This commit includes changes required for
supporting a hardware based montgomery
modexp (r = a ^ e mod N).
The function bn_is_bit_set() was previously
static, and now added to internal.h, as this
function is used by the hardware implementation.
Add function declarations for new functions
related to the hardware implementation to
chip/g/dcrypto/internal.h
BRANCH=none
CQ-DEPEND=CL:*260618,CL:*260895
BUG=chrome-os-partner:43025,chrome-os-partner:47524
TEST=all tests in test/tpm_test/tpmtest.py pass
Change-Id: I5fe4a6692678b64f27659f42a08d200b6fe6f0cc
Signed-off-by: nagendra modadugu <ngm@google.com>
Reviewed-on: https://chromium-review.googlesource.com/347462
Commit-Ready: Nagendra Modadugu <ngm@google.com>
Tested-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
This commands makes it possible to control the PD chip (or
the interaction between EC and PD), from the AP.
- PD_SUSPEND: Suspends the PD chip: EC needs to stop talking
to PD chip. Useful at beginning of PD FW update.
- PD_RESUME: Resumes the PD chip: EC can start talking to PD
chip again. Useful at end of PD FW update.
- PD_RESET: Resets the PD chip (called at the end of the update).
- PD_CONTROL_DISABLE: Prevents further calls to this command
(for security reason, we do not want the AP to be able to
call the other subcommands after the update has been performed).
BRANCH=none
BUG=chrome-os-partner:52433
TEST=ectool pdcontrol {suspend,resume,reset,disable}
Change-Id: I7a955dd27b65086c21d195a6504aa7392eb0406d
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/342584
Reviewed-by: Randall Spangler <rspangler@google.com>
add a new config flag to support active low power control signal
BUG=chrome-os-partner:53665
BRANCH=none
TEST=Use multimeter to check for voltage present on the WiFi slot.
Use gpioget to check GPIO state in S0 (on) and S5 (off).
Change-Id: Ibeca88d16f39eadd7f29589cd3cd15aeef0dd524
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/347085
Commit-Ready: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Kevin uses inverted polarity (low = enable 5V output), so add a new CONFIG
to support this.
BUG=chrome-os-partner:53777
BRANCH=None
TEST=Manual on Kevin. Enable USB charger tasks, verify that VBUS is
properly detected on no-battery case.
Change-Id: Ifb3e5fa9db1973d9826435712711f0cb0fd1d3a5
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/349260
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Previously CONFIG_USB_PD_TCPM_VBUS had two uses which were independent:
- When operating as a TCPC, it indicated that the VBUS level should be
tracked (through GPIO inputs) and sent to the external TCPM when
appropriate.
- When operating as a TCPM, it indicated that the VBUS level should be
obtained by querying the TCPC.
These two independent uses have been split into
CONFIG_USB_PD_TCPC_TRACK_VBUS and CONFIG_USB_PD_VBUS_DETECT_TCPC, which
sould be more clear.
In addition, CONFIG_USB_PD_VBUS_DETECT_* CONFIGs have been added for
other means of VBUS detection.
BUG=chromium:616580
BRANCH=None
TEST=Verify kevin continues to boot + charge.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I936821481d6577e17e3e9c61ff97c037574d6923
Reviewed-on: https://chromium-review.googlesource.com/348950
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
move PRECHARGE_TIMEOUT to config.h so that we can customize precharge time to
meet client's spec.
BUG=none
BRANCH=master
TEST=`make -j buildall`, precharge time is set to 300s in elm.
Change-Id: I5c3bf0d5c5240b9c087e6cdb7c6e97301efa9f84
Signed-off-by: Ryan Zhang <Ryan.Zhang@quantatw.com>
Reviewed-on: https://chromium-review.googlesource.com/348151
Reviewed-by: Shawn N <shawnn@chromium.org>
Port SHA and P256 code to depend on third_party/cryptoc.
Remove config options CONFIG_SHA1, and CONFIG_SHA256 as
these are provided by third_party/cryptoc.
Also remove unused config options CONFIG_SHA384, CONFIG_SHA512.
