	}
+
+	strncpy(log_name, basename((char *)base_log_path), sizeof(log_name));
+	len = snprintf(log_path, sizeof(log_path), "%s/%s", backup_dir, log_name);
+	if (len >= sizeof(log_path)) {
+		syslog(LOG_ERR, "Buffer too small, path was truncated.");
+		return -1;
+	}
+
+	if (access(log_path, F_OK) != 0) {
+		syslog(LOG_DEBUG, "File not found: %s", log_path);
+		return 0;
+	}
+
+	// Remove the oldest backup file (e.g., app.log.5).
+	snprintf(dest_path, sizeof(dest_path), "%s.%d", log_path, max_rotations);
+	if (remove(dest_path) == 0) {
+		syslog(LOG_DEBUG, "Deleted oldest backup: %s", dest_path);
+	}
+
+	// Rename files in reverse order, from the second to last backup.
+	for (int i = max_rotations - 1; i >= 0; --i) {
+		// Generate the source file path.
+		if (i) {
+			// the source is the .i backup file.
+			snprintf(src_path, sizeof(src_path) - 2, "%s.%d", log_path, i);
+		} else {
+			// the source is the original log file.
+			src_path[strlen(log_path)] = '\0'; // Ensure null-termination.
+		}
+
+		// Generate the destination file path (i+1).
+		snprintf(dest_path, sizeof(dest_path), "%s.%d", log_path, i + 1);
+
+		// Check if the source file exists before trying to rename it.
+		if (access(src_path, F_OK) == 0) {
+			if (!rename(src_path, dest_path)) {
+				syslog(LOG_DEBUG, "rename '%s' to '%s'.", src_path, dest_path);
+			} else {
+				syslog(LOG_ERR, "Could not rename '%s' to '%s'.", src_path, dest_path);
+				return -1;
+			}
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * @brief Moves a file from a source path to a destination directory.
+ * * @param src_path Absolute path to the source file.
+ * @param dest_dir Absolute path to the destination directory.
+ * @return 0 on success, -1 on failure.
+ */
+static int move_file(const char *src_path, const char *dest_dir) {
+	size_t len;
+	FILE *fd_s, *fd_d;
+	char buffer[4096] = {0};
+	char dest_path[PATH_MAX] = {0};
+
+	snprintf(dest_path, sizeof(dest_path) - 1, "%s/%s", dest_dir, basename((char *)src_path));
+
+	fd_s = fopen(src_path, "rb");
+	if (!fd_s) {
+		syslog(LOG_ERR, "Failed to open source file %s: %s", src_path, strerror(errno));
+		return -1;
+	}
+
+	fd_d = fopen(dest_path, "wb+");
+	if (!fd_d) {
+		syslog(LOG_ERR, "Failed to open destination file %s: %s", dest_path, strerror(errno));
+		fclose(fd_s);
+		return -1;
+	}
+
+	while ((len = fread(buffer, 1, sizeof(buffer), fd_s)) > 0) {
+		if (fwrite(buffer, 1, len, fd_d) != len) {
+			syslog(LOG_ERR, "Error writing to destination file: %s", dest_path);
+			fclose(fd_s);
+			fclose(fd_d);
+			return -1;
+		}
+	}
+
+	unlink(src_path);
+
+	fclose(fd_s);
+	fclose(fd_d);
+
+	return 0;
+}
+
+static int build_file_list(char *file_list, size_t list_size, const char *path) {
+	size_t current_len = strlen(file_list);
+	size_t path_len = strlen(path);
+	struct stat st;
+
+	if (stat(path, &st) != 0) {
+		syslog(LOG_WARNING, "Backup source file not found: %s", path);
+		return 0;
+	}
+
+	if (current_len + path_len + 1 > list_size - 1) {
+		syslog(LOG_ERR, "Buffer too small.");
+		return -1;
+	}
+
+	if (strlen(file_list)) {
+		strcat(file_list, " ");
+	}
+	strcat(file_list, path);
+
+	return 0;
+}
+
+/**
+ * @brief Performs the backup task based on UCI configuration.
+ */
+static void do_backup(void) {
+	struct uci_context *ctx = uci_alloc_context();
+	struct uci_package *pkg = NULL;
+	struct uci_section *s = NULL;
+	struct uci_element *e = NULL;
+	struct uci_option *o = NULL;
+	struct statvfs vfs;
+	struct stat st;
+	long space_threshold_kb;
+	long available_kb;
+	long max_rotations;
+	long file_kb;
+	const char *str = NULL;
+	char file_list[1024] = {0};
+	char cmd[1024] = {0};
+	char backup_file[256] = {0};
+	char tmp_file[256] = {0};
+	int n, ret;
+
+	if (uci_load(ctx, UCI_CONFIG_FILE, &pkg) != UCI_OK) {
+		syslog(LOG_ERR, "Failed to load UCI config: %s", UCI_CONFIG_FILE);
+		return;
+	}
+
+	s = uci_lookup_section(ctx, pkg, "global");
+	if (!s) {
+		syslog(LOG_ERR, "UCI section 'global' not found in %s", UCI_CONFIG_FILE);
+		goto backup_exit;
+	}
+
+	// Iterate through the list of files to be backed up
+	uci_foreach_element(&s->options, e) {
+		struct uci_element *le;
+		o = uci_to_option(e);
+		if (o->type != UCI_TYPE_LIST || strcmp(o->e.name, "file_list") != 0)
+			continue;
+
+		list_for_each_entry(le, &o->v.list, list) {
+			const char *f = le->name;
+
+			if (build_file_list(file_list, sizeof(file_list), f) != 0) {
+				goto backup_exit;
+			}
+		}
+	}
+
+	if (!strlen(file_list)) {
+		goto backup_exit;
+	}
+
+	// Get the backup directory
+	str = uci_lookup_option_string(ctx, s, "backup_dir");
+	if (!str || strlen(str)==0)
+		str = DEFAULT_BACKUP_DIRECTOR;
+
+	snprintf(backup_dir, sizeof(backup_dir) - 1 , "/%s", str);
+	mkdir(backup_dir, 0755);
+
+	// Get the backup file name
+	str = uci_lookup_option_string(ctx, s, "backup_file");
+	if (!str || strlen(str)==0)
+		str = DEFAULT_BACKUP_FILE_NAME;
+
+	n = snprintf(backup_file, sizeof(backup_file) - 1, "%s/%s", backup_dir, str);
+	if (n >= sizeof(backup_file)) {
+		syslog(LOG_ERR, "File buffer is too small.\n");
+		goto backup_exit;
+	}
+	n = snprintf(tmp_file, sizeof(tmp_file) - 1, "/tmp/%s", str);
+	if (n >= sizeof(tmp_file)) {
+		syslog(LOG_ERR, "Tmp buffer is too small.\n");
+		goto backup_exit;
+	}
+
+	// Create the backup tgz file in /tmp/
+	n = snprintf(cmd, sizeof(cmd) - 1, "tar -czf %s %s", tmp_file, file_list);
+	if (n >= sizeof(cmd)) {
+		syslog(LOG_ERR, "Command buffer is too small.\n");
+		goto backup_exit;
+	}
+
+	ret = system(cmd);
+	if (ret){
+		syslog(LOG_ERR, "The tar command failed with return code: %d\n", ret);
+		goto backup_exit;
+	}
+
+	// Get available space on the overlay filesystem
+	if (statvfs(OVERLAYFS_ROOT, &vfs) != 0) {
+		syslog(LOG_ERR, "Failed to get overlay filesystem stats: %s", strerror(errno));
+		goto backup_exit;
+	}
+	available_kb = (vfs.f_bavail * vfs.f_bsize) / 1024;
+	str = uci_lookup_option_string(ctx, s, "space_threshold");
+	space_threshold_kb = str ? atol(str) : DEFAULT_SPACE_THRESH;
+	syslog(LOG_INFO, "Overlay available space: %ldKB", available_kb);
+
+	// Check if there is enough space
+	stat(tmp_file, &st);
+	file_kb = st.st_size / 1024;
+	if (available_kb < (file_kb + space_threshold_kb)) {
+		syslog(LOG_ERR, "Overlay space insufficient for %s. (Available: %ldKB, Required: %ldKB)",
+				tmp_file, available_kb, (file_kb + space_threshold_kb));
+		goto backup_exit;
+	}
+
+	// Get the maximum number of rotations
+	str = uci_lookup_option_string(ctx, s, "max_rotations");
+	max_rotations = str ? atol(str) : DEFAULT_MAX_ROTATIONS;
+
+	if (max_rotations > 1 && access(backup_file, F_OK)==0) {
+		rotate_logs(backup_file, max_rotations);
+	}
+
+	if (move_file(tmp_file, backup_dir) == 0) {
+		syslog(LOG_INFO, "Successfully backed up to '%s'.", backup_file);
+	} else {
+		syslog(LOG_ERR, "Failed to move '%s' to '%s': %s", tmp_file, backup_file, strerror(errno));
+	}
+
+backup_exit:
+	uci_free_context(ctx);
+}
+
+
+
+/**
+ * @brief Main entry point of the application.
+ */
+int main(int argc, char **argv) {
+	// Set up syslog with the program name
+	openlog("log-helper", LOG_PID, LOG_DAEMON);
+
+	do_backup();
+
+	closelog();
+
+	return 0;
+}

feeds/mediatek-sdk/log-helper

@@ -0,0 +1 @@
+../../feeds/ipq807x_v5.4/log-helper

feeds/qca-wifi-7/ath12k-wifi/Makefile

@@ -93,6 +93,11 @@ $(call Package/ath12k-wifi-default)
     TITLE:=board-2.bin for NWA130BE
 endef
 
+define Package/ath12k-wifi-zyxel-nwa50be
+$(call Package/ath12k-wifi-default)
+    TITLE:=board-2.bin for NWA50BE
+endef
+
 define Package/ath12k-wifi-cig-wf672
 $(call Package/ath12k-wifi-default)
     TITLE:=board-2.bin for WF672
@@ -191,6 +196,14 @@ define Package/ath12k-wifi-zyxel-nwa130be/install
 	$(INSTALL_DATA) ./board-2.bin.nwa130be.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
 endef
 
+define Package/ath12k-wifi-zyxel-nwa50be/install
+	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN6432/hw1.0/
+	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
+	$(INSTALL_DATA) ./board-2.bin.nwa50be.QCN6432 $(1)/lib/firmware/ath12k/QCN6432/hw1.0/board-2.bin
+	$(INSTALL_DATA) ./board-2.bin.nwa50be.IPQ5332 $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/board-2.bin
+	$(INSTALL_DATA) ./ipq5332_qcn6432.regdb $(1)/lib/firmware/ath12k/QCN6432/hw1.0/regdb.bin
+endef
+
 define Package/ath12k-wifi-cig-wf672/install
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/QCN92XX/hw1.0/
 	$(INSTALL_DIR) $(1)/lib/firmware/ath12k/IPQ5332/hw1.0/
@@ -210,4 +223,5 @@ $(eval $(call BuildPackage,ath12k-wifi-cig-wf189h))
 $(eval $(call BuildPackage,ath12k-wifi-sercomm-ap72tip))
 $(eval $(call BuildPackage,ath12k-wifi-sercomm-ap72tip-v4))
 $(eval $(call BuildPackage,ath12k-wifi-zyxel-nwa130be))
+$(eval $(call BuildPackage,ath12k-wifi-zyxel-nwa50be))
 $(eval $(call BuildPackage,ath12k-wifi-cig-wf672))

feeds/qca-wifi-7/ath12k-wifi/board-2-nwa50be-IPQ5332.json

@@ -0,0 +1,20 @@
+[
+    {
+        "board": [
+            {
+                "names": [
+                    "bus=ahb,qmi-chip-id=0,qmi-board-id=18"
+                ],
+                "data": "nwa50be-IPQ5332.bin"
+            }
+        ],
+        "regdb": [
+            {
+                "names": [
+                    "bus=ahb,qmi-chip-id=0,qmi-board-id=18"
+                ],
+                "data": "ipq5332.regdb"
+            }
+        ]
+    }
+]

feeds/qca-wifi-7/ath12k-wifi/board-2-nwa50be-QCN6432.json

@@ -0,0 +1,20 @@
+[
+    {
+        "board": [
+            {
+                "names": [
+                    "bus=ahb,qmi-chip-id=0,qmi-board-id=112"
+                ],
+                "data": "nwa50be-QCN6432.bin"
+            }
+        ],
+        "regdb": [
+            {
+                "names": [
+                    "bus=ahb,qmi-chip-id=0,qmi-board-id=112"
+                ],
+                "data": "ipq5332_qcn6432.regdb"
+            }
+        ]
+    }
+]

feeds/qca-wifi-7/ath12k-wifi/generate.sh

@@ -18,3 +18,6 @@ $encoder -c board-2-ap72tip-v4-QCN92XX.json -o board-2.bin.ap72tip-v4.QCN92XX
 
 $encoder -c board-2-nwa130be-IPQ5332.json -o board-2.bin.nwa130be.IPQ5332
 $encoder -c board-2-nwa130be-QCN92XX.json -o board-2.bin.nwa130be.QCN92XX
+
+$encoder -c board-2-nwa50be-IPQ5332.json -o board-2.bin.nwa50be.IPQ5332
+$encoder -c board-2-nwa50be-QCN6432.json -o board-2.bin.nwa50be.QCN6432

feeds/qca-wifi-7/cig-platform-pkg/cig-wifi-mode-sw/Makefile

@@ -24,7 +24,9 @@ endef
 
 define KernelPackage/cig-wifi-mode-sw/install
 	$(INSTALL_DIR) $(1)/usr/sbin/
+	$(INSTALL_DIR) $(1)/etc/init.d/
 	$(INSTALL_BIN) ./files/cig_wifi_mode_sw $(1)/usr/sbin/cig_wms
+	$(INSTALL_BIN) ./files/cig_wifi_mode_boot $(1)/etc/init.d/cig_wmb
 endef
 
