- We have more flash space to use with nds32 toolchain GCC6.3.0,
so we enable a few console commands that were disabled previously.
And we also enable LTO to reduce the size of FW image.
- Put "__wait_evt" function into ram_code section to
fill the gap of flash and improving performance of code-fetch.
BUG=none
BRANCH=none
TEST=boot to kernel on reef_it8320.
Change-Id: I3b745ff80a57ef1163794864c39c22f7e1f86634
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-on: https://chromium-review.googlesource.com/788712
Commit-Ready: ChromeOS CL Exonerator Bot <chromiumos-cl-exonerator@appspot.gserviceaccount.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Until HOOK_INIT has completed, do not allow any tasks other than HOOKS
or IDLE to be scheduled. Programmers often make the assumption that
a HOOK_INIT function is guaranteed to be run before task code that depends
on it, so let's make it so.
BUG=chromium:649398
BRANCH=None
TEST=Manual on kevin, compare boot without patch:
...
[0.004 power state 0 = G3, in 0x0008] <-- from chipset task
RTC: 0x00000000 (0.00 s)
[0.004 power state 4 = G3->S5, in 0x0008]
RTC: 0x00000000 (0.00 s)
[0.005 clear MKBP fifo]
[0.006 clear MKBP fifo]
[0.006 KB init state: ... <-- from keyscan task
[0.012 SW 0x05]
[0.155 hash start 0x00020000 0x00019a38]
[0.158 HOOK_INIT DONE!]
... to boot with patch:
...
RTC: 0x58cc614c (1489789260.00 s)
[0.004 clear MKBP fifo]
[0.005 clear MKBP fifo]
[0.010 SW 0x05]
[0.155 hash start 0x00020000 0x000198e0]
[0.157 HOOK_INIT DONE!]
...
Also, verify kevin boots to OS and is generally functional through
sysjump and basic tasks, and verify elm (stm32f0 / cortex-m0) boots.
Change-Id: If56fab05ce9b9650feb93c5cfc2d084aa281e622
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/456628
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Because N8 CPU doesn't have floating point unit,
so we implement an extra floating point engine
(single-precision addition, subtraction, multiplication,
and division) into it8320 to improve performance of
floating point operation.
To make CPU's instruction compatible, we use register (DLMB)
to switch ALU (Arithmetic Logic Unit). eg:
Instruction 'ADD45' adds the contents of two registers then
writes the result to the source register.
But if we switch ALU to floating point operation mode,
this instruction will do a floating-point addition instead.
For the other FPU that we don't support as far,
we have to use soft float library routines of nds32.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=add the following console command and test different
scenarios by changing variable a and b.
#define PRINTF_FLOAT(x) ((int)((x) * 1000.0f))
static int it83xx_fpu_test(int argc, char **argv)
{
volatile float a = 1.23f;
volatile float b = 4.56f;
volatile float c;
c = a + b;
ccprintf("__addsf3: (%d)\n", PRINTF_FLOAT(c));
c = a - b;
ccprintf("__subsf3: (%d)\n", PRINTF_FLOAT(c));
c = a * b;
ccprintf("__mulsf3: (%d)\n", PRINTF_FLOAT(c));
c = a / b;
ccprintf("__divsf3: (%d)\n", PRINTF_FLOAT(c));
return EC_SUCCESS;
}
DECLARE_CONSOLE_COMMAND(fpu, it83xx_fpu_test, "", "");
Change-Id: I4fc1c08d8c2376156bec9f098491187675c4a88f
Reviewed-on: https://chromium-review.googlesource.com/427640
Commit-Ready: Dino Li <Dino.Li@ite.com.tw>
Tested-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
- Before the change was made, the "__ro_end" was at 00013520h.
We change to 00012760h.
- Rename "CONFIG_IT83XX_ILM_BLOCK_SIZE" to "IT83XX_ILM_BLOCK_SIZE"
this is because we don't support reconfiguration at board-level.
- Put some task functions into "__ram_code" section to
fill the gap and improving performance of code-fetch.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=console commands: flasherase, flashwrite, and flashread.
