STM32 seems to actually measure the rising and falling time of the I2C clock, so
if one uses a really small resistor the timing will go faster than with a bigger
resistor.
This commit makes it so the I2C frequency is limited to max 100kHz (respecting
the spec) no matter what size resistor (essentially we assume 0 rise and fall
times). While this will make stuff slower on boards with big resistors (where
they might have been under 100kHz anyway) this is the best compromise (since the
spec does not specify min frequency) without getting config defines for the
fall/rise times.
The TSCLH of some boards would be too short with the recommended timing
settings from spec, so increases the TSCLH would be better for everyone.
This patch does not touch the higher frequencies since the rise and fall times
do contribute a lot more to clocks, if the same method was used for those
frequencies, the speeds would have to be a lot slower.
BUG=chrome-os-partner:34375
BRANCH=None
TEST=on any EC, note how frequency does not go above 100kHz
TEST=As per tSCL = tSYNC1 + tSYNC2 + { [(SCLH+1) + (SCLL+1)] x
(PRESC+1) x tI2CCLK } from datasheet
Change-Id: Ibbeecac7f3da1b22d2ba3bca29ee3c17bfe997f5
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/234077
Reviewed-by: Randall Spangler <rspangler@chromium.org>
When the EC is busy enough to start missing RX characters an ORECF might come
(Overrun error), we never check for this bit, so that means the interrupt
handler will be called in a loop because it never clears that bit.
This disables the overrun detection feature.
BUG=chrome-os-partner:33451
TEST=get firmware to poll the EC for keyboard presses, type really fast on the
keyboard, note how system does not watchdog reset anymore but loses the
occasional character instead.
BRANCH=None
Change-Id: I711483768e4ba80aaeb4a324c7dee790b3a23682
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/236088
Reviewed-by: Randall Spangler <rspangler@chromium.org>
According the STM32L RM, when writing to RCC_CFGR to change HSI or MSI
clock source, SWS bits of RCC_CFGR register have to be checked if the
new clock source is taken into account. Also, when writing ACC64 bit and
LATENCY bit to FLASH_ACR register, those bits have to be checked too.
Also changed in this CL is to disable MSI if HSI is enabled, and disable
HSI if MSI is enabled.
BUG=chrome-os-partner:32936
BRANCH=none
TEST=passed suspend_stress_test on big, blaze and nyan
Change-Id: I3ec660d149ecdec3ca3097239612bf2c542d0548
Signed-off-by: Yen Lin <yelin@nvidia.com>
Reviewed-on: https://chromium-review.googlesource.com/234490
Reviewed-by: Kary Jin <karyj@nvidia.com>
Tested-by: Kary Jin <karyj@nvidia.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
(cherry picked from commit 400d9dca8c41f74cf0c2587e881707b80bb17d3d)
Reviewed-on: https://chromium-review.googlesource.com/236050
Added check for collision just before transmitting on CC line.
To check for collision, RX monitoring is left on all the time
(except when in the act of receiving or transmitting, or in
between receiving and sending a goodCRC), and a
simple check for RX transmission started is used to see if the
CC line is idle or not.
RX monitoring is also changed to only trigger on 3 edges within
20us, as per the PD spec.
When a collision is detected by seeing that CC is not idle, the
transmitting packet is dropped.
BUG=chrome-os-partner:30135
BRANCH=samus
TEST=load onto samus and zinger. make sure we negotiate and make
sure custom VDMs succeed. enabled pings and made sure we stay
alive with pings for a few min.
Also added code to pd_rx_handler to toggle a test point on EVT
board to verify the timing of when we get RX interrupts:
Change-Id: I22d172163319437d3d901e019eda79d4d592f6b8
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/226118
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Ryu sensor hub has asymectric RO/RW images. The first one is very limited
(not i2c master, no sensor drivers, gesture recognition).
Image size is alter to offer more space for the RW firmware image,
compiled with ryu_sh board.
To write RO image and basic RW image:
flashrom -V -p ec:type=sh,block=0x800 --fast-verify -w /tmp/ryu_sh_loader/ec.bin
To write the expected RW image:
flashrom -V -p ec:type=sh,block=0x800 --fast-verify -w -i EC_RW:/tmp/ryu_sh/ec.bin
BRANCH=ToT
BUG=chrome-os-partner:33908
CQ-DEPEND=CL:231970,CL:233233
TEST=load on Ryu, confirmed limited operation.