 $(eval $(call KernelPackage,cig-wifi-mode-sw))

feeds/qca-wifi-7/cig-platform-pkg/cig-wifi-mode-sw/files/cig_wifi_mode_boot

@@ -0,0 +1,13 @@
+#!/bin/sh /etc/rc.common
+
+START=60
+
+boot(){
+	local bands=$(cat /proc/rf_switch)
+
+	if [ "x$bands" = "x3" ]; then
+		echo "AFC is not ready, switch to 2-band mode" >/dev/console
+		echo 2 > /proc/rf_switch
+		firstboot -y -r
+	fi
+}

feeds/qca-wifi-7/hostapd/files/common.uc

@@ -259,8 +259,13 @@ const phy_proto = {
 			addr[0] ^= idx << 2;
 			break;
 		case "b5":
-			if (mbssid)
+			if (mbssid) {
+				let b5 = addr[5];
+				addr[5] = addr[3];
+				addr[3] = b5;
+				addr[5] &= ~0xf;
 				addr[0] |= 2;
+			}
 			addr[5] ^= idx;
 			break;
 		default:

feeds/qca-wifi-7/ipq53xx/base-files/etc/board.d/02_network

@@ -20,7 +20,8 @@ ipq53xx_setup_interfaces()
 		;;
 	sonicfi,rap7110c-341x|\
 	sonicfi,rap750e-h|\
-	sonicfi,rap750e-s)
+	sonicfi,rap750e-s|\
+	zyxel,nwa50be)
 		ucidef_set_interfaces_lan_wan "" "eth0"
 		;;
 	cig,wf189w)
@@ -127,6 +128,16 @@ qcom_setup_macs()
 		ucidef_set_wireless_macaddr_base 5g $(macaddr_add "$wan_mac" 3)
 		ucidef_set_wireless_macaddr_base 6g $(macaddr_add "$wan_mac" 4)
 		;;
+	zyxel,nwa50be)
+		wan_mac=$(cat /proc/cmdline)
+		wan_mac="${wan_mac##*hwaddr=}"
+		wan_mac="${wan_mac%% *}"
+		wan_mac="$(echo ${wan_mac} | sed 's/\(..\)/\1:/g;s/:$//')"
+		ucidef_set_network_device_mac eth0 $wan_mac
+		ucidef_set_label_macaddr $wan_mac
+		ucidef_set_wireless_macaddr_base 2g $(macaddr_add "$wan_mac" 1)
+		ucidef_set_wireless_macaddr_base 5g $(macaddr_add "$wan_mac" 2)
+		;;
         *)
                 wan_mac=$(cat /sys/class/net/eth1/address)
                 lan_mac=$(macaddr_add "$wan_mac" 1)

feeds/qca-wifi-7/ipq53xx/base-files/etc/hotplug.d/firmware/10-ath12k-caldata

@@ -67,8 +67,9 @@ ath12k/IPQ5332/hw1.0/caldata.bin)
 	emplus,wap7635|\
 	sercomm,ap72tip-v4|\
 	sercomm,ap72tip|\
-	zyxel,nwa130be)
-		caldata_extract "0:ART" 0x1000 0x20000 
+	zyxel,nwa130be|\
+	zyxel,nwa50be)
+		caldata_extract "0:ART" 0x1000 0x20000
 		;;
 	cig,wf672)
 		cig_ipq5322_cal
@@ -124,6 +125,9 @@ ath12k/QCN6432/hw1.0/cal-ahb-soc@0:wifi2@c0000000.bin)
 	cig,wf189w)
 		caldata_extract "0:ART" 0x58800 0x20000
 		;;
+	zyxel,nwa50be)
+		caldata_extract "0:ART" 0x58800 0x2d000
+		;;
 	esac
 	;;
 ath12k/IPQ5332/hw1.0/board-2.bin)

feeds/qca-wifi-7/ipq53xx/base-files/etc/init.d/phy_quirks

@@ -9,14 +9,5 @@ boot() {
 	edgecore,eap105)
 		ssdk_sh debug phy set 0x1 0x601FD032 0xff
 		;;
-	zyxel,nwa130be)
-		#eth0: APPE: phyaddr 4  green:2.5G  orange:others
-		ssdk_sh debug phy set 4 0x40078074 0x670
-		ssdk_sh debug phy set 4 0x40078078 0x8600
-
-		#eth1:  MHT: phyaddr 3  green:2.5G orange:others
-		ssdk_sh debug phy set 3 0x40078074 0x670
-		ssdk_sh debug phy set 3 0x40078078 0x8600
-		;;
 	esac
 }

feeds/qca-wifi-7/ipq53xx/base-files/lib/upgrade/platform.sh

@@ -174,7 +174,8 @@ platform_do_upgrade() {
 		sonicfi_dualimage_check
 		nand_upgrade_tar "$1"
 		;;
-	zyxel,nwa130be)
+	zyxel,nwa130be|\
+	zyxel,nwa50be)
 		nand_upgrade_tar "$1"
 		;;
 	esac

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-zyxel-nwa130be.dts

@@ -18,6 +18,21 @@
 	model = "Zyxel NWA130BE";
 	compatible = "zyxel,nwa130be", "qcom,ipq5332-ap-mi01.6", "qcom,ipq5332-rdp468", "qcom,ipq5332";
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			no-map;
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+	};
+
 	aliases {
 		serial0 = &blsp1_uart0;
 		serial1 = &blsp1_uart1;
@@ -128,6 +143,26 @@
 					blink_en = "enable";
 					active = "high";
 				};
+
+				qcom,port_ledinfo {
+					port@1 {
+						port = <2>;
+						led_source@0 {
+							source = <0>;
+							mode = "normal";
+							speed = "2500M";
+							active = "high";
+							blink_en = "enable";
+						};
+						led_source@1 {
+							source = <1>;
+							mode = "normal";
+							speed = "10M", "100M","1000M";
+							active = "high";
+							blink_en = "enable";
+						};
+					};
+				};
 			};
 
 			ess-switch1@1 {
@@ -164,6 +199,26 @@
 					};
 				};
 
+				qcom,port_ledinfo {
+					port@3 {
+						port = <3>;
+						led_source@0 {
+							source = <0>;
+							mode = "normal";
+							speed = "2500M";
+							active = "high";
+							blink_en = "enable";
+						};
+						led_source@1 {
+							source = <1>;
+							mode = "normal";
+							speed = "10M", "100M","1000M";
+							active = "high";
+							blink_en = "enable";
+						};
+					};
+				};
+
 				led_source@2 {
 					source = <2>;
 					mode = "normal";

