Allow the host to self-report its sleep state through
EC_CMD_HOST_SLEEP_EVENT, which will typically be sent with SUSPEND
param when the host begins its sleep process. While the host has
self-reported that it is in SUSPEND, don't assert the interrupt
line, except for designated wake events.
BUG=chrome-os-partner:56156
BRANCH=None
TEST=On kevin, run 'ectool hostsleepstate suspend', verify that
interrupt assertion is skipped for battery host event. Run 'ectool
hostsleepstate resume' and verify interrupt is again asserted by the
battery host event.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I74288465587ccf7185cec717f7c1810602361b8c
Reviewed-on: https://chromium-review.googlesource.com/368391
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Servo_micro sets usb config maxpower to 100mA.
Servo_v4 is set to self powered as it's powered by a
shared vbus and not be the bub it's connected to.
cr50 is self powered as no power is transmitted as part of CCD.
* Add CONFIG_USB_MAXPOWER_MA to define USB maximum power draw requested
per board.
* Add CONFIG_USB_SELF_POWERED to indicate that a device is not
powered by allocated USB power.
BUG=chromium:631302
TEST=lsusb reports 100mA bMaxPower (micro), Self powered (v4)
BRANCH=None
Change-Id: I79b8ce46f32d94f16104a4a8080104e30dce7f2c
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/363153
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add a case statement to handle HCI commands.
Add a test commands.
Try to match the hcitool syntax, so the same commands
can be executed on a Linux host.
Added lcmd (long cmd) to pass more parameters in fewer arguments
BUG=None
BRANCH=None
TEST=Use HCI commands to configure an advertiser and listen for
it using `hcitool lescan` on the host.
Change-Id: Ie28038847c9549eb1c27a605aa0fbad5efd3b2c7
Signed-off-by: Myles Watson <mylesgw@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/362145
Commit-Ready: Dan Shi <dshi@google.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reef doesn't have the battery temperature sense pin connected to
the charger, hence reading the battery temperature from the battery
registers.
BUG=chrome-os-partner:55834
BRANCH=none
TEST=Using 'battery' & 'temps' console command verified,
temperature readings are same from both the commands.
Change-Id: I897e453296151f31344f3e0434202baa67c7025d
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/365970
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
When the case close debug (CCD) feature is provided by an external chip
(e.g security chip or TCPC), we still need to be able to detect debug
accessory with Rd/Rd (by setting Rp/Rp when VBUS is detected without
seeing Rp).
Add a CONFIG_CASE_CLOSED_DEBUG_EXTERNAL configuration parameter for this
case.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=chrome-os-partner:55410
TEST=manual:on Kevin, enable CONFIG_CASE_CLOSED_DEBUG_EXTERNAL,
plug a SuzyQ (with Rd/Rd) and verify that the device in debug mode
when transitioning to S5.
Change-Id: Ie04a000a7b0eb670e3808f7bca1180298dfcd9db
Reviewed-on: https://chromium-review.googlesource.com/363400
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
This copies the generic USB update code into common
so it can be used on other platforms. There should be
no functional change. cr50 folks want no change to their
code so vbendeb@chomium.org will refactor this back
together at a later date.
BUG=chromium:571476
TEST=none
BRANCH=none
Change-Id: I710afb22940013e7db5d8694898b90c0ae245777
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/362131
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Currently, the matrix keyboard protocol does not have support for
handling non-matrixed keys. This commit adds support for buttons which
do not appear in the keyboard matrix as well as switches.
Additionally, the keyboard FIFO is now just a general MKBP events FIFO
which MKBP events are free to use. Now, buttons and switches wil join
the key matrix event.
BUG=chrome-os-partner:54988
BUG=chrome-os-partner:54976
BUG=chromium:626863
BRANCH=None
TEST=Flash kevin, and verify that keyboard is still functional.
TEST=make -j buildall
CQ-DEPEND=CL:358926
Change-Id: If4ada904cbd5d77823a0710d4671484b198c9d91
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/358633
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
cts.tasklist contains tasks run only for CTS. These tasks are added to the
tasks registered in ec.tasklist with higher priority. This design allows
board directories to be free from CTS stuff.
cts.tasklist can be placed in each suite directory (cts/suite/cts.tasklist).
If a suite does not define its own cts.tasklist, the common list is used
(i.e. cts/cts.tasklist).