Change-Id: Ib976e2b048935adfb9b2b072c071db5be2bc1c09
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/231984
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The task based approach made sense when it looked like
there would be a case closed debugging task to handle
multiple bridges (SPI/I2C/USART...). I'm not convinced
anymore that that task will be needed, so this
simplification seems good.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Change-Id: Ic431c287c28d10252246fe9f507d9c5fcc64a077
Reviewed-on: https://chromium-review.googlesource.com/232733
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
This allows the USB SPI bridge to be controlled from the
host at a larger timescale than a single SPI transaction.
This allows the host to signal that many transactions
will take place and that the device should keep the SPI
bridge enabled across them. This allows the device to
hold the AP or other possible user of the SPI bus in
reset while the bridge is enabled.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Change-Id: Ifd6f96b0ff47f35d853735d44e255a205b0e677a
Reviewed-on: https://chromium-review.googlesource.com/232732
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Build the hardware version string from the register definitions,
so I no longer forget to update it.
Check it at runtime against the build version registers.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=On the console command line,
type "version" and see the following string:
"Chip: g cr50 A1 20141203_224409"
Change-Id: I6d902780d42f2dd18a57ccc08fd4ba4fee5ebc7c
Reviewed-on: https://chromium-review.googlesource.com/233582
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
- record and display reset cause
- add the hard reset option
- add the scratchpad to store values across reboots.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:33818
TEST=On the console command line, chech the "[Reset cause: xxx]" string
- for the initial reset cause
- use "waitms 4000" to trigger a watchdog reset
- use "reboot soft"
- use "reboot hard"
The "utils" test is now building and passing.
Change-Id: I68c7096e5b7bfd102be89fd8eef6fe20da37a6f8
Reviewed-on: https://chromium-review.googlesource.com/233581
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Implement a driver to trigger a watchdog reboot if we are stuck
somewhere. Also display a nice warning when we reach half of the
watchdog period.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=On the console, type "waitms 500" and see nothing,
type "waitms 2000" and see the watchdog warning.
Type "waitms 4000" and see the warning, the platform rebooting.
Change-Id: Iac5d0100febd5eab1ae6cfac5a47ff728ebda3a6
Reviewed-on: https://chromium-review.googlesource.com/233430
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
We were losing timer events because usecs_to_ticks(deadline) was
clipping the value when deadline was larger than 0x08888888 (deadline is
a timestamp rather than a delay).
The computation of the timer deadline has been modified to avoid the
clipping issue.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:34347
TEST=run on Cr50 with the watchdog activated and no longer see watchdog
warnings.
Run the "timer_calib" test and see that the 1s sleep is 1000038 us :
make BOARD=cr50 tests
fhl ../build/cr50/timer_calib/timer_calib.RO.hex
Change-Id: Id2200a89eb1b72099e536291af321609b24b4777
Reviewed-on: https://chromium-review.googlesource.com/233531
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Trybot-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
CL to migrate the flashing VDMs from zinger's custom vdm to
common/usb_pd_flash.c such that other updateable type-C devices can
share.
Additionally adds gaskets to call standard runtime flashing facilities
for USB-PD devices using it.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BRANCH=samus
BUG=chrome-os-partner:31192,chrome-os-partner:31193
TEST=manual,
Try following:
1. From samus_pd console w/ zinger in port 1
pd 1 flash version
pd 1 flash reboot
pd 1 flash info
2. From samus linux prompt w/ zinger in port 1
ectool --name cros_pd flashpd 1 1 <zinger RW payload>
Reading 16384 bytes from
/usr/local/zinger_v1.1.2528-d809e42.ec.RW.bin...
Erasing expected RW hash
Rebooting
Erasing RW flash
Writing RW flash
Rebooting PD into new RW
Complete
3. Repeat 1&2 above on hoho & dingdong.
Change-Id: I018055fa9de128f937c57debdc21dea026137bcf
Reviewed-on: https://chromium-review.googlesource.com/231835
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
Commit-Queue: Todd Broch <tbroch@chromium.org>
Until we implement a proper reset of the microcontroller,
add a reset of the Cortex-M3 CPU core in system_reset() in order to
avoid getting stuck in a weird loop if we get a panic.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=trigger a data abort and verify we are not going into a panic loop.