Change-Id: I2f2906a2a0b6971aadd00120c282801161447808
Reviewed-on: https://chromium-review.googlesource.com/424248
Commit-Ready: Dino Li <Dino.Li@ite.com.tw>
Tested-by: Dino Li <Dino.Li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
In __wait_evt(), if a timer expiration occurs after we read event
status, before the timer is canceled, then TASK_EVENT_TIMER will be
propagated to the next task wait, likely leading to premature timeout.
Prevent this by clearing TASK_EVENT_TIMER after canceling our timer.
BUG=chrome-os-partner:58658
BRANCH=gru
TEST=Manual on gru, run 'pd # hard' for 12 hours with charger attached,
verify no TCPC I2C read errors occur.
Change-Id: Iac2f05a768b4ef29f82e7c3eb899f4c7dd5c3744
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/400968
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Since pretty much always, we've declared console commands to take
a "longhelp" argument with detailed explanations of what the
command does. But since almost as long, we've never actually used
that argument for anything - we just silently throw it away in
the macro. There's only one command (usbchargemode) that even
thinks it defines that argument.
We're never going to use this, let's just get rid of it.
BUG=none
BRANCH=none
CQ-DEPEND=CL:*279060
CQ-DEPEND=CL:*279158
CQ-DEPEND=CL:*279037
TEST=make buildall; tested on Cr50 hardware
Everything builds. Since we never used this arg anyway, there had
better not be any difference in the result.
Change-Id: Id3f71a53d02e3dc625cfcc12aa71ecb50e35eb9f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/374163
Reviewed-by: Myles Watson <mylesgw@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
LPC access interrupt only enabled when EC entering deep doze mode. This
will reduce interrupt of LPC access. Also, this interrupt is always
enabled for LPC platform to support "CONFIG_LOW_POWER_S0".
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=Tested ectool command 'version' x 10000.
Change-Id: I9053c4018b38a8a852c3c6254e1fcde625f3fa3a
Reviewed-on: https://chromium-review.googlesource.com/336112
Commit-Ready: Dino Li <dino0303@gmail.com>
Tested-by: Dino Li <dino0303@gmail.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
We have a limitation for EC interrupt vector registers.
System may read incorrect interrupt number in ISR so we need to add
a workaround to prevent it.
The following is a example that got incorrect interrupt number:
1. REG IVCTx = 0x10. (no interrupt pending)
2. EC INT6 interrupt occurs (IVCTx = 0x16) and jump to ISR.
3. Read interrupt vector register to determine interrupt number.
4. Higher priority interrupt of same interrupt group occurs
(for example: INT134, IVCTx = 0x96) while the system is reading the
interrupt vector register for EC INT6, we may end up with an incorrect
interrupt number between 0x16 and 0x96.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. EC interrupts work normally: WUI (GPIO interrupt), timer, uart,
LPC, I2C, and PECI.
2. Console command 'taskinfo'.
Change-Id: I54e61f417ad506eb3b4cd5d0652f64eed9a28a17
Reviewed-on: https://chromium-review.googlesource.com/322097
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
[task]
1. Copy task_wait_event_mask() function of cortex-m0.
[system]
2. Include host_command.h for host_command_pd_request_hibernate().
[i2c]
3. Update i2c handler to use task_wait_event_mask.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=chromium:435611,chromium:435612
TEST=1. console commands: i2cscan, i2cxfer, and battery.
Change-Id: If5bb4407460d28c0b021ab133ca4b635ff7bc3c9
Reviewed-on: https://chromium-review.googlesource.com/320440
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
[symptom]
The 'vboot_hash_start()' always return busy error and variable 'in_progress'
got a strange value(should be 0 or 1).
'start_irq_handler()' causes scratchpad overflow in first context switch.
It must be called after SP switch to system stack in ISR.
NOTE:
The scratchpad is still also need more size even if
'start_irq_handler()' is using system stack. following is detail:
1. uint32_t scratchpad[19] 0x81d34 ~ 0x81d7f
[__task_start:]
2. /* put the dummy stack pointer at the top of the stack in scratchpad */
addi $sp, $r3, 4 * 18
-> SP 0x81d7c
3. syscall push return address (-4)
-> SP 0x81d78
[ISR:]
4. push r15, fp, lp, and sp (-0x10)
-> SP 0x81d68
5. push r0 ~ r5 (-0x18)
-> SP 0x81d50
[__switch_task:]
6. /* save ipsw, ipc, r6, r7, r8, r9, r10 on the current process stack */ (-0x1C)
-> SP 0x81d34
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. hash done.