feeds/qca-wifi-7/ipq53xx/dts/ipq5332-zyxel-nwa50be.dts

@@ -0,0 +1,956 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ5332 RDP442 board device tree source
+ *
+ * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022-2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq5332.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "ipq5332-default-memory.dtsi"
+
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ5332/RDP442/AP-MI01.3";
+	compatible = "zyxel,nwa50be", "qcom,ipq5332-ap-mi01.3", "qcom,ipq5332-rdp442", "qcom,ipq5332";
+
+#ifdef __IPQ_MEM_PROFILE_512_MB__
+
+	/*     512M  Layout for IPQ5332 + QCN6432 + QCN6432
+	 * +==========+==============+========================+
+	 * |         |              |                         |
+	 * |  Region | Start Offset |          Size           |
+	 * |         |              |                         |
+	 * +---------+--------------+-------------------------+
+	 * |   Q6    |              |                         |
+	 * |  code/  |  0x4A900000  |          25MB           |
+	 * |  data   |              |                         |
+	 * +---------+--------------+-------------------------+
+	 * | IPQ5332 |              |                         |
+	 * |  data   |  0x4C200000  |          17MB           |
+	 * +---------+--------------+-------------------------+
+	 * | IPQ5332 |              |                         |
+	 * | M3 Dump |  0x4D300000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * | IPQ5332 |              |                         |
+	 * |  QDSS   |  0x4D400000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * | IPQ5332 |              |                         |
+	 * |  CALDB  |  0x4D500000  |           3MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_1|              |                         |
+	 * |  data   |  0x4D800000  |          16MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_1|              |                         |
+	 * | M3 Dump |  0x4E800000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_1|              |                         |
+	 * |  QDSS   |  0x4E900000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_1|              |                         |
+	 * |  CALDB  |  0x4EA00000  |           5MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_2|              |                         |
+	 * |  data   |  0x4EF00000  |          16MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_2|              |                         |
+	 * | M3 Dump |  0x4FF00000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_2|              |                         |
+	 * |  QDSS   |  0x50000000  |           1MB           |
+	 * +---------+--------------+-------------------------+
+	 * |QCN6432_2|              |                         |
+	 * |  CALDB  |  0x50100000  |           5MB           |
+	 * +---------+--------------+-------------------------+
+	 * |         |              |                         |
+	 * |   MLO   |  0x50600000  |          12MB           |
+	 * +==================================================+
+	 * |                                                  |
+	 * |                                                  |
+	 * |                                                  |
+	 * |             Rest of memory for Linux             |
+	 * |                                                  |
+	 * |                                                  |
+	 * |                                                  |
+	 * +==================================================+
+	 */
+
+	reserved-memory {
+
+		/delete-node/ m3_dump@4cc00000;
+		/delete-node/ q6_etr_dump@1;
+		/delete-node/ mlo_global_mem_0@0x4db00000;
+		/delete-node/ wcnss@4a900000;
+		/delete-node/ q6_caldb_region@4ce00000;
+
+		q6_mem_regions: q6_mem_regions@4A900000  {
+			reg = <0x0 0x4a900000 0x0 0x5D00000>;
+			no-map;
+		};
+
+		q6_code_data: q6_code_data@4A900000 {
+			reg = <0x0 0x4a900000 0x0 0x1900000>;
+			no-map;
+		};
+
+		q6_ipq5332_data: q6_ipq5332_data@4C200000 {
+			reg = <0x0 0x4C200000 0x0 0x1100000>;
+			no-map;
+		};
+
+		m3_dump: m3_dump@4D300000 {
+			reg = <0x0 0x4D300000 0x0 0x100000>;
+			no-map;
+		};
+
+		q6_etr_region: q6_etr_dump@4D400000 {
+			reg = <0x0 0x4D400000 0x0 0x100000>;
+			no-map;
+		};
+
+		q6_ipq5332_caldb: q6_ipq5332_caldb@4D500000 {
+			reg = <0x0 0x4D500000 0x0 0x300000>;
+			no-map;
+		};
+
+		q6_qcn6432_data_1: q6_qcn6432_data_1@4D800000 {
+			reg = <0x0 0x4D800000 0x0 0x1000000>;
+			no-map;
+		};
+
+		m3_dump_qcn6432_1: m3_dump_qcn6432_1@4E800000 {
+			reg = <0x0 0x4E800000 0x0 0x100000>;
+			no-map;
+                };
+
+		q6_qcn6432_etr_1: q6_qcn6432_etr_1@4E900000 {
+			reg = <0x0 0x4E900000 0x0 0x100000>;
+			no-map;
+		};
+
+		q6_qcn6432_caldb_1: q6_qcn6432_caldb_1@4EA00000 {
+			reg = <0x0 0x4EA00000 0x0 0x500000>;
+			no-map;
+		};
+
+		q6_qcn6432_data_2: q6_qcn6432_data_2@4EF00000 {
+			reg = <0x0 0x4EF00000 0x0 0x1000000>;
+			no-map;
+		};
+
+		m3_dump_qcn6432_2: m3_dump_qcn6432_2@4FF00000 {
+			reg = <0x0 0x4FF00000 0x0 0x100000>;
+			no-map;
+                };
+
+		q6_qcn6432_etr_2: q6_qcn6432_etr_2@50000000 {
+			reg = <0x0 0x50000000 0x0 0x100000>;
+			no-map;
+		};
+
+		q6_qcn6432_caldb_2: q6_qcn6432_caldb_2@50100000 {
+			reg = <0x0 0x50100000 0x0 0x500000>;
+			no-map;
+		};
+
+		mlo_global_mem0: mlo_global_mem_0@50600000 {
+			reg = <0x0 0x50600000 0x0 0xC00000>;
+			no-map;
+		};
+	};
+#else
+
+	/*  1G  Layout for IPQ5332 + QCN6432 + QCN6432
+	* +==========+==============+========================+
+	* |         |              |                         |
+	* |  Region | Start Offset |          Size           |
+	* |         |              |                         |
+	* +---------+--------------+-------------------------+
+	* |   Q6    |              |                         |
+	* |  code/  |  0x4A900000  |          25MB           |
+	* |  data   |              |                         |
+	* +---------+--------------+-------------------------+
+	* | IPQ5332 |              |                         |
+	* |  data   |  0x4C200000  |          21MB           |
+	* +---------+--------------+-------------------------+
+	* | IPQ5332 |              |                         |
+	* | M3 Dump |  0x4D700000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* | IPQ5332 |              |                         |
+	* |  QDSS   |  0x4D800000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* | IPQ5332 |              |                         |
+	* |  CALDB  |  0x4D900000  |           5MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_1|              |                         |
+	* |  data   |  0x4DE00000  |          21MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_1|              |                         |
+	* | M3 Dump |  0x4F300000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_1|              |                         |
+	* |  QDSS   |  0x4F400000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_1|              |                         |
+	* |  CALDB  |  0x4F500000  |           5MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_2|              |                         |
+	* |  data   |  0x4FA00000  |          21MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_2|              |                         |
+	* | M3 Dump |  0x50F00000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_2|              |                         |
+	* |  QDSS   |  0x51000000  |           1MB           |
+	* +---------+--------------+-------------------------+
+	* |QCN6432_2|              |                         |
+	* |  CALDB  |  0x51100000  |           5MB           |
+	* +---------+--------------+-------------------------+
+	* |         |              |                         |
+	* |   MLO   |  0x51600000  |          12MB           |
+	* +==================================================+
+	* |                                                  |
+	* |                                                  |
+	* |                                                  |
+	* |             Rest of memory for Linux             |
+	* |                                                  |
+	* |                                                  |
+	* |                                                  |
+	* +==================================================+
+	*/
+	reserved-memory {
+
+		/delete-node/ m3_dump@4cc00000;
+		/delete-node/ q6_etr_dump@1;
+		/delete-node/ mlo_global_mem_0@0x4db00000;
+		/delete-node/ wcnss@4a900000;
+		/delete-node/ q6_caldb_region@4ce00000;
+
+		ramoops@49c00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x49c00000 0x0 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			pmsg-size = <0x20000>;
+		};
+
+		q6_mem_regions: q6_mem_regions@4A900000  {
+			no-map;
+			reg = <0x0 0x4a900000 0x0 0x6D00000>;
+		};
+
+		q6_code_data: q6_code_data@4A900000 {
+			no-map;
+			reg = <0x0 0x4a900000 0x0 0x1900000>;
+		};
+
+		q6_ipq5332_data: q6_ipq5332_data@4C200000 {
+			no-map;
+			reg = <0x0 0x4C200000 0x0 0x1500000>;
+		};
+
+		m3_dump: m3_dump@4D700000 {
+			no-map;
+			reg = <0x0 0x4D700000 0x0 0x100000>;
+		};
+
+		q6_etr_region: q6_etr_dump@4D800000 {
+			no-map;
+			reg = <0x0 0x4D800000 0x0 0x100000>;
+		};
+
+		q6_ipq5332_caldb: q6_ipq5332_caldb@4D900000 {
+			no-map;
+			reg = <0x0 0x4D900000 0x0 0x500000>;
+		};
+
+		q6_qcn6432_data_1: q6_qcn6432_data_1@4DE00000 {
+			no-map;
+			reg = <0x0 0x4DE00000 0x0 0x1500000>;
+		};
+
+		m3_dump_qcn6432_1: m3_dump_qcn6432_1@4F300000 {
+			no-map;
+			reg = <0x0 0x4F300000 0x0 0x100000>;
+        };
+
+		q6_qcn6432_etr_1: q6_qcn6432_etr_1@4F400000 {
+			no-map;
+			reg = <0x0 0x4F400000 0x0 0x100000>;
+		};
+
+		q6_qcn6432_caldb_1: q6_qcn6432_caldb_1@4F500000 {
+			no-map;
+			reg = <0x0 0x4F500000 0x0 0x500000>;
+		};
+
+		q6_qcn6432_data_2: q6_qcn6432_data_2@4FA00000 {
+			no-map;
+			reg = <0x0 0x4FA00000 0x0 0x1500000>;
+		};
+
+		m3_dump_qcn6432_2: m3_dump_qcn6432_2@50F00000 {
+			no-map;
+			reg = <0x0 0x50F00000 0x0 0x100000>;
+		};
+
+		q6_qcn6432_etr_2: q6_qcn6432_etr_2@51000000 {
+			no-map;
+			reg = <0x0 0x51000000 0x0 0x100000>;
+		};
+
+		q6_qcn6432_caldb_2: q6_qcn6432_caldb_2@51100000 {
+			no-map;
+			reg = <0x0 0x51100000 0x0 0x500000>;
+		};
+
+		mlo_global_mem0: mlo_global_mem_0@51600000 {
+			no-map;
+			reg = <0x0 0x51600000 0x0 0xC00000>;
+		};
+	};
+#endif
+
+	aliases {
+		serial0 = &blsp1_uart0;
+		serial1 = &blsp1_uart1;
+		ethernet0 = "/soc/dp1";
+		ethernet1 = "/soc/dp2";
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc@0 {
+		mdio:mdio@90000 {
+			pinctrl-0 = <&mdio1_pins>;
+			pinctrl-names = "default";
+			/*gpio22 is for wan napa, gpio51 for lan napa*/
+			phy-reset-gpio = <&tlmm 51 GPIO_ACTIVE_LOW>;
+			status = "okay";
+
+			phy2: ethernet-phy@2 {
+				reg = <28>;
+			};
+		};
+
+		leds {
+			compatible = "gpio-leds";
+			pinctrl-0 = <&led_pins>;
+			pinctrl-names = "default";
+			led_blue{
+				label = "led_blue";
+				gpio = <&tlmm 22 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "led_blue";
+				default-state = "off";
+			};
+			led_green {
+				label = "led_green";
+				gpio = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "led_green";
+				default-state = "on";
+			};
+			led_white {
+				label = "led_white";
+				gpio = <&tlmm 43 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "led_white";
+				default-state = "off";
+			};
+			led_red {
+				label = "led_red";
+				gpio = <&tlmm 44 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "led_red";
+				default-state = "off";
+			};
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&button_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+
+			button@1 {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		ess-instance {
+			ess-switch@3a000000 {
+				switch_cpu_bmp = <0x1>;  /* cpu port bitmap */
+				switch_lan_bmp = <0x4>; /* lan port bitmap */
+				switch_wan_bmp = <0x0>; /* wan port bitmap */
+				switch_mac_mode = <0xf>; /* mac mode for uniphy instance0*/
+				switch_mac_mode1 = <0xc>; /* mac mode for uniphy instance1*/
+				switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
+				qcom,port_phyinfo {
+					port@0 {
+						port_id = <2>;
+						phy_address = <28>;
+					};
+				};
+				qcom,port_ledinfo {
+					port@0 {
+						port = <2>;
+						led_source@0 {
+							source = <0>;
+							mode = "normal";
+							speed = "2500M";
+							active = "high";
+							blink_en = "enable";
+						};
+						led_source@1 {
+							source = <1>;
+							mode = "normal";
+							speed = "10M", "100M","1000M";
+							active = "high";
+							blink_en = "enable";
+						};
+					};
+				};
+			};
+		};
+
+		dp1 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			qcom,id = <2>;
+			reg = <0x3a504000 0x4000>;
+			qcom,mactype = <1>;
+			local-mac-address = [000000000000];
+			mdio-bus = <&mdio>;
+			qcom,phy-mdio-addr = <28>;
+			qcom,link-poll = <1>;
+			phy-mode = "sgmii";
+		};
+
+		nss-macsec0 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <28>;
+			mdiobus = <&mdio>;
+		};
+
+		/* EDMA host driver configuration for the board */
+		edma@3ab00000 {
+			qcom,txdesc-ring-start = <4>;		/* Tx desc ring start ID */
+			qcom,txdesc-rings = <12>;		/* Total number of Tx desc rings to be provisioned */
+			qcom,mht-txdesc-rings = <8>;            /* Extra Tx desc rings to be provisioned for MHT SW ports */
+			qcom,txcmpl-ring-start = <4>;		/* Tx complete ring start ID */
+			qcom,txcmpl-rings = <12>;		/* Total number of Tx complete rings to be provisioned */
+			qcom,mht-txcmpl-rings = <8>;            /* Extra Tx complete rings to be provisioned for mht sw ports. */
+			qcom,rxfill-ring-start = <4>;		/* Rx fill ring start ID */
+			qcom,rxfill-rings = <4>;		/* Total number of Rx fill rings to be provisioned */
+			qcom,rxdesc-ring-start = <12>;		/* Rx desc ring start ID */
+			qcom,rxdesc-rings = <4>;		/* Total number of Rx desc rings to be provisioned */
+			qcom,rx-page-mode = <0>;		/* Rx fill ring page mode */
+			qcom,tx-map-priority-level = <1>;	/* Tx priority level per port */
+			qcom,rx-map-priority-level = <1>;	/* Rx priority level per core */
+			qcom,ppeds-num = <2>;			/* Number of PPEDS nodes */
+			/* PPE-DS node format: <Rx-fill Tx-cmpl Rx Tx Queue-base Queue-count> */
+			qcom,ppeds-map = <1 1 1 1 32 8>,	/* PPEDS Node#0 ring and queue map */
+					<2 2 2 2 40 8>;		/* PPEDS Node#1 ring and queue map */
+			qcom,txdesc-map = <8 9 10 11>,		/* Port0 per-core Tx ring map */
+					<12 13 14 15>,        /* MHT-Port1 per-core Tx ring map */
+					<4 5 6 7>,            /* MHT-Port2 per-core Tx ring map/packets from  vp*/
+					<16 17 18 19>,        /* MHT-Port3 per-core Tx ring map */
+					<20 21 22 23>;        /* MHT-Port4 per-core Tx ring map */
+			qcom,txdesc-fc-grp-map = <1 2 3 4 5>;   /* Per GMAC flow control group map */
+			qcom,rxfill-map = <4 5 6 7>;		/* Per-core Rx fill ring map */
+			qcom,rxdesc-map = <12 13 14 15>;	/* Per-core Rx desc ring map */
+			qcom,rx-queue-start = <0>;		/* Rx queue start */
+			qcom,rx-ring-queue-map = <0 8 16 24>,	/* Priority 0 queues per-core Rx ring map */
+						<1 9 17 25>,	/* Priority 1 queues per-core Rx ring map */
+						<2 10 18 26>,	/* Priority 2 queues per-core Rx ring map */
+						<3 11 19 27>,	/* Priority 3 queues per-core Rx ring map */
+						<4 12 20 28>,	/* Priority 4 queues per-core Rx ring map */
+						<5 13 21 29>,	/* Priority 5 queues per-core Rx ring map */
+						<6 14 22 30>,	/* Priority 6 queues per-core Rx ring map */
+						<7 15 23 31>;	/* Priority 7 queues per-core Rx ring map */
+			interrupts = <0 163 4>,			/* Tx complete ring id #4 IRQ info */
+				   <0 164 4>,			/* Tx complete ring id #5 IRQ info */
+				   <0 165 4>,			/* Tx complete ring id #6 IRQ info */
+				   <0 166 4>,			/* Tx complete ring id #7 IRQ info */
+				   <0 167 4>,			/* Tx complete ring id #8 IRQ info */
+				   <0 168 4>,			/* Tx complete ring id #9 IRQ info */
+				   <0 169 4>,			/* Tx complete ring id #10 IRQ info */
+				   <0 170 4>,			/* Tx complete ring id #11 IRQ info */
+				   <0 171 4>,			/* Tx complete ring id #12 IRQ info */
+				   <0 172 4>,			/* Tx complete ring id #13 IRQ info */
+				   <0 173 4>,			/* Tx complete ring id #14 IRQ info */
+				   <0 174 4>,			/* Tx complete ring id #15 IRQ info */
+				   <0 139 4>,			/* Rx desc ring id #12 IRQ info */
+				   <0 140 4>,			/* Rx desc ring id #13 IRQ info */
+				   <0 141 4>,			/* Rx desc ring id #14 IRQ info */
+				   <0 142 4>,			/* Rx desc ring id #15 IRQ info */
+				   <0 191 4>,			/* Misc error IRQ info */
+				<0 160 4>,			/* PPEDS Node #1(TxComp ring id #1) TxComplete IRQ info */
+				<0 128 4>,			/* PPEDS Node #1(Rx Desc ring id #1) Rx Desc IRQ info */
+				<0 152 4>,			/* PPEDS Node #1(RxFill Desc ring id #1) Rx Fill IRQ info */
+				<0 161 4>,			/* PPEDS Node #2(TxComp ring id #2) TxComplete IRQ info */
+				<0 129 4>,			/* PPEDS Node #2(Rx Desc ring id #2) Rx Desc IRQ info */
+				<0 153 4>,                      /* PPEDS Node #2(RxFill Desc ring id #2) Rx Fill IRQ info */
+				<0 175 4>,                   /* MHT port Tx complete ring id #16 IRQ info */
+				<0 176 4>,                   /* MHT port Tx complete ring id #17 IRQ info */
+				<0 177 4>,                   /* MHT port Tx complete ring id #18 IRQ info */
+				<0 178 4>,                   /* MHT port Tx complete ring id #19 IRQ info */
+				<0 179 4>,                   /* MHT port Tx complete ring id #20 IRQ info */
+				<0 180 4>,                   /* MHT port Tx complete ring id #21 IRQ info */
+				<0 181 4>,                   /* MHT port Tx complete ring id #22 IRQ info */
+				<0 182 4>;                   /* MHT port Tx complete ring id #23 IRQ info */
+		};
+
+		wsi: wsi {
+			id = <0>;
+			num_chip = <2>;
+			chip_info = <0 1 1>,
+				    <1 1 0>;
+		};
+
+		q6v5_wcss: remoteproc@d100000 {
+			boot-args = <0x1 0x4 0x3 0x0 0x26 0x2>,
+					<0x1 0x4 0x4 0x1 0x2f 0x2>;
+			memory-region = <&q6_mem_regions>;
+
+			/delete-node/ remoteproc_pd1;
+			/delete-node/ remoteproc_pd2;
+			/delete-node/ remoteproc_pd3;
+
+			q6_wcss_pd4: remoteproc_pd4 {
+				compatible = "qcom,ipq5332-mpd-upd-text";
+				firmware = "IPQ5332/q6_fw4.mdt";
+
+				q6_wcss_pd1: remoteproc_pd1 {
+					compatible = "qcom,ipq5332-wcss-ahb-mpd";
+					firmware = "IPQ5332/q6_fw1.mdt";
+					m3_firmware = "IPQ5332/iu_fw.mdt";
+					interrupts-extended = <&wcss_smp2p_in 8 0>,
+							<&wcss_smp2p_in 9 0>,
+							<&wcss_smp2p_in 12 0>,
+							<&wcss_smp2p_in 11 0>;
+					interrupt-names = "fatal",
+							"ready",
+							"spawn-ack",
+							"stop-ack";
+
+					qcom,smem-states = <&wcss_smp2p_out 8>,
+							<&wcss_smp2p_out 9>,
+							<&wcss_smp2p_out 10>;
+					qcom,smem-state-names = "shutdown",
+								"stop",
+								"spawn";
+					memory-region = <&q6_ipq5332_data>,
+							<&m3_dump>,
+							<&q6_etr_region>,
+							<&q6_ipq5332_caldb>;
+				};
+
+				q6_wcss_pd2: remoteproc_pd2 {
+					compatible = "qcom,ipq5332-wcss-pcie-mpd";
+					firmware = "IPQ5332/q6_fw2.mdt";
+					m3_firmware = "qcn6432/iu_fw.mdt";
+					interrupts-extended = <&wcss_smp2p_in 16 0>,
+							<&wcss_smp2p_in 17 0>,
+							<&wcss_smp2p_in 20 0>,
+							<&wcss_smp2p_in 19 0>;
+					interrupt-names = "fatal",
+							"ready",
+							"spawn-ack",
+							"stop-ack";
+
+					qcom,smem-states = <&wcss_smp2p_out 16>,
+							<&wcss_smp2p_out 17>,
+							<&wcss_smp2p_out 18>;
+					qcom,smem-state-names = "shutdown",
+								"stop",
+								"spawn";
+					memory-region = <&q6_qcn6432_data_1>,
+							<&m3_dump_qcn6432_1>,
+							<&q6_qcn6432_etr_1>,
+							<&q6_qcn6432_caldb_1>;
+					status = "okay";
+				};
+
+				q6_wcss_pd3: remoteproc_pd3 {
+					compatible = "qcom,ipq5332-wcss-pcie-mpd";
+					firmware = "IPQ5332/q6_fw3.mdt";
+					interrupts-extended = <&wcss_smp2p_in 24 0>,
+							<&wcss_smp2p_in 25 0>,
+							<&wcss_smp2p_in 28 0>,
+							<&wcss_smp2p_in 27 0>;
+					interrupt-names = "fatal",
+							"ready",
+							"spawn-ack",
+							"stop-ack";
+
+					qcom,smem-states = <&wcss_smp2p_out 24>,
+							<&wcss_smp2p_out 25>,
+							<&wcss_smp2p_out 26>;
+					qcom,smem-state-names = "shutdown",
+								"stop",
+								"spawn";
+					memory-region = <&q6_qcn6432_data_2>,
+							<&m3_dump_qcn6432_2>,
+							<&q6_qcn6432_etr_2>,
+							<&q6_qcn6432_caldb_2>;
+					status = "okay";
+				};
+			};
+		};
+	};
+};
+
+&blsp1_uart0 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&blsp1_uart1 {
+        pinctrl-0 = <&serial_1_pins>;
+        pinctrl-names = "default";
+        status = "disabled";
+};
+
+&blsp1_i2c1 {
+	clock-frequency  = <400000>;
+	pinctrl-0 = <&i2c_1_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&blsp1_spi0 {
+	pinctrl-0 = <&spi_0_data_clk_pins &spi_0_cs_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "n25q128a11", "micron,n25q128a11", "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&sdhc {
+	bus-width = <4>;
+	max-frequency = <192000000>;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-0 = <&sdc_default_state>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&xo {
+	clock-frequency = <24000000>;
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	pinctrl-0 = <&qspi_default_state>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nandcs@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+	};
+};
+
+/* PINCTRL */
+
+&tlmm {
+
+	led_pins: led_pins {
+		board_info {
+			pins = "gpio2", "gpio3";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			input-enable;
+		};
+
+		apd_dc_in {
+			pins = "gpio24";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down; //Adapter un-plug
+			input-enable;
+		};
+
+		poe_status {
+			pins = "gpio34";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up; //AF
+			input-enable;
+		};
+
+		/* To MR pin */
+		rst_mb {
+			pins = "gpio29";
+			function = "gpio";
+			drive-strength = <8>;
+			output-high;
+		};
+
+		led_blue {
+			pins = "gpio22";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_green {
+			pins = "gpio45";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_white {
+			pins = "gpio43";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		led_red {
+			pins = "gpio44";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	qspi_default_state: qspi-default-state {
+		qspi_clock {
+			pins = "gpio13";
+			function = "qspi_clk";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		qspi_cs {
+			pins = "gpio12";
+			function = "qspi_cs";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		qspi_data {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "qspi_data";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	serial_1_pins: serial1-pinmux {
+		pins = "gpio33", "gpio34", "gpio35", "gpio36";
+		function = "blsp1_uart2";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	i2c_1_pins: i2c-1-state {
+		pins = "gpio29", "gpio30";
+		function = "blsp1_i2c0";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	button_pins: button-state {
+		pins = "gpio35";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	pwm_pins: pwm-state {
+		pins = "gpio46";
+		function = "pwm0";
+		drive-strength = <8>;
+	};
+
+	sdc_default_state: sdc-default-state {
+		clk-pins {
+			pins = "gpio13";
+			function = "sdc_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "gpio12";
+			function = "sdc_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "sdc_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	spi_0_data_clk_pins: spi-0-data-clk-state {
+		pins = "gpio14", "gpio15", "gpio16";
+		function = "blsp0_spi";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	spi_0_cs_pins: spi-0-cs-state {
+		pins = "gpio17";
+		function = "blsp0_spi";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	mdio1_pins: mdio1-state {
+		mux_0 {
+			pins = "gpio27";
+			function = "mdc1";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+		mux_1 {
+			pins = "gpio28";
+			function = "mdio1";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&license_manager {
+	status = "okay";
+};
+
+&usb3 {
+	qcom,select-utmi-as-pipe-clk;
+	status = "okay";
+
+	dwc3@8a00000 {
+		/delete-property/ #phy-cells;
+		/delete-property/ phys;
+		/delete-property/ phy-names;
+	};
+};
+
+&pwm {
+	pinctrl-0 = <&pwm_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&hs_m31phy_0 {
+	status = "okay";
+};
+
+&wifi0 {
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd1>;
+	qcom,rproc_rpd = <&q6v5_wcss>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
+	qcom,bdf-addr = <0x4C200000 0x4C200000 0x4C200000 0x0 0x0 0x0>;
+	qcom,caldb-addr = <0x4D900000 0x4D500000 0x0 0x0 0x0 0x0>;
+#ifdef __IPQ_MEM_PROFILE_512_MB__
+	qcom,tgt-mem-mode = <1>;
+	qcom,caldb-size = <0x300000>;
+#else
+	qcom,tgt-mem-mode = <0>;
+	qcom,caldb-size = <0x500000>;
+#endif
+	qcom,board_id = <0x12>;
+#if defined(__CNSS2__)
+	mem-region = <&q6_ipq5332_data>;
+#else
+	memory-region = <&q6_ipq5332_data>;
+#endif
+	qcom,wsi = <&wsi>;
+	qcom,wsi_index = <0>;
+	status = "okay";
+};
+
+&wifi1 {
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd2>;
+	qcom,rproc_rpd = <&q6v5_wcss>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
+	qcom,bdf-addr = <0x4DE00000 0x4D800000 0x0 0x0 0x0 0x0>;
+	qcom,caldb-addr = <0x4F500000 0x4EA00000 0x0 0x0 0x0 0x0>;
+	qcom,umac-irq-reset-addr = <0x20000884>;
+	qcom,caldb-size = <0x500000>;
+#ifdef __IPQ_MEM_PROFILE_512_MB__
+	qcom,tgt-mem-mode = <1>;
+#else
+	qcom,tgt-mem-mode = <0>;
+#endif
+	qcom,board_id = <0x060>;
+#if defined(__CNSS2__)
+	mem-region = <&q6_qcn6432_data_1>;
+#else
+	memory-region = <&q6_qcn6432_data_1>;
+#endif
+	qcom,wsi = <&wsi>;
+	qcom,wsi_index = <1>;
+	status = "disabled";
+	interrupts = <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "umac_reset";
+};
+
+&wifi2 {
+	qcom,multipd_arch;
+	qcom,rproc = <&q6_wcss_pd3>;
+	qcom,rproc_rpd = <&q6v5_wcss>;
+	qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
+	qcom,bdf-addr = <0x4FA00000 0x4EF00000 0x4FA00000 0x0 0x0 0x0>;
+	qcom,caldb-addr = <0x51100000 0x50100000 0x51100000 0x0 0x0 0x0>;
+	qcom,umac-irq-reset-addr = <0x18000884>;
+	qcom,caldb-size = <0x500000>;
+#ifdef __IPQ_MEM_PROFILE_512_MB__
+	qcom,tgt-mem-mode = <1>;
+#else
+	qcom,tgt-mem-mode = <0>;
+#endif
+	qcom,board_id = <0x070>;
+#if defined(__CNSS2__)
+	mem-region = <&q6_qcn6432_data_2>;
+#else
+	memory-region = <&q6_qcn6432_data_2>;
+#endif
+	qcom,wsi = <&wsi>;
+	qcom,wsi_index = <1>;
+	qcom,wide_band = <1>;
+	status = "okay";
+	interrupts = <GIC_SPI 410 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "umac_reset";
+};