Change-Id: Ie046379e6a9469bd683fa774cdc9abb10a14e8f1
Reviewed-on: https://chromium-review.googlesource.com/233109
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
A non-zero error code returned by the callback causes EP0 to STALL.
This is the common mechanism used in USB to indicate an error while
processing a control request. This simplifies the implementation
of interface callbacks.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Change-Id: I89ceb4892f9f810fcaf6e975e6982fc5b2ae447b
Reviewed-on: https://chromium-review.googlesource.com/232368
Reviewed-by: Anton Staaf <robotboy@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
When using gpio_set_flags_by_mask() to modify a GPIO pin setting, the
former code was not able to revert an open-drain GPIO into push-pull
mode (the other way round was working). Fix it to be able to transition
in each direction.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=all
BUG=none
TEST=on Twinkie, run "tw res none RP3A0" then "adc" and see the RP3A0
GPIO set to 1 and pulling the CC to 3.3V.
Change-Id: Ic2d8ed95ea21b21d261a12ba298931d8bd5e6919
Reviewed-on: https://chromium-review.googlesource.com/231150
Reviewed-by: Vic Yang <victoryang@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The latest gcc picked up a couple out-of-bounds issues, so
"make buildall" was failing. This fixes them.
BUG=none
BRANCH=ToT
TEST=make buildall -j
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Change-Id: Idcd6a3358ecbb0e0d2a610e1cd28c2f138ce520b
Reviewed-on: https://chromium-review.googlesource.com/231156
Reviewed-by: Randall Spangler <rspangler@chromium.org>
For USB console, we wait for USB host to grab the data before writing
the next chunk of characters. However, if the USB peripheral is
disabled, the current implementation is confused as to whether the host
has grabbed the previous chunk of data.
Fix this by explicitly checking for USB peripheral enabled.
BRANCH=ryu
BUG=None
TEST=Boot on Ryu and check console isn't slow.
Signed-off-by: Vic Yang <victoryang@chromium.org>
Change-Id: I438c95835e56707b7ca1796734f2e47062799f44
Reviewed-on: https://chromium-review.googlesource.com/231115
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This is fairly large change set to accomodate a new hardware
release. There are enough differences to require refactoring the
registers.h file. Autogenerated constants are now in gc_regdefs.h
and all constant names begin with GC_, while register names are
defined in registers.h and begin with GR_.
Yes, I know the new header files are wider than 80 chars, but we
agreed that was okay in some cases if it makes them more readable
(see commit 3500c28).
BUG=chrome-os-partner:33423
BRANCH=none
TEST=make buildall -j
Build and run on the development board.
Change-Id: I21bd88c490f4f359ad17b5af9d17d8caca8dc9e4
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/230513
Reviewed-by: Sheng-liang Song <ssl@chromium.org>
Add commands to send PD packets and to tweak individual parameters (TX
clock frequency, RX detection threshold, resistors on CCx).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:28337
TEST=verify that the PD sniffing is still working by dumping traffic
between Zinger and Samus.
Connect Twinkie to Zinger, set Rd by using "tw res NONE RD" and see VBUS
going to 5V (reading it using "ina 0").
Send a BIST mode 2 request using the following command :
tw send 2 0x1043 50000000
and see the other end starting sending BIST.
Change-Id: I3c8ddf858435ac1c17a43f59351bbaa69603a209
Reviewed-on: https://chromium-review.googlesource.com/227778
Reviewed-by: Todd Broch <tbroch@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Extend the Zinger runtime to take into account the disable_sleep()
issued by the USB protocol stack and avoid going into deep-sleep while
connected.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=none
TEST=connect Zinger to a PD power sink (Twinkie) and monitor the stop
mode entry/exit on a GPIO.
Change-Id: I04e35fdd65f3be3da7a4304dc1a92e6268930888
Reviewed-on: https://chromium-review.googlesource.com/230340
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Allow to use larger RSA keys by setting CONFIG_RSA_KEY_SIZE to 4096 or
8192 rather than using the default 2048-bit size.
It's mainly for benchmarking purpose right now as we don't have the RAM
to store the 3x key size buffer and the flash space for the public key
structure.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=samus
BUG=none
TEST=build Zinger with CONFIG_RSA_KEY_SIZE equals to 4096 and run it.