BUG=chromium:624520
BRANCH=none
TEST=Ran the followings:
make buildall
make CTS_MODULE=gpio BOARD=nucleo-f072rb
make CTS_MODULE=gpio BOARD=stm32l476g-eval
Change-Id: Ibb242297ee10a397a8fcb6ff73d8cbc560daa885
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/359445
Reviewed-by: Chris Chen <twothreecc@google.com>
elm EC console output is very spammy, as EC_CMD_MOTION_SENSE_CMD
is called every 100ms, so we want to set "hcdebug" to "off" as
the default (which still includes errors, but no "normal"
commands).
BRANCH=none
BUG=chrome-os-partner:55001
TEST=make buildall -j
TEST=Flash elm EC, see that output is fairly quiet.
Change-Id: I70d91c291d934b4f032e5c57f3c333e2c10b93bc
Reviewed-on: https://chromium-review.googlesource.com/359112
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
For certain board configurations, KSI2 will be stuck asserted for all
scan columns if the power button is held. We must be aware of this case
in order to correctly handle recovery mode key combinations.
BUG=chrome-os-partner:54602
BRANCH=None
TEST=Manual on gru. Do three-key salute, verify EC detects recovery mode.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I03d76e1121107484f79520745858388f6cae096c
Reviewed-on: https://chromium-review.googlesource.com/357590
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Not everything with a temperature sensor uses thermal throttling. This
change modifies the conditional build to enable building temp sensor
source without thermal throttling.
BUG=none
BRANCH=none
TEST=make buildall -j
Change-Id: I8c0753f12899e9f203c04477ae520bcda40d5fd8
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/356484
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Added console commands for the debugging purpose
psys - Can be used to measure the system power
amonbmon - Can be used to measure AMON/BMON voltage diff, current
BUG=chrome-os-partner:54273
BRANCH=none
TEST=Manually tested on Amenia
psys - Ran fish task and observed psys value changes.
amonbmon - AMON & BMON voltage & current are same as measured
across sense resistors.
Change-Id: I6653e814d9b00efe7dae9ce1fbd7ddbc2356f8e0
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/353043
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
For designs where the host SOC is responsible for setting the USB-C SS
mux, the EC must track the desired mux state and inform the host when
the desired state changes. Then, the host must ask the EC for the new
desired state and set the mux accordingly.
BUG=chrome-os-partner:52639
BRANCH=None
TEST=Manual on gru with subsequent commit.
Attach USB dongle in port 1 and DP dongle in port 0, then verify `ectool
usbpdmuxinfo` output:
Port 0: DP
Port 1: USB
Flip DP dongle and verify output changes:
Port 0: DP INV
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I6a99ce93a76c3197f9195cfaa25c5217d09aeb75
Reviewed-on: https://chromium-review.googlesource.com/355281
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Add a host event to support MKPB:
When sent, the ACPI code will send a notification to the kernel
cros-ec-lpcs driver that will issue EC_CMD_GET_NEXT_EVENT.
We can allow code (sensor stack for instance) that uses MKBP to work
on ACPI based architecture.
Obviously, host event over MKPB is not supported.
BRANCH=none
BUG=b:27849483
TEST=Check we get sensor events on Cyan through the sensor ring.
(cyan branch)
Change-Id: Iadc9c852b410cf69ef15bcbbb1b086c36687c687
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/353634
Reviewed-by: Randall Spangler <rspangler@chromium.org>
ANX7688 is a TCPCI compatible port controller with HDMI to DP converter.
The HDMI converter needs a reset every time after enabling its function.
BRANCH=none
BUG=chrome-os-partner:52815
TEST=manual
boot elm proto
plug and unplug dingdong and check DP output
plug/unplug adapter and check pd 0 state
Change-Id: I774421d7b0b8d2cfd31e860fcd4eaed08ee48ac7
Signed-off-by: Rong Chang <rongchang@chromium.org>
Signed-off-by: Tang Zhentian1 <ztang@analogixsemi.com>
Reviewed-on: https://chromium-review.googlesource.com/340371
Commit-Ready: Koro Chen <koro.chen@mediatek.com>
Tested-by: Koro Chen <koro.chen@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
This commit includes changes required for
supporting a hardware based montgomery
modexp (r = a ^ e mod N).
The function bn_is_bit_set() was previously
static, and now added to internal.h, as this
function is used by the hardware implementation.
