It will be used by all variants of Rambi, so #ifdef BOARD_RAMBI is too
restrictive.
BUG=chrome-os-partner:24864
BRANCH=rambi
TEST=boot rambi 1.5 board; plug in USB mouse
Change-Id: I0ff02077388a6c6621c5746a693dde894cf8ad77
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/181682
Reviewed-by: Alec Berg <alecaberg@chromium.org>
BUG=chrome-os-partner:24455
BRANCH=none
TEST=Manual: Verify that CONIFG_PECI_TJMAX set per-board matches
the value queried over the PECI bus with the restricted
"peciprobe" command.
Change-Id: I8e99a23a66f26d6101e01cc751d0a8ca79686321
Signed-off-by: Dave Parker <dparker@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179682
Reviewed-by: Alec Berg <alecaberg@chromium.org>
This allows local and remote temp values to be added
to a board's list of temp sensors. It also adds a
'tmp432' EC console command to query temps
and set alert thresholds. Fractional degrees are not
supported. DPTF support is not addressed.
BUG=chrome-os-partner:23985
BRANCH=none
TEST=Add tmp432 support to a board with the sensor
then run the 'tmp432' and 'temps' EC console commands.
Signed-off-by: Dave Parker <dparker@chromium.org>
Change-Id: Ifee47cf4d4cf5eedef9ef2bfa2149f183f1d7a7b
Reviewed-on: https://chromium-review.googlesource.com/178688
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Dave Parker <dparker@chromium.org>
Tested-by: Dave Parker <dparker@chromium.org>
Move the non-core dependent code out of core/$(CORE) directory to
common/ directory.
Put all panic printing code in common/panic_output.c
Put timer management code in common/timer.c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:23574
TEST=./util/make_all.sh
use "crash divzero" and "panicinfo" on Link.
Change-Id: Ia4e1ebc74cd53da55fe24f69e96f39f512b9336d
Reviewed-on: https://chromium-review.googlesource.com/178871
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Jeremy Thorpe <jeremyt@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
These boards are unloved and unsupported. They'll never grow up to be
laptops, and hardware is increasingly hard to come by.
Comparable functionality is available in the other, more-loved boards.
Removing these boards speeds up util/make_all.sh by 40%. (If you're
not running that before every upload, you should be...)
BUG=chrome-os-partner:24062
BRANCH=none
TEST=build all remaining platforms and pass unit tests
Change-Id: I4d8a49e4d52d7393471f1b1cbef059c8db4a4f77
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177373
On certain boards it's no feasible to use the SERIRQ
method for generating the kebyboard interrupt. To that
end provide CONFIG_KEYBOARD_IRQ_GPIO option which
specifies the negative edge-triggered gpio for the
keyaboard interrupt.
BUG=chrome-os-partner:23965
BRANCH=None
TEST=Built and booted rambi using this option. Keyboard
works in kernel with interrupts for i8042 device.
Change-Id: I64f7e9530841c184d2a33821126ec446c96bb0f0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177188
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The LPC module has a dedicated control for SCI#.
However, certain situations require a dedicated
GPIO for asserting the SCI# signal.
Introduce CONFIG_SCI_GPIO to meet this requirement.
BUG=chrome-os-partner:24003
BRANCH=None
TEST=Built and booted rambi with dependency change. 'lidclose' and
'lidopen' cause ACPI interrupts.
Change-Id: I34c5f0ba5ff60151972921f251c71d3769a9ef8b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176804
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This adds the driver and a console command to read an Intersil ISL29305
light sensor connected to the EC.
BUG=chrome-os-partner:23380
BRANCH=samus
TEST=manual
Run the "als" command from the EC console, while pointing the sensor in
various directions. It should give higher numbers when facing a light
source. If you get "Error 1", it means the ALS isn't powered.
Change-Id: I855ed64dab7fc60e29126ab3e97669be24dc6a64
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176056
Changes somewhere in the recent past have caused I2C operations to
consume more stack space. The current failure mode is that after some
debug command or infrequent battery operation, the system fails.