Change-Id: I9839121bf158d0a30dde1e48d875f345191bfec2
Reviewed-on: https://chromium-review.googlesource.com/228925
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
It's really annoying to have to type two different commands. If I
want to read a location and then write it and then read it back
(which often happens when poking at hardware), then this:
rw 0x40570008
rw 0x40570008 14
rw 0x40570008
is much easier to enter than this:
rw 0x40570008
ww 0x40570008 14
rw 0x40570008
The "ww" command is still there, if you're really attached to it.
BUG=none
BRANCH=none
TEST=manual
Tried the example above. It worked.
Change-Id: I2302ed60df3dd3ec2224afa7c32d997bd2468ec1
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/229660
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Implement the API expected by common/timer.c
BUG=chrome-os-partner:33699
BRANCH=none
TEST=manual
Run the "gettime" and "timerinfo" and "taskinfo" and "waitms"
commands. Compare the elapsed time with the real world. They seem
to match.
Change-Id: Ie5acae76780ee09e7dfb6cc0282de25f8063e96f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/229642
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This enables forwarding of the local PD/EC console
over debug USB. It gates the console functionality
based on the CCD mode that is set.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Enable partial CCD mode on ryu and verify that it is
enumerated by the host correctly, but doesn't respond
to console input, and doesn't generate output.
Enable full CCD mode on ryu and verify that it is
enumerated and that the console works as expected.
Verify that the console still works by default on the
discovery-stm32f072 board.
Change-Id: I0325ce9689486c41387d6075330be1d7d42f1d42
Reviewed-on: https://chromium-review.googlesource.com/229342
Reviewed-by: Anton Staaf <robotboy@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Previously enabling USB would automatically (using an
init hook) initialize the USB peripheral. This would
take over the GPIO lines assigned to the USB module.
This is not OK on Ryu for Case Closed Debug because it
interferes with the AP's access to the USB 2.0 lines
even when not in Case Close Debug mode.
This change adds a configuration option to inhibit this
default initialization of the USB peripheral. It also
renames the existing CONFIG_USB_INHIBIT to
CONFIG_USB_INHIBIT_CONNECT now that there are two
possible inhibitions.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Enable console on ryu_p2 and discovery-stm32f072 board
Verify that it works on both
Change-Id: I6734357131b4356e3d4164349d6c74deac196ce5
Reviewed-on: https://chromium-review.googlesource.com/229138
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Previously the usb driver used #ifs to select a mechanism to
enable and disable the DP pullup. This doesn't scale well,
especially when the knowledge of how to do this is not known
to the chip specific code, but instead is board specific (as
it is with the STM32F373).
This change uses the build systems ability to build chip family
specific files per build to select the appropriate behavior.
And on the STM32F3 family of parts it just calls out to a board
specific pair of connect/disconnect functions.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Enable console on ryu_p2 and discovery-stm32f072 board
Verify that it works on both
Change-Id: I976e02fbc7acbb0f85817d7295b26ee9ecab0711
Reviewed-on: https://chromium-review.googlesource.com/229040
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Previously the USB RAM size was off by a factor of two
for chips that required 32-bit alignment of accesses,
even though the underlying memory was 16-bits in size.
This change adds an additional configuration for the
access size (it still assumes that the underlying memory
is 16-bits in size) and uses that to adjust the USB_RAM
memory section in the linker scripts.
This change also removes the default values for the USB
RAM from stm32/config_chip.h because they mask issues
when new chips are added. It is better for a new chip
to fail to compile until these values are provided.
Finally, this change introduces a common USB API header
so that common code doesn't need to include the STM32
specific header.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Enable console on ryu_p2 and discovery-stm32f072 board
Verify that it works on both
Change-Id: Id118627f53e9e8ff1bd09fb51f1f9634ff495d19
Reviewed-on: https://chromium-review.googlesource.com/228833
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
The console code never worked with the old style STM32 USB
peripherals because no chips with that version of the peripheral
were being used. The STM32F373 uses the older USB peripheral.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Enable console on ryu_p2 and discovery-stm32f072 board
Verify that it works on both
Change-Id: I77d36c33712521d7840b4e3ca02ebbea5de3d5df
Reviewed-on: https://chromium-review.googlesource.com/227741
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
Modules that are enabled are listed below:
- Power Sequencing
- Keyboard Scan and Protocol
- LPC to support Keyboard
- Power Button Task
ec.spi.bin has to be generated manualy using
pack_ec.py
BUG=None
BRANCH=None
TEST=Tested on Stargo-Proto board
Change-Id: Ic5d504c3d6e9c7c5f3482fb7e9e37800b6274824
Signed-off-by: Divya Jyothi <divya.jyothi@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/226303
Reviewed-by: Vic Yang <victoryang@chromium.org>
The fans on samus have a recommended minimum duty cycle of 20%
while running, but 30% in order to start. We've been using the
EC's built-in fan controller for the start requirement, but it
has a minimum fast-start duty cycle of 50%. It turns out that
that speed is noticeably noisy.