Crypto functions prefixed by dcrypto_ (declared in internal.h ),
DCRYPTO_ (declared in dcrypto.h) are implemented under
chip/g/dcrypto, and otherwise are implemented under third_party/cryptoc.
BRANCH=none
BUG=chrome-os-partner:43025,chrome-os-partner:47524,chrome-os-partner:53782
TEST=all tests in test/tpm_test/tpmtest.py pass
Change-Id: If7da02849aba9703573559370af5fae721d594fc
Signed-off-by: nagendra modadugu <ngm@google.com>
Reviewed-on: https://chromium-review.googlesource.com/340853
Commit-Ready: Nagendra Modadugu <ngm@google.com>
Tested-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
There are a couple of issues that cr50 has when it cannot know the state
of servo, the EC, and the AP. This change adds support so we can detect
when the AP or EC has been powered on and when servo has been connected.
It uses the UART RX signals to monitor the power state of the AP and EC.
The TX signals are used to monitor the state of servo.
BUG=chrome-os-partner:52056,chrome-os-partner:52322
BRANCH=none
TEST=verify device states are correct when the AP and EC are powered on
or off and when Servo is attached or detached
Change-Id: Id0a2281b65cb367ecc8d0ca2f9a576672318a5fb
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/344019
Full implementation of NvMem read, write, and commit functions.
Includes partition definitions, shared memory allocation, and
initialization function.
Includes a set of unit tests located in ec/test/nvmem.c which
verify functionality.
This module is required by Cr50, however this CL does not
include any Cr50 specific code.
BUG=chrome-os-partner:44745
BRANCH=none
TEST=manual
make runtests TEST_LIST_HOST=nvmem and verify that all tests pass
Change-Id: I515b094f2179dbcb75dd11ab5b14434caad37edd
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/345632
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This change provides a console command for setting,
and loading a usb serial number from flash. This
feature adds CONFIG_USB_SERIALNO, and currently only
has a useful implementation when PSTATE is present.
BUG=chromium:571477
TEST=serialno set abcdef; serialno load; reboot
BRANCH=none
Change-Id: I3b24cfa2d52d54118bc3fd54b276e3d95412d245
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/337359
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This allows the AP to protect a I2C passthru bus. A board-specific
function then defines what I2C commands are allowed, so that we
can white/black list some addresses (e.g. I2C address allowing
PD chip FW updating).
BRANCH=none
BUG=chrome-os-partner:52431
TEST=Book elm-rev1
Change-Id: Ib106924418b16388ea8ea53c7b6bda6ef92e1d09
Signed-off-by: Nicolas Boichat <drinkcat@google.com>
Reviewed-on: https://chromium-review.googlesource.com/345761
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@google.com>
LPC access interrupt only enabled when EC entering deep doze mode. This
will reduce interrupt of LPC access. Also, this interrupt is always
enabled for LPC platform to support "CONFIG_LOW_POWER_S0".
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=Tested ectool command 'version' x 10000.
Change-Id: I9053c4018b38a8a852c3c6254e1fcde625f3fa3a
Reviewed-on: https://chromium-review.googlesource.com/336112
Commit-Ready: Dino Li <dino0303@gmail.com>
Tested-by: Dino Li <dino0303@gmail.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Driver implements TCPC for ANX74xx chips. Enables Type C
port for USB and DP alt mode. Enable port role swap feature.
Driver implements TCPC for ANX74xx chips firmware version 1.0 and later.
Please update to ANX74xx firmware to V1.0 or later version to work.
Change list:
1, modify the position of define and struct declare
which response the comment for patch 22.
BUG=chrome-os-partner:49510
BRANCH=none
TEST=tested compiled binary for pdeval-stm32f072 board with this patch.
Power contract establishment, port role swap, DP alt mode works fine.
Change-Id: Iae6322510605a08d3bdd08446116ef5f9e4f7a7c
Signed-off-by: Aman Kumar <akumar@analogixsemi.com>
Signed-off-by: Junhua Xia <jxia@analogixsemi.com>
Reviewed-on: https://chromium-review.googlesource.com/322433
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Previously usb_charger.c supported only pi3usb9281, but now support for
additional parts is required. Move pericom-specific code (including the
usb_charger tasks that handles various quirks of that part) to the
pi3usb9281 usb_switch driver.