Clean up and enable stack overflow detection by default, and add a
debug command (disabled by default) to verify overflow detection
works.
This adds several instructions to each context switch, but it's still
fairly inexpensive, and represents only a few percent increase in the
size of svc_handler(). That's better than silent failures.
BUG=chrome-os-partner:23938
BRANCH=none
TEST=Enable CONFIG_CMD_STACKOVERFLOW, then run the 'stackoverflow' command.
This should cause a stack overflow to be detected in the CONSOLE task.
Change-Id: I9303aee5bd9318f1d92838b399d15fb8f6a2bbf9
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176113
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Temporary fix to the bug in which we miss wake events when in deep
sleep with the LFIOSC (32kHz) clock and the EC is cold. This fix
involves simply using a faster clock, 250kHz, when in low speed
deep sleep. This fix consumes more power but solves the bug.
Renamed EC console command dsleepmask to dsleep.
BRANCH=none
BUG=chrome-os-partner:23678
TEST=Go in to low speed deep sleep by going into either S3 or G3
and letting the EC console timeout. Then freeze-spray the EC chip.
Wake up the EC via the console and make sure that the idlestats
show that we have not missed a deadline.
Change-Id: I4f9844f1937bc8c95cf1540502f7d8fb4cbc097e
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175614
Reviewed-by: Randall Spangler <rspangler@chromium.org>
That way all the users of jump tags don't need to know about the
padding requirements.
BUG=chrome-os-partner:23851
BRANCH=none
TEST=enable CONFIG_CMD_JUMPTAGS, then 'jumptags'. Output should be
something like this:
20007fbc: 0x5550 UP.1 2
20007fc4: 0x4b42 KB.2 3
20007fcc: 0x4c50 LP.1 12
20007fdc: 0x4d54 MT.1 8
All the addresses in the first column should be word-aligned. The
sizes in the last column don't need to be a multiple of 4.
Change-Id: I91f9c29701a007ef8a56b5b7e0ea09930dfbea31
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175591
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Add bug references. Remove one assert that can no longer be triggered.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards; pass unit tests
Change-Id: I3f4d2e4f2f3343a8d0531cb0715d151eaa4d0b50
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175293
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
No code changes, just comment fixes. Added config #ifdefs for the
debug commands as requested; they're enabled for Spring, so
functionality is unchanged.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build spring; see that ilim and batdebug commands still exist
Change-Id: I7c9f12281afa7ec68aa7e62dcfcd51682d88a16a
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175216
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Rather than compile it by default for host-based tests, only compile
it for the few tests that actually use it. Since those (and all
boards) now only use if if they also have a keyscan task, we can get
rid of the #ifdefs in keyboard_mkbp.c as well.
And remove a TODO we'll never do...
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards; pass unit tests. These pass:
util/make_all.sh
make BOARD=pit tests
Change-Id: I44d1806cfb375027a7ed0b33a5e9bdbbed8ccddc
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/174513
There is a logical difference between PWM controls for things like
backlights and fan controls for actual fans. This change separates them into
two different data structures, for better abstraction.
BUG=chrome-os-partner:23530
BRANCH=none
TEST=manual
make runtests, make all boards, test on Link and Falco.
Change-Id: Ib63f2d1518fcc2ee367f81bf5d803360c1aa5c76
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175151
Instead of just configuring fan support as yes/no, we'll use it to specify
the number of fans on the board. Undefined (not zero!) means no fan support
at all.
Syntax change only. No new functionality.
BUG=chrome-os-partner:23530
BRANCH=none
TEST=manual
make runtests, build all platforms, build and test on Link.
Change-Id: Iff65efa69e05f3e1a54fdc2a8da9001b4e8487ca
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175150
This looks like a lot, but it's really just moving the non-board-specific
stuff from chip/lm4/fan.c into common/fan.c, updating the appropriate
headers, and renaming functions to better match the new location.
This is entirely code refactoring and renaming. No new functionality.
BUG=chrome-os-partner:23530
BRANCH=none
TEST=manual
make runtests, build all platforms, build and test on Link.