2. console command 'taskinfo'.
3. the scratchpad does not overflow after first context switch.
Change-Id: If5d89ff5c945a777010492fcfb54bf41f434ed69
Reviewed-on: https://chromium-review.googlesource.com/317468
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
1. In combinational mode and clock source is 8MHz,
if timer 3 counter register always equals to 7, then timer 4 will be a
32-bit MHz free-running counter.
2. Fix TIMER_32P768K_CNT_TO_US(), each count should be 30.5175 us,
not 32.768us.
3. Fix TIMER_CNT_8M_32P768K().
4. Make sure LPC wake up interrupt is enabled before entering doze /
deep doze mode.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. Console commands: 'gettime', 'timerinfo', 'waitms', and 'forcetime'.
2. Enabled Hook debug, no warning message received (48hrs).
3. Tested ectool command 'version' x 2000.
Change-Id: I796d985361d3c18bc5813c58705b41923e28c5b1
Reviewed-on: https://chromium-review.googlesource.com/310039
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
1. To enable INT_PRI (hardware interrupt priority level 0~3)
register, bit0@INT_CTRL = 0.
2. GIE need to be enabled before UART is initialized.
[symptom]
To define CONFIG_RWSIG / CONFIG_RSA / CONFIG_SHA256, then power on:
after RW image is verified, firmware stuck in uart_flush_output().
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. bit0@INT_CTRL = 0.
2. The RW image is verified and jump to image RW.
Change-Id: I393a3d5f87ea257885b872c91bfce43aecbaea8b
Reviewed-on: https://chromium-review.googlesource.com/309400
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
1. Implement deep doze mode for CONFIG_LOW_POWER_IDLE.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=test the following items in deep doze mode.
1. WUI interrupts wake-up OK. (For example, power button, lid,
uart rx, keyboard ksi, and so on)
2. LPC access interrupt wake-up OK.
3. Enabled Hook debug, no warning message received (48hrs).
Change-Id: I8702a112632cb6c1c0fa75d682badf272130a7d4
Reviewed-on: https://chromium-review.googlesource.com/307060
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
[chip config]
1. No hardware specific udelay().
2. Enable watchdog.
[watchdog]
3. Watchdog period is "CONFIG_WATCHDOG_PERIOD_MS" of config.h.
4. Watchdog auxiliary timer period is "CONFIG_AUX_TIMER_PERIOD_MS".
[task and irq]
5. Write 1 to clear interrupt pending status, no |.
6. A global variable for store interrupt number of software interrupt.
[uart]
7. Always reset UART module before config it.
[hwtimer]
8. Use more external timers for HW timer module.
[task]
9. Fix task profiling.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=[watchdog]
1. console "waitms 1100", only pre-watchdog warning message.
2. console "waitms 1600", warning message and watchdog reset.
[hwtimer]
3. console commands "gettime", "timerinfo", and "forcetime".
4. enable hook debug and there is no delayed by more than 10%
warning message over 48 hours.
5. There is no watchdog reset too.
[task]
6. console 'taskinfo'
Task Ready Name Events Time (s) StkUsed
0 R << idle >> 00000000 32.927724 308/512
1 HOOKS 00000000 0.034267 372/768
2 R CONSOLE 00000000 0.116763 468/768
3 HOSTCMD 00000000 0.000641 372/512
4 KEYPROTO 00000000 0.000042 212/512
5 KEYSCAN 00000000 0.000908 356/512
IRQ counts by type:
38 2932
155 1
158 261
160 67
Service calls: 87
Total exceptions: 3348
Task switches: 167
Task switching started: 0.001999 s
Time in tasks: 33.282819 s
Time in exceptions: 0.164717 s
Change-Id: I234085cec231cd855d2a5e639ea1b0966c61d796
Reviewed-on: https://chromium-review.googlesource.com/296939
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Returns the most significant bit set.
Replace 31 - __builtin_clz(x), so x must be different from 0.