Going forward, usb_switch drivers must implement
usb_charger_set_switches() and must have some method (such as a task or
interrupt handler) to update charge_manager with information about
attached chargers.
BUG=chrome-os-partner:53363
BRANCH=None
TEST=`make buildall -j`
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I4df74e043d8cf2e532d48c39c73b7dc2930f7d3b
Reviewed-on: https://chromium-review.googlesource.com/344289
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add generic PWM host commands for setting + getting duty cycle. PWMs can
be controlled through index (board-specific meaning) or by type
(currently KB backlight and display backlight are supported, more can be
added as needed).
BUG=chrome-os-partner:52002
BRANCH=None
TEST=Manual on chell.
`ectool pwmsetduty kb 100` - Verify KB backlight goes to 100%
`ectool pwmgetduty kb` - Prints 100
`ectool pwmgetduty 0` - Prints 100
`ectool pwmsetduty 0 0` - Verify KB backlight goes to 0%
`ectool pwmgetduty kb` - Prints 0
`ectool pwmgetduty disp` - Error res 3 (unsupported PWM type)
`ectool pwmsetduty 1` - Error res 3 (non-existent PWM index)
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I607c92a291e6c2e3af8238eaf22ad2bb81ffc805
Reviewed-on: https://chromium-review.googlesource.com/344012
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
This change modifies the behavior of RBOX by blocking the key0 and key1
output, when the power button is pressed. It also adds support for
printing debug statements when various RBOX interrupts are triggered.
BUG=none
BRANCH=none
TEST=On cr50 test board verify key0 and key1 out are not asserted unless
the power button is pressed.
Change-Id: I67a3c1b8009279015bdc87bcf0995cffa9ab6f03
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/341470
Tested-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Add PWM_CONFIG_DSLEEP PWM config flag, which can be set to keep a
channel active during low-power idle / deep sleep. Currently it's
supported by npcx and mec1322.
BUG=chrome-os-partner:52783
BRANCH=glados
TEST=Manual on chell w/ subsequent commit + CONFIG_LOW_POWER_S0. Verify
KB backlight does not flicker during idle.
Change-Id: Ib9df5879aaa7dfa5764de1583496de84d40d2bb5
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/341002
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
GPIO console commands currently only show input voltage level,
and can only set level on predefined outputs.
This change allows GPIOs to be cycled between output, input,
and alternate function, as well as displaying the mode and
asserted level (if any) in gpioget.
This change creates CONFIG_CMD_GPIO_EXTENDED
as the internal gpio interface needs to be changed to support
this, and I can't test the other architectures. It may be
worthwhile to add this for all, or not.
This change is also necessary also for servo micro JTAG and PD
UART support, as several pins are tied together on the flex
and stm32 outputs need to be variously active or in high-z
depending on mode.
BUG=chromium:571477
TEST=gpioget <0|1|IN|A|ALT>; gpioget;
BRANCH=None
Change-Id: Iba32992db6244ee1e654db840d1c9c11dd2a0993
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338885
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
The cr50 SPI master can control the external AP and EC SPI ROM. This
change adds support for doing spi_transactions, but does not use the SPI
transactions for anything except console commands. This support will be
used for flashing the AP and EC through CCD. For now AP and EC flash
select must be done manually using the spi_flash_select console command.
Flash select should be disabled after use, because it will prevent the
system from booting.
BUG=chrome-os-partner:50701
BRANCH=none
TEST=Enable spi_flash commands. Select AP ROM and verify spi_flashinfo,
read, erase, and write commands work properly. Select EC ROM and verify
the same commands.
Change-Id: I16c55015794f8513effe0fa5712488a84bed2627
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/339844
Reviewed-by: Shawn N <shawnn@chromium.org>
This patch adds initial set of files to bring up STM32L476G-Eval board.