This change handles the startup with logic in the EC instead, so
that the fan only tries to spin at 30% initially (or if it drops
too much below the minimum turning speed).
BUG=chrome-os-partner:33429
BRANCH=ToT,samus
TEST=make buildall -j
Boot the system, let it idle with the browser windows closed, the
browse a bit, then idle. Listen for changes to the fans.
Before, I could hear the fans kick in and out as the AP load
changed. Now it's much quieter.
Change-Id: Id35215520c064eb6843686ec8bb5f3618dac6cf6
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/227658
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Previously the version string was special cased in the USB stack
because the build system prevented the inclusion of ec_version.h in
any file other than common/version.c. This lead to common/version.c
being the only place that the USB version string could be computed
and thus the special case of filling in the version string descriptor
at run time. This made the USB stack more complex, and lead to the
common/version.c file including usb.h, which is actually STM32
specific.
Now, the portion of ec_version.h that is deterministic is only
updated when something in the tree actually changes (by way of a
conditional in the makefile), and ec_version.h no longer has to
depend on all object files (other than the special version.o).
This allows anyone to include ec_version.h as needed. In particular,
each board that wants to define a USB version string can directly
include ec_version.h and do so.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
touch files and verify rebuilds happen correctly
Change-Id: Ic84d0b9da90f82ebb4630fb550ec841071e25a49
Reviewed-on: https://chromium-review.googlesource.com/227211
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Anton Staaf <robotboy@chromium.org>
The serial console works. Nothing else is implemented yet.
BUG=none
BRANCH=ToT
TEST=make buildall -j
To build,
make BOARD=cr50 hex
Testing the result requires a development board. I have one. It
works with HW revision m3.dist_20140918_094011
Change-Id: I718d93572d315d13e96ef6f296c3c2796e928e66
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/226268
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Per table 6-24 of USB PD spec an alternate mode adapter (AMA) should
include both product & AMA VDOs.
BRANCH=samus
BUG=chrome-os-partner:31192,chrome-os-partner:31193
TEST=manual,
Connect hoho/dingdong to fpie/samus and see product VDO proceed the
AMA VDO in DFP_U console output:
Product VDO -----------------------------v
|------|
SVDM/5 [1] ff008041 340018d1 00000000 50100001 1100000b
Note, hoho's PID == 0x5010
And dingdong (0x5011)
SVDM/5 [1] ff008041 340018d1 00000000 50110001 1100000b
Also see bcdDevice field in descriptor match above data.
$ lsusb -v -d 18d1: | egrep -i "idproduct|bcddev"
idProduct 0x5011
bcdDevice 0.01
Change-Id: I4d898816a45c68c7ff75a54fd348fc11be408ae0
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/226125
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
USB Billboard class can be used to advertise an alternate mode capable
device that hasn't entered a mode. Additionally it can remain after
mode entry providing its Billboard capabilities descriptor is
updated.
This CL postpones enumeration which previously occurred after boot
until tAMETimeout has passed and alternate mode has NOT been entered.
Future CL could choose to also (re)enumerate with mode capabilities
although this is not required by the USB PD specification.
BRANCH=none
BUG=chrome-os-partner:31192,chrome-os-partner:31193
TEST=manual,
With DFP_U which does not enter mode see Billboard class enumerate
else it does not.
Change-Id: I59a0815cd0ea551ba9a878907c0184df4ba9480c
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/224663
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Now that the problem with UART in STOP mode is fixed, let's enable low
power idle for Ryu P2 boards.
BRANCH=None
BUG=chrome-os-partner:33219
TEST=Shut down the AP and unplug AC power. Check the EC goes into
deep-sleep by 'idlestat'.
TEST=Power up the AP and check the EC stays awake.
Change-Id: Ib8ad3763407315ec0f95551fa0fdd258a060e113
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/226312
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