Change-Id: I7dc03d6732bad83cf838a86600b42a7cff5aa7aa
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175012
This is to add nyan board support:
- new files in board/nyan folder, including battery.c
- new common/chipset_tegra.c, which is mostly based on
chipset_gaia.c
- new include/tegra_power.h
- modified build.mk and flash_ec for nyan
BUG=none
BRANCH=nyan
TEST=tested on Venice 2 board
Change-Id: I36895f34f2f4d144a9440aff358c8274797ebbd6
Signed-off-by: Yen Lin <yelin@nvidia.com>
Reviewed-on: https://chromium-review.googlesource.com/168078
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Add some missing descriptions in config.h and rename a few defines to
be more consistent.
No functional changes, just comments and symbol renaming.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms; pass unit tests
Change-Id: I05a9a2ed6fd7bc8b14a18a0dc57d7d22430de21a
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/173111
Reviewed-by: Vic Yang <victoryang@chromium.org>
First implementation of a low power idle task for the LM4 chip. The
low power mode is selected by defining CONFIG_LOW_POWER_IDLE in a
board.h file. This commit turns it on for Peppy, Slippy, and Falco
only because those are the only boards tested.
When using the low power idle task, the chip goes in to deep sleep
when it can. Deep sleep disables clocks to most peripherals and puts
the onboard flash and RAM into a low power mode. The chip is woken
out of deep sleep using the RTC in the hibernate module. Increased
the idle task stack size to handle more involved idle task.
In board.c, the array of GPIO info can be used to select which GPIO
points can wake up the EC from deep sleep. Currenlty selected are
the power button, lid open, AC present, PCH_SLP_S3, and PCH_SLP_S5.
Additionally the port with the KB scan row GPIO point is also
enabled to wake up the EC from deep sleep.
Signed-off-by: Alec Berg <alecaberg@chromium.org>
BUG=None
BRANCH=none
TEST=Passes all unit tests. Runs on slippy, peppy, and falco with no
noticeable side affects. Verified that the power consumed by the EC
is lower when in S3, S5 and G3 by scoping the sense resistor
powering the chip.
Change-Id: I83fa9a159a4b79201b99f2c32678dc4fc8921726
Reviewed-on: https://chromium-review.googlesource.com/172183
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Alec Berg <alecaberg@chromium.org>
Tested-by: Alec Berg <alecaberg@chromium.org>
When the EC CPU is running at a decreased clock frequency, frequent
keyboard scans can starve other EC tasks of CPU and lead to dropped
data or watchdog timeouts.
Enforce a minimum number of EC clocks between keyboard scans to
prevent this from happening. The default chosen (16000 clocks) is
equal to the shortest post-scan delay (1 ms) of any current board when
the AP is in S0, so this should have no effect when the AP is in S0.
When the AP is in S3 or S5, we don't need to scan the keyboard as
frequently anyway. This can be overridden on a per-board basis for
future boards if needed.
BUG=chrome-os-partner:23247
BRANCH=pit
TEST=apshutdown, then hold down a key for 10 seconds. Should not see a
watchdog reset.
Change-Id: I228f53a32ad4769f6a137a9ab06903111bea115d
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/172895
Reviewed-by: Vic Yang <victoryang@chromium.org>
This is an initial version of power sequencing for the rambi rev.1
boards. It has a workaround for a rev.1 board problem; this requires
turning on PP5000 early.
BUG=chrome-os-partner:22895
BRANCH=none
TEST=AP should power on to S0 (PLTRST# deasserts) automatically when EC boots
Then 'apshutdown' should drag it back to G3.
Then 'powerbtn' should take it back to S0.
Change-Id: Id9bc6fe9b55fce3eb46ce1265891724ec7a4ae20
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/172675
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Silego chip used on Rambi inverts column 2. So the EC should pull the signal low when NOT scanning column 2, and release it at all other times.
BUG=chrome-os-partner:23198
BRANCH=none
TEST=not yet; need to probe on scope
Change-Id: If6a784493533f11ae54d18f27591697e69aa2282
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/172674
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Created a new function to enable or disable clocks to various
peripherals. This new function makes it easy to specify if you
want the clock enabled in run mode, sleep mode, and/or deep
sleep mode.