BUG=none
BRANCH=tot
TEST=Tested console. make buildall && make tests
Change-Id: I0c0f73f31e84099746fced4214c5ed7f45468cef
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/340100
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This adds support for RD Detection on cr50. It can be used to detect a
debug device and signal the controller to switch from the AP PHY to the
to CCD PHY. When RDCC1 and 2 no longer detect the debug device, then
the controller switches back to using the USB to AP PHY.
BUG=chrome-os-partner:50700
BRANCH=none
TEST=change the value on RDCC1 and RDCC1 and check that the usb
controller connects to the right PHY.
Change-Id: Ice01a45a31fe1932945f89df2e3b851f4d287a17
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338454
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This enables the Cr50 to accept RW firmware updates over USB.
BUG=chrome-os-partner:50707, chrome-os-partner:50712
BRANCH=none
TEST=make buildall; test on Cr50
Build and run the extra/usb_updater utility. Watch the console,
and observe that the Cr50 updates and reboots into the new image
correctly.
Note that you'll have to rebuild the ec.bin image in order for
the update to take effect. Just reflashing the same image doesn't
cause the bootloader to change its selection.
All the previously existing endpoints continue to function normally.
Change-Id: I7bd22eae803c2ceeb14a767c06d3d5c9f1ac7c7a
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338089
Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
This re-factors the existing firmware upgrade facility, which worked as
a TPM command extension.
The same code processing upgrade blocks prepended by the truncated
SHA1 and the load address is now used by both extended TPM command and
the USB upgrader.
To accommodate USB communications using a smaller message payloads a
reassembly layer is introduced which accumulates short USB payloads
into a single block which can be passed to the firmware upgrade
routine. USB encapsulation adds one 4 byte header at the beginning of
the block to hold the total block size. The reassembly layer keeps
receiving USB messages, concatenating their payloads until the full
block is received.
A config option is added to make sure the module is not compiled when
not needed.
BUG=chrome-os-partner:50707
BRANCH=none
TEST=make buildall; test on Cr50 - with the rest of the patches
applied it is possible to upgrade firmware using the USB utility
on the host..
Change-Id: Ib30b381c4ab196ea9d352f3c6b8f46dc23ddd599
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338087
The scheme to disable PD communication in locked RO needs to be
implemented on other platforms, so move it to common code, behind
CONFIG_USB_PD_COMM_LOCKED.
BUG=chrome-os-partner:52157
BRANCH=glados
TEST=Manual on chell. Lock system and boot to recovery, then verify PD
communication is functional. Enable CONFIG_USB_PD_COMM_LOCKED and verify
PD communication isn't functional under the same test conditions.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I8d1f24c0b60cf1c54e329af003b7083ee55ffc40
Reviewed-on: https://chromium-review.googlesource.com/338064
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
modify g781.c/.h to g78x.c/.h to suppor both G781/G782 temp sensor
based on CONFIG_TEMP_SENSOR_G781 or CONFIG_TEMP_SENSOR_G782
BUG=none
BRANCH=none
TEST=make buildall; able to get temperature data on board with G782
Change-Id: Ia32c85e9964bfd7c0c5263f04368bc001a27fe10
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/334228
Reviewed-by: Shawn N <shawnn@chromium.org>
This is keyboard test mechanism request for "multiple key press test",
we can thru the testing to scan out kso ksi pins shortting or keyboard has
multiple key pressing, below was the testing steps:
1. Turn off internal keyboard scan function.
2. Set all scan & sense pins to input and internal push up.
3. Set start one pin to output low.
4. check other pins status if any sense low level.
5. repeat step 3~4 for all keyboard KSO/KSI pins.
6. Turn on internal keyboard scan function.
BUG=chrome-os-partner:49235
BRANCH=ToT
TEST=manual
Short any KSO or KSI pins and excute "ectool kbfactorytest", it shows failed.
if no pins short together, it shows passed.
Change-Id: Id2c4310d45e892aebc6d2c0795db22eba5a30641
Signed-off-by: Devin Lu <Devin.Lu@quantatw.com>
Reviewed-on: https://chromium-review.googlesource.com/332322
Reviewed-by: Shawn N <shawnn@chromium.org>
1. Always use wake-up control interrupt for keyboard KSI. This can also
wake-up EC from deep doze / sleep mode.