Add function declarations for new functions
related to the hardware implementation to
chip/g/dcrypto/internal.h
BRANCH=none
CQ-DEPEND=CL:*260618,CL:*260895
BUG=chrome-os-partner:43025,chrome-os-partner:47524
TEST=all tests in test/tpm_test/tpmtest.py pass
Change-Id: I5fe4a6692678b64f27659f42a08d200b6fe6f0cc
Signed-off-by: nagendra modadugu <ngm@google.com>
Reviewed-on: https://chromium-review.googlesource.com/347462
Commit-Ready: Nagendra Modadugu <ngm@google.com>
Tested-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
This commands makes it possible to control the PD chip (or
the interaction between EC and PD), from the AP.
- PD_SUSPEND: Suspends the PD chip: EC needs to stop talking
to PD chip. Useful at beginning of PD FW update.
- PD_RESUME: Resumes the PD chip: EC can start talking to PD
chip again. Useful at end of PD FW update.
- PD_RESET: Resets the PD chip (called at the end of the update).
- PD_CONTROL_DISABLE: Prevents further calls to this command
(for security reason, we do not want the AP to be able to
call the other subcommands after the update has been performed).
BRANCH=none
BUG=chrome-os-partner:52433
TEST=ectool pdcontrol {suspend,resume,reset,disable}
Change-Id: I7a955dd27b65086c21d195a6504aa7392eb0406d
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/342584
Reviewed-by: Randall Spangler <rspangler@google.com>
add a new config flag to support active low power control signal
BUG=chrome-os-partner:53665
BRANCH=none
TEST=Use multimeter to check for voltage present on the WiFi slot.
Use gpioget to check GPIO state in S0 (on) and S5 (off).
Change-Id: Ibeca88d16f39eadd7f29589cd3cd15aeef0dd524
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/347085
Commit-Ready: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Kevin uses inverted polarity (low = enable 5V output), so add a new CONFIG
to support this.
BUG=chrome-os-partner:53777
BRANCH=None
TEST=Manual on Kevin. Enable USB charger tasks, verify that VBUS is
properly detected on no-battery case.
Change-Id: Ifb3e5fa9db1973d9826435712711f0cb0fd1d3a5
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/349260
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Previously CONFIG_USB_PD_TCPM_VBUS had two uses which were independent:
- When operating as a TCPC, it indicated that the VBUS level should be
tracked (through GPIO inputs) and sent to the external TCPM when
appropriate.
- When operating as a TCPM, it indicated that the VBUS level should be
obtained by querying the TCPC.
These two independent uses have been split into
CONFIG_USB_PD_TCPC_TRACK_VBUS and CONFIG_USB_PD_VBUS_DETECT_TCPC, which
sould be more clear.
In addition, CONFIG_USB_PD_VBUS_DETECT_* CONFIGs have been added for
other means of VBUS detection.
BUG=chromium:616580
BRANCH=None
TEST=Verify kevin continues to boot + charge.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I936821481d6577e17e3e9c61ff97c037574d6923
Reviewed-on: https://chromium-review.googlesource.com/348950
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
move PRECHARGE_TIMEOUT to config.h so that we can customize precharge time to
meet client's spec.
BUG=none
BRANCH=master
TEST=`make -j buildall`, precharge time is set to 300s in elm.
Change-Id: I5c3bf0d5c5240b9c087e6cdb7c6e97301efa9f84
Signed-off-by: Ryan Zhang <Ryan.Zhang@quantatw.com>
Reviewed-on: https://chromium-review.googlesource.com/348151
Reviewed-by: Shawn N <shawnn@chromium.org>
Port SHA and P256 code to depend on third_party/cryptoc.
Remove config options CONFIG_SHA1, and CONFIG_SHA256 as
these are provided by third_party/cryptoc.
Also remove unused config options CONFIG_SHA384, CONFIG_SHA512.
Crypto functions prefixed by dcrypto_ (declared in internal.h ),
DCRYPTO_ (declared in dcrypto.h) are implemented under
chip/g/dcrypto, and otherwise are implemented under third_party/cryptoc.
BRANCH=none
BUG=chrome-os-partner:43025,chrome-os-partner:47524,chrome-os-partner:53782
TEST=all tests in test/tpm_test/tpmtest.py pass
Change-Id: If7da02849aba9703573559370af5fae721d594fc
Signed-off-by: nagendra modadugu <ngm@google.com>
Reviewed-on: https://chromium-review.googlesource.com/340853
Commit-Ready: Nagendra Modadugu <ngm@google.com>
Tested-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
There are a couple of issues that cr50 has when it cannot know the state
of servo, the EC, and the AP. This change adds support so we can detect
when the AP or EC has been powered on and when servo has been connected.