Added infrastructure to specify which GPIOs should interrupt the
EC from deep sleep.
BUG=none
BRANCH=none
TEST=Passes all unit tests. Ran on a peppy and verified that
the clock gate control registers in run mode (LM4_RCGC regs)
were the same before and after this change.
Change-Id: Ia5009ac8c837f61dca52fe86ebdeede2e1a7fe4d
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/172454
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The LED state machine ends up being very board-specific, as does the
specific configuration of LEDs and whether they're PWM'd or just
GPIOs. dparker has some clever ideas for how to move more of the
functionality to common/led_common.c (used at present only by peppy);
that will be done as a follow-on to this CL.
There's a unit test for the spring LED implementation. To keep that
compiling, just use a symlink to the spring-specific implementation.
No code changes; just moving around files.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards; pass unit tests
Change-Id: I5973e701a29a72575db9a161dc146855ab21cca6
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/171771
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
include/config.h should have the canonical list of all CONFIG_* macros used
everywhere else. This fixes some that weren't included, and some that had
been changed in one place but not in others.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=manual
Build everything. It should still work.
cd src/plaform/ec
make runtests
for i in bds bolt daisy discovery falco kirby link mccroskey peppy pit puppy rambi samus slippy snow spring; do make BOARD=$i || touch died.$i; done
There shouldn't be any died.* files.
Change-Id: I0a1ec2d57668509c514dc5a521e547836a3e9894
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/171690
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This was previously done in a board-specific function across 4 boards.
Except that the board-specific function was identical in all cases
(that is, not really board-specific). Put it back in the common
implementation to get rid of duplicated code, and use
CONFIG_TEMP_SENSOR_POWER_GPIO to indicate which GPIO rail controls the
sensor power.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards; pass unit tests
Change-Id: I29de40001d5d4dc873e5ba8f3abb328c6271f235
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/171140
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
The old backlight_x86 code did
(backlight enable) = (lid is open) && (GPIO request from AP)
Newer systems will AND those signals in hardware. Support those
systems by separating CONFIG_BACKLIGHT_LID and
CONFIG_BACKLIGHT_REQ_GPIO, and add tests for the case where the enable
signal is dependent only on the lid position.
BUG=chrome-os-partner:22960
BRANCH=none
TEST=pass unit tests
Change-Id: I1909426e49f00a8acd5047fd88c801cba1dacd76
Reviewed-on: https://chromium-review.googlesource.com/170925
Tested-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Commit-Queue: Randall Spangler <rspangler@chromium.org>
With the PWM interface refactoring, only the CPU fan uses the fan.h
interface. All other PWM channels (keyboard backlight, etc.) use the
pwm.h interface. Remove the unused constants, and rename FAN_CH_CPU
to CONFIG_FAN_CH_CPU so it fits with the other fan config options.
No functional changes; just renaming things.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all targets; pass unit tests
Change-Id: I391fbeaf54afcc29a11c2799a4520b7ad8784796
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170534
Reviewed-by: Vic Yang <victoryang@chromium.org>
switch.c currently assumes that all boards have GPIO_RECOVERY_L. This
is not true for Rambi, and also isn't true for ARM boards (which
should also eventually use the common switch implementation).
Add a new CONFIG_SWITCH_DEDICATED_RECOVERY option to control whether
to compile this support.
BUG=chrome-os-partner:22893
BRANCH=none
TEST=compile all boards; pass unit tests
Change-Id: If6f34d1afd580c9d79a8edcdda18833068e70f66
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170489
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
The battery files contain board-specific constants and a few small
methods like battery-detect and battery-cut. Most of these aren't
reused across platforms. The battery files have also been cleaned up
so those board-specific constants basically all that's left in them.
Where a file is used by a single board only, move it to
board/(boardname)/battery.c. Batteries used by more than one board
(e.g. battery_link.c used by both link and bolt) are still in
common/battery_*.c, since that's cleaner than duplicating the file in
each board's directory.