feeds/qca-wifi-7/ipq53xx/image/ipq53xx.mk

@@ -162,6 +162,22 @@ define Device/zyxel_nwa130be
 endef
 TARGET_DEVICES += zyxel_nwa130be
 
+
+define Device/zyxel_nwa50be
+  DEVICE_TITLE := Zyxel NWA50BE
+  DEVICE_DTS := ipq5332-zyxel-nwa50be
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_DTS_CONFIG := config@mi01.3
+  IMAGES := sysupgrade.tar nand-factory.bin nand-factory.ubi
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
+  IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
+  IMAGE/nand-factory.ubi := append-ubi
+  DEVICE_PACKAGES := ath12k-wifi-zyxel-nwa50be ath12k-firmware-ipq5332-peb-peb -ath12k-firmware-qcn92xx
+endef
+TARGET_DEVICES += zyxel_nwa50be
+
 define Device/cig_wf672
   DEVICE_TITLE := CIG WF672
   DEVICE_DTS := ipq5332-cig-wf672

feeds/qca-wifi-7/ipq53xx/patches-6.1/0660-add-IPQ_MEM_PROFILE-in-arm64-kconfig.patch

@@ -0,0 +1,33 @@
+From f7b27331b915477cd289c37b56efb0d28b2d6f38 Mon Sep 17 00:00:00 2001
+From: Antonio Wu <antonio.wu@cybertan.com.tw>
+Date: Tue, 5 Aug 2025 10:39:58 +0000
+Subject: [PATCH] Add IPQ_MEM_PROFILE in arm64 kconfig
+
+---
+ arch/arm64/Kconfig | 10 ++++++++++
+ 1 file changed, 10 insertions(+)
+
+diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
+index 702a289..7864e79 100644
+--- a/arch/arm64/Kconfig
++++ b/arch/arm64/Kconfig
+@@ -2143,6 +2143,16 @@ config STACKPROTECTOR_PER_TASK
+ 	def_bool y
+ 	depends on STACKPROTECTOR && CC_HAVE_STACKPROTECTOR_SYSREG
+ 
++config IPQ_MEM_PROFILE
++	int "Select Memory Profile"
++	range 0 1024
++	default 0
++	help
++	  This option select memory profile to be used, which defines
++	  the reserved memory configuration used in device tree.
++
++	  If unsure, say 0
++
+ # The GPIO number here must be sorted by descending number. In case of
+ # a multiplatform kernel, we just want the highest value required by the
+ # selected platforms.
+-- 
+2.17.1
+

feeds/qca-wifi-7/mac80211/patches-sonicfi_rap7110c_341x/ath12k/0001-sonicfi_rap7110c-341x-therlaml-setting.patch

@@ -0,0 +1,63 @@
+Index: backports-6.5-rc3/drivers/net/wireless/ath/ath12k/thermal.h
+===================================================================
+--- backports-6.5-rc3.orig/drivers/net/wireless/ath/ath12k/thermal.h
++++ backports-6.5-rc3/drivers/net/wireless/ath/ath12k/thermal.h
+@@ -13,35 +13,35 @@
+ 
+ /* Below temperatures are in celsius */
+ #define ATH12K_THERMAL_LVL0_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 110
+-#define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 105
+-#define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 110
++#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 115
++#define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 125
+ 
+ #define ATH12K_THERMAL_LVL0_V2_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 95
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 90
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 110
+-#define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 100
++#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 110
++#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 110
+ #define ATH12K_THERMAL_LVL4_V2_TEMP_HIGH_MARK 120
+ 
+ #define ATH12K_THERMAL_LVL0_DUTY_CYCLE 0
+-#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 50
+-#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 90
+-#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 100
++#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 30
++#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 50
++#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 70
+ 
+-#define ATH12K_THERMAL_LVL0_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL4_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL0_V2_DUTY_CYCLE 0
++#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE 20
++#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE 40
++#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE 80
++#define ATH12K_THERMAL_LVL4_V2_DUTY_CYCLE 100
+ 
+ #define THERMAL_CONFIG_POUT0                        0
+ #define THERMAL_CONFIG_POUT1                        12

feeds/qca-wifi-7/mac80211/patches-sonicfi_rap750w_311a/ath12k/0001-sonicfi-rap750w-311a-thermal-setting.patch

@@ -0,0 +1,57 @@
+--- a/drivers/net/wireless/ath/ath12k/thermal.h
++++ b/drivers/net/wireless/ath/ath12k/thermal.h
+@@ -13,34 +13,34 @@
+ 
+ /* Below temperatures are in celsius */
+ #define ATH12K_THERMAL_LVL0_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 110
+-#define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 100
++#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 110
+ #define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 120
+ 
+ #define ATH12K_THERMAL_LVL0_V2_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 95
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 90
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 110
+-#define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 100
++#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 110
++#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 110
+ #define ATH12K_THERMAL_LVL4_V2_TEMP_HIGH_MARK 120
+ 
+ #define ATH12K_THERMAL_LVL0_DUTY_CYCLE 0
+-#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 50
+-#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 90
+-#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 100
++#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 30
++#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 50
++#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 70
+ 
+ #define ATH12K_THERMAL_LVL0_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
+ #define ATH12K_THERMAL_LVL4_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
+ 
+ #define THERMAL_CONFIG_POUT0                        0

feeds/qca-wifi-7/mac80211/patches-zyxel_nwa50be/ath12k/0001-thermal-thermal-setting.patch

@@ -0,0 +1,74 @@
+From 357da3320f8bcad056b905fb85cad3a29c343d31 Mon Sep 17 00:00:00 2001
+From: YenLin Pan <yenlin.pan@zyxel.com.tw>
+Date: Tue, 12 Aug 2025 15:41:39 +0800
+Subject: [PATCH] thermal: thermal setting
+
+lo0 -100 -hi0 105 -off0 0
+lo1 95 -hi1 110 -off1 20
+lo2 100 -hi2 115 -off2 60
+lo3 105 -hi3 119 -off3 98
+
+Signed-off-by: YenLin Pan <YenLin.Pan@zyxel.com.tw>
+---
+ drivers/net/wireless/ath/ath12k/thermal.h | 34 +++++++++++------------
+ 1 file changed, 17 insertions(+), 17 deletions(-)
+
+diff --git a/drivers/net/wireless/ath/ath12k/thermal.h b/drivers/net/wireless/ath/ath12k/thermal.h
+index 5c91906..e81f9a4 100644
+--- a/drivers/net/wireless/ath/ath12k/thermal.h
++++ b/drivers/net/wireless/ath/ath12k/thermal.h
+@@ -13,34 +13,34 @@
+ 
+ /* Below temperatures are in celsius */
+ #define ATH12K_THERMAL_LVL0_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 100
++#define ATH12K_THERMAL_LVL0_TEMP_HIGH_MARK 105
+ #define ATH12K_THERMAL_LVL1_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_TEMP_HIGH_MARK 110
+ #define ATH12K_THERMAL_LVL2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_TEMP_HIGH_MARK 115
+ #define ATH12K_THERMAL_LVL3_TEMP_LOW_MARK 105
+-#define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 120
++#define ATH12K_THERMAL_LVL3_TEMP_HIGH_MARK 119
+ 
+ #define ATH12K_THERMAL_LVL0_V2_TEMP_LOW_MARK -100
+-#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 95
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 90
+-#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 100
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 95
+-#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 105
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 100
+-#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL0_V2_TEMP_HIGH_MARK 105
++#define ATH12K_THERMAL_LVL1_V2_TEMP_LOW_MARK 95
++#define ATH12K_THERMAL_LVL1_V2_TEMP_HIGH_MARK 110
++#define ATH12K_THERMAL_LVL2_V2_TEMP_LOW_MARK 100
++#define ATH12K_THERMAL_LVL2_V2_TEMP_HIGH_MARK 115
++#define ATH12K_THERMAL_LVL3_V2_TEMP_LOW_MARK 105
++#define ATH12K_THERMAL_LVL3_V2_TEMP_HIGH_MARK 119
+ #define ATH12K_THERMAL_LVL4_V2_TEMP_LOW_MARK 105
+ #define ATH12K_THERMAL_LVL4_V2_TEMP_HIGH_MARK 120
+ 
+ #define ATH12K_THERMAL_LVL0_DUTY_CYCLE 0
+-#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 50
+-#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 90
+-#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 100
++#define ATH12K_THERMAL_LVL1_DUTY_CYCLE 20
++#define ATH12K_THERMAL_LVL2_DUTY_CYCLE 60
++#define ATH12K_THERMAL_LVL3_DUTY_CYCLE 98
+ 
+ #define ATH12K_THERMAL_LVL0_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL0_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
+-#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL1_V2_DUTY_CYCLE ATH12K_THERMAL_LVL1_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL2_V2_DUTY_CYCLE ATH12K_THERMAL_LVL2_DUTY_CYCLE
++#define ATH12K_THERMAL_LVL3_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
+ #define ATH12K_THERMAL_LVL4_V2_DUTY_CYCLE ATH12K_THERMAL_LVL3_DUTY_CYCLE
+ 
+ #define THERMAL_CONFIG_POUT0                        0
+-- 
+2.34.1
+