2. In keyboard ISR, we just clear interrupt status to prevent keyboard
interrupt can't be re-enabled.
(for example, a KSI interrupt wakes up keyboard scan task,
but keyboard_raw_read_rows() got 0.)
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=keyboard function is normally.
Change-Id: If8c292189c6133b179a63dedcb7a18abbc091312
Reviewed-on: https://chromium-review.googlesource.com/333865
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add a usb endpoint and class for i2c control via USB.
Used for servo micro and servo_v4 to export USB control
through servod.
BUG=chromium:571477
BRANCH=None
TEST=updated servod is able to control gpio extender on servo_micro
Signed-off-by: Nick Sanders <nsanders@google.com>
Change-Id: Id44096f8c9e2da917c0574d28dfcbcc0adf31950
Reviewed-on: https://chromium-review.googlesource.com/329322
Commit-Ready: Nick Sanders <nsanders@chromium.org>
Tested-by: Nick Sanders <nsanders@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Use built-in USB periperal to detect BC1.2 suppliers and update the
charge manager.
BUG=chrome-os-partner:48658
BRANCH=None
TEST=manual for lucid. Use a samus as the supplier, and insert the
charger into Lucid. Verify that it identifies it as SDP. Use a wall
charger and verify that Lucid identifies it as DCP.
Change-Id: I7842e9f75874f727837df5bfc28690662caf821c
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/329236
Reviewed-by: Shawn N <shawnn@chromium.org>
this is to move the existing code from chipset level to board level
since PseudoG3 is a board feature that required specific hardware.
BUG=none
BRANCH=glados
TEST=use hibernate command to enter PseudoG3
Change-Id: I309ef89e0ff7057ce46c634baa9791731a771984
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/327677
Reviewed-by: Shawn N <shawnn@chromium.org>
Adds a JEDEC SFDP v1.* compatible Serial NOR Flash driver to control
multiple Serial NOR Flash devices (NOR EEPROMs, etc.). The SFDP tables
are used to discover parts' page sizes and capacities.
This driver only supports parts with capacities under 4GiB. If the
parts are larger than 16MiB, then the 0xB7 4-Byte addressing mode
entry opcode and 0xE9 4-Byte addressing mode exit opcode are required.
This driver also assumes that a 4KiB erase opcode of 0x20 is always
available.
BRANCH=none
BUG=none
TEST=Tested on cr51 with multiple EEPROMs with various SFDP revs
Change-Id: I5c2b757267e23c4f22ac89c6d5048a54b04de0c3
Signed-off-by: Ewout van Bekkum <ewout@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/321922
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
The TCPCI specification defines ane optional register
18h 'CONFIG_STANDARD_OUTPUT' providing a standardized way
of steering the high-speed muxes.
Implement the feature as a usb_mux_driver, under the conditional flag
CONFIG_USB_PD_TCPM_MUX.
The USB PD port index should be set in the port_addr field of the
'usb_mux' structure.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:49605
TEST=run pdeval-stm32f072 connected to a Parade PS8751 board and test USB/DP
muxing.
Change-Id: I7e5f0b8ec70b1910b2cff9d106514baca8c899e5
Reviewed-on: https://chromium-review.googlesource.com/322956
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
1. The previous EC2I module does not meet section
'7.17.5 EC2I Programming Guide'. We need to correct it to prevent
conflict with H2RAM (LPC I/O cycles 800h ~ 9ffh) which cause LPC keeps
long wait states.
NOTE:
If EC is using EC2I internal bus to access PNPCFG registers while host
accessing EC ram through H2RAM interface at the same time,
the symptom will appear.
2. Remove 'CONFIG_IT83XX_PNPCFG_HOST_ACCESS'.
We don't allow the host access PNPCFG registers.
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=1. To use console command 'rwreg' to r/w PNPCFG registers and
there is no error code return.
2. To create a stress test for this change.
- EC use 'ec2i_read()' and 'ec2i_write()' to access PNPCFG
registers per-10ms.