It uses the UART RX signals to monitor the power state of the AP and EC.
The TX signals are used to monitor the state of servo.
BUG=chrome-os-partner:52056,chrome-os-partner:52322
BRANCH=none
TEST=verify device states are correct when the AP and EC are powered on
or off and when Servo is attached or detached
Change-Id: Id0a2281b65cb367ecc8d0ca2f9a576672318a5fb
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/344019
Full implementation of NvMem read, write, and commit functions.
Includes partition definitions, shared memory allocation, and
initialization function.
Includes a set of unit tests located in ec/test/nvmem.c which
verify functionality.
This module is required by Cr50, however this CL does not
include any Cr50 specific code.
BUG=chrome-os-partner:44745
BRANCH=none
TEST=manual
make runtests TEST_LIST_HOST=nvmem and verify that all tests pass
Change-Id: I515b094f2179dbcb75dd11ab5b14434caad37edd
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/345632
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This change provides a console command for setting,
and loading a usb serial number from flash. This
feature adds CONFIG_USB_SERIALNO, and currently only
has a useful implementation when PSTATE is present.
BUG=chromium:571477
TEST=serialno set abcdef; serialno load; reboot
BRANCH=none
Change-Id: I3b24cfa2d52d54118bc3fd54b276e3d95412d245
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/337359
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This allows the AP to protect a I2C passthru bus. A board-specific
function then defines what I2C commands are allowed, so that we
can white/black list some addresses (e.g. I2C address allowing
PD chip FW updating).
BRANCH=none
BUG=chrome-os-partner:52431
TEST=Book elm-rev1
Change-Id: Ib106924418b16388ea8ea53c7b6bda6ef92e1d09
Signed-off-by: Nicolas Boichat <drinkcat@google.com>
Reviewed-on: https://chromium-review.googlesource.com/345761
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@google.com>
LPC access interrupt only enabled when EC entering deep doze mode. This
will reduce interrupt of LPC access. Also, this interrupt is always
enabled for LPC platform to support "CONFIG_LOW_POWER_S0".
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=Tested ectool command 'version' x 10000.
Change-Id: I9053c4018b38a8a852c3c6254e1fcde625f3fa3a
Reviewed-on: https://chromium-review.googlesource.com/336112
Commit-Ready: Dino Li <dino0303@gmail.com>
Tested-by: Dino Li <dino0303@gmail.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Driver implements TCPC for ANX74xx chips. Enables Type C
port for USB and DP alt mode. Enable port role swap feature.
Driver implements TCPC for ANX74xx chips firmware version 1.0 and later.
Please update to ANX74xx firmware to V1.0 or later version to work.
Change list:
1, modify the position of define and struct declare
which response the comment for patch 22.
BUG=chrome-os-partner:49510
BRANCH=none
TEST=tested compiled binary for pdeval-stm32f072 board with this patch.
Power contract establishment, port role swap, DP alt mode works fine.
Change-Id: Iae6322510605a08d3bdd08446116ef5f9e4f7a7c
Signed-off-by: Aman Kumar <akumar@analogixsemi.com>
Signed-off-by: Junhua Xia <jxia@analogixsemi.com>
Reviewed-on: https://chromium-review.googlesource.com/322433
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
Previously usb_charger.c supported only pi3usb9281, but now support for
additional parts is required. Move pericom-specific code (including the
usb_charger tasks that handles various quirks of that part) to the
pi3usb9281 usb_switch driver.
Going forward, usb_switch drivers must implement
usb_charger_set_switches() and must have some method (such as a task or
interrupt handler) to update charge_manager with information about
attached chargers.
BUG=chrome-os-partner:53363
BRANCH=None
TEST=`make buildall -j`
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I4df74e043d8cf2e532d48c39c73b7dc2930f7d3b
Reviewed-on: https://chromium-review.googlesource.com/344289
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add generic PWM host commands for setting + getting duty cycle. PWMs can
be controlled through index (board-specific meaning) or by type
(currently KB backlight and display backlight are supported, more can be
added as needed).
BUG=chrome-os-partner:52002
BRANCH=None
TEST=Manual on chell.