feeds/qca-wifi-7/qca-ssdk-qca/files-zyxel_nwa50be/qca-ssdk

@@ -0,0 +1,315 @@
+#!/bin/sh /etc/rc.common
+# Copyright (c) 2018, 2021, The Linux Foundation. All rights reserved.
+# Copyright (c) 2022-2024, Qualcomm Innovation Center, Inc. All rights reserved.
+#
+# Permission to use, copy, modify, and/or distribute this software for any
+# purpose with or without fee is hereby granted, provided that the above
+# copyright notice and this permission notice appear in all copies.
+#
+# THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+# WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+# MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+# ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+# WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+# ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+# OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+#
+
+START=16
+
+#!/bin/sh
+ruletype="ip4 ip6"
+side="wan lan"
+qwan="1 3 2 0 5 7 6 4"
+qlan="0 1 2 3 4 5 6 7"
+
+function create_war_acl_rules(){
+	for lw in $side
+	do
+		#echo $lw
+		if [ "$lw" == "wan" ];then
+			listid=254
+			queue=$qwan
+			portmap=0x20
+		else
+			listid=255
+			queue=$qlan
+			portmap=0x1e
+		fi
+		#echo $queue
+		#echo "creating list $listid"
+		ssdk_sh acl list create $listid 255
+		ruleid=0
+		for rt in $ruletype
+		do
+			for qid in $queue
+			do
+				cmd="ssdk_sh acl rule add $listid $ruleid  1 n 0 0"
+				#echo $cmd
+				if [ "$rt" == "ip4" ];then
+					cmd="$cmd ip4 n n n n n n n n n n n n n n n n n n n n n n n n n n n n n"
+					#echo $cmd
+				else
+					cmd="$cmd ip6 n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n n"
+					#echo $cmd
+				fi
+				if [ $ruleid -le 3 ];then
+					#non-zero dscp
+					cmd="$cmd y 0x0 0xff"
+				elif [ $ruleid -le 7 ];then
+					#zero dscp
+					cmd="$cmd n"
+				elif [ $ruleid -le 11 ];then
+					#non-zero dscp
+					cmd="$cmd y 0x0 0xff"
+				else
+					#zero dscp
+					cmd="$cmd n"
+				fi
+				p=$((ruleid/2))
+				cmd="$cmd y mask $((ruleid%2)) 0x1 y mask $((p%2)) 0x1 n n n n n n n n n n n n n n n y n n n n n n n y $qid n n 0 0 n n n n n n n n n n n n n n n n n n n n 0"
+				#echo $cmd
+				$cmd
+				ruleid=`expr $ruleid + 1`
+			done
+		done
+		ssdk_sh acl list bind $listid 0 1 $portmap
+	done
+}
+
+function create_war_cosmap(){
+	ssdk_sh cosmap pri2q set 0 0
+	ssdk_sh cosmap pri2q set 1 0
+	ssdk_sh cosmap pri2q set 2 0
+	ssdk_sh cosmap pri2q set 3 0
+	ssdk_sh cosmap pri2q set 4 1
+	ssdk_sh cosmap pri2q set 5 1
+	ssdk_sh cosmap pri2q set 6 1
+	ssdk_sh cosmap pri2q set 7 1
+	ssdk_sh cosmap pri2ehq set 0 0
+	ssdk_sh cosmap pri2ehq set 1 0
+	ssdk_sh cosmap pri2ehq set 2 0
+	ssdk_sh cosmap pri2ehq set 3 0
+	ssdk_sh cosmap pri2ehq set 4 1
+	ssdk_sh cosmap pri2ehq set 5 1
+	ssdk_sh cosmap pri2ehq set 6 1
+	ssdk_sh cosmap pri2ehq set 7 1
+}
+
+function create_acl_byp_egstp_rules(){
+	chip_ver=$1
+	cmd="ssdk_sh servcode config set 1 n 0 0xfffefc7f 0xffbdff 0 0 0 0 0 0"
+	if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		cmd="$cmd 0"
+	fi
+	#echo $cmd
+	$cmd
+
+	ssdk_sh acl list create 56 48
+	#action bypass eg stp check
+	action="y n n n n n n n n n n 0 0 n n n n n n n n n n n n n y n n n n n n n n n n n n y n n n n n n n n n n n n n n n n n n"
+	if [ "$chip_ver" == "0x2000" ]; then
+		action="$action n n 0"
+	elif [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		action="$action n n n 0"
+	else
+		action="$action 0"
+	fi
+
+	for ruleid in $( seq 0 2 )
+	do
+		if [ "$ruleid" == "0" ];then
+			cmd="ssdk_sh acl rule add 56 0 1 n 0 0 mac n n n n n y 01-80-c2-00-00-00 ff-ff-ff-ff-ff-ff n n n n n n n n n n n n n n n n n n n n n n n"
+		elif [ "$ruleid" == "1" ];then
+			cmd="ssdk_sh acl rule add 56 1 1 n 0 0 mac n n n n n n n yes 0x8809 0xffff n n n n n n n n n n n n n n n n n n n n n"
+		else
+			cmd="ssdk_sh acl rule add 56 2 1 n 0 0 mac n n n n n n n yes 0x888e 0xffff n n n n n n n n n n n n n n n n n n n n n"
+		fi
+		if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+			cmd="$cmd n $action"
+		else
+			cmd="$cmd $action"
+		fi
+		#echo $cmd
+		$cmd
+	done
+	ssdk_sh acl list bind 56 0 2 1
+}
+
+function delete_war_acl_rules(){
+	for lw in $side
+	do
+		#echo $lw
+		if [ "$lw" == "wan" ];then
+			listid=254
+			queue=$qwan
+			portmap=0x20
+		else
+			listid=255
+			queue=$qlan
+			portmap=0x1e
+		fi
+		ssdk_sh acl list unbind $listid 0 1 $portmap
+		for rt in $ruletype
+		do
+			for qid in $queue
+			do
+				cmd="ssdk_sh acl rule del $listid 0 1"
+				echo $cmd
+				$cmd
+			done
+		done
+		#echo "deleting list $listid"
+		ssdk_sh acl list destroy $listid
+	done
+}
+
+function delete_war_cosmap(){
+	ssdk_sh cosmap pri2q set 0 0
+	ssdk_sh cosmap pri2q set 1 0
+	ssdk_sh cosmap pri2q set 2 1
+	ssdk_sh cosmap pri2q set 3 1
+	ssdk_sh cosmap pri2q set 4 2
+	ssdk_sh cosmap pri2q set 5 2
+	ssdk_sh cosmap pri2q set 6 3
+	ssdk_sh cosmap pri2q set 7 3
+	ssdk_sh cosmap pri2ehq set 0 1
+	ssdk_sh cosmap pri2ehq set 1 0
+	ssdk_sh cosmap pri2ehq set 2 2
+	ssdk_sh cosmap pri2ehq set 3 2
+	ssdk_sh cosmap pri2ehq set 4 3
+	ssdk_sh cosmap pri2ehq set 5 3
+	ssdk_sh cosmap pri2ehq set 6 4
+	ssdk_sh cosmap pri2ehq set 7 5
+}
+
+function delete_acl_byp_egstp_rules(){
+	chip_ver=$1
+	cmd="ssdk_sh servcode config set 1 n 0 0xfffefcff 0xffbfff 0 0 0 0 0 0"
+	if [ "$chip_ver" == "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		cmd="$cmd 0"
+	fi
+	#echo $cmd
+	$cmd
+	ssdk_sh acl list unbind 56 0 2 1
+	ssdk_sh acl rule del 56 0 1
+	ssdk_sh acl rule del 56 1 1
+	ssdk_sh acl rule del 56 2 1
+	ssdk_sh acl list destroy 56
+}
+
+function edma_war_config_add(){
+	create_war_cosmap
+	ssdk_sh acl status set enable
+	create_war_acl_rules
+}
+
+function edma_war_config_del(){
+	delete_war_acl_rules
+	delete_war_cosmap
+}
+
+function ipq50xx_serdes_monitor () {
+	#if qca808x phy exist, need to monitor the serdes to avoid the effect for WIFI
+	port_id=2
+	old_linkstatus="DISABLE"
+	phy_id_info=`ssdk_sh port phyid get $port_id | grep Org | awk -F '!' '{print $2}'`
+	if [ "$phy_id_info" = "[Org ID]:0x004d[Rev ID]:0xd101" ]; then
+		ssdk_sh debug phy set 29 0xb 0x300d
+		ssdk_sh debug uniphy set 0 0x7ac 0x300d 4
+
+		while true
+		do
+			cur_linkstatus=`ssdk_sh port linkstatus get $port_id | grep Status | awk -F ':' '{print $2}'`
+			#when qca808x phy link status is from down to up, serdes tx would be enabled
+			if [ "$cur_linkstatus" = "ENABLE" ] && [ "$old_linkstatus" = "DISABLE" ]; then
+				ssdk_sh debug phy set 29 0xb 0xb00d
+				ssdk_sh debug uniphy set 0 0x7ac 0xb00d 4
+			fi
+			#when qca808x phy link status is from up to down, serdes tx would be disabled
+			if [ "$cur_linkstatus" = "DISABLE" ] && [ "$old_linkstatus" = "ENABLE" ]; then
+				ssdk_sh debug phy set 29 0xb 0x300d
+				ssdk_sh debug uniphy set 0 0x7ac 0x300d 4
+			fi
+			old_linkstatus=$cur_linkstatus
+		done
+	fi
+}
+
+function ipq53xx_phy_amplitude_set () {
+	#PHY (8081->5321): Full amplitude (bit[7:5]=000), half swing (bit[4]=1)
+	#for qca808x phy sgmii, set half amplitude with src_half_swing register
+	port_id=2
+	phy_addr=0x1d
+	phy_id_info=`ssdk_sh port phyid get $port_id | grep Org | awk -F '!' '{print $2}'`
+	if [ "$phy_id_info" = "[Org ID]:0x004d[Rev ID]:0xd101" ]; then
+		ssdk_sh debug phy set $phy_addr 0x40010087 0x208a
+		#Set the Reg0x67 bits[7:5]=3’b000 and bit4=1’b1
+		ampl_val=$(ssdk_sh debug phy get $phy_addr 0x40010067 | grep SSDK | grep -oE '0x[0-9a-fA-F]+' | sed 's/\(0x..\)./\11/')
+		ssdk_sh debug phy set $phy_addr 0x40010067 $ampl_val
+	fi
+}
+
+function ipq53xx_uniphy_amplitude_set () {
+        #UniPhy (5321->8081): Custom amplitude (bit[8:4]=21) = 0xb15d
+	#for ipq53xx sgmii, set half amplitude with tx_emp_lvl/margin_index and tx_margin
+	ssdk_sh debug uniphy set 1 0x7ac 0xb15d 4
+	ssdk_sh debug uniphy set 1 0x24 0 4
+}
+
+ssdk_dependency() {
+	counter=0
+	[ -e /lib/modules/$(uname -r)/qca-ssdk.ko ] && [ ! -d /sys/module/qca_ssdk ] && {
+		insmod qca-ssdk.ko
+	}
+	while [ ! -d /sys/ssdk ] && [ "$counter" -le 5 ]
+	do
+		sleep 1
+		counter=$((counter+1))
+	done
+}
+
+start() {
+	ssdk_dependency
+	chip_ver=`ssdk_sh debug reg get 0 4 | grep Data | tr -d 'SSDK Init OK![Data]:'`
+	#The following commands should be uncommented to enable EDMA WAR
+	if [ "$chip_ver" = "0x1401" ]; then
+		#edma_war_config_add
+		echo ''
+	fi
+	#The following commands should be uncommented to add acl egress stp bypass rules
+	if [ "$chip_ver" = "0x1500" ] || [ "$chip_ver" = "0x1501" ] || [ "$chip_ver" = "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		#create_acl_byp_egstp_rules $chip_ver
+		echo ''
+	fi
+	#The following commands should be uncommented to enable WAR for ipq50xx
+	chip_type_info=`cat tmp/sysinfo/model`
+	result=$(echo $chip_type_info | grep "IPQ5018")
+	if [ "$result" != "" ]; then
+		#ipq50xx_serdes_monitor &
+		#ipq50xx_uniphy_amplitude_set
+		#ipq50xx_phy_amplitude_set
+		echo ''
+	fi
+	if [ "$chip_ver" = "0x2001" ]; then
+		ipq53xx_uniphy_amplitude_set
+		ipq53xx_phy_amplitude_set
+		echo ''
+	fi
+	echo starting
+}
+
+stop() {
+	chip_ver=`ssdk_sh debug reg get 0 4 | grep Data | tr -d 'SSDK Init OK![Data]:'`
+	#The following commands should be uncommented to disable EDMA WAR
+	if [ "$chip_ver" = "0x1401" ]; then
+		#edma_war_config_del
+		echo ''
+	fi
+	#The following commands should be uncommented to delete acl egress stp bypass rules
+	if [ "$chip_ver" = "0x1500" ] || [ "$chip_ver" = "0x1501" ] || [ "$chip_ver" = "0x2000" ] || [ "$chip_ver" = "0x2001" ] || [ "$chip_ver" = "0x2100" ]; then
+		#delete_acl_byp_egstp_rules $chip_ver
+		echo ''
+	fi
+	echo stoping
+}

feeds/qca-wifi-7/qca-ssdk-qca/patches-zyxel_nwa50be/0001-pinctrl-make-the-switch-LED-works.patch

@@ -0,0 +1,47 @@
+From 7fa9e9b683f1c573c58a14755347988919bc7d06 Mon Sep 17 00:00:00 2001
+From: YenLin Pan <yenlin.pan@zyxel.com.tw>
+Date: Wed, 14 May 2025 13:47:06 +0800
+Subject: [PATCH] pinctrl: make the switch LED works
+
+Enable switch LED pin definition for LED0/LED1/LED2 control
+
+Signed-off-by: YenLin Pan <YenLin.Pan@zyxel.com.tw>
+---
+ src/init/ssdk_mht_pinctrl.c | 10 ++++++++--
+ 1 file changed, 8 insertions(+), 2 deletions(-)
+
+diff --git a/src/init/ssdk_mht_pinctrl.c b/src/init/ssdk_mht_pinctrl.c
+index 2debe59..1ae0002 100755
+--- a/src/init/ssdk_mht_pinctrl.c
++++ b/src/init/ssdk_mht_pinctrl.c
+@@ -33,11 +33,17 @@ static struct mht_pinctrl_setting mht_pin_settings[] = {
+     /*PINs default MUX Setting*/
+     MHT_PIN_SETTING_MUX(0,  MHT_PIN_FUNC_INTN_WOL),
+     MHT_PIN_SETTING_MUX(1,  MHT_PIN_FUNC_INTN),
+-#if 0
++#if 1
+     MHT_PIN_SETTING_MUX(2,  MHT_PIN_FUNC_P0_LED_0),
+     MHT_PIN_SETTING_MUX(3,  MHT_PIN_FUNC_P1_LED_0),
+     MHT_PIN_SETTING_MUX(4,  MHT_PIN_FUNC_P2_LED_0),
+     MHT_PIN_SETTING_MUX(5,  MHT_PIN_FUNC_P3_LED_0),
++    MHT_PIN_SETTING_MUX(6,  MHT_PIN_FUNC_P0_LED_2),
++    MHT_PIN_SETTING_MUX(7,  MHT_PIN_FUNC_P1_LED_2),
++    MHT_PIN_SETTING_MUX(8,  MHT_PIN_FUNC_P2_LED_2),
++    MHT_PIN_SETTING_MUX(9,  MHT_PIN_FUNC_P3_LED_2),
++#endif
++#if 0
+     MHT_PIN_SETTING_MUX(6,  MHT_PIN_FUNC_PPS_IN),
+     MHT_PIN_SETTING_MUX(7,  MHT_PIN_FUNC_TOD_IN),
+     MHT_PIN_SETTING_MUX(8,  MHT_PIN_FUNC_RTC_REFCLK_IN),
+@@ -49,7 +55,7 @@ static struct mht_pinctrl_setting mht_pin_settings[] = {
+     MHT_PIN_SETTING_MUX(13, MHT_PIN_FUNC_P0_TOD_OUT),
+     MHT_PIN_SETTING_MUX(14, MHT_PIN_FUNC_P0_CLK125_TDI),
+     MHT_PIN_SETTING_MUX(15, MHT_PIN_FUNC_P0_SYNC_CLKO_PTP),
+-#if 0
++#if 1
+     MHT_PIN_SETTING_MUX(16, MHT_PIN_FUNC_P0_LED_1),
+     MHT_PIN_SETTING_MUX(17, MHT_PIN_FUNC_P1_LED_1),
+     MHT_PIN_SETTING_MUX(18, MHT_PIN_FUNC_P2_LED_1),
+-- 
+2.34.1
+

feeds/tip/certificates/files/etc/init.d/early_boot

@@ -25,6 +25,11 @@ copy_certificates() {
 }
 
 boot() {
+	case "$(board_name)" in
+	sonicfi,rap6*)
+		touch /tmp/squashfs
+	;;
+	esac
 	[ -f /etc/ucentral/key.pem ] && return
 	/usr/bin/mount_certs
 	copy_certificates

feeds/tip/certificates/files/usr/bin/mount_certs

@@ -37,13 +37,16 @@ sonicfi,rap7*)
 		mtd=$(find_mtd_index certificates)
 		[ -n "$mtd" ] && mount -t ext4 /dev/mtdblock$mtd /certificates
 	fi
-	if [ ! -f /certificates/cert.pem ] || [ ! -f /certificates/key.pem ]; then
-		part=$(tar_part_lookup "0:BOOTCONFIG" "0:BOOTCONFIG1")
-		if [ -n "part" ]; then
-			mmc_dev=$(echo $(find_mmc_part "$part") | sed 's/^.\{5\}//')
-			[ -n "$mmc_dev" ] && tar xf /dev/$mmc_dev -C /certificates
-		fi
+	;;
+sonicfi,rap6*)
+	mtd=$(find_mtd_index certificates)
+	if [ "$(head -c 4 /dev/mtd$mtd)" == "hsqs" ]; then
+		mount -t squashfs /dev/mtdblock$mtd /mnt
+		cp /mnt/* /certificates
+		umount /mnt
 	fi
+		mtd=$(find_mtd_index devinfo)
+		[ -n "$mtd" ] && tar xf /dev/mtdblock$mtd -C /certificates
 	;;
 udaya,a5-id2|\
 yuncore,ax820)
@@ -59,19 +62,6 @@ yuncore,ax820)
 		[ -n "$mtd" ] && tar xf /dev/mtdblock$mtd -C /certificates
 	fi
 	;;
-sonicfi,rap6*)
-	mtd=$(find_mtd_index certificates)
-	if [ "$(head -c 4 /dev/mtd$mtd)" == "hsqs" ]; then
-		mount -t squashfs /dev/mtdblock$mtd /mnt
-		cp /mnt/* /certificates
-		umount /mnt
-	fi
-	part=$(tar_part_lookup "devinfo" "certificates")
-	if [ -n "$part" ]; then
-		mtd=$(find_mtd_index $part)
-		[ -n "$mtd" ] && tar xf /dev/mtdblock$mtd -C /certificates
-	fi
-	;;
 *)
 	mtd=$(find_mtd_index certificates)
 