No code changes, just moving files.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all boards and pass unit tests
Change-Id: I946c8eb874672c77f9b77105e5b900f98fa48d0f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169893
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
STM32 has a single-byte mailbox for UART I/O. When the core clock
runs at 16Mhz we can service interrupts fast enough to handle 115200
baud input, but when we drop to 1MHz we drop characters. Using DMA to
receive input solves this problem.
The STM32 DMA engine can only generate interrupts when the transfer is
half-done / all-done, so we need to poll the DMA receive-head-pointer
to see if individual characters have been received. Do this in the
tick task (every 250ms). When a character is received, poll more
quickly for a bit (5 times before the next tick) so the input console
is more responsive to typing.
BUG=chrome-os-partner:20485
BRANCH=none
TEST=Console is responsive to debug commands. For example, help -> prints help
apshutdown -> shuts down AP
arrow keys -> move cursor and scroll through command history
Ctrl+Q, help, wait a second, Ctrl+S -> help output printed after Ctrl+S
Then in chip/stm32/config_chip.h, comment out #define CONFIG_UART_RX_DMA
and rebuild/reflash the EC. When the AP is up, the console works normally
but after 'apshutdown', the EC drops to 1MHz core clock, and the arrow
keys don't work. (This step confirms that adding DMA support did not
change the behavior of systems where CONFIG_UART_RX_DMA is not defined.)
Change-Id: I199448354824bd747c7b290ea7fd5ccf354c11bb
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169406
Reviewed-by: Simon Glass <sjg@chromium.org>
If CONFIG_HOOK_DEBUG is defined, the maximum run time of each hook is
recorded. Also, record the delayed amount of time of HOOK_TICK and
HOOK_SECOND firing. The statistics are available through console command
'hookstats'.
Also fix a bug that CC_HOOK is used but not defined when
CONFIG_HOOK_DEBUG is defined.
BUG=chrome-os-partner:21801
TEST=Build with HOOK_DEBUG and check 'hookstats'
BRANCH=None
Change-Id: I3acba3abdd487cf20d9a532429f766cdddea2e93
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169274
This reduces the number of UART interrupts by a factor of 12, and
reduces the overall interrupt rate on STM32 by a factor of 2.
BUG=chrome-os-partner:20485
BRANCH=none (not required for pit branch)
TEST=Boot pit. Ctrl+Q pauses debug output; Ctrl+S resumes it.
'crash divzero' still prints a full crash dump.
And util/makeall.sh passes builds all platforms and passes tests.
Change-Id: I86993e14b436150298dcb2c6d29086cc3c9db418
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168814
Depending on the system, the AP can be throttled in at least two different
ways - politely, where it's just asked to slow down a bit, and forcefully
using a hardware signal (like PROCHOT). In addition, the request for
throttling can come from multiple tasks.
This CL provides a single interface, specifying both the type of throttling
desired and the source of the throttling request.
For each type, any source can can start throttling, but all sources must
agree before it stops. The changes are protected by a mutex, so that
requests from multiple tasks don't interfere with each other.