- run ectool 'version' command per-100ms.
Before the change was made, LPC will keep in long wait states
immediately.
After the change, we run the test of ectool 'version' command
over 20000 times.
Change-Id: I84e86fc17ef624d4a60a1a051bc301ebdf56a3da
Reviewed-on: https://chromium-review.googlesource.com/323563
Commit-Ready: Dino Li <dino.li@ite.com.tw>
Tested-by: Dino Li <dino.li@ite.com.tw>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This adds a temporary secure storage interface for the EC to be able
to store small amounts of data from the host that is locked until the
chipset resets. This is used by pre-memory verified boot on x86 systems
where we need to know which RW slot to boot and what the hash is to
ensure that we can resume from S3 safely.
BUG=chrome-os-partner:46049
BRANCH=none
TEST=tested on glados and samus
Change-Id: I5fa91046437479bcae69a8fca4c989b0ef554bbf
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/315222
Commit-Ready: Aaron Durbin <adurbin@chromium.org>
Tested-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
There are hooks for chipset power sequencing but not one to indicate
that the system has reset at runtime. Add a hook for this and
implement for lm4 and mec1322. The hook is notified on any platform
reset, including those that happen on the way into S3/S5 state.
There is a new config variable added because the hook is notified in
the interrupt handler and needs a deferrable function that needs to
be added to every board.
BUG=chrome-os-partner:46049
BRANCH=none
TEST=tested on glados and samus
Change-Id: I3be639414e18586344e0ec84632a50dfc1df586b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/315221
Commit-Ready: Aaron Durbin <adurbin@chromium.org>
Tested-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Configuring all GPIOs to INPUT / PULL_UP in hibernate is not a good
idea:
- INPUT / PULL_UP is not necessarially the lowest-power state (for
example, if there is an onboard pull-down).
- Most GPIOs should already be in lowest-power state when we're in S5.
- For the few GPIOs that need to be in a different state for hibernate,
we can use a board-level callback.
In addition, remove mec1322 code related to restoring from hibernate
state, since we always reset coming out of hibernate.
BUG=chrome-os-partner:49608
BRANCH=glados, strago
TEST=`hibernate` on chell console when in S5 and AC removed. Verify that
EC power is roughly equivalent to low-power idle power. Attach Zinger,
verify that device wakes and boots, and charges from charger.
Change-Id: Ib00ef035bec32cea3847eb38d743f5c0cec896ca
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/322937
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
In order to pulse RTC reset to the PCH when power sequencing exit fails we
need to watch for SLP_S4 to deassert and if it does not then assert RTCRST
using a board specific method. This is attempted up to 5 times before giving
up and staying in G3.
On skylake the RSMRST passthru needs to be honored when the task is woken up,
so while waiting call handle_rsmrst() if woken up early. This is needed
because it is RSMRST that actually tells the PCH to try and wake.
This is all wrapped in a config option and board specific method because not all
boards have a GPIO to control RTCRST and if they do they may not all use the
same method to assert it.
BUG=chrome-os-partner:49564
BRANCH=glados
TEST=manually tested on chell EVT:
First, ensure board sequences properly if everything is OK for a normal boot.
Next, modify handle_rsmrst() to not pass through the signal in order to
simulate being stuck in S5, and ensure that the EC attempts to assert RTCRST
and power up again 5 times before giving up and staying in G3.
Change-Id: Ia3c13069c92762b51beb682a19e5a074194a3c26
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/322724
Reviewed-by: Shawn N <shawnn@chromium.org>
Add support for continuously writing ADC samples to a circular buffer.
CONFIG_ADC_PROFILE_FAST_CONTINUOUS should be defined and an
appropriate sized buffer must be passed to adc_read_all_channels().
BUG=chromium:569994
TEST=Manual on snoball. Verify 'adc' continues to function (single
mode). With pending commit, verify that continuous conversion interrupt
is called at appropriate frequency and values look consistent.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I025825d72a698f8f1f4f95a89477df791bd5e67e
Reviewed-on: https://chromium-review.googlesource.com/318505
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