feeds/tip/certificates/files/usr/bin/store_certs

@@ -14,13 +14,6 @@ tar_part_lookup() {
 
 . /lib/functions.sh
 case "$(board_name)" in
-sonicfi,rap7110c-341x)
-	cd /certificates
-	tar cf /tmp/certs.tar .
-	part=$(tar_part_lookup "0:BOOTCONFIG" "0:BOOTCONFIG1")
-	mmc_dev=$(echo $(find_mmc_part $part) | sed 's/^.\{5\}//')
-	dd if=/tmp/certs.tar of=/dev/$mmc_dev
-	;;
 udaya,a5-id2|\
 yuncore,ax820)
 	cd /certificates
@@ -33,8 +26,7 @@ sonicfi,rap6*)
 	if [ "$(fw_printenv -n store_certs_disabled)" != "1" ]; then
 		cd /certificates
 		tar cf /tmp/certs.tar .
-		part=$(tar_part_lookup "devinfo" "certificates")
-		mtd=$(find_mtd_index $part)
+		mtd=$(find_mtd_index devinfo)
 		block_size=$(cat /sys/class/mtd/mtd$mtd/size)
 		dd if=/tmp/certs.tar of=/tmp/certs_pad.tar bs=$block_size conv=sync
 		mtd write /tmp/certs_pad.tar /dev/mtd$mtd

feeds/tip/cloud_discovery/files/usr/share/ucentral/cloud_discovery.uc

@@ -5,8 +5,8 @@ import * as fs from 'fs';
 
 let cmd = ARGV[0];
 let ifname = getenv("interface");
-let opt138 = getenv("opt138");
-let opt224 = getenv("opt224");
+let opt138 = fs.readfile('/tmp/dhcp-option-138');
+let opt224 = fs.readfile('/tmp/dhcp-option-224');
 
 if (cmd != 'bound' && cmd != 'renew')
 	exit(0);
@@ -23,14 +23,14 @@ let cloud = {
 	lease: true,
 };
 if (opt138) {
-	let dhcp = hexdec(opt138);
+	let dhcp = opt138;
 	dhcp = split(dhcp, ':');
 	cloud.dhcp_server = dhcp[0];
 	cloud.dhcp_port = dhcp[1] ?? 15002;
 	cloud.no_validation = true;
 }
 if (opt224) {
-	let dhcp = hexdec(opt224);
+	let dhcp = opt224;
 	dhcp = split(dhcp, ':');
 	cloud.dhcp_server = dhcp[0];
 	cloud.dhcp_port = dhcp[1] ?? 15002;

feeds/ucentral/ucentral-schema/Makefile

@@ -4,9 +4,10 @@ PKG_NAME:=ucentral-schema
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-schema.git
+PKG_MIRROR_HASH:=dd37ce95e77af90424d4792f1d292e90242d66ebf5c6552afdf364fd33c58af8
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_DATE:=2025-08-04
-PKG_SOURCE_VERSION:=1c6b3095cb9e398fcbfcb2bf995365066eb76b21
+PKG_SOURCE_DATE:=2025-08-12
+PKG_SOURCE_VERSION:=a1e7571a07ad309301954149884b13f71fbf74be
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

feeds/ucentral/udhcpinject/Makefile

@@ -12,7 +12,7 @@ define Package/udhcpinject
 	SECTION:=net
 	CATEGORY:=Network
 	TITLE:=An agent to inject DHCP option
-	DEPENDS:=+libpcap +kmod-ifb +tc
+	DEPENDS:=+libpcap +kmod-ifb +tc +libuci
 	MAINTAINER:=kmk <alex18_huang@accton.com>
 endef
 
@@ -41,4 +41,4 @@ define Package/udhcpinject/install
 	$(CP) ./files/* $(1)/
 endef
 
-$(eval $(call BuildPackage,udhcpinject))
+$(eval $(call BuildPackage,udhcpinject))

feeds/ucentral/udhcpinject/files/etc/config/dhcpinject

@@ -1,10 +1,19 @@
-# config device 'uplink'
-#   list port 'eth0'
-#
-# config ssids 'ssids'
-#   list ssid 'EAP101-ERICHI'
-#   list ssid 'EAP101-AKIHO'
-#   list ssid 'EAP101-DAMAYU'
-#
-# config dhcpinject 'dhcpinject'
-#   option iface_count '6'
+#config network 'wan0'
+#        option upstream 'up0v0'
+#        list ssid5G '18-KMK-YAYA'
+#        list ssid5G '18-KMK-AKIHO'
+#        list ssid2G '18-KMK-YAYA'
+#        list ssid2G '18-KMK-AKIHO'
+#        option count '4'
+
+#config network 'wan284'
+#        option upstream 'up1v284'
+#        list ssid5G '18-KMK-SARAN'
+#        list ssid2G '18-KMK-SARAN'
+#        option count '2'
+
+#config network 'wan283'
+#        option upstream 'up2v283'
+#        list ssid5G '18-KMK-ERICHI'
+#        list ssid2G '18-KMK-ERICHI'
+#        option count '2'

feeds/ucentral/udhcpinject/files/etc/init.d/dhcpinject

@@ -9,55 +9,18 @@ SERVICE_NAME="dhcpinject"
 PROG=/usr/bin/udhcpinject
 
 start_service() {
-    local ssids=""
-    local ports=""
-    local ifaces=""
-
-    # Function to process each ssid
-    append_ssid() {
-        local value="$1"
-        if [ -n "$ssids" ]; then
-            ssids="$ssids,$value"
-        else
-            ssids="$value"
-        fi
-    }
-
-    append_port() {
-        local value="$1"
-        if [ -n "$ports" ]; then
-            ports="$ports,$value"
-        else
-            ports="$value"
-        fi
-    }
-
-    # Load the dhcpinject config
-    config_load dhcpinject
-
-    # Get the list of SSIDs
-    config_list_foreach ssids ssid append_ssid
-
-    # Get the list of ports
-    config_list_foreach uplink port append_port
-
-    # Get the iface_count
-    config_get ifaces dhcpinject iface_count
-    
-    # Fallback to eth0 if no ports are specified
-    if [ -z "$ports" ]; then
-        ports="eth0"
+    # check if config file has contents by executing `uci get dhcpinject.@network[0]`
+    if [ -z "$(uci get dhcpinject.@network[0] 2>/dev/null)" ]; then
+        echo "No upstreams specified, exiting $SERVICE_NAME"
+        return 0
     fi
-
-    # Optional: Log or echo for debugging
-    logger -t dhcp_inject "Generated SSIDs=$ssids, Uplink=$ports, IFACEs=$ifaces"
+    # Wait for wifi to be up
+    ubus -t 90 wait_for network.wireless
 
     procd_open_instance "$SERVICE_NAME"
     procd_set_param command $PROG
-    procd_set_param env SSIDs="$ssids" PORTs="$ports" IFACEs="$ifaces"
     procd_set_param respawn 3600 10 10
     procd_set_param file /etc/config/dhcpinject
-    procd_set_param reload_signal SIGHUP
     procd_close_instance
 }
 

feeds/ucentral/udhcpinject/src/Makefile

@@ -7,10 +7,10 @@ obj-y := udhcpinject.o
 all: udhcpinject
 
 udhcpinject: $(obj-y)
-	$(CC) $(LDFLAGS) -lpcap -o $@ $(obj-y)
+	$(CC) $(LDFLAGS) -lpcap -luci -o $@ $(obj-y)
 
 %.o: %.c
 	$(CC) $(CFLAGS) $(TARGET_CFLAGS) -c $< -o $@
 
 clean:
-	rm -f *.o udhcpinject
+	rm -f *.o udhcpinject

feeds/ucentral/udhcpinject/src/udhcpinject.c

@@ -6,286 +6,81 @@
 #include <linux/ip.h>
 #include <linux/udp.h>
 #include <net/if.h>
-#include <netinet/in.h>
+
 #include <pcap.h>
 #include <signal.h>
-#include <stdio.h>
-#include <stdlib.h>
-#include <string.h>
+
 #include <sys/socket.h>
 #include <syslog.h>
 #include <unistd.h>
+#include <uci.h>
 
 #include "udhcpinject.h"
 
-#define MAX_INTERFACES 48
-#define MAX_PORTS 8
-
-// Global variables
-struct iface_info *iface_map = NULL;
-static struct port_info *ports = NULL;
-int iface_count = 0;
-int port_count = 0;
-int total_iface = 0;
-static pcap_t *handle = NULL;
-static char *provided_ssids = NULL;
-static char *provided_ports = NULL;
-
-// Function to cleanup tc rules
-void cleanup_tc() {
-    char cmd[1024];
-    for (int i = 0; i < iface_count; i++) {
-        snprintf(cmd, sizeof(cmd), "tc filter del dev %s ingress pref 32 2>/dev/null",
-                 iface_map[i].iface);
-        system(cmd);
-    }
-}
-
 // Cleanup function
-void cleanup() {
+void cleanup()
+{
     syslog(LOG_INFO, "Cleaning up resources...\n");
-    cleanup_tc();
 
-    if (handle) {
+    if (handle)
+    {
         pcap_close(handle);
         handle = NULL;
     }
-    if (ports) {
-        for (int i = 0; i < port_count; i++) {
-            if (ports[i].sock >= 0) {
-                close(ports[i].sock);
-            }
+
+    if (iface_map)
+    {
+        char cmd[1024];
+        for (int i = 0; i < iface_map_size; i++)
+        {
+            snprintf(cmd, sizeof(cmd), "tc filter del dev %s ingress pref 32 2>/dev/null",
+                     iface_map[i].iface);
+            system(cmd);
         }
-        free(ports);
-        ports = NULL;
-        port_count = 0;
-    }
-    if (iface_map) {
         free(iface_map);
-        iface_map = NULL;
-        iface_count = 0;
     }
-    if (provided_ssids) {
-        free(provided_ssids);
-        provided_ssids = NULL;
-    }
-    if (provided_ports) {
-        free(provided_ports);
-        provided_ports = NULL;
+
+    if (port_map)
+    {
+        for (int i = 0; i < port_map_size; i++)
+        {
+            close(port_map[i].sock);
+        }
+        free(port_map);
     }
+
     syslog(LOG_INFO, "Cleanup complete.\n");
 }
 
-// Function to parse SSIDs and populate iface_map
-int parse_ssids(const char *ssids) {
-    if (iface_map) {
-        free(iface_map);
-        iface_map = NULL;
-        iface_count = 0;
-    }
-
-    // Create a set of provided SSIDs for efficient lookup
-    char ssids_copy[256];
-    strncpy(ssids_copy, ssids, sizeof(ssids_copy) - 1);
-    ssids_copy[sizeof(ssids_copy) - 1] = '\0';
-
-    // Count number of SSIDs for allocation
-    int ssid_count = 1; // Start at 1 for first SSID
-    for (int i = 0; ssids_copy[i]; i++) {
-        if (ssids_copy[i] == ',')
-            ssid_count++;
-    }
-
-    char **ssid_set = malloc(ssid_count * sizeof(char *));
-    if (!ssid_set) {
-        syslog(LOG_ERR, "Failed to allocate memory for SSID set\n");
-        return -1;
-    }
-
-    int ssid_idx = 0;
-    char *token = strtok(ssids_copy, ",");
-    while (token) {
-        ssid_set[ssid_idx++] = token;
-        token = strtok(NULL, ",");
-    }
-
-    // Execute iwinfo command and capture output
-    FILE *pipe = popen("iwinfo | grep wlan -A1 | grep -v \"^--\" | tr -d '\"' "
-                       "| awk '/wlan/ {name=$1; essid=$3} /Access Point/ "
-                       "{print name \"=\" essid \",\" $3}' | tr -d ':'",
-                       "r");
-    if (!pipe) {
-        syslog(LOG_ERR, "Failed to execute iwinfo command\n");
-        free(ssid_set);
-        return -1;
-    }
-
-    char line[256];
-    while (fgets(line, sizeof(line), pipe) != NULL) {
-        // Remove trailing newline
-        line[strcspn(line, "\n")] = 0;
-
-        // Parse line format: wlanX=SSID,BSSID
-        char *iface = strtok(line, "=");
-        char *rest = strtok(NULL, "=");
-        if (!iface || !rest)
-            continue;
-
-        char *essid = strtok(rest, ",");
-        char *bssid = strtok(NULL, ",");
-        if (!essid || !bssid)
-            continue;
-
-        // Check if this SSID is in our provided set
-        int match = 0;
-        for (int i = 0; i < ssid_idx; i++) {
-            if (strcmp(essid, ssid_set[i]) == 0) {
-                match = 1;
-                break;
-            }
-        }
-
-        if (!match)
-            continue;
-
-        // Add matching interface to iface_map
-        if (iface_count >= MAX_INTERFACES) {
-            syslog(LOG_ERR, "Too many matching interfaces, max is %d\n",
-                   MAX_INTERFACES);
-            pclose(pipe);
-            free(ssid_set);
-            return -1;
-        }
-
-        iface_map =
-            realloc(iface_map, (iface_count + 1) * sizeof(struct iface_info));
-        if (!iface_map) {
-            syslog(LOG_ERR, "Failed to reallocate iface_map\n");
-            pclose(pipe);
-            free(ssid_set);
-            return -1;
-        }
-
-        struct iface_info *info = &iface_map[iface_count];
-        info->serial = iface_count + 1;
-
-        strncpy(info->iface, iface, LEN_IFACE);
-        info->iface[LEN_IFACE] = '\0';
-
-        strncpy(info->essid, essid, LEN_ESSID);
-        info->essid[LEN_ESSID] = '\0';
-
-        strncpy(info->bssid, bssid, LEN_BSSID);
-        info->bssid[LEN_BSSID] = '\0';
-
-        iface_count++;
-    }
-
-    int pipe_status = pclose(pipe);
-    if (pipe_status == -1) {
-        syslog(LOG_ERR, "Error closing iwinfo pipe: %s\n", strerror(errno));
-    }
-
-    free(ssid_set);
-
-    if (iface_count == 0) {
-        syslog(LOG_ERR, "No matching interfaces found for provided SSIDs\n");
-        return -1;
-    }
-
-    if (iface_count != total_iface) {
-        syslog(LOG_ERR, "Expect %d but only %d interfaces were found.\n", total_iface, iface_count);
-        return -1;
-    }
-
-    syslog(LOG_INFO, "Found %d matching interfaces\n", iface_count);
-    return 0;
-}
-
-int parse_ports(const char *port_list) {
-    if (ports) {
-        for (int i = 0; i < port_count; i++) {
-            if (ports[i].sock >= 0) {
-                close(ports[i].sock);
-            }
-        }
-        free(ports);
-        ports = NULL;
-        port_count = 0;
-    }
-
-    char ports_copy[256];
-    strncpy(ports_copy, port_list, sizeof(ports_copy) - 1);
-    ports_copy[sizeof(ports_copy) - 1] = '\0';
-
-    port_count = 1;
-    for (int i = 0; ports_copy[i]; i++) {
-        if (ports_copy[i] == ',') {
-            port_count++;
-        }
-    }
-
-    if (port_count > MAX_PORTS) {
-        syslog(LOG_ERR, "Too many ports specified, maximum is %d\n", MAX_PORTS);
-        return -1;
-    }
-
-    ports = calloc(port_count, sizeof(struct port_info));
-    if (!ports) {
-        syslog(LOG_ERR, "Failed to allocate memory for ports\n");
-        return -1;
-    }
-
-    char *token = strtok(ports_copy, ",");
-    int idx = 0;
-    while (token && idx < port_count) {
-        strncpy(ports[idx].name, token, LEN_IFACE);
-        ports[idx].name[LEN_IFACE] = '\0';
-
-        ports[idx].sock = socket(AF_PACKET, SOCK_RAW, htons(ETH_P_ALL));
-        if (ports[idx].sock < 0) {
-            syslog(LOG_ERR, "Socket creation failed for %s: %s\n",
-                   ports[idx].name, strerror(errno));
-            return -1;
-        }
-
-        ports[idx].ifindex = if_nametoindex(ports[idx].name);
-        if (ports[idx].ifindex == 0) {
-            syslog(LOG_ERR, "Failed to get interface index for %s: %s\n",
-                   ports[idx].name, strerror(errno));
-            return -1;
-        }
-
-        token = strtok(NULL, ",");
-        idx++;
-    }
-
-    syslog(LOG_INFO, "Configured %d ports for forwarding\n", port_count);
-    return 0;
-}
-
-int setup_tc() {
-    char cmd[1024];
+int setup_tc()
+{
+    char cmd[512];
 