BUG=chrome-os-partner:20739,chromium:287985,chromium:287983
BRANCH=ToT
TEST=manual
Build-time test:
cd src/platform/ec
make BOARD=falco runtests
Run-time test: Lower the temp thresholds, turn the fan off, and watch the
throttling turn off and on as things heat up. For example, on the EC
console:
> temps
PECI : 339 K = 66 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
> thermalset 0 341 343
sensor warn high halt fan_off fan_max name
0 341 343 383 333 363 PECI
1 0 0 0 0 0 ECInternal
2 0 0 0 0 0 G781Internal
3 0 0 0 0 0 G781External
>
> temps
PECI : 339 K = 66 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
>
> fanduty 0
Setting fan duty cycle to 0%
>
> apthrottle
AP throttling type 0 is off (0x00000000)
AP throttling type 1 is off (0x00000000)
>
[430.152000 thermal WARN]
[430.152233 event set 0x00020000]
[430.152497 event clear 0x00020000]
[430.152714 ACPI query = 18]
[430.152444 sci 0x00020000]
[430.153051 set AP throttling type 0 to on (0x00000001)]
> gpioget CPU_PROCHOT
0 CPU_PROCHOT
>
[436.153742 thermal HIGH]
[436.153979 set AP throttling type 1 to on (0x00000001)]
> gpioget CPU_PROCHOT
1* CPU_PROCHOT
> [441.155319 thermal no longer high]
[441.155587 set AP throttling type 1 to off (0x00000000)]
[442.155604 thermal HIGH]
[442.155841 set AP throttling type 1 to on (0x00000001)]
[446.156623 thermal no longer high]
[446.156890 set AP throttling type 1 to off (0x00000000)]
temps
PECI : 343 K = 70 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
>
[447.156827 thermal HIGH]
[447.157064 set AP throttling type 1 to on (0x00000001)]
apthrottle
AP throttling type 0 is on (0x00000001)
AP throttling type 1 is on (0x00000001)
> gpioget CPU_PROCHOT
1 CPU_PROCHOT
>
Now turn the fan back on:
> fanauto
>
[456.159306 thermal no longer high]
[456.159574 set AP throttling type 1 to off (0x00000000)]
> apthrottle
AP throttling type 0 is on (0x00000001)
AP throttling type 1 is off (0x00000000)
> temps
PECI : 341 K = 68 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
>
[473.163905 thermal no longer warn]
[473.164168 event set 0x00040000]
[473.164453 event clear 0x00040000]
[473.164670 ACPI query = 19]
[473.164379 sci 0x00040000]
[473.164987 set AP throttling type 0 to off (0x00000000)]
temps
PECI : 340 K = 67 C
ECInternal : 324 K = 51 C
G781Internal : 328 K = 55 C
G781External : 327 K = 54 C
>
> apthrottle
AP throttling type 0 is off (0x00000000)
AP throttling type 1 is off (0x00000000)
>
Change-Id: I9ee1491a637d7766395c71e57483fbd9177ea554
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168802
This is in preparation for enabling DMA-based UART transfers, to
improve UART performance on STM32.
BUG=chrome-os-partner:20485
BRANCH=none
TEST=Boot pit. Host commands should still be received; this verifies DMA
is still operational.
Change-Id: Ibc3b2e2cd187547eb61b85e4a086704accd7f2fb
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168810
Currently only x86 platform uses charge_state.c, and it's been tailored
to fit smart battery and bq247xx charger family.
For Kirby, we have different types of battery and charger, and thus need
to make some change to accommodate them. This includes:
- Abstract out smart battery specific bit mask
- Implement missing functions required by GAIA chipset module
- Add config flags for charging-enabled GPIO pin
- Allow battery that doesn't report desired voltage and current
BUG=chrome-os-partner:22055
TEST=Build all boards
TEST=Boot Link and check it charges/discharges battery
TEST=Test charging/discharging on Kirby along with the next two CLs
BRANCH=None
Change-Id: I910c030a45b4f775afffec0127cdc31e89b9dd55
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168005
BQ27541 is not a smart battery IC, and thus we cannot use existing smart
battery driver. Let's add a driver that implements a smart-battery-like
interface.
The 'battery' console command is also moved to battery.c so that it can
be reused by different battery driver.
BUG=chrome-os-partner:22048
TEST=Type 'battery' and check the reported values are sane.
TEST=Check 'battery' command works fine on Spring.
BRANCH=None
Change-Id: I5d1eaeb3f801478f3b9473fd43c1f2a2eda75859
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/66340
This adds EC_CMD_GET_SET_VALUE to the list of host commands. We have a bunch
of single-value getter/setter commands, which is wasteful. This is a start
towards unifying them into a simpler command.
BUG=chromium:285358
BRANCH=ToT,falco
TEST=none
There's nothing to test just yet. This just adds the command and some basic
interfaces. A future commit will make use of it.
Change-Id: Iee986b9d273b422bb06f3a0c9b7af50617f03d7f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168083
Reviewed-by: Randall Spangler <rspangler@chromium.org>
ADC module on STM32L is clocked by HSI oscillator, and thus we need to
switch to HSI if using MSI. After the conversion, if the system is not
in S0, clock is switched back to MSI again.