`ectool pwmsetduty kb 100` - Verify KB backlight goes to 100%
`ectool pwmgetduty kb` - Prints 100
`ectool pwmgetduty 0` - Prints 100
`ectool pwmsetduty 0 0` - Verify KB backlight goes to 0%
`ectool pwmgetduty kb` - Prints 0
`ectool pwmgetduty disp` - Error res 3 (unsupported PWM type)
`ectool pwmsetduty 1` - Error res 3 (non-existent PWM index)
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I607c92a291e6c2e3af8238eaf22ad2bb81ffc805
Reviewed-on: https://chromium-review.googlesource.com/344012
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
This change modifies the behavior of RBOX by blocking the key0 and key1
output, when the power button is pressed. It also adds support for
printing debug statements when various RBOX interrupts are triggered.
BUG=none
BRANCH=none
TEST=On cr50 test board verify key0 and key1 out are not asserted unless
the power button is pressed.
Change-Id: I67a3c1b8009279015bdc87bcf0995cffa9ab6f03
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/341470
Tested-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Add PWM_CONFIG_DSLEEP PWM config flag, which can be set to keep a
channel active during low-power idle / deep sleep. Currently it's
supported by npcx and mec1322.
BUG=chrome-os-partner:52783
BRANCH=glados
TEST=Manual on chell w/ subsequent commit + CONFIG_LOW_POWER_S0. Verify
KB backlight does not flicker during idle.
Change-Id: Ib9df5879aaa7dfa5764de1583496de84d40d2bb5
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/341002
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
GPIO console commands currently only show input voltage level,
and can only set level on predefined outputs.
This change allows GPIOs to be cycled between output, input,
and alternate function, as well as displaying the mode and
asserted level (if any) in gpioget.
This change creates CONFIG_CMD_GPIO_EXTENDED
as the internal gpio interface needs to be changed to support
this, and I can't test the other architectures. It may be
worthwhile to add this for all, or not.
This change is also necessary also for servo micro JTAG and PD
UART support, as several pins are tied together on the flex
and stm32 outputs need to be variously active or in high-z
depending on mode.
BUG=chromium:571477
TEST=gpioget <0|1|IN|A|ALT>; gpioget;
BRANCH=None
Change-Id: Iba32992db6244ee1e654db840d1c9c11dd2a0993
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338885
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
The cr50 SPI master can control the external AP and EC SPI ROM. This
change adds support for doing spi_transactions, but does not use the SPI
transactions for anything except console commands. This support will be
used for flashing the AP and EC through CCD. For now AP and EC flash
select must be done manually using the spi_flash_select console command.
Flash select should be disabled after use, because it will prevent the
system from booting.
BUG=chrome-os-partner:50701
BRANCH=none
TEST=Enable spi_flash commands. Select AP ROM and verify spi_flashinfo,
read, erase, and write commands work properly. Select EC ROM and verify
the same commands.
Change-Id: I16c55015794f8513effe0fa5712488a84bed2627
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/339844
Reviewed-by: Shawn N <shawnn@chromium.org>
This patch adds initial set of files to bring up STM32L476G-Eval board.
BUG=none
BRANCH=tot
TEST=Tested console. make buildall && make tests
Change-Id: I0c0f73f31e84099746fced4214c5ed7f45468cef
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/340100
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This adds support for RD Detection on cr50. It can be used to detect a
debug device and signal the controller to switch from the AP PHY to the
to CCD PHY. When RDCC1 and 2 no longer detect the debug device, then
the controller switches back to using the USB to AP PHY.
BUG=chrome-os-partner:50700
BRANCH=none
TEST=change the value on RDCC1 and RDCC1 and check that the usb
controller connects to the right PHY.
Change-Id: Ice01a45a31fe1932945f89df2e3b851f4d287a17
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338454
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This enables the Cr50 to accept RW firmware updates over USB.
BUG=chrome-os-partner:50707, chrome-os-partner:50712
BRANCH=none
TEST=make buildall; test on Cr50
Build and run the extra/usb_updater utility. Watch the console,
and observe that the Cr50 updates and reboots into the new image
correctly.
Note that you'll have to rebuild the ec.bin image in order for
the update to take effect. Just reflashing the same image doesn't
cause the bootloader to change its selection.
All the previously existing endpoints continue to function normally.
Change-Id: I7bd22eae803c2ceeb14a767c06d3d5c9f1ac7c7a
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338089
Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