+    // check if ifb-inject exists, if not create it
     snprintf(cmd, sizeof(cmd), "ip link show ifb-inject >/dev/null 2>&1");
-    if (system(cmd) != 0) {
+    if (system(cmd) != 0)
+    {
         snprintf(cmd, sizeof(cmd),
                  "ip link add name ifb-inject type ifb && ip link set "
                  "ifb-inject up");
-        if (system(cmd) != 0) {
+        if (system(cmd) != 0)
+        {
             syslog(LOG_ERR, "Failed to setup ifb-inject\n");
             return -1;
         }
     }
 
-    for (int i = 0; i < iface_count; i++) {
-        snprintf(cmd, sizeof(cmd), "tc qdisc add dev %s ingress 2>/dev/null 1>2", 
-            iface_map[i].iface);
+    for (int i = 0; i < iface_map_size; i++)
+    {
+        snprintf(cmd, sizeof(cmd), "tc qdisc add dev %s ingress 2>/dev/null 1>2",
+                 iface_map[i].iface);
         int result = system(cmd);
-        if (result == 2) {
+        if (result == 2)
+        {
             syslog(LOG_INFO, "Ingress qdisc already exists for %s\n", iface_map[i].iface);
         }
-        else if (result == 1) {
+        else if (result == 1)
+        {
             syslog(LOG_ERR, "Failed to add qdisc for %s\n", iface_map[i].iface);
             return -1;
         }
@@ -300,7 +95,8 @@ int setup_tc() {
                  "action mirred egress mirror dev ifb-inject pipe "
                  "action drop",
                  iface_map[i].iface, iface_map[i].serial);
-        if (system(cmd) != 0) {
+        if (system(cmd) != 0)
+        {
             syslog(LOG_ERR, "Failed to setup tc for %s\n", iface_map[i].iface);
             return -1;
         }
@@ -308,82 +104,172 @@ int setup_tc() {
     return 0;
 }
 
-// Signal handler
-void signal_handler(int sig) {
-    if (sig == SIGTERM) {
-        syslog(LOG_INFO, "Received SIGTERM, cleaning up...\n");
-        cleanup();
-        exit(0);
-    } else if (sig == SIGHUP) {
-        syslog(LOG_INFO, "Received reload signal, reconfiguring...\n");
-        // Clean up existing resources
-        cleanup_tc();
-        
-        // Free old SSIDs and get new ones
-        if (provided_ssids) {
-            free(provided_ssids);
-        }
-        provided_ssids = getenv("SSIDs");
-        if (!provided_ssids) {
-            syslog(LOG_ERR, "No SSIDs provided on reload\n");
-            return;
-        }
-        
-        // Reload SSIDs
-        if (parse_ssids(provided_ssids) != 0) {
-            syslog(LOG_ERR, "Failed to reload SSIDs configuration\n");
-            return;
-        }
-        
-        // Free old ports and get new ones
-        if (provided_ports) {
-            free(provided_ports);
-        }
-        provided_ports = getenv("PORTs");
-        if (!provided_ports) {
-            syslog(LOG_ERR, "No PORTs provided on reload\n");
-            return;
-        }
-        
-        // Close existing sockets and reopen with new config
-        if (ports) {
-            for (int i = 0; i < port_count; i++) {
-                if (ports[i].sock >= 0) {
-                    close(ports[i].sock);
+int parse_iwinfo_by_essid(struct iface_info *iface)
+{
+    char cmd[256];
+    FILE *fp;
+    char output[128];
+    char *line;
+
+    snprintf(cmd, sizeof(cmd), IWINFO_CMD, iface->essid, iface->frequency);
+
+    fp = popen(cmd, "r");
+    if (fp == NULL)
+    {
+        syslog(LOG_ERR, "Failed to execute command: %s\n", cmd);
+        return 1;
+    }
+
+    // Read the first line (interface name)
+    line = fgets(output, sizeof(output), fp);
+    if (line)
+    {
+        output[strcspn(output, "\n")] = '\0'; // Remove trailing newline
+        snprintf(iface->iface, LEN_IFACE + 1, output);
+    }
+    else
+    {
+        return 1;
+    }
+
+    // Read the second line (BSSID)
+    line = fgets(output, sizeof(output), fp);
+    if (line)
+    {
+        output[strcspn(output, "\n")] = '\0'; // Remove trailing newline
+        snprintf(iface->bssid, LEN_BSSID + 1, output);
+    }
+    else
+    {
+        return 1;
+    }
+
+    // Close the pipe
+    pclose(fp);
+    return 0;
+}
+
+void add_iface_info(const char *essid, const char *upstream, const char *freq, int serial)
+{
+    iface_map = realloc(iface_map, (iface_map_size + 1) * sizeof(struct iface_info));
+    if (!iface_map)
+    {
+        syslog(LOG_ERR, "Memory allocation failed\n");
+        exit(1);
+    }
+    struct iface_info *info = &iface_map[iface_map_size];
+    memset(info, 0, sizeof(struct iface_info));
+    // use snprintf to copy essid to info->essid
+    snprintf(info->essid, LEN_ESSID + 1, essid);
+    snprintf(info->upstream, LEN_IFACE + 1, upstream);
+    snprintf(info->frequency, 2, freq);
+    info->serial = serial;
+    iface_map_size++;
+}
+
+int parse_uci_config()
+{
+    struct uci_context *ctx = uci_alloc_context();
+    if (!ctx)
+    {
+        syslog(LOG_ERR, "Failed to allocate UCI context\n");
+        return 1;
+    }
+
+    struct uci_package *pkg = NULL;
+    if (uci_load(ctx, CONFIG_PATH, &pkg) != UCI_OK)
+    {
+        syslog(LOG_ERR, "Failed to load UCI config\n");
+        uci_free_context(ctx);
+        return 1;
+    }
+
+    int serial = 1;
+    struct uci_element *e;
+    uci_foreach_element(&pkg->sections, e)
+    {
+        struct uci_section *s = uci_to_section(e);
+        if (!strcmp(s->type, "network"))
+        {
+            const char *upstream = uci_lookup_option_string(ctx, s, "upstream");
+            if (!upstream)
+                continue;
+            syslog(LOG_INFO, "Processing ssids with upstream %s", upstream);
+            struct uci_option *opt, *opt2;
+
+            opt = uci_lookup_option(ctx, s, "freq");
+            if (opt && opt->type == UCI_TYPE_LIST)
+            {
+                struct uci_element *i;
+                char *freq_type = NULL;
+                uci_foreach_element(&opt->v.list, i)
+                {
+                    // parse 6G ifaces
+                    if (!strcmp(i->name, "6G"))
+                    {
+                        opt2 = uci_lookup_option(ctx, s, "ssid6G");
+                        freq_type = "6";
+                    }
+                    // parse 5G ifaces
+                    else if (!strcmp(i->name, "5G"))
+                    {
+                        opt2 = uci_lookup_option(ctx, s, "ssid5G");
+                        freq_type = "5";
+                    }
+                    // parse 2G ifaces
+                    else if (!strcmp(i->name, "2G"))
+                    {
+                        opt2 = uci_lookup_option(ctx, s, "ssid2G");
+                        freq_type = "2";
+                    }
+
+                    if (opt2 && opt2->type == UCI_TYPE_LIST)
+                    {
+                        struct uci_element *i;
+                        uci_foreach_element(&opt2->v.list, i)
+                        {
+                            add_iface_info(i->name, upstream, freq_type, serial++);
+                        }
+                    }
                 }
             }
-            free(ports);
-            ports = NULL;
-            port_count = 0;
-        }
-        
-        // Reload ports
-        if (parse_ports(provided_ports) != 0) {
-            syslog(LOG_ERR, "Failed to reload ports configuration\n");
-            return;
-        }
-        
-        // Reapply tc rules
-        if (setup_tc() == 0) {
-            syslog(LOG_INFO, "Reloaded with SSIDs: %s and Ports: %s\n",
-                   provided_ssids, provided_ports);
-        } else {
-            syslog(LOG_ERR, "Failed to reload tc configuration\n");
+
+            // initialize socket to upstream interface, say "up0v0"
+            port_map = realloc(port_map, (port_map_size + 1) * sizeof(struct port_info));
+            int sock = socket(AF_PACKET, SOCK_RAW, 0);
+            if (sock < 0)
+            {
+                syslog(LOG_ERR, "Failed to create socket for %s\n", upstream);
+                continue;
+            }
+
+            // Get interface index
+            int ifindex = if_nametoindex(upstream);
+            if (ifindex == 0)
+            {
+                syslog(LOG_ERR, "Failed to get ifindex for %s\n", upstream);
+                close(sock);
+            }
+
+            // Store in port_map
+            snprintf(port_map[port_map_size].name, LEN_IFACE + 1, upstream);
+            port_map[port_map_size].sock = sock;
+            port_map[port_map_size].ifindex = ifindex;
+            port_map_size++;
+            syslog(LOG_INFO, "Initialized socket for upstream interface %s", upstream);
         }
     }
+
+    uci_free_context(ctx);
+    return 0;
 }
 
-char *get_hostname() {
-    static char hostname[256];
-    if (gethostname(hostname, sizeof(hostname)) != 0) {
-        strcpy(hostname, "unknown");
-    }
-    return hostname;
-}
-
-struct iface_info *find_iface_info_by_vlan(int vlan_id) {
-    for (int i = 0; i < iface_count; i++) {
-        if (iface_map[i].serial == vlan_id) {
+struct iface_info *find_iface_info_by_vlan(int vlan_id)
+{
+    for (int i = 0; i < iface_map_size; i++)
+    {
+        if (iface_map[i].serial == vlan_id)
+        {
             return &iface_map[i];
         }
     }
@@ -391,13 +277,15 @@ struct iface_info *find_iface_info_by_vlan(int vlan_id) {
 }
 
 void process_packet(unsigned char *user, const struct pcap_pkthdr *header,
-                    const unsigned char *packet) {
+                    const unsigned char *packet)
+{
     int orig_len = header->len;
     struct ethhdr *eth = (struct ethhdr *)packet;
     int vlan_id = -1;
     int eth_offset = sizeof(struct ethhdr);
 
-    if (ntohs(eth->h_proto) != ETH_P_8021Q) {
+    if (ntohs(eth->h_proto) != ETH_P_8021Q)
+    {
         syslog(LOG_DEBUG,
                "No VLAN header found in packet (EtherType: 0x%04x)\n",
                ntohs(eth->h_proto));
@@ -409,11 +297,14 @@ void process_packet(unsigned char *user, const struct pcap_pkthdr *header,
     eth_offset += sizeof(struct vlan_hdr);
 
     struct iface_info *info = find_iface_info_by_vlan(vlan_id);
-    if (!info) {
+    if (!info)
+    {
         syslog(LOG_ERR, "No interface info found for VLAN ID %d\n", vlan_id);
         return;
     }
 
+    syslog(LOG_INFO, "Received dhcp packet with vlan id %d from iface %s of length: %d", vlan_id, info->iface, header->len);
+
     char *hostname = get_hostname();
     int circuit_id_len = strlen(info->bssid) + 1 + strlen(info->essid);
     int remote_id_len = strlen(hostname);
@@ -429,13 +320,16 @@ void process_packet(unsigned char *user, const struct pcap_pkthdr *header,
     int dhcp_len = ntohs(udp->len) - sizeof(struct udphdr);
 
     int options_end = -1;
-    for (int i = dhcp_len - 1; i >= 0; i--) {
-        if (dhcp_start[i] == 0xFF) { // End option
+    for (int i = dhcp_len - 1; i >= 0; i--)
+    {
+        if (dhcp_start[i] == 0xFF)
+        { // End option
             options_end = i;
             break;
         }
     }
-    if (options_end == -1) {
+    if (options_end == -1)
+    {
         syslog(LOG_DEBUG, "Could not find DHCP options end tag\n");
         return;
     }
@@ -445,7 +339,8 @@ void process_packet(unsigned char *user, const struct pcap_pkthdr *header,
     int orig_options_len = options_end;
     int new_len = orig_len - 4 - 1 + opt82_len + 1;
     unsigned char *new_packet = malloc(new_len);
-    if (!new_packet) {
+    if (!new_packet)
+    {
         syslog(LOG_ERR, "Failed to allocate memory for new packet\n");
         return;
     }
@@ -501,10 +396,12 @@ void process_packet(unsigned char *user, const struct pcap_pkthdr *header,
     new_ip->check = 0;
     unsigned int sum = 0;
     unsigned short *ip_ptr = (unsigned short *)new_ip;
-    for (int i = 0; i < ip->ihl * 2; i++) {
+    for (int i = 0; i < ip->ihl * 2; i++)
+    {
         sum += *ip_ptr++;
     }
-    while (sum >> 16) {
+    while (sum >> 16)
+    {
         sum = (sum & 0xFFFF) + (sum >> 16);
     }
     new_ip->check = ~sum;
@@ -524,13 +421,16 @@ void process_packet(unsigned char *user, const struct pcap_pkthdr *header,
     unsigned char *udp_start = (unsigned char *)new_udp;
     int udp_total_len = ntohs(new_udp->len);
     unsigned short *udp_ptr = (unsigned short *)udp_start;
-    for (int i = 0; i < udp_total_len / 2; i++) {
+    for (int i = 0; i < udp_total_len / 2; i++)
+    {
         sum += *udp_ptr++;
     }
-    if (udp_total_len % 2) {
+    if (udp_total_len % 2)
+    {
         sum += *(unsigned char *)udp_ptr;
     }
-    while (sum >> 16) {
+    while (sum >> 16)
+    {
         sum = (sum & 0xFFFF) + (sum >> 16);
     }
     new_udp->check = ~sum;
@@ -542,92 +442,91 @@ void process_packet(unsigned char *user, const struct pcap_pkthdr *header,
     socket_address.sll_family = AF_PACKET;
     socket_address.sll_protocol = htons(ETH_P_ALL);
 