There are several register bits that can only be written when ADC is
powered down. For now, let's just power down the ADC after each
conversion.
Currently ADC watchdog is not working and is disabled on STM32L.
BUG=chrome-os-partner:22242
TEST=Try multiple all-channel and single-channel reads in S0 and S5.
BRANCH=None
Change-Id: I769dda8a9c69ac9de1eb22d6d259034eef8c1ac4
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167454
Instead of checking for BOARD_<board> to determine whether the board has
control over a power rail or not, use config option for this. Boards
without control over some power rails can then undefine the option in
board.h.
BUG=chrome-os-partner:21964
TEST=Build all boards.
BRANCH=None
Change-Id: I7ee4ebdb3ea595e182845e40db165623ee271997
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167200
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The ID detection and charging circuits on Spring are very different from
that on Kirby. PWM current limit is no longer used. The ID detection
sequence is also different. Also, there is no boost circuit on Kirby.
Given those hardware issues that we had to work around on Spring, it's
unlikely that we will have another board that shares the same/similar
ID detection design with Spring. Let's rename extpower_usb to
extpower_spring to better reflect this.
BUG=None
TEST=Build and boot Spring.
BRANCH=None
Change-Id: I7c212a121eed55665593cb7e1b2b672891819940
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/67031
This unifies the PWM module interface for LM4 and STM32. Now PWM
channels are defined in board.h/board.c. Instead of calling functions
named pwm_set_fan_duty(x), one can now use pwm_set_duty(PWM_CH_FAN, x),
which prevents additional functions added when we have a new PWM
channel.
BUG=chrome-os-partner:18343
TEST=Limit input current on Spring.
TEST=Check power LED in S0/S3/S5 on Snow.
TEST=Check keyboard backlight functionality on Link.
TEST=Check fan speed control/detecting on Link.
BRANCH=None
Change-Id: Ibac4d79f72e65c94776d503558a7592f7db859dc
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/64450
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Problems with existing thermal control loop:
* Not multi-board friendly. thermal.c only supports Link and needs
refactoring. Temp thresholds and fan speeds are hard-coded.
* Only the PECI temp is used to determine the fan speed. Other temp sensors
are ignored.
* Has confusing data structures. Values in the CPU temp thresholds array mix
ACPI thresholds with fan step values.
With this change, the thermal task monitors all temp sensors in order to
perform two completely independent functions:
Function one: Determine if the host needs to be throttled by or informed of
any thermal events.
For thermal events, each temp sensor will have three threshold levels.
TEMP_HOST_WARN
* When any sensor goes above this level, host_throttle_cpu(1) will be called
to ask the CPU to slow itself down.
* When all sensors drop below this level, host_throttle_cpu(0) will be called.
* Exactly AT this level, nothing happens (this provides hysteresis).
TEMP_HOST_HIGH
* When any sensor goes above this level, chipset_throttle_cpu(1) will be
called to slow the CPU down whether it wants to or not.
* When all sensors drop below this level, chipset_throttle_cpu(0) will be
called.
* Exactly AT this level, nothing happens (this provides hysteresis).
TEMP_HOST_SHUTDOWN
* When any sensor is above this level, chipset_force_shutdown() will be
called to halt the CPU.
* Nothing turns the CPU back on again - the user just has to wait for things
to cool off. Pressing the power button too soon will just trigger shutdown
again as soon as the EC can read the host temp.
Function two: Determine the amount of fan cooling needed
For fan cooling, each temp sensor will have two levels.
TEMP_FAN_OFF
* At or below this temperature, no active cooling is needed.
TEMP_FAN_MAX
* At or above this temperature, active cooling should be running at maximum.
The highest level of all temp sensors will be used to request the amount of
active cooling needed. The function pwm_fan_percent_to_rpm() is invoked to
convert the amount of cooling to the target fan RPM.
The default pwm_fan_percent_to_rpm() function converts smoothly between the
configured CONFIG_PWM_FAN_RPM_MIN and CONFIG_PWM_FAN_RPM_MAX for percentages
between 1 and 100. 0% means "off".