Use get_next_bit when not on the performance path,
on performance path set the bit field just after reading it.
BRANCH=smaug
BUG=none
TEST=compile, check Ryu still works.
Change-Id: Ie1a4cda4188f45b4bf92d0549d5c8fb401a30e5d
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/301300
When there is an interrupt event, N8 CPU will save PSW register to IPSW
register and clear GIE then jump to interrupt service routine. N8 will
restore PSW from IPSW after "iret" instruction (the above are purely
hardware mechanism).
Nested interrupt will occur if we set GIE again in interrupt context.
symptom:
power button pressed while LID open -> exception or unknown reset.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. Manually pressed power button x200.
2. Console "eflash" erase and write eflash OK.
Change-Id: Ic04a23d473ebc6417dffea814a27583cb8d63a1f
Reviewed-on: https://chromium-review.googlesource.com/289437
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
This commit changes the way in which tasks are started. Instead of
having all tasks marked as ready to run upon initialization, only the
hooks task is marked as ready to run. HOOK_INITs are now run at the
beginning of the hooks task. After the HOOK_INITs, the hooks task calls
back to enable the rest of the tasks, reschedules, and proceeds as
usual. This also allows the removal of checks for task_start_called().
BUG=chrome-os-partner:27226
BRANCH=None
TEST=Built and flash EC image for samus and verified that EC boot was
successful as well as AP boot. Additionally, verified that charging,
keyboard, tap-for-battery were all still functional.
TEST=make -j buildall tests
Change-Id: Iea53670222c803c2985e9c86c96974386888a4fe
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/283657
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
If task_get_current() is called early during initialization when we have
not yet done a context switch, our current_task pointer is invalid. Add
an assert to detect this case and put it behind CONFIG_DEBUG_BRINGUP, a
new config that's intended to enable possibly-costly pre-production
debugging.
BUG=chrome-os-partner:40677
TEST=Manual on glados. Define CONFIG_DEBUG_BRINGUP, then call i2c_write from
board_init and verify the new assert fails. Remove the i2c_write and verify
the new assert passes.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I6014ccf739dcc4c8f4f960be2b89f01e423b65b5
Reviewed-on: https://chromium-review.googlesource.com/273541
Reviewed-by: Randall Spangler <rspangler@chromium.org>
When another task is holding the lock, mutex_lock() should call
task_wait_event_mask() to wait only for TASK_EVENT_MUTEX events.
If it calls task_wait_event(), any pending events are silently
discarded while its waiting for the the lock.
BUG=chromium:435611
BRANCH=ToT,samus
TEST=make buildall -j, and:
Before this change, I watched the EC console while shutting down
and rebooting Samus. I saw the request event arrive:
[37.576295 LB lightbar_resume() requests 5 S3S0]
[46.055725 LB_version]
But the lightbar task never saw it. Adding a bunch of debug
messages showed that it was being lost in mutex_lock().
After this change, the event is delivered:
[30.167670 LB lightbar_resume() requests 5 S3S0]
[30.171009 LB cur_seq 2 S3 returned pending msg 5 S3S0]
[30.173816 LB running cur_seq 5 S3S0. prev_seq 2 S3]
[32.410073 LB cur_seq 5 S3S0 returned value 0]
[32.410865 LB running cur_seq 3 S0. prev_seq 2 S3]
[39.938388 LB_version]
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Change-Id: I011838538960cc57171f0a3c4cdee113d156e9ff
Reviewed-on: https://chromium-review.googlesource.com/231370
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Our code base contains a lot of debug messages in this pattern:
CPRINTF("[%T xxx]\n") or ccprintf("[%T xxx]\n")
The strings are taking up spaces in the EC binaries, so let's refactor
this by adding cprints() and ccprints().
cprints() is just like cprintf(), except that it adds the brackets
and the timestamp. ccprints() is equivalent to cprints(CC_CONSOLE, ...)
This saves us hundreds of bytes in EC binaries.
BUG=chromium:374575
TEST=Build and check flash size
BRANCH=None
Change-Id: Ifafe8dc1b80e698b28ed42b70518c7917b49ee51
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/200490
Reviewed-by: Randall Spangler <rspangler@chromium.org>