-    for (int i = 0; i < port_count; i++) {
-        socket_address.sll_ifindex = ports[i].ifindex;
-        
-        if (sendto(ports[i].sock, new_packet, new_len, 0,
-                  (struct sockaddr *)&socket_address,
-                  sizeof(socket_address)) < 0) {
-            syslog(LOG_ERR, "Failed to send packet to %s: %s\n",
-                   ports[i].name, strerror(errno));
-        } else {
-            syslog(LOG_DEBUG,
-                   "Successfully forwarded packet to %s (new length: %d)\n",
-                   ports[i].name, new_len);
+    for (int i = 0; i < port_map_size; i++)
+    {
+        if (!strcmp(info->upstream, port_map[i].name))
+        {
+            socket_address.sll_ifindex = port_map[i].ifindex;
+            if (sendto(port_map[i].sock, new_packet, new_len, 0, (struct sockaddr *)&socket_address,
+                       sizeof(socket_address)) < 0)
+            {
+                syslog(LOG_ERR, "Failed to send packet to %s: %s\n",
+                       info->upstream, strerror(errno));
+            }
+            else
+            {
+                syslog(LOG_INFO,
+                       "Successfully forwarded packet to %s (new length: %d)\n",
+                       info->upstream, new_len);
+            }
+            break;
         }
     }
 
     free(new_packet);
 }
 
-int main(int argc, char *argv[]) {
+void signal_handler(int sig)
+{
+    switch (sig)
+    {
+    case SIGTERM:
+    case SIGHUP:
+        cleanup();
+        break;
+    default:
+        break;
+    }
+}
+
+int main(int argc, char *argv[])
+{
     openlog("dhcp_inject:", LOG_PID | LOG_CONS, LOG_DAEMON);
 
     signal(SIGTERM, signal_handler);
     signal(SIGHUP, signal_handler);
 
-    // Read IFACEs from environment variable
-    char *iface_env = getenv("IFACEs");
-    if (!iface_env) {
-        syslog(LOG_ERR, "No IFACEs provided. Exiting...\n");
-        cleanup();
-        return 1;
-    }
-    total_iface = atoi(iface_env);
-    if (total_iface <= 0) {
-        syslog(LOG_ERR, "Invalid IFACEs value: %s. Exiting...\n", iface_env);
+    if (parse_uci_config() != 0)
+    {
+        syslog(LOG_ERR, "Failed to parse UCI configuration\n");
         cleanup();
         return 1;
     }
 
-    provided_ssids = getenv("SSIDs");
-    syslog(LOG_INFO, "Provided SSIDs: %s\n", provided_ssids);
-    if (!provided_ssids && argc > 1) {
-        provided_ssids = strdup(argv[1]);
-    }
-    if (!provided_ssids) {
-        syslog(LOG_ERR, "No SSIDs provided. Exiting...\n");
-        return 1;
+    for (int i = 0; i < iface_map_size; i++)
+    {
+        if (parse_iwinfo_by_essid(&iface_map[i]) != 0)
+        {
+            syslog(LOG_ERR, "Failed to get iface info for ESSID: %s\n", iface_map[i].essid);
+            cleanup();
+            return 1;
+        }
+        else
+        {
+            syslog(LOG_INFO, "iface_info[%d]: iface='%s', freq='%s', essid='%s', bssid='%s', upstream='%s', serial=%d\n",
+                   i, iface_map[i].iface, iface_map[i].frequency, iface_map[i].essid, iface_map[i].bssid,
+                   iface_map[i].upstream, iface_map[i].serial);
+        }
     }
 
-    provided_ports = getenv("PORTs");
-    syslog(LOG_INFO, "Provided PORTs: %s\n", provided_ports);
-    if (!provided_ports) {
-        syslog(LOG_ERR, "No PORTs provided. Exiting...\n");
-        cleanup();
-        return 1;
-    }
-
-    if (parse_ssids(provided_ssids) != 0) {
-        syslog(LOG_ERR, "Failed to parse SSIDs\n");
-        cleanup();
-        return 1;
-    }
-
-    if (parse_ports(provided_ports) != 0) {
-        syslog(LOG_ERR, "Failed to parse ports\n");
-        cleanup();
-        return 1;
-    }
-
-    if (setup_tc() != 0) {
+    if (setup_tc() != 0)
+    {
         syslog(LOG_ERR, "Setup failed\n");
         cleanup();
         return 1;
     }
 
-    syslog(LOG_INFO, "Setup complete for SSIDs: %s and Ports: %s\n",
-           provided_ssids, provided_ports);
-
     char errbuf[PCAP_ERRBUF_SIZE];
     handle = pcap_open_live("ifb-inject", BUFSIZ, 1, 1000, errbuf);
-    if (handle == NULL) {
+    if (handle == NULL)
+    {
         syslog(LOG_ERR, "Couldn't open device ifb-inject: %s\n", errbuf);
         cleanup();
         return 1;
     }
 
-    if (pcap_loop(handle, -1, process_packet, NULL) < 0) {
+    if (pcap_loop(handle, -1, process_packet, NULL) < 0)
+    {
         syslog(LOG_ERR, "pcap_loop failed: %s\n", pcap_geterr(handle));
         cleanup();
         return 1;

feeds/ucentral/udhcpinject/src/udhcpinject.h

@@ -1,9 +1,27 @@
 #include <stdint.h>
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
 #include <netinet/in.h>
 
 #define LEN_ESSID 32
 #define LEN_BSSID 12
 #define LEN_IFACE 15
+#define LEN_FREQ 3
+
+#define MAX_INTERFACES 48
+#define MAX_PORTS 8
+
+#define CONFIG_PATH "/etc/config/dhcpinject"
+
+#define IWINFO_CMD "iwinfo | grep %s -A2 | grep '.*Channel:.*\\(%s\\..*\\) GHz' -B2 | awk '/ESSID/{print $1} /Access Point/{gsub(/:/, \"\", $3); print $3}'"
+
+static pcap_t 		*handle = NULL;
+
+static int 			 iface_map_size = 0;
+struct iface_info 	*iface_map = NULL;
+static int 			 port_map_size = 0;
+struct port_info 	*port_map = NULL;
 
 // DHCP header structure
 struct dhcp_packet {
@@ -25,11 +43,15 @@ struct dhcp_packet {
 	uint8_t options[];
 };
 
+// up4094v4094
+
 // Structure to hold interface info
 struct iface_info {
     char iface[LEN_IFACE + 1];
     char essid[LEN_ESSID + 1];
     char bssid[LEN_BSSID + 1];
+	char upstream[LEN_IFACE + 1];
+	char frequency[4];
     int serial;
 };
 
@@ -41,6 +63,14 @@ struct port_info {
 
 // VLAN header structure
 struct vlan_hdr {
-    __be16 h_vlan_TCI;              // VLAN Tag Control Information
+    __be16 h_vlan_TCI;                // VLAN Tag Control Information
     __be16 h_vlan_encapsulated_proto; // Encapsulated protocol
 };
+
+char *get_hostname() {
+    static char hostname[256];
+    if (gethostname(hostname, sizeof(hostname)) != 0) {
+        strcpy(hostname, "unknown");
+    }
+    return hostname;
+}

patches/0100-sonicfi_rap63xc-211g-enable-pstore.patch

@@ -0,0 +1,38 @@
+From adbd8be88f9c5af3f79dc106bc0f2ace5eb50768 Mon Sep 17 00:00:00 2001
+From: jackcybertan <jack.tsai@cybertan.com.tw>
+Date: Thu, 21 Aug 2025 15:22:51 +0800
+Subject: [PATCH] sonicfi_rap63xc-211g: enable pstore
+
+Signed-off-by: jackcybertan <jack.tsai@cybertan.com.tw>
+---
+ .../ramips/dts/mt7621_sonicfi_rap63xc-211g.dts     | 14 ++++++++++++++
+ 1 file changed, 14 insertions(+)
+
+diff --git a/target/linux/ramips/dts/mt7621_sonicfi_rap63xc-211g.dts b/target/linux/ramips/dts/mt7621_sonicfi_rap63xc-211g.dts
+index b64ca5708b..d076d682c9 100755
+--- a/target/linux/ramips/dts/mt7621_sonicfi_rap63xc-211g.dts
++++ b/target/linux/ramips/dts/mt7621_sonicfi_rap63xc-211g.dts
+@@ -79,6 +79,20 @@
+ 			linux,code = <KEY_RESTART>;
+ 		};
+ 	};
++
++	reserved-memory {
++		#address-cells = <1>;
++		#size-cells = <1>;
++		ranges;
++
++		ramoops: ramoops@ff80000 {
++			 compatible = "ramoops";
++			 reg = <0x0ff80000 0x80000>;
++			 record-size = <0x20000>;
++			 console-size = <0x20000>;
++			 pmsg-size = <0x20000>;
++		 };
++	};
+ };
+ 
+ &spi0 {
+-- 
+2.34.1
+

patches/0101-ipq53xx-add-KERNEL_IPQ_MEM_PROFILE.patch

@@ -0,0 +1,25 @@
+From 40894005e2c114664a44abb0ffadb1cb945a88e2 Mon Sep 17 00:00:00 2001
+From: Antonio Wu <antonio.wu@cybertan.com.tw>
+Date: Mon, 4 Aug 2025 05:10:41 +0000
+Subject: [PATCH] add KERNEL_IPQ_MEM_PROFILE for IPQ53XX 
+
+---
+ config/Config-kernel.in | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+diff --git a/config/Config-kernel.in b/config/Config-kernel.in
+index 3529696559..b7f13eccbe 100644
+--- a/config/Config-kernel.in
++++ b/config/Config-kernel.in
+@@ -6,7 +6,7 @@ config KERNEL_IPQ_MEM_PROFILE
+ 	int "Different memory profile "
+ 	range 0 1024
+ 	default 512
+-	depends on TARGET_ipq807x || TARGET_ipq60xx || TARGET_ipq50xx || TARGET_ipq95xx
++	depends on TARGET_ipq807x || TARGET_ipq60xx || TARGET_ipq50xx || TARGET_ipq95xx || TARGET_ipq53xx
+ 	help
+ 	  This option select memory profile to be used,which defines
+ 	  the reserved memory configuration used in device tree.
+-- 
+2.17.1
+

patches/0101-support-dhcp-opt138-opt224.patch

@@ -0,0 +1,68 @@
+From ba5c63cc0cbbacd952a5c2cfd873439bf5adc86a Mon Sep 17 00:00:00 2001
+From: Tanya Singh <tanya_singh@accton.com>
+Date: Thu, 18 Sep 2025 13:21:38 +0800
+Subject: [PATCH] netifd: Support DHCP option 138 and DHCP option 224
+
+---
+ .../netifd/files/lib/netifd/dhcp.script       | 10 ++++++++++
+ .../patches/601-dhcp_opt138_opt224.patch      | 20 +++++++++++++++++++
+ 2 files changed, 30 insertions(+)
+ create mode 100644 package/utils/busybox/patches/601-dhcp_opt138_opt224.patch
+
+diff --git a/package/network/config/netifd/files/lib/netifd/dhcp.script b/package/network/config/netifd/files/lib/netifd/dhcp.script
+index 6fcf139beb..9c4366f48b 100755
+--- a/package/network/config/netifd/files/lib/netifd/dhcp.script
++++ b/package/network/config/netifd/files/lib/netifd/dhcp.script
+@@ -4,6 +4,8 @@
+ . /lib/functions.sh
+ . /lib/netifd/netifd-proto.sh
+ 
++rm -rf /tmp/dhcp-option-*
++
+ set_classless_routes() {
+ 	local max=128
+ 	while [ -n "$1" -a -n "$2" -a $max -gt 0 ]; do
+@@ -111,6 +113,14 @@ case "$1" in
+ 	;;
+ esac
+ 
++if [ -n "${opt138}" ]; then
++	echo -n "${opt138}" > /tmp/dhcp-option-138
++fi
++
++if [ -n "${opt224}" ]; then
++	echo -n "${opt224}" > /tmp/dhcp-option-224
++fi
++
+ # user rules
+ [ -f /etc/udhcpc.user ] && . /etc/udhcpc.user "$@"
+ for f in /etc/udhcpc.user.d/*; do
+diff --git a/package/utils/busybox/patches/601-dhcp_opt138_opt224.patch b/package/utils/busybox/patches/601-dhcp_opt138_opt224.patch
+new file mode 100644
+index 0000000000..38e53be78c
+--- /dev/null
++++ b/package/utils/busybox/patches/601-dhcp_opt138_opt224.patch
+@@ -0,0 +1,20 @@
++--- a/networking/udhcp/common.c	2025-09-18 13:15:38.313248300 +0800
+++++ b/networking/udhcp/common.c	2025-09-18 13:17:50.078418978 +0800
++@@ -55,6 +55,8 @@ const struct dhcp_optflag dhcp_optflags[
++ 	{ OPTION_STRING                           , 0x43 }, /* DHCP_BOOT_FILE     */
++ //TODO: not a string, but a set of LASCII strings:
++ //	{ OPTION_STRING                           , 0x4D }, /* DHCP_USER_CLASS    */
+++	{ OPTION_IP								  , 0x8A }, /* DHCP_OPT138        */
+++	{ OPTION_STRING		          			  , 0xE0 }, /* DHCP_OPT224        */
++ 	{ OPTION_STRING                           , 0x64 }, /* DHCP_PCODE         */
++ 	{ OPTION_STRING                           , 0x65 }, /* DHCP_TCODE         */
++ #if ENABLE_FEATURE_UDHCP_RFC3397
++@@ -124,6 +126,8 @@ const char dhcp_option_strings[] ALIGN1
++ 	"tftp" "\0"             /* DHCP_TFTP_SERVER_NAME*/
++ 	"bootfile" "\0"         /* DHCP_BOOT_FILE       */
++ //	"userclass" "\0"        /* DHCP_USER_CLASS      */
+++	"opt138" "\0"           /* DHCP_OPT138          */
+++	"opt224" "\0"           /* DHCP_OPT224          */
++ 	"tzstr" "\0"            /* DHCP_PCODE           */
++ 	"tzdbstr" "\0"          /* DHCP_TCODE           */
++ #if ENABLE_FEATURE_UDHCP_RFC3397
+-- 
+2.34.1
+

profiles/indio_um-325ax-v2.yml

@@ -0,0 +1,19 @@
+---
+profile: indio_um-325ax-v2
+target: ipq50xx
+subtarget: generic
+description: Build image for the Indio um-325ax-v2
+image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-indio_um-325ax-v2-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x_v5.4
+include:
+  - ucentral-ap
+packages:
+  - ipq50xx
+diffconfig: |
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=512
+  CONFIG_BUSYBOX_CUSTOM=y
+  CONFIG_BUSYBOX_CONFIG_STTY=y
+  
+  

profiles/indio_um-525axp.yml

@@ -0,0 +1,19 @@
+---
+profile: indio_um-525axp
+target: ipq50xx
+subtarget: generic
+description: Build image for the Indio um-525axp
+image: bin/targets/ipq50xx/generic/openwrt-ipq50xx-indio_um-525axp-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x_v5.4
+include:
+  - ucentral-ap
+packages:
+  - ipq50xx
+diffconfig: |
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=512
+  CONFIG_BUSYBOX_CUSTOM=y
+  CONFIG_BUSYBOX_CONFIG_STTY=y
+  
+  

profiles/zyxel_nwa50be.yml

@@ -0,0 +1,16 @@
+---
+profile: zyxel_nwa50be
+target: ipq53xx
+subtarget: generic
+description: Build image for the zyxel nwa50be
+image: bin/targets/ipq53xx/generic/openwrt-ipq53xx-zyxel_nwa50be-squashfs-sysupgrade.tar
+feeds:
+  - name: qca
+    path: ../../feeds/qca-wifi-7
+packages:
+  - ipq53xx
+  - qca-ssdk-shell
+include:
+  - ucentral-ap
+diffconfig: |
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=0