The default function probably provide the smoothest and quietest behavior,
but individual boards can provide their own pwm_fan_percent_to_rpm() to
implement whatever curves, hysteresis, feedback, or other hackery they wish.
BUG=chrome-os-partner:20805
BRANCH=none
TEST=manual
Compile-time test with
make BOARD=falco runtests
On the EC console, the existing fan commands should work correctly:
faninfo - display the fan state
fanduty NUM - force the fan PWM to the specified percentage (0-100)
fanset RPM - force the fan to the specified RPM
fanset NUM% - force the fan to the specified percentage (0-100) between
its configured minimum and maximum speeds from board.h
(CONFIG_PWM_FAN_RPM_MIN and CONFIG_PWM_FAN_RPM_MAX)
fanauto - let the EC control the fan automatically
You can test the default pwm_fan_percent_to_rpm() with
fanset 1%
faninfo
The fan should be turning at CONFIG_PWM_FAN_RPM_MIN. Let the EC control it
automatically again with
fanauto
Also on the EC console, the thermal settings can be examined or changed:
> temps
PECI : 327 K = 54 C
ECInternal : 320 K = 47 C
G781Internal : 319 K = 46 C
G781External : 318 K = 45 C
>
> thermalget
sensor warn high shutdown fan_off fan_max name
0 373 387 383 333 363 PECI
1 0 0 0 0 0 ECInternal
2 0 0 0 0 0 G781Internal
3 0 0 0 0 0 G781External
>
> help thermalset
Usage: thermalset sensor warn [high [shutdown [fan_off [fan_max]]]]
set thermal parameters (-1 to skip)
>
> thermalset 2 -1 -1 999
sensor warn high shutdown fan_off fan_max name
0 373 387 383 333 363 PECI
1 0 0 0 0 0 ECInternal
2 0 0 999 0 0 G781Internal
3 0 0 0 0 0 G781External
>
From the host, ectool can be used to get and set these parameters with
nearly identical commands:
ectool thermalget
ectool thermalset 2 -1 -1 999
Change-Id: Idb27977278f766826045fb7d41929953ec6b1cca
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66688
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The BOOTCFG register configures a couple of important things: whether to
allow jumping into the builtin ROM bootloader at reset, and whether or not
to allow JTAG access for programing and debugging.
The default is "no" and "yes". But the BOOTCFG register can be locked so
that it can't be changed again, which means that if the wrong values are put
into it, the system is pretty much bricked.
On Link, we wrote a BOOTCFG value that allowed a GPIO to be used as a bypass
to optionally trigger the ROM bootloader, but on Slippy and its derivatives
that GPIO is not pulled up. If you program the Link values into BOOTCFG on a
Slippy, the system is stuck in the ROM bootloader more or less forever.
This change disables that GPIO, keeps JTAG enabled, and locks those settings
for all LM4 chips (it's a chip config now, not a board config). We've never
actually used the GPIO to invoke the ROM bootloader, but we have managed to
brick a number of systems just by having it enabled, so we're going to lock
it into a safe configuration now.
BUG=chrome-os-partner:19247
BRANCH=falco,peppy
TEST=manual
Reflash, boot, power cycle (actually unplug the EC from AC and battery) a
few times. It should continue to work.
Change-Id: Iaf1a81d6814104421a56425490e3d5164ea9b617
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66538
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
BUG=chrome-os-partner:21847
BRANCH=peppy
TEST=Manual. Check state of GPIO_P5000_FAN_EN with lid open
and lid closed. Can also check with meter via TP109.
Change-Id: I8a64c14d53dd84a5d586c0abb04ccb71de0e78b3
Signed-off-by: Dave Parker <dparker@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65674
Only link actually used this function, but all batteries were required
to provide an (empty) implementation. Use
CONFIG_BATTERY_VENDOR_PARAMS to gate this functionality, so non-link
battery code can be simpler.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms and pass unit tests
Change-Id: Ic2c6dd1163a981e48873d798f77891cc7de1f8cf
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65257
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Rong Chang <rongchang@chromium.org>